ALBERT

Description: Investigations have been conducted to determine by means of total-pressure surveys the boundaries of single and twin jets discharging through convergent nozzles into quiescent air. The jet boundaries for the region from the nozzle outlets to a station 6 nozzle diameters downstream are presented for nozzle pressure ratios ranging from 2.5 t o 16.0 and for twin-Jet nozzle center-line spacings ranging from 1.42 to 2.50 nozzle diameters. The effects of these parameters on the interaction of twin Jets are discussed. In order to ascertain the utility of the results for other than the test conditions, the effects of jet temperature, Reynolds number, and humidity on the pressure boundaries have been briefly investigated. The result indicate that for a jet of 2.6 the pressure boundaries are slightly smaller than those of corresponding unheated jets and that the effects of Reynolds number and humidity are negligible.

Description: An investigation was conducted on a 35 deg swept-wing fighter airplane to determine the effects of several blunt-trailing-edge modifications to the wing and tail on the high-speed stability and control characteristics and tracking performance. The results indicated significant improvement in the pitch-up characteristics for the blunt-aileron configuration at Mach numbers around 0.90. As a result of increased effectiveness of the blunt-trailing-edge aileron, the roll-off, customarily experienced with the unmodified airplane in wings-level flight between Mach numbers of about 0.9 and 1.0 was eliminated, The results also indicated that the increased effectiveness of the blunt aileron more than offset the large associated aileron hinge moment, resulting in significant improvement in the rolling performance at Mach numbers between 0.85 and 1.0. It appeared from these results that the tracking performance with the blunt-aileron configuration in the pitch-up and buffeting flight region at high Mach numbers was considerably improved over that of the unmodified airplane; however, the tracking errors of 8 to 15 mils were definitely unsatisfactory. A drag increment of about O.OOl5 due to the blunt ailerons was noted at Mach numbers to about 0.85. The drag increment was 0 at Mach numbers above 0.90.

Description: The effect of several armament installations on the drag of a 1/8 scale model of the B-32 airplane was determined. Turrets in the following positions were tested: nose, tail, upper forward, upper aft, and lower. The nose and tail turrets were each equipped with two.50-caliber guns. Upper turrets were of three types: two.50-caliber guns, four.50-caliber guns, and 20-millimeter cannon. Lower turrets were of two types: two.50-caliber guns and four.50-caliber guns. The effect of streamlining the upper two- and four-gun turrets and of extending the lower two-gun turret was determined. The tests were conducted in the Langley 19-foot. pressure tunnel at a Reynolds number of approximately 2,960,000 and a Mach number of 0.13. Large increases in drag coefficient were caused by the complete armament installations. At a lift coefficient of 0. 4 the installations with nonstreamlined upper turrets and the lower turret retracted increased the drag coefficient by 0.0022 and 0.0027 for the two-gun and four-gun turret installations, respectively. Streamlining the upper turrets reduced the drag of these installations by approximately 40 percent with the upper turrets streamlined, the drag increase was about the same for either the two- or four-gun turret installation. The streamlined two-cannon upper turrets increased the drag about the same amount as the two-gun upper turrets that were not streamlined. Extension of the lower turret. increased the drag slightly more than the whole streamlined gun-turret installation.

Description: Unduly high diving speeds can be effectively controlled by diving brakes but their employment involves at the same time a number of disagreeable features: namely, rotation of zero lift direction, variation of diviving moment, and, the creation of a potent dead air region.

Description: Urban Air Mobility (UAM) describes a new type of aviation focused on efficient flight within urban areas for moving people and goods. There are many different configurations of UAM vehicles, but they generally use an electric motor driving a propeller or ducted fan powered by batteries or a hybrid electric power generation system. Transmission cables are used to move energy from the storage or generation system to the electric motors. Though terrestrial power transmission cables are well established technology, aviation applications bring a whole host of new design challenges that are not typical considerations in terrestrial applications. Aircraft power transmission cable designs must compromise between resistance-per-length, weight-per-length, volume constraints, and other essential qualities. In this paper we use a multidisciplinary design optimization to explore the sensitivity of these qualities to a representative tiltwing turboelectric UAM aircraft concept. This is performed by coupling propulsion and thermal models for a given mission criteria. Results presented indicate that decreasing cable weight at the expense of increasing cable volume or cooling demand is effective at minimizing maximum takeoff weight (MTO). These findings indicate that subsystem designers should update their modeling approach in order to contribute to system-level optimality for highly-coupled novel aircraft. Mobility (UAM) vehicles have the potential to change urban and intra-urban transport in new and interesting ways. In a series of two papers Johnson et al.1 and Silva et al.2 presented four reference vehicle configurations that could service different niches in the UAM aviation category. Of those, this paper focuses on the Vertical Take-off and Landing (VTOL) tiltwing configuration shown in Figure 1. This configuration uses a turboelectric power system, feeding power from a turbo-generator through a system of transmission cables to four motors spinning large propellers on the wings. Previous work on electric cable subsystems leaves much yet to be explored, especially in the realm of subsystem coupling. Several aircraft optimization studies1, 3, 4 only considered aircraft electrical cable weight and ignored thermal effects. Electric and hybrid-electric aircraft studies by Mueller et al.5 and Hoelzen et al.6 selected a cable material but did not investigate alternative materials. Advanced cable materials have been examined by a number of authors: Alvarenga7 examined carbon nanotube (CNT) conductors for low-power applications. De Groh8, 9 examined CNT conductors for motor winding applications. Behabtu et al.,10 and Zhao et al.11 examined CNT conductors for a general applications. There were some studies that examined the thermal effects of cables but they did not allow the cable material to change; El-Kady12 optimized ground-cable insulation and cooling subject constraints. Vratny13 selected cable material based on vehicle power demand, and required resulting cable heat to be dissipated by the Thermal Management System (TMS). None of these previous studies allowed for the selection of the cable material based on a system level optimization goal. Instead, they focused on sub-system optimality such as minimum weight, which comes at the expense of incurring additional costs for other subsystems. Dama14 selected overhead transmission line materials using a weighting function and thermal constraints. However, that work was not coupled with any aircraft subsystems like a TMS. The traditional aircraft design approach, which relies on assembling groups of optimal subsystems, breaks down when considering novel aircraft concepts like the tiltwing vehicle. In a large part, this is because novel concepts have a much higher degree of interaction or coupling between subsystems. For example, when a cable creates heat, this heat needs to be dissipated by the TMS, which needs power supplied by the turbine, and delivering the power creates more heat. The cable, the TMS, and the turbine are all coupled. A change to one subsystem will affect all the other subsystems, much to the consternation of subsystem design experts. Multidisciplinary optimization is the design approach that can address these challenges. However, to fully take advantage of this, we must change the way we think about subsystem design. Specifically, we must move away from point design, and focus on creating solution spaces. The work presented in this paper uses the multidisciplinary optimization approach with aircraft level models to study the system-level sensitivity of cable traits: weight-per-length and resistance-per-length. Additionally, we examined the effects of vehicle imposed volume constraints on these traits. This is useful for three purposes: (1) to demonstrate a framework that can perform a coupled analysis between the aircraft thermal and propulsion systems, (2) to provide a method by which future cable designs can be evaluated against each other given a system-level design goal, (3) to provide insight into what cable properties may be promising for future research. This last element is explored given the caveat that the models contained in this analysis do not represent high-fidelity systems. Thus, while we can demonstrate coupling in between systems, the exact system-level sensitivity to a given parameter may change if a subsystem model or the assumptions governing that model change. The organization of this paper is as follows, in Sec II we outline a method to combine the VTOL vehicle design and cable information in order to produce cables sensitivity studies. Results analysis and discussion are contained in Sec III. Conclusions are presented in Sec IV.

Description: The aerodynamic characteristics in pitch of the Army Ordnance Corps T205 3.5-inch HEAT rocket with various head designs and one fin modification have been determined at velocities of 500, 700 and 900 feet per second in the Langley high-speed 7- by 10-foot tunnel. The results presented are those of the full-scale model. Comparison of results obtained at 500 feet per second shows, in general, that for changes on the forward portion of the head the missile configurations having the greatest stability - most rearward center-of-loads location - were those having the highest drag. However, very limited comparisons indicate that the shape of the rear position of the head may be an important factor in reducing the drag and increasing the restoring moments. Generally, large increases in drag were noted for the various head designs with an increase in Mach number from 0.62 to 0.82. Pitching-moment-curve slopes increased with Mach number on all models except those having reasonably well-faired forward sections. These models showed a decrease in stability with increases in Mach number.

Description: An experimental investigation has been made in the Langley stability tunnel at low speed to determine the static longitudinal and lateral stability characteristics of a l/9-scale powered model of the Convair XFY-1 vertically rising airplane. Effects of thrust coefficient were investigated for the complete model and for certain components of the model. Effects of control deflections and of propeller-blade angle were investigated briefly for the complete model. Most of the tests were made through an angle-of-attack range from about -4 deg. to 29 deg, and the thrust-coefficient range was from 0 t o 0.7. In order to expedite distribution of these data to interested persons, no analysis of the data has been prepared for this report,

Description: Detail calculations are presented of the shifts in stick-fixed neutral point of the Republic XF-12 airplane due to the windmilling propellers and to the fuselage. The results of these calculations differ somewhat from those previously made for this airplane by Republic Aviation Corporation personnel under the direction of Langley flight division personnel. Due to these differences the neutral point for the airplane is predicted to be 37.8 percent mean aerodynamic chord, instead of 40.8 percent mean aerodynamic chord as previously reported.

Description: An investigate ion was made of the disturbed motion of a gas for the harmonic vibrations of a thin slightly cambered wing of finite span moving forward with supersonic velocity. This problem was considered by E. A. Krasilshchikova who applied the method of Fourier series and obtained a solution of the space problem for the condition that the Mach cones drawn through the leading edge of the wing intersect the wing or are tangent to it. In this paper, a different method of solution is given, which is free from the previously mentioned condition. In particular, the vibrations of a triangular wing lying within the Mach cone are considered.

Description: No abstract available