ALBERT

Description: 〈p〉Publication date: Available online 8 July 2019〈/p〉 〈p〉〈b〉Source:〈/b〉 International Journal of Hydrogen Energy〈/p〉 〈p〉Author(s): Muhammad Abid, Muhammad Sajid Khan, Tahir Abdul Hussain Ratlamwala〈/p〉 〈div xml:lang="en"〉 〈h5〉Abstract〈/h5〉 〈div〉〈p〉Parabolic dish solar collector system has capability to gain higher efficiency by converting solar radiations to thermal heat due to its higher concentration ratio. This paper examines the exergo-economic analysis, net work and hydrogen production rate by integrating the parabolic dish solar collector with two high temperature supercritical carbon dioxide (s-CO〈sub〉2〈/sub〉) recompression Brayton cycles. Pressurized water (H〈sub〉2〈/sub〉O) is used as a working fluid in the solar collector loop. The various input parameters (direct normal irradiance, ambient temperature, inlet temperature, turbine inlet temperature and minimum cycle temperature) are varied to analyze the effect on net power output, hydrogen production rate, integrated system energetic and exergetic efficiencies. The simulations has been carried out using engineering equation solver (EES). The outputs demonstrate that the net power output of the integrated reheat recompression s-CO〈sub〉2〈/sub〉 Brayton system is 3177 kW, whereas, without reheat integrated system has almost 1800 kW net work output. The overall energetic and exergetic efficiencies of former system is 30.37% and 32.7%, respectively and almost 11.6% higher than the later system. The hydrogen production rate of the solarized reheat and without reheat integrated systems is 0.0125 g/sec and 0.007 g/sec, accordingly and it increases with rise in direct normal irradiance and ambient temperature. The receiver has the highest exergy destruction rate (nearly 44%) among the system components. The levelized electricity cost (LEC) of 0.2831 $/kWh with payback period of 9.5 years has proved the economic feasibility of the system design. The increase in plant life from 10 to 32 years with 8% interest rate will decrease the LEC from (0.434-0.266) $/kWh. Recuperators have more potential for improvement and their cost rate of exergy is higher as compared to the other components.〈/p〉〈/div〉 〈/div〉

Description: 〈p〉Publication date: Available online 8 July 2019〈/p〉 〈p〉〈b〉Source:〈/b〉 International Journal of Hydrogen Energy〈/p〉 〈p〉Author(s): Yuan Xue, Shixiong Min, Fang Wang〈/p〉 〈div xml:lang="en"〉 〈h5〉Abstract〈/h5〉 〈div〉〈p〉Although black phosphorous (BP) and its derived materials have shown great potential for application in photocatalytic H〈sub〉2〈/sub〉 evolution reaction (HER), their HER activity and stability still remains unsatisfied mainly due to the insufficient charge separation, the lack of surface active sites, and the defect-riched nature of BP. Herein, we report that BP nanosheets decorated with in situ grown Pt (BP NSs/Pt) could act as a highly efficient catalyst for photocatalytic H〈sub〉2〈/sub〉 evolution in an Erythrosin B (ErB)-sensitized system under visible light irradiation (≥450 nm) in the presence of triethanolamine (TEOA) as sacrificial electron donor. It is found that BP NSs can provide large surface area for the confined growth of Pt nanoparticles with a high dispersion and a reduced size but also stabilize the loaded Pt nanoparticles by covalent bonds at the BP NSs/Pt interfaces. Moreover, BP NSs offer a fast electron transfer pathway to facilitate the photocatalytic HER over in situ grown Pt catalyst. As a result, BP NSs/Pt catalyst exhibits ∼6 times higher H〈sub〉2〈/sub〉 evolution activity than free Pt nanoparticles and an apparent quantum yield (AQY) of 0.57% at 500 nm irradiation in ErB-TEOA system. This work indicates the potential of BP NSs as an effective 2D matrix to construct numerous high performance photocatalysts and photocatalytic systems.〈/p〉〈/div〉 〈/div〉

Description: 〈p〉Publication date: Available online 8 July 2019〈/p〉 〈p〉〈b〉Source:〈/b〉 International Journal of Hydrogen Energy〈/p〉 〈p〉Author(s): C. Juillet, M. Tupin, F. Martin, Q. Auzoux, C. Berthinier, F. Miserque, F. Gaudier〈/p〉 〈div xml:lang="en"〉 〈h5〉Abstract〈/h5〉 〈div〉〈p〉Under Pressurized Water Reactor normal operating conditions, the external surface of zirconium alloys cladding absorbs a fraction of the hydrogen produced by water reduction. During spent fuel transport, hydrogen may desorb from the cladding. The study aims to identify and quantify the rate-limiting step in the hydrogen desorption process initially present in the alloy. To better understand this process, the Thermal Desorption Spectrometry (TDS) was used in association with X-ray Photoelectron Spectroscopy analysis. TDS results were analysed with finite elements simulations using the Cast3M code. The optimization of the kinetic constants of hydrogen desorption was performed with CEA (Alternative Energies and Atomic Energy Commission)-tool URANIE. Results showed that hydrogen desorption kinetics from the metal is limited by the surface molecular recombination. Arrhenius-type temperature dependence of kinetic constants allowed to simulate experimental data with a good agreement. The optimized activation energy and the pre-exponential factor for desorption processes were in the range of 290 ± 10 kJ mol〈sup〉−1〈/sup〉 and 3 × 10〈sup〉7〈/sup〉 m〈sup〉4〈/sup〉 mol〈sup〉−1〈/sup〉 s〈sup〉−1〈/sup〉 respectively.〈/p〉〈/div〉 〈/div〉

Description: 〈p〉Publication date: Available online 8 July 2019〈/p〉 〈p〉〈b〉Source:〈/b〉 International Journal of Hydrogen Energy〈/p〉 〈p〉Author(s): Abhishek Rajput, Prem P. Sharma, Vikrant Yadav, Vaibhav Kulshrestha〈/p〉 〈div xml:lang="en"〉 〈h5〉Abstract〈/h5〉 〈div〉〈p〉Proton exchange membrane is a basic element for any redox flow battery. Nafion is the only commercial available proton exchange membrane used in different electro-chemical energy systems. High cost restrict it's used for energy generation devices. In present work, we synthesised styrene divinylbenzene based composite proton exchange membranes (PEMs) with varying sulfonated graphene oxide (sGO) content for redox flow battery (RFB). Synthesized copolymer PEMs were analyzed in terms of their chemical structure with the help of FT-IR spectroscopy to confirm desired functional groups at appropriate position. Electrochemical characterization was performed in terms proton-exchange capacity, protonic conductivity and water uptake. Membrane shows adequate proton exchange capacity with good proton conductivity. Vanadium ion permeability was also tested for the prepared membrane to assess capability for vanadium redox flow battery (VRFB) in contrast with commercially available Nafion 117 PEM. Higher VO〈sup〉+2〈/sup〉 ion cross-over resistance was found for CEM-4 with 7.17 × 10〈sup〉−7〈/sup〉 cm〈sup〉2〈/sup〉 min〈sup〉−1〈/sup〉 permeability, which is about half of the CEM-1. Further CEM-4 was also evaluated for charging-discharging phenomenon for single cell VRFB. The values of columbic, voltage and energy efficiency for VRFB confirms prepared membrane as a good candidate for redox flow battery. Composite PEM also shows better mechanical and thermal stability. Results indicates that synthesized composite membrane can be used in vanadium redox flow battery.〈/p〉〈/div〉 〈/div〉 〈h5〉Graphical abstract〈/h5〉 〈div〉〈p〉〈figure〉〈img src="https://ars.els-cdn.com/content/image/1-s2.0-S0360319919323584-fx1.jpg" width="395" alt="Image 1" title="Image 1"〉〈/figure〉〈/p〉〈/div〉

Description: 〈p〉Publication date: 1 November 2019〈/p〉 〈p〉〈b〉Source:〈/b〉 Solid State Ionics, Volume 340〈/p〉 〈p〉Author(s): Ananda Shastri, Deborah Watson, Qing-Ping Ding, Yuji Furukawa, Steve W. Martin〈/p〉 〈div xml:lang="en"〉 〈h5〉Abstract〈/h5〉 〈div〉〈p〉〈sup〉23〈/sup〉Na NMR spin lattice relaxation times, T〈sub〉1〈/sub〉, and central linewidths were obtained for yNa〈sub〉2〈/sub〉S + (1 − y)[xSiS〈sub〉2〈/sub〉 + (1 − x)PS〈sub〉5/2〈/sub〉] glassy solid electrolytes for two series of glasses, y = 0.5 and 0.67, and x = 0.1, 0.3, 0.5, 0.7, and 0.9. No pronounced mixed glass former effect in the activation energy was observed within experimental uncertainty for either series of glasses. Energy barriers to sodium motion were calculated using the Anderson-Stuart model for the y = 0.67 sample, and the results suggested that the energy barriers as a function of composition are strongly influenced by the dielectric constant of these glasses. DC Na〈sup〉+〈/sup〉 ion conductivity values calculated using NMR-derived correlation times, an available Na〈sup〉+〈/sup〉 ion site coordination number in the range z = 3–4, and an energy cutoff determined from the critical percolation threshold, were in agreement with the increasing trend in the experimental values for the y = 0.67 glasses. Using the same model, the conductivity values were calculated for the y = 0.50 glasses, which have as yet to be measured, and these revealed a decreasing conductivity as x increased. Sodium NMR second moment studies showed that the cation spatial arrangement followed a homogeneous distribution for y = 0.50 and 0.67 samples over most of the composition range, but deviated significantly away from this above a sodium concentration of 1.85 × 10〈sup〉28〈/sup〉 m〈sup〉-3〈/sup〉, suggesting a tendency for sodium to cluster under these conditions.〈/p〉〈/div〉 〈/div〉

Description: 〈p〉Publication date: 10 November 2019〈/p〉 〈p〉〈b〉Source:〈/b〉 Science of The Total Environment, Volume 690〈/p〉 〈p〉Author(s): Marie-Ange Massicotte, Antony T. Vincent, Anna Schneider, Valérie E. Paquet, Michel Frenette, Steve J. Charette〈/p〉 〈div xml:lang="en"〉 〈h5〉Abstract〈/h5〉 〈div〉〈p〉The Gram-negative bacterium 〈em〉Aeromonas salmonicida〈/em〉 subsp. 〈em〉salmonicida〈/em〉 is an aquatic pathogen which causes furunculosis to salmonids, especially in fish farms. The emergence of strains of this bacterium exhibiting antibiotic resistance is increasing, limiting the effectiveness of antibiotherapy as a treatment against this worldwide disease. In the present study, we discovered an isolate of 〈em〉A. salmonicida〈/em〉 subsp. 〈em〉salmonicida〈/em〉 that harbors two novel plasmids variants carrying antibiotic resistance genes. The use of long-read sequencing (PacBio) allowed us to fully characterize those variants, named pAsa5-3432 and pRAS3-3432, which both differ from their classic counterpart through their content in mobile genetic elements. The plasmid pAsa5-3432 carries a new multidrug region composed of multiple mobile genetic elements, including a Class 1 integron similar to an integrated element of 〈em〉Salmonella enterica〈/em〉. With this new region, probably acquired through plasmid recombination, pAsa5-3432 is the first reported plasmid of this bacterium that bears both an essential virulence factor (the type three secretion system) and multiple antibiotic resistance genes. As for pRAS3-3432, compared to the classic pRAS3, it carries a new mobile element that has only been identified in 〈em〉Chlamydia suis〈/em〉. Hence, with the identification of those two novel plasmids harboring mobile genetic elements that are normally encountered in other bacterial species, the present study puts emphasis on the important impact of mobile genetic elements in the genomic plasticity of 〈em〉A. salmonicida〈/em〉 subsp. 〈em〉salmonicida〈/em〉 and suggests that this aquatic bacterium could be an important reservoir of antibiotic resistance genes that can be exchanged with other bacteria, including human and animal pathogens.〈/p〉〈/div〉 〈/div〉 〈div xml:lang="en"〉 〈h5〉Graphical abstract〈/h5〉 〈div〉〈p〉〈figure〉〈img src="https://ars.els-cdn.com/content/image/1-s2.0-S0048969719330293-ga1.jpg" width="500" alt="Unlabelled Image" title="Unlabelled Image"〉〈/figure〉〈/p〉〈/div〉 〈/div〉

Description: 〈p〉Publication date: 1 November 2019〈/p〉 〈p〉〈b〉Source:〈/b〉 Science of The Total Environment, Volume 689〈/p〉 〈p〉Author(s): Christopher Markosian, Natella Mirzoyan〈/p〉 〈div xml:lang="en"〉 〈h5〉Abstract〈/h5〉 〈div〉〈p〉Pollution by heavy metals and metalloids is detrimental to human health due to their toxic, genotoxic, and carcinogenic effects. The traditional approach to assess the extent of environmental and occupational exposures of metals is human biomonitoring (HBM). This method has several limitations, including invasiveness, sampling bias, cost- and time-intensiveness, and ethical issues. This suggests the need for a more robust, non-invasive, epidemiological tool for assessment of exposure to metals and their public health effects. Recently, wastewater-based epidemiology (WBE) has been suggested and utilized as a novel approach to accurately determine the extent of exposure to multiple substances on the population level. We suggest the potential application of WBE to the study of metal exposure on the population level, including possible biomarkers for wastewater analysis of 10 metals belonging to three categories according to health effects and nutritional benefits, and its public health implications. Similar to previous studies of exposure to regulated or illegal drugs, unregulated legal substances, and pesticides, WBE can be applied to the study of metal exposure in a given community. Parental substance biomarkers (PSBs), metabolic substance biomarkers (MSBs), and non-substance biomarkers (NSBs) of 10 common metals are available for consideration in wastewater analysis. The use of WBE would allow for the interpretation of the relationship between metal exposure and population health, reveal synergistic effects of different health factors, and model public health risks under different scenarios.〈/p〉〈/div〉 〈/div〉 〈div xml:lang="en"〉 〈h5〉Graphical abstract〈/h5〉 〈div〉〈p〉〈figure〉〈img src="https://ars.els-cdn.com/content/image/1-s2.0-S0048969719329924-ga1.jpg" width="459" alt="Unlabelled Image" title="Unlabelled Image"〉〈/figure〉〈/p〉〈/div〉 〈/div〉

Description: 〈p〉Publication date: 10 November 2019〈/p〉 〈p〉〈b〉Source:〈/b〉 Science of The Total Environment, Volume 690〈/p〉 〈p〉Author(s): Yong-Lin Liu, Yong-Tao Li, Jian-Fei Huang, Yu-Long Zhang, Zhong-Hang Ruan, Tian Hu, Jin-Jin Wang, Wen-Yan Li, Han-Jian Hu, Gang-Biao Jiang〈/p〉 〈div xml:lang="en"〉 〈h5〉Abstract〈/h5〉 〈div〉〈p〉The application of iron oxide nanoparticles (IONs) is often limited by agglomeration and low loading. Here, we presented a facile phase change material (PCM) -based sol-gel strategy for the fabrication of α-Fe〈sub〉2〈/sub〉O〈sub〉3〈/sub〉 nanoparticles. Rosin was used as the PCM in the sol-gel process and the carbon-based substrate of α-Fe〈sub〉2〈/sub〉O〈sub〉3〈/sub〉 nanoparticles in the thermal process. The α-Fe〈sub〉2〈/sub〉O〈sub〉3〈/sub〉 nanoparticle embedded rosin-derived biochar(α-Fe〈sub〉2〈/sub〉O〈sub〉3〈/sub〉@HrBc)were highly dispersed. The dispersity of α-Fe〈sub〉2〈/sub〉O〈sub〉3〈/sub〉 nanoparticle could be regulated by the weight ratios of rosin to FeCl〈sub〉3〈/sub〉·6H〈sub〉2〈/sub〉O during the preparation, as evidenced by the scanning electron microscope (SEM) spectrum and the sorption capacity results. Among a series of α-Fe〈sub〉2〈/sub〉O〈sub〉3〈/sub〉@HrBc nanocomposites, the one with the weight ratios of 1/1.5 rosin/FeCl〈sub〉3〈/sub〉·6H〈sub〉2〈/sub〉O had the highest capacity for hexavalent chromium (Cr(VI)) sorption. This phenomenon can be ascribed to a remarkably enhanced interfacial reactivity due to an increase in the dispersity of α-Fe〈sub〉2〈/sub〉O〈sub〉3〈/sub〉 nanoparticle. In addition, SEM showed that the majority of α-Fe〈sub〉2〈/sub〉O〈sub〉3〈/sub〉 nanoparticles was dispersed on and inside the biochar substrate. Batch adsorption experiments revealed that the α-Fe〈sub〉2〈/sub〉O〈sub〉3〈/sub〉@HrBc adsorbed 90% Cr(VI) within one minute, and the maximum capacity was up to 166 mg·g〈sup〉−1〈/sup〉 based on the Langmuir model. The FTIR and XPS spectra revealed that the adsorbed Cr(VI) species were partially reduced to less toxic Cr(III). Considering that α-Fe〈sub〉2〈/sub〉O〈sub〉3〈/sub〉 nanoparticles provided important sorption sites, the newly formed Cr(III) and the remaining Cr(VI) ions could be adsorbed on α-Fe〈sub〉2〈/sub〉O〈sub〉3〈/sub〉@HrBc via the formation of Fe〈img src="https://sdfestaticassets-eu-west-1.sciencedirectassets.com/shared-assets/16/entities/sbnd"〉Cr coprecipitation.〈/p〉〈/div〉 〈/div〉 〈div xml:lang="en"〉 〈h5〉Graphical abstract〈/h5〉 〈div〉〈p〉〈figure〉〈img src="https://ars.els-cdn.com/content/image/1-s2.0-S0048969719331341-ga1.jpg" width="351" alt="Unlabelled Image" title="Unlabelled Image"〉〈/figure〉〈/p〉〈/div〉 〈/div〉

Description: 〈p〉Publication date: 1 November 2019〈/p〉 〈p〉〈b〉Source:〈/b〉 Science of The Total Environment, Volume 689〈/p〉 〈p〉Author(s): Lei Zhang, Zhen Shen, Wangkai Fang, Guang Gao〈/p〉 〈div xml:lang="en"〉 〈h5〉Abstract〈/h5〉 〈div〉〈p〉Efforts to understand the environmental and biological factors that influence the dynamics of microbial communities have received substantial attention in microbial ecology. In this study, Illumina MiSeq high-throughput sequencing technology was used to examine the microbial community structure of activated sludge in municipal wastewater treatment systems (Chuzhou city, China). Overall, 〈em〉Proteobacteria〈/em〉, 〈em〉Chloroflexi〈/em〉, 〈em〉Actinobacteria〈/em〉, 〈em〉Acidobacteria〈/em〉, 〈em〉Actinobacteria〈/em〉, 〈em〉Bacteroidetes〈/em〉, and 〈em〉Firmicutes〈/em〉 were the most dominant phyla in the five activated sludge samples. However, the community structure of nitrifying bacteria was relatively simple, and diversity was low; only AOB (〈em〉Nitrosomonas〈/em〉) and NOB (〈em〉Nitrospira〈/em〉) were detected. The dominant bacteria in the anaerobic sludge, anoxic sludge and oxic sludge were the same, and each bacterial species was relatively uniform, with differences only in proportions. Redundancy analysis indicated that pH, TP and COD were strong environmental factors influencing the bacterial community distribution. PICRUSt was used to describe the metabolic and functional abilities of the activated sludge bacterial communities. The results emphasized the vast genetic diversity of these organisms, which are involved in various essential processes such as amino acid transport and metabolism, energy production and conversion, cell wall/membrane/envelope/biogenesis, signal transduction mechanisms, and carbohydrate transport and metabolism. Activated sludge of municipal wastewater treatment systems can be ranked in the following order based on the 16S rRNA gene copy numbers of the detected phylotypes: S1 〉 S2 〉 S4 〉 S5 〉 S3. This study provides basic data and a theoretical analysis of the optimal design and operation in wastewater treatment plants.〈/p〉〈/div〉 〈/div〉 〈div xml:lang="en"〉 〈h5〉Graphical abstract〈/h5〉 〈div〉〈p〉〈figure〉〈img src="https://ars.els-cdn.com/content/image/1-s2.0-S0048969719330050-ga1.jpg" width="285" alt="Unlabelled Image" title="Unlabelled Image"〉〈/figure〉〈/p〉〈/div〉 〈/div〉

Description: 〈p〉Publication date: 10 November 2019〈/p〉 〈p〉〈b〉Source:〈/b〉 Science of The Total Environment, Volume 690〈/p〉 〈p〉Author(s): Zhanfei He, Qingying Zhang, Zhen Wei, Yuanhai Zhao, Xiangliang Pan〈/p〉 〈div xml:lang="en"〉 〈h5〉Abstract〈/h5〉 〈div〉〈p〉Organic micropollutants (OMPs) are frequently detected in water and wastewater, and have attracted wide attention due to potential adverse effects on ecosystems and human health. In this work, manganese-oxidizing aerobic granular sludge (Mn-AGS) was successfully cultivated and applied to remove OMPs from wastewater. Biogenic manganese (III,IV) oxides (bio-MnO〈sub〉x〈/sub〉) were generated and accumulated to 22.0–28.3 mg Mn/g SS in the final sludge. Neither the addition of allochthonous manganese-oxidizing bacteria (MnOB; 〈em〉Pseudomonas putida〈/em〉 MnB1) nor the reduction in hydraulic retention time (HRT) facilitated the cultivation of Mn-AGS. Batch experiments of OMPs degradation indicated that Mn-AGS significantly improved (1.3–3.9 times) degradation rates of most OMPs. Removal rates of bisphenol A (BPA), 17α‑ethinylestradiol (EE2), tetracycline (TC), and chloramphenicol (CAP) were 3.0–12.6 μg/h/g SS by the traditional AGS and 8.0–16.3 μg/h/g SS by Mn-AGS; those of imazethapyr (IM) were relatively high, 64.7 ± 0.1 and 127.8 ± 2.5 μg/h/g SS by AGS and Mn-AGS, respectively. However, degradation of dichlorophenyl phosphine (DCPP) was slower by Mn-AGS than AGS, 9.0 ± 0.4 vs. 21.2 ± 0.9 μg/h/g SS, possibly due to inhibition of microbial activity by bio-MnO〈sub〉x〈/sub〉. This work provides a promising method for treating OMPs in organic wastewater, but the possible inhibition of microbes by bio-MnO〈sub〉x〈/sub〉 should be noted.〈/p〉〈/div〉 〈/div〉 〈div xml:lang="en"〉 〈h5〉Graphical abstract〈/h5〉 〈div〉〈p〉〈figure〉〈img src="https://ars.els-cdn.com/content/image/1-s2.0-S0048969719330827-ga1.jpg" width="301" alt="Unlabelled Image" title="Unlabelled Image"〉〈/figure〉〈/p〉〈/div〉 〈/div〉

Description: 〈p〉Publication date: 10 November 2019〈/p〉 〈p〉〈b〉Source:〈/b〉 Science of The Total Environment, Volume 690〈/p〉 〈p〉Author(s): Alexander Johs, Virginia A. Eller, Tonia L. Mehlhorn, Scott C. Brooks, David P. Harper, Melanie A. Mayes, Eric M. Pierce, Mark J. Peterson〈/p〉 〈div xml:lang="en"〉 〈h5〉Abstract〈/h5〉 〈div〉〈p〉Mercury (Hg) contamination of soils and sediments impacts numerous environments worldwide and constitutes a challenging remediation problem. In this study, we evaluate the impact of dissolved organic matter (DOM) on the effectiveness of eight sorbent materials considered for Hg remediation in soils and sediments. The materials include both engineered and unmodified materials based on carbon, clays, mesoporous silica and a copper alloy. Initially, we investigated the kinetics of Hg(II) complexation with DOM for a series of Hg:DOM ratios. Steady-state Hg-DOM complexation occurred within 48 to 120 h, taking longer time at higher Hg:DOC (dissolved organic carbon) molar ratios. In subsequent equilibrium experiments, Hg(II) was equilibrated with DOM at a defined Hg:DOC molar ratio (2.4 · 10〈sup〉−6〈/sup〉) for 170 h and used in batch experiments to determine the effect of DOM on Hg partition coefficients and sorption isotherms by comparing Hg(II) and Hg-DOM. Hg sorption capacities of all sorbents were severely limited in the presence of DOM as a competing ligand. Thiol-SAMMS®, SediMite™ and pine biochar were most effective in reducing Hg concentrations. While pine biochar and lignin-derived carbon processed at high temperatures released negligible amounts of anions into solution, leaching of sulfate and chloride was observed for most engineered sorbent materials. Sulfate may stimulate microbial communities harboring sulfate reducing bacteria, which are considered one of the primary drivers of microbial mercury methylation in the environment. The results highlight potential challenges arising from the application of sorbents for Hg remediation in the field.〈/p〉〈/div〉 〈/div〉 〈div xml:lang="en"〉 〈h5〉Graphical abstract〈/h5〉 〈div〉〈p〉〈figure〉〈img src="https://ars.els-cdn.com/content/image/1-s2.0-S0048969719331146-ga1.jpg" width="500" alt="Unlabelled Image" title="Unlabelled Image"〉〈/figure〉〈/p〉〈/div〉 〈/div〉

Description: 〈p〉Publication date: 1 November 2019〈/p〉 〈p〉〈b〉Source:〈/b〉 Science of The Total Environment, Volume 689〈/p〉 〈p〉Author(s): Min Xu, Robert D. Stedtfeld, Fang Wang, Syed A. Hashsham, Yang Song, Yahui Chuang, Jianbo Fan, Hui Li, Xin Jiang, James M. Tiedje〈/p〉 〈div xml:lang="en"〉 〈h5〉Abstract〈/h5〉 〈div〉〈p〉Different long-term fertilization regimes may change indigenous microorganism diversity in the arable soil and thus might influence the persistence and transmission of manure-born antibiotic resistance genes (ARGs). Different manure origins and composting techniques might affect the fate of introduced ARGs in farmland. A four-month microcosm experiment was performed using two soils, which originated from the same field and applied with the same chemical fertilizer or swine manure for 26 years, to investigate the dynamics of ARGs in soil amended with manure or compost from the farm and an agro-technology company. High throughput qPCR and sequencing were applied to quantify ARGs using 144 primer sets and microorganism in soil. Fertilization history had little effect on dynamics of manure-borne ARGs in soil regardless of manure origin or composting. Very different half-lives of ARGs and mobile genetic elements from farm manure and commercial manure were observed in both soils. Composting decreased abundance of most ARGs in manure, but increased the persistence of manure-introduced ARGs in soil irrespective of fertilization history, especially for those from farm manure. These findings help understanding the fate of ARGs in manured soil and may inform techniques to mitigate ARGs transmission.〈/p〉〈/div〉 〈/div〉 〈div xml:lang="en"〉 〈h5〉Graphical abstract〈/h5〉 〈div〉〈p〉〈figure〉〈img src="https://ars.els-cdn.com/content/image/1-s2.0-S0048969719329493-ga1.jpg" width="301" alt="Unlabelled Image" title="Unlabelled Image"〉〈/figure〉〈/p〉〈/div〉 〈/div〉

Description: 〈p〉Publication date: 10 November 2019〈/p〉 〈p〉〈b〉Source:〈/b〉 Science of The Total Environment, Volume 690〈/p〉 〈p〉Author(s): Md. Siddiqur Rahman, Abu Reza Md. Towfiqul Islam〈/p〉 〈div xml:lang="en"〉 〈h5〉Abstract〈/h5〉 〈div〉〈p〉A comprehensive understanding of the changing behaviors of precipitation concentration and intensity plays a pivotal role in water resource management. Hence, we investigated the spatiotemporal changing behaviors of frequency and intensity of 13 precipitation indices and their probable causes of changes in precipitation systems. This study used daily precipitation datasets from 23 sites in Bangladesh and six atmospheric circulation indices during 1975–2017. The results showed that the precipitation concentration index (LCI) varies between 0.57 and 0.63, and the highest value was found in the southeastern region. The precipitation days frequency indices such as AD, LPD, MPD, HPD, and WPD have significantly increased in Bangladesh while precipitation intensity indices such as AII, LPI, MPI, HPI, and WPI have significantly declined; all types of indices have clear rapid changes. The results of detrended fluctuation analysis (DFA) exhibit long-term correlations among all precipitation indices, suggesting that these indices will sustain their present trend line in the upcoming period. The Sunspot (SS) and East Asian Summer Monsoon Index (EASMI) had a negative influence on ACI and South Asian Summer Monsoon index (SASMI) had a strong positive influence on precipitation days frequency indices. The significance analysis using the random forest (RF) algorithm showed that SS is the largest contributing factor affecting the precipitation systems in Bangladesh. ECMWF ERA5 reanalysis datasets revealed that elevating summer geopotential height, higher anticyclonic anomaly, increasing low and decreasing high cloud covers and lower solar radiation with adequate moisture divergence fluxes contributed to variations in precipitation extremes in Bangladesh.〈/p〉〈/div〉 〈/div〉 〈div xml:lang="en"〉 〈h5〉Graphical abstract〈/h5〉 〈div〉〈p〉Linear trend of Arid days, AD (a), Sequential Mann-kendall test to detect rapid change (b), DFA long term forecasting of ACI (c) and Cross wavelet between SASMI and ACI (d).〈figure〉〈img src="https://ars.els-cdn.com/content/image/1-s2.0-S0048969719330980-ga1.jpg" width="301" alt="Unlabelled Image" title="Unlabelled Image"〉〈/figure〉〈/p〉〈/div〉 〈/div〉

Description: 〈p〉Publication date: 10 November 2019〈/p〉 〈p〉〈b〉Source:〈/b〉 Science of The Total Environment, Volume 690〈/p〉 〈p〉Author(s): Bláthnaid M. Mahon, Carina Brehony, Niamh Cahill, Elaine McGrath, Louise O'Connor, Aine Varley, Martin Cormican, Sinead Ryan, Paul Hickey, Shane Keane, Martina Mulligan, Bryan Ruane, Keith A. Jolley, Martin C. Maiden, Sylvain Brisse, Dearbháile Morris〈/p〉 〈div xml:lang="en"〉 〈h5〉Abstract〈/h5〉 〈div〉〈p〉The rapid dissemination of carbapenemase-producing 〈em〉Enterobacterales〈/em〉 (CPE) is a major public health concern. The role that the aquatic environment plays in this dissemination is underexplored. This study aimed to examine seawater as a reservoir for CPE. Seawater sampling took place at a bathing site throughout the 2017 bathing season. Each 30 L sample (〈em〉n〈/em〉 = 6) was filtered using the CapE filtration system. Wastewater samples (200 mL) (pre-treatment (〈em〉n〈/em〉 = 3) and post-treatment (n = 3)) were obtained from a nearby secondary wastewater treatment plant, during the same time period. All samples were examined for CPE. Whole genome sequencing of confirmed CPE was carried out using Illumina sequencing. Isolate genomes were hosted in corresponding BIGSdb databases and analyses were performed using multiple web-based tools. CPE was detected in 2/6 seawater samples. It was not detected in any wastewater samples. OXA-48-like-producing ST131 〈em〉Escherichia coli〈/em〉 (Ec_BM707) was isolated from a seawater sample collected in May 2017 and OXA-48-like-producing ST101 〈em〉Klebsiella pneumoniae〈/em〉 (Kp_BM758) was isolated from a seawater sample collected in August 2017. The genomes of the environmental isolates were compared to a collection of previously described Irish clinical OXA-48-like-producing 〈em〉Enterobacterales〈/em〉 (〈em〉n〈/em〉 = 105). Ec_BM707 and Kp_BM758 harboured 〈em〉bla〈/em〉〈sub〉OXA-48〈/sub〉 on similar mobile genetic elements to those identified in the clinical collection (pOXA-48 fragment in Ec_BM707 and IncL(pOXA-48) plasmid in Kp_BM758). Genetic similarities were observed between Ec_BM707 and several of the clinical ST131 〈em〉E. coli,〈/em〉 with allele matches at up to 98.2% of 2513 core genome multilocus sequence type (cgMLST) loci. In contrast, Kp_BM758 and the 34 clinical 〈em〉K. pneumoniae〈/em〉 were genetically distant. The source of the CPE at this site was not identified. The detection of OXA-48-like-producing ST131 〈em〉E. coli〈/em〉 and OXA-48-like-producing ST101 〈em〉K. pneumoniae〈/em〉 in Irish recreational water is a concern. The potential for contamination of the aquatic environment to contribute to dissemination of CPE in Europe warrants further study.〈/p〉〈/div〉 〈/div〉 〈div xml:lang="en"〉 〈h5〉Graphical abstract〈/h5〉 〈div〉〈p〉〈figure〉〈img src="https://ars.els-cdn.com/content/image/1-s2.0-S0048969719330542-ga1.jpg" width="500" alt="Unlabelled Image" title="Unlabelled Image"〉〈/figure〉〈/p〉〈/div〉 〈/div〉

Description: 〈p〉Publication date: 10 November 2019〈/p〉 〈p〉〈b〉Source:〈/b〉 Science of The Total Environment, Volume 690〈/p〉 〈p〉Author(s): Zhenyi Chen, Robyn Schofield, Peter Rayner, Tianshu Zhang, Cheng Liu, Claire Vincent, Sonya Fiddes, Robert George Ryan, Joel Alroe, Zoran D. Ristovski, Ruhi S. Humphries, Melita D. Keywood, Jason Ward, Clare Paton-Walsh, Travis Naylor, Xiaowen Shu〈/p〉 〈div xml:lang="en"〉 〈h5〉Abstract〈/h5〉 〈div〉〈p〉The rapid environmental changes in Australia prompt a more thorough investigation of the influence of transportation, local emissions, and optical–chemical properties on aerosol production across the region. A month-long intensive measurement campaign was conducted during spring 2016 at Mission Beach, a remote coastal site west of the Great Barrier Reef (GBR) on the north-east coast of Australia. One aerosol pollution episode was investigated in early October. This event was governed by meteorological conditions and characterized by the increase in black carbon (BC) mass concentration (averaged value of 0.35 ± 0.20 μg m〈sup〉−3〈/sup〉). Under the influence of the continental transportation, a new layer of nucleation-mode aerosols with an initial size diameter of 20 nm was observed and aerosol number concentrations reached the peak of 6733 cm〈sup〉−3〈/sup〉 at a diameter of 29 nm. The averaged aerosol extinction coefficient at the height of 2 km was 150 Mm〈sup〉−1〈/sup〉, with a small depolarized ratio (3.5–5%). Simultaneously, the boundary layer height presented a fall–rise trend in the presence of these enhanced aerosol concentrations and became stable in a later stage of the episode. We did not observe clear boundary layer height diurnal variations from the LiDAR observations or from the Weather Research and Forecasting (WRF) model outputs, except in an earlier stage of the aerosol episode for the former. Although the sea breeze may have been responsible for these particles, on the balance of available data, we suggest that the aerosol properties at the GBR surface during this period are more likely influenced by regional transportation of continental sources, including biomass-burning aerosols.〈/p〉〈/div〉 〈/div〉 〈div xml:lang="en"〉 〈h5〉Graphical abstract〈/h5〉 〈div〉〈p〉〈figure〉〈img src="https://ars.els-cdn.com/content/image/1-s2.0-S0048969719331201-ga1.jpg" width="326" alt="Unlabelled Image" title="Unlabelled Image"〉〈/figure〉〈/p〉〈/div〉 〈/div〉

Description: 〈p〉Publication date: 10 November 2019〈/p〉 〈p〉〈b〉Source:〈/b〉 Science of The Total Environment, Volume 690〈/p〉 〈p〉Author(s): Pau Batlle-Vilanova, Laura Rovira-Alsina, Sebastià Puig, M. Dolors Balaguer, Pilar Icaran, Victor M. Monsalvo, Frank Rogalla, Jesús Colprim〈/p〉 〈div xml:lang="en"〉 〈h5〉Abstract〈/h5〉 〈div〉〈p〉Biogas production in wastewater treatment plants (WWTPs) plays a decisive role in the reduction of CO〈sub〉2〈/sub〉 emissions and energy needs in the context of the water-energy nexus. The biogas obtained from sewage sludge digestion can be converted into biomethane by the use of biogas upgrading technologies. In this regard, an innovative water scrubbing based technology, known as ABAD Bioenergy® is presented and considered in this work. The effluents resulting from this system consist of biomethane and treated wastewater with a high CO〈sub〉2〈/sub〉 concentration. Therefore, the study explores the feasibility of using this CO〈sub〉2〈/sub〉-containing effluent in the cathode of a bioelectrochemical system (BES) for the transformation of CO〈sub〉2〈/sub〉 into methane. Techno-economic assessment of the process is presented, including the valorisation of anode reactions through the production of chlorine compounds. Finally, the potential impacts of applying this technology in a WWTP operated by FCC Aqualia are (i) increasing biomethane production by 17.4%, (ii) decreasing CO〈sub〉2〈/sub〉 content by 42.8% and (iii) producing over 60 ppm of chlorine compounds to disinfect all the treated wastewater of the plant.〈/p〉〈/div〉 〈/div〉 〈div xml:lang="en"〉 〈h5〉Graphical abstract〈/h5〉 〈div〉〈p〉〈figure〉〈img src="https://ars.els-cdn.com/content/image/1-s2.0-S0048969719329341-ga1.jpg" width="265" alt="Unlabelled Image" title="Unlabelled Image"〉〈/figure〉〈/p〉〈/div〉 〈/div〉

Description: 〈p〉Publication date: 1 September 2019〈/p〉 〈p〉〈b〉Source:〈/b〉 Journal of Chromatography B, Volume 1125〈/p〉 〈p〉Author(s): Roberta Natália Cestari, Adriana Rocha, Renê Donizeti Ribeiro de Oliveira, Vera Lucia Lanchote〈/p〉 〈div xml:lang="en"〉 〈h5〉Abstract〈/h5〉 〈div〉〈p〉Gemfibrozil (GFZ) is a derivative of fibric acid and is used in the treatment of dyslipidemia. GFZ may affect the metabolism of various drugs, including statins, by inhibiting the sinusoidal influx transporter OATP1B1 and also CYP2C9 and CYP2C8 enzymes. This study presents the development and validation of a rapid, simple, sensitive and reproducible method of GFZ analysis in human plasma using UPLC-MS/MS. The method was applied in a pharmacokinetic study following administration of multiple doses of 600 mg GFZ every 12 h in healthy volunteers (〈em〉n〈/em〉 = 15). GFZ was separated on a C18 column using a mixture of 0.01% formic acid and acetonitrile (40:60, v/v) as the mobile phase at a flow rate of 0.4 mL/min. The method showed linearity in the range from 0.01 μg/mL to 100 μg/mL plasma. The coefficients of variation and the relative standard errors of the accuracy and precision analyses were 〈15%. The method allowed quantification of plasma concentrations of GFZ in the dose interval of the sixth day of administration of multiple oral doses of GFZ every 12 h. The pharmacokinetic parameters are presented as mean (95% CI): area under the plasma concentration 〈em〉versus〈/em〉 time curve 〈strong〉88.84〈/strong〉 (72.72–104.96) μg·h/mL, steady state mean plasma concentration 7.40 (6.06–8.75) μg/mL, minimum plasma concentration 1.24 (0.87–1.61) μg/mL, maximum plasma concentration 26.73 (21.31–32.15) μg/mL, time to reach maximum plasma concentration 2.28 (1.42–3.13) h, elimination half-life 2.81 (2.22–3.40) h, apparent total clearance 7.72 (5.85–9.58) L/h, apparent distribution volume 33.97 (18.41–49.53) L. In conclusion, the method for analysis of GFZ in human plasma showed sensitivity, linearity, precision and accuracy compatible with application in pharmacokinetic studies of multiple oral dose of 600 mg GFZ every 12 h.〈/p〉〈/div〉 〈/div〉

Description: 〈p〉Publication date: 10 November 2019〈/p〉 〈p〉〈b〉Source:〈/b〉 Science of The Total Environment, Volume 690〈/p〉 〈p〉Author(s): Muhammad Bilal, Hafiz M.N. Iqbal〈/p〉 〈div xml:lang="en"〉 〈h5〉Abstract〈/h5〉 〈div〉〈p〉Steroidal estrogens are widespread water contaminants with potential carcinogenic and endocrine-disrupting activities. The World Health Organization has listed estrogens as group 1 carcinogens. These contaminants are of substantial concern because of potential threats to human health, and aquatic organisms on long-term exposure. A range of methods, including oxidation, adsorption, electrochemical, and irradiation techniques have been employed for their remediation from aqueous systems. However, inadequate removal, toxic sludge generation, high operating costs, and the requisite for skilled operating and maintenance personnel commercially hampered the application of many methods. An interesting alternative treatment approach based on the use of oxidoreductases, particularly laccases, has recently gained amicability for the biotransformation of emerging pollutants. The use of immobilized enzymes is more cost-effective from an industrial perspective due to improved catalytic stability, reusability, reduction of product inhibition, and easier product separation. This review provides comprehensive knowledge on the use of laccases in the biodegradation of steroidal estrogens, including estrone, 17〈em〉β〈/em〉-estradiol, and 17〈em〉α〈/em〉-ethinylestradiol with endocrine-disrupting potency from the environment. After an overview of estrogens and catalytic properties of laccase, the use of free, as well as immobilized laccases with a particular emphasis on estrogens removal by laccase-based fed-batch, packed bed bioreactors, and membrane reactors, is discussed. A comparison of existing treatment technologies with enzyme technology for the removal of estrogens from different environmental matrices is made. Lastly, along with concluding remarks, future research direction aimed at bridging knowledge gaps for estrogenic compounds removal are also proposed in this very important research area.〈/p〉〈/div〉 〈/div〉 〈div xml:lang="en"〉 〈h5〉Graphical abstract〈/h5〉 〈div〉〈p〉〈figure〉〈img src="https://ars.els-cdn.com/content/image/1-s2.0-S0048969719331389-ga1.jpg" width="227" alt="Unlabelled Image" title="Unlabelled Image"〉〈/figure〉〈/p〉〈/div〉 〈/div〉

Description: 〈p〉Publication date: Available online 8 July 2019〈/p〉 〈p〉〈b〉Source:〈/b〉 Journal of Chromatography A〈/p〉 〈p〉Author(s): Jonas Henschel, Simon Wiemers-Meyer, Marcel Diehl, Constantin Lürenbaum, Wen Jiang, Martin Winter, Sascha Nowak〈/p〉 〈h5〉Abstract〈/h5〉 〈div〉〈p〉The expansion of lithium ion battery (LIB) application is accompanied by the growth of battery pack sizes. This progression emphasizes the consideration of electrolyte safety as well as environmental aspects in case of abuse, accident, or recycling. Hexafluorophosphate is one of the most commonly used conducting salt anions in electrolytes. It has great potential to degrade to various acidic and non-acidic organo(fluoro)phosphates with presence of water and during battery cell operation. Consequently, toxicological investigation on these organo(fluoro)phosphates has emerged because they either have structural similarities as chemical warfare agents or play a widespread physiological role as phosphates in the human body. This circumstance underlines the need of isolated examination of these compounds for safety assessment. In this work, we used hydrophilic interaction liquid chromatography for the extraction of acidic organofluorophosphates from thermally aged LIB electrolytes. The developed two-step fractionation method provided high separation selectivity towards acidic head groups, which allowed the separation of undesired matrix and target compounds. These findings facilitate isolated toxicological investigations on organofluorophosphates that are beneficial for environmental and safety research, the battery cell industry, and human safety surveillance in regard to aged LIB electrolytes.〈/p〉〈/div〉

Description: 〈p〉Publication date: September 2019〈/p〉 〈p〉〈b〉Source:〈/b〉 Biological Conservation, Volume 237〈/p〉 〈p〉Author(s): Joshua I. Brian, David C. Aldridge〈/p〉 〈div xml:lang="en"〉 〈h5〉Abstract〈/h5〉 〈div〉〈p〉Endosymbionts can often have profound impacts on the growth, reproduction and survivorship of their hosts. Freshwater unionid mussels (Unionida) are important ecosystem engineers, and one of the most globally imperilled taxa, yet evidence concerning their endosymbiotic fauna remains patchy. Further, endosymbionts are not considered in an IUCN assessment for any unionid mussel. Here, we conduct the first literature review of all endosymbionts of the 16 extant European and 279 extant North American unionids, in addition to the four most significant invasive bivalves in Europe. There were 1476 host-endosymbiont records from 239 different studies over a 168-year period, documenting at least 188 unique endosymbiont taxa. However, study effort was uneven in its distribution, with 53% of unionid species (n = 157) having no endosymbiont records. Eighty-eight percent of all hosts are considered under-sampled, including 99% of Endangered or Critically Endangered mussels. This is of significant concern given that when the effects of endosymbionts were examined, 72% showed potentially negative effects on their host, including complete castration in the case of digenean trematodes. However, only a small number of endosymbionts have had their effects quantified. Bipartite network analyses revealed invasive mussels may be competent for native parasites. This leads to the potential for parasite spillback, with conservation implications for vulnerable native species. Recommendations for future work include greater sampling of sympatric native and invasive populations (including non-destructive sampling of endangered species) and experimental manipulation of host-endosymbiont communities. This will facilitate better conservation outcomes for this crucial group of ecosystem engineers.〈/p〉〈/div〉 〈/div〉 〈div xml:lang="en"〉 〈h5〉Graphical abstract〈/h5〉 〈div〉〈p〉〈figure〉〈img src="https://ars.els-cdn.com/content/image/1-s2.0-S0006320719306706-ga1.jpg" width="204" alt="Unlabelled Image" title="Unlabelled Image"〉〈/figure〉〈/p〉〈/div〉 〈/div〉

Description: 〈p〉Publication date: 1 November 2019〈/p〉 〈p〉〈b〉Source:〈/b〉 Agriculture, Ecosystems & Environment, Volume 283〈/p〉 〈p〉Author(s): 〈/p〉

Description: 〈p〉Publication date: 1 November 2019〈/p〉 〈p〉〈b〉Source:〈/b〉 Solid State Ionics, Volume 340〈/p〉 〈p〉Author(s): Shyamal K. Das, Thangavelu Palaniselvam, Philipp Adelhelm〈/p〉 〈div xml:lang="en"〉 〈h5〉Abstract〈/h5〉 〈div〉〈p〉The renewal of research interest in rechargeable aluminum-ion batteries could be seen as a massive boost for the exploration of Al〈sup〉3+〈/sup〉-ion electroactive electrode materials in recent times. Titanium dioxide (TiO〈sub〉2〈/sub〉) is less explored but could be a promising electrode material for aluminum-ion battery. Here, we demonstrate the rechargeability of an Al-ion cell with anatase TiO〈sub〉2〈/sub〉 as cathode in chloroaluminate ionic liquid electrolyte. The Al-TiO〈sub〉2〈/sub〉 cell exhibited excellent long-term stability with maximum specific capacity of 25 mAh g〈sup〉−〈/sup〉〈sup〉1〈/sup〉 at current rate of 500 mA g〈sup〉−〈/sup〉〈sup〉1〈/sup〉 at room temperature. The electroactive nature of TiO〈sub〉2〈/sub〉 in the chloroaluminate electrolyte is clearly demonstrated both by cyclic voltammetry and galvanostatic cycling studies. The synergistic effect of current collector in improving the long-term stability of Al-TiO〈sub〉2〈/sub〉 cell is also revealed.〈/p〉〈/div〉 〈/div〉

Description: 〈p〉Publication date: September 2019〈/p〉 〈p〉〈b〉Source:〈/b〉 Biological Conservation, Volume 237〈/p〉 〈p〉Author(s): Julia E. Earl〈/p〉 〈div xml:lang="en"〉 〈h5〉Abstract〈/h5〉 〈div〉〈p〉Population projection models, such as matrix and integral projection models, are used increasingly to understand potential effects of anthropogenic stressors and inform conservation actions. However, vital rate and life history information needed to create robust population models is often missing or incomplete, making assumptions about parameters and population processes necessary. Understanding how assumptions affect results is critical, particularly if the study will be used to guide policy or management actions. I review published amphibian population projection models to determine whether model output is evaluated with population data, what assumptions are made, and whether sensitivity analyses are performed. I found that only 21% of published models were evaluated with population data, and most models (67%) were explored with sensitivity analyses. I then simulated the effects of four assumptions and varying population carrying capacities on model output and sensitivity results using existing matrix population models from three amphibian species with different life histories: 〈em〉Anaxyrus boreas, Lithobates sylvaticus,〈/em〉 and 〈em〉Ambystoma maculatum〈/em〉. Simulations showed that changes in model output and sensitivity analyses under different assumptions depended more on the species examined than the assumption implemented. There were changes in which parameters model output was most sensitive to under all assumptions examined for all species, suggesting caution when using results if there is great uncertainty about model assumptions. Models and their parameterization should be regularly updated with new information to ensure conservation biologists are using the most robust information on potential outcomes of threats and conservation actions.〈/p〉〈/div〉 〈/div〉

Description: 〈p〉Publication date: Available online 8 July 2019〈/p〉 〈p〉〈b〉Source:〈/b〉 Biological Conservation〈/p〉 〈p〉Author(s): Davi Castro Tavares, Jailson Fulgencio Moura, Agostino Merico〈/p〉 〈div xml:lang="en"〉 〈h5〉Abstract〈/h5〉 〈div〉〈p〉Anthropogenic debris is rapidly spreading in marine environments and poses major problems to biodiversity and humans. However, mitigation strategies are limited by the lack of information on the accumulation patterns of these pollutants both at sea and in marine wildlife. Using observations from an uninhabited island in Delta du Saloum National Park, Senegal, we investigate here the prevalence and abundance of debris in nests of two sympatric seabird species, Caspian terns 〈em〉Hydroprogne caspia〈/em〉 and great cormorants 〈em〉Phalacrocorax carbo〈/em〉, and its potential as an indicator of ocean pollution. We recorded debris in 15% of the Caspian terns' nests, and 40% of the great cormorants' nests. Plastics accounted for 〉 95% of items recorded in the nests of both species. Caspian terns collected a diverse array of debris, both in terms of types and colours, with a preference for hard plastics and white items. The great cormorants accumulated in nests mainly greenish fishing gears resembling the vegetation typically used as nest materials. Nests of both bird species contained soft plastic in proportions lower than those observed in the environment. Our results suggest that nests of Caspian terns and great cormorants are not useful indicators of pollution by anthropogenic debris in the surrounding waters of the Delta du Saloum National Park. Nests of great cormorants, however, have the potential to indicate areas vulnerable to plastic pollution associated to fishery. The high amount of debris in nests of this species demonstrates the need for a better implementation of waste management strategies in Senegal.〈/p〉〈/div〉 〈/div〉

Description: 〈p〉Publication date: October 2019〈/p〉 〈p〉〈b〉Source:〈/b〉 Journal of Petroleum Science and Engineering, Volume 181〈/p〉 〈p〉Author(s): Shuai Zhao, Wanfen Pu, Mikhail A. Varfolomeev, Chengdong Yuan, Shan Qin, Liangliang Wang, Dmitrii A. Emelianov, Artashes A. Khachatrian〈/p〉 〈div xml:lang="en"〉 〈h5〉Abstract〈/h5〉 〈div〉〈p〉Because the thermal release correlates directly with the success of in-situ combustion (ISC) technology, this research performs a series of investigations concerning thermal behavior and kinetics of heavy crude oil during combustion using high pressure differential scanning calorimetry (HP-DSC) and accelerating rate calorimetry (ARC). The results obtained from HP-DSC profiles indicated that for oil alone and its mixtures with quartz sand/crushed core, the peak temperature was lowered, and the heat flow increased with increasing oxygen partial pressure. The heat enthalpy of low temperature oxidation (LTO) was higher than that of high temperature oxidation (HTO) under oxygen partial pressures of 0.5, 1 and 1.5 MPa, and the increase in heat enthalpy of LTO with oxygen partial pressure was more pronounced than that of HTO. Unlike the crushed core, the addition of quartz sand delayed exothermic oxidation reactions. Compared with oil only and oil + quartz sand, the LTO and HTO peak temperatures of oil + crushed core were considerably lowered, and the effect of crushed core on increasing heat release for LTO at oxygen partial pressure of 1.5 MPa was more prominent. It was observed that the heat enthalpy of LTO and HTO increased quasi-linearly with the oxygen partial pressure in both the presence and absence of quartz sand/crushed core. ISC might be considered as an appropriate candidate for Jiqi block, based on exothermic continuity of the ARC curves, with the near-wellbore zone of target block heated to 180 °C where the exothermic oxidation activity is notably intensified. The kinetic results showed that the LTO and HTO intervals were divided into 6 and 2 subintervals, respectively, which facilitated more precise modelling of the ISC process.〈/p〉〈/div〉 〈/div〉

Description: 〈p〉Publication date: October 2019〈/p〉 〈p〉〈b〉Source:〈/b〉 Journal of Petroleum Science and Engineering, Volume 181〈/p〉 〈p〉Author(s): Zan Chen, Menglu Lin, Shuhua Wang, Shengnan Chen, Linsong Cheng〈/p〉 〈div xml:lang="en"〉 〈h5〉Abstract〈/h5〉 〈div〉〈p〉Studies have shown that the gas huff and puff injection potentially perform better than the continuous gas flooding in enhancing the hydrocarbon recovery in the liquid rich tight reservoirs. During the fracturing stimulation, only part of the induced hydraulic fractures is propped because proppants cannot be carried to the fracture tips. Moreover, some secondary and tertiary fractures may be too narrow to accommodate any proppants. The conductivity of the unpropped fractures is highly dependent on the variation of the in-situ pressure and may be open and close periodically during the huff-n-puff cycles. In this study, the stress-dependent fracture conductivity and its impact on the produced gas huff-n-puff performance are investigated in a liquid rich tight reservoir, considering the existence of the large amount of the unpropped fractures. The experimental data of stress-dependent fracture conductivity is employed first to simulate the dynamic conductivity during the depletion and the gas huff and puff cycles. A reservoir model is then constructed and history-matched based on the reservoir fluid samples and the field production data collected from the Montney liquid rich tight reservoir in Western Canada. Performance of the produced gas huff-n-puff is examined in the targeted reservoir and results show that contributions of the unpropped fractures cannot be ignored, which leads to 7.8% more condensate (i.e., oil) production and 2.8% higher in barrel of oil equivalent (BOE), compared to the case with propped fractures only. The effects of complex fracture geometry and the cluster completion are also investigated and results show that the unpropped fracture contributions towards the condensate production and BOE are even more pronounced in the complicated scenarios. The condensate oil and BOE are 42.0% and 22.9% higher in complex fracture geometry case and 12.4% and 5.6% higher in the fractures with multiple clusters than those scenarios with propped fractures only. This paper provides a better understanding on the potential performance of enhanced hydrocarbons recovery in liquid rich tight gas reservoirs via gas huff-n-puff operations.〈/p〉〈/div〉 〈/div〉

Description: 〈p〉Publication date: October 2019〈/p〉 〈p〉〈b〉Source:〈/b〉 Journal of Petroleum Science and Engineering, Volume 181〈/p〉 〈p〉Author(s): Abdelrahman Elkhateeb, Reza Rezaee, Ali Kadkhodaie〈/p〉 〈div xml:lang="en"〉 〈h5〉Abstract〈/h5〉 〈div〉 〈p〉Traditionally, prediction of facies and permeability for a reservoir rock was one of many challenges in the industry that necessitates advanced and sophisticated evaluation for effective reservoir description. Three wells have been studied in the Perth Basin in Western Australia across the shaly sand of the Irwin River Coal Measures Formation, which contain a comprehensive suite of advanced and conventional logs. Due to the reservoir heterogeneity and the clay distribution, it is very challenging to resolve the effective pore volume, the reservoir facies and how the high permeability zones are distributed within the formation.〈/p〉 〈p〉In this paper, a new technique has been successfully tested on the Shaly Sand by integrating the nuclear magnetic resonance (NMR) and the conventional density log. The method allows the establishment of high-resolution facies classification for the reservoir using an Equivalent Flow Zone Indicator Index (EFZI). The studied core facies have been integrated with the EFZI into a new workflow to distribute facies on a larger scale in the uncored wells.〈/p〉 〈p〉Four hydraulic flow units (HFU) have been defined from one cored well using Flow Zone Indicator approach, with each has a unique FZI value and different permeability model based on core measurements. The EFZI-based high-resolution facies have been validated at several formation depths using the core thin sections to ensure the best calibration will be obtained for facies log, hence the permeability log-to-core match.〈/p〉 〈p〉The methodology will help running an advanced petrophysical analysis for the zone of interest and will reduce the parameters uncertainty. Application of this methodology in the uncored wells has shown very encouraging results, which is believed it can be used in the absence of any core data to resolve the rock typing from the well logs.〈/p〉 〈/div〉 〈/div〉

Description: 〈p〉Publication date: October 2019〈/p〉 〈p〉〈b〉Source:〈/b〉 Journal of Petroleum Science and Engineering, Volume 181〈/p〉 〈p〉Author(s): Atousa Heydari, Kiana Peyvandi〈/p〉 〈div xml:lang="en"〉 〈h5〉Abstract〈/h5〉 〈div〉〈p〉In this work, the stainless steel mesh was used to study the effect of metallic porous media on the formation of methane hydrate and some parameters such as induction time, the kinetics growth and the mole of gas consumed have been investigated at a temperature of 3 °C (276.15 K) and a pressure of 760 psi (5.24Mpa). The metallic porous media was able to show better results on the methane hydrate formation relative to the silica gel. Hence the induction time and, eventually, the total time of the hydrate formation process decreased by about 60%. The kinetics growth and the amount of gas consumed increased significantly. Also, the effect of two types of anionic and nonionic surfactants as kinetics promoters studied in this porous media. The result of adding SDS and SDBS at a concentration near the CMC designated that the induction time lasted nearly zero and the total time of the process by SDBS was minimal. It should be noted that the non-ionic surfactant SPAN 80 could not have a positive effect on this porous media. In general, therefore, the results of this research attempts to show that the stainless steel mesh with SDBS possessed high potential in obtaining the industrial purpose of gas hydrate growth and also was significant in the field of energy storage and transport.〈/p〉〈/div〉 〈/div〉 〈h5〉Graphical abstract〈/h5〉 〈div〉〈p〉〈figure〉〈img src="https://ars.els-cdn.com/content/image/1-s2.0-S0920410519306473-fx1.jpg" width="500" alt="Image 1" title="Image 1"〉〈/figure〉〈/p〉〈/div〉

Description: 〈p〉Publication date: October 2019〈/p〉 〈p〉〈b〉Source:〈/b〉 Ecological Engineering, Volume 136〈/p〉 〈p〉Author(s): Ramón Perea, Jessica S. Cunha, Cristiani Spadeto, Vanessa M. Gomes, Arthur L. Moura, Bárbara Rúbia, G. Wilson Fernandes〈/p〉 〈div xml:lang="en"〉 〈h5〉Abstract〈/h5〉 〈div〉〈p〉Roads are known to be a major factor in the ongoing spread and establishment of invasive plants by modifying habitats and providing movement corridors. Controlling plant invasion or restoring highly-invaded areas along roads is a challenging task in current conservation practice. We aim to investigate the possible facilitative effects of nurse shrubs on native vs. exotic species in order to provide applications for conservation and restoration of highly invaded roadsides areas in megadiverse montane areas of Brazil. We estimated the abundance of each plant species (native and exotic) in paired roadsides with and without pioneer nurse shrubs (〈em〉Baccharis〈/em〉 spp.), and measured whether they were facilitated (i.e., growing underneath native nurse shrubs), using a Facilitation Value metric. We found that the proportion of exotic species was 27% greater in areas without the nurse shrubs. In addition, predicted probability of nurse shrubs as facilitators of native species was 61% greater than that of exotic species. Pioneer nurse shrubs that alleviate the environmental shift generated by the construction and use of roads (e.g., disturbed soils with low nutrient content) may represent an interesting alternative to mitigate exotic plant invasion along roadsides, a current global priority for biodiversity conservation. Decision-makers considering whether to build, improve, and maintain roads should take into account the potential spread of exotic plants and the use of nurse shrubs to prevent or mitigate plant invasiveness.〈/p〉〈/div〉 〈/div〉 〈div xml:lang="en"〉 〈h5〉Graphical abstract〈/h5〉 〈div〉〈p〉〈figure〉〈img src="https://ars.els-cdn.com/content/image/1-s2.0-S0925857419302216-ga1.jpg" width="263" alt="Graphical abstract for this article" title=""〉〈/figure〉〈/p〉〈/div〉 〈/div〉

Description: 〈p〉Publication date: October 2019〈/p〉 〈p〉〈b〉Source:〈/b〉 Journal of Petroleum Science and Engineering, Volume 181〈/p〉 〈p〉Author(s): Shuaishuai Jiang, Xuehua Chen, Yingkai Qi, Wei Jiang, Jie Zhang, Zhenhua He〈/p〉 〈div xml:lang="en"〉 〈h5〉Abstract〈/h5〉 〈div〉〈p〉The frequency-dependent attenuation and velocity dispersion of seismic responses are closely related to hydrocarbon reservoirs. To further investigate the characteristics of seismic responses caused by pore fluid-bearing reservoirs, the role of gas saturation is analyzed in seismic responses of sand reservoirs characterized by the patchy saturation model. To this end, a novel wave extrapolation method is developed based on the diffusive-viscous wave equation (DVWE) as well as a scheme for an extended local Rytov Fourier (ELRF) approximation within the extrapolation depth interval. Our proposed method considers the presence of fluid mixtures in the porous media, resulting in seismic attenuation and dispersion by the mechanism generally known as wave-induced fluid flow (WIFF). This method enables an accommodation for the lateral variations in slowness, diffusion coefficient and viscosity. Subsequently, the extrapolation is adopted to model the synthetic seismic data of a distributary channel model. During this modeling, a gas-water saturated sand reservoir embedded into one of the channels was used to comparatively analyze the distinct features on its seismic synthetic data. We exhibited the numerical simulation results using the proposed wave extrapolation method here and the traditional acoustic wave equation (AWE) method. A comparison of the simulation results, demonstrates that our proposed numerical method can depict the seismic dispersion and frequency-dependent attenuation as well as the phase delay effects associated with gas-water-saturated sand reservoirs. Furthermore, we compare the seismic responses by changing the gas saturations of the sand reservoir. The gas saturation of the reservoir has significant effects on the seismic characteristics of the numerical modeling data. The numerical modeling method improves our understanding of the mechanisms of seismic frequency-dependent characteristics associated with gas saturations and potentially contributes to better insights into gas reservoir indicators derived from seismic field data.〈/p〉〈/div〉 〈/div〉

Description: 〈p〉Publication date: 15 August 2019〈/p〉 〈p〉〈b〉Source:〈/b〉 Tetrahedron Letters, Volume 60, Issue 33〈/p〉 〈p〉Author(s): Mitali Mishra, Seetaram Mohapatra, Nilima Priyadarsini Mishra, Bighnanshu K. Jena, Pravati Panda, Sabita Nayak〈/p〉 〈div xml:lang="en"〉 〈h5〉Abstract〈/h5〉 〈div〉〈p〉Heterocyclic compounds particularly five, six and seven membered ring containing heterocycles are the most abundant which constitute a staggeringly diverse and important class of molecules that occur ubiquitously in a variety of synthetic drugs, bioactive natural products, pharmaceuticals and agrochemicals. Owing to the glorious past and impressive present of the biologically active heterocyclic scaffolds, these skeletons have long been a subject of immense interest. Hence, substantial efforts have been made to the development of new and innovative synthetic strategies for the synthesis of these heterocycles involving use of different metal catalysts, organic and inorganic reagents etc. Among the different types of metal catalysts used, iron catalysts are one of the cheap and easily available. In recent time, several new and innovative iron(III) chloride catalyzed synthesis of heterocycles with structural diversity are coming in the forefront of the literature by the scientific community. This review highlights the advancements made so far by iron(III) chloride for the synthesis of different assemblies of small heterocycles covering the year 2014–2018.〈/p〉〈/div〉 〈/div〉 〈div xml:lang="en"〉 〈h5〉Graphical abstract〈/h5〉 〈div〉〈p〉〈figure〉〈img src="https://ars.els-cdn.com/content/image/1-s2.0-S0040403919306628-ga1.jpg" width="261" alt="Graphical abstract for this article" title=""〉〈/figure〉〈/p〉〈/div〉 〈/div〉

Description: 〈p〉Publication date: August 2019〈/p〉 〈p〉〈b〉Source:〈/b〉 Ocean Modelling, Volume 140〈/p〉 〈p〉Author(s): Oleg Druzhinin, Yuliya Troitskaya, Wu-ting Tsai, Po-chen Chen〈/p〉 〈div xml:lang="en"〉 〈h5〉Abstract〈/h5〉 〈div〉〈p〉The present study is concerned with direct numerical simulation (DNS) of turbulent air flow over a waved water surface. Three-dimensional, turbulent Couette flow is considered in DNS as a model of a constant-flux layer in the marine atmospheric surface layer. Two-dimensional stationary waves at the water surface are prescribed and assumed to be unaffected by the air-flow. We consider capillary-gravity water surface waves and are interested in the influence of “parasitic” capillary ripples riding on the carrier, energy-containing waves, on the properties of the air-flow. The surface waves are prescribed and considered to be stationary, the capillaries being in phase with the carrier wave. The surface elevations spectra are also prescribed and mimicking stationary capillaries riding on Stokes waves observed in a 2D numerical simulation of water-surface capillary-gravity waves by Hung & Tsai (2009). The bulk air velocity and the carrier water surface waves lengths are considered in our DNS in the range of 3 to 5 m/s and 3 to 7 cm, respectively. Under these conditions, the capillaries are found to be submerged within the viscous sublayer of the atmospheric boundary layer. Our DNS results show that although the flow fields are characterized by instantaneous separations of the boundary layer, the ensemble (wave-phase) averaged flow fields are non-separating and well predicted by a quasilinear theoretical model. We find also that capillaries mitigate the development of coherent (horse-shoe) vortex structures as compared to the no-ripples flow-case. We further use DNS results and quasilinear model formulation to parameterize the water surface roughness height in terms of critical layer thickness and the amplitude of a dominant, energy-containing harmonic of the water surface elevation spectrum.〈/p〉〈/div〉 〈/div〉

Description: 〈p〉Publication date: July–August 2019〈/p〉 〈p〉〈b〉Source:〈/b〉 Materials Today, Volume 27〈/p〉 〈p〉Author(s): George F. Vander Voort〈/p〉

Description: 〈p〉Publication date: 5 October 2019〈/p〉 〈p〉〈b〉Source:〈/b〉 Journal of Alloys and Compounds, Volume 804〈/p〉 〈p〉Author(s): Hiral D. Shah, J.A. Bhalodia〈/p〉 〈div xml:lang="en"〉 〈h5〉Abstract〈/h5〉 〈div〉〈p〉In this communication, we report the structural and electrical transport properties of (1-〈em〉x〈/em〉) La〈sub〉0.7〈/sub〉Sr〈sub〉0.3〈/sub〉Mn〈sub〉0.95〈/sub〉Co〈sub〉0.05〈/sub〉O〈sub〉3〈/sub〉 (LSMCO) + (〈em〉x〈/em〉) ZnO (〈em〉x〈/em〉 = 0%, 6%, 9%, 12%, 15% & 18%) composites. For the preparation of (1-〈em〉x〈/em〉) LSMCO + (〈em〉x〈/em〉) ZnO (〈em〉x〈/em〉 = 6%, 9%, 12%, 15% & 18%) composites, sample of LSMCO was prepared by the auto combustion technique/inexpensive modified sol-gel technique. The results of Rietveld refined XRD data show that LSMCO sample possesses a rhombohedral structure with the 〈em〉R-3c〈/em〉 space group whereas ZnO compound remains with hexagonal structure with the 〈em〉P6〈/em〉〈sub〉〈em〉3〈/em〉〈/sub〉〈em〉mc〈/em〉 space group in all the composite samples. The X-ray diffraction (XRD) and scanning electron microscopy (SEM) show that no any extra unwanted phase was observed in each composite excluding the LSMCO and ZnO phases. ZnO is mostly distributed at the grain boundaries and on the surface of the LSMCO grains. Elemental presence and ratio was confirmed through the EDX analysis. The electrical resistivity of LSMCO and each composite was measured in the temperature range of 2 K–320 K at 0 Oe, 10 kOe, 50 kOe & 90 kOe magnetic field. The results indicate that the ZnO addition increases the resistivity of all the composites compare to that of pure LSMCO. The electrical resistivity explored by the theoretical model below 〈em〉T〈/em〉〈sub〉MI〈/sub〉 and fitting enlightenment for the observed behavior is transmitted here in detail.〈/p〉〈/div〉 〈/div〉

Description: 〈p〉Publication date: 5 October 2019〈/p〉 〈p〉〈b〉Source:〈/b〉 Journal of Alloys and Compounds, Volume 804〈/p〉 〈p〉Author(s): Dezhi Yang, Weihua Liu, Dingfu Cheng, Jieshi Chen, Hao Lu, Chun Yu, Jijin Xu〈/p〉 〈div xml:lang="en"〉 〈h5〉Abstract〈/h5〉 〈div〉〈p〉(Co, Cr)23C6 type carbide is a typical metallic compound in many cobalt bearing alloys, and it acts as the strengthening phase in the form of bulk eutectic carbides or precipitated carbides. In this work, first-principles calculations were carried out to investigate the electronic structure, phase stability, mechanical and magnetic properties of (Co, Cr)23C6 with different cobalt occupation. Some of the calculated values are compared with previous studies and, they are found to be in a good agreement. The method considering curvature radius is firstly used to describe the degree of anisotropy. The hardness calculated through elastic constants presents an approximate downtrend with the cobalt concentration. Analysis of the density of states (DOS), overlapped population and electron density maps, indicates that the bonds in (Co, Cr)23C6 are the mixture of covalent, ionic and metallic bonds, the interactions of 〈em〉d-d〈/em〉 orbits between metallic atoms contribute most to the hybridization mode. According to the population analysis, the reduction in hardness can attribute to the increase of metallicity and iconicity of the interacted metallic atoms. In addition, the formation of a large quantity of antibonding also plays a negative role in intrinsic hardness of (Co, Cr)23C6 when massive substitution of cobalt atom.〈/p〉〈/div〉 〈/div〉

Description: 〈p〉Publication date: 5 October 2019〈/p〉 〈p〉〈b〉Source:〈/b〉 Journal of Alloys and Compounds, Volume 804〈/p〉 〈p〉Author(s): Morteza Alizadeh, Andisheh Shakery, Erfan Salahinejad〈/p〉 〈div xml:lang="en"〉 〈h5〉Abstract〈/h5〉 〈div〉〈p〉In this research, the structure and mechanical properties of 1050 aluminum strips reinforced with E-glass fibers, processed by the cross accumulative roll bonding (CARB) process, were investigated from microscopic, hardness, tensile and peeling viewpoints. The results indicated that the incorporation of the glass fibers in the Al matrix increases strength and micro-hardness but decreases elongation. In addition, it was realized that some of these fibers are broken and changed to short fibers during the CARB process. The presence of the glass fibers strongly also reduces the bond efficiency of the Al strips, typically from 50% to 5%. To compensate this deleterious effect, it was found that at least 25% should be increased to the normal thickness reduction used in CRAB.〈/p〉〈/div〉 〈/div〉

Description: 〈p〉Publication date: September 2019〈/p〉 〈p〉〈b〉Source:〈/b〉 Journal of Microbiological Methods, Volume 164〈/p〉 〈p〉Author(s): Kamila Oliveira Santos, João Costa-Filho, Kérolin Luana Spagnol, Luis Fernando Marins〈/p〉 〈div xml:lang="en"〉 〈h5〉Abstract〈/h5〉 〈div〉〈p〉The present study evaluated the stability of 〈em〉Bacillus subtilis〈/em〉 strains transformed with a replicative or integrative plasmid (via CRISPR-Cas9) to express a recombinant phytase. Both transformation methods did not affect the growth of 〈em〉B. subtilis〈/em〉, but the stability of the construct and the enzymatic activity was reduced in the strain transformed with the replicative plasmid.〈/p〉〈/div〉 〈/div〉

Description: 〈p〉Publication date: Available online 9 July 2019〈/p〉 〈p〉〈b〉Source:〈/b〉 Acta Astronautica〈/p〉 〈p〉Author(s): Bing Xiong, Xiao-qiang Fan, Yi Wang〈/p〉 〈div xml:lang="en"〉 〈h5〉Abstract〈/h5〉 〈div〉〈p〉To improve the performance of a hypersonic inward turning inlet, an optimization design method was proposed. A parameterization methodology was developed for an axisymmetric basic flowfield, and the geometry of a basic flowfield can be easily generated in several parameters. Preliminarily, an optimization targeting on the basic flowfield performance was conducted. As a result, the total pressure recovery of the basic flowfield was improved 7.65% compared with the referred one under the same constraints. The corresponding stream-traced inlet performance was also improved 5.65%. For further optimization, an optimization directly targeting on the 3-D inlet performance was carried out. The method of calculating along streamlines (MCS), which is for the fast calculation of a stream-traced inlet flowfield, was proposed and confirmed before this optimization. The result shows that the 3-D inlet total pressure can be further enhanced 6.74% than the previous one, and it is 12.78% higher than the referred one. That is to say, it is more reasonable to target on the inlet performance directly for an optimization, rather than targeting on the basic flowfield performance. By statistically analyzing the optimization data, it was found that the opinion “A better basic flowfield means a better stream-traced inlet” is statistically correct, but not exactly correct. The steam-traced inlet performance is not exactly determined by a basic flowfield, and it is determined by a combination of all the flow tubes the inlet captures.〈/p〉〈/div〉 〈/div〉

Description: 〈p〉Publication date: October 2019〈/p〉 〈p〉〈b〉Source:〈/b〉 Soil Dynamics and Earthquake Engineering, Volume 125〈/p〉 〈p〉Author(s): Ahmet Hilmi Deringöl, Esra Mete Güneyisi〈/p〉 〈div xml:lang="en"〉 〈h5〉Abstract〈/h5〉 〈div〉〈p〉This study investigates the influence of the friction pendulum bearing (FPB) isolator characteristics on the nonlinear response of the buildings under various seismic excitations. To represent a wide range of assessment, 3, 6, and 9-storey steel framed buildings with twenty seven different isolation models of FPB were studied by identifying the local and global deformations. Three important parameters such as isolation period T (as 2, 2.5, and 3 s), effective damping ratio ß (as 0.05, 0.15, 0.25), and yield strength ratio Fy/W (as 0.025, 0.05, and 0.10) were used in the modelling of FPB. Two-dimensional model of the base-isolated steel frames were created and the nonlinear time history analysis was performed through a number of earthquake ground motions. The behaviour of the isolated frames was measured by the variation of isolator displacement, roof drift ratio, relative displacement, interstorey drift ratio, absolute acceleration, base shear, base moment, hysteretic curve, and dissipated energy. The benefits obtained through the adoption of the base isolation system were discussed. It was found that the seismic response of the base-isolated frames could be estimated accurately by adjusting the proper isolation period, yield strength ratio, and effective damping ratio for the case studied structures.〈/p〉〈/div〉 〈/div〉

Description: 〈p〉Publication date: October 2019〈/p〉 〈p〉〈b〉Source:〈/b〉 Soil Dynamics and Earthquake Engineering, Volume 125〈/p〉 〈p〉Author(s): Jinbao Yao, Rutao Zhao, Nan Zhang, Dujuan Yang〈/p〉 〈div xml:lang="en"〉 〈h5〉Abstract〈/h5〉 〈div〉 〈p〉An in-filled trench barrier is usually used to reduce the damages from train-induced environmental vibrations. To find the vibration isolation effect of an in-filled trench barrier, this paper analyses the reflection coefficients and transmission coefficients of the Rayleigh wave at the interface between in-filled trenches and the soil. In our calculation formulas of ground vibrations, a single point and a single frequency excitation, as well as multi-point and multi-frequency excitation, are simultaneously derived in a soil-in-filled-trench system.〈/p〉 〈p〉Using these formulas and a numerical analysis, the effects of an in-filled trench barrier on the environmental vibrations induced by running trains are analyzed. The results show that the reflection coefficients increase, while the transmission coefficients decrease, with the density and elastic modulus of the in-filled material. The vibration isolation effect is clearly better than that without trenches. In a certain width range, the transmission coefficient and vertical acceleration levels decrease with the increase of trench width. The influences of the transmission coefficient and the vibration isolation effects are not clear with the trenches’ depth variation. The vertical vibrations of the ground pick-up point are all smaller than those without in-filled trenches.〈/p〉 〈/div〉 〈/div〉

Description: 〈p〉Publication date: September 2019〈/p〉 〈p〉〈b〉Source:〈/b〉 Soil Dynamics and Earthquake Engineering, Volume 124〈/p〉 〈p〉Author(s): 〈/p〉

Description: 〈p〉Publication date: July 2019〈/p〉 〈p〉〈b〉Source:〈/b〉 Transportation Research Part F: Traffic Psychology and Behaviour, Volume 64〈/p〉 〈p〉Author(s): Kayla Fleskes, David S. Hurwitz〈/p〉 〈div xml:lang="en"〉 〈h5〉Abstract〈/h5〉 〈div〉〈p〉One proposed benefit of automated vehicles (AVs) is their potential to mitigate the occurrence of serious crashes due to human error or poor decision making while driving. However, there are still many concerns associated with the use of SAE Level 3 AVs, which require intervention by a human driver after a take-over request (TOR). These concerns intensify when vulnerable road users, such as bicyclists, are introduced to the driving environment. The objective of this research was to investigate how human drivers of AVs interact with bicyclists during a right-turn maneuver after receiving a TOR. Changes in driver performance, including visual attention and crash avoidance behavior, were measured by using a high-fidelity driving simulator, with 43 participants each completing 18 right-turn maneuvers. Three independent variables were studied: the bicyclist’s proximity to the intersection, the driver’s proximity from the intersection when the TOR was received, and the driver’s engagement in a distracting secondary task (a game on a tablet). In general, the results showed that the introduction of the secondary task led to decreased driver performance with respect to time-to-collision and the time that it took a driver to first identify the bicyclist on the roadway. When given more time to react before the intersection, drivers generally had safer interactions with the bicyclist.〈/p〉〈/div〉 〈/div〉 〈div xml:lang="en"〉 〈h5〉Graphical abstract〈/h5〉 〈div〉〈p〉〈figure〉〈img src="https://ars.els-cdn.com/content/image/1-s2.0-S136984781830411X-ga1.jpg" width="426" alt="Graphical abstract for this article" title=""〉〈/figure〉〈/p〉〈/div〉 〈/div〉

Description: 〈p〉Publication date: September 2019〈/p〉 〈p〉〈b〉Source:〈/b〉 Applied Thermal Engineering, Volume 160〈/p〉 〈p〉Author(s): Jingqi Tan, Jianjian Wei, Tao Jin〈/p〉 〈div xml:lang="en"〉 〈h5〉Abstract〈/h5〉 〈div〉〈p〉Onset and damping processes that characterize the transition of a thermoacoustic engine between the stationary and periodic oscillating states have attracted much research effort. In this work, the onset and damping characteristics of a closed two-phase thermoacoustic engine are investigated, where a regenerator is inserted between the cold and hot heat exchangers to reduce the irreversible loss caused by heat transfer. Additionally, a branch resonator, which consists of a load tube and a gas reservoir, is introduced to form the closed system and to adjust the acoustic field. A lumped parameter model is proposed to quantitatively analyze the performance of the thermoacoustic engine. Upon optimization, an onset temperature difference as low as 8.2 °C can be achieved in the experiments with R134a as the working fluid, which is the lowest one ever reported in the literatures. Besides, hysteresis phenomenon is found during the onset and damping processes. The present work aims to provide better understanding of the onset and damping behaviors of a two-phase thermoacoustic engine.〈/p〉〈/div〉 〈/div〉

Description: 〈p〉Publication date: October 2019〈/p〉 〈p〉〈b〉Source:〈/b〉 Soil Dynamics and Earthquake Engineering, Volume 125〈/p〉 〈p〉Author(s): Benshun Shao, Stephen A. Mahin, Victor Zayas〈/p〉 〈div xml:lang="en"〉 〈h5〉Abstract〈/h5〉 〈div〉〈p〉By interpreting the seismic responses of two seismically isolated low-rise case-study buildings probabilistically using FEMA P695 methodology, the study indicates for the design of seismically isolated structures, providing isolator capacities equal to risk-targeted maximum considered earthquake (MCE〈sub〉R〈/sub〉) demand does not achieve targeted levels of reliability specified in ASCE 7–16. To do so, isolation system capacities beyond average MCE〈sub〉R〈/sub〉 demand are required. The minimum required capacities for using three types of enhanced isolation system (isolator without displacement restraint, isolator combined with external hard-stopping mechanism, and isolator with internal stiffening behavior at large horizontal displacement) are calculated with nonlinear response history analysis following probabilistic framework for different design risk categories numerically. The results indicate that isolator displacement capacities ranging from 1.5 to 2.60 times the average MCE〈sub〉R〈/sub〉 demand and isolation system shear capacities ranging from 1.5 to 5 times the average MCE〈sub〉R〈/sub〉 demand are required, depending on seismic risk categories and isolation system types. The use of an isolator with internal stiffening behavior is an efficient option to provide the required capacities for achieving reliability goals, especially for high risk-category design.〈/p〉〈/div〉 〈/div〉

Description: 〈p〉Publication date: September 2019〈/p〉 〈p〉〈b〉Source:〈/b〉 Applied Thermal Engineering, Volume 160〈/p〉 〈p〉Author(s): Bin Zou, Yiqiang Jiang, Yang Yao, Hongxing Yang〈/p〉 〈div xml:lang="en"〉 〈h5〉Abstract〈/h5〉 〈div〉〈p〉Since various optical factors, including sunshape and optical errors, coexist in practice, their coupling effects on the PTC’s optical performance deserve in-depth explorations. Previous studies mainly focused on individual effects of several typical optical errors or simple description of optical errors using a unified Gaussian model. Thus, this study is committed to investigating the coupling effects of multiple optical factors on the PTC’s optical performance based on the theoretically individual characterization of each optical factor. The Monte Carlo Rays Tracing method was adopted, and the effective sunshape model was established for sampling of incident rays by convolving the incident sunshape model with the specularity error model. It is revealed that larger circumsolar ratio and specularity error produced more uniform heat flux distribution on the absorber. The advantage of high optical quality reflectors in improving optical efficiency was more outstanding in clearer weather. As circumsolar ratio was more than 0.2, improving specular quality to very high degree (〈3 mrad) reduced instead the optical efficiency. When tracking error and slope error were maintained respectively less than 4 mrad and 2 mrad, the weakening of optical efficiency was limited. The optical efficiency was more sensitive to slope error than to tracking error. The offset direction along positive Y-axis caused at maximum 2.19 times increase in heat flux density than that without optical errors, which causes threat of overheating to the absorber. When alignment error and tracking error were in the opposite direction, the optical loss could be compensated, whereas that in the same direction enlarged the optical loss. The slope error weakened the compensation effect and aggravated the weakening effect.〈/p〉〈/div〉 〈/div〉

Description: 〈p〉Publication date: Available online 8 July 2019〈/p〉 〈p〉〈b〉Source:〈/b〉 European Journal of Operational Research〈/p〉 〈p〉Author(s): K.T. Huynh〈/p〉 〈h5〉Abstract〈/h5〉 〈div〉〈p〉We are interested in the stochastic modeling of a condition-based maintained system subject to continuous deterioration and maintenance actions such as inspection, partial repair and replacement. The partial repair is assumed dependent on the past in the sense that it cannot bring the system back into a deterioration state better than the one reached at the last repair. Such a past-dependency can affect (〈em〉i〈/em〉) the selection of a type of maintenance actions, (〈em〉ii〈/em〉) the maintenance duration, (〈em〉iii〈/em〉) the deterioration level after a maintenance, and (〈em〉iv〈/em〉) the restarting system deterioration behavior. In this paper, all these effects are jointly considered in an unifying condition-based maintenance model on the basis of restarting deterioration states randomly sampled from a probability distribution truncated by the deterioration levels just before a current repair and just after the last repair/replacement. Using results from the semi-regenerative theory, the long-run maintenance cost rate is analytically derived. Numerous sensitivity studies illustrate the impacts of past-dependent partial repairs on the economic performance of the considered condition-based maintained system.〈/p〉〈/div〉

Description: 〈p〉Publication date: 1 October 2019〈/p〉 〈p〉〈b〉Source:〈/b〉 Electrochimica Acta, Volume 319〈/p〉 〈p〉Author(s): Jeonghoon Han, Changwoo Bae, Songhwa Chae, Dukhyun Choi, Sangmin Lee, Youngsuk Nam, Choongyeop Lee〈/p〉 〈div xml:lang="en"〉 〈h5〉Abstract〈/h5〉 〈div〉〈p〉Here we introduce the new approach to high-efficiency power generation from a salinity difference using conventional nanoporous Nafion membrane. When access areas on each side of nanoporous Nafion membrane are set to be asymmetric, the ratio of ionic current upon a voltage bias of the different polarity also becomes asymmetric, resulting in ionic diode phenomena. When this geometrical ionic diode effect is combined with a salinity gradient, it can help significantly improve the energy conversion efficiency from a salinity difference even under a hyper-saline environment with a large salinity difference, e.g. ∼41% conversion efficiency and ∼120 nW power generation with 1 M KCl and 1000-fold salinity difference, both of which are comparable with the best performances reported in the previous studies. We propose that the decrease in ion concentration polarization at a low salt concentration side is responsible for the enhanced power generation with the membrane having asymmetric access areas. Our approach is simple to implement and can be applicable to any nanoporous membrane to enhance the power generation from a salinity difference.〈/p〉〈/div〉 〈/div〉

Description: 〈p〉Publication date: 1 October 2019〈/p〉 〈p〉〈b〉Source:〈/b〉 Electrochimica Acta, Volume 319〈/p〉 〈p〉Author(s): Jialun Chen, Ping Tong, Lingting Huang, Zhonghua Yu, Dianping Tang〈/p〉 〈div xml:lang="en"〉 〈h5〉Abstract〈/h5〉 〈div〉〈p〉An interdigitated capacitance immunosensing system based enzymatic biocatalytic precipitation on micro-comb electrode was designed for the sensitive detection of prostate-specific antigen (PSA) by coupling Ti〈sub〉3〈/sub〉C〈sub〉2〈/sub〉 MXenes with tyramine signal amplification strategy. The immunosensor was prepared by immobilizing anti-PSA capture antibody on MXenes-coated interdigitated electrode, whereas gold nanoparticles heavily functionalized with horseradish peroxidase (HRP) and detection antibody were utilized as the signal-transducer tags. Introduction of interdigitated electrode was expected to enhance the sensitivity of capacitance immunosensor. This system mainly consisted of the sandwich-type immunoreaction, formation of tyramine-HRP repeats on gold nanoparticle and enzymatic biocatalytic precipitation. The concatenated HRP through the tyramine oxidized numerous 4-chloro-1-naphthol molecules into insoluble benzo-4-chlorohexadienone with the help of H〈sub〉2〈/sub〉O〈sub〉2〈/sub〉, and coated the modified immunosensor to keep free ions away from the electrode, thus causing the local alteration in the capacitance. Under optimum conditions, the change of the immunosensor in the capacitance increased with the increasing target PSA concentrations from 0.1 ng mL〈sup〉−1〈/sup〉 to 50 ng mL〈sup〉−1〈/sup〉 at a detection limit of 0.031 ng mL〈sup〉−1〈/sup〉. Moreover, the interdigitated capacitance immunosensor showed good reproducibility, high specificity and acceptable accuracy for the analysis of human serum specimens in comparison with those obtained from commercial human PSA ELISA kit. Importantly, Ti〈sub〉3〈/sub〉C〈sub〉2〈/sub〉 MXenes-based interdigitated capacitance transducer open new opportunities for protein diagnostics and biosecurity.〈/p〉〈/div〉 〈/div〉

Description: 〈p〉Publication date: 1 October 2019〈/p〉 〈p〉〈b〉Source:〈/b〉 Electrochimica Acta, Volume 319〈/p〉 〈p〉Author(s): Zhixu Jian, Honglei Li, Rui Cao, Heliang Zhou, Huaizhe Xu, Guangjin Zhao, Yalan Xing, Shichao Zhang〈/p〉 〈div xml:lang="en"〉 〈h5〉Abstract〈/h5〉 〈div〉〈p〉Confining the dissolution and diffusion of polysulfide is considered a key factor in the realization of high-performance lithium-sulfur battery. Here, we report a polydopamine (pDA) coated sulfur-carbon composite with a unique hierarchical tower-like structure (S-HTC@pDA) for lithium sulfur cathode. The internal layer by layer structure is capable of uniformly dispersing of sulfur, providing a continuous electronic conductive path and shortening the Li〈sup〉+〈/sup〉 transport distance, while the external pDA coating can inhibit the diffusion of polysulfide. Benefited from the smart design, the S-HTC@pDA electrode achieved an excellent cycling stability, realizing a high discharge capacity of 916 mAh g〈sup〉−1〈/sup〉 at the first cycle and a capacity retention of 79.4% after 500 cycles at 1 C. Therefore, this work provides a new concept in structure design for high performance lithium sulfur cathodes.〈/p〉〈/div〉 〈/div〉 〈h5〉Graphical abstract〈/h5〉 〈div〉〈p〉Here, we report a polydopamine (pDA) coated sulfur-carbon composite with a unique hierarchical tower-like structure (S-HTC@pDA) for lithium sulfur cathode. The internal layer by layer structure is capable of uniformly dispersing of sulfur, providing a continuous electronic conductive path and shortening the Li〈sup〉+〈/sup〉 transport distance, while the external pDA coating can inhibit the diffusion of polysulfide.〈figure〉〈img src="https://ars.els-cdn.com/content/image/1-s2.0-S0013468619312885-fx1.jpg" width="326" alt="Image 1" title="Image 1"〉〈/figure〉〈/p〉〈/div〉

Description: 〈p〉Publication date: Available online 8 July 2019〈/p〉 〈p〉〈b〉Source:〈/b〉 Quaternary International〈/p〉 〈p〉Author(s): Brian F. Codding, Adrian R. Whitaker, Nathan E. Stevens〈/p〉

Description: 〈p〉Publication date: 15 August 2019〈/p〉 〈p〉〈b〉Source:〈/b〉 Quaternary Science Reviews, Volume 218〈/p〉 〈p〉Author(s): Athanassios Athanassiou, Alexandra A.E. van der Geer, George A. Lyras〈/p〉 〈div xml:lang="en"〉 〈h5〉Abstract〈/h5〉 〈div〉〈p〉The Eastern Mediterranean islands, most of which belong to the Aegean archipelago, have a complex biogeographic history, which puts its stamp on their fauna and flora. A now extinct but most important faunal component, in terms of geographic spread and taxonomic diversity, are the elephants. The Eastern Mediterranean islands are particularly rich in Pleistocene endemic elephant localities, which preserve samples of extinct endemic populations. These were either descendants of the European straight-tusked elephant 〈em〉Palaeoloxodon antiquus〈/em〉 or the Southern mammoth, 〈em〉Mammuthus meridionalis〈/em〉. Their presence, history and palaeobiogeography has been documented only for Cyprus, Crete, Kasos, Rhodes, Tilos, Kýthera, Naxos, and Delos. For six other islands only anecdotal references exist in the literature: Kálymnos, Astypálaia, Milos, Sériphos, Kýthnos and Paros. Here, we provide an update on previously published specimens and taxa, describe previously undescribed specimens that were relocated in museum collections, as well as recently excavated specimens, and put these in the context of island palaeobiogeography. We conclude that dwarf elephants, endemic to their palaeo-island, lived on the islands of palaeo-Cyclades, Astypálaia, Crete, Kasos–Kárpathos–Saría, Tilos, Rhodes and Cyprus, whereas the elephants from Kephallenía, Kálymnos and Kýthera are indistinguishable on the species level from mainland 〈em〉Palaeoloxodon antiquus〈/em〉. Elephant fossils of unresolved taxonomic status are reported from five present-day islands. The Eastern Mediterranean endemic elephants likely derived from separate and independent colonisation events from the mainland. No island supported more than one proboscidean species at any time. We found that isolation had no effect on the degree of dwarfism, but that there exists a threshold of about 6–10 km distance between the island and the mainland, below which no dwarfism evolved, likely as a result of genetic contact with the mainland population. We also found that although island area is correlated with the degree of dwarfism in elephants, other factors, such as the level of interspecific competition, may limit this degree.〈/p〉〈/div〉 〈/div〉

Description: 〈p〉Publication date: Available online 8 July 2019〈/p〉 〈p〉〈b〉Source:〈/b〉 Remote Sensing of Environment〈/p〉 〈p〉Author(s): Julie A. Fortin, Jeffrey A. Cardille, Elijah Perez〈/p〉 〈div xml:lang="en"〉 〈h5〉Abstract〈/h5〉 〈div〉 〈p〉The ongoing march toward freely available, highly pre-processed satellite imagery has given both researchers and the public unprecedented access to a vast and varied data stream teeming with potential. Among many sources, the multi-decade Landsat archive is certainly the best known, but legacy and current data from other sensors is available as well through the USGS data portals: these include CBERS, ASTER, and more. Though the particular band combinations or non-global missions have made their integration into analyses more challenging, these data, in conjunction with the entire Landsat record, are available to contribute to multi-decade surveys of land-cover change.〈/p〉 〈p〉With the goal of tracing forest change through time near the Roosevelt River in the state of Mato Grosso, Brazil, we used BULC and Google Earth Engine to fuse information from 13 space-borne imagers capturing 140 images spanning 45 years. With high accuracy, the resulting time series of classifications shows the timing and location of land-use/land-cover change—both deforestation and regrowth—at sub-annual time scales. Accuracy estimates showed that the synthesized BULC classification time series was better than nearly all of the single-day image classifications, covering the entire study area at sub-annual frequency while reducing the impact of clouds and most unwanted noise as it fused information derived from a wide array of imaging platforms. The time series improved and gradually sharpened as the density of observations increased in recent decades, when there were three or more clear, higher-resolution views of a pixel annually from any sensor combination. In addition to detailing the methodology and results of multi-source data fusion with the BULC approach, this study raises timely points about integrating information from early satellite data sources and from sensors with footprints smaller than Landsat's. There are decades of research deriving sensor-specific techniques for classifying land use and land cover from a single image in a variety of settings. The BULC approach leverages the many successes of single-sensor research and can be used as a straightforward, complementary tool for blending many good-quality mapped classifications from disparate sources into a coherent, high-quality time series.〈/p〉 〈/div〉 〈/div〉

Description: 〈p〉Publication date: Available online 8 July 2019〈/p〉 〈p〉〈b〉Source:〈/b〉 Quaternary International〈/p〉 〈p〉Author(s): Xiaolin Ren, Duowen Mo, Michael Storozum, Ximena Lemoine, Yanyan Yu, Wanfa Gu, Xingshan Lei, Jiaqiang Zhang, Jianqing Lü, Tristram R. Kidder〈/p〉 〈div xml:lang="en"〉 〈h5〉Abstract〈/h5〉 〈div〉〈p〉Archaeologists have focused on the social conditions surrounding the development of urbanism around the world, however the environmental impact of these ancient cities remains unclear. In this paper, we present palynological data from the early Bronze Age city of Dongzhao, Henan Province, China. Our data indicate that vegetation change and the development of early urban settlements are closely linked, with the advent of urban development significantly accelerating deforestation and altering the composition of local vegetation communities. The pollen record from Dongzhao provides new evidence to support the claim that urban expansion, coupled with a drying climate and the expansion of agriculture, dramatically reconfigured the landscapes of Bronze Age China.〈/p〉〈/div〉 〈/div〉

Description: 〈p〉Publication date: 1 October 2019〈/p〉 〈p〉〈b〉Source:〈/b〉 Forest Ecology and Management, Volume 449〈/p〉 〈p〉Author(s): Yili Guo, Han Y.H. Chen, Azim U. Mallik, Bin Wang, Dongxing Li, Wusheng Xiang, Xiankun Li〈/p〉 〈div xml:lang="en"〉 〈h5〉Abstract〈/h5〉 〈div〉〈p〉Litterfall production is a major contributor to ecosystem net primary productivity and biogeochemical cycles. However, how various abiotic and biotic drivers influence litterfall production in heterogeneous natural forests is still debated. We used structural equation models (SEM) to test the direct and indirect effects of tree species diversity, tree diameter variation, stand basal area, and abiotic drivers (canopy exposure, elevation, slope, convexity, aspect, topographic wetness index and altitude above channel) on annual litterfall production in a heterogeneous tropical karst seasonal rainforest in Southern China. The SEM with tree species diversity, tree diameter variation, stand basal area, and abiotic drivers accounted for 43.4% of the variation in annual litterfall production. Tree species diversity and stand basal area had positive direct effects, while tree diameter variation had a negative direct effect on annual litterfall production. Tree species diversity had no significant effect on tree diameter variation nor stand basal area. Both annual litterfall production and tree species diversity decreased directly with water availability, while canopy exposure positively affected annual litterfall production but not tree species diversity. Our results indicate that the positive relationship between tree species diversity and litterfall production did not result from the effects of species diversity on canopy packing; instead, it appears that increasing soil water availability simultaneously reduce tree species diversity and annual litterfall production in the tropical karst seasonal rainforest.〈/p〉〈/div〉 〈/div〉

Description: 〈p〉Publication date: 15 September 2019〈/p〉 〈p〉〈b〉Source:〈/b〉 Precambrian Research, Volume 332〈/p〉 〈p〉Author(s): Farzaneh Shakerardakani, Xian-Hua Li, Xiao-Xiao Ling, Jiao Li, Guo-Qiang Tang, Yu Liu, Behzad Monfaredi〈/p〉 〈div xml:lang="en"〉 〈h5〉Abstract〈/h5〉 〈div〉〈p〉High-precision secondary-ion mass spectrometry (SIMS) U–Pb and Hf–O isotopic microanalyses of zircons from the central Sanandaj–Sirjan metamorphic zone (SSMZ) of the Zagros orogen, Iran, provide evidence of the presence of 2.7 Ga xenocrystic zircons, suggesting that the SSMZ records Neoarchean crustal components that have not previously been reported in Iran. The two amphibolite samples analyzed from the Muteh–Golpaygan metamorphic complex during this study include one sample (GQ-10) that yielded xenocrystic zircons with ages clustered around 〈em〉ca〈/em〉 2.7 Ga. The second sample (GC-15) contains zircons that show two distinct xenocrystic zircon domains with ages of (i) 〈em〉ca〈/em〉 2.7 and 2.5 Ga, and (ii) 〈em〉ca〈/em〉 52 Ma. The 〈em〉ca〈/em〉 2.7 Ga zircons and zircon domains have homogeneous, mantle-like δ〈sup〉18〈/sup〉O values with a mean of 6.10 ± 0.69‰. They have εHf(t) values that vary between +0.2 to +6.8 with T〈sub〉DM〈/sub〉〈sup〉C〈/sup〉 ages of 3.1–2.7 Ga, suggesting they crystallized from granitoid melts derived from juvenile components. However, the younger 〈em〉ca〈/em〉 2.5 Ga zircons yield an average δ〈sup〉18〈/sup〉O value of 6.17 ± 0.24‰ and have evolved Hf isotopic compositions (εHf(t) −0.8 to −3.4; T〈sub〉DM〈/sub〉〈sup〉C〈/sup〉 = 3.2–3.1 Ga), indicating that the older crust in this region underwent more intense later reworking than is the case for crustal material formed at 〈em〉ca〈/em〉 2.7 Ga. These data provide evidence of Neoarchean basement rocks in this region, indicating that the SSMZ records ancient crustal growth events. The youngest 〈em〉ca〈/em〉 52 Ma xenocrystic zircons within these samples most likely reflect the late Paleocene–Eocene magmatic ‘flare-up’ within Iran. These zircons have slightly elevated δ〈sup〉18〈/sup〉O values (7.69 ± 0.21‰) and negative Hf isotopic compositions (εHf(t) −8.3 to −12.1; T〈sub〉DM〈/sub〉〈sup〉C〈/sup〉 = 1.9–1.6 Ga), suggesting intensive crustal reworking at 〈em〉ca〈/em〉 50 Ma.〈/p〉〈/div〉 〈/div〉

Description: 〈p〉Publication date: 15 September 2019〈/p〉 〈p〉〈b〉Source:〈/b〉 Precambrian Research, Volume 332〈/p〉 〈p〉Author(s): Kelsey G. Lamothe, Paul F. Hoffman, J. Wilder Greenman, Galen P. Halverson〈/p〉 〈div xml:lang="en"〉 〈h5〉Abstract〈/h5〉 〈div〉〈p〉The Islay carbon isotope anomaly is a late Tonian negative δ〈sup〉13〈/sup〉C excursion that has been documented in marine carbonates globally. It has in the past been thought to be causally linked to the onset of Cryogenian glaciation ca. 717 Ma. However, recent work suggests that this anomaly is instead closer to ca. 739–735 Ma and that it may be one of two distinct late Tonian carbon isotope anomalies. Here we present the litho- and chemo-stratigraphy of the late Tonian Ugab Subgroup of the Otavi/Swakop Group in northwestern Namibia. Carbon isotope data from two separate outcrop belts, the Summas Mountains and the Vrede Domes, indicate that the Ugab Subgroup strata exposed in the former inlier are older than those of the latter, with only approximately 100 m of stratigraphic overlap. We use detailed measured sections to develop a sequence stratigraphic framework for the Ugab Subgroup in each outcrop belt, and correlate strata across the two exposures to construct a composite carbonate δ〈sup〉13〈/sup〉C record for the late Tonian in Namibia. This carbon isotope profile of the Ugab Subgroup shows two separate pre-Sturtian negative anomalies, consistent with findings in northern Canada, Svalbard, Scotland, and Ethiopia. Our results are an important contribution to the pre-Cryogenian carbon isotope record, as these data may serve as the first definitive documentation of both anomalies within a single basin.〈/p〉〈/div〉 〈/div〉

Description: 〈p〉Publication date: 15 September 2019〈/p〉 〈p〉〈b〉Source:〈/b〉 Precambrian Research, Volume 332〈/p〉 〈p〉Author(s): V.S. Shatsky, Q. Wang, S.Yu. Skuzovatov, A.L. Ragozin〈/p〉 〈div xml:lang="en"〉 〈h5〉Abstract〈/h5〉 〈div〉〈p〉To clarify the tectonic-thermal evolution of the Anabar tectonic province in the central Siberian Craton, we performed an isotope-geochemical study of 20 xenoliths from the Udachnaya, Zarnitsa, and Komsomolskaya kimberlite pipes to represent different crustal levels. Most mafic granulites have Proterozoic Nd model ages and geochemical characteristics close to those of intraplate basalts, whereas some mafic and intermediate granulites with Archean model ages exhibit geochemical features of supra-subduction ophiolitic basalts. Analysis of U-Pb ages and hafnium isotopic composition of zircon indicates that the main tectonic-thermal events modified the crust at 2.7 and 1.9–1.8 Ga, which is consistent with ages of mantle depletion events from previous studies. All zircons have Archean Hf model ages (〈math xmlns:mml="http://www.w3.org/1998/Math/MathML" altimg="si2.svg"〉〈mrow〉〈msubsup〉〈mi〉T〈/mi〉〈mrow〉〈mi mathvariant="italic"〉DM〈/mi〉〈/mrow〉〈mi〉C〈/mi〉〈/msubsup〉〈mspace width=".25em"〉〈/mspace〉〈mn〉3.6〈/mn〉〈mo linebreak="badbreak" linebreakstyle="after"〉-〈/mo〉〈/mrow〉〈/math〉3.2 Ga). Overall, thermal events with ages of 2.9–2.8, 2.7, 2.4, 1.97 and 1.8 Ga have remarkable influence on the studied zircons. Tectono-thermal events at 2.4 1.97, 1.9 and 1.8 Ga with no addition of juvenile material are recorded by zircons from xenoliths of mafic and intermediate granulites and metadiorites. A compilation of isotope-geochemical data demonstrates that instead of age-stratified, the crust of the Anabar tectonic province consists of variably reworked Paleoarchean rocks and juvenile Proterozoic rocks at all crustal levels. Hence the crust and mantle of the Siberian Craton has been coupled since the Paleoarchean.〈/p〉〈/div〉 〈/div〉

Description: 〈p〉Publication date: Available online 8 July 2019〈/p〉 〈p〉〈b〉Source:〈/b〉 Precambrian Research〈/p〉 〈p〉Author(s): B.R. Choudhary, R.E. Ernst, Y-G. Xu, D.A.D. Evans, M. de Kock, J.G. Meert, A. Ruiz, G.A. Lima〈/p〉 〈div xml:lang="en"〉 〈h5〉Abstract〈/h5〉 〈div〉 〈p〉1110 Ma Large Igneous Province (LIP) fragments in the Kalahari craton, southern Africa (Umkondo LIP); Dronning Maud Land, Antarctica; Bundelkhand portion of Indian craton (Mahoba dolerite dykes); Congo craton (Huila-Epembe dolerite dykes); and Amazonia (Rincon del Tigre-Huanchaca LIP) have been reconstructed as a single LIP with plume centre beneath the NW part of the Kalahari Craton. This paper offers the best estimates for the paleoposition of the〈/p〉 〈p〉Indian and Amazonian cratons along with conjoined Kalahari-SF/Congo reconstruction. This 1110 Ma mafic magmatism is dominantly tholeiitic, ranging from basalt to andesitic basalt in composition, generated over a range of mantle melting depths [(Gd/Yb)N =1.2 to 2.3], exhibit low to high contamination with crustal components (negative Nb anomalies, eNd (0 to -12), and elevated Th/Yb). The data fall into two Groups based on TiO2 content, with Group 1 (low Ti) of andesitic basalt composition, and Group 2 (high Ti) exhibiting a basaltic affinity. Group 1 magmas were generated in the spinel lherzolite field followed by significant contamination likely during passage through metasomatised lithospheric mantle in crustal magma chambers. A greater melting depth reaching into the garnet lherzolite field is proposed for the Group 2 magmas. The majority of Group 2 units are located in the Kalahari and Congo cratons, and this reflects onset of deeper melting closer to the interpreted plume axis in our reconstruction.〈/p〉 〈/div〉 〈/div〉

Description: 〈p〉Publication date: November 2019〈/p〉 〈p〉〈b〉Source:〈/b〉 Computers & Geosciences, Volume 132〈/p〉 〈p〉Author(s): T. Carlotto, P.L.B. Chaffe〈/p〉 〈h5〉Abstract〈/h5〉 〈div〉〈p〉Streamflow recession analysis is crucial for understanding how catchments release water in periods of drought and therefore is important for water resources planning and management. Despite there being several theories on how to model recession curves, few studies compare the different approaches to that problem. In this work, we developed the Master Recession Curve Parameterization tool (MRCPtool), which brings together a set of automated methods for the analysis of recession periods based only on streamflow data. The methods include: (i) hydrograph separation using numerical filters; (ii) automatic extraction of recession periods; (iii) creation of the MRC with the matching strip method; (iv) creation of the MRC for different flow classes defined from the flow duration curve; (v) analysis of flow recession rates 〈math xmlns:mml="http://www.w3.org/1998/Math/MathML" display="inline" altimg="si1.svg"〉〈mrow〉〈mo〉(〈/mo〉〈mo linebreak="goodbreak" linebreakstyle="after"〉−〈/mo〉〈mi〉d〈/mi〉〈mi〉Q〈/mi〉〈mo〉∕〈/mo〉〈mi〉d〈/mi〉〈mi〉t〈/mi〉〈mo〉)〈/mo〉〈/mrow〉〈/math〉 as a function of flow 〈math xmlns:mml="http://www.w3.org/1998/Math/MathML" display="inline" altimg="si2.svg"〉〈mrow〉〈mo〉(〈/mo〉〈mi〉Q〈/mi〉〈mo〉)〈/mo〉〈/mrow〉〈/math〉 and (vi) creation of the MRC from simulated recession curves with different analytical approaches, including linear and nonlinear models. The MRCPtool contains a graphical user interface developed in MATLAB software that facilitates the analysis of streamflow datasets. Finally, we present an example application of the MRCPtool using a streamflow dataset of 44 years. The MRCPtool is an open source tool that can be downloaded from the site: 〈a href="http://www.labhidro.ufsc.br/static/software/MRCPtool.rar" target="_blank"〉http://www.labhidro.ufsc.br/static/software/MRCPtool.rar〈/a〉.〈/p〉〈/div〉

Description: 〈p〉Publication date: Available online 8 July 2019〈/p〉 〈p〉〈b〉Source:〈/b〉 Precambrian Research〈/p〉 〈p〉Author(s): Vladimir N. Sergeev, J. William Schopf, Anatoliy B. Kudryavtsev〈/p〉 〈div xml:lang="en"〉 〈h5〉Abstract〈/h5〉 〈div〉 〈p〉Subtidal cherts from phosphorite-bearing basal strata of the Early Cambrian Shabakta (Dzhylandy) Formation, Tamda Group of the Maly Karatau Range of South Kazakhstan, contain a diverse assemblage of acanthomorph acritarchs and other well-preserved organic-walled microfossils. Acanthomorphs of the Shabakta lowermost layers are taxonomically essentially identical to those of many similarly aged Early Cambrian organic-walled compression-preserved and permineralized microbiotas preserved in rocks deposited in relatively open marine settings and are biostratigraphically correlative with acanthomorph-containing microfloral assemblages of the Vergale and Rausve Horizons (Regional Stages) of the East European Platform as well as with other assemblages known worldwide from the upper Atdabanian (Series 2 of the International Union of Geological Sciences [IUGS]). Although lower Atdabanian deposits of the Talsy (Lükati) horizon are missing from the Maly Karatau succession studied here, Nemakit-Daldynian through Tommotian (the IUGS Terranovian) microbiotas both of the Shabakta-underlying Berkuta Member of the Kyrshabakta Formation and phosphoritic Chulaktau Formation are comparable to those of the pre-trilobite Rovno and Lontova Horizons (Regional Stages) of the East European Platform. Thus, the phosphatized and chert-permineralized Shabakta assemblages date from of the Early Cambrian part of the Precambrian-Cambrian phosphogenic event, an interpretation supported also by associated small shelly fossils.〈/p〉 〈p〉The studies reported here of the Shabakta microfossils – based on the use of optical microscopy, confocal laser scanning microscopy (CLSM) and Raman spectroscopy – provide information in three dimensions at high spatial resolution about their organismal morphology, cellular anatomy, kerogenous composition, taphonomy, and mode and fidelity of preservation. The combined use of CLSM and Raman, techniques introduced to Precambrian paleobiology only rather recently, is shown to reveal morphological characters of taxonomic, biostratigraphic and palaeoenvironmental significance.〈/p〉 〈/div〉 〈/div〉 〈div xml:lang="en"〉 〈h5〉Graphical abstract〈/h5〉 〈div〉〈p〉〈figure〉〈img src="https://ars.els-cdn.com/content/image/1-s2.0-S0301926818306260-ga1.jpg" width="274" alt="Graphical abstract for this article" title=""〉〈/figure〉〈/p〉〈/div〉 〈/div〉

Description: 〈p〉Publication date: December 2019〈/p〉 〈p〉〈b〉Source:〈/b〉 Marine and Petroleum Geology, Volume 110〈/p〉 〈p〉Author(s): Walid A. Makled, Ahmed A. Abd El Ghany, Soheir I. Soliman〈/p〉 〈div xml:lang="en"〉 〈h5〉Abstract〈/h5〉 〈div〉〈p〉Productivity, redox conditions and sedimentation rate constrain the enrichments of organic matters and under suitable conditions they can trigger larger enrichments. These parameters are tracked in the subsurface Miocene sediments in four wells on east to west transect across north Sinai. These wells are Abu Roda-1, Misfaq-1, Teffah-1 and Einab-1. The Miocene sections cover the Aquitanian, Burdigalian, Langhian, Serravalian and Tortonian. The tracking is based on the proxies of planktonic and benthic foraminifera that offer many solutions in the application of the equations used to calculate these parameters. The first of these parameters is the sedimentation rate which is calculated for different time segments based on the planktonic foraminifera bioevents. The sedimentation rates are correlated throughout the basin. The second parameter is the water depth that is obtained from conversion of the scores of component 1 resulted during the routine statistical analysis of the benthic foraminifera by cluster and principal component analyses. These analyses are used also in assessment of redox condition and eutrophication. The sedimentation rates and water paleobathymetry alongside the measured C〈sub〉org〈/sub〉 are used to calculate the paleoproductivity and to determine four stratigraphic sequences (Seq1, Seq2, Seq3 and Seq4). The tracking of these parameters reveal higher productivity levels in the Seq1 (Aquitanian and Burdigalian) accompanied with dysoxic and mesotrophic conditions, however the lower sedimentation rates are not optimum to stimulate enough burial efficiency that reduced values of C〈sub〉org〈/sub〉. In the younger sequences (Seq2-4), the higher sedimentation rates increase the burial efficiency and values of C〈sub〉org〈/sub〉 despite the lower paleoproductivity and oxic oligotrphic conditions.〈/p〉〈/div〉 〈/div〉

Description: 〈p〉Publication date: August 2019〈/p〉 〈p〉〈b〉Source:〈/b〉 Solar Energy, Volume 188〈/p〉 〈p〉Author(s): Naser Abdi, Yaser Abdi, Zahra Alemipour〈/p〉

Description: 〈p〉Publication date: December 2019〈/p〉 〈p〉〈b〉Source:〈/b〉 Marine and Petroleum Geology, Volume 110〈/p〉 〈p〉Author(s): Marwa Yousef, Mohamed Yousef, Adel Sehim〈/p〉 〈div xml:lang="en"〉 〈h5〉Abstract〈/h5〉 〈div〉〈p〉High-quality three-dimensional (3D) seismic reflection and borehole data are used to characterize in detail the structural style and evolution of inversion structures in Horus oil field. This field lies in the central part of Alamein Basin, northern Western Desert of Egypt, in the hanging-wall of a major Jurassic-Early Cretaceous normal fault. This fault delineates the northwestern margin of the basin and extends in an ENE-WSW direction, bounding a half-graben trough in its hanging-wall. This trough had continued subsidence during Early Cretaceous time with depositional thickening of the Lower Cretaceous Alam el Bueib Formation. Fault displacement had ceased near the top of Barremian level. Aptian-Lower Senonian seismically traced levels show a major NE-plunging asymmetrical anticline overlying the Jurassic-Barremian half-graben. This anticline is sub-parallel to the inherited Jurassic rifting fault. At shallower Cretaceous levels, this fault is replaced by a set of WNW-ESE-trending en echelon faults of considerable displacements, which probably indicates a strike-slip component of deformation. These faults display normal separation on all displaced stratigraphic levels and tip upwards in the upper part of the Upper Cretaceous succession. This marks a considerable change in the tectonic mode of the area. NW-SE extensional faults were developed perpendicular to the fold axis, dissecting the anticline into several blocks entrapping hydrocarbons. Detailed seismic structural analysis of growth strata indicates that the fold initiated in Early Senonian time was associated with the inversion of the earlier Jurassic-Barremian half-graben. This basin inversion is attributed to the Syrian-Arc event that dominated North Africa during the Late Cretaceous time and continued through to the Early Miocene. Low fold amplitude coupled with normal displacements on the deep-seated ENE-WSW-trending Jurassic-Barremian fault indicate a mild phase of positive inversion. The Upper Senonian-Eocene stratigraphic sequences increased in thickness in the back-troughs that were associated with basin inversion.〈/p〉〈/div〉 〈/div〉 〈h5〉Graphical abstract〈/h5〉 〈div〉〈p〉〈figure〉〈img src="https://ars.els-cdn.com/content/image/1-s2.0-S0264817219303198-fx1.jpg" width="57" alt="Image 1" title="Image 1"〉〈/figure〉〈/p〉〈/div〉

Description: 〈p〉Publication date: 1 November 2019〈/p〉 〈p〉〈b〉Source:〈/b〉 Geoderma, Volume 353〈/p〉 〈p〉Author(s): Jingzhe Wang, Jianli Ding, Danlin Yu, Xuankai Ma, Zipeng Zhang, Xiangyu Ge, Dexiong Teng, Xiaohang Li, Jing Liang, Ivan Lizaga, Xiangyue Chen, Lin Yuan, Yahui Guo〈/p〉 〈div xml:lang="en"〉 〈h5〉Abstract〈/h5〉 〈div〉〈p〉Soil salinization is one of the most important causes for land degradation and desertification and is an important threat to land management, farming activities, water quality, and sustainable development in arid and semi-arid areas. Soil salinization is often characterized with significant spatiotemporal dynamics. The salt-affected soil is predominant in the Ebinur Lake region in the Northwestern China. However, detailed local soil salinity information is ambiguous at the best due to limited monitoring techniques. Nowadays, the availability of Multi-Spectral Instrument (MSI) onboard Sentinel-2, offers unprecedented perspectives for the monitoring and mapping of soil salinity. The use of MSI data is an innovative attempt for salinity detection in arid land. We hypothesize that field observations and MSI data and MSI data-derived spectral indices using the partial least square regression (PLSR) approach will yield fairly accurate regional salinity map. Based on electrical conductivity of 1:5 soil:water extract (EC) of 72 ground-truth measurements (out of 116 sample sites) and various spectral parameters, such as satellite band reflectance, published satellite salinity indices, red-edge indices, newly constructed two-band indices, and three-band indices from MSI data, we built a few inversion models in an attempt to produce the regional salinity maps. Different algorithms including Pearson correlation coefficient method (PCC), variable importance in projection (VIP), Gray relational analysis (GRA), and random forest (RF) were applied for variable selection. The results suggest that both the newly proposed normalized difference index (NDI) [(B12 − B7) / (B12 + B7)] and three-band index (TBI4) [(B12 − B3) / (B3 − B11)] show a better correlation with validation data and could be applied to estimate the soil salinity in the Ebinur Lake region. The established models were validated using the remaining 44 independent ground-based measurements. The RF-PLSR model performed the best across the five models with R〈sup〉2〈/sup〉〈sub〉V〈/sub〉, RMSE〈sub〉V〈/sub〉, and RPD of 0.92, 7.58 dS m〈sup〉−1〈/sup〉, and 2.36, respectively. The result from this model was then used to map the soil salinity over the study area. Our analyses suggest that soil salinization changes quite significantly in different seasons. Specifically, soil salinity in the dry season was higher than in the wet season, mostly in the lake area and nearby shores. We contend that the results from the study will be useful for soil salinization monitoring and land reclamation in arid or semi-arid regions outside the current study area.〈/p〉〈/div〉 〈/div〉

Description: 〈p〉Publication date: December 2019〈/p〉 〈p〉〈b〉Source:〈/b〉 Marine and Petroleum Geology, Volume 110〈/p〉 〈p〉Author(s): Shuheng Du, Yapu Zhao, Jun Jin, Gen Kou, Yongmin Shi, Xianfu Huang〈/p〉 〈div xml:lang="en"〉 〈h5〉Abstract〈/h5〉 〈div〉〈p〉Perthite is a special type of skeleton mineral in tight oil sandstone which cannot be ignored. However, few attention was paid to the secondary pores in perthite and their contributions in tight oil reservoir. This study reveals the perthite's significance in unconventional oil flow characterizes comprehensively and quantitativel by combining the Field Emission Scanning Electron Microscope (FE-SEM) with high resolution, Energy Dispersive Spectrometer (EDS) analysis, high precision image processing, comprehensive parameters construction and calculation. Typical perthite samples of Chang 7 tight oil reservoir of Ordos basin were selected for this study. Our results demonstrate that the growth of K-feldspar and Na-feldspar in perthite is complementary. The mixing process of the two types of stripes promotes each other rather than inhibiting each other. As to the development of secondary pores of perthite, there are clear differences in the area and number of pores, medium differences in the porosity, radius and perimeter, and small differences in other parameters. The more regular and uniform growth of Na-feldspar, the more likely the perthite is to form regular and normalized secondary pore. At least 56.7% of the secondary pore of perthite contributes to oil flow in the process of oil migration or development, and its scientific significance cannot be ignored. The conclusion could provide the geological basis for the effective development of the unconventional hydrocarbon reservoirs.〈/p〉〈/div〉 〈/div〉

Description: 〈p〉Publication date: Available online 9 July 2019〈/p〉 〈p〉〈b〉Source:〈/b〉 Geochemistry〈/p〉 〈p〉Author(s): Yu Zhang, Xianghong Meng, Duoyun Wang〈/p〉 〈h5〉Abstract〈/h5〉 〈div〉〈p〉The Ordos Basin is a large interior continental sedimentary basin in western China； its Mesozoic evolution was controlled by surrounding orogenic belts. To constrain the evolution of the southern Ordos Basin, four samples from the southern Ordos Basin were analyzed for U-Pb ages. Similar detrital zircon U-Pb age patterns of the samples suggest no provenance change occurred during the Middle Triassic. Detrital zircons from the samples are divided into three major groups based on their U-Pb ages: 360-250 Ma, 2000-1600 Ma and 2800-2200 Ma. The first group of zircons is consistent with Paleozoic igneous zircons from the northern margin of the North China Craton (NCC). Detrital zircons of the second and third groups are likely derived from the basement of the NCC northern margin. In the Middle Triassic, detritus from the Qinling Orogenic belt may only have reached the piedmont deep depression. The absence of the Qilian Mountain source suggests that the Ordos Basin may not have been connected with the Hexi Corridor Basin in the Middle Triassic. Combining our results with those of previous studies, we suggest that the southern borderline of the Ordos Basin may not have reached the Qinling Orogenic Belt. The northern margin of the NCC, the Qinling Orogenic Belt and the pre-Middle Triassic sedimentary rocks of the eastern NCC provided sources for the Southern Ordos Basin in the Late Triassic. The rapid uplift of the Qinling Orogenic belt occurred in the Late Triassic. This event was response to collision between the NCC and the South China Block. The deposition and evolution of the Ordos Basin were controlled by the Indosinian movement. The change in source areas for the Southern Ordos Basin was closely related to the development and evolution of the Qinling Orogenic Belt. The Qinling Orogenic Belt shows good coupling with the sedimentation and structures of the Southern Ordos Basin.〈/p〉〈/div〉

Description: 〈p〉Publication date: October 2019〈/p〉 〈p〉〈b〉Source:〈/b〉 Journal of Applied Geophysics, Volume 169〈/p〉 〈p〉Author(s): Zhiqu Lu, Glenn V. Wilson, Mark W. Shankle〈/p〉 〈div xml:lang="en"〉 〈h5〉Abstract〈/h5〉 〈div〉〈p〉For soil exploration in the vadose zone, a high-frequency multi-channel analysis of surface waves (HF-MASW) method with three enhanced techniques has been developed. In this paper, we apply this enhanced HF-MASW method to re-process field testing data that were collected over the past several years on five different sites. These sites are selected for their different soil properties and data acquisition configurations. The derived overtone images, extracted dispersion curves, and inverted soil profiles of these soil sites are shown and discussed. Penetration tests were conducted and comparisons are made between the soil profiles taken from the HF-MASW tests and those from the penetration tests. One of the objectives of the paper is to determine the optimal data acquisition parameters, including the source parameters and sensor array geometric configuration through the discussions of these case studies. Practical concerns of the HF-MASW method and lessons learnt from these tests are addressed. Recommendations for data acquisition, signal processing, and inversion are provided.〈/p〉〈/div〉 〈/div〉

Description: 〈p〉Publication date: August 2019〈/p〉 〈p〉〈b〉Source:〈/b〉 Solar Energy, Volume 188〈/p〉 〈p〉Author(s): Smajil Halilovic, Jamie M. Bright, Wiebke Herzberg, Sven Killinger〈/p〉 〈div xml:lang="en"〉 〈h5〉Abstract〈/h5〉 〈div〉〈p〉Knowledge of horizontal solar irradiance is crucial for the nowcasting and forecasting of generated photovoltaic (PV) power. High quality irradiance measurement devices, however, are typically not collocated with PV systems. The lack of measurements can be compensated by numerical weather models or satellite-derived products, but they provide only limited temporal and spatial resolutions. Another possibility is to directly use PV systems as irradiance sensors, since the measured PV power is a good indicator of incoming solar irradiance. The challenging part in this procedure is the computation of the global horizontal irradiance 〈math xmlns:mml="http://www.w3.org/1998/Math/MathML" altimg="si233.svg"〉〈mrow〉〈msub〉〈mrow〉〈mi〉G〈/mi〉〈/mrow〉〈mrow〉〈mi〉h〈/mi〉〈/mrow〉〈/msub〉〈/mrow〉〈/math〉 from the global tilted irradiance 〈math xmlns:mml="http://www.w3.org/1998/Math/MathML" altimg="si234.svg"〉〈mrow〉〈msub〉〈mrow〉〈mi〉G〈/mi〉〈/mrow〉〈mrow〉〈mi〉c〈/mi〉〈/mrow〉〈/msub〉〈/mrow〉〈/math〉, because a combination of decomposition and transposition models is not analytically invertible. Hence, the majority of existing solutions to this problem are numerical procedures. In this paper, an analytical approach to compute 〈math xmlns:mml="http://www.w3.org/1998/Math/MathML" altimg="si235.svg"〉〈mrow〉〈msub〉〈mrow〉〈mi〉G〈/mi〉〈/mrow〉〈mrow〉〈mi〉h〈/mi〉〈/mrow〉〈/msub〉〈/mrow〉〈/math〉 from 〈math xmlns:mml="http://www.w3.org/1998/Math/MathML" altimg="si236.svg"〉〈mrow〉〈msub〉〈mrow〉〈mi〉G〈/mi〉〈/mrow〉〈mrow〉〈mi〉c〈/mi〉〈/mrow〉〈/msub〉〈/mrow〉〈/math〉 is presented. The comparison of the proposed approach with one of the existing iterative (numerical) approaches shows promising results. When applied to 1-min data at four different locations, the new approach outperforms the iterative procedure by up to 9% in terms of the relative root mean square error (rRMSE) for east/west module’s orientations, and performs slightly better with the south orientation. Moreover, the new approach provides results in less than 1 s, whereas the iterative procedure requires more than 20 min for a one year of data. An open source R-script of the new approach is also publicly available and provided as supplementary material.〈/p〉〈/div〉 〈/div〉

Description: 〈p〉Publication date: September 2019〈/p〉 〈p〉〈b〉Source:〈/b〉 Free Radical Biology and Medicine, Volume 141〈/p〉 〈p〉Author(s): Chao Wang, Yuan Yuan, Jie Wu, Yuanlin Zhao, Xing Gao, Yihua Chen, Chao Sun, Liming Xiao, Pengfei Zheng, Peizhen Hu, Zengshan Li, Zhe Wang, Jing Ye, Lijun Zhang〈/p〉 〈div xml:lang="en"〉 〈h5〉Abstract〈/h5〉 〈div〉〈p〉While cardiac hypertrophy and heart failure are accompanied by significant alterations in energy metabolism, more than 50–70% of energy is obtained from fatty acid β-oxidation (FAO) in adult hearts under physiological conditions. Plin5 is involved in the metabolism of lipid droplets (LDs) and is highly abundant in oxidative tissues including heart, liver and skeletal muscle. Plin5 protects the storage of triglyceride (TG) in LDs by inhibiting lipolysis, thereby suppressing excess FAO and preventing excessive oxidative stress in the heart. In this study, we investigated the roles of Plin5 in cardiac hypertrophy and heart failure in mice treated with transverse aortic constriction (TAC). The results indicated that Plin5 deficiency aggravated myocardial hypertrophy in the TAC-treated mice and exacerbated the TAC-induced heart failure. We also found that Plin5 deficiency reduced the cardiac lipid accumulation and upregulated the levels of PPARα and PGC-1α, which stimulate mitochondrial proliferation. Moreover, Plin5 deficiency aggravated the TAC-induced oxidative stress. We consistently found that Plin5 knockdown disrupted TG storage and elevated FAO and lipolysis in H9C2 rat cardiomyocytes. In addition, Plin5 knockdown also provoked mitochondrial proliferation and lipotoxic injury in H9C2 cells. In conclusion, Plin5 deficiency increases myocardial lipolysis, elevates FAO and oxidative burden, and thereby exacerbates cardiac hypertrophy and heart failure in TAC-treated mice.〈/p〉〈/div〉 〈/div〉 〈h5〉Graphical abstract〈/h5〉 〈div〉〈p〉〈figure〉〈img src="https://ars.els-cdn.com/content/image/1-s2.0-S089158491930471X-fx1.jpg" width="336" alt="Image 1" title="Image 1"〉〈/figure〉〈/p〉〈/div〉

Description: Cover illustration The Wawel Dragon above Krakow. Illustration by Apolonia Stankiewicz originally published in page 3 of Baïka magazine, issue n°14, March 2019.

Description: Tonicity‐responsive enhancer binding protein (TonEBP) is a widely expressed transcription factor and is important in the regulation of inflammatory cytokines. Here, we have identified TonEBP expression in the hypothalamus, which is particularly high in proopiomelanocortin (POMC) neurons. TonEBP overexpression stimulates POMC transcription, and TonEBP haploinsufficiency in TonEBP (+/−) mice results in a decrease in hypothalamic POMC expression. TonEBP (+/−) mice show reduced sickness responses, which include anorexia and hyperthermia, that are initially induced by tumor necrosis factor (TNF)‐α. TonEBP (+/−) mice also show lower levels of TNF‐α‐induced hypothalamic expression of POMC and pro‐inflammatory cytokines. These results suggest that TonEBP is an important molecular regulator in the development of inflammatory sickness responses through the control of POMC and pro‐inflammatory cytokine expression in the hypothalamus.

Description: 〈p〉Publication date: 15 December 2019〈/p〉 〈p〉〈b〉Source:〈/b〉 Lithos, Volumes 346–347〈/p〉 〈p〉Author(s): Rohit Pandey, Ashutosh Pandey, N.V. Chalapathi Rao, B. Belyatsky, A.K. Choudhary, B. Lehmann, Dinesh Pandit, Prashant Dhote〈/p〉 〈div xml:lang="en"〉 〈h5〉Abstract〈/h5〉 〈div〉〈p〉We present petrology, geochemistry and radiogenic isotope (Sr and Nd) data of thirteen post-Deccan lamprophyre dykes in the Narmada rift zone from the Chhotaudepur alkaline province of the Deccan Large Igneous Province (DLIP). Mineralogically, these dykes show affinity towards alkaline (sannaite and camptonite) as well as ultramafic (damtjernite) varieties of lamprophyres. Their major oxides and certain trace element ratios increase with increasing silica content highlighting the strong influence of fractionation processes. Their Nb/U and Ce/Pb ratios are similar to the mantle array defined by MORBs and OIBs and suggests an uncontaminated nature. Major oxide (K〈sub〉2〈/sub〉O, Na〈sub〉2〈/sub〉O, SiO〈sub〉2〈/sub〉 and TiO〈sub〉2〈/sub〉) contents show geochemical similarity towards shoshonitic volcanic series, whereas elevated Zr/Hf and Nb/La coupled with suppressed Rb/Nb and Zr/b display their affinity towards HIMU-type intraplate basalts. Their radiogenic initial 〈sup〉87〈/sup〉Sr/〈sup〉86〈/sup〉Sr (0.706034–0.710582) and sub-chondritic initial ɛNd (−8.6 to 2.1) are akin to those of the (i) ca. 65 Ma Ambadongar carbonatite, NW India, and (ii) ca. 65 Ma orangeites from Bastar Craton, central India, highlighting an enriched lithospheric mantle source. REE inversion modeling suggests ~3% enrichment of an undepleted mantle followed by small degrees of melting of this enriched mantle source are sufficient- as in the case of ocean island basalts (OIB)- to reproduce their observed REE concentrations. Their T〈sub〉DM〈/sub〉 Nd model ages (564–961 Ma) are consistent with widespread convergent margin-related magmatism during the amalgamation of the Rodinia supercontinent. We propose that enriched lithospheric mantle developed during the Neoproterozoic was metasomatized by small-volume CO〈sub〉2〈/sub〉-rich melts imparting a HIMU-type geochemical character during Late Cretaceous, when the mantle plume (viz., Réunion) responsible for the flood basalt eruption, impinged at the base of the NW Indian lithosphere. From the presence of F-rich apatite and high K/Rb in mica, we infer the (i) presence of F-phlogopite in their source regions, and (ii) that the depth of post-Deccan lithosphere-asthenosphere boundary (LAB) beneath NW India was at least ~100 km at ca. 65 Ma.〈/p〉〈/div〉 〈/div〉

Description: 〈p〉Publication date: 15 December 2019〈/p〉 〈p〉〈b〉Source:〈/b〉 Lithos, Volumes 346–347〈/p〉 〈p〉Author(s): Babita Rani Choudhary, M. Santosh, Benedetto De Vivo, Gajananrao Jadhav, E.V.S.S.K. Babu〈/p〉 〈div xml:lang="en"〉 〈h5〉Abstract〈/h5〉 〈div〉〈p〉Silicate melt inclusions (MI) trapped in minerals provide direct tools to evaluate source characteristics and magma evolution including magma chamber processes. Here we present results from the study of MIs in basalts from the Western Ghats region of the Deccan Large Igneous Province (LIP) in India. The MIs in plagioclase and clinopyroxene phenocrysts were analyzed. The MIs exhibit post-entrapment modification by in situ crystal fractionation, chemical interaction with the host phenocryst (plagioclase or clinopyroxene), degassing/decrepitation, and crystallization of daughter minerals during cooling. The MIs display variable silica (SiO〈sub〉2〈/sub〉 41–68 wt%), low potassium, and high Fe〈img src="https://sdfestaticassets-eu-west-1.sciencedirectassets.com/shared-assets/16/entities/sbnd"〉Ti contents, corresponding to differentiation of basaltic to andesitic magma. Our data indicate H〈sub〉2〈/sub〉O content of about 2 wt% which is consistent with recent evidence for elevated primary H〈sub〉2〈/sub〉O content in the Deccan and other LIPs, corresponding to elevated H〈sub〉2〈/sub〉O in the lithospheric mantle and plumes passing through the mid-mantle inheriting the hydrous nature.〈/p〉〈/div〉 〈/div〉

Description: 〈p〉Publication date: 1 October 2019〈/p〉 〈p〉〈b〉Source:〈/b〉 Journal of Crystal Growth, Volume 523〈/p〉 〈p〉Author(s): Yuichiro Hayashi, Takeshi Mitani, Naoyoshi Komatsu, Tomohisa Kato, Hajime Okumura〈/p〉 〈div xml:lang="en"〉 〈h5〉Abstract〈/h5〉 〈div〉〈p〉We investigated the surface roughening in 4H-SiC solution growth from the following two aspects: the roughening of the seed surface before seeding and the roughening caused by the adhesion of SiC particles during growth. First, we investigated the morphological changes of the seed surface before and after the melt-back process. The seed surface just before seeding was covered with macrosteps and 6H-SiC hillocks with a height of several micrometers. This surface roughening was caused by condensation of droplets of vaporized solvent on the seed surface. We found that the 6H-SiC hillocks were the origins of trench defects. The melt-back process completely removed the hillocks and produced a smooth surface adequate for successive bulk growth. Second, we investigated surface roughening caused by the formation of SiC particles. The adhesion of SiC particles on the growth surface introduced trench defects and polytype inclusions. The adhesion of SiC particles was suppressed by controlling the distribution of carbon supersaturation in the solvent.〈/p〉〈/div〉 〈/div〉

Description: 〈p〉Publication date: 15 December 2019〈/p〉 〈p〉〈b〉Source:〈/b〉 Lithos, Volumes 346–347〈/p〉 〈p〉Author(s): Rosana Silveira Resende, Carlos Alberto Tello Sáenz, Luiz Augusto Stuani Pereira, Elton Luiz Dantas〈/p〉 〈div xml:lang="en"〉 〈h5〉Abstract〈/h5〉 〈div〉〈p〉Understanding the chemical etching effects in the crystalline structure of zircon grains is crucial to know their chemical composition, morphology and isotopic geochemistry. After chemical etching, the zircon grain can be classified as homogeneous heterogeneous, hybrid and anomalous depending on the surface fission-track density observed under an optical microscope. The complementary techniques such as optical microscopy, micro-Raman spectroscopy, scanning electron microscopy (imaging by cathodoluminescence and secondary electrons) and electron microprobe, were employed to characterize the zircon grain surfaces from Igneous, Metamorphic and Sedimentary rocks before and after chemical etching, except for Raman spectroscopy. Measurements of U-Pb age are concordant in areas on the grain surface with uniform fission-track density. The chemical and isotopic analyses show that the etching is capable of revealing the different layer imperfections of the zircon crystalline structure, which can be inherent in its crystallization or acquired during its geological history. Therefore, identification of crystallographic preserved areas on the zircon surface, which are associated with uniform fission-track density, helps to get highly concordant U-Pb ages. In general, the results showed that the U-Pb system depends significantly on the amorphization degree of the zircon crystalline structure, which in most cases can only be revealed by etching.〈/p〉〈/div〉 〈/div〉

Description: 〈p〉Publication date: October 2019〈/p〉 〈p〉〈b〉Source:〈/b〉 Journal of Applied Geophysics, Volume 169〈/p〉 〈p〉Author(s): Rakoto Heritiana A., Rajaomahefasoa Riva, Razafiarisera Ralay, Razafindrakoto Boni〈/p〉 〈div xml:lang="en"〉 〈h5〉Abstract〈/h5〉 〈div〉 〈p〉Multiple electrical geophysical survey techniques were used to evaluate the flaky graphite reserves found along the east coast of Madagascar. Self-potential (SP) combined with induced polarization (IP) and electrical resistivity tomography (ERT) methods were applied and provide information about the graphite ore spatial distribution. Unlike conventional geophysical survey methods that use SP and electromagnetic (EM) methods for exploration of this type of metal, the addition of IP and ERT offers a geoelectrical map and section which indicate correlations with the graphite content.〈/p〉 〈p〉The obtained SP map enabled us to delineate the mineralized area whereas the geoelectrical sections obtained from ERT and IP provide additional information on the vertical extent of the mineral of interest, in this case flake-graphite. We overlaid the graphite content, as measured on samples, on the SP map in order to verify the effectiveness of the geophysical methodology. Good correlation between negative SP anomalies and positive indication of graphite content confirms that the methods used in this study (SP, ERT and IP) are sensitive for delineation of the mineralized zone and consequent evaluation of the ore reserve. Resistivity and chargeability obtained from the inversion of the ERT/IP data are low and high, respectively, within the saturated zone inside SP-anomalous zones.〈/p〉 〈p〉The principal ore body is located in the lateritic zone composed of clay-rich formations derived from the weathering of gneiss and migmatite rocks. Negative SP anomalies, along with low electrical resistivity and high chargeability values, are found mainly in areas where the graphitic content exceeds 5%.〈/p〉 〈/div〉 〈/div〉

Description: 〈p〉Publication date: Available online 7 July 2019〈/p〉 〈p〉〈b〉Source:〈/b〉 Experimental Cell Research〈/p〉 〈p〉Author(s): Rong Jiang, Yan Liao, Fuhuang Yang, Yusi Cheng, Xiaoniu Dai, Jie Chao〈/p〉 〈div xml:lang="en"〉 〈h5〉Abstract〈/h5〉 〈div〉〈p〉Endothelial-mesenchymal transition (EndoMT) is a key step during lung fibrosis. Studies have shown that bone marrow mesenchymal stem cells (BMSCs) may act as therapeutic candidates for lung fibrosis. However, the effects of BMSCs on EndoMT induced by SiO〈sub〉2〈/sub〉 have not been elucidated, and means to label and track grafted cells have been lacking. The current study explored whether BMSCs prevented pulmonary fibrosis by targeting EndoMT, as well as analyzed the distribution of BMSCs labeled with superparamagnetic iron oxide (SPIO) nanoparticles during treatment. TIE2-GFP mice, human umbilical vein endothelial cells (HUVECs), and BMSCs labeled with SPIO nanoparticles were used to explore the distributions and therapeutic effects of BMSCs in vivo and in vitro. We found that BMSCs reversed lung fibrosis by targeting EndoMT in vivo. Furthermore, we show that BMSCs labeled with SPIO nanoparticles could be used to track stem cells reliably in the lungs for 14 days. Conditioned medium from BMSCs attenuated the increased functional changes and reversed the SiO〈sub〉2〈/sub〉-induced upregulation of ER stress and autophagy markers irrespective of whether they were nanoparticle labeled or not. Our findings identify novel methods to track labeled BMSCs with therapeutic potential.〈/p〉〈/div〉 〈/div〉

Description: 〈p〉Publication date: August 2019〈/p〉 〈p〉〈b〉Source:〈/b〉 Biochimica et Biophysica Acta (BBA) - Gene Regulatory Mechanisms, Volume 1862, Issue 8〈/p〉 〈p〉Author(s): Ruifan Wu, Guanqun Guo, Zhen Bi, Youhua Liu, Yuanling Zhao, Nana Chen, Fengqin Wang, Yizhen Wang, Xinxia Wang〈/p〉 〈div xml:lang="en"〉 〈h5〉Abstract〈/h5〉 〈div〉〈p〉〈em〉N〈/em〉〈sup〉6〈/sup〉-methyladenosine (m〈sup〉6〈/sup〉A), the most abundant internal mRNA modification in eukaryotes, plays a vital role in regulating adipogenesis. However, its underlying mechanism remains largely unknown. Here, we reveal that deletion of m〈sup〉6〈/sup〉A demethylase FTO in porcine and mouse preadipocytes inhibits adipogenesis through JAK2-STAT3-C/EBPβ signaling. Mechanistically, FTO deficiency suppresses JAK2 expression and STAT3 phosphorylation, leading to attenuated transcription of C/EBPβ, which is essential for the early stage of adipocyte differentiation. Using dual-luciferase assay, we validate that knockdown of FTO reduces expression of JAK2 in an m〈sup〉6〈/sup〉A-dependent manner. Furthermore, we find that m〈sup〉6〈/sup〉A “reader” protein YTHDF2 directly targets m〈sup〉6〈/sup〉A-modified transcripts of JAK2 and accelerates mRNA decay, which results in decreased JAK2 expression and inactivated JAK2-STAT3-C/EBPβ signaling, thereby inhibiting adipogenesis. Collectively, our results provide a novel insight into the molecular mechanism of m〈sup〉6〈/sup〉A methylation in post-transcriptional regulation of JAK2-STAT3-C/EBPβ signaling axis and highlight the crucial role of m〈sup〉6〈/sup〉A modification and its modulators in adipogenesis.〈/p〉〈/div〉 〈/div〉

Description: 〈p〉Publication date: 1 August 2019〈/p〉 〈p〉〈b〉Source:〈/b〉 Biochimica et Biophysica Acta (BBA) - Biomembranes, Volume 1861, Issue 8〈/p〉 〈p〉Author(s): 〈/p〉

Description: 〈p〉Publication date: 1 October 2019〈/p〉 〈p〉〈b〉Source:〈/b〉 Biochimica et Biophysica Acta (BBA) - Molecular Basis of Disease, Volume 1865, Issue 10〈/p〉 〈p〉Author(s): Tomonaga Ichikawa, Shingo Nakahata, Masahiro Fujii, Hidekatsu Iha, Kazuya Shimoda, Kazuhiro Morishita〈/p〉 〈div xml:lang="en"〉 〈h5〉Abstract〈/h5〉 〈div〉〈p〉N-myc downstream-regulated gene 2 (NDRG2) is a candidate tumor suppressor that is frequently downregulated in adult T-cell leukemia/lymphoma (ATLL) and functions to negatively regulate several cellular signaling pathways as PP2A recruiter. To clarify the molecular mechanisms of suppression of NDRG2 expression, we initially determined the expression pattern of NDRG2 in various types of T-cells and ATLL cells. NDRG2 expression was significantly upregulated in HTLV-1/Tax-immortalized T-cells, which was mediated by NF-κB activation through Tax expression. On the other hand, NDRG2 expression was suppressed in HTLV-1-infected cell lines and various types of ATLL cells, which was dependent on the DNA methylation of the NDRG2 promoter. We found that the expression of enhancer of zeste homolog 2 (EZH2), a member of the polycomb family, is increased in ATLL, and that EZH2 directly binds to the NDRG2 promoter and induces DNA methylation of the NDRG2 promoter. Since the expression of EZH2 were anti-parallelly regulated with the NDRG2 expression, EZH2 might be one of the most important regulators of the downregulation of NDRG2, contributing to enhanced activation of signaling pathways during ATLL development.〈/p〉〈/div〉 〈/div〉

Description: 〈p〉Publication date: 1 September 2019〈/p〉 〈p〉〈b〉Source:〈/b〉 Biochimica et Biophysica Acta (BBA) - Biomembranes, Volume 1861, Issue 9〈/p〉 〈p〉Author(s): Mariafrancesca Scalise, Michele Galluccio, Lorena Pochini, Jessica Cosco, Miriam Trotta, Manuele Rebsamen, Giulio Superti-Furga, Cesare Indiveri〈/p〉 〈div xml:lang="en"〉 〈h5〉Abstract〈/h5〉 〈div〉〈p〉The lysosomal amino acid transporter SLC38A9 is referred to as transceptor, i.e. a transporter with a receptor function. The protein is responsible for coupling amino acid transport across the lysosomal membrane according to the substrate availability to mTORC1 signal transduction. This process allows cells to sense amino acid level responding to growth stimuli in physiological and pathological conditions triggering mTOR regulation. The main substrates underlying this function are glutamine and arginine. The functional and kinetic characterization of glutamine and arginine transport was performed using human SLC38A9 produced in 〈em〉E. coli〈/em〉, purified by affinity chromatography and reconstituted in liposomes. A cooperative behaviour for the wild type protein was revealed for both the substrates. A novel Na〈sup〉+〈/sup〉 binding site, namely T453, was described by combined approaches of bioinformatics, site-directed mutagenesis and transport assay. Stimulation by cholesterol of glutamine and arginine transport was observed. The biological function of SLC38A9 relies on the interaction between its N-terminus and components of the mTOR complex; a deletion mutant of the N-terminus tail was produced and transport of glutamine was assayed revealing that this portion does not play any role in the intrinsic transport function of the human SLC38A9. Different features for glutamine and arginine transport were revealed: human SLC38A9 is competent for glutamine efflux, while that of arginine is negligible. In line with these results, imposed ∆pH stimulated glutamine, not arginine transport. Arginine plays, on the contrary, a modulatory function and is able to stimulate glutamine efflux. Interestingly, reciprocal inhibition experiments also supported by bioinformatics, suggested that glutamine and arginine may bind to different sites in the human SLC38A9 transporter.〈/p〉〈/div〉 〈/div〉 〈div xml:lang="en"〉 〈h5〉Graphical abstract〈/h5〉 〈div〉〈p〉Proteoliposome reconstitution of hSLC38A9 WT and mutants.〈figure〉〈img src="https://ars.els-cdn.com/content/image/1-s2.0-S0005273619301567-ga1.jpg" width="301" alt="Unlabelled Image" title="Unlabelled Image"〉〈/figure〉〈/p〉〈/div〉 〈/div〉

Description: 〈p〉Publication date: Available online 8 July 2019〈/p〉 〈p〉〈b〉Source:〈/b〉 Computer Methods and Programs in Biomedicine〈/p〉 〈p〉Author(s): Alae Ammour, Ibtissame Aouraghe, Ghizlane Khaissidi, Mostapha Mrabti, Ghita Aboulem, Faouzi Belhacen〈/p〉 〈h5〉Abstract〈/h5〉 〈div〉〈p〉Parkinson's disease (PD) is the second most common neurodegenerative disease affecting significant portion of elderly population. One of the most frequent hallmarks and the first manifestation of PD is deterioration of handwriting. Since the diagnosis of Parkinson's disease is difficult, researchers have worked to develop a support tool based on algorithms to separate healthy controls from PD patients. On-line handwriting analysis is one of the methods that can be used to diagnose PD. In this study, we aimed to analyze the Arabic Handwriting of 28 Parkinson's disease patients and 28 healthy controls (HCs) who were the same age and have the same intellectual level. We focused on copying an Arabic text task. For each participant we have calculated 1482 features. Based on the most relevant features selected by the Pearson's coefficient correlation, the Hierarchical Ascendant Classification (HAC) was applied and generated 3 clusters of writers. The characterization of these clusters was carried out by using the quantitative and qualitative parameters. The obtained results show that the combination of these two aspects can discriminate at best PD patients from HCs.〈/p〉〈/div〉

Description: 〈p〉Publication date: September 2019〈/p〉 〈p〉〈b〉Source:〈/b〉 Biochimica et Biophysica Acta (BBA) - General Subjects, Volume 1863, Issue 9〈/p〉 〈p〉Author(s): 〈/p〉

Description: 〈p〉Publication date: 3 September 2019〈/p〉 〈p〉〈b〉Source:〈/b〉 Biochemical and Biophysical Research Communications, Volume 516, Issue 4〈/p〉 〈p〉Author(s): Shuangdong Chen, Yixiao Gu, Qinxue Dai, Yanshu He, Junlu Wang〈/p〉 〈div xml:lang="en"〉 〈h5〉Abstract〈/h5〉 〈div〉〈p〉Sirtuin1 (SIRT1), which is regulated by microRNA-34a (miR-34a), can modulate pathophysiology processes, including nonalcoholic fatty liver disease and intestinal ischemia/reperfusion injury. We previously reported that SIRT1, an NAD〈sup〉+〈/sup〉-dependent deacetylase, plays a vital role in the development of neuropathic pain. However, the role of miR-34a/SIRT1 in complete Freund's adjuvant (CFA)-induced inflammatory pain remains unclear. In the present study, we examined miR-34a and SIRT1 in CFA mice. MiR-34a levels increased, while SIRT1 decreased in the spinal cord. Inhibiting miR-34a by intrathecal injection of miR-34a antagomir attenuated CFA-induced pain behavior. Moreover, miR-34a antagomir inhibited the CFA-induced SIRT1 decrease in the spinal cord. Furthermore, the analgesic effect of miR-34a antagomir was abrogated by the SIRT1 inhibitor EX-527. Our data provide support that the underlying mechanisms of miR-34a in promoting inflammatory pain may involve negative regulation of SIRT1.〈/p〉〈/div〉 〈/div〉

Description: 〈p〉Publication date: 1 September 2019〈/p〉 〈p〉〈b〉Source:〈/b〉 Biochimica et Biophysica Acta (BBA) - Biomembranes, Volume 1861, Issue 9〈/p〉 〈p〉Author(s): Oumaima Et-Thakafy, Fanny Guyomarc'h, Christelle Lopez〈/p〉 〈div xml:lang="en"〉 〈h5〉Abstract〈/h5〉 〈div〉〈p〉The biological membrane surrounding milk fat globules (MFGM) exhibits lateral phase separation of lipids, interpreted as gel or liquid-ordered phase sphingomyelin-rich (milk SM) domains dispersed in a fluid continuous lipid phase. The objective of this study was to investigate whether changes in the phase state of milk SM-rich domains induced by temperature (T 〈 Tm or T 〉 Tm) or cholesterol affected the Young modulus of the lipid membrane. Supported lipid bilayers composed of MFGM polar lipids, milk SM or milk SM/cholesterol (50:50 mol) were investigated at 20 °C and 50 °C using atomic force microscopy (AFM) and force spectroscopy. At 20 °C, gel-phase SM-rich domains and the surrounding fluid phase of the MFGM polar lipids exhibited Young modulus values of 10–20 MPa and 4–6 MPa, respectively. Upon heating at 50 °C, the milk SM-rich domains in MFGM bilayers as well as pure milk SM bilayers melted, leading to the formation of a homogeneous membrane with similar Young modulus values to that of a fluid phase (0–5 MPa). Upon addition of cholesterol to the milk SM to reach 50:50 mol%, membranes in the liquid-ordered phase exhibited Young modulus values of a few MPa, at either 20 or 50 °C. This indicated that the presence of cholesterol fluidized milk SM membranes and that the Young modulus was weakly affected by the temperature. These results open perspectives for the development of milk polar lipid based vesicles with modulated mechanical properties.〈/p〉〈/div〉 〈/div〉 〈div xml:lang="en"〉 〈h5〉Graphical abstract〈/h5〉 〈div〉〈p〉〈figure〉〈img src="https://ars.els-cdn.com/content/image/1-s2.0-S0005273619301555-ga1.jpg" width="317" alt="Unlabelled Image" title="Unlabelled Image"〉〈/figure〉〈/p〉〈/div〉 〈/div〉

Description: 〈p〉Publication date: 1 October 2019〈/p〉 〈p〉〈b〉Source:〈/b〉 Water Research, Volume 162〈/p〉 〈p〉Author(s): Marine Diana, Mónica Felipe-Sotelo, Tom Bond〈/p〉 〈div xml:lang="en"〉 〈h5〉Abstract〈/h5〉 〈div〉〈p〉Epidemiological studies have consistently associated the consumption of chlorinated drinking water with an enhanced risk of bladder cancer. While this suggests that some disinfection byproducts (DBPs) are bladder carcinogens, causal agents are unknown. This study aims to highlight likely candidates. To achieve this, structures of known and hypothesised DBPs were compared with 76 known bladder carcinogens. The latter are dominated by nitrogenous and aromatic compounds; only 10 are halogenated. Under 10% of the chlorine applied during drinking water treatment is converted into identified halogenated byproducts; most of the chlorine is likely to be consumed during the generation of unidentified non-halogenated oxidation products. Six nitrosamines are among the nine most potent bladder carcinogens, and two of them are known to be DBPs: N-nitrosodiphenylamine and nitrosodibutylamine. However, these and other nitrosamines are formed in insufficiently low concentrations in chlorinated drinking water to account for the observed bladder cancer risk. Furthermore, although not proven bladder carcinogens, certain amines, haloamides, halocyclopentenoic acids, furans and haloquinones are potential candidates. At present, most identified bladder carcinogens are nitrogenous, whereas 〉90% of natural organic matter is not. Therefore, non-nitrogenous DBPs are likely to contribute to the bladder cancer risk. Given the high proportion of DBPs that remains uncharacterised, it is important that future research prioritises compounds believed to be potent toxicants.〈/p〉〈/div〉 〈/div〉 〈h5〉Graphical abstract〈/h5〉 〈div〉〈p〉〈figure〉〈img src="https://ars.els-cdn.com/content/image/1-s2.0-S004313541930613X-fx1.jpg" width="354" alt="Image 1" title="Image 1"〉〈/figure〉〈/p〉〈/div〉

Description: 〈p〉Publication date: October 2019〈/p〉 〈p〉〈b〉Source:〈/b〉 Solid State Communications, Volume 300〈/p〉 〈p〉Author(s): Jayeeta Chowdhury, Sachindra Nath Karmakar〈/p〉 〈div xml:lang="en"〉 〈h5〉Abstract〈/h5〉 〈div〉〈p〉In this paper we have introduced a new method based on real space renormalization group technique to find the density of states of three dimensional quasiperiodic lattices in the thermodynamic limit. The importance of this method lies in the fact that for three dimensional quasiperiodic lattices in this limit, no other technique is available in the literature for the density of states till now. Finding the density of states, we have also studied the electronic specific heat of such lattices and revealed the nature of temperature dependence of the specific heat.〈/p〉〈/div〉 〈/div〉

Description: 〈p〉Publication date: 16 August 2019〈/p〉 〈p〉〈b〉Source:〈/b〉 Tetrahedron, Volume 75, Issue 33〈/p〉 〈p〉Author(s): Mathilde Pantin, Florent Bodinier, Jordan Saillour, Yassine M. Youssouf, Fabien Boeda, Morwenna S.M. Pearson-Long, Philippe Bertus〈/p〉 〈div xml:lang="en"〉 〈h5〉Abstract〈/h5〉 〈div〉〈p〉A convenient access to 2-hydroxycyclopentenones was designed from acylcyanohydrins, by using titanacyclopropane complexes as nucleophilic partners and an intramolecular aldol condensation in basic conditions. The development of a one-pot procedure allows a step- and atom-economic process, and the use of Grignard reagents other than ethylmagnesium bromide provided valuable 3,4-disubstituted 2-hydroxycyclopentenones. The utility of the hydroxy group was illustrated by further functionalization of the α-position using palladium-mediated cross-coupling reactions.〈/p〉〈/div〉 〈/div〉 〈h5〉Graphical abstract〈/h5〉 〈div〉〈p〉〈figure〉〈img src="https://ars.els-cdn.com/content/image/1-s2.0-S0040402019307525-fx1.jpg" width="500" alt="Image 1" title="Image 1"〉〈/figure〉〈/p〉〈/div〉

Description: 〈p〉Publication date: 1 October 2019〈/p〉 〈p〉〈b〉Source:〈/b〉 Computer Methods in Applied Mechanics and Engineering, Volume 355〈/p〉 〈p〉Author(s): Jean-Lou Pfister, Olivier Marquet, Marco Carini〈/p〉 〈h5〉Abstract〈/h5〉 〈div〉〈p〉The stability analysis of elastic structures strongly coupled to incompressible viscous flows is investigated in this paper, based on a linearization of the governing equations formulated with the Arbitrary-Lagrangian–Eulerian method. The exact linearized formulation, previously derived to solve the unsteady non-linear equations with implicit temporal schemes, is used here to determine the physical linear stability of steady states. Once discretized with a standard finite-element method based on Lagrange elements, the leading eigenvalues/eigenmodes of the linearized operator are computed for three configurations representative for classical fluid–structure interaction instabilities: the vortex-induced vibrations of an elastic plate clamped to the rear of a rigid cylinder, the flutter instability of a flag immersed in a channel flow and the vortex shedding behind a three-dimensional plate bent by the steady flow. The results are in good agreement with instability thresholds reported in the literature and obtained with time-marching simulations, at a much lower computational cost. To further decrease this computational cost, the equations governing the solid perturbations are projected onto a reduced basis of free-vibration modes. This projection allows to eliminate the extension perturbation, a non-physical variable introduced in the ALE formalism to propagate the infinitesimal displacement of the fluid–solid interface into the fluid domain.〈/p〉〈/div〉

Description: 〈p〉Publication date: September 2019〈/p〉 〈p〉〈b〉Source:〈/b〉 Advances in Water Resources, Volume 131〈/p〉 〈p〉Author(s): Shaokun He, Shenglian Guo, Kebing Chen, Lele Deng, Zhen Liao, Feng Xiong, Jiabo Yin〈/p〉 〈h5〉Abstract〈/h5〉 〈div〉〈p〉The optimal impoundment operation of cascade reservoirs can dramatically improve the utilization of water resources. However, their complex non-convexity and computational costs pose challenges to optimal hydroelectricity output and limit further development of joint operation within larger-scale cascade reservoirs. In recent decades, parallel dynamic programming (PDP) has emerged as a means of alleviating the ‘curse of dimensionality’ in the mid-long term reservoir operation with more involved computing processors. But it still can't effectively solve the daily impoundment operation of more than three reservoirs. Here, we propose a novel method called importance sampling-PDP (IS-PDP) algorithm in which the merits of PDP are integrated with importance sampling and successive approximation strategy. Importance sampling is first used to construct the state vectors of each period by introducing ‘Manhattan distance’ in the discrete state space. Then the PDP recursive equation is used to find an improved solution during the iteration. The IS-PDP method is tested to optimize hydropower output for the joint operation of an 11-reservoir system located in the upper Yangtze River basin of China after establishing impoundment operation by advancing impoundment timings and rising water levels. We find that our methodology could effectively deal with the ‘curse of dimensionality’ for such mega reservoir systems and make better use of water resources in comparison to the Standard Operation Policy (SOP). Given its computational efficiency and robust convergence, the methodology is an attractive alternative for non-convex operation of large-scale cascade reservoirs.〈/p〉〈/div〉

Description: 〈p〉Publication date: November 2019〈/p〉 〈p〉〈b〉Source:〈/b〉 Ultramicroscopy, Volume 206〈/p〉 〈p〉Author(s): P. Kükelhan, T. Hepp, S. Firoozabadi, A. Beyer, K. Volz〈/p〉 〈h5〉Abstract〈/h5〉 〈div〉〈p〉Quantitative scanning transmission electron microscopy (STEM) is a powerful tool for the characterization of nano-materials. Absolute composition determination for ternary III–V semiconductors by direct comparison of experiment and simulation is well established. Here, we show a method to determine the composition of quaternary III–V semiconductors with two elements on each sub lattice from the intensities of one STEM image. As an example, this is applied to (GaIn)(AsBi). The feasibility of the method is shown in a simulation study that also explores the influence of detector angles and specimen thickness. Additionally, the method is applied to an experimental STEM image of a (GaIn)(AsBi) quantum well grown by metal organic vapour phase epitaxy. The obtained concentrations are in good agreement with X-ray diffraction and photoluminescence results.〈/p〉〈/div〉

Description: 〈p〉Publication date: July–August 2019〈/p〉 〈p〉〈b〉Source:〈/b〉 Materials Today, Volume 27〈/p〉 〈p〉Author(s): Laurie Donaldson〈/p〉

Description: 〈p〉Publication date: 1 November 2019〈/p〉 〈p〉〈b〉Source:〈/b〉 Materials Letters, Volume 254〈/p〉 〈p〉Author(s): Zhi-Hu Wang, Hong-Wei He, Guo-Sai Liu, Xu Yan, Xin Ning, Yun-Ze Long〈/p〉 〈div xml:lang="en"〉 〈h5〉Abstract〈/h5〉 〈div〉〈p〉In conventional electrospinning (e-spinning) process, the curing mechanism can be attributed to the volatilization of solvent or the melt cooling of the jets, which were merely physical processes. To develop novel e-spinning curing mechanism, we propose a conjugate e-spinning one, in which the e-spinning precursors, solution A containing some active monomers, oxidant and solution B containing reductant, are loaded into two different syringes connected with opposite high voltage supplier, respectively. The opposite charged jets attract each other and then meet when flying from spinneret tip to collector. The redox reaction occurs when two jets meet and radicals are produced in situ which can initiate polymerization of active monomers. Then the conjugate jets solidify into fibers under reaction curing mechanism. The new method may give a new approach to produce composite functional fibers.〈/p〉〈/div〉 〈/div〉 〈div xml:lang="en"〉 〈h5〉Graphical abstract〈/h5〉 〈div〉 〈p〉Two solutions containing oxidant and reductant, respectively are electrospun into fibers via a conjugate electrospinning process under a reaction curing mechanism.〈/p〉 〈p〉〈figure〉〈img src="https://ars.els-cdn.com/content/image/1-s2.0-S0167577X19309954-ga1.jpg" width="271" alt="Graphical abstract for this article" title=""〉〈/figure〉〈/p〉 〈/div〉 〈/div〉

Description: 〈p〉Publication date: 5 October 2019〈/p〉 〈p〉〈b〉Source:〈/b〉 Journal of Alloys and Compounds, Volume 804〈/p〉 〈p〉Author(s): J.Y. Oh, Tien M. Le, A.T. Pham, D.H. Tran, D.S. Yang, B. Kang〈/p〉 〈div xml:lang="en"〉 〈h5〉Abstract〈/h5〉 〈div〉〈p〉In this work, we investigated a correlation between superconductivity and interlayer coupling of two different alkaline (Na and K)-substituted Bi〈sub〉1·6〈/sub〉Pb〈sub〉0·4〈/sub〉Sr〈sub〉2〈/sub〉Ca〈sub〉2〈/sub〉Cu〈sub〉3〈/sub〉O〈sub〉10+δ〈/sub〉 (BSCCO) polycrystalline samples. The excess conductivity analysis by the Aslamazov-Larkin (AL) and Lawrence-Doniach (LD) theories showed that Na substitution at the Ca site induced a gradual broadening of 3D fluctuation region with increasing interlayer coupling strength, which explains a systematic increase of 〈em〉T〈/em〉〈sub〉〈em〉c〈/em〉〈/sub〉 and a decrease of normal state resistivity. On the other hand, exactly the opposite results were observed in the K-substituted samples in place of Sr. Extended x-ray absorption fine structure (EXAFS) studies revealed that substitution of Na and K generated completely different effects on the local structure around Cu atoms. It is noticeable that the Cu–O bond distance was found to decrease monotonically with the varying amounts of Na, which indicates that the CuO〈sub〉2〈/sub〉 layer is stabilized. On the while, the opposite was observed to occur with the varying amounts of K. Unlike the Cu–Ca bond which was the least affected by the substitution, the Cu–Sr bond distance increased drastically with K substitution. All these findings indicate that Na substitution at the Ca site enhances superconductivity with no loss of interlayer interaction, while K substitution at the Sr site weakens superconductivity due to the diminished interlayer interaction.〈/p〉〈/div〉 〈/div〉

Description: 〈p〉Publication date: 5 October 2019〈/p〉 〈p〉〈b〉Source:〈/b〉 Journal of Alloys and Compounds, Volume 804〈/p〉 〈p〉Author(s): Moara M. Castro, Shima Sabbaghianrad, Pedro Henrique R. Pereira, Eric M. Mazzer, Augusta Isaac, Terence G. Langdon, Roberto B. Figueiredo〈/p〉 〈div xml:lang="en"〉 〈h5〉Abstract〈/h5〉 〈div〉〈p〉A magnesium/aluminium composite was produced by room temperature consolidation through high-pressure torsion (HPT) processing. Half-discs of the pure metals were placed side-by-side and subjected to different numbers of turns. The initially reduced interface between the phases gradually increased with increasing rotation. The composite displayed a significant ductility even after 10 turns. The distribution of hardness in the HPT-processed discs was bi-modal in the early stages of processing. As the number of turns increased and the thickness of the phases decreased there was a noticeable increase in hardness. The hardness values of the composite further increased after thermal treatment due to the formation of intermetallics within the interface between the magnesium and aluminium-rich phases.〈/p〉〈/div〉 〈/div〉

Description: 〈p〉Publication date: 5 October 2019〈/p〉 〈p〉〈b〉Source:〈/b〉 Journal of Alloys and Compounds, Volume 804〈/p〉 〈p〉Author(s): Lipeng Xu, Fei Zhou, Jizhou Kong, Haobin Zhou, Qian Zhang〈/p〉 〈div xml:lang="en"〉 〈h5〉Abstract〈/h5〉 〈div〉〈p〉The effects of testing temperature on the electrochemical properties of Li(Ni〈sub〉0.6〈/sub〉Mn〈sub〉0.2〈/sub〉Co〈sub〉0.2〈/sub〉)O〈sub〉2〈/sub〉 are investigated in detail. When the testing temperature is 40 °C, the Li(Ni〈sub〉0.6〈/sub〉Mn〈sub〉0.2〈/sub〉Co〈sub〉0.2〈/sub〉)O〈sub〉2〈/sub〉 cathode material possesses the highest initial discharge capacity of 162.4 mAh·g〈sup〉−1〈/sup〉 at 0.5C rate, but their cycling stability decreases markedly. When the test temperature rises up to 60 °C, the side reaction between electrolyte and cathode material becomes serious, and the Li(Ni〈sub〉0.6〈/sub〉Mn〈sub〉0.2〈/sub〉Co〈sub〉0.2〈/sub〉)O〈sub〉2〈/sub〉 cannot work. When the testing temperature decreases, the electrochemical impedances like R〈sub〉ct〈/sub〉 values increase, and then the discharge capacity at 0 °C, −10 °C and −20 °C is only 80%, 53% and 23% of that at 25 °C. Based on the electrochemical impedance spectra at different temperatures, four kinds of equivalent circuit models are classified. The cycle and rate performance of Li(Ni〈sub〉0.6〈/sub〉Mn〈sub〉0.2〈/sub〉Co〈sub〉0.2〈/sub〉)O〈sub〉2〈/sub〉 cathode material could be improved obviously through Ti〈sub〉3〈/sub〉C〈sub〉2〈/sub〉(OH)〈sub〉2〈/sub〉 modification in an extreme environment, and especially in sub-zero environment.〈/p〉〈/div〉 〈/div〉

Description: 〈p〉Publication date: November 2019〈/p〉 〈p〉〈b〉Source:〈/b〉 Journal of Materials Processing Technology, Volume 273〈/p〉 〈p〉Author(s): 〈/p〉

Description: 〈p〉Publication date: 5 October 2019〈/p〉 〈p〉〈b〉Source:〈/b〉 Journal of Alloys and Compounds, Volume 804〈/p〉 〈p〉Author(s): Kenji Yoshii, Naoshi Ikeda〈/p〉 〈div xml:lang="en"〉 〈h5〉Abstract〈/h5〉 〈div〉〈p〉Dielectric and magnetocaloric measurements are carried out for the chromite TmCrO〈sub〉3〈/sub〉. This oxide was reported to be multiferroic below the Néel temperature (〈em〉T〈/em〉〈sub〉N〈/sub〉) of ∼125 K, likely due to a structural transformation. The dielectric response shows large dielectric constants below 300 K. However, from the analyses of loss tangent, AC conductivity and dielectric modulus, this behavior is rooted in hopping of charge carriers rather than electric dipoles, as proposed for some other chromites. No dielectric anomaly is found at 〈em〉T〈/em〉〈sub〉N〈/sub〉. The magnetocaloric effect shows that the magnetic transitions at 〈em〉T〈/em〉〈sub〉N〈/sub〉 as well as the spin reorientation temperature are of a second order. This result strongly suggests the absence of magnetostructural transition at 〈em〉T〈/em〉〈sub〉N〈/sub〉 in accord with no observation of ferroelectric transition at this temperature.〈/p〉〈/div〉 〈/div〉

Description: 〈p〉Publication date: 5 October 2019〈/p〉 〈p〉〈b〉Source:〈/b〉 Journal of Alloys and Compounds, Volume 804〈/p〉 〈p〉Author(s): Rattiya Hongtong, Panya Thanwisai, Rattakarn Yensano, Jeffrey Nash, Sutham Srilomsak, Nonglak Meethong〈/p〉 〈div xml:lang="en"〉 〈h5〉Abstract〈/h5〉 〈div〉〈p〉Core-shell olivine-type electrospun and doped LiFePO〈sub〉4〈/sub〉/FeS/C composite fibers were synthesized via a single-step process employing an electrospinning method using LiOH·H〈sub〉2〈/sub〉O, metal sul phates, H〈sub〉3〈/sub〉PO〈sub〉4〈/sub〉, citric acid, and polyvinylpyrrolidone (PVP) as the starting materials. Electron microscopy studies showed that the mean diameter of the core-shell composite fibers was about 280 ± 20 nm with a LiFePO〈sub〉4〈/sub〉 phase forming a core with a diameter of about 100 ± 20 nm and a carbon shell with a thickness of 80 ± 20 nm. An FeS phase was formed by a direct reduction of iron (II) sulfate (FeSO〈sub〉4〈/sub〉) that was evenly distributed within the core region of the composite fibers and further improved the electronic conductivity of the fibers. Na〈sup〉1+〈/sup〉, Mg〈sup〉2+〈/sup〉, and Al〈sup〉3+〈/sup〉 doping ions affected fiber morphology and electrochemical performance. All composite fibers showed excellent electrochemical performance. However, Al〈sup〉3+〈/sup〉 ions improved the electrochemical performance of the composite fibers to a significantly greater degree than Na〈sup〉1+〈/sup〉 and Mg〈sup〉2+〈/sup〉 doping ions, increasing the electronic and ionic conductivities of the material while maintaining their core-shell composite fiber characteristics.〈/p〉〈/div〉 〈/div〉 〈h5〉Graphical abstract〈/h5〉 〈div〉〈p〉Electrospun LiFePO〈sub〉4〈/sub〉/FeS/C and 5% doped 〈math xmlns:mml="http://www.w3.org/1998/Math/MathML" altimg="si1.svg"〉〈mrow〉〈mi〉L〈/mi〉〈mi〉i〈/mi〉〈mi〉F〈/mi〉〈msubsup〉〈mrow〉〈mi〉e〈/mi〉〈/mrow〉〈mrow〉〈mn〉1〈/mn〉〈mo linebreak="badbreak"〉−〈/mo〉〈mrow〉〈mo stretchy="false"〉(〈/mo〉〈mi〉n〈/mi〉〈mi〉x〈/mi〉〈mo linebreak="badbreak"〉/〈/mo〉〈mn〉2〈/mn〉〈mo stretchy="false"〉)〈/mo〉〈/mrow〉〈/mrow〉〈mrow〉〈mn〉2〈/mn〉〈mo linebreak="badbreak"〉+〈/mo〉〈/mrow〉〈/msubsup〉〈msubsup〉〈mrow〉〈mi〉M〈/mi〉〈/mrow〉〈mrow〉〈mi〉x〈/mi〉〈/mrow〉〈mrow〉〈mi〉n〈/mi〉〈mo linebreak="badbreak"〉+〈/mo〉〈/mrow〉〈/msubsup〉〈mi〉P〈/mi〉〈msub〉〈mrow〉〈mi〉O〈/mi〉〈/mrow〉〈mrow〉〈mn〉4〈/mn〉〈/mrow〉〈/msub〉〈/mrow〉〈/math〉/FeS/C (M = Na〈sup〉1+〈/sup〉, Mg〈sup〉2+〈/sup〉, Al〈sup〉3+〈/sup〉) composites with a unique core-shell structure were synthesized via a simple single-step process to improved electrochemical properties for high performance and low cost Li-ion batteries.〈figure〉〈img src="https://ars.els-cdn.com/content/image/1-s2.0-S0925838819324946-fx1.jpg" width="287" alt="Image 1" title="Image 1"〉〈/figure〉〈/p〉〈/div〉

Description: 〈p〉Publication date: 5 October 2019〈/p〉 〈p〉〈b〉Source:〈/b〉 Journal of Alloys and Compounds, Volume 804〈/p〉 〈p〉Author(s): L.V.B. Diop, O. Isnard〈/p〉 〈div xml:lang="en"〉 〈h5〉Abstract〈/h5〉 〈div〉〈p〉The effects of Fe substitution on the structural and magnetic properties of the HoCo〈sub〉12-〈em〉x〈/em〉〈/sub〉Fe〈sub〉〈em〉x〈/em〉〈/sub〉B〈sub〉6〈/sub〉 (0 ≤ 〈em〉x〈/em〉 ≤ 2) series of intermetallic compounds have been studied. All of the compounds form in the rhombohedral SrNi〈sub〉12〈/sub〉B〈sub〉6〈/sub〉-type structure, the lattice constants increasing linearly with 〈em〉x〈/em〉. These compounds are ferrimagnets with a small transition metal magnetic moment and exhibit a spin reorientation transition. The Curie temperature decreases from 147 K for 〈em〉x〈/em〉 = 0–105 K for 〈em〉x〈/em〉 = 2. The Fe for Co substitution leads also to a progressive decrease of the spontaneous magnetization. The spin reorientation transition temperature is significantly reduced upon Fe for Co substitution whereas the compensation temperature is much less sensitive to the Fe composition.〈/p〉〈/div〉 〈/div〉