ALBERT

Description: To achieve higher Si solar cell efficiencies (greater than 20%), better single-crystal Si must be produced. It is believed possible to bring Cz (Czochralski) Si up to the same low recombination level as FZ (Float Zone) Si. It is also desirable that solar cell Si meet the following requirements: long minority carrier lifetime (0.2 ohm-cm p-type with tau less than 500 microsec); repeatedly uniform lifetime (not spread from 50 to 1000 microsec); a lifetime that does not decrease during normal device processing; a silicon wafer sheet that is flat and stays throughout normal device processing; uniform and reasonable mechanical strength; and, manufacture at low cost (less than $50/sq m).

Description: Efficiency and operating life is an economic attribute in silicon solar cells application. The efficiency improvements made during the 30 year existence of the silicon solar cells, from about 6% efficiency at the beginning to 19% in the most recent experimental cells is illustrated. In the more stationary periods, the effort was oriented towards improving radiation resistance and yields on the production lines, while, in other periods, the emphasis was on reaching new levels of efficiency through better cell design and improved material processing. First results were forthcoming from the recent efforts. Considerably more efficiency advancement in silicon solar cells is expected, and the anticipated attainment of efficiencies significantly above 20% is discussed. Major advances in material processing and in the resulting material perfection are required.

Description: Work in identifying, developing, and analyzing techniques for measuring bulk recombination rates, and surface recombination velocities and rates in all regions of high-efficiency silicon solar cells is presented. The accuracy of the previously developed DC measurement system was improved by adding blocked interference filters. The system was further automated by writing software that completely samples the unkown solar cell regions with data of numerous recombination velocity and lifetime pairs. The results can be displayed in three dimensions and the best fit can be found numerically using the simplex minimization algorithm. Also described is a theoretical methodology to analyze and compare existing dynamic measurement techniques.

Description: A survey of bulk recombination measurement techniques was presented. Classical methods were reviewed along with their limiting assumptions and simplifications. A modulated light measurement system was built and showed the large effects of junction capacitance. Techniques for extension of classical methods for measurement of multiparameter multiregression measurements were identified and analyzed.

Description: The present invention is directed to an apparatus for stirring materials using planar orthogonal axes oscillations. The apparatus has a movable slide plate sandwiched between two fixed parallel support plates. Pressurized air is supplied to the movable slide plate which employs a tri-arm air bearing vent structure which allows the slide plate to float and to translate between the parallel support plates. The container having a material to be stirred is secured to the upper surface of the slide plate through an aperture in the upper support plate. A motor driven eccentric shaft loosely extends into a center hole bearing of the slide plate to cause the horizontal oscillations. Novelty lies in the combination of elements which exploits the discovery that low frequency, orthogonal oscillations applied horizontally to a Bridgman crucible provides a very rigorous stirring action, comparable with and more effective by an order of magnitude than the accelerated crucible rotation technique.

Description: Horizontal vibration suggested as technique for more effective stirring of melts in crystal-growth apparatus. Vibrational technique may replace accelerated crucible rotation. Potential superiority of vibrational technique shown by preliminary experiments in which ink stirred into water.

Description: Air-cushion device provides vibrations along axes 90 degrees apart. Bearing includes movable slide sandwiched between two fixed support plates. Separation between plates adjusted to standard air-bearing tolerances. Pressurized air supplied to slide so it floats between plates on cushion of air. Air exhausts on top and bottom surfaces of three arms of slide. Developed for stirring crystal-growth liquids in containers.

Description: A generic comparison has been carried out of all methods for recombination parameter determination that are based on measurement of a current and/or voltage in either steady-state, transient, or frequency-dependent approaches. The theoretical background for the time-dependent methods has been extended from prior work to include drift fields and be applicable to compound (multilayered) regions. The key findings were: (1) all methods have essentially the same limitations to determination of only the dominant recombination parameters; (2) open-circuit measurements have more sensitivity to the recombination parameters than short circuit measurements, but they present much more difficulty in eliminating spurious effects; (3) transient and frequency-dependent methods have exactly the same expressions for the relaxation constants and the breakpoint frequencies; and (4) in compound regions there exists only one set of relaxation constants for all the coupled layers. These constants include all relevant parameters of these layers. It is thus difficult to separate these parameters in time- or frequency-domain measurements. ASLBIC seems still to be the most suitable method for determination of emitter parameters.

Description: The recent Titan Saturn System Mission (TSSM) proposal incorporates a montgolfiere (hot air balloon) as part of its architecture. Standard montgolfiere balloons generate lift through heating of the atmospheric gases inside the envelope, and use a vent valve for altitude control. A Titan aerobot (robotic aerial vehicle) would have to use radioisotope thermoelectric generators (RTGs) for electric power, and the excess heat generated can be used to provide thermal lift for a montgolfiere. A hybrid montgolfiere design could have propellers mounted on the gondola to generate horizontal thrust; in spite of the unfavorable aerodynamic drag caused by the shape of the balloon, a limited amount of lateral controllability could be achieved. In planning an aerial mission at Titan, it is extremely important to assess how the moon-wide wind field can be used to extend the navigation capabilities of an aerobot and thereby enhance the scientific return of the mission. In this paper we explore what guidance, navigation and control capabilities can be achieved by a vehicle that uses the Titan wind field. The control planning approach is based on passive wind field riding. The aerobot would use vertical control to select wind layers that would lead it towards a predefined science target, adding horizontal propulsion if available. The work presented in this paper is based on aerodynamic models that characterize balloon performance at Titan, and on TitanWRF (Weather Research and Forecasting), a model that incorporates heat convection, circulation, radiation, Titan haze properties, Saturn's tidal forcing, and other planetary phenomena. Our results show that a simple unpropelled montgolfiere without horizontal actuation will be able to reach a broad array of science targets within the constraints of the wind field. The study also indicates that even a small amount of horizontal thrust allows the balloon to reach any area of interest on Titan, and to do so in a fraction of the time needed by the unpropelled balloon. The results show that using the Titan wind field allows an aerobot to significantly extend its scientific reach, and that a montgolfiere (unpropelled or propelled) is a highly desirable architecture that can very significantly enhance the scientific return of a future Titan mission.

Description: A new method for rapidly stirring liquids has been developed which may be useful in crystal growth applications. The method involves the introduction of orthogonally coupled low frequency vibrations to fluids contained in cylindrical crucibles. A mathematical model has been developed to describe the influence of this vibrational stirring method on fluid flow. The optimum sloshing frequencies calculated for a specific system geometry were very close to those observed experimentally. A systematic study of the fluid flow induced by the vibrational motion was carried out at room temperature using aqueous solutions containing glycerine. Preliminary experiments were carried out to study the effect of vibrational stirring on interface shape and position during the Bridgman growth of CsCdCl3, a model system.