ALBERT

Description: Remote Sensing, Vol. 10, Pages 1182: Detection of Frozen Soil Using Sentinel-1 SAR Data Remote Sensing doi: 10.3390/rs10081182 Authors: Nicolas Baghdadi Hassan Bazzi Mohammad El Hajj Mehrez Zribi The objective of this paper is to evaluate the potential of Sentinel-1 Synthetic Aperture Radar “SAR” data (C-band) for monitoring agricultural frozen soils. First, investigations were conducted from simulated radar signal data using a SAR backscattering model combined with a dielectric mixing model. Then, Sentinel-1 images acquired at a study site near Paris, France were analyzed using temperature data to investigate the potential of the new Sentinel-1 SAR sensor for frozen soil mapping. The results show that the SAR backscattering coefficient decreases when the soil temperature drops below 0 °C. This decrease in signal is the most important for temperatures that ranges between 0 and −5 °C. A difference of at least 2 dB is observed between unfrozen soils and frozen soils. This difference increases under freezing condition when the temperature at the image acquisition date decreases. In addition, results show that the potential of the C-band radar signal for the discrimination of frozen soils slightly decreases when the soil moisture decreases (simulated data were used with soil moisture contents of 20 and 30 vol%). The difference between the backscattering coefficient of unfrozen soil and the backscattering coefficient of frozen soil decreases by approximately 1 dB when the soil moisture decreases from 30 to 20 vol%). Finally, the results show that both VV and VH allow a good detection of frozen soils but the sensitivity of VH is higher by approximately 1.5 dB. In conclusion, this study shows that the difference between a reference image acquired without freezing and an image acquired under freezing conditions is a good tool for detecting frozen soils.

Description: Sensors, Vol. 18, Pages 2436: Bio-Inspired Covert Active Sonar Strategy Sensors doi: 10.3390/s18082436 Authors: Jiajia Jiang Xianquan Wang Fajie Duan Chunyue Li Xiao Fu Tingting Huang Lingran Bu Ling Ma Zhongbo Sun The covertness of the active sonar is a very important issue and the sonar signal waveform design problem was studied to improve covertness of the system. Many marine mammals produce call pulses for communication and echolocation, and existing interception systems normally classify these biological signals as ocean noise and filter them out. Based on this, a bio-inspired covert active sonar strategy was proposed. The true, rather than man-made sperm whale, call pulses were used to serve as sonar waveforms so as to ensure the camouflage ability of sonar waveforms. A range and velocity measurement combination (RVMC) was designed by using two true sperm whale call pulses which had excellent range resolution (RR) and large Doppler tolerance (DT). The range and velocity estimation methods were developed based on the RVMC. In the sonar receiver, the correlation technology was used to confirm the start and end time of sonar signals and their echoes, and then based on the developed range and velocity estimation method, the range and velocity of the underwater target were obtained. Then, the RVMC was embedded into the true sperm whale call-train to improve the camouflage ability of the sonar signal-train. Finally, experiment results were provided to verify the performance of the proposed method.

Description: Sensors, Vol. 18, Pages 2435: Quantitative Contact-Less Estimation of Energy Expenditure from Video and 3D Imagery Sensors doi: 10.3390/s18082435 Authors: Gregor Koporec Goran Vučković Radoje Milić Janez Perš Measurement of energy expenditure is an important tool in sport science and medicine, especially when trying to estimate the extent and intensity of physical activity. However, most approaches still rely on sensors or markers, placed directly on the body. In this paper, we present a novel approach using a fully contact-less, fully automatic method, that relies on computer vision algorithms and widely available and inexpensive imaging sensors. We rely on the estimation of the optical and scene flow to calculate Histograms of Oriented Optical Flow (HOOF) descriptors, which we subsequently augment with the Histograms of Absolute Flow Amplitude (HAFA). Descriptors are fed into regression model, which allows us to estimate energy consumption, and to a lesser extent, the heart rate. Our method has been tested both in lab environment and in realistic conditions of a sport match. Results confirm that these energy expenditures could be derived from purely contact-less observations. The proposed method can be used with different modalities, including near infrared imagery, which extends its future potential.

Description: Sensors, Vol. 18, Pages 2434: Smart Portable Devices Suitable for Cultural Heritage: A Review Sensors doi: 10.3390/s18082434 Authors: Federica Valentini Andrea Calcaterra Simonetta Antonaroli Maurizio Talamo This article reviews recent portable sensor technologies to apply in the Cultural Heritage (CH) fields. The review has been prepared in the form of a retrospective description of the sensor’s history and technological evolution, having: new nanomaterials for transducers, miniaturized, portable and integrated sensors, the wireless transmission of the analytical signals, ICT_Information Communication Technology and IoT_Internet of Things to apply to the cultural heritage field. In addition, a new trend of movable tattoo sensors devices is discussed, referred to in situ analysis, which is especially important when scientists are in the presence of un-movable and un-tangible Cultural Heritage and Art Work objects. The new proposed portable contact sensors (directly applied to art work objects and surfaces) are non-invasive and non-destructive to the different materials and surfaces of which cultural heritage is composed.

Description: Sensors, Vol. 18, Pages 2433: Multi-Camera Imaging System for UAV Photogrammetry Sensors doi: 10.3390/s18082433 Authors: Damian Wierzbicki In the last few years, it has been possible to observe a considerable increase in the use of unmanned aerial vehicles (UAV) equipped with compact digital cameras for environment mapping. The next stage in the development of photogrammetry from low altitudes was the development of the imagery data from UAV oblique images. Imagery data was obtained from side-facing directions. As in professional photogrammetric systems, it is possible to record footprints of tree crowns and other forms of the natural environment. The use of a multi-camera system will significantly reduce one of the main UAV photogrammetry limitations (especially in the case of multirotor UAV) which is a reduction of the ground coverage area, while increasing the number of images, increasing the number of flight lines, and reducing the surface imaged during one flight. The approach proposed in this paper is based on using several head cameras to enhance the imaging geometry during one flight of UAV for mapping. As part of the research work, a multi-camera system consisting of several cameras was designed to increase the total Field of View (FOV). Thanks to this, it will be possible to increase the ground coverage area and to acquire image data effectively. The acquired images will be mosaicked in order to limit the total number of images for the mapped area. As part of the research, a set of cameras was calibrated to determine the interior orientation parameters (IOPs). Next, the method of image alignment using the feature image matching algorithms was presented. In the proposed approach, the images are combined in such a way that the final image has a joint centre of projections of component images. The experimental results showed that the proposed solution was reliable and accurate for the mapping purpose. The paper also presents the effectiveness of existing transformation models for images with a large coverage subjected to initial geometric correction due to the influence of distortion.

Description: Sensors, Vol. 18, Pages 2432: A Terahertz CMOS V-Shaped Patch Antenna with Defected Ground Structure Sensors doi: 10.3390/s18082432 Authors: Hyeongjin Kim Wonseok Choe Jinho Jeong In this paper, a V-shaped patch antenna with defected ground structure is proposed at terahertz to overcome the limited performance of a standard complementary metal-oxide semiconductor (CMOS) patch antenna consisting of several metal layers and very thin interdielectric layers. The proposed V-shaped patch with slots allows the increased radiation resistance and broadband performance. In addition, the patch resonating at different frequency from the V-shaped patch is stacked on the top to broaden the impedance-matching bandwidth. More importantly, the slots are formed in the ground plane, which is called the defected ground structure, to further increase the radiation resistance and thus improve the bandwidth and efficiency. It is verified from electromagnetic simulations that the leakage waves from the defected ground can enhance the antenna directivity and gain by coherently interfering with the topside radiation. The proposed on-chip antenna is fabricated using a standard 65 nm CMOS process. The on-wafer measurement shows very wide bandwidth in input reflection coefficient (<−10 dB), greater than 28.7% from 240 to >320 GHz. The measured peak gain was as high as 5.48 dBi at 295 GHz. To the best of the authors’ knowledge, these results belong to the best performance among the terahertz CMOS on-chip antennas without using additional components or processes such as dielectric resonators, lens, or substrate thinning.

Description: Sensors, Vol. 18, Pages 2430: Relative Pose Based Redundancy Removal: Collaborative RGB-D Data Transmission in Mobile Visual Sensor Networks Sensors doi: 10.3390/s18082430 Authors: Xiaoqin Wang Y. Ahmet Şekercioğlu Tom Drummond Vincent Frémont Enrico Natalizio Isabelle Fantoni In this paper, the Relative Pose based Redundancy Removal (RPRR) scheme is presented, which has been designed for mobile RGB-D sensor networks operating under bandwidth-constrained operational scenarios. The scheme considers a multiview scenario in which pairs of sensors observe the same scene from different viewpoints, and detect the redundant visual and depth information to prevent their transmission leading to a significant improvement in wireless channel usage efficiency and power savings. We envisage applications in which the environment is static, and rapid 3D mapping of an enclosed area of interest is required, such as disaster recovery and support operations after earthquakes or industrial accidents. Experimental results show that wireless channel utilization is improved by 250% and battery consumption is halved when the RPRR scheme is used instead of sending the sensor images independently.

Description: Sensors, Vol. 18, Pages 2439: HemoKinect: A Microsoft Kinect V2 Based Exergaming Software to Supervise Physical Exercise of Patients with Hemophilia Sensors doi: 10.3390/s18082439 Authors: Fernando Mateo Emilio Soria-Olivas Juan Carrasco Santiago Bonanad Felipe Querol Sofía Pérez-Alenda Patients with hemophilia need to strictly follow exercise routines to minimize their risk of suffering bleeding in joints, known as hemarthrosis. This paper introduces and validates a new exergaming software tool called HemoKinect that intends to keep track of exercises using Microsoft Kinect V2’s body tracking capabilities. The software has been developed in C++ and MATLAB. The Kinect SDK V2.0 libraries have been used to obtain 3D joint positions from the Kinect color and depth sensors. Performing angle calculations and center-of-mass (COM) estimations using these joint positions, HemoKinect can evaluate the following exercises: elbow flexion/extension, knee flexion/extension (squat), step climb (ankle exercise) and multi-directional balance based on COM. The software generates reports and progress graphs and is able to directly send the results to the physician via email. Exercises have been validated with 10 controls and eight patients. HemoKinect successfully registered elbow and knee exercises, while displaying real-time joint angle measurements. Additionally, steps were successfully counted in up to 78% of the cases. Regarding balance, differences were found in the scores according to the difficulty level and direction. HemoKinect supposes a significant leap forward in terms of exergaming applicability to rehabilitation of patients with hemophilia, allowing remote supervision.

Description: Sensors, Vol. 18, Pages 2428: Narrowband Characterization of Near-Ground Radio Channel for Wireless Sensors Networks at 5G-IoT Bands Sensors doi: 10.3390/s18082428 Authors: Hicham Klaina Ana Vazquez Alejos Otman Aghzout Francisco Falcone In this contribution, a narrowband radio channel model is proposed for rural scenarios in which the radio link operates under near-ground conditions for application in wireless sensor networks dedicated to smart agriculture. The received power attenuation was measured for both transmitter and receiver antennas placed at two different heights above ground: 0.2 and 0.4 m. Three frequency ranges, proposed for future 5G-IoT use case in agriculture, were chosen: 868 MHz, 2.4 GHz and 5.8 GHz. Three ground coverings were tested in a rural scenario: soil, short and tall grass fields. The path loss was then estimated as dependent of the radio link range and a three-slope log-normal path loss model was tailored. Results are explained in terms of the first Fresnel zone obstruction. Commercial Zigbee sensor nodes operating at 2.4 GHz were used in a second experiment to estimate the link quality from the experimental Radio Signal Strength Indicator (RSSI) received values. Two sensor nodes were placed at the same elevation above ground as in the previous experiment, only for short grass field case. The Quality of Service performance was determined in terms of theoretical bit error rate achieved for different digital modulations—BPSK, 8PSK and 16QAM—concluding remarkable results for an obstructed radio link.

Description: Sensors, Vol. 18, Pages 2429: A PUF- and Biometric-Based Lightweight Hardware Solution to Increase Security at Sensor Nodes Sensors doi: 10.3390/s18082429 Authors: Rosario Arjona Miguel Ángel Prada-Delgado Javier Arcenegui Iluminada Baturone Security is essential in sensor nodes which acquire and transmit sensitive data. However, the constraints of processing, memory and power consumption are very high in these nodes. Cryptographic algorithms based on symmetric key are very suitable for them. The drawback is that secure storage of secret keys is required. In this work, a low-cost solution is presented to obfuscate secret keys with Physically Unclonable Functions (PUFs), which exploit the hardware identity of the node. In addition, a lightweight fingerprint recognition solution is proposed, which can be implemented in low-cost sensor nodes. Since biometric data of individuals are sensitive, they are also obfuscated with PUFs. Both solutions allow authenticating the origin of the sensed data with a proposed dual-factor authentication protocol. One factor is the unique physical identity of the trusted sensor node that measures them. The other factor is the physical presence of the legitimate individual in charge of authorizing their transmission. Experimental results are included to prove how the proposed PUF-based solution can be implemented with the SRAMs of commercial Bluetooth Low Energy (BLE) chips which belong to the communication module of the sensor node. Implementation results show how the proposed fingerprint recognition based on the novel texture-based feature named QFingerMap16 (QFM) can be implemented fully inside a low-cost sensor node. Robustness, security and privacy issues at the proposed sensor nodes are discussed and analyzed with experimental results from PUFs and fingerprints taken from public and standard databases.

Description: Sustainability, Vol. 10, Pages 2633: Scenario-Based Simulation of Tianjin City Using a Cellular Automata–Markov Model Sustainability doi: 10.3390/su10082633 Authors: Ruci Wang Hao Hou Yuji Murayama Rapid urbanization is occurring throughout China, especially in megacities. Using a land use model to obtain future land use/cover conditions is an essential method to prevent chaotic urban sprawl and imbalanced development. This study utilized historical Landsat images to create land use/cover maps to predict the land use/cover changes of Tianjin city in 2025 and 2035. The cellular automata–Markov (CA–Markov) model was applied in the simulation under three scenarios: the environmental protection scenario (EPS), crop protection scenario (CPS), and spontaneous scenario (SS). The model achieved a kappa value of 86.6% with a figure of merit (FoM) of 12.18% when compared to the empirical land use/cover map in 2015. The results showed that the occupation of built-up areas increased from 29.13% in 2015 to 38.68% (EPS), 36.18% (CPS), and 47.94% (SS) in 2035. In this context, current urbanization would bring unprecedented stress on agricultural resources and forest ecosystems, which could be attenuated by implementing protection policies along with decelerating urban expansion. The findings provide valuable information for urban planners to achieve sustainable development goals.

Description: Sustainability, Vol. 10, Pages 2629: Pathways to Coastal Resiliency: The Adaptive Gradients Framework Sustainability doi: 10.3390/su10082629 Authors: Elisabeth M. Hamin Yaser Abunnasr Max Roman Dilthey Pamela K. Judge Melissa A. Kenney Paul Kirshen Thomas C. Sheahan Don J. DeGroot Robert L. Ryan Brain G. McAdoo Leonard Nurse Jane A. Buxton Ariana E. Sutton-Grier Elizabeth A. Albright Marielos Arlen Marin Rebecca Fricke Current and future climate-related coastal impacts such as catastrophic and repetitive flooding, hurricane intensity, and sea level rise necessitate a new approach to developing and managing coastal infrastructure. Traditional “hard” or “grey” engineering solutions are proving both expensive and inflexible in the face of a rapidly changing coastal environment. Hybrid solutions that incorporate natural, nature-based, structural, and non-structural features may better achieve a broad set of goals such as ecological enhancement, long-term adaptation, and social benefits, but broad consideration and uptake of these approaches has been slow. One barrier to the widespread implementation of hybrid solutions is the lack of a relatively quick but holistic evaluation framework that places these broader environmental and societal goals on equal footing with the more traditional goal of exposure reduction. To respond to this need, the Adaptive Gradients Framework was developed and pilot-tested as a qualitative, flexible, and collaborative process guide for organizations to understand, evaluate, and potentially select more diverse kinds of infrastructural responses. These responses would ideally include natural, nature-based, and regulatory/cultural approaches, as well as hybrid designs combining multiple approaches. It enables rapid expert review of project designs based on eight metrics called “gradients”, which include exposure reduction, cost efficiency, institutional capacity, ecological enhancement, adaptation over time, greenhouse gas reduction, participatory process, and social benefits. The framework was conceptualized and developed in three phases: relevant factors and barriers were collected from practitioners and experts by survey; these factors were ranked by importance and used to develop the initial framework; several case studies were iteratively evaluated using this technique; and the framework was finalized for implementation. The article presents the framework and a pilot test of its application, along with resources that would enable wider application of the framework by practitioners and theorists.

Description: Sustainability, Vol. 10, Pages 2627: Photovoltaic Power Forecasting Based on EEMD and a Variable-Weight Combination Forecasting Model Sustainability doi: 10.3390/su10082627 Authors: Hui Wang Jianbo Sun Weijun Wang It is widely considered that solar energy will be one of the most competitive energy sources in the future, and solar energy currently accounts for high percentages of power generation in developed countries. However, its power generation capacity is significantly affected by several factors; therefore, accurate prediction of solar power generation is necessary. This paper proposes a photovoltaic (PV) power generation forecasting method based on ensemble empirical mode decomposition (EEMD) and variable-weight combination forecasting. First, EEMD is applied to decompose PV power data into components that are then combined into three groups: low-frequency, intermediate-frequency, and high-frequency. These three groups of sequences are individually predicted by the variable-weight combination forecasting model and added to obtain the final forecasting result. In addition, the design of the weights for combination forecasting was studied during the forecasting process. The comparison in the case study indicates that in PV power generation forecasting, the prediction results obtained by the individual forecasting and summing of the sequences after the EEMD are better than those from direct prediction. In addition, when the single prediction model is converted to a variable-weight combination forecasting model, the prediction accuracy is further improved by using the optimal weights.

Description: Sustainability, Vol. 10, Pages 2622: A Rough Multi-Criteria Decision-Making Approach for Sustainable Supplier Selection under Vague Environment Sustainability doi: 10.3390/su10082622 Authors: Huiyun Lu Shaojun Jiang Wenyan Song Xinguo Ming With the growing awareness of environmental and social issues, sustainable supply chain management (SSCM) has received considerable attention both in academia and industry. Supplier selection plays an important role in the successful implementation of sustainable supply chain management, because it can influence the performance of SSCM. Sustainable supplier selection is a typical multi-criteria decision-making problem involving subjectivity and vagueness. Although some previous researches of supplier selection use fuzzy approaches to deal with vague information, it has been criticized for requiring much priori information and inflexibility in manipulating vagueness. Moreover, the previous methods often omit the environmental and social evaluation criteria in the supplier selection. To manipulate these problems, a new approach based on the rough set theory and ELECTRE (ELimination Et Choix Traduisant la REalité) is developed in this paper. The novel approach integrates the strength of rough set theory in handling vagueness without much priori information and the merit of ELECTRE in modeling multi-criteria decision-making problem. Finally, a case study of sustainable supplier selection for solar air-conditioner manufacturer is provided to demonstrate the application and potential of the approach.

Description: Sustainability, Vol. 10, Pages 2624: Economic Transition and Changing Location of Manufacturing Industry in China: A Study of the Yangtze River Delta Sustainability doi: 10.3390/su10082624 Authors: Jiawei Wu Yehua Dennis Wei Qizhai Li Feng Yuan Industrial restructuring is widely considered an important force in regional economic growth and sustainable development. With increased globalization and economic transition, a dramatic industrial restructuring has been taking place in China. Applying geographically weighted shift-share model (GW-SSM) and geographically and temporally weighted regression model (GTWR), we analyze (re)location dynamics and determinants of the manufacturing industry in the Yangtze River Delta (YRD) from 1999 to 2013, with particular attention to the implications of economic transition and institutional restructuring. We find that high-tech and capital-intensive manufacturing industries agglomerated in coastal cities, while labor-intensive and resource-based sectors have become spatially more dispersed to peripheral areas. We also find that the development of service and high-tech industries, rising labor costs, and more strict environmental regulations have facilitated the geographic dispersion of labor- and pollution-intensive industries. Moreover, regions with advantages in intermediate goods, preferential policies, and urbanization economies are attractive to capital- and technology-intensive manufacturing industries. Our research suggests that development policies should be tailored to specific regions to promote local production and innovative networks and make manufacturing industries more competitive.

Description: Sustainability, Vol. 10, Pages 2621: Adoption of Conservation Tillage on the Semi-Arid Loess Plateau of Northwest China Sustainability doi: 10.3390/su10082621 Authors: Qingfeng Han Kadambot H. M. Siddique Fengmin Li Conservation tillage is an important approach to prevent water loss and soil erosion and promote soil fertility that has been adopted widely throughout the world. However, despite promotion of the benefits of conservation tillage, obstacles are still encountered in some regions. A survey of 385 farmer households in the semi-arid Loess Plateau of China was conducted to assess the adoption of conservation tillage (ACT). This investigation was located in two counties that have run conservation tillage demonstrations with wheat for at least eight years. A binary logistic regression model was used to quantify the factors determining whether or not farmers adopt conservation tillage. Farmer’s education level, the influence of training, and field demonstrations by agricultural departments had significant positive effects on ACT. Although the adoption rate of conservation tillage in this paper was very high (89%), farmers were reluctant to continue practicing conservation tillage based on their experiences, which is contrary to the expectations of the government. The area available for planting winter wheat and the number of arable plots per household also had significant positive effects on ACT. However, the total cultivated area of land per household had a significant negative impact on ACT. Farmer awareness of conservation tillage technology, the distance from a farmer’s house to the nearest agricultural market, and the size of the active labor force in the family had significant negative impacts on ACT. These results will help in the development of more effective and targeted policies to improve the sustainability of farming systems on the semi-arid Loess Plateau.

Description: Sustainability, Vol. 10, Pages 2620: Transition towards Energy Efficiency: Developing the Nigerian Building Energy Efficiency Code Sustainability doi: 10.3390/su10082620 Authors: Susanne Geissler Doris Österreicher Ene Macharm In Nigeria, there is an estimated deficit of 17 million housing units. Power supply is insufficient, and the electricity supply for about 60 million Nigerians relies on private generators, causing noise, pollution, and high expenditures for mainly imported fuel. Altogether, current challenges clearly demonstrate the need for effective energy efficiency policies targeting also the building sector. The Nigerian Energy Support Program began in 2013, among others, with the objective being to support the Nigerian Government in developing the Nigerian Building Energy Efficiency Code. This paper presents two preparatory activities carried out in order to come up with suggestions for a legal framework well suited for the situation on the ground: the Case Study Building Analysis carried out in collaboration with a Nigerian developer and the Nigerian Building Energy Efficiency Guideline, elaborated together with stakeholders. The results of preparatory activities pointed out that the code must put emphasis on climate adaptive design and must define requirements and procedures in a clear and simple way to allow for effective enforcement. Only then can energy-efficient mass housing be feasible in Nigeria. The paper concludes with a description of the Nigerian Building Energy Efficiency Code (BEEC), officially approved and launched by the Federal Minister of Power, Works and Housing on 29 August 2017.

Description: Sustainability, Vol. 10, Pages 2619: Are the World-Leading Primary Silver Mines Exhausting? Sustainability doi: 10.3390/su10082619 Authors: Marcello Ruberti Stefania Massari Silver is one of the rarest metals in nature and certainly among the most used ones, not only as precious good for financial investments but also for many industrial critical applications. Because it would be very difficult to analyze the situation regarding the future global availability of silver as a commodity in general, due to the necessity of a large amount of data which are hardly available, we have focused only on the mining production of primary silver. In particular, the study regards the activities of a sample consisting of twelve of the world top fifteen leading primary silver mines, which represent the 54% of the worldwide primary silver production and 16% of the global silver mining production. We have investigated the related exploitation state and trends of these twelve sites by elaborating their last ten-years statistics on silver production, ore grades, resources and reserves. The findings of this study, in short, are that the cumulative average silver ore grades, both in extracted mineral, resources and reserves, of the above selected mines, have decreased and also that the new mining fields (Dukat, San Bartolomé, Pirquitas, Saucito) have lower silver content indexes than the older ones.

Description: Water, Vol. 10, Pages 989: Computational Study of a Vertical Plunging Jet into Still Water Water doi: 10.3390/w10080989 Authors: Zegao Yin Qianqian Jia Yuan Li Yanxu Wang Dejun Yang The behavior of a vertical plunging jet was numerically investigated using the coupled Level Set and Volume of Fluid method. The computational results were in good agreement with the experimental results reported in the related literature. Vertical plunging jet characteristics, including the liquid velocity field, air void fraction, and turbulence kinetic energy, were explored by varying the distance between the nozzle exit and the still water level. It was found that the velocity at the nozzle exit plays an unimportant role in the shape and size of ascending bubbles. A modified prediction equation between the centerline velocity ratio and the axial distance ratio was developed using the data of the coupled Level Set and Volume of Fluid method, and it showed a better predicting ability than the Level Set and Mixture methods. The characteristics of turbulence kinetic energy, including its maximum value location and its radial and vertical distribution, were also compared with that of submerged jets.

Description: Water, Vol. 10, Pages 984: Vulnerability Analysis of the Venetian Littoral and Adopted Mitigation Strategy Water doi: 10.3390/w10080984 Authors: Piero Ruol Luca Martinelli Chiara Favaretto This paper discusses the key aspects of the recent Coastal Plan of the Veneto Region (IT). Its aim is to propose a single mitigation strategy for coastal erosion that is valid for the whole Veneto Region, and possibly elsewhere, as well as a method to assign a priority level to any action. The suggested mitigation action against erosion depends on urbanization level, beach width, as well as cross-shore and long-shore sediment transport. The criterion used to give a priority level to mitigation actions is based on a vulnerability index that takes into account erosive tendency, existing coastal flooding hazards, coast value, environmental relevance, tourist pressure, urbanization level, the presence of production activities, and cultural heritage. A sample case featuring the littoral of Rosolina is also provided and includes a site description, the sediment budget, critical issues and possible mitigation measures.

Description: Algorithms, Vol. 11, Pages 112: A Novel Parallel Auto-Encoder Framework for Multi-Scale Data in Civil Structural Health Monitoring Algorithms doi: 10.3390/a11080112 Authors: Ruhua Wang Ling Li Jun Li In this paper, damage detection/identification for a seven-storey steel structure is investigated via using the vibration signals and deep learning techniques. Vibration characteristics, such as natural frequencies and mode shapes are captured and utilized as input for a deep learning network while the output vector represents the structural damage associated with locations. The deep auto-encoder with sparsity constraint is used for effective feature extraction for different types of signals and another deep auto-encoder is used to learn the relationship of different signals for final regression. The existing SAF model in a recent research study for the same problem processed all signals in one serial auto-encoder model. That kind of models have the following difficulties: (1) the natural frequencies and mode shapes are in different magnitude scales and it is not logical to normalize them in the same scale in building the models with training samples; (2) some frequencies and mode shapes may not be related to each other and it is not fair to use them for dimension reduction together. To tackle the above-mentioned problems for the multi-scale dataset in SHM, a novel parallel auto-encoder framework (Para-AF) is proposed in this paper. It processes the frequency signals and mode shapes separately for feature selection via dimension reduction and then combine these features together in relationship learning for regression. Furthermore, we introduce sparsity constraint in model reduction stage for performance improvement. Two experiments are conducted on performance evaluation and our results show the significant advantages of the proposed model in comparison with the existing approaches.

Description: Diversity, Vol. 10, Pages 75: Kuschelysius, a New Alpine Genus of Eugnomine Weevil (Coleoptera: Curculionidae: Curculioninae) from New Zealand Diversity doi: 10.3390/d10030075 Authors: Samuel D. J. Brown Richard A. B. Leschen Kuschelysiusnew genus is described for four species, K. hollowayaenew species, K. durusnew species, K. verbalisnew species and K. nitensnew species, which are found in alpine regions along the length of the South Island of New Zealand. The genus most closely resembles members of the genus Eugnomus but is distinguished from them by the presence of a small pair of post-ocular tubercles and by having appressed scales on the dorsal surfaces. Some members of Kuschelysius appear to be flight-capable with well-developed hindwings, while others have reduced hindwings and are presumably flightless. Many specimens have been collected from the flowers of Dracophyllum traversii, Celmisia and other alpine plants, and the guts of examined specimens contained pollen. We hypothesise that the species of Kuschelysius are pollinators of the New Zealand alpine flora.

Description: Water, Vol. 10, Pages 982: Multivariate Chemometric Analysis of Membrane Fouling Patterns in Biofilm Ceramic Membrane Bioreactor Water doi: 10.3390/w10080982 Authors: Olga Kulesha Zakhar Maletskyi Harsha Ratnaweera Membrane fouling highly limits the development of Membrane bioreactor technology (MBR), which is among the key solutions to water scarcity. The current study deals with the determination of the fouling propensity of filtered biomass in a pilot-scale biofilm membrane bioreactor to enable the prediction of fouling intensity. The system was designed to treat domestic wastewater with the application of ceramic microfiltration membranes. Partial least squares regression analysis of the data obtained during the long-term operation of the biofilm-MBR (BF-MBR) system demonstrated that Mixed liquor suspended solids (MLSS), diluted sludge volume index (DSVI), chemical oxygen demand (COD), and their slopes are the most significant for the estimation and prediction of fouling intensity, while normalized permeability and its slope were found to be the most reliable fouling indicators. Three models were derived depending on the applied operating conditions, which enabled an accurate prediction of the fouling intensities in the system. The results will help to prevent severe membrane fouling via the change of operating conditions to prolong the effective lifetime of the membrane modules and to save energy and resources for the maintenance of the system.

Description: Water, Vol. 10, Pages 983: The Mechanical Properties of High Strength Reinforced Cured-in-Place Pipe (CIPP) Liner Composites for Urban Water Infrastructure Rehabilitation Water doi: 10.3390/w10080983 Authors: Hyun Wook Ji Sung Soo Yoo Jonghoon Kim Dan Daehyun Koo Most urban areas in the world have water infrastructure systems, including the buried sewer and water pipelines, which are assessed as in need of extensive rehabilitation. Deterioration by many other factors affects structural integrity. Trenchless technologies such as Cured-in-Place Pipe (CIPP) are now applied in numerous projects while minimizing disturbance in an urban environment. The main purpose of this study is to develop a high strength CIPP material using various composite materials (e.g., glass fiber, carbon fiber, polyester felt, unsaturated polyester resin, and others). Composite samples were made of the materials and tested using three-point bend apparatus to find mechanical properties, which include the flexural modulus, strength, and deflection. A composite combination with glass fibers with thin felt layers shows the best results in mechanical properties. Flexural modulus is a key factor for CIPP liner thickness design. Glass fiber composite yields between four and nine times higher values than the minimum value specified in the American Society for Testing and Materials (ASTM) F1216. This study provides a fundamental baseline for high strength CIPP liners that are capable of using conventional curing technologies.

Description: Sustainability, Vol. 10, Pages 2617: Exploring Twitter for CSR Disclosure: Influence of CEO and Firm Characteristics in Latin American Companies Sustainability doi: 10.3390/su10082617 Authors: Yuli Marcela Suárez-Rico Mauricio Gómez-Villegas María Antonia García-Benau Social networks, which are characterised by accessibility and interactivity, offer great potential for dialogue between companies and stakeholders, for example as platforms for publishing information on aspects of corporate social responsibility (CSR). In this paper, we use a synthetic index to analyse levels of CSR disclosure via Twitter, and identify explanatory variables of this disclosure by studying the demographic characteristics of the Chief Executive Officer (CEO) and of the company. This synthetic index was based on data for 93 companies located in the four countries of the Pacific Alliance (Chile, Colombia, Mexico, and Peru), using categories based on the 2016 Global Reporting Initave (GRI) Standards. The tweets were compiled during a period of two months in 2017, immediately before and after the publication of each CSR report. The synthetic index was taken as the dependent variable and used as the basis for multivariate regression analysis to identify the relationship between the level of CSR disclosure on Twitter and the characteristics of the firm and its CEO. The results obtained show that firms operating in environmentally-sensitive industries present higher levels of CSR disclosure on Twitter than those in other sectors. By country of origin, the Colombian and Chilean companies offered higher levels of disclosure than those in Mexico and Peru. The regression analysis revealed a positive relationship between the firm operating in a sensitive industry and its level of CSR disclosure on Twitter, and an inverse relationship between the latter variable and the tenure of the CEO.

Description: Algorithms, Vol. 11, Pages 113: Improved Parameter Identification Method for Envelope Current Signals Based on Windowed Interpolation FFT and DE Algorithm Algorithms doi: 10.3390/a11080113 Authors: Xiangfeng Su Huaiqing Zhang Lin Chen Ling Qin Lili Yu Envelope current signals are increasingly emerging in power systems, and their parameter identification is particularly necessary for accurate measurement of electrical energy. In order to analyze the envelope current signal, the harmonic parameters, as well as the envelope parameters, need to be calculated. The interpolation fast Fourier transform (FFT) is a widely used approach which can estimate the signal frequency with high precision, but it cannot calculate the envelope parameters of the signal. Therefore, this paper proposes an improved method based on windowed interpolation FFT (WIFFT) and differential evolution (DE). The amplitude and phase parameters obtained through WIFFT and the envelope parameters estimated by the envelope analysis are optimized using the DE algorithm, which makes full use of the performance advantage of DE. The simulation results show that the proposed method can improve the accuracy of the harmonic parameters and the envelope parameter significantly. In addition, it has good anti-noise ability and high precision.

Description: Atmosphere, Vol. 9, Pages 293: The Impact of Mount Washington on the Height of the Boundary Layer and the Vertical Structure of Temperature and Moisture Atmosphere doi: 10.3390/atmos9080293 Authors: Eric Kelsey Adriana Bailey Georgia Murray Discrimination of the type of air mass along mountain slopes can be a challenge and is not commonly performed, but is critical for identifying factors responsible for influencing montane weather, climate, and air quality. A field campaign to measure air mass type and transitions on the summit of Mount Washington, New Hampshire, USA was performed on 19 August 2016. Meteorological observations were taken at the summit and at several sites along the east and west slopes. Ozone concentrations were measured at the summit and on the valley floor. Additionally, water vapor stable isotopes were measured from a truck that drove up and down the Mount Washington Auto Road concurrent with radiosonde launches that profiled the free atmosphere. This multivariate perspective revealed thermal, moisture, and air mass height differences among the free atmosphere, leeward, and windward mountain slopes. Both thermally and mechanically forced upslope flows helped shape these differences by altering the height of the boundary layer with respect to the mountain surface. Recommendations for measurement strategies hoping to develop accurate observational climatologies of air mass exposure in complex terrain are discussed and will be important for evaluating elevation-dependent warming and improving forecasting for weather and air quality.

Description: Atmosphere, Vol. 9, Pages 292: A Mechanism of the Interdecadal Changes of the Global Low-Frequency Oscillation Atmosphere doi: 10.3390/atmos9080292 Authors: Ruowen Yang Quanliang Chen Yuyun Liu Lin Wang Based on the National Center for Environmental Prediction/National Center for Atmospheric Research reanalysis dataset from 1948 to 2009, this study reveals that global low-frequency oscillation features two major temporal bands. One is a quasi-60-day period known as the intraseasonal oscillation (ISO), and the other is a quasi-15-day period known as the quasi-biweekly oscillation (QBWO). After the mid-1970s, both the ISO and QBWO become intensified and more active, and these changes are equivalently barotropic. The primitive barotropic equations are adopted to study the involved mechanism. It reveals that the e-folding time of the least stable modes of both the ISO and QWBO becomes shorter if the model is solved under the atmospheric basic state after the mid-1970s than if solved under the basic state before the mid-1970s. This result suggests that the atmospheric basic flow after the mid-1970s facilitates a more rapid growth of the ISO and QBWO, and thereby an intensification of the low-frequency oscillations at the two bands.

Description: Atmosphere, Vol. 9, Pages 291: A Statistical Parameter Correction Technique for WRF Medium-Range Prediction of Near-Surface Temperature and Wind Speed Using Generalized Linear Model Atmosphere doi: 10.3390/atmos9080291 Authors: Jinmyeong Jeong Seung-Jae Lee A statistical post-processing method was developed to increase the accuracy of numerical weather prediction (NWP) and simulation by matching the daily distribution of predicted temperatures and wind speeds using the generalized linear model (GLM) and parameter correction, considering an increase in model bias when the range of the prediction time lengthens. The Land Atmosphere Modeling Package Weather Research and Forecasting model, which provides 12-day agrometeorological predictions for East Asia, was employed from May 2017 to April 2018. Training periods occurred one month prior to and after the test period (12 days). A probabilistic consideration accounts for the relatively short training period. Based on the total and monthly root mean square error values for each test site, the results show an improvement in the NWP accuracy after bias correction. The spatial distributions in July and January were compared in detail. It was also shown that the physical consistency between temperature and wind speed was retained in the correction procedure, and that the GLM exhibited better performance than the quantile matching method based on monthly Pearson correlation comparison. The characteristics of coastal and mountainous sites are different from inland automatic weather stations, indicating that supplements to cover these distinctive topographic locations are necessary.

Description: Energies, Vol. 11, Pages 1961: A Novel High Efficiency Quasi-Resonant Converter Energies doi: 10.3390/en11081961 Authors: Tianyu Zhu Jianze Wang Yanchao Ji Yiqi Liu In this paper, a new constant-frequency quasi-resonant converter is proposed. Compared with the traditional LLC converter, the proposed converter can effectively reduce the range of the operating frequency. The output voltage is changed to adjust the reactance of the resonant cavity. The proposed converter has a better loss factor. To verify the theoretical analysis and soft-switching condition, a 250 W, 100 V output prototype was built and compared with the full-bridge LLC converter. Analysis and experimental results verify that a smaller operating frequency range and volume of the transformers, a soft-switching condition, and a higher overall efficiency are achieved with the proposed converter.

Description: Energies, Vol. 11, Pages 1957: Dual-Temperature Evaluation of a High-Temperature Insulation System for Liquid-Immersed Transformer Energies doi: 10.3390/en11081957 Authors: Xiaojing Zhang Lu Ren Haichuan Yu Yang Xu Qingquan Lei Xin Li Baojia Han A high-temperature oil–paper insulation system offers an opportunity to improve the overloading capability of distribution transformers facing seasonal load variation. A high-temperature electrical insulation system (EIS) was chosen due to thermal calculation based on a typical loading curve on the China Southern Power Grid. In order to evaluate candidate high-temperature insulation systems, Nomex® T910 (aramid-enhanced cellulose) immersed in FR3 (natural ester) was investigated by a dual-temperature thermal aging test compared with a conventional insulation system, Kraft paper impregnated with mineral oil. Throughout the thermal aging test, mechanical, chemical, and dielectric parameters of both paper and insulating oil were investigated in each aging cycle. The thermal aging results determined that the thermal class of the FR3-T910 insulation system meets the request of overloading transformer needs.

Description: Energies, Vol. 11, Pages 1954: Experimental Study of Flow-Induced Whistling in Pipe Systems Including a Corrugated Section Energies doi: 10.3390/en11081954 Authors: Hee-Chang LIM Faran RAZI When air flows through pipe systems that include a corrugated segment, a whistling tone is generated and increases in intensity with increasing flow velocity. This whistling sound is related to the particular geometry of corrugated pipes, which is in the form of alternating cavities. This whistling is an environmental noise problem as well as a possible structural danger because of the resulting induced vibration. This paper studies the whistling behavior of various pipe systems with a combination of smooth and corrugated pipes through a series of experiments. The considered pipe systems consist of two smooth pipes attached at the upstream and downstream ends of a corrugated segment. Experiments with smooth and corrugated pipes, which had inner diameters of 15.25 and 16.5 mm, respectively, and various lengths, were performed for flow velocities of up to approximately 30 m/s. The minimum and maximum Strouhal numbers (St) obtained during our experiments were 0.25 and 0.38, respectively. For all pipe configurations investigated in this study, the lowest Mach number at which whistling was observed was 0.017, and the maximum was 0.093. The lowest frequency at which whistling was detected in our experiments was 650 Hz, and the highest was 3080 Hz. The results presented in the form of different variables and dimensionless parameters, including the frequency, Mach number, Strouhal number, and Helmholtz number. The average mode gap and number of excited acoustic modes were also taken into account for all considered configurations. The pipe systems with longer corrugated segments had broader whistling ranges than did configurations with shorter segments, indicating that the number of cavities inside the corrugated pipe has a direct effect on whistling. Increasing the smooth pipe length (either upstream or downstream) resulted in a decrease in the average mode gap between successive modes. The number of excited acoustic modes was primarily related to the corrugated segment length, but the smooth pipe length also had a pronounced effect on the excited modes for a constant corrugation length. The highest number of excited modes (13) was seen in the case of corrugated length 450 mm and smooth pipe length (either upstream or downstream) 400 mm while the lowest number of excited modes (1) was observed for corrugated length 250 mm and smooth pipe length (downstream) 300 mm and 400 mm.

Description: Energies, Vol. 11, Pages 1950: Investigation of Injection Strategy of Branched-Preformed Particle Gel/Polymer/Surfactant for Enhanced Oil Recovery after Polymer Flooding in Heterogeneous Reservoirs Energies doi: 10.3390/en11081950 Authors: Hong He Jingyu Fu Baofeng Hou Fuqing Yuan Lanlei Guo Zongyang Li Qing You The heterogeneous phase combination flooding (HPCF) system which is composed of a branched-preformed particle gel (B-PPG), polymer, and surfactant has been proposed to enhance oil recovery after polymer flooding in heterogeneous reservoirs by mobility control and reducing oil–water interfacial tension. However, the high cost of chemicals can make this process economically challenging in an era of low oil prices. Thus, in an era of low oil prices, it is becoming even more essential to optimize the heterogeneous phase combination flooding design. In order to optimize the HPCF process, the injection strategy has been designed such that the incremental oil recovery can be maximized using the corresponding combination of the B-PPG, polymer, and surfactant, thereby ensuring a more economically-viable recovery process. Different HPCF injection strategies including simultaneous injection and alternation injection were investigated by conducting parallel sand pack flooding experiments and large-scale plate sand pack flooding experiments. Results show that based on the flow rate ratio, the pressure rising area and the incremental oil recovery, no matter whether the injection strategy is simultaneous injection or alternation injection of HPCF, the HPCF can significantly block high permeability zone, increase the sweep efficiency and oil displacement efficiency, and effectively improve oil recovery. Compared with the simultaneous injection mode, the alternation injection of HPCF can show better sweep efficiency and oil displacement efficiency. Moreover, when the slug of HPCF and polymer/surfactant with the equivalent economical cost is injected by alternation injection mode, as the alternating cycle increases, the incremental oil recovery increases. The remaining oil distribution at different flooding stages investigated by conducting large-scale plate sand pack flooding experiments shows that alternation injection of HPCF can recover more remaining oil in the low permeability zone than simultaneous injection. Hence, these findings could provide the guidance for developing the injection strategy of HPCF to further enhance oil recovery after polymer flooding in heterogeneous reservoirs in the era of low oil prices.

Description: Entropy, Vol. 20, Pages 560: Ensemble Estimation of Information Divergence † Entropy doi: 10.3390/e20080560 Authors: Kevin R. Moon Kumar Sricharan Kristjan Greenewald Alfred O. Hero Recent work has focused on the problem of nonparametric estimation of information divergence functionals between two continuous random variables. Many existing approaches require either restrictive assumptions about the density support set or difficult calculations at the support set boundary which must be known a priori. The mean squared error (MSE) convergence rate of a leave-one-out kernel density plug-in divergence functional estimator for general bounded density support sets is derived where knowledge of the support boundary, and therefore, the boundary correction is not required. The theory of optimally weighted ensemble estimation is generalized to derive a divergence estimator that achieves the parametric rate when the densities are sufficiently smooth. Guidelines for the tuning parameter selection and the asymptotic distribution of this estimator are provided. Based on the theory, an empirical estimator of Rényi-α divergence is proposed that greatly outperforms the standard kernel density plug-in estimator in terms of mean squared error, especially in high dimensions. The estimator is shown to be robust to the choice of tuning parameters. We show extensive simulation results that verify the theoretical results of our paper. Finally, we apply the proposed estimator to estimate the bounds on the Bayes error rate of a cell classification problem.

Description: Entropy, Vol. 20, Pages 556: Multivariate Multiscale Complexity Analysis of Self-Reproducing Chaotic Systems Entropy doi: 10.3390/e20080556 Authors: Shaobo He Chunbiao Li Kehui Sun Sajad Jafari Designing a chaotic system with infinitely many attractors is a hot topic. In this paper, multiscale multivariate permutation entropy (MMPE) and multiscale multivariate Lempel–Ziv complexity (MMLZC) are employed to analyze the complexity of those self-reproducing chaotic systems with one-directional and two-directional infinitely many chaotic attractors. The analysis results show that complexity of this class of chaotic systems is determined by the initial conditions. Meanwhile, the values of MMPE are independent of the scale factor, which is different from the algorithm of MMLZC. The analysis proposed here is helpful as a reference for the application of the self-reproducing systems.

Description: IJERPH, Vol. 15, Pages 1592: Full-Scale Experimental Study of Groundwater Softening in a Circulating Pellet Fluidized Reactor International Journal of Environmental Research and Public Health doi: 10.3390/ijerph15081592 Authors: Ruizhu Hu Tinglin Huang Aofan Zhi Zhangcheng Tang The softening effect of a new type of circulating pellet fluidized bed (CPFB) reactor on groundwater was studied through a full-scale experiment. The operation of the CPFB reactor in the second water plant in Chang’an District in Xi’an China was monitored for one year, and the results were compared with those for the Amsterdam reactor in The Netherlands. The removal efficiency of Ca2+ in the CPFB reactor reached 90%; the removal rate of total hardness was higher than 60%; effluent pH was 9.5–9.8; the turbidity of the effluent and the turbidity after boiling were lower than 1.0 NTU; the unit cost was less than €0.064 per m3; and the softened effluent was stable. The pellets in the CPFB reactor were circulated, providing higher crystallization efficiency. The diameter of the discharged pellets reached between 3–5 mm, and the fluidized area height of the CPFB reactor was 4 m. The performance parameters of the CFPB reactor were optimized.

Description: IJERPH, Vol. 15, Pages 1596: Predicting Infectious Disease Using Deep Learning and Big Data International Journal of Environmental Research and Public Health doi: 10.3390/ijerph15081596 Authors: Sangwon Chae Sungjun Kwon Donghyun Lee Infectious disease occurs when a person is infected by a pathogen from another person or an animal. It is a problem that causes harm at both individual and macro scales. The Korea Center for Disease Control (KCDC) operates a surveillance system to minimize infectious disease contagions. However, in this system, it is difficult to immediately act against infectious disease because of missing and delayed reports. Moreover, infectious disease trends are not known, which means prediction is not easy. This study predicts infectious diseases by optimizing the parameters of deep learning algorithms while considering big data including social media data. The performance of the deep neural network (DNN) and long-short term memory (LSTM) learning models were compared with the autoregressive integrated moving average (ARIMA) when predicting three infectious diseases one week into the future. The results show that the DNN and LSTM models perform better than ARIMA. When predicting chickenpox, the top-10 DNN and LSTM models improved average performance by 24% and 19%, respectively. The DNN model performed stably and the LSTM model was more accurate when infectious disease was spreading. We believe that this study’s models can help eliminate reporting delays in existing surveillance systems and, therefore, minimize costs to society.

Description: Materials, Vol. 11, Pages 1301: Spiral Bevel Gears Face Roughness Prediction Produced by CNC End Milling Centers Materials doi: 10.3390/ma11081301 Authors: Álvaro Álvarez Amaia Calleja Mikel Arizmendi Haizea González Luis Norberto Lopez de Lacalle The emergence of multitasking machines in the machine tool sector presents new opportunities for the machining of large size gears and short production series in these machines. However, the possibility of using standard tools in conventional machines for gears machining represents a technological challenge from the point of view of workpiece quality. Machining conditions in order to achieve both dimensional and surface quality requirements need to be determined. With these considerations in mind, computer numerical control (CNC) methods to provide useful tools for gear processing are studied. Thus, a model for the prediction of surface roughness obtained on the teeth surface of a machined spiral bevel gear in a multiprocess machine is presented. Machining strategies and optimal machining parameters were studied, and the roughness model is validated for 3 + 2 axes and 5 continuous axes machining strategies.

Description: Materials, Vol. 11, Pages 1302: Enhanced Cycling Stability of LiCuxMn1.95−xSi0.05O4 Cathode Material Obtained by Solid-State Method Materials doi: 10.3390/ma11081302 Authors: Hongyuan Zhao Fang Li Xiuzhi Bai Tingting Wu Zhankui Wang Yongfeng Li Jianxiu Su The LiCuxMn1.95−xSi0.05O4 (x = 0, 0.02, 0.05, 0.08) samples have been obtained by a simple solid-state method. XRD and SEM characterization results indicate that the Cu-Si co-doped spinels retain the inherent structure of LiMn2O4 and possess uniform particle size distribution. Electrochemical tests show that the optimal Cu-doping amount produces an obvious improvement effect on the cycling stability of LiMn1.95Si0.05O4. When cycled at 0.5 C, the optimal LiCu0.05Mn1.90Si0.05O4 sample exhibits an initial capacity of 127.3 mAh g−1 with excellent retention of 95.7% after 200 cycles. Moreover, when the cycling rate climbs to 10 C, the LiCu0.05Mn1.90Si0.05O4 sample exhibits 82.3 mAh g−1 with satisfactory cycling performance. In particular, when cycled at 55 °C, this co-doped sample can show an outstanding retention of 94.0% after 100 cycles, whiles the LiMn1.95Si0.05O4 only exhibits low retention of 79.1%. Such impressive performance shows that the addition of copper ions in the Si-doped spinel effectively remedy the shortcomings of the single Si-doping strategy and the Cu-Si co-doped spinel can show excellent cycling stability.

Description: Forests, Vol. 9, Pages 459: Pedunculate and Sessile Mixed Oak Forest Regeneration Process in Lithuania Forests doi: 10.3390/f9080459 Authors: Girmantė Jurkšienė Virginijus Baliuckas Pedunculate and sessile oak species are sympatric. These oaks hybridize with one another, and this process influences the development of undergrowth. The purpose of this study was to determine how different oak species influence the forest regeneration process. For this purpose, the forest was divided into eight transects of 300 m and 100 m widths, distinguished into temporary plots of 10 m in diameter covering the whole territory of the forest. The distribution of oak undergrowth was calculated by four oak height groups, determining the composition of the first storey, covering of underbrush and herbaceous plant, and forest site. We determined that the spread of oak differed depending on the first storey tree species and underbrush. Grass cover was the biggest influence on the sessile oak. The impurity of sessile oak in oak stands had a positive impact on the development of undergrowth, since the entire undergrowth develops faster than separate components of the undergrowth.

Description: Forests, Vol. 9, Pages 455: Measuring Eco-Efficiency of State-Owned Forestry Enterprises in Northeast China Forests doi: 10.3390/f9080455 Authors: Youliang Ning Zhen Liu Zekui Ning Han Zhang State-owned forestry enterprises (SOFEs) play an important role in the forestry economy in China. Understanding the eco-efficiency of their production is beneficial for the development of sustainable forestry and for achieving Goal 8 of the United Nations’ Sustainable Development Goals (SDGs): Decent Work and Economic Growth. This paper assesses SOFEs’ overall eco-efficiency by analyzing various undesirable outputs using the Slacks-Based Measure of efficiency in Data Envelopment Analysis (SBM-DEA) model. Using basic data from 87 SOFEs in Northeast China from 2003 to 2016, this paper evaluated the eco-efficiency development level and spatial patterns of that region. The results show that SOFEs’ low eco-efficiency was caused by low pure-technical efficiency. Regional differences in eco-efficiency were very significant and became larger, but a market-oriented reform might help to improve such efficiency. The eco-efficiency of SOFEs was in decline from 2003 to 2016 due to the implementation of the Natural Forest Protection Project (NFPP). However, due to a relative lack of production factor inputs, most SOFEs’ scale returns are now increasing. In the future, efforts should be made to promote market-oriented reforms and take the path of large-scale development.

Description: Minerals, Vol. 8, Pages 323: (10.4) Face of Ordered and Disordered Dolomite, MgCa(CO3)2: A Computational Study to Reveal the Growth Mechanism Minerals doi: 10.3390/min8080323 Authors: Marco Bruno Erica Bittarello In this study, the stability of the (10.4) face of dolomite was systematically investigated. The surface energies at 0 K of the different (10.4) surfaces resulting from the cut of both ordered and disordered bulk structures were determined and compared, to establish how different atomic configurations (surface terminations) can affect the stability of the investigated face. To study the thermodynamic behavior of a surface, a 2D periodic slab model and the ab initio CRYSTAL code were adopted. The surface energies of the (10.4) faces of calcite and magnesite were also calculated in order to compare them with those of the different terminations of the (10.4) face of dolomite. Our calculations showed that the bulk of the dolomite crystal must have an ordered structure to reach the minimum of the energy, whereas the (10.4) surface is more stable when its structure is disordered. A growth model of the (10.4) face has been proposed: the peculiarity of this model consists in the existence of some disordered layers forming at the interface crystal/solution, which arrange in an ordered structure once covered by others disordered layers resulting by the spiral steps propagation.

Description: Materials, Vol. 11, Pages 1297: A Straightforward Substitution Strategy to Tune BODIPY Dyes Spanning the Near-Infrared Region via Suzuki–Miyaura Cross-Coupling Materials doi: 10.3390/ma11081297 Authors: Guanglei Li Yu Otsuka Takuya Matsumiya Toshiyuki Suzuki Jianye Li Masashi Takahashi Koji Yamada In this study, a series of new red and near-infrared (NIR) dyes derived from 4,4-difluoro-4-bora-3a,4a-diaza-s-indacene (BODIPY) were developed by introducing thiophene and its derivatives to the 3- and 5- positions of the dichloroBODIPY core. For the first time, cyclictriol boronates and N-methyliminodiacetic acid (MIDA) boronate were used as organoboron species to couple with 3,5-dichloroBODIPY via the one-step Suzuki–Miyaura cross-coupling. Six kinds of thieno-expended BODIPY dyes were synthesized in acceptable yields ranging from 31% to 79%. All six dyes showed different absorption and emission wavelengths spanning a wide range (c.a. 600–850 nm) in the red and NIR regions with relatively high quantum yields (19–85%). Cellular imaging of 8-(2,6-dimethylphenyl)-re3,5-di(2-thienyl)-BODIPY (dye 1) was conducted using bovine cumulus cells, and the fluorescence microscopy images indicated that the chromophore efficiently accumulated and was exclusively localized in the cytoplasm, suggesting it could be utilized as a subcellular probe. All six dyes were characterized using 1H-NMR and mass spectrometry.

Description: Minerals, Vol. 8, Pages 322: Particle Size Distribution Effects on the Strength Characteristic of Cemented Paste Backfill Minerals doi: 10.3390/min8080322 Authors: Jiangyu Wu Meimei Feng Zhanqing Chen Xianbiao Mao Guansheng Han Yiming Wang It is of great significance, for economic, environmental and security reasons, to investigate the strength characteristic of underground cemented paste backfill (CPB). Consequently, an ultrasonic test, uniaxial and triaxial compression experiment, and acoustic emission (AE) monitoring were carried out on CPB, for which the particles satisfied Talbot gradation. The homogeneity of CPB specimens was evaluated by ultrasonic pulse velocity (UPV). The stress–strain behavior and AE characteristic of CPB specimens under different Talbot indices and confining pressures were investigated. The effects of the particle size distribution and the confining pressure on the peak strength of CPB were analyzed. The strength parameter model of CPB under the coupled influence of the particle size distribution and the confining pressure was constructed based on the Mohr–Coulomb strength criterion. The results show that the peak strength of CPB is positively linear with confining pressure, however, the relationship between its strength parameters and the Talbot index can be characterized by a quadratic polynomial function. This suggests that there is an optimal gradation of particles reflected in the maximum strength of CPB.

Description: Minerals, Vol. 8, Pages 319: Fault Zone Evolution and Development of a Structural and Hydrological Barrier: The Quartz Breccia in the Kiggavik Area (Nunavut, Canada) and Its Control on Uranium Mineralization Minerals doi: 10.3390/min8080319 Authors: Alexis Grare Olivier Lacombe Julien Mercadier Antonio Benedicto Marie Guilcher Anna Trave Patrick Ledru John Robbins In the Kiggavik area (Nunavut, Canada), major fault zones along, or close to, where uranium deposits are found are often associated with occurrence of thick quartz breccia (QB) bodies. These bodies formed in an early stage (~1750 Ma) of the long-lasting tectonic history of the Archean basement, and of the Proterozoic Thelon basin. The main characteristics of the QB are addressed in this study; through field work, macro and microscopic observations, cathodoluminescence microscopy, trace elements, and oxygen isotopic signatures of the quartz forming the QB. Faults formed earlier during syn- to post-orogenic rifting (1850–1750 Ma) were subsequently reactivated, and underwent cycles of cataclasis, pervasive silicification, hydraulic brecciation, and quartz recrystallization. This was synchronous with the circulation of meteoric fluids mixing with Si-rich magmatic-derived fluids at depth, and were coeval with the emplacement of the Kivalliq igneous suite at 1750 Ma. These processes led to the emplacement of up to 30 m thick QB, which behaved as a mechanically strong, transverse hydraulic barrier that localized later fracturing, and compartmentalized/channelized vertical flow of uranium-bearing fluids after the deposition of the Thelon Basin (post 1750 Ma). The development and locations of QB control the location of uranium mineralization in the Kiggavik area.

Description: IJERPH, Vol. 15, Pages 1597: Assessing Heat-Related Mortality Risks among Rural Populations: A Systematic Review and Meta-Analysis of Epidemiological Evidence International Journal of Environmental Research and Public Health doi: 10.3390/ijerph15081597 Authors: Emmanuel A. Odame Ying Li Shimin Zheng Ambarish Vaidyanathan Ken Silver Most epidemiological studies of high temperature effects on mortality have focused on urban settings, while heat-related health risks in rural areas remain underexplored. To date there has been no meta-analysis of epidemiologic literature concerning heat-related mortality in rural settings. This study aims to systematically review the current literature for assessing heat-related mortality risk among rural populations. We conducted a comprehensive literature search using PubMed, Web of Science, and Google Scholar to identify articles published up to April 2018. Key selection criteria included study location, health endpoints, and study design. Fourteen studies conducted in rural areas in seven countries on four continents met the selection criteria, and eleven were included in the meta-analysis. Using the random effects model, the pooled estimates of relative risks (RRs) for all-cause and cardiovascular mortality were 1.030 (95% CI: 1.013, 1.048) and 1.111 (95% CI: 1.045, 1.181) per 1 °C increase in daily mean temperature, respectively. We found excess risks in rural settings not to be smaller than risks in urban settings. Our results suggest that rural populations, like urban populations, are also vulnerable to heat-related mortality. Further evaluation of heat-related mortality among rural populations is warranted to develop public health interventions in rural communities.

Description: IJERPH, Vol. 15, Pages 1595: Does SuperPark Make Children Less Sedentary? How Visiting a Commercial Indoor Activity Park Affects 7 to 12 Years Old Children’s Daily Sitting and Physical Activity Time International Journal of Environmental Research and Public Health doi: 10.3390/ijerph15081595 Authors: Arto J. Pesola Martti Melin Anssi Vanhala Ying Gao Taija Finni Commercial indoor activity parks provide children with a variety of entertaining physical activities. This study examined whether visiting SuperPark affects total daily sitting and physical activity time. The participants (8 girls and 7 boys, aged 10.3 ± 1.9 years, height 144.5 ± 11.8 cm, body mass index (BMI) 19.3 ± 3.0 kg/m2) wore a thigh-worn accelerometer during a normal week and were provided free tickets to visit SuperPark on at least one day. On average, the children spent 3.3 ± 1.2 h in SuperPark. During the visits the children had 0.9 h less sitting (0.7 ± 0.3 h, p = 0.000) and 0.9 h more moderate-to-vigorous physical activity (MVPA; 1.4 ± 0.6 h, p = 0.002) as compared to the reference periods on days without a SuperPark visit (1.6 ± 0.3 h sitting and 0.5 ± 0.4 h MVPA). During the days when visiting SuperPark, sitting time decreased 1.0 h (5.8 ± 0.9 h, p = 0.008) and MVPA increased 0.8 h (3.0 ± 1.0 h, p = 0.017) as compared to the reference days (6.8 ± 1.1 h sitting and 2.2 ± 0.8 h MVPA). The effects were more pronounced during weekdays than weekends. The children spent more than three hours in SuperPark on one visit, of which almost a half was MVPA. During the whole day, one hour of sitting was replaced with MVPA, suggesting that visiting SuperPark has the potential to improve health. Whether children continue visiting SuperPark and gain health benefits merits investigation.

Description: IJGI, Vol. 7, Pages 300: A Comparative Study of Three Non-Geostatistical Methods for Optimising Digital Elevation Model Interpolation ISPRS International Journal of Geo-Information doi: 10.3390/ijgi7080300 Authors: Serajis Salekin Jack H. Burgess Justin Morgenroth Euan G. Mason Dean F. Meason It is common to generate digital elevation models (DEMs) from aerial laser scanning (ALS) data. However, cost and lack of knowledge may preclude its use. In contrast, global navigation satellite systems (GNSS) are seldom used to collect and generate DEMs. These receivers have the potential to be considered as data sources for DEM interpolation, as they can be inexpensive, easy to use, and mobile. The data interpolation method and spatial resolution from this method needs to be optimised to create accurate DEMs. Moreover, the density of GNSS data is likely to affect DEM accuracy. This study investigates three different deterministic approaches, in combination with spatial resolution and data thinning, to determine their combined effects on DEM accuracy. Digital elevation models were interpolated, with resolutions ranging from 0.5 m to 10 m using natural neighbour (NaN), topo to raster (ANUDEM), and inverse distance weighted (IDW) methods. The GNSS data were thinned by 25% (0.389 points m−2), 50% (0.259 points m−2), and 75% (0.129 points m−2) and resulting DEMs were contrast against a DEM interpolated from unthinned data (0.519 points m−2). Digital elevation model accuracy was measured by root mean square error (RMSE) and mean absolute error (MAE). It was found that the highest resolution, 0.5 m, produced the lowest errors in resulting DEMs (RMSE = 0.428 m, MAE = 0.274 m). The ANUDEM method yielded the greatest DEM accuracy from a quantitative perspective (RMSE = 0.305 m and MAE = 0.197 m); however, NaN produced a more visually appealing surface. In all the assessments, IDW showed the lowest accuracy. Thinning the input data by 25% and even 50% had relatively little impact on DEM quality; however, accuracy decreased markedly at 75% thinning (0.129 points m−2). This study showed that, in a time where ALS is commonly used to generate DEMs, GNSS-surveyed data can be used to create accurate DEMs. This study confirmed the need for optimization to choose the appropriate interpolation method and spatial resolution in order to produce a reliable DEM.

Description: IJERPH, Vol. 15, Pages 1593: Modeling Land Use Changes and their Impacts on Non-Point Source Pollution in a Southeast China Coastal Watershed International Journal of Environmental Research and Public Health doi: 10.3390/ijerph15081593 Authors: Xin Zhang Lin Zhou Yuqi Liu Changes in landscape patterns in a river basin play a crucial role in the change on load of non-point source pollution. The spatial distribution of various land use types affects the transmission of non-point source pollutants on the basis of source-sink theory in landscape ecology. Jiulong River basin in southeast of China was selected as the study area in this paper. Aiming to analyze the correlation between changing landscape patterns and load of non-point source pollution in this area, traditional landscape metrics and the improved location-weighted landscape contrast index based on the minimum hydrological response unit (HRULCI) were applied in this study, in combination with remote sensing and geographic information system (GIS) technique. The results of the landscape metrics showed the enhanced fragmentation extent and the decreasing polymerization degree of the overall landscape in the watershed. High values of HRULCI were concentrated in cultivated land, while low HRULCI values mostly appeared in forestland, indicating that cultivated land substantially enhanced non-point source pollution, while forestland inhibited the pollution process.

Description: Remote Sensing, Vol. 10, Pages 1186: Application of Multi-Sensor Satellite Data for Exploration of Zn–Pb Sulfide Mineralization in the Franklinian Basin, North Greenland Remote Sensing doi: 10.3390/rs10081186 Authors: Amin Beiranvand Pour Tae-Yoon S. Park Yongcheol Park Jong Kuk Hong Basem Zoheir Biswajeet Pradhan Iman Ayoobi Mazlan Hashim Geological mapping and mineral exploration programs in the High Arctic have been naturally hindered by its remoteness and hostile climate conditions. The Franklinian Basin in North Greenland has a unique potential for exploration of world-class zinc deposits. In this research, multi-sensor remote sensing satellite data (e.g., Landsat-8, Phased Array L-band Synthetic Aperture Radar (PALSAR) and Advanced Spaceborne Thermal Emission and Reflection Radiometer (ASTER)) were used for exploring zinc in the trough sequences and shelf-platform carbonate of the Franklinian Basin. A series of robust image processing algorithms was implemented for detecting spatial distribution of pixels/sub-pixels related to key alteration mineral assemblages and structural features that may represent potential undiscovered Zn–Pb deposits. Fusion of Directed Principal Component Analysis (DPCA) and Independent Component Analysis (ICA) was applied to some selected Landsat-8 mineral indices for mapping gossan, clay-rich zones and dolomitization. Major lineaments, intersections, curvilinear structures and sedimentary formations were traced by the application of Feature-oriented Principal Components Selection (FPCS) to cross-polarized backscatter PALSAR ratio images. Mixture Tuned Matched Filtering (MTMF) algorithm was applied to ASTER VNIR/SWIR bands for sub-pixel detection and classification of hematite, goethite, jarosite, alunite, gypsum, chalcedony, kaolinite, muscovite, chlorite, epidote, calcite and dolomite in the prospective targets. Using the remote sensing data and approaches, several high potential zones characterized by distinct alteration mineral assemblages and structural fabrics were identified that could represent undiscovered Zn–Pb sulfide deposits in the study area. This research establishes a straightforward/cost-effective multi-sensor satellite-based remote sensing approach for reconnaissance stages of mineral exploration in hardly accessible parts of the High Arctic environments.

Description: Remote Sensing, Vol. 10, Pages 1184: An Evaluation of Forest Health Insect and Disease Survey Data and Satellite-Based Remote Sensing Forest Change Detection Methods: Case Studies in the United States Remote Sensing doi: 10.3390/rs10081184 Authors: Ian W. Housman Robert A. Chastain Mark V. Finco The Operational Remote Sensing (ORS) program leverages Landsat and MODIS data to detect forest disturbances across the conterminous United States (CONUS). The ORS program was initiated in 2014 as a collaboration between the US Department of Agriculture Forest Service Geospatial Technology and Applications Center (GTAC) and the Forest Health Assessment and Applied Sciences Team (FHAAST). The goal of the ORS program is to supplement the Insect and Disease Survey (IDS) and MODIS Real-Time Forest Disturbance (RTFD) programs with imagery-derived forest disturbance data that can be used to augment traditional IDS data. We developed three algorithms and produced ORS forest change products using both Landsat and MODIS data. These were assessed over Southern New England and the Rio Grande National Forest. Reference data were acquired using TimeSync to conduct an independent accuracy assessment of IDS, RTFD, and ORS products. Overall accuracy for all products ranged from 71.63% to 92.55% in the Southern New England study area and 63.48% to 79.13% in the Rio Grande National Forest study area. While the accuracies attained from the assessed products are somewhat low, these results are similar to comparable studies. Although many ORS products met or exceeded the overall accuracy of IDS and RTFD products, the differences were largely statistically insignificant at the 95% confidence interval. This demonstrates the current implementation of ORS is sufficient to provide data to augment IDS data.

Description: Sensors, Vol. 18, Pages 2448: Application-Aware Anomaly Detection of Sensor Measurements in Cyber-Physical Systems Sensors doi: 10.3390/s18082448 Authors: Amin Ghafouri Aron Laszka Koutsoukos Detection errors such as false alarms and undetected faults are inevitable in any practical anomaly detection system. These errors can create potentially significant problems in the underlying application. In particular, false alarms can result in performing unnecessary recovery actions while missed detections can result in failing to perform recovery which can lead to severe consequences. In this paper, we present an approach for application-aware anomaly detection (AAAD). Our approach takes an existing anomaly detector and configures it to minimize the impact of detection errors. The configuration of the detectors is chosen so that application performance in the presence of detection errors is as close as possible to the performance that could have been obtained if there were no detection errors. We evaluate our result using a case study of real-time control of traffic signals, and show that the approach outperforms significantly several baseline detectors.

Description: Sensors, Vol. 18, Pages 2444: Utilization of Inexpensive Carbon-Based Substrates as Platforms for Sensing Sensors doi: 10.3390/s18082444 Authors: Minh Tran Ahmad Fallatah Alison Whale Sonal Padalkar Gold (Au) has been widely used as a material for Surface Enhanced Raman Spectroscopy (SERS) due to its plasmonic properties, stability and biocompatibility. Conventionally for SERS application, Au is deposited on a rigid substrate such as glass or silicon. The rigid substrates severely limit analyte collection efficiency as well as portability. Here, flexible substrates like carbon cloth and carbon paper were investigated as potential substrate candidates for SERS application. The flexible substrates were coated with Au nanostructures by electrodeposition. Model analyte, Rhodamine 6G was utilized to demonstrate the capabilities of the flexible SERS substrates. Additionally, the pesticide paraoxon was also detected on the flexible SERS substrates as well as on a real sample like the apple fruit.

Description: Sensors, Vol. 18, Pages 2441: A Label-Free Fluorescent Assay for the Rapid and Sensitive Detection of Adenosine Deaminase Activity and Inhibition Sensors doi: 10.3390/s18082441 Authors: Xinxing Tang Kefeng Wu Han Zhao Mingjian Chen Changbei Ma Adenosine deaminase (ADA), able to catalyze the irreversible deamination of adenosine into inosine, can be found in almost all tissues and plays an important role in several diseases. In this work, we developed a label-free fluorescence method for the detection of adenosine deaminase activity and inhibition. In the presence of ADA, ATP has been shown to be hydrolyzed. The ATP aptamer was shown to form a G-quadruplex/thioflavin T (ThT) complex with ThT and exhibited an obvious fluorescence signal. However, the ATP aptamer could bind with ATP and exhibited a low fluorescence signal because of the absence of ADA. This assay showed high sensitivity to ADA with a detection limit of 1 U/L based on an SNR of 3 and got a good linear relationship within the range of 1–100 U/L with R2 = 0.9909. The LOD is lower than ADA cutoff value (4 U/L) in the clinical requirement and more sensitive than most of the reported methods. This technique exhibited high selectivity for ADA against hoGG I, UDG, RNase H and λexo. Moreover, this strategy was successfully applied for assaying the inhibition of ADA using erythro-9-(2-hydroxy-3-nonyl) adenine (EHNA) and, as such, demonstrated great potential for the future use in the diagnosis of ADA-relevant diseases, particularly in advanced drug development.

Description: Sensors, Vol. 18, Pages 2440: A Privacy Preserving Scheme for Nearest Neighbor Query Sensors doi: 10.3390/s18082440 Authors: Yuhang Wang Zhihong Tian Hongli Zhang Shen Su Wei Shi In recent years, location privacy concerns that arise when using the nearest neighbor query services have gained increasing attention, as such services have become pervasive in mobile social networks devices and the IoT environments. State-of-the-art privacy preservation schemes focus on the obfuscation of the location information, which has suffered from various privacy attacks and the tradeoff of the quality of service. By noticing the fact that the user’s location could be replaced by their surrounding wireless sensor infrastructures in proximity, in this paper, we propose a wireless sensor access point-based scheme for the nearest neighbor query, without using the location of the user. Then, a noise-addition-based method that preserves user’s location privacy was proposed. To further strengthen the adaptability of the approach to real-world environments, several performance-enhancing methods are introduced, including an R-tree-based Noise-Data Retrieval Algorithm (RNR), and a nearest neighbor query method based on our research. Both performance and security evaluations are conducted to validate our approach. The results show the effectiveness and the practicality of our work.

Description: Water, Vol. 10, Pages 993: Understanding Fundamental Phenomena Affecting the Water Conservation Technology Adoption of Residential Consumers Using Agent-Based Modeling Water doi: 10.3390/w10080993 Authors: Kambiz Rasoulkhani Brianne Logasa Maria Presa Reyes Ali Mostafavi More than one billion people will face water scarcity within the next ten years due to climate change and unsustainable water usage, and this number is only expected to grow exponentially in the future. At current water use rates, supply-side demand management is no longer an effective way to combat water scarcity. Instead, many municipalities and water agencies are looking to demand-side solutions to prevent major water loss. While changing conservation behavior is one demand-based strategy, there is a growing movement toward the adoption of water conservation technology as a way to solve water resource depletion. Installing technology into one’s household requires additional costs and motivation, creating a gap between the overall potential households that could adopt this technology, and how many actually do. This study identified and modeled a variety of demographic and household characteristics, social network influence, and external factors such as water price and rebate policy to see their effect on residential water conservation technology adoption. Using Agent-based Modeling and data obtained from the City of Miami Beach, the coupled effects of these factors were evaluated to examine the effectiveness of different pathways towards the adoption of more water conservation technologies. The results showed that income growth and water pricing structure, more so than any of the demographic or building characteristics, impacted household adoption of water conservation technologies. The results also revealed that the effectiveness of rebate programs depends on conservation technology cost and the affluence of the community. Rebate allocation did influence expensive technology adoption, with the potential to increase the adoption rate by 50%. Additionally, social network connections were shown to have an impact on the rate of adoption independent of price strategy or rebate status. These findings will lead the way for municipalities and other water agencies to more strategically implement interventions to encourage household technology adoption based on the characteristics of their communities.

Description: Algorithms, Vol. 11, Pages 114: Revisiting Chameleon Sequences in the Protein Data Bank Algorithms doi: 10.3390/a11080114 Authors: Mihaly Mezei The steady growth of the Protein Data Bank (PDB) suggests the periodic repetition of searches for sequences that form different secondary structures in different protein structures; these are called chameleon sequences. This paper presents a fast (nlog(n)) algorithm for such searches and presents the results on all protein structures in the PDB. The longest such sequence found consists of 20 residues.

Description: Algorithms, Vol. 11, Pages 115: Color-Based Image Retrieval Using Proximity Space Theory Algorithms doi: 10.3390/a11080115 Authors: Jing Wang Lidong Wang Xiaodong Liu Yan Ren Ye Yuan The goal of object retrieval is to rank a set of images by their similarity compared with a query image. Nowadays, content-based image retrieval is a hot research topic, and color features play an important role in this procedure. However, it is important to establish a measure of image similarity in advance. The innovation point of this paper lies in the following. Firstly, the idea of the proximity space theory is utilized to retrieve the relevant images between the query image and images of database, and we use the color histogram of an image to obtain the Top-ranked colors, which can be regard as the object set. Secondly, the similarity is calculated based on an improved dominance granule structure similarity method. Thus, we propose a color-based image retrieval method by using proximity space theory. To detect the feasibility of this method, we conducted an experiment on COIL-20 image database and Corel-1000 database. Experimental results demonstrate the effectiveness of the proposed framework and its applications.

Description: Atmosphere, Vol. 9, Pages 294: The Influence of the North Atlantic Oscillation Index on Emergency Ambulance Calls for Elevated Arterial Blood Pressure Atmosphere doi: 10.3390/atmos9080294 Authors: Jone Vencloviene Agne Braziene Jurate Zaltauskaite Paulius Dobozinskas The North Atlantic Oscillation (NAO) is the most prominent pattern of atmospheric variability over the middle and high latitudes of the Northern Hemisphere, especially during the cold season. It is found that “weather types” are associated with human health. It is possible that variations in NAO indices (NAOI) had additional impact on human health. We investigated the association between daily emergency ambulance calls (EACs) for exacerbation of essential hypertension and the NAOI by using Poisson regression, adjusting for season, weather variables and exposure to CO, particulate matter and ozone. An increased risk of EACs was associated with NAOI < −0.5 (Rate Ratio (RR) = 1.07, p = 0.013) and NAOI > 0.5 (RR = 1.06, p = 0.004) with a lag of 2 days as compared to −0.5 ≤ NAOI ≤ 0.5. The impact of NAOI > 0.5 was stronger during November-March (RR = 1.10, lag = 0, p = 0.026). No significant associations were found between the NAOI and EACs during 8:00–13:59. An elevated risk was associated during 14:00–21:59 with NAOI < −0.5 (RR = 1.09, p = 0.003) and NAOI > 0.5 (RR = 1.09, p = 0.019) and during 22:00–7:59 with NAOI < −0.5 (RR = 1.12, lag = 1, p = 0.001). The non-linear associations were found between the NAO and EACs. The different impact of the NAO was found during the periods November–March and April–October. The impact of the NAOI was not identical for different times of the day.

Description: Energies, Vol. 11, Pages 1966: Possible Interactions and Interferences of Copper, Chromium, and Arsenic during the Gasification of Contaminated Waste Wood Energies doi: 10.3390/en11081966 Authors: Shurooq Badri Al-Badri Ying Jiang Stuart Thomas Wagland A considerable proportion (about 64%) of biomass energy is produced from woody biomass (wood and its wastes). However, waste wood (WW) is very often contaminated with metal(loid) elements at concentrations leading to toxicity emissions and damages to facilities during thermal conversion. Therefore, procedures for preventing and/or alleviating the negative impacts of these elements require further development, particularly by providing informative and supportive information regarding the phase transformations of the metal(loid)s during thermal conversion processes. Although it is well known that phase transformation depends on different factors such as elements’ vaporization characteristics, operational conditions, and process configuration; however, the influences of reaction atmosphere composition in terms of interactions and interferences are rarely addressed. In response, since Cu, Cr, and As (CCA-elements) are the most regulated elements in woody biomass, this paper aims to explore the possible interactions and interferences among CCA-elements themselves and with Ca, Na, S, Cl, Fe, and Ni from reaction atmosphere composition perspectives during the gasification of contaminated WW. To do so, thermodynamic equilibrium calculations were performed for Boudouard reaction (BR) and partial combustion reaction (PCR) with temperature ranges of 0–1300 °C and 0–1800 °C, respectively, and both reactions were simulated under pressure conditions of 1, 20, and 40 atm. Refinement of the occurred interactions and interferences reveals that Ni-As interactions generate dominant species As2Ni5 and As8Ni11, which increase the solid–gaseous transformation temperature of As. Moreover, the interactions between Ca and Cr predominantly form C3Cr7; whereas the absence of Ca leads to Cr2Na2O4 causing instability in the Cr phase transformation.

Description: Energies, Vol. 11, Pages 1967: Dry Fuel Jet Half-Angle Measurements and Correlation for an Entrained Flow Gasifier Energies doi: 10.3390/en11081967 Authors: Francis Kus Robin Hughes Arturo Macchi Poupak Mehrani Marc Duchesne Reduced order models (ROMs) are increasingly applied to entrained flow gasification development due to reduced computational requirements relative to computational fluid dynamics (CFD) models. However, they require greater a posteriori knowledge of the reactor physics. A significant parameter influencing ROM outputs is the jet half-angle of the solid fuel and oxidant mixture in the gasifier. Thus, it is important to understand the geometry of the jet in the gasifier, and how it is dependent on operating parameters, such as solid and carrier gas flow rates. In this work, an existing model for jet half-angles, which considers the ratio of surrounding gas density to jet core density, is extended to a dry solids jet with impinging gas. The model is fitted to experimental jet half-angles. The jet half-angle of a non-reactive flow was measured using laser-sheet imaging for solid fluxes in the range of 460–880 kg/m2·s and carrier gas fluxes in the range of 43–90 kg/m2·s at the transport line outlet. Jet half-angles ranged from 5.6° to 11.3°, increasing with lower solid/gas loading ratios. CFD simulations of two reactive conditions, with solid and gas fluxes similar to experiments, were used to test the applicability of the proposed jet half-angle model.

Description: Water, Vol. 10, Pages 994: Predicting Lake Eutrophication Responses to Multiple Scenarios of Lake Restoration: A Three-Dimensional Modeling Approach Water doi: 10.3390/w10080994 Authors: Yanping Wang Weiping Hu Zhaoliang Peng Ye Zeng Karsten Rinke To improve the water quality and alleviate the eutrophication of Lake Yangchenghu, the third largest freshwater body within the Lake Taihu basin in China and an important source of drinking water, nutrient reduction strategies should be urgently addressed by decision makers, since virtually no improvement of water quality has taken place since the mid-1990s. Due to the lack of sufficient observation data and simulation results, a vertically compressed three-dimensional numerical model, the EcoTaihu model, was used to study the impact of three restoration measures on the water quality—namely, total nitrogen (TN), total phosphorus (TP) and biomass of phytoplankton (BP)—of Lake Yangchenghu: (i) total nutrient reduction, (ii) intensification of flushing by water transfer, and (iii) spatial adjustment of inflow channels. In particular, the spatial effects of the three restoration measures on the water quality were investigated. The results showed that the EcoTaihu model is applicable to other shallow lakes in China. The water quality responses to the different restoration scenarios showed significant spatio-temporal differences. The reduction of nutrient loads from inflows appeared to be the most effective measure for controlling the eutrophication and algal blooms in Lake Yangchenghu. The effectiveness of water transfer on the improvement of water quality for TN and TP was more influenced by the differences of nutrient concentrations between the transferred water and lake water, rather than flow rate, since no proportionate increase of improvement was observable in the case of larger transferred rates (60 m3 s−1). The spatial narrowing of inflowing rivers in the southwestern lake could preferentially improve the water quality in the southern bay of the western lake, but would also result in a deterioration trend of water quality in the total lake and drinking water abstraction areas.

Description: Energies, Vol. 11, Pages 1968: A Review on Recent Advances and Future Trends of Transformerless Inverter Structures for Single-Phase Grid-Connected Photovoltaic Systems Energies doi: 10.3390/en11081968 Authors: Kamran Zeb Imran Khan Waqar Uddin Muhammad Adil Khan P. Sathishkumar Tiago Davi Curi Busarello Iftikhar Ahmad H. J. Kim The research significance of various scientific aspects of photovoltaic (PV) systems has increased over the past decade. Grid-tied inverters the vital elements for the effective interface of Renewable Energy Resources (RER) and utility in the distributed generation system. Currently, Single-Phase Transformerless Grid-Connected Photovoltaic (SPTG-CPV) inverters (1–10 kW) are undergoing further developments, with new designs, and interest of the solar market. In comparison to the transformer (TR) Galvanic Isolation (GI)-based inverters, its advantageous features are lower cost, lighter weight, smaller volume, higher efficiency, and less complexity. In this paper, a review of SPTG-CPV inverters has been carried out. The basic operational principles of all SPTG-CPV inverters are presented in details for positive, negative, and zero cycles. A comprehensive analysis of each topology has been deliberated. A comparative assessment is also performed based on weaknesses, strengths, component ratings, efficiency, total harmonic distortion (THD), semiconductor device losses, and leakage current of various SPTG-CPV inverters schemes. Typical PV inverter structures and control schemes for grid connected three-phase system and single-phase systems are also discussed, described, and reviewed. Comparison of various industrial grids-connected PV inverters is also performed. Loss analysis is also performed for various topologies at 1 kW. Selection of appropriate topologies for their particular application is thoroughly presented. Then, discussion and forthcoming progress are emphasized. Lastly, the conclusions are presented. More than 100 research publications on the topic of SPTG-CPV inverter topologies, configurations, and control schematics along with the recent developments are thoroughly reviewed and classified for quick reference.

Description: Energies, Vol. 11, Pages 1964: Lightning Impulse Withstand of Natural Ester Liquid Energies doi: 10.3390/en11081964 Authors: Stephanie Haegele Farzaneh Vahidi Stefan Tenbohlen Kevin J. Rapp Alan Sbravati Due to the low biodegradability of mineral oil, intense research is conducted to define alternative liquids with comparable dielectric properties. Natural ester liquids are an alternative in focus; they are used increasingly as insulating liquid in distribution and power transformers. The main advantages of natural ester liquids compared to mineral oil are their good biodegradability and mainly high flash and fire points providing better fire safety. The dielectric strength of natural ester liquids is comparable to conventional mineral oil for homogeneous field arrangements. However, many studies showed a reduced dielectric strength for highly inhomogeneous field arrangements. This study investigates at which degree of inhomogeneity differences in breakdown voltage between the two insulating liquids occur. Investigations use lightning impulses with different electrode arrangements representing different field inhomogeneity factors and different gap distances. To ensure comparisons with existing transformer geometries, investigations are application-oriented using a transformer conductor model, which is compared to other studies. Results show significant differences in breakdown voltage from an inhomogeneity factor of 0.1 (highly inhomogeneous field) depending on the gap distance. Larger electrode gaps provide a larger inhomogeneity at which differences in breakdown voltages occur.

Description: Energies, Vol. 11, Pages 1963: Numerical Analysis to Determine Reliable One-Diode Model Parameters for Perovskite Solar Cells Energies doi: 10.3390/en11081963 Authors: Esteban Velilla Juan Bernardo Cano Keony Jimenez Jaime Valencia Daniel Ramirez Franklin Jaramillo With the aim to determine the photo-generated current, diode saturation current, ideality factor, shunt, and series resistances related to the one-diode model for p-i-n planar perovskite solar cells, reference cells with active area of approximately 1 cm2 and efficiencies ranging between 4.6 and 12.2% were fabricated and characterized at standard test conditions. To estimated feasible parameters, the mean square error between the I-V curve data of these cells and the circuital model results were minimized using a Genetic Algorithm combined with the Nelder-Mead method. When considering the optimization process solutions, a numerical sensitivity analysis of the error as a function of the estimated parameters was carried out. Based on the errors behavior that is showed graphically through maps, it was demonstrated that the set of parameters estimated for each cell were reliable, meaningful, and realistic, and being related to errors lower than 9.1 × 10−9. Therefore, these results can be considered as global solutions of the optimization process. Moreover, based on the lower errors obtained from the optimization process, it was possible to affirm that the one-diode model is suitable to model the I-V curve of perovskite solar cells. Finally, the estimated parameters suggested that the average ideality factor is close to 2 when the fill factor of the I-V curves is higher than 0.5. Lower fill factors corresponded to ideality that was higher than 3, linked to lower efficiencies, and high loses effects reflected on lower shunt resistances. Lower ideality factor of 1.4 corresponds to the best performing solar cells.

Description: Energies, Vol. 11, Pages 1962: Energy Loss Allocation in Smart Distribution Systems with Electric Vehicle Integration Energies doi: 10.3390/en11081962 Authors: Paulo M. De Oliveira-De Jesus Mario A. Rios Gustavo A. Ramos This paper presents a three-phase loss allocation procedure for distribution networks. The key contribution of the paper is the computation of specific marginal loss coefficients (MLCs) per bus and per phase expressly considering non-linear load models for Electric Vehicles (EV). The method was applied in a unbalanced 12.47 kV feeder with 12,780 households and 1000 EVs under peak and off-peak load conditions. Results obtained were also compared with the traditional roll-in embedded allocation procedure (pro rata) using non-linear and standard constant power models. Results show the influence of the non-linear load model in the energy losses allocated. This result highlights the importance of considering an appropriate EV load model to appraise the overall losses encouraging the use and further development of the methodology

Description: Entropy, Vol. 20, Pages 564: A New Fractional-Order Chaotic System with Different Families of Hidden and Self-Excited Attractors Entropy doi: 10.3390/e20080564 Authors: Jesus Munoz-Pacheco Ernesto Zambrano-Serrano Christos Volos Sajad Jafari Jacques Kengne Karthikeyan Rajagopal In this work, a new fractional-order chaotic system with a single parameter and four nonlinearities is introduced. One striking feature is that by varying the system parameter, the fractional-order system generates several complex dynamics: self-excited attractors, hidden attractors, and the coexistence of hidden attractors. In the family of self-excited chaotic attractors, the system has four spiral-saddle-type equilibrium points, or two nonhyperbolic equilibria. Besides, for a certain value of the parameter, a fractional-order no-equilibrium system is obtained. This no-equilibrium system presents a hidden chaotic attractor with a `hurricane’-like shape in the phase space. Multistability is also observed, since a hidden chaotic attractor coexists with a periodic one. The chaos generation in the new fractional-order system is demonstrated by the Lyapunov exponents method and equilibrium stability. Moreover, the complexity of the self-excited and hidden chaotic attractors is analyzed by computing their spectral entropy and Brownian-like motions. Finally, a pseudo-random number generator is designed using the hidden dynamics.

Description: Entropy, Vol. 20, Pages 561: Statistical Significance of Earth’s Electric and Magnetic Field Variations Preceding Earthquakes in Greece and Japan Revisited Entropy doi: 10.3390/e20080561 Authors: Nicholas Sarlis By analyzing the seismicity in a new time domain, termed natural time, we recently found that the change of the entropy under time reversal (Physica A2018, 506, 625–634) and the relevant complexity measures (Entropy2018, 20, 477) exhibit pronounced variations before the occurrence of the M8.2 earthquake in Mexico on 7 September 2017. Here, the statistical significance of precursory phenomena associated with other physical properties and in particular the anomalous variations observed in the Earth’s electric and magnetic fields before earthquakes in different regions of the world and in particular in Greece since 1980s and Japan during 2001–2010 are revisited (the latter, i.e., the magnetic field variations are alternatively termed ultra low frequency (ULF) seismo-magnetic phenomena). Along these lines we employ modern statistical tools like the event coincidence analysis and the receiver operating characteristics technique. We find that these precursory variations are far beyond chance and in addition their lead times fully agree with the experimental findings in Greece since the 1980s.

Description: Entropy, Vol. 20, Pages 563: A New Underwater Acoustic Signal Denoising Technique Based on CEEMDAN, Mutual Information, Permutation Entropy, and Wavelet Threshold Denoising Entropy doi: 10.3390/e20080563 Authors: Yuxing Li Yaan Li Xiao Chen Jing Yu Hong Yang Long Wang Owing to the complexity of the ocean background noise, underwater acoustic signal denoising is one of the hotspot problems in the field of underwater acoustic signal processing. In this paper, we propose a new technique for underwater acoustic signal denoising based on complete ensemble empirical mode decomposition with adaptive noise (CEEMDAN), mutual information (MI), permutation entropy (PE), and wavelet threshold denoising. CEEMDAN is an improved algorithm of empirical mode decomposition (EMD) and ensemble EMD (EEMD). First, CEEMDAN is employed to decompose noisy signals into many intrinsic mode functions (IMFs). IMFs can be divided into three parts: noise IMFs, noise-dominant IMFs, and real IMFs. Then, the noise IMFs can be identified on the basis of MIs of adjacent IMFs; the other two parts of IMFs can be distinguished based on the values of PE. Finally, noise IMFs were removed, and wavelet threshold denoising is applied to noise-dominant IMFs; we can obtain the final denoised signal by combining real IMFs and denoised noise-dominant IMFs. Simulation experiments were conducted by using simulated data, chaotic signals, and real underwater acoustic signals; the proposed denoising technique performs better than other existing denoising techniques, which is beneficial to the feature extraction of underwater acoustic signal.

Description: Geosciences, Vol. 8, Pages 279: Detection of Stones in Marine Habitats Combining Simultaneous Hydroacoustic Surveys Geosciences doi: 10.3390/geosciences8080279 Authors: Svenja Papenmeier H. Christian Hass Exposed stones in sandy sublittoral environments are hotspots for marine biodiversity, especially for benthic communities. The detection of single stones is principally possible using sidescan-sonar (SSS) backscatter data. The data resolution has to be high to visualize the acoustic shadows of the stones. Otherwise, stony substrates will not be differentiable from other high backscatter substrates (e.g., gravel). Acquiring adequate sonar data and identifying stones in backscatter images is time consuming because it usually requires visual-manual procedures. To develop a more efficient identification and demarcation procedure of stone fields, sidescan sonar and parametric echo sound data were recorded within the marine protected area of “Sylt Outer Reef” (German Bight, North Sea). The investigated area (~5.900 km2) is characterized by dispersed heterogeneous moraine and marine deposits. Data from parametric sediment echo sounder indicate hyperbolas at the sediment surface in stony areas, which can easily be exported. By combining simultaneous recorded low backscatter data and parametric single beam data, stony grounds were demarcated faster, less complex and reproducible from gravelly substrates indicating similar high backscatter in the SSS data.

Description: IJERPH, Vol. 15, Pages 1605: An Analysis of Reported Dangerous Incidents, Exposures, and Near Misses amongst Army Soldiers International Journal of Environmental Research and Public Health doi: 10.3390/ijerph15081605 Authors: Ben Schram Robin Orr Timothy Rigby Rodney Pope Occupational health and safety incidents occurring in the military context are of great concern to personnel and commanders. Incidents such as “dangerous incidents”, “exposures”, and “near misses” (as distinct from injuries, illnesses, and fatalities) indicate serious health and safety risks faced by military personnel, even if they do not cause immediate harm. These risks may give rise to harm in the future, if not adequately addressed, and in some cases the incidents may cause latent harm. The purpose of this study was to ascertain the rates and patterns of incidents of these types reported by full time (ARA) and part time (ARES) Australian Army personnel. A retrospective cohort study was performed using self-reported incident data from the Workplace Health, Safety, Compensation and Reporting (WHSCAR) database over a two-year period. Data were analysed descriptively. Of 3791 such incidents, 3636 (96 percent) occurred in ARA and 155 (4 percent) in ARES personnel, somewhat consistent with the proportions of total army person-years served in each (ARA 93 percent; ARES 7 percent). In ARA, 84 percent of these incident types were exposures, 14 percent near misses, and 2 percent dangerous incidents. In ARES, 55 percent of incidents were exposures, 38 percent near misses, and 7 percent dangerous incidents. Soldiers at the rank of ‘private’ experienced the highest rates of these incident types, in both ARA and ARES. Driving gave rise to more near misses than any other activity, in both populations. Exposures to chemicals and sounds were more common in the ARA than ARES. The ARES reported higher proportions of vehicle near misses and multiple mechanism dangerous incidents than the ARA. The findings of this study can usefully inform development of risk mitigation strategies for dangerous incidents, exposures, and near misses in army personnel.

Description: IJERPH, Vol. 15, Pages 1604: Chronic Disease, Disability, Psychological Distress and Suicide Ideation among Rural Elderly: Results from a Population Survey in Shandong International Journal of Environmental Research and Public Health doi: 10.3390/ijerph15081604 Authors: Jing Zhu Lingzhong Xu Long Sun Jiajia Li Wenzhe Qin Gan Ding Qian Wang Jiao Zhang Su Xie Zihang Yu Objective: Suicide is a major public health and social problem in contemporary societies. Previous studies showed that the older the seniors were, the more likely it was that they would experience disability, chronic disease, or both. The objective of this study was to examine the joint effects of chronic disease and physical disability on suicide ideation while controlling for psychological distress among the rural elderly living in Shandong Province, China. Method: A total of 5514 rural elderly individuals (60+) living in Shandong Province, China were included in this study. Suicidal ideation was assessed by using questions from the National Comorbidity Survey (NCS). Multiple logistic analyses were performed to examine the factors associated with suicide ideation. A path analysis was conducted to test the direct and indirect effects of chronic disease and of activity of daily living (ADL) limitation on suicide ideation while controlling for psychological distress. Results: The prevalence of suicide ideation among the rural elderly in Shandong, China was 11.0%. Psychological distress had the strongest direct (β = 0.392) and total effect (β = 0.392), chronic disease (β = −0.034; β = −0.063) had both direct and indirect impacts, and ADL (β = 0.091) had indirect impacts on suicide ideation. Psychological distress was a mediator between chronic disease, ADL limitation, and suicide ideation. Conclusions: Psychological distress was the greatest influencing factor of suicide ideation among the rural elderly, followed by chronic disease and disability. Effective intervention measures should be taken to facilitate the early detection of psychological distress in clinical practice among the rural elderly.

Description: IJERPH, Vol. 15, Pages 1601: Risk of Appendicitis among Children with Different Piped Water Supply: A Nationwide Population-Based Study International Journal of Environmental Research and Public Health doi: 10.3390/ijerph15081601 Authors: Hao-Ming Li Shi-Zuo Liu Ying-Kai Huang Yuan-Chih Su Chia-Hung Kao Appendicitis is a common surgical condition for children. However, environmental effects, such as piped water supply, on pediatric appendicitis risk remain unclear. This longitudinal, nationwide, cohort study aimed to compare the risk of appendicitis among children with different levels of piped water supply. Using data from Taiwan Water Resource Agency and National Health Insurance Research Database, we identified 119,128 children born in 1996–2010 from areas of the lowest piped water supply (prevalence 51.21% to 63.06%) as the study cohort; additional 119,128 children of the same period in areas of the highest piped water supply (prevalence 98.97% to 99.63%) were selected as the controls. Both cohorts were propensity-score matched by baseline variables. We calculated the hazard ratios (HRs) and 95% confidence intervals (CIs) of appendicitis in the study cohort compared to the controls by Cox proportional hazards regression. The study cohort had a raised overall incidence rates of appendicitis compared to the control cohort (12.8 vs. 8.7 per 10,000 person-years). After covariate adjustment, the risk of appendicitis was significantly increased in the study cohort (adjusted HR = 1.46, 95% CI: 1.35, 1.58, p < 0.001). Subgroup and sensitivity analyses showed consistent results that children with low piped water supply had a higher risk of appendicitis than those with high piped water supply. This study demonstrated that children with low piped water supply were at an increased risk of appendicitis. Enhancement of piped water availability in areas lacking adequate, secure, and sanitized water supply may protect children against appendicitis.

Description: IJERPH, Vol. 15, Pages 1600: Alternative Risk Assessment for Dangerous Chemicals in South Korea Regulation: Comparing Three Modeling Programs International Journal of Environmental Research and Public Health doi: 10.3390/ijerph15081600 Authors: Hyo Eun Lee Jong-Ryeul Sohn Sang-Hoon Byeon Seok J. Yoon Kyong Whan Moon Unlike other countries, the Korean chemical industry does not clearly distinguish between industrial sites and residential areas. The 2012 Gumi Hydrogen Fluoride Accident revealed that chemical accidents could cause damage to nearby residents. Accordingly, the Chemicals Control Act was enacted in 2015, which requested industrial sites using chemicals to perform a risk assessment for all chemical facilities and to distribute the results to the local residents and governments. Industrial businesses had the responsibility of warning the local residents. In this study, two programs (Areal Location of Hazardous Atmospheres (ALOHA), Process Hazard Analysis Software Tool (PHAST)) were compared with Korea Off-site Risk Assessment Supporting Tool (KORA), which is the current representative risk assessment program used in Korea Chemicals Control Act. The five chemical substances (nitric acid, hydrogen chloride, ammonia, sulfuric acid, and formaldehyde) most commonly involved in chemical accidents were selected. The range of influence of ERPG-2 (Emergency Response Planning Guideline) on chemical accidents was modeled and the results compared. ALOHA was found to be the most suitable program for the determination of toxicity for nitrate acid and ammonia, KORA for hydrogen chloride and sulfuric acid, and PHAST for formaldehyde. To maximize the safety of many local residents and to prepare for chemical accidents, risk assessments should be conducted using a variety of risk assessment programs, and the worst-case damage radius should be determined.

Description: Materials, Vol. 11, Pages 1308: Observation of Morphology Changes of Fine Eutectic Si Phase in Al-10%Si Cast Alloy during Heat Treatment by Synchrotron Radiation Nanotomography Materials doi: 10.3390/ma11081308 Authors: Shougo Furuta Masakazu Kobayashi Kentaro Uesugi Akihisa Takeuchi Tomoya Aoba Hiromi Miura A series of three-dimensional morphology changes of fine eutectic Si-particles during heat treatment have been investigated in Self-modified and Sr-modified Al-10%Si cast alloys by means of synchrotron radiation nanotomography utilizing a Fresnel zone plate and a Zernike phase plate in this study. The coral-like shape particles observed in Sr-modified cast alloy fragmented at branch and neck during heat treatment at 773 K. The fragmentation occurred up to 900 s. After that, the fragmented particles grew and spheroidized by Ostwald ripening. On the other hand, rod-like shaped eutectic Si-particles observed in self-modified cast alloy were larger in size compared with the particle size in Sr-modified cast alloy. Separation of eutectic Si-particles in Self-modified cast alloy occurred up to approximately 900 s, which was similar tendency to that in Sr-modified cast alloy. However, it was found that the morphology change behavior was very complex in rod-like shape Si-particles. The three-dimensional morphology changes of fine eutectic Si-particles in both cast alloys, specifically fragmentation and spheroidizing, can be connected to changes in mechanical properties.

Description: Materials, Vol. 11, Pages 1306: Pattern-Dependent Mammalian Cell (Vero) Morphology on Tantalum/Silicon Oxide 3D Nanocomposites Materials doi: 10.3390/ma11081306 Authors: Hassan I. Moussa Megan Logan Wing Y. Chan Kingsley Wong Zheng Rao Marc G. Aucoin Ting Y. Tsui The primary goal of this work was to investigate the resulting morphology of a mammalian cell deposited on three-dimensional nanocomposites constructed of tantalum and silicon oxide. Vero cells were used as a model. The nanocomposite materials contained comb structures with equal-width trenches and lines. High-resolution scanning electron microscopy and fluorescence microscopy were used to image the alignment and elongation of cells. Cells were sensitive to the trench widths, and their observed behavior could be separated into three different regimes corresponding to different spreading mechanism. Cells on fine structures (trench widths of 0.21 to 0.5 μm) formed bridges across trench openings. On larger trenches (from 1 to 10 μm), cells formed a conformal layer matching the surface topographical features. When the trenches were larger than 10 μm, the majority of cells spread like those on blanket tantalum films; however, a significant proportion adhered to the trench sidewalls or bottom corner junctions. Pseudopodia extending from the bulk of the cell were readily observed in this work and a minimum effective diameter of ~50 nm was determined for stable adhesion to a tantalum surface. This sized structure is consistent with the ability of pseudopodia to accommodate ~4–6 integrin molecules.

Description: Materials, Vol. 11, Pages 1307: In Situ DRIFTS Studies of NH3-SCR Mechanism over V2O5-CeO2/TiO2-ZrO2 Catalysts for Selective Catalytic Reduction of NOx Materials doi: 10.3390/ma11081307 Authors: Yaping Zhang Xiupeng Yue Tianjiao Huang Kai Shen Bin Lu TiO2-ZrO2 (Ti-Zr) carrier was prepared by a co-precipitation method and 1 wt. % V2O5 and 0.2 CeO2 (the Mole ratio of Ce to Ti-Zr) was impregnated to obtain the V2O5-CeO2/TiO2-ZrO2 catalyst for the selective catalytic reduction of NOx by NH3. The transient activity tests and the in situ DRIFTS (diffuse reflectance infrared Fourier transform spectroscopy) analyses were employed to explore the NH3-SCR (selective catalytic reduction) mechanism systematically, and by designing various conditions of single or mixing feeding gas and pre-treatment ways, a possible pathway of NOx reduction was proposed. It was found that NH3 exhibited a competitive advantage over NO in its adsorption on the catalyst surface, and could form an active intermediate substance of -NH2. More acid sites and intermediate reaction species (-NH2), at lower temperatures, significantly promoted the SCR activity of the V2O5-0.2CeO2/TiO2-ZrO2 catalyst. The presence of O2 could promote the conversion of NO to NO2, while NO2 was easier to reduce. The co-existence of NH3 and O2 resulted in the NH3 adsorption strength being lower, as compared to tests without O2, since O2 could occupy a part of the active site. Due to CeO2’s excellent oxygen storage-release capacity, NH3 adsorption was weakened, in comparison to the 1 wt. % V2O5-0.2CeO2/TiO2-ZrO2 catalyst. If NOx were to be pre-adsorbed in the catalyst, the formation of nitrate and nitro species would be difficult to desorb, which would greatly hinder the SCR reaction. All the findings concluded that NH3-SCR worked mainly through the Eley-Rideal (E-R) mechanism.

Description: Sensors, Vol. 18, Pages 2450: Features of X-Band Radar Backscattering Simulation Based on the Ocean Environmental Parameters in China Offshore Seas Sensors doi: 10.3390/s18082450 Authors: Tao Wu Zhensen Wu Jiaji Wu Gwanggil Jeon Liwen Ma The X-band marine radar has been employed as a remote sensing tool for sea state monitoring. However, there are few literatures about sea spectra considering both the wave parameters and short wind-wave spectra in China Offshore Seas, which are of theoretical and practical significance. Based on the wave parameters acquired from the European Centre for Medium-Range Weather Forecasts reanalysis data (ERA-Interim reanalysis data) during 36 months from 2015 to 2017, a finite depth sea spectrum considering both wind speeds and ocean environmental parameters is established in this study. The wave spectrum is then built into a modified two-scale model, which can be related to the ocean environmental parameters (wind speeds and wave parameters). The final results are the mean backscattering coefficients over the variety of sea states at a given wind speed. As the model predicts, the monthly maximum backscattering coefficients in different seas change slowly (within 4 dB). In addition, the differences of the backscattering coefficients in different seas are quite small during azimuthal angles of 0° to 90° and 270° to 360° with a relative error within 1.5 dB at low wind speed (5 m/s) and 2 dB at high wind speed (10 m/s). With the method in the paper, a corrected result from the experiment can be achieved based on the relative error analysis in different conditions.

Description: Sustainability, Vol. 10, Pages 2659: Research on the Influence of Real Estate Development on Private Investment: A Case Study of China Sustainability doi: 10.3390/su10082659 Authors: Jiangtao Li Jianyue Ji Huiwen Guo Lei Chen Private investment in China, as a developing country, is an important source of financing for Chinese SMEs (Small and Medium-Size Enterprises) and has played a major role in the development of the real economy. However, in 2016, the growth rate of private investment in China dropped from 10.18% to 3.17%, which had a significant impact on the real economy. At the same time, China’s real estate market has developed rapidly, attracting a large number of capital inflows. The relationship between real estate development and private investment in China is worth considering. This study first, theoretically analyzes the influence mechanism of real estate industry on private investment, pointing out that within a modest development range, the development of real estate industry can promote private investment through the industrial linkage, urbanization, and balance sheet effects, but when real estate is overdeveloped, it has an inhibitory effect on private investment through vampire effect, raising costs and reducing demand effect. In other words, real estate has different effects on private investment in different developmental periods. Therefore, there is a non-linear relationship between the two variables. Second, the relevant provincial panel data of 31 provinces in mainland China from 2003 to 2015 were selected. Using the dynamic panel system Generalized Method of Moments (GMM), this study estimated the correlation between real estate development and private investment. The empirical results showed that the development of the real estate industry has a significant impact on the level of private investment; the two showing an “inverted U-shaped” relationship. At present, in some provinces in China, the real estate industry has exceeded the inverted U-shaped threshold. To boost the vitality of private investment in promoting real economic growth, the development of the real estate industry should be restricted, and house prices should be properly regulated.

Description: Sustainability, Vol. 10, Pages 2657: Numerical Thermal Characterization and Performance Metrics of Building Envelopes Containing Phase Change Materials for Energy-Efficient Buildings Sustainability doi: 10.3390/su10082657 Authors: Mingli Li Guoqing Gui Zhibin Lin Long Jiang Hong Pan Xingyu Wang Residential and commercial buildings consume nearly 40 percent of total USA energy use and account for one-third of total greenhouse gas emissions. The challenges are how to effectively promote energy efficiency in buildings to respond to the high financial burden of energy consumption, while reducing pollution. Phase change materials (PCMs) have been used as passive energy storage for building systems. Along this vein, this study aims to numerically elucidate the design parameters of building envelopes strengthened by PCM layers, and unveil their impacts on building energy efficiency. Critical design variables, such as the thickness of the PCM layer, the latent heat of PCMs, or melting temperature of PCMs were selected for a parametric study, while performance metrics were used to assess building efficiency. Results revealed that PCM-enabled building walls exhibited different levels of improvement, in terms of reduction of peak temperature and temperature swings. Among the variables, the selection of the proper melting point for a PCM was identified as the most crucial parameter for determining building energy efficiency, while the heat of fusion was also observed as a critical property of PCM for building potential. Findings also demonstrated that the placement of the PCM near the interior wall surface could achieve higher efficiency, as compared to other cases. Results also showed that the thermal conductivity of PCM has a minimum contribution to energy storage capacity.

Description: Sensors, Vol. 18, Pages 2451: Interaction of Lamb Wave Modes with Weak Material Nonlinearity: Generation of Symmetric Zero-Frequency Mode Sensors doi: 10.3390/s18082451 Authors: Xiaoqiang Sun Xiangyan Ding Feilong Li Shijie Zhou Yaolu Liu Ning Hu Zhongqing Su Youxuan Zhao Jun Zhang Mingxi Deng The symmetric zero-frequency mode induced by weak material nonlinearity during Lamb wave propagation is explored for the first time. We theoretically confirm that, unlike the second harmonic, phase-velocity matching is not required to generate the zero-frequency mode and its signal is stronger than those of the nonlinear harmonics conventionally used, for example, the second harmonic. Experimental and numerical verifications of this theoretical analysis are conducted for the primary S0 mode wave propagating in an aluminum plate. The existence of a symmetric zero-frequency mode is of great significance, probably triggering a revolutionary progress in the field of non-destructive evaluation and structural health monitoring of the early-stage material nonlinearity based on the ultrasonic Lamb waves.

Description: Sustainability, Vol. 10, Pages 2655: Substructure Hybrid Simulation Boundary Technique Based on Beam/Column Inflection Points Sustainability doi: 10.3390/su10082655 Authors: Zaixian Chen Xueyuan Yan Hao Wang Xingji Zhu Billie F. Spencer Compatibility among substructures is an issue for hybrid simulation. Traditionally, the structure model is regarded as the idealized shear model. The equilibrium and compatibility of the axial and rotational direction at the substructure boundary are neglected. To improve the traditional boundary technique, this paper presents a novel substructure hybrid simulation boundary technique based on beam/column inflection points, which can effectively avoid the complex operation for realizing the bending moment at the boundary by using the features of the inflection point where the bending moment need not be simulated in the physical substructure. An axial displacement prediction technique and the equivalent force control method are used to realize the proposed method. The numerical simulation test scheme for the different boundary techniques was designed to consider three factors: (i) the different structural layers; (ii) the line stiffness ratio of the beam to column; and (iii) the peak acceleration. The simulation results for a variety of numerical tests show that the proposed technique shows better performance than the traditional technique, demonstrating its potential in improving HS test accuracy. Finally, the accuracy and feasibility of the proposed boundary technique is verified experimentally through the substructure hybrid simulation tests of a six-story steel frame model.

Description: Minerals, Vol. 8, Pages 326: Hydrotalcite and Hydrocalumite in Mortar Binders from the Medieval Castle of Portilla (Álava, North Spain): Accurate Mineralogical Control to Achieve More Reliable Chronological Ages Minerals doi: 10.3390/min8080326 Authors: Graciela Ponce-Antón Luis Angel Ortega Maria Cruz Zuluaga Ainhoa Alonso-Olazabal Jose Luis Solaun Mortars from different stratigraphic units at Portilla Castle (Alava, North Spain) have been analyzed for mineralogical characterization before radiocarbon dating. The mortar binder at Portilla Castle is composed not only of neoformation calcite but also of double-layered hydroxide (LDH) minerals such as hydrotalcite and hydrocalumite. The mineralogy of several fractions of the binder has been analyzed to determine the granulometric distribution of minerals in the binder. The continuous monitoring of mineralogy during the extraction of different grain size fractions has been performed by using a scanning electron microscopy (SEM), X-ray diffraction (XRD), and thermogravimetric analyses (TGA). Hydrotalcite and hydrocalumite-bearing mortar binders give older ages than expected since they introduce dead carbon into the system.

Description: Atmosphere, Vol. 9, Pages 299: The Effect of Nonlocal Vehicle Restriction Policy on Air Quality in Shanghai Atmosphere doi: 10.3390/atmos9080299 Authors: Junjie Li Xiao-Bing Li Bai Li Zhong-Ren Peng In recent years, road space rationing policies have been increasingly applied as a traffic management solution to tackle congestion and traffic emission problems in big cities. Existing studies on the effect of traffic policy on air quality have mainly focused on the odd–even day traffic restriction policy or one-day-per-week restriction policy. There are few studies paying attention to the effect of nonlocal license plate restrictions on air quality in Shanghai. Restrictions toward nonlocal vehicles usually prohibit vehicles with nonlocal license plates from entering certain urban areas or using certain subsets of the road network (e.g., the elevated expressway) during specific time periods on workdays. To investigate the impact of such a policy on the residents’ exposure to pollutants, CO concentration and Air Quality Index (AQI) were compared during January and February in 2015, 2016 and 2017. Regression discontinuity (RD) was used to test the validity of nonlocal vehicle restriction on mitigating environmental pollution. Several conclusions can be made: (1) CO concentration was higher on ground-level roads on the restriction days than those in the nonrestriction days; (2) the extension of the restriction period exposed the commuters to high pollution for a longer time on the ground, which will do harm to them; and (3) the nonlocal vehicle restriction policy did play a role in improving the air quality in Shanghai when extending the evening rush period. Additionally, some suggestions are mentioned in order to improve air quality and passenger health and safety.

Description: Atmosphere, Vol. 9, Pages 297: Sources Profiles of Volatile Organic Compounds (VOCs) Measured in a Typical Industrial Process in Wuhan, Central China Atmosphere doi: 10.3390/atmos9080297 Authors: Longjiao Shen Ping Xiang Shengwen Liang Wentai Chen Ming Wang Sihua Lu Zuwu Wang Industrial emission is an important source of ambient volatile organic compounds (VOCs) in Wuhan City, Hubei Province, China. We collected 53 VOC samples from petrochemical, surface coating, electronic manufacturing, and gasoline evaporation using stainless canisters to develop localized source profiles. Concentrations of 86 VOC species, including hydrocarbons, halocarbons, and oxygenated VOCs, were quantified by a gas chromatography–flame ionization detection/mass spectrometry system. Alkanes were the major constituents observed in the source profile from the petrochemical industry. Aromatics (79.5~81.4%) were the largest group in auto-painting factories, while oxygenated VOCs (82.0%) and heavy alkanes (68.7%) were dominant in gravure printing and offset printing factories, respectively. Acetone was the largest contributor and the most frequently monitored species in printed circuit board (PCB) manufacturing, while VOC species emitted from integrated chip (IC) were characterized by high contents of isopropanol (56.4–98.3%) and acetone (30.8%). Chemical compositions from vapor of gasoline 92#, 93#, and 98# were almost identical. Alkanes were the dominant VOC group, with i-pentane being the most abundant species (31.4–37.7%), followed by n-butane and n-pentane. However, high loadings of heavier alkanes were observed in the profile of diesel evaporation.

Description: Atmosphere, Vol. 9, Pages 298: Chemical Composition and Sources of Marine Aerosol over the Western North Pacific Ocean in Winter Atmosphere doi: 10.3390/atmos9080298 Authors: Hong-Wei Xiao Hua-Yun Xiao Chun-Yan Shen Zhong-Yi Zhang Ai-Min Long Atmospheric deposition of long-range transported continental substances from natural and anthropogenic sources affects biogeochemical processes in marine systems. Emissions of sea spray contribute aerosol particles to the marine atmosphere. Despite the importance of continental dispersion and atmospheric processes involving aerosol particles within remote marine atmosphere, knowledge of the sources of various water-soluble ions is limited because of insufficient observations. Concentrations of Total suspended particulates (TSPs) and major inorganic ions (Cl−, Na+, SO42−, Mg2+, Ca2+, K+, NO3−, NH4+), as well as organic nitrogen (ON-N) values, were measured in marine aerosol collected over the western north Pacific (WNP) during a cruise from 3 December 2014 to 13 March 2015. Aerosol samples were analyzed to determine their chemical characteristics and a source apportionment for this region and the continental influence on the open ocean when air masses are from continent in winter. TSP mass concentrations ranged from 14.1 to 136.0 μg/m3 with an average of 44.8 ± 28.1 μg/m3. Concentrations of TSPs and major ions were higher near the coast (close to Qingdao and Xiamen) and lower over the open ocean. The total mass of inorganic ions and organic nitrogen accounted for 51.1% of the total TSP. Cl− had highest concentrations among the major inorganic ions, followed by SO42−, NO3−, Mg2+, Ca2+, K+, and NH4+, respectively. However, Cl− showed a deficit relative to Na+ in most samples, likely related to heterogeneous reactions within the marine atmosphere. Most SO42−, Mg2+, Ca2+, and K+ were from sea salt, while other major ions were from continental sources. The non-sea-salt (nss) fractions of Ca2+, Mg2+ and K+ were derived from continental crust, while nss-SO42− and NO3− were derived from anthropogenic sources. ON had several sources, including reactions of NOx with volatile organic compounds (anthropogenic sources) or NH3 with gaseous hydrocarbons, as well as crustal and marine biogenic sources.

Description: Sustainability, Vol. 10, Pages 2666: Understanding the Spontaneous Spreading of Stone Bunds in Ethiopia: Implications for Sustainable Land Management Sustainability doi: 10.3390/su10082666 Authors: Meskerem Abi Aad Kessler Peter Oosterveer Degefa Tolossa This study deals with the spontaneous spreading of stone bunds in the central Ethiopian highlands, i.e., the adoption and implementation of stone bunds by farmers on their own initiative. The study tests the hypothesis that spontaneously implemented stone bunds, as compared to stone bunds implemented by mass mobilization campaigns, are more integrated with other land management practices and lead to higher yields. Data are collected in the Girar Jarso woreda through field observations and household surveys. Descriptive statistics are used to analyze and test the data at 1% and 5% probability levels. Results show that stone bunds are spontaneously implemented mainly on farmlands located nearby the homesteads where farmers perceive severe erosion, poor soil fertility and steep slope gradients. Compared to stone bunds implemented by mass mobilization, spontaneously implemented stone bunds are perceived as better maintained, more frequently modified to fit the farming system and better integrated with soil fertility management practices, such as applying fertilizer, compost and manure. Particularly, this better integration with other practices is very important, because it makes stone bunds more effective in reducing erosion, leading to beneficial effects on soil moisture and soil productivity, as perceived by farmers. The study, therefore, suggests that the mass mobilization campaign should use a more participatory and integrated approach, in which there is ample space for awareness raising and learning concerning the benefits of integrated farm management, and in which farmers themselves have a leading role in the decision on where to construct stone bunds. Such a strategy will lead to more sustainable impact on soil fertility and food security than the current top-down intervention approach.

Description: Forests, Vol. 9, Pages 464: Payment for Targeted Grazing: Integrating Local Shepherds into Wildfire Prevention Forests doi: 10.3390/f9080464 Authors: Elsa Varela Elena Górriz-Mifsud Jabier Ruiz-Mirazo Feliu López-i-Gelats Wildfires are one of the most prominent risks for Mediterranean forests, reducing the flow of ecosystem services and representing a hazard for infrastructure and human lives. Several wildfire prevention programs in southern Europe are currently incorporating extensive livestock grazers in fire prevention activities to reduce the high costs of mechanical clearance. Among these the Andalusian network of grazed fuel breaks, the so-called RAPCA program, stands out for its dimension and stability over time. RAPCA currently works with 220 local shepherds who, with their guided flocks maintain low biomass levels in almost 6000 ha of fuel breaks in public forests to meet fire prevention standards. This work analyses the institutional design and performance of the RAPCA payment scheme under a payment for environmental services (PES) framework. Results show effectiveness of the payment scheme while efficiency is achieved through savings relative to the mainstream mechanized biomass removal, as well as through reduced information asymmetry. High-level and stable political commitment has been crucial for the emergence and consolidation of RAPCA. Moreover, key intermediaries and sound monitoring practices increased levels of trust amongst involved actors. Beneficial side-effects include social recognition of shepherds’ activities and reduction of their friction with forest managers.

Description: Energies, Vol. 11, Pages 1970: Increase in Robustness against Effects of Coil Misalignment on Electrical Parameters Using Magnetic Material Layer in Planar Coils of Wireless Power Transfer Transformer Energies doi: 10.3390/en11081970 Authors: Joao Victor Pinon Pereira Dias Masafumi Miyatake Utilization of wireless power transfer in light rail transits is seen as one solution for electrification of lines. The main advantage of this supply system is the reduction of installation; moreover, the alignment between the transmitter coil in the track and the receiver coil in the train should be perfect in order not to affect the power transfer. To reduce the effects of misalignment on the input and output electric parameters of the system, a new planar core and coil design, called hybrid intercore coil, is proposed. The proposed design uses a magnetic material layer between the windings in the inner half of the coil to create a non-uniform magnetic field distribution, which makes the system more robust against the effects of coil misalignment on the system current and voltage. Simulations with finite element method software were conducted to compare designs. The results show that the proposed design is less susceptible to the effects of misalignment and is more efficient. Prototype cores were constructed to verify the simulation results. Measurements show a smaller input overcurrent and output overvoltage when operating in resonance mode. The proposed design reduced the effects of coil misalignment on electrical parameters.

Description: Energies, Vol. 11, Pages 1971: A New Lumped Parameter Model for Natural Gas Pipelines in State Space Energies doi: 10.3390/en11081971 Authors: Kai Wen Zijie Xia Weichao Yu Jing Gong Many algorithms and numerical methods, such as implicit and explicit finite differences and the method of characteristics, have been applied for transient flow in gas pipelines. From a computational point of view, the state space model is an effective method for solving complex transient problems in pipelines. However, the impulse output of the existing models is not the actual behavior of the pipeline. In this paper, a new lumped parameter model is proposed to describe the inertial nature of pipelines with inlet/outlet pressure and flow rate as outer variables in the state space. Starting from the basic mechanistic partial differential equations of the general one-dimensional compressible gas flow dynamics under isothermal conditions, the transfer functions are first acquired as the fundamental work. With Taylor-expansion and a transformation procedure, the inertia state space models are derived with proper simplification. Finally, three examples are used to illustrate the effectiveness of the proposed model. With the model, a real-time automatic scheduling scheme of the natural gas pipeline could be possible in the future.

Description: Energies, Vol. 11, Pages 1972: Comprehensive Design and Analysis of a State-Feedback Controller for a Dynamic Voltage Restorer Energies doi: 10.3390/en11081972 Authors: Javier Roldán-Pérez Aurelio García-Cerrada Alberto Rodríguez-Cabero Juan Luis Zamora-Macho Voltage sags result in unwanted operation stops and large economical losses in industrial applications. A dynamic voltage restorer (DVR) is a power-electronics-based device conceived to protect high-power installations against these events. However, the design of a DVR control system is not straightforward and it has some peculiarities. First of all, a DVR includes a resonant (LC) connection filter with a lightly damped resonance. Secondly, the control system of a DVR should work properly regardless of the type of load, which can be linear or non-linear, to be protected. In this paper, a digital state-feedback (SF) controller for a DVR is proposed to address these issues. The design and features of the SF controller are studied in detail. Two pole-placement alternatives are discussed and the system robustness is tested under variations in the system parameters. Furthermore, implementation aspects such as discretization not commonly addressed in the literature are described. The controller is implemented in its incremental form. A decoupling system for the dq-axis dynamics that takes into account system delays and the load current is proposed and analytically studied. The proposed controller is compared with two other alternatives found in the literature: a Proportional-Integral-Differential (PID) controller and a cascade controller. The effect of the load connected downstream a DVR is also studied, revealing the potential of the SF controller to damp the resonance under light load conditions. All control system developments were tested in a 5 kVA prototype of a DVR connected to a configurable grid.

Description: Forests, Vol. 9, Pages 462: Preferences of Tourists for the Service Quality of Taichung Calligraphy Greenway in Taiwan Forests doi: 10.3390/f9080462 Authors: Wan-Yu Liu Ching Chung This study explores preferences for a set of attributes that characterize the recreational value of Calligraphy Greenway, the most notable greenbelt in Taichung City, Taiwan. As an urban green space, the Calligraphy Greenway has its own recreational attributes and visitors’ preferences. This study uses the choice experiment method to determine visitors’ preference levels for five major attributes to improve the recreational quality. On average, each visitor visited there 9.15 times in the past year and spent 2.37 h per visit. Of the five recreational attributes, satisfaction with recreational activity opportunities had the highest score and satisfaction with cultural landscape resources had the lowest score. The importance is ranked in the order of recreational service quality, total recreational cost, environmental landscape resources, cultural landscape resources and recreational activity opportunities. Considering difference of groups, female visitors were more concerned with cost and activities but male visitors were more concerned with service quality and natural/cultural landscape resources. Local visitors were more concerned with cost and activities but non-local visitors were more concerned with environmental/cultural landscape resources. Both were concerned with service quality. Based on the results, this study makes the following recommendations: cultural landscape resources and quality of recreational services and facilities should be improved and more complete interpretative educational guidance should be provided to increase visitors’ willingness to visit. Additionally, it is suggested to set up various districts to cater for preferences of different visitor groups.

Description: Forests, Vol. 9, Pages 463: Implementing Participatory Processes in Forestry Training Using Social Network Analysis Techniques Forests doi: 10.3390/f9080463 Authors: Simone Blanc Federico Lingua Livio Bioglio Ruggero G. Pensa Filippo Brun Angela Mosso Public participation has become an important driver in increasing public acceptance of policy decisions, especially in the forestry sector, where conflicting interests among the actors are frequent. Stakeholder Analysis, complemented by Social Network Analysis techniques, was used to support the participatory process and to understand the complex relationships and the strong interactions among actors. This study identifies the forestry training sector stakeholders in the Western Italian Alps and describes their characteristics and priorities, in relation to training activities on entrepreneurial topics for forestry loggers. The hierarchy among actors has been identified, highlighting their respective roles and influence in decision-making processes. A lack of mutual communication among different and well-separated categories of actors has been identified, while good connections between stakeholders, operating in different territories, despite the presence of administrative and logistical barriers, have been observed. Training is a topic involving actors with different roles and interests. Nevertheless, all actors consider training about how to improve yields of forest operations and how to assess investments, particularly in innovative machinery, to be crucially important and conducive to a better comprehension of the wood supply chain and the enhancement of the raw material.

Description: Future Internet, Vol. 10, Pages 71: Hybrid Approach with Improved Genetic Algorithm and Simulated Annealing for Thesis Sampling Future Internet doi: 10.3390/fi10080071 Authors: Shardrom Johnson Jinwu Han Yuanchen Liu Li Chen Xinlin Wu Sampling inspection uses the sample characteristics to estimate that of the population, and it is an important method to describe the population, which has the features of low cost, strong applicability and high scientificity. This paper aims at the sampling inspection of the master’s degree thesis to ensure their quality, which is commonly estimated by random sampling. Since there are disadvantages in random sampling, a hybrid algorithm combined with an improved genetic algorithm and a simulated annealing algorithm is proposed in this paper. Furthermore, a novel mutation strategy is introduced according to the specialty of Shanghai’s thesis sampling to improve the efficiency of sampling inspection; the acceleration of convergence of the algorithm can also take advantage of this. The new algorithm features the traditional genetic algorithm, and it can obtain the global optimum in the optimization process and provide the fairest sampling plan under the constraint of multiple sampling indexes. The experimental results on the master’s thesis dataset of Shanghai show that the proposed algorithm well meets the requirements of the sampling inspection in Shanghai with a lower time-complexity.

Description: Future Internet, Vol. 10, Pages 70: Multidiscipline Integrated Platform Based on Probabilistic Analysis for Manufacturing Engineering Processes Future Internet doi: 10.3390/fi10080070 Authors: Lijun Zhang Kai Liu Jian Liu Researchers from different disciplines, such as materials science, computer science, safety science, mechanical engineering and controlling engineering, have aimed to improve the quality of manufacturing engineering processes. Considering the requirements of research and development of advanced materials, reliable manufacturing and collaborative innovation, a multidiscipline integrated platform framework based on probabilistic analysis for manufacturing engineering processes is proposed. The proposed platform consists of three logical layers: The requirement layer, the database layer and the application layer. The platform is intended to be a scalable system to gradually supplement related data, models and approaches. The main key technologies of the platform, encapsulation methods, information fusion approaches and the collaborative mechanism are also discussed. The proposed platform will also be gradually improved in the future. In order to exchange information for manufacturing engineering processes, scientists and engineers of different institutes of materials science and manufacturing engineering should strengthen their cooperation.

Description: Entropy, Vol. 20, Pages 567: Nonlocality in Bell’s Theorem, in Bohm’s Theory, and in Many Interacting Worlds Theorising Entropy doi: 10.3390/e20080567 Authors: Mojtaba Ghadimi Michael J. W. Hall Howard M. Wiseman “Locality” is a fraught word, even within the restricted context of Bell’s theorem. As one of us has argued elsewhere, that is partly because Bell himself used the word with different meanings at different stages in his career. The original, weaker, meaning for locality was in his 1964 theorem: that the choice of setting by one party could never affect the outcome of a measurement performed by a distant second party. The epitome of a quantum theory violating this weak notion of locality (and hence exhibiting a strong form of nonlocality) is Bohmian mechanics. Recently, a new approach to quantum mechanics, inspired by Bohmian mechanics, has been proposed: Many Interacting Worlds. While it is conceptually clear how the interaction between worlds can enable this strong nonlocality, technical problems in the theory have thus far prevented a proof by simulation. Here we report significant progress in tackling one of the most basic difficulties that needs to be overcome: correctly modelling wavefunctions with nodes.

Description: Forests, Vol. 9, Pages 461: A Review on the Dynamics of Prescribed Fire, Tree Mortality, and Injury in Managing Oak Natural Communities to Minimize Economic Loss in North America Forests doi: 10.3390/f9080461 Authors: Daniel C. Dey Callie Jo Schweitzer The long history of fire in North America spans millennia and is recognized as an important driver in the widespread and long-term dominance of oak species and oak natural communities. Frequent wildfires from about 1850 to 1950 resulted in much forest damage, and gained fire a negative reputation. The lack of fire for the past nearly 100 years due to suppression programs is now indicted as a major cause of widespread oak regeneration failures and loss of fire-dependent natural communities. The use of prescribed fire is increasing in forest management and ecosystem restoration. An understanding of fire effects on trees can provide the basis for the silviculture of restoring and sustaining oak ecosystems. We present an overview of fire-tree wounding interactions, highlight important determinants of fire injury and damage, and discuss several practical situations where fire can be used to favor oak while minimizing damage and devaluation of the forest. We also identify stages in stand development, regeneration methods, and management objectives for which fire has the potential of causing substantial damage and recommend preferred alternative practices.

Description: IJERPH, Vol. 15, Pages 1611: Immunohistochemical Evaluation of Peri-Implant Soft Tissues around Machined and Direct Metal Laser Sintered (DMLS) Healing Abutments in Humans International Journal of Environmental Research and Public Health doi: 10.3390/ijerph15081611 Authors: Carlo Mangano Francesco Guido Mangano Jamil Awad Shibli Leandro Amadeu Roth Gianmaria d’ Addazio Adriano Piattelli Giovanna Iezzi Background: Direct metal laser Sintering (DMLS) is an additive manufacturing technique that allows fabrication of dental implants and related components with a highly porous surface. To date, no human studies have investigated the soft tissue adhesion and presence of inflammatory infiltrate with porous DMLS healing abutments (HAs), nor have they compared these with the classic machined ones. Purpose: To evaluate the degree of cell adhesion (integrin expression) and the quantity/quality of inflammatory infiltrate, on HAs with different surfaces; full DMLS, full machined, and hybrid (half DMLS and half machined). Methods: Fifty implant patients were randomly assigned to receive one of these different Has: T1, full DMLS (11 subjects); T2, machined in the upper portion and DMLS in the lower one (10 subjects); T3, DMLS in the upper portion and machined in the lower one (19 subjects); T4, full machined (10 patients). Thirty days after placement, circular sections of soft tissues around HAs were retrieved for immunohistochemical evaluation. Results: With regard to the adhesion molecules, the samples showed different intensity of integrin expression, with a statistically significant difference (p < 0.001) between T1 and the other groups. All the samples were positive for the different clusters related to the inflammatory infiltrate (T lymphocytes, CD3; B lymphocytes, CD20; and macrophages, CD68), but a lower infiltrate was found in T1, with statistically significant differences (p < 0.001) among the groups. Conclusions: The HA surface seems to influence the degree of cell adhesion and the inflammatory infiltrate of the surrounding soft tissues.

Description: IJERPH, Vol. 15, Pages 1614: Effects of Bisphenol A and 4-tert-Octylphenol on Embryo Implantation Failure in Mouse International Journal of Environmental Research and Public Health doi: 10.3390/ijerph15081614 Authors: Dinh Nam Tran Eui-Man Jung Changhwan Ahn Jae-Hwan Lee Yeong-Min Yoo Eui-Bae Jeung Miscarriage due to blastocyst implantation failure occurs in up to two-thirds of all human miscarriage cases. Calcium ion has been shown to be involved in many cellular signal transduction pathways as well as in the regulation of cell adhesion, which is necessary for the embryo implantation process. Exposure to endocrine-disrupting chemicals (EDs) during early gestation results in disruption of intrauterine implantation and uterine reception, leading to implantation failure. In this study, ovarian estrogen (E2), bisphenol A (BPA), or 4-tert-octylphenol (OP), with or without ICI 182,780 (ICI) were injected subcutaneously from gestation day 1 to gestation day 3 post-coitus. The expression levels of the calcium transport genes were assessed in maternal uteri and implantation sites. The number of implantation sites was significantly low in the OP group, and implantation sites were absent in the E2, ICI and EDs + ICI groups. There were different calcium transient transport channel expression levels in uterus and implantation site samples. The levels of TRPV5 and TRPV6 gene expression were significantly increased by EDs with/without ICI treatment in utero. Meanwhile, TRPV5 and TRPV6 gene expression were significantly lower in implantation sites samples. NCX1 and PMCA1 mRNA levels were significantly decreased by OP and BPA in the implantation site samples. Compared to vehicle treatment in the uterus, both the MUC1 mRNA and protein levels were markedly high in all but the BPA group. Taken together, these results suggest that both BPA and OP can impair embryo implantation through alteration of calcium transport gene expressions and by affecting uterine receptivity.

Description: IJERPH, Vol. 15, Pages 1609: A Comparison of Dependence across Different Types of Nicotine Containing Products and Coffee International Journal of Environmental Research and Public Health doi: 10.3390/ijerph15081609 Authors: Karl Fagerstrom Introduction: Few studies have compared the dependence to different tobacco and nicotine products. Even less is known about how it relates to dependence on other common drugs, e.g., caffeine. In this study degree of dependence was compared between snus, cigarettes, nicotine replacement (NR), electronic cigarettes and coffee. Methods: A random sample of Swedish citizens belonging to an internet panel were contacted from September to October 2017. The responders were asked among other related things about their use of snus, NR, traditional cigarette or e-cigarette use and coffee consumption. The indicators of dependence used were: (A) the Heavy Smoking Index, (B) The proportions that used within 30 min after raising in the morning, (C) rating the first use in the morning as the most important and (D) Stating that it would be very hard to give up entirely. Results: Significantly fewer coffee drinkers started use within 30 min of awakening compared with all other products. The first use of the day was found to be more important for snus users compared with other products. On HSI there was no difference between snus and cigarettes. Snus and cigarettes were rated as being more difficult to give up than NR and coffee. Conclusion: Dependence to traditional cigarettes and snus seem to be relatively similar while NR was rated lower and coffee lowest. Since the prevalence of caffeine use in all forms is so much more prevalent than nicotine there might be more persons in the society heavily dependent on caffeine. Implication: Tobacco products are likely more dependence forming than NR products and coffee although there might be more people dependent on caffeine. The addiction to coffee or caffeine is seldom discussed in the society probably because of the little or no harm it causes. Funding: The Snus Commission in Sweden (snuskommissionen) funded the data collection. No funding used for the analysis and writing of manuscript.