ALBERT

Description: Integrated computational materials techniques that span the atomistic and continuum scales have the potential to aid the design and manufacturing of thermal protection materials. Two cases demonstrating the practical application of these methods are discussed. Case one examines the selection of a high temperature coating for carbon/carbon, with the target application being a solar thermal propulsion heat exchanger. The performance of various refractory metal and metal-carbide coatings is characterized considering extreme thermal (3500 degrees Kelvin) and chemical (hydrogen flows) conditions. The recession rate, hydrogen leakage, and likelihood of mechanical failure are characterized and provide directions for further experimental investigation. Case two examines the process optimization of a heat shield material composed of a woven silica fiber preform and cyanate ester resin. Frequently, internal voids were found to be present in this composite after the resin infusion and curing stages of manufacturing. Using the manufacturing conditions, computations indicate that both water adsorption and resin cure shrinkage are contributing factors to void formation. The results suggest an alternative process configuration for curing that would mitigate voids.

Description: This presentation will update the community on the development of conformal ablative TPS. As described at IPPW-10, in FY12, the CA-TPS element focused on establishing materials requirements based on MSL-type and COTS Low Earth orbit (LEO) conditions (q 250 Wcm2) to develop and deliver a conformal ablative TPS. This involved downselecting, manufacturing and testing two of the best candidate materials, demonstrating uniform infiltration of resins into baseline 2-cm thick carbon felt, selecting a primary conformal material formulation based on novel arc jet and basic material properties testing, developing and demonstrating instrumentation for felt-based materials and, based on the data, developing a low fidelity material response model so that the conformal ablator TPS thickness for missions could be established. In addition, the project began to develop Industry Partnerships. Since the nominal thickness of baseline carbon felts was only 2-cm, a partnership with a rayon felt developer was made in order to upgrade equipment, establish the processes required and attempt to manufacture 10-cm thick white goods. A partnership with a processing house was made to develop the methodology to carbonize large pieces of the white goods into 7.5-cm thick carbon felt.In FY13, more advanced testing and modeling of the downselected conformal material was performed. Material thermal properties tests and structural properties tests were performed. The first 3 and 4-point bend tests were performed on the conformal ablator as well as PICA for comparison and the conformal ablator had outstanding behavior compared to PICA. Arc jet testing was performed with instrumented samples of both the conformal ablator and standard PICA at heating rates ranging from 40 to 400 Wcm2 and shear as high as 600 Pa. The results from these tests showed a remarkable improvement in the thermal penetration through the conformal ablator when compared to PICAs response. The data from these tests were used to develop a mid-fidelity thermal response model. Additional arc jet testing in the same conditions on various seam designs were very successful in showing that the material could be joined with a minimum of adhesive and required no complicated gap and gap filler design for installation. In addition, the partnership with industry to manufacture thicker rayon felt was very successful. The vendor made a 2-m wide by 30-m long sample of 10-cm thick rayon felt. When carbonized, the resulting thickness was over 7.5-cm thick, nearly 4 times the thickest off-the-shelf carbon felt. In FY14, the project has initiated a partnership with another vendor to begin the scale-up manufacturing effort. This year, the vendor will duplicate the process and manufacture at the current scale for comparison with NASA-processed materials. Properties testing and arc jet testing will be performed on the vendor-processed materials. Planning for manufacturing large, 1-m x 1-m, panels will begin as well. In FY15, the vendor will then manufacture large panels and the project will build a 2-m x 2-m Manufacturing Demonstration Unit (MDU).

Description: Hafnium diboride-silicon carbide and zirconium diboride-silicon carbide composites are potential materials for high temperature leading edge applications on reusable launch vehicles. In order to establish material constants necessary for evaluation of in-situ fracture, bars fractured in four point flexure were examined using fractographic principles. The fracture toughness was determined from measurements of the critical crack sizes and the strength values, and the crack branching constants were established to use in forensic fractography of materials for future flight applications. The fracture toughnesses range from about 13 MPam (sup 1/2) at room temperature to about 6 MPam (sup 1/2) at 1400 C for ZrB2-SiC composites and from about 11 MPam (sup 1/2) at room temperature to about 4 MPam (sup 1/2) at 1400 C for HfB2-SiC composites.

Description: HfB2 and ZrB2 composites containing SiC are known to have good thermal shock and configurational stability at elevated temperatures. These are promising ultra-high temperature ceramics (UHTCs) for use on the sharp leading edges of next generation space vehicles. Sharp leading edges on these vehicles will need to: withstand repeated exposures to temperatures 〉 2200 C in oxidizing environments; have good thermal shock and ablation resistance; and withstand the mechanical stress of launch and reentry. The HfB2/SiC composite is currently undergoing processing improvements in an effort to better the performance of a material that has been studied for approx. 35 years. The potential for HfB2/SiC composites to meet the requirements of hypersonic flight depends on controlling processing techniques. This presentation will focus on understanding processing steps now being undertaken to optimize the material properties of HfB2/SiC composites at NASA Ames Research Center. Correlation between processing techniques and microstructure will be shown. Preliminary oxidation studies will also be discussed.

Description: Previous work on refractory diboride composites has shown that these systems have the potential for use in high temperature leading edge applications for reusable reentry vehicles. Experiments in reentry environments have shown that these materials have multiple use temperatures greater than 1900 C. The work to be discussed focuses on three compositions: HfB2/SiC, ZrB2/SiC, and ZrB2/C/SiC. These composites have been hot pressed and their mechanical properties measured at room and elevated temperatures. Extensive microstructural characterization has been conducted on polished cross sections and the fracture surfaces have been examined to determine their failure origins.

Description: Materials with improved properties are needed for thermal protection of next generation space vehicles. Sharp leading edges on these vehicles will have to withstand exposure to high temperatures (〉 2200 C or 4000 F) and severe thermal cycling in both neutral and oxidizing environments. These extreme conditions will require materials that possess superior oxidation resistance, low creep, and excellent thermal shock properties. This presentation will first discuss the system requirements for thermal protection of advanced space vehicles and then show how they are driving development of new materials systems. The presentation will focus on ultrahigh temperature ceramics (UHTCs) that are promising candidates for such applications. ZrB2 and HfB2 and composites of those ceramics with SiC are two particular families of UHTCs that are currently under development for sharp leading edges. These ceramics are appealing because their melting temperatures are 3245 C (5873 F) for ZrB2 and 3380 C (6116 F) for HfB2 and because they may form protective, oxidation resistant coatings in use. The mechanical properties of the UHTCs are strongly dependent on phase purity and the processing route used to make them, both of which factors are being actively investigated. For example, oxide impurities could form glassy grain boundary phases that soften at high temperatures and make the ceramic susceptible to creep deformation. Results from scanning and transmission electron microscopic studies of the UHTCs have shown how their processing can be improved to give better properties. This presentation will discuss the UHTC characterization results in some detail, focusing particularly on the structure and composition of the ceramic grain boundaries. The presentation will conclude with some remarks on how the properties of these promising UHTCs can be further improved and how they might be made more economically.

Description: Conformable Phenolic Impregnated Carbon Ablator, a cousin of Phenolic Impregnated Carbon Ablator (PICA), was developed at NASA Ames Research Center as a lightweight thermal protection system under the Fundamental Aeronautics Program. PICA is made using a brittle carbon substrate, which has a very low strain to failure. Conformable PICA is made using a flexible carbon substrate, a felt in this case. The flexible felt significantly increases the strain to failure of the ablator. PICA is limited by its thermal mechanical properties. Future NASA missions will require heatshields that are more fracture resistant than PICA and, as a result, NASA Ames is working to improve PICAs performance by developing conformable PICA to meet these needs. Research efforts include tailoring the chemistry of conformable PICA with varying amounts of additives to enhance mechanical properties and testing them in aerothermal environments. This poster shows the performance of conformable PICA variants in arc jets tests. Some mechanical and thermal properties will also be presented.

Description: High temperature testing of thermal protection system (TPS) materials is a critical aspect of heat-shield materials development, as it determines the suitability and performance envelope of the materials. The present talk provides an overview of recent updates to NASAs IHF and AEDCs H3 high temperature arcjet test facilities that to enable higher heat flux (5000-8000 Wcm2) and high pressure (5-14 atm) testing of TPS. Some recent thermal tests of fully dense carbon phenolic will be discussed in this paper. These new facility upgrades will help improve the TRL level of novel TPS materials and will help qualifycertify heritage TPS material candidates for future missions that are expected to encounter extreme entry conditions, such as entry into Venus or Saturn.

Description: The testing of a thermal protection system (TPS) in multiple arc jets and laser facilities is critical not only to determine the ability of a material to withstand the harsh aerothermal environments but is also required to collect relevant data that allows construction of a thermal response model of the TPS for flight design. The present talk provides an overview of recent arcjet testing of the HEEET material, one of the families of materials from the 3D Woven TPS program, being developed under NASAs Heatshield for Extreme Entry Environment Technology (HEEET) project.