ALBERT

Description: In this paper, an analytical model of a micro-electromechanical (MEM) resonator used as a 4-bit digital-to-analog converter (DAC) is presented. First, we derive the dynamic equation of the 4-bit DAC device, and the nonlinear governing equation is solved by the Galerkin method combined with a shooting technique to simulate the static response, linear eigenvalue problem, and forced vibration response of the device for various electrostatic actuation cases. Also, we optimize the air gaps in the linear domain to ensure enhanced performance of the DAC. Further, to analyze the operation of the DAC in the nonlinear regime, two experimental samples powered by −2 dBm and −12 dBm AC inputs are examined. Forward and backward frequency sweeps are conducted experimentally and analytically. The proposed analytical results are validated by comparison with experimental data. The results indicate that the presented modeling, simulations, and optimization are effective tools for the design of MEM resonator-based circuits.

Description: In this paper, an integrated microprism matrix for light coupling and optical sensing systems is presented. The matrix was fabricated by use of controlled negative pressure glass thermal reflow process by the use of monocrystalline mold. The single glass microprism had height of 250 µm or 350 µm with base width respectively 350 µm or 500 µm. The matrix was formed by 10 × 10 microprisms with distance between the microprisms from 150 µm to 400 µm. It corresponded to total area of the matrixes from 28 mm2 to 74 mm2. The controlled coupling of the beam into a substrate was obtained through determination of optimal geometric dimensions of microprisms and configuration of a measurement setup. Optimal position of the fluorescence induction light source in relation to the matrixes (0.5 cm to 4.5 cm distance, 30° angle of incidence) and microfluidic channel (4 mm) were determined. The fluorimetric tests (with excitation by 470 nm laser diode in all the experiments) carried out using fluorescein solution, microbeads and porcine oocyte indicated the possibility of using a microprism matrix for fluorimetric image-based 500 nm long-pass detection in lab-on-a-chip platforms.

Description: Neutron radiation induces point defects and affects the diffusivity of atoms and the kinetics of precipitation. The phase-field simulation reveals the influence of migration energy of vacancy on the radiation-enhanced precipitation in Fe–Cu alloy. The study shows that radiation-enhanced diffusion (RED) also depends on the diffusivity of vacancy-associated migration energy and not only on the dose rate; the low migration energy of vacancy results in accelerated precipitation and a higher volume fraction of Cu precipitates. Interestingly, decreasing migration energy from 1.0 eV to 0.9 eV results in a 30% increase in the precipitates’ volume fraction. Also, the combination of the lowest dose rate 5.0 × 10−3 dpa s−1 and highest migration energy 1.0 eV delays the precipitation. The study also examines the influence of migration energy of vacancy on the radius of Cu precipitates. The lowest migration energy, 0.9 eV, increases the radius up to one-third. Finally, the work presents the drawbacks of the analytical digital image processing technique in the quantitative comparison with the script.

Description: This paper presents a molecular structure-informed viscoelastic constitutive equation that adopts the Doi-Edward’s tube model with coarse-grained molecular dynamics (MD) simulation and primitive path analysis. Since this model contains polymer physics-related parameters directly obtained from molecular simulations, it can reflect molecular information in predictions of the viscoelastic behavior of elastomers, unlike other empirical models. The proposed incremental formulations and constitutive stiffness matrix were implemented into implicit finite element analysis (FEA) codes as a user-supplied material model and viscoelastic properties (storage, loss modulus, and tan⁡δ) were calculated from the constitutive equation. While obtaining polymer dynamics parameter of the molecular system, a relationship between self-diffusivity coefficient (D_c) and the polymerization degree of the polymer was confirmed. Furthermore, a series of parametric studies showed that increase of the primitive path length (L) and decrease of D_c have led to the strengthening of moduli and decrease of tan⁡δ peak. Moreover, under the same condition, the shift of tan⁡δ peak to low-frequency domain was observed, which implies a decline in free volume in the molecular system and an increase in the glass transition temperature.

Description: Thickness-shear (TSh) vibration of a rectangular piezoelectric crystal plate is studied with the consideration of flexoelectric effect in this paper. The developed theoretical model is based on the assumed displacement function which includes the anti-symmetric mode through thickness and symmetric mode in length. The constitutive equation with flexoelectricity, governing equations and boundary conditions are derived from the Gibbs energy density function and variational principle. For the effect of flexoelectricity, we only consider the shear strain gradient in the thickness direction so as to simply the mathematical model. Thus, two flexoelectric coefficients are used in the present model. The electric potential functions are also obtained for different electric boundary conditions. The present results clearly show that the flexoelectric effect has significant effect on vibration frequencies of thickness-shear modes of thin piezoelectric crystal plate. It is also found that the flexoelectric coefficients and length to thickness ratio have influence on the thickness-shear modes. The results tell that flexoelectricity cannot be neglected for design of small size piezoelectric resonators.

Description: The pressure and temperature inside the tire is mainly monitored by the tire pressure monitoring system (TPMS). In order to improve the integration of the TPMS system, moreover enhance the sensitivity and temperature-insensitivity of pressure measurement, this paper proposes a microelectromechanical (MEMS) chip-level sensor based on stress-sensitive aluminum-silicon hybrid structures with amplified piezoresistive effect and temperature-dependent aluminum-silicon hybrid structures for hardware and software temperature compensations. Two types of aluminum-silicon hybrid structures are located inside and outside the strained menbrane to simultaneously realize the measurement of pressure and temperature. The model of this composite sensor chip is firstly designed and verified for its effectiveness by using finite element numerical simulation, and then it is fabricated based on the standard MEMS process. The experiments indicate that the pressure sensitivity of the sensor is between 0.126 mV/(V·kPa) and 0.151 mV/(V·kPa) during the ambient temperature ranges from -20 ℃ to 100 ℃, while the measurement error, sensitivity and temperature coefficient of temperature-dependent hybrid structures are individually ± 0.91℃, -1.225 mV/(V·℃) and -0.150%/℃. The thermal coefficient of offset (TCO) of pressure measurement can be reduced from -3.553%FS/℃ to -0.375%FS/℃ based on the differential output of the proposed sensor. In order to obtain the better performance of temperature compensation, Elman neural network based on ant colony algorithm is applied in the data fusion of differential output to further eliminate the temperature drift error. Based on which, the overall measured error is within 3.45 kPa, which is less than ±1.15%FS. The thermal coefficient of offset (TCO) is -0.017%FS/℃, and the thermal coefficient of span (TCS) is -0.020%/FS℃. The research results may provide a useful reference for the development of the high-performance MEMS composite sensor for the TPMS system.

Description: In this study, the hot tensile test was carried out using the extruded and annealed Mg-1Al-6Y alloy. The effect of temperature and strain rate on the hot tensile deformation behavior of the alloy was systematically studied at different temperatures (200 ℃ ~ 350 ℃) and different strain rates (8×10-5 s-1 ~ 1.6×10-3 s-1). In addition, the effect of temperature on the evolution of microstructure when the strain rate is 1.6×10-3 s-1 was investigated. The results showed that as the temperature increased or the strain rate decreased, the peak stress decreased and the elongation increased. Hot tensile at different temperatures all increased the texture intensity, and the microstructure after deformation showed obvious characteristics of basal fiber texture ([0001]⊥ED). Correspondingly, the weaker [-15-40]//ED texture before deformation transformed into a stronger [01-10]//ED fiber texture. After deformation, the average Schmid factor (SF) of each non-basal slip was significantly increased compared with the average SF before deformation, indicating that abundant non-basal slip was activated during the deformation. When the deformation temperature was 300 °C, dynamic recrystallization (DRX) occurred significantly, and the DRXed grains accounted for 15.9%. DRX was a combination of continuous dynamic recrystallization (CDRX) and discontinuous dynamic recrystallization (DDRX). Furthermore, the calculated activation energy of the alloy was about 98.8 kJ/mol. Comprehensive research showed that the hot tensile deformation mechanism mainly included intragranular slip, grain boundary slip (GBS) and DRX.

Description: Lead-free or low lead content perovskite materials are explored in photovoltaic devices to mitigate the challenges of toxic lead-based halides. However, the conversion efficiency from such materials is far below compared to its counterparts. Therefore, to make a humble contribution in the development of lead-free or low lead content perovskite solar cells (PSCs) for future thin-film photovoltaic (PV) technology, a simulation study of tin (Sn) and Pb mixed halide (MAPb0.5Sn0.5I3, 1.22 eV) PSC is carried out in this manuscript. The device is further optimized in terms of transport layer and thickness variation to get 15.1% conversion efficiency. Moreover, the optimized narrow bandgap halide (NBH) based device is further deployed in the monolithic tandem configuration with lead-free wide bandgap (1.82 eV) halide, i.e., Cs2AgBi0.75Sb0.25Br6, 1.82eV (WBH) PSC, to mitigate the thermalization as well as transparent Eg losses. Filtered spectrum, current matching, and construction of tandem J-V curve at the current matching point are utilized to design the tandem solar cell under consideration. Tandem device delivered short current density, JSC (15.21 mA.cm-2), open-circuit voltage, VOC (1.95 V), fill factor, FF (74.09 %) and power conversion efficiency, PCE (21.97%). The performance of the devices considered in this work is found to be in good approximation with experimental work.

Description: Due to their large deformation, high energy density, and high compliance, dielectric elastomer actuators (DEAs) have found a number of applications in several areas of mechatronics and robotics. Among the many types of DEAs proposed in the literature, rolled DEAs (RDEAs) represent one of the most popular configurations. RDEAs can be effectively used as compact muscle-like actuators for soft robots, since they allow eliminating the need for external motors or compressors while providing at the same time a flexible and lightweight structure with self-sensing capabilities. To effectively design and control complex RDEA-driven systems and robots, accurate and numerically efficient mathematical models need to be developed. In this work, we propose a novel lumped-parameter model for silicone-based, thin and tightly rolled DEAs. The model is grounded on a free-energy approach, and permits to describe the electro-mechanically coupled response of the transducer with a set of nonlinear ordinary differential equations. After deriving the constitutive relationships, the model is validated by means of an extensive experimental campaign, conducted on three RDEA specimens having different geometries. It is shown how the developed model permits to accurately predict the effects of several parameters (external load, applied voltage, actuator geometry) on the RDEA electro-mechanical response, while maintaining an overall simple mathematical structure.