ALBERT

Description: The objectives of this program are as follows: modelling of dynamics of composite tubular space structure truss members; and utilization of ultrasonic waves as probes for material and defect characterization. This discussion is presented in viewgraph format.

Description: In the interest of aviation safety, NASA and the FAA are jointly conducting research to determine the applicability of airborne, coherent Doppler radar techniques to detect early microburst in wind shear conditions during aircraft takeoff and landing. Researchers have developed a computer model of the radar which predicts its response when viewing a simulated microburst against the simulated clutter background of an airport, the so-called radar microburst ground clutter model. Studies employing this model revealed that Doppler radar can accurately detect microburst ahead of the aircraft in time for pilot evasive response, but flight experiments will be required for complete performance evaluation of the system. An experimental X band radar is being developed for future flight experiments to verify the simulation modeling results. A description of the experimental radar, recording equipment, and its installation on the NASA 515 aircraft is presented. The flight experiments to be conducted are also described.

Description: A new technique is described for calibration of complex multipolarization SAR imagery. Scatterer reciprocity and lack of correlation between like- and cross-polarized radar echoes for natural targets are used to remove cross-polarized contamination in the radar data channels without the use of known ground targets. If known targets are available, all data channels can be calibrated relative to one another and absolutely as well. The method is verified with airborne SAR data.

Description: The SAR (synthetic-aperture radar) data-processing algorithm to be used for the Magellan mission is described. Radar system design, SAR data characteristics, and hardware (H/W) constraints, which are critical to the processing algorithm design, are highlighted. Data flow and the H/W architecture are given to show the real-time data processing capability. Simulation results obtained from processing the synthetic point-target echos are presented to demonstrate the performance of the processing algorithm.

Description: The analysis and low-power testing of a square multiflare horn designed for 1-megawatt CW operation is described. Design considerations for the five-port input section are discussed. The required aperture modes are determined from radiation pattern considerations, and analysis of the multiflare section is carried out using mode matching. Measurements demonstrate that a circularly symmetric beam is produced with relatively low sidelobes.

Description: The cross polarization characteristics of rectantular patch antennas are studied experimentally. Data are presented showing the dependence of the copolarization to cross-polarization ratio on the aspect ratio in both the E and H planes. Three substrate thicknesses are included and the variation with resonant frequency is examined.

Description: Synthesis of dual-shaped offset reflector antennas to control the exit aperture distribution of amplitude and phase has received considerable attention in recent years. For a given feed illumination and desired aperture field distribution, an exact formulation of the problem of simultaneously synthesizing the shapes of the sub and main reflectors was presented recently by Galindo-Israel et al. (1987) in terms of a set of nonlinear first-order differential equations. In this paper, a numerical approach to solving these equations is discussed which circumvents some of the difficulties encountered by Galindo-Israel et al., particularly for small values of theta.

Description: The technique described uses the radar return from natural targets and at least one trihedral corner reflector to calibrate compressed polarimetric radar data for relative amplitude, relative phase, absolute amplitude, and system crosstalk. The crosstalk method is based on the theoretical result that, for natural targets with azimuthal symmetry, the copolarized and cross-polarized components of the scattering matrix are uncorrelated. This method does not require any external calibration targets to be deployed. Since compressed data are used, it is necessary to model the transmitting and receiving systems as reciprocal. The method is used to estimate the crosstalk parameters of the NASA/JPL aircraft for different types of terrain and for two frequencies. For the C-band systems the crosstalk is less than -20 dB for all ranges in the images. The crosstalk of the L-band system is a function of range, however, and may be as poor as -10 dB in the near range, leading to a noticeable distortion of the polarization signatures.

Description: A technique for estimation of the Doppler centroid of an SAR in the presence of large uncertainty in antenna boresight pointing is described. Also investigated is the image degradation resulting from data processing that uses an ambiguous centroid. Two approaches for resolving ambiguities in Doppler centroid estimation (DCE) are presented: the range cross-correlation technique and the multiple-PRF (pulse repetition frequency) technique. Because other design factors control the PRF selection for SAR, a generalized algorithm is derived for PRFs not containing a common divisor. An example using the SIR-C parameters illustrates that this algorithm is capable of resolving the C-band DCE ambiguities for antenna pointing uncertainties of about 2-3 deg.

Description: A theoretical analysis of polarization filtering for the bistatic case is developed for optimum discrimination between two types of targets. The resulting method is half analytical and half numerical. Because it is based on the Stokes matrix representation, the targets of interest can be extended targets. The scattered field from such targets is partially polarized. This method is then applied to the monostatic case with numerical examples relying on the JPL (Jet Propulsion Laboratory) full-polarimetric L-band radar data. A matched filter to maximize the power ratio between urban and natural targets is developed. The results show that the same filter is optimal for both ocean and forest targets as natural targets.

Description: The unique characteristics of a spaceborne SAR (synthetic aperture radar) operating in a squint mode include large range walk and large variation in the Doppler centroid as a function of range. A pointing control technique to reduce the Doppler drift and a new processing algorithm to accommodate large range walk are presented. Simulations of the new algorithm for squint angles up to 20 deg and look angles up to 44 deg for the Earth Observing System (Eos) L-band SAR configuration demonstrate that it is capable of maintaining the resolution broadening within 20 percent and the ISLR within a fraction of a decibel of the theoretical value.

Description: A wavelength that lies within a spectral interval of reduced solar emission (a Fraunhofer line) can carry optical communications with reduced interference from direct or reflected background sunlight. Suitable Fraunhofer lines are located within the tuning range of good candidate lasers. The laser should be tunable dynamically to track Doppler shifts in the sunlight incident on any solar system body that may appear in the background as viewed by the receiver. A Fraunhofer filter used with a direct-detection receiver should be tuned to match the Doppler shifts of the source and background. The required tuning calculated here for various situations is also required if, instead, one uses a heterodyne receiver with limited post-detection bandwidth.

Description: The authors investigate microwave imaging of metallic objects using a diversity method and interpret and predict the reconstructed image from an approach based on analysis of the scattering mechanism and a back-projection algorithm used in image retrieval. The connection between the various scattering mechanisms and the reconstructed images is discussed, what the images represent is interpreted, and a prediction is made as to what the image will look like over given spectral and angular windows. A brief description is given of the microwave diversity imaging system and the formulation of the microwave diversity imaging based on the physical optics approximation. The scattering mechanism of a complex shaped metallic object is then briefly reviewed and an alternate approach to interpreting the reconstructed image based on the understanding of the scattering mechanism and the reconstruction algorithm is given. Several numerical and experimental examples are included to support this interpretation approach.

Description: An examination is presented of three techniques used for the efficient computation of fields diffracted by a subreflector that has been shaped by geometrical optics synthesis. It is found that these techniques, which are based on the geometrical theory of diffraction (GTD), produce errors in the computed fields that are specific to shaped reflectors. These errors are examined for a reflector system shaped to produce maximum gain from a tapered feed illumination. The discrepancies are directly related to the caustic being located near an observation point of the GTD calculations. The errors found are localized, and they increase in magnitude as the caustic approaches the main reflector. In a general offset geometry, the location of the caustic may be located arbitrarily close to the main reflector given a prescribed output aperture distribution. For the specific case considered here-the common situation of shaping to produce maximum gain-the caustic is located near the edge of the main reflector and on the reflection shadow boundary. A local correction is derived which creates a uniform solution through the caustic and across the reflection shadow boundary. Away from this point the calculation receeds to the standard GTD solution.

Description: The effect of filtering on the signal-to-noise ratio (SNR) of a coherently demodulated band-limited signal is determined in the presence of worst-case amplitude ripple. The problem is formulated as an optimizaton in the Hilbert space L2. The form of the worst-case amplitude ripple is specified, and the degradation in the SNR is derived in closed form. It is shown that, when the maximum passband amplitude ripple is 2Delta (peak-to-peak), the SNR is degraded by at most (1-Delta-squared), even when the ripple is unknown or uncompensated. For example, an SNR loss of less than 0.01 dB due to amplitude ripple can be assured by keeping the amplitude ripple under 0.42 dB.

Description: Radar cross section (RCS) reduction by absorber covering is experimentally studied by employing microwave diversity imaging. Experimental results show that broadband absorber covering is not effective at reducing the co-polarized (the transmitting and receiving antennas have opposite sense of circular polarization) RCS of a plate when the incident wave approximates the edge-on direction but is effective at reducing the cross-polarized (both the transmitting and receiving antennas have the same sense of circular polarization) RCS for all incident directions. The surface current absorber covering is effective at reducing the nonspecular energy and multiple bounces regardless of the polarization status of the measurement.

Description: The gain of circularly polarized (CP) array antennas realized by proper phasing of sequentially rotated linearly polarized (LP) elements is compared to that of arrays using CP elements and demonstrated by calculations for microstrip patch elements. When element spacing is large and array size is small, the advantages of LP elements are offset by the significant reduction in gain due to high cross polarized lobes in the diagonal planes. For large arrays of closely spaced elements, this gain loss reduces to a negligible amount. However, for spacings above a critical value of about 0.7 wavelengths, unacceptably high gain losses will be incurred.

Description: The use of an imaging radar polarimeter data for unsupervised classification of scattering behavior is described by comparing the polarization properties of each pixel in a image to that of simple classes of scattering such as even number of reflections, odd number of reflections, and diffuse scattering. For example, when this algorithm is applied to data acquired over the San Francisco Bay area in California, it classifies scattering by the ocean as being similar to that predicted by the class of odd number of reflections, scattering by the urban area as being similar to that predicted by the class of even number of reflections, and scattering by the Golden Gate Park as being similar to that predicted by the diffuse scattering class. It also classifies the scattering by a lighthouse in the ocean and boats on the ocean surface as being similar to that predicted by the even number of reflections class, making it easy to identify these objects against the background of the surrounding ocean. The algorithm is also applied to forested areas and shows that scattering from clear-cut areas and agricultural fields is mostly similar to that predicted by the odd number of reflections class, while the scattering from tree-covered areas generally is classified as being a mixture of pixels exhibiting the characteristics of all three classes, although each pixel is identified with only a single class.

Description: The electromagnetic properties of a structure that is both chiral and periodic are investigated using coupled-mode equations. The periodicity is described by a sinusoidal perturbation of the permittivity, permeability, and chiral admittance. The coupled-mode equations are derived from physical considerations and used to examine bandgap structure and reflected and transmitted fields. Chirality is observed predominantly in transmission, whereas periodicity is present in both reflection and transmission.

Description: A method is presented for analyzing a finite planar array of circular microstrip patches fed by coaxial probes. The self- and mutual impedances between array elements are calculated using the method of moments with the dyadic Green's function for a dielectric layer on a ground plane. The patch circuits are determined by using the reaction integral equation. The active input impedance as well as the active element pattern of the array are computed from a knowledge of the resultant patch currents. The calculated results for two-element and eight-element linear arrays are in good agreement with experimental data. The active reflection coefficient and element pattern for the center and edge elements of a two-dimensional array as a function of scan angle are also presented.

Description: The issue of reducing the cost of phased array vehicle antennas through the use of a lens feeding arrangement instead of phase shifters at each element is addressed. In particular, the economic viability of a mobile satellite system (MSAT) is largely dependent on the efficient use of the allocated scarce spectrum and orbit as well as the satellite power. the type of vehicle antenna used will play a critical role in achieving this efficiency. A standard design approach for an electronically steered array uses phase shifters at each element to provide beam steering. A method for reducing the required number of phase shifters by using an R-KR lens feed network is outlined. The authors briefly discuss the phase shifter approach to beam steering, examine various lens feed techniques, and describe the R-KR lens approach. The lens feed network architecture is examined, a computer model for simulation of the array is presented, and the results of analysis of a suggested design for the MSAT application are given. In addition, satellite acquisition and tracking considerations are investigated.

Description: Slot timing recovery in a direct-detection optical PPM communication system can be achieved by processing the photodetector output waveform with a nonlinear device whose output forms the input to a phase-locked loop. The choice of a simple transition detector as the nonlinearity is shown to give satisfactory synchronization performance. The rms phase error of the recovered slot clock and the effect of slot timing jitter on the bit error probability were directly measured. The experimental system consisted of an AlGaAs laser diode (wavelength = 834 nm) and a silicon avalanche photodiode photodetector. The system used Q = 4 PPM signaling and operated at a source data rate of 25 Mbits/s. The mathematical model developed to compute the rms phase error of the recovered clock is shown to be in good agreement with results of actual measurements of phase errors. The use of the recovered slot clock in the receiver resulted in no significant degradation in receiver sensitivity compared to a system with perfect slot timing. The system achieved a bit error probability of 10 to the -6th at a received optical signal energy of 55 detected photons per information bit.

Description: The moment method solution to the problem of a reactively loaded circular patch is presented. Using the reaction integral equation in conjuction with the method of moments, parameters of the Thevenin's equivalent network for the loaded patch are obtained. From the equivalent network parameters an expression for the imput impedance of the loaded patch is derived. A design procedure for a circularly polarized disk antenna is presented. Computed results are compared with the experimental data.

Description: The use of commercially available 1-bit LSI correlator chips whose main function is the correlation of sequences of plus ones and minus ones (rather than zeros and ones) as building blocks in the design of multibit correlators is investigated. A radix-2 number system in which the bit values are + or - 1 (no zero) is discussed. The development of a simple conversion algorithm to find the + or - 1 representation of a number given in 2's complement is presented. Some of the issues raised by this conversion algorithm are discussed. It is shown that, if the analog signal is available, there is a simple step to take before the analog-to-digital conversion in order to improve the overall precision. The construction of multibit correlators based on the + or - 1 system is compared to alternative approaches.

Description: It is appropriate to note that 1988 marks the 100th anniversary of the birth of the reflector antenna. It was in 1888 that Heinrich Hertz constructed the first one, a parabolic cylinder made of sheet zinc bent to shape and supported by a wooden frame. Hertz demonstrated the existence of the electromagnetic waves that had been predicted theoretically by James Clerk Maxwell some 22 years earlier. In the 100 years since Hertz's pioneering work the field of electromagnetics has grown explosively: one of the technologies is that of remote sensing of planet Earth by means of electromagnetic waves, using both passive and active sensors located on an Earth Science Geostationary Platform (ESEP). For these purposes some exquisitely sensitive instruments were developed, capable of reaching to the fringes of the known universe, and relying on large reflector antennas to collect the minute signals and direct them to appropriate receiving devices. These antennas are electrically large, with diameters of 3000 to 10,000 wavelengths and with gains approaching 80 to 90 dB. Some of the reflector antennas proposed for ESGP are also electrically large. For example, at 220 GHz a 4-meter reflector is nearly 3000 wavelengths in diameter, and is electrically quite comparable with a number of the millimeter wave radiotelescopes that are being built around the world. Its surface must meet stringent requirements on rms smoothness, and ability to resist deformation. Here, however, the environmental forces at work are different. There are no varying forces due to wind and gravity, but inertial forces due to mechanical scanning must be reckoned with. With this form of beam scanning, minimizing momentum transfer to the space platform is a problem that demands an answer. Finally, reflector surface distortion due to thermal gradients caused by the solar flux probably represents the most challenging problem to be solved if these Large Space Antennas are to achieve the gain and resolution required of them.

Description: During a period spanning more than 5 years, low elevation radar measurements of rain were systematically obtained in the mid-Atlantic coast of the U.S. Drop size distribution measurements with a disdrometer were also acquired on the same rain days. The drop size data were utilized to convert the radar reflectivity factors to estimated rain rates for the respective rain days of operation. Applying high level algorithms to the rain data, core values of rain intensities were identified (peak rain rates), and families of rain rate isopleths analyzed. In particular, equicircle diameters of the family of isopleths enveloping peak rain intensities were statistically characterized. The presented results represents the analysis of two rain days, 12 radar scans, corresponding to 430 culled rain rate isopleths from an available data base of 22,000 contours, approximately 100 scans encompassing 17 rain days. The results presented show trends of the average rain rate vs. contour scale dimensions, and cumulative distributions of rain cell dimensions which belong to core families of precipitation.

Description: Propagation effects in the aeronautical mobile-satellite service differ from those in the fixed-satellite service and other mobile-satellite services because: small antennas are used on aircraft, and the aircraft body may affect the performance of the antenna; high aircraft speeds cause large Doppler spreads; aircraft terminals must accommodate a large dynamic range in transmission and reception; and due to their high speeds, banking maneuvers, and three-dimensional operation, aircraft routinely require exceptionally high integrity of communications, making even short-term propagation effects very important. Data and models specifically required to characterize the path impairments are discussed, which include: tropospheric effects, including gaseous attenuation, cloud and rain attenuation, fog attenuation, refraction and scintillation; surface reflection (multipath) effects; ionospheric effects such as scintillation; and environmental effects (aircraft motion, sea state, land surface type). Aeronautical mobile-satellite systems may operate on a worldwide basis, including propagation paths at low elevation angles. Several measurements of multipath parameters over land and sea were conducted. In some cases, laboratory simulations are used to compare measured data and verify model parameters. The received signals is considered in terms of its possible components: a direct wave subject to atmospheric effects, and a reflected wave, which generally contains mostly a diffuse component.

Description: In 1992, an Engineering Test Satellite 6 is scheduled to be launched by an H-2 rocket. The missions of ETS-6 are to establish basic technologies of inter-satellite communications using S-band, millimeter waves and optical beams and of fixed and mobile satellite communications using multibeam antenna on board the satellite. A plan of the experiments is introduced.

Description: The JPL Channel Simulator lab was modified to allow full duplex links and to allow the use of field propagation data for link fading. This capability will be used to test equipment for the joint AUSSAT/NASA mobile satellite experiment in July 1989.

Description: Propagation experiments for maritime, aeronautical, and land mobile satellite communications were performed using Engineering Test Satellite-Five (ETS-5). The propagation experiments are one of major mission of Experimental Mobile Satellite System (EMSS) which is aimed for establishing basic technology for future general mobile satellite communication systems. A brief introduction is presented for the experimental results on propagation problems of ETS-5/EMSS.

Description: Land-mobile satellite propagation measurements were implemented at L Band (1.5 GHz) in South-Eastern Australia during an 11 day period in October 1988. Transmissions (CW) from both the Japanese ETS-5 and INMARSAT Pacific geostationary satellites were accessed. Previous measurements in this series were performed at both L Band (1.5 GHz) and UHF (870 MHz) in Central Maryland, North-Central Colorado, and the southern United States. The objectives of the Australian campaign were to expand the data base acquired in the U.S. to another continent, to validate a U.S. derived empirical model for estimating the fade distribution, to establish the effects of directive antennas, to assess the isolation between co- and cross-polarized transmissions, to derive estimates of fade as well as non-fade durations, and to evaluate diversity reception. All these objectives were met.

Description: Results from the most recent MSAT-X field experiments, the Tower-3 Experiment and the JPL/FAA/INMARSAT MARECS-B2 Satellite Experiment, are presented. Results that distinguish the propagation environment of the tower set-up are given and explained. The configuration and flight variables of the aeronautical experiment which used an FAA aircraft and an INMARSAT satellite are described. Results that highlight the disturbances on the aeronautical satellite channel are presented. The roles of satellite-induced signal variations and of multipatch are identified and their impact on the link is discussed.

Description: Future communication systems will move toward the 20 to 30 GHz frequency range for wider bandwidth and reduced interference, and will use small earth terminals. The ESA satellite OLYMPUS is scheduled for launch this June and will be ready for use in October. OLYMPUS has 12, 20, and 30 GHz beacons. Virginia Tech and Michigan Tech are working with NASA/JPL on an OLYMPUS experiment and hardware development program. OLYMPUS beacons provide coverage of the east coast of the US sufficient for attenuation measurements. The planned hardware for the OLYMPUS experiments is illustrated. The components of the experiment are summarized. A block diagram level overview of a typical channel is given and one of the four RF front ends is shown.

Description: ACTS counters fading by resource sharing between the users. It provides a large margin only for those terminals which are at risk by unfavorable atmospheric conditions. ACTS, as an experimental satellite, provides a 5 dB clear weather margin and 10 dB additional margin via rate reduction and encoding. For the uplink, this margin may be increased by exercising uplink power control. Some of the challenges faced by the radiowave propagation community are listed. The issue of needs for the satellite are listed, both general and specific.

Description: Some information is given on the ITALSAT millimetric waves propagation experiment, which is to be conducted with the ITALSAT satellite, whose launch is foreseen for the middle of 1990. The purpose of the experiment is one of experimenting with advanced technologies and techniques employing the 20/30 GHz bands in wideband telecommunications. Among the most qualified features of this system are the multispot antenna and the exchange function performed directly onboard. Details of the experiment are given.

Description: Ground based radiometer measurements at 20.6, 31.65, and 90.0 GHz were analyzed to provide attenuation statistics, thus extending the data base of previous NAPEX studies. Using data from colocated radiosondes, comparisons of measurements and calculations of brightness temperatures are presented. The oxygen absorption model of Rosenkranz and the water vapor absorption models of Liebe and of Waters are used. Data from July 1987 at San Nicolas Island, California and from December 1987, August and November 1988 at Denver, Colorado, are included. Joint attenuation statistics at 20.6 and 31.65 GHz are presented for two locations of the Colorado Research Network for December 1987 and August 1988.

Description: The need to develop accurate models for secondary statistics of fading land mobile satellite signals has motivated a study of fading signal autocorrelations and multipath spectrum. Results of autocorrelations and power spectral densities from measured data are presented and comparisons to multipath spectrum models are made.

Description: Beam-waveguide (BWG) antennas provide multiple frequency band operations and other operational benefits for large ground-station antennas. Present design practices use diffraction analyses that ignore the presence of the BWG enclosure and may be inaccurate at lower frequency bands for ground-station antennas operating over multiple frequency bands. Introduced here is a new analysis approach that considers the presence of the BWG enclosure. Results based on the new analysis have revealed new understandings of the performance degradation mechanisms in a BWG antenna and have provided direction for potential design improvements.

Description: The benefits of improved radiometric tracking data have been studied for planetary approach within the inner Solar System using the Mars Rover Sample Return trajectory as a model. It was found that the benefit of improved data to approach and encounter navigation was highly dependent on the a priori uncertainties assumed for several non-estimated parameters, including those for frame-tie, Earth orientation, troposphere delay, and station locations. With these errors at their current levels, navigational performance was found to be insensitive to enhancements in data accuracy. However, when expected improvements in these errors are modeled, performance with current-accuracy data significantly improves, with substantial further improvements possible with enhancements in data accuracy.

Description: It is demonstrated how the use of interleaving/deinterleaving in trellis-coded modulation (TCM) systems can reduce the signal-to-noise ratio loss due to imperfect carrier demodulation references. Both the discrete carrier (phase-locked loop) and suppressed carrier (Costas loop) cases are considered and the differences between the two are clearly demonstrated by numerical results. These results are of great importance for future communication links to the Deep Space Network (DSN), especially from high Earth orbiters, which may be bandwidth limited.

Description: Thermal measurements of microwave transmitter feedhorn windows were performed using an imaging infrared radiometer. The measurement technique is described and results are presented for windows made of 0.001-in. Kapton (trademark of Dupont Chemical Co.) and 0.1-in. HTP-6 (Space Shuttle tile material). Measured and calculated temperatures agree well.

Description: The design and testing of the prototype horn for the proposed 1-megawatt radar are described. The unique features of this square horn include a multiflare design in which flare angle changes rather than corrugations are used to generate the required higher-order modes. A five-port combining section is used at the input. The design of this section and the multiflare section are described. Measured radiation patterns are in good agreement with theoretical patterns.

Description: Aperture efficiency measurements made during 1988 on the three 70-m stations (DSS-14, DSS-43, and DSS-63) at X-band (8420 MHz) and S-band (2295 MHz) have been analyzed and reduced to yield best estimates of antenna gain versus elevation. The analysis has been carried out by fitting the gain data to a theoretical expression based on the Ruze formula. Newly derived flux density and source-size correction factors for the natural radio calibration sources used in the measurements have been used in the reduction of the data. Peak gains measured at the three stations were 74.18 (plus or minus 0.10) dBi at X-band, and 63.34 (plus or minus 0.03) dBi at S-band, with corresponding peak aperture efficiencies of 0.687 (plus or minus 0.015) and 0.762 (plus or minus 0.006), respectively. The values quoted assume no atmosphere is present, and the estimated absolute accuracy of the gain measurements is approximately plus or minus 0.2 dB at X-band and plus or minus 0.1 dB at S-band (1-sigma values).

Description: The characteristics of the Synthetic Aperture Radar (SAR) antenna aboard the ESA Remote Sensing Satellite (ERS-1) are presented. The antenna is folded into a dense package for launch and is deployed in orbit. The design requirements and constraints, their impact on the design, and the resulting features of the mechanisms are discussed.

Description: The various formulations of Maxwell's equations are reviewed with emphasis on those formulations which most readily form analogies with Navier's equations. Analogies involving scalar and vector potentials and electric and magnetic field components are presented. Formulations allowing for media with dielectric and conducting properties are emphasized. It is demonstrated that many problems in electromagnetism can be solved using the NASTRAN finite element code. Several fundamental problems involving time harmonic solutions of Maxwell's equations with known analytic solutions are solved using NASTRAN to demonstrate convergence and mesh requirements. Mesh requirements are studied as a function of frequency, conductivity, and dielectric properties. Applications in both low frequency and high frequency are highlighted. The low frequency problems demonstrate the ability to solve problems involving media inhomogeneity and unbounded domains. The high frequency applications demonstrate the ability to handle problems with large boundary to wavelength ratios.

Description: The objective of any radar experiment is to determine as much as possible about the entities which scatter the radiation. This review discusses many of the various parameters which can be deduced in a radar experiment, and also critically examines the procedures used to deduce them. Methods for determining the mean wind velocity, the RMS fluctuating velocities, turbulence parameters, and the shapes of the scatterers are considered. Complications with these determinations are discussed. It is seen throughout that a detailed understanding of the shape and cause of the scatterers is important in order to make better determinations of these various quantities. Finally, some other parameters, which are less easily acquired, are considered. For example, it is noted that momentum fluxes due to buoyancy waves and turbulence can be determined, and on occasions radars can be used to determine stratospheric diffusion coefficients and even temperature profiles in the atmosphere.

Description: Fundamental methods of signal processing used in normal mesosphere stratosphere troposphere (MST) radar observations are described. Complex time series of received signals obtained in each range gate are converted into Doppler spectra, from which the mean Doppler shift, spectral width and signal-to-noise ratio (SNR) are estimated. These spectral parameters are further utilized to study characteristics of scatterers and atmospheric motions.

Description: The correlation and spectral analysis methods for uniformly sampled stationary random signals, estimation of their spectral moments, and problems arising due to nonstationary are reviewed. Some of these methods are already in routine use in atmospheric radar experiments. Other methods based on the maximum entropy principle and time series models have been used in analyzing data, but are just beginning to receive attention in the analysis of radar signals. These methods are also briefly discussed.

Description: Two concepts of fundamental importance are reviewed: the autocorrelation function and the frequency power spectrum. In addition, some turbulence concepts, the relationship between radar signals and atmospheric medium statistics, partial reflection, and the characteristics of noise and clutter interference are discussed.

Description: Discussed here is a kind of radar called atmospheric radar, which has as its target clear air echoes from the earth's atmosphere produced by fluctuations of the atmospheric index of refraction. Topics reviewed include the vertical structure of the atmosphere, the radio refractive index and its fluctuations, the radar equation (a relation between transmitted and received power), radar equations for distributed targets and spectral echoes, near field correction, pulsed waveforms, the Doppler principle, and velocity field measurements.

Description: The principle of pulse modulation used in the case of coherent scatter radars (MST radars) is discussed. Coherent detection and the corresponding system configuration is delineated. Antenna requirements and design are outlined and the phase-coherent transmitter/receiver system is described. Transmit/receive duplexers, transmitters, receivers, and quadrature detectors are explained. The radar controller, integrator, decoder and correlator design as well as the data transfer and the control and monitoring by the host computer are delineated. Typical operation parameters of some well-known radars are summarized.

Description: Radio telecommunication links are used for communication with deep space probes. These links consist of sinusoidal carrier signals at radio frequencies (RF) modulated with information sent between the spacecraft and the earth. This carrier signal is a very pure and stable sinusoid, typically derived from an atomic frequency standard whose frequency and phase are used to measure the radial velocity of the probe and from this and other data types derive its trajectory. This same observable can be used to search for space-time distortions cased by low frequency (0.1 to 100 MHz) gravitation radiation. How such a system works, what its sensitivity limitations are, and what potential future improvements can be made are discussed.

Description: Future space missions such as the Earth Science Geostationary Platform (ESGP) will require highly accurate antennas with apertures that cannot be launched fully formed. The operational orbits are often inaccessible to manned flight and will involve expendable launch vehicles such as the Delta or Titan. There is therefore a need for completely deployable antenna reflectors of large size capable of efficiently handling millimeter wave electromagnetic radiation. The parameters for the type of mission are illustrated. The logarithmic plot of frequency versus aperture diameter shows the regions of interest for a large variety of space antenna applications, ranging from a 1500-meter-diameter radio telescope for low frequencies to a 20-meter-diameter infrared telescope. For the ESGP, a major application is the microwave radiometry at high frequencies for atmospheric sounding. Almost all existing large antenna reflectors for space employ a mesh-type reflecting surface. Examples are shown and discussed which deal with the various structural concepts for mesh antennas. Fortunately, those concepts are appropriate for creating the very large apertures required at the lower frequencies for good resolution. The emphasis is on the structural concepts and technologies that are appropriate to fully automated deployment of dish-type antennas with solid reflector surfaces. First the structural requirements are discussed. Existing concepts for fully deployable antennas are then described and assessed relative to the requirements. Finally, several analyses are presented that evaluate the effects of beam steering and segmented reflector design on the accuracy of the antenna.

Description: Two approaches for calculating the compensating feed array complex excitations are namely, the indirect conjugate field matching (ICFM) and the direct conjugate field matching (DCFM) approach. In the ICFM approach the compensating feed array excitations are determined by considering the transmitting mode and the reciprocity principle. The DCF, in contrast calculates the array excitations by integrating directly the induced surface currents on the reflector under a receiving mode. DCFM allows the reflector to be illuminated by an incident plane wave with a tapered amplitude. The level of taper can effectively control the sidelobe level of the compensated antenna pattern. Both approaches are examined briefly.

Description: A group of propagation researchers have joined to prepare for a major campaign of propagation experiments for fixed satellite services using the Olympus satellite. For several years, the receiving hardware and data processing procedures have been planned, now, with the launch of the Olympus satellite imminent, experimenters are eager to start the real work. A short review is given of the accomplishments made since the last NAPEX meeting.

Description: Ground based radiometric observations of atmospheric attenuation at 20.6, 31.65, and 90.0 GHz were made at Wallops Island, Virginia during April and May 1989. Early results from the analysis of the data set are compared with previous observations from California and Colorado. The relative attenuation ratios observed at each frequency during clear, cloudy, and rainy conditions are shown. Plans for complete analysis of the data are described.

Description: Year to year variations in the cumulative distributions of rain rate or rain attenuation are evident in any of the published measurements for a single propagation path that span a period of several years of observation. These variations must be described by models for the prediction of rain attenuation statistics. Now that a large measurement data base has been assembled by the International Radio Consultative Committee, the information needed to assess variability is available. On the basis of 252 sample cumulative distribution functions for the occurrence of attenuation by rain, the expected year to year variation in attenuation at a fixed probability level in the 0.1 to 0.001 percent of a year range is estimated to be 27 percent. The expected deviation from an attenuation model prediction for a single year of observations is estimated to exceed 33 percent when any of the available global rain climate model are employed to estimate the rain rate statistics. The probability distribution for the variation in attenuation or rain rate at a fixed fraction of a year is lognormal. The lognormal behavior of the variate was used to compile the statistics for variability.

Description: A simple computational procedure is synthesized to process changes in the microwave-antenna pathlength-error measure when there are changes in the antenna structure model. The procedure employs structural modification reanalysis methods combined with new extensions of correlation analysis to provide the revised rms pathlength error. Mainframe finite-element-method processing of the structure model is required only for the initial unmodified structure, and elementary postprocessor computations develop and deal with the effects of the changes. Several illustrative computational examples are included. The procedure adapts readily to processing spectra of changes for parameter studies or sensitivity analyses.

Description: A development model antenna positioner mechanism with an integral 60 GHz radio frequency beam waveguide is discussed. The system features a 2-ft diameter carbon-fiber reinforced epoxy antenna reflector and support structure, and a 2-degree-of-freedom elevation over azimuth mechanism providing hemispherical field of view. Emphasis is placed on the constraints imposed on the mechanism by the radio frequency subsystems and how they impacted the mechanical configuration.

Description: The quest for the highest resolution microwave imaging and principle of time-domain imaging has been the primary motivation for recent developments in time-domain techniques. With the present technology, fast time varying signals can now be measured and recorded both in magnitude and in-phase. It has also enhanced our ability to extract relevant details concerning the scattering object. In the past, the interface of object geometry or shape for scattered signals has received substantial attention in radar technology. Various scattering theories were proposed to develop analytical solutions to this problem. Furthermore, the random inversion, frequency swept holography, and the synthetic radar imaging, have two things in common: (1) the physical optic far-field approximation, and (2) the utilization of channels as an extra physical dimension, were also advanced. Despite the inherent vectorial nature of electromagnetic waves, these scalar treatments have brought forth some promising results in practice with notable examples in subsurface and structure sounding. The development of time-domain techniques are studied through the theoretical aspects as well as experimental verification. The use of time-domain imaging for space robotic vision applications has been suggested.

Description: The participation of the United States in Olympus experiments is outlined. These include, basic propagation measurement, the Cooperative Data Exchange Experiment (CODE), a rain scatter interference measurement, a small scale diversity experiment, the Personal Access Satellite System (PASS), and all systems that use adaptive fade compensation techniques similar to the Advanced Communications Technology Satellite (ACTS) of NASA.

Description: A study was undertaken to see if magnetic forces can be used at the Space Station to attract or repel spacecrafts such as the Orbital Manuevering Vehicle (OMV) or the Orbiter. A large magnet, in the form of a current loop, is assumed to be placed at the Space Station and another one on the spacecraft. The expression for the force between the two dipoles (loops) is obtained. Using a force of 15 Newtons (3.4 pounds) in order to move the spacecraft, the number of ampere-turn needed in the current loops was calculated at various distances between them. The expression for the force of attraction between a current loop and a soft magnetic material was also examined and the number of amp-turn needed to provide a force of one-tenth of a pound at various distances is also calculated. This one tenth of a pound force would be used in a life line system for the retrieval of an adrift crewman or tool at the Space Station. The feasibility of using conventional antenna on the Station and the incoming vehicle for attraction or repulsion was also examined.

Description: The main objective of this research is to develop an algorithm for isolated-word recognition. This research is focused on digital signal analysis rather than linguistic analysis of speech. Features extraction is carried out by applying a Linear Predictive Coding (LPC) algorithm with order of 10. Continuous-word and speaker independent recognition will be considered in future study after accomplishing this isolated word research. To examine the similarity between the reference and the training sets, two approaches are explored. The first is implementing traditional pattern recognition techniques where a dynamic time warping algorithm is applied to align the two sets and calculate the probability of matching by measuring the Euclidean distance between the two sets. The second is implementing a backpropagation artificial neural net model with three layers as the pattern classifier. The adaptation rule implemented in this network is the generalized least mean square (LMS) rule. The first approach has been accomplished. A vocabulary of 50 words was selected and tested. The accuracy of the algorithm was found to be around 85 percent. The second approach is in progress at the present time.

Description: The real-time operational requirements for SARCOM translation into a high speed image data handler and processor to achieve the desired compression ratios and the selection of a suitable image data compression technique with as low as possible fidelity (information) losses and which can be implemented in an algorithm placing a relatively low arithmetic load on the system are described.

Description: A simplified procedure is developed to decode the three possible erors in a (23,12) Golay codeword. A computer simulation shows that this algorithm is modular, regular and naturally suitable for both Very Large Scale Integration (VLSI) and software implementation. An extension of this new decoding procedure is used also to decode the 1/2-rate (24,12) Golay code, thereby correcting three and detecting four errors.

Description: The generation of test vectors and design-for-test aspects of the Jet Propulsion Laboratory (JPL) Very Large Scale Integration (VLSI) Viterbi decoder chip is discussed. Each processor integrated circuit (IC) contains over 20,000 gates. To achieve a high degree of testability, a scan architecture is employed. The logic has been partitioned so that very few test vectors are required to test the entire chip. In addition, since several blocks of logic are replicated numerous times on this chip, test vectors need only be generated for each block, rather than for the entire circuit. These unique blocks of logic have been identified and test sets generated for them. The approach employed for testing was to use pseudo-exhaustive test vectors whenever feasible. That is, each cone of logid is tested exhaustively. Using this approach, no detailed logic design or fault model is required. All faults which modify the function of a block of combinational logic are detected, such as all irredundant single and multiple stuck-at faults.

Description: The use of interleaving after convolutional coding and deinterleaving before Viterbi decoding is proposed. This effectively reduces radio loss at low-loop Signal to Noise Ratios (SNRs) by several decibels and at high-loop SNRs by a few tenths of a decibel. Performance of the coded system can further be enhanced if the modulation index is optimized for this system. This will correspond to a reduction of bit SNR at a certain bit error rate for the overall system. The introduction of interleaving/deinterleaving into communication systems designed for future deep space missions does not substantially complicate their hardware design or increase their system cost.

Description: During the past ten years Vector Quantization (VQ) has developed from a theoretical possibility promised by Shannon's source coding theorems into a powerful and competitive technique for speech and image coding and compression at medium to low bit rates. In this survey, the basic ideas behind the design of vector quantizers are sketched and some comments made on the state-of-the-art and current research efforts.

Description: Deep space telemetry is and will remain signal-to-noise limited and vulnerable to interference. A need exists to increase received signal power and decrease noise. This includes going to Ka-band in the mid-1990's to increase directivity. The effects of a wet atmosphere can increase the noise temperature by a factor of 5 or more, even at X-band, but the order of magnitude increase in average data rate obtainable at Ka-band relative to X-band makes the increased uncertainty a good trade. Lowbit error probabilities required by data compression are available both theoretically and practically with coding, at an infinitesimal power penalty rather than the 10 to 15 dB more power required to reduce error probabilities without coding. Advances are coming rapidly in coding, as with the new constraint-length 15 rate 1/4 convolutional code concatenated with the already existing Reed-Solomon code to be demonstrated on Galileo. In addition, high density spacecraft data storage will allow selective retransmissions, even from the edge of the Solar System, to overcome weather effects. In general, deep space communication was able to operate, and will continue to operate, closer to theoretical limits than any other form of communication. These include limits in antenna area and directivity, system noise temperature, coding efficiency, and everything else. The deep space communication links of the mid-90's and beyond will be compatible with new instruments and compression algorithms and represent a sensible investment in an overall end-to-end information system design.

Description: The Tracking and Data Relay Satellite System (TDRSS) is an integral part of the overall NASA Space Network (SN) that will continue to evolve into the 1990's. Projections for the first decade of the 21st century indicate the need for an SN evolution that must accommodate growth int he LEO user population and must further support the introduction of new/improved user services. A central ingredient of this evolution is an Advanced TDRSS (ATDRSS) follow-on to the current TDRSS that must initiate operations by the late 1990's in a manner that permits an orderly transition from the TDRSS to the ATDRSS era. An SN/ATDRSS architectural and operational concept that will satisfy the above goals is being developed. To this date, an SN/ATDRSS baseline concept was established that provides users with an end-to-end data transport (ENDAT) service. An expanded description of the baseline ENDAT concept, from the user perspective, is provided with special emphasis on the TDRSS/ATDRSS evolution. A high-level description of the end-to-end system that identifies the role of ATDRSS is presented; also included is a description of the baseline ATDRSS architecture and its relationship with the TDRSS 1996 baseline. Other key features of the ENDAT service are then expanded upon, including the multiple grades of service, and the RF telecommunications/tracking services to be available. The ATDRSS service options are described.

Description: The results of a low sensitivity Radio Frequency Interference (RFI) survey carried out at the Venus Station of the Goldstone Communications Complex are reported. The data cover the spectral range from 1 GHz to 10.4 GHz with a 10-kHz instantaneous bandwidth. Frequency and power levels were observed using a sweep-frequency spectrum analyzer connected to a 1-m diameter antenna pointed at zenith. The survey was conducted from February 16, 1987 through February 24, 1987.

Description: The Ka-band study team was chartered in late 1987 to bring together all the planning elements for establishing 32 GHz (Ka-band) as the primary downlink frequency for deep-space operation, and to provide a stable baseline from which to pursue that development. This article summarizes the results of that study at its conclusion in mid-1988, and corresponds to material presented to NASA's Office of Space Operations on July 14, 1988. For a variety of reasons, Ka-band is the right next major step in deep-space communications. It offers improved radio metric accuracy through reduced plasma sensitivity and increased bandwidth. Because of these improvements, it offers the opportunity to reduce costs in the flight radio system or in the DSN by allocating part of the overall benefits of Ka-band to this cost reduction. A mission scenario is being planned that can drive at least two and possibly all three of the DSN subnets to provide a Ka-band downlink capability by the turn of the century. The implementation scenario devised by the study team is believed to be feasible within reasonable resource expectations, and capable of providing the needed upgrade as a natural follow-on to the technology development which is already underway.

Description: The calibration of the 70-meter antenna at C-band (5.01 GHz) and L-band (1.668 GHz) is described. This calibration comes after a modification to an existing L-band feed to include the C-band frequencies. The test technique employs noise-adding radiometers and associated equipment running simultaneously at both frequencies. The test procedure is described including block diagrams, and results are presented for efficiency, system temperature, and pointing.

Description: A new very large scale integration (VLSI) architecture for implementing Reed-Solomon (RS) decoders that can correct both errors and erasures is described. This new architecture implements a Reed-Solomon decoder by using replication of a single VLSI chip. It is anticipated that this single chip type RS decoder approach will save substantial development and production costs. It is estimated that reduction in cost by a factor of four is possible with this new architecture. Furthermore, this Reed-Solomon decoder is programmable between 8 bit and 10 bit symbol sizes. Therefore, both an 8 bit Consultative Committee for Space Data Systems (CCSDS) RS decoder and a 10 bit decoder are obtained at the same time, and when concatenated with a (15,1/6) Viterbi decoder, provide an additional 2.1-dB coding gain.

Description: Four techniques for uniform sampling of band-bass signals are examined. The in-phase and quadrature components of the band-pass signal are computed in terms of the samples of the original band-pass signal. The relative implementation merits of these techniques are discussed with reference to the Deep Space Network (DSN).

Description: In the present air traffic system, information presented to the transport aircraft cockpit crew may originate from a variety of sources and may be presented to the crew in visual or aural form, either through cockpit instrument displays or, most often, through voice communication. Voice radio communications are the most error prone method for air-ground data link. Voice messages can be misstated or misunderstood and radio frequency congestion can delay or obscure important messages. To prevent proliferation, a multiplexed data link display can be designed to present information from multiple data link sources on a shared cockpit display unit (CDU) or multi-function display (MFD) or some future combination of flight management and data link information. An aural data link which incorporates an automatic speech recognition (ASR) system for crew response offers several advantages over visual displays. The possibility of applying ASR to the air-ground data link was investigated. The first step was to review current efforts in ASR applications in the cockpit and in air traffic control and evaluated their possible data line application. Next, a series of preliminary research questions is to be developed for possible future collaboration.

Description: The Communications Performance and Integration branch of the Tracking and Communications Division has an ongoing involvement in the simulation of its flight hardware for Space Station Freedom. Specifically, the communication process between central processor(s) and orbital replaceable units (ORU's) is simulated with varying degrees of fidelity. The results of investigations into three aspects of this simulation effort are given. The most general area involves the use of computer assisted software engineering (CASE) tools for this particular simulation. The second area of interest is simulation methods for systems of mixed hardware and software. The final area investigated is the application of simulation methods to one of the proposed computer network protocols for space station, specifically IEEE 802.4.

Description: Antennas of 20/30 GHz and higher frequency, due to the small wavelength, offer capabilities for many space applications. With the government-sponsored space programs (such as ACTS) in recent years, the industry has gone through the learning curve of designing and developing high-performance, multi-function antennas in this frequency range. Design and analysis tools (such as the computer modelling used in feedhorn design and reflector surface and thermal distortion analysis) are available. The components/devices (such as BFN's, weight modules, feedhorns and etc.) are space-qualified. The manufacturing procedures (such as reflector surface control) are refined to meet the stringent tolerance accompanying high frequencies. The integration and testing facilities (such as Near-Field range) also advance to facilitate precision assembling and performance verification. These capabilities, essential to the successful design and development of high-frequency spaceborne antennas, shall find more space applications (such as ESGP) than just communications.

Description: Various concepts for large, deployable reflectors were developed and some have flown. In each case the surface material was either a continuous mesh of some sort or an assembly of rigid, continuous-surface facets or petals. Performance issues arise in each case. For mesh, reflectance diminishes with increasing frequency. For rigid sections, seams and relative positioning of the segments have to be dealt with. These two issues prompted the evolution of the concept of an unfurlable, continuous-surface reflector. The concept is described and what is learnt is presented, what is suspected will be learned, and also questions raised yet to be addressed.

Description: The topics of mesh reflectors, methods of analysis, measurements, problems of current interest, and future research, are those which should be addressed in assessing the current state of metallic mesh technology for spaceborne reflector antennas. The study of the properties of the conducting mesh material is discussed. To calculate the radiation patterns of antennas with conducting mesh reflectors, the electromagnetic properties of the mesh material must be integrated into an appropriate reflector antenna computer code. Such a code would take into account such factors as the curvature of the reflector surface, the radiation pattern(s) of the feed(s), etc. Many organizations have developed their own codes for these calculations. An excellent example of such a code is the one developed by Rahmat-Samii and Lee.

Description: Concepts that were studied for application in space based radar (SBR) systems are presented. These antenna systems were for low earth orbit and require large fields of view (FOV). The systems included both space-fed and corporate-fed arrays.

Description: For most applications in space for which they were tried, inflatable structures show a significant weight reduction when compared to mechanical structures. Inflatables are unmatched when compared to mechanical structures when packaged volume is considered. The reliability of deployment of inflatable structures was known for years. When properly designed, such a system is inherently more reliable because it has very few points of failure. Fully inflatable vs. rigidized inflatable structures are discussed. The L'Garde solar concentrator experience is described. Reflector surface and cylinder rigidization, improvement in gore design tools, and expected advances in rigidization schemes with near future are examined.

Description: During this period, the computations of the impedance elements were completed. These include interactions between the two electric current modes, the elecric current mode and the magnetic current mode, and the two magnetic current modes. An accurate and efficient formulation of computing interactions between electric current mode and magnetic current mode was accomplished. This, together with other subroutines allows for the fill-in of all the elements in the matrix. After the fill-in of the impedance elements in the matrix, the forward problem is accomplished. That is, given the specification of the horn and the excitating waveguide mode, the radiation pattern of the antenna based on the integral equation can be obtained. An example case was run for a standard X-band gain-horn (DBG-520). The H- and E-plane patterns of this horn antenna with perfectly conducting walls are compared with the gain pattern available from the manufacturer for up to the first side lobe. Good agreements are obtained although the cross polarization has not yet been accounted for. The effect of the lossy coating on the radiation pattern was also investigated. The resulting E-plane pattern shows about 3-dB improvement in the first sidelobe and 4-dB improvement in the second sidelobe.

Description: Two models of a flat plate for nonprincipal-plane scattering are explored. The first is a revised version of the Physical Optics/Physical Theory of Diffraction (PO/PTD) model with second-order PTD equivalent currents included to account for second-order interactions among the plate edges. The second model uses a heurisitcally derived corner diffraction coefficient to account for the corner scattering mechanism. The patterns obtained using the newer models were compared to the data of previously reported models, the Moment Method (MM), and experimental results. Near normal incidence, all the models agreed; however, near grazing incidence a need for higher-order and corner diffraction mechanisms was noted. In many instances the second-order and corner-scattered fields which were formulated improved the results.

Description: Spar Aerospace has been active in the design and definition of Mobile Satellite Systems since the mid 1970's. In work sponsored by the Canadian Department of Communications, various payload configurations have evolved. In addressing the payload configuration, the requirements of the mobile user, the service provider and the satellite operator have always been the most important consideration. The current Spar 11 beam satellite design is reviewed, and its capabilities to provide flexibility and potential for network growth within the WARC87 allocations are explored. To enable the full capabilities of the payload to be realized, a large amount of ground based Switching and Network Management infrastructure will be required, when space segment becomes available. Early indications were that a single custom designed Demand Assignment Multiple Access (DAMA) switch should be implemented to provide efficient use of the space segment. As MSAT has evolved into a multiple service concept, supporting many service providers, this architecture should be reviewed. Some possible signalling and Network Management solutions are explored.

Description: Geostar is currently constructing a radiodetermination satellite system to provide position fixes and vehicle surveillance services, and has proposed a digital land mobile satellite service to provide data, facsimile and digitized voice services to low cost mobile users. The different system architectures for these two systems, are reviewed.

Description: A worldwide aeronautical mobile satellite system is about to become operational. The system architecture and access methods have been debated extensively, resulting in the selection of Time Division Multiplexing/Time Division Multiple Access (TDM/TDMA) access for packet data, and Single Channel Per Carrier (SCPC) for voice. These have become standards for airline use, and also satisfy the known requirements of ICAO for safety related communications. Voice communications are expected to absorb a high proportion of satellite bandwidth and power in the future. Here, it is explained why INMARSAT selected Frequency Division Multiple Access/SCPC satellite access for this application.

Description: The X- and S-band system operating noise temperatures of the Deep Space Network (DSN) 70-m antennas are presented. Models of atmosphere and ground noise temperature contributions, as they affect the antenna calibrations, are given for future use in telecommunications link modeling. The measured 70-m antenna network gain/system noise temperature (G/T) performance is presented. Compared with the earlier 64-m antenna network, G/T improvements of from 1.8 dB to 2.5 dB, depending on elevation angle, were achieved. G/T comparisons are made with the DSN/Flight Project Design Handbook and the Voyager telecommunications design control table. Actual Voyager telecommunications link performance is compared with predictions made by TPAP (the Voyager telecommunications prediction and analysis program) and with measured performance of the individual 70-m antennas. A modification in the use of antenna gain, system noise temperature, and atmospheric attenuation in existing telecommunications design control tables is suggested.

Description: The Deep Space Network (DSN) Radio Science System presently implemented within the Deep Space Network was designed to meet stringent requirements imposed by the demands of the Voyager-Neptune encounter and future missions. One of the initial parameters related to frequency stability is discussed. The requirement, specification, design, and methodology for measuring this parameter are described. A description of special instrumentation that was developed for the test measurements and initial test data resulting from the system tests performed at Canberra, Australia and Usuda, Japan are given.

Description: A group of large computer programs are used to predict the farfield antenna pattern of reflector antennas in the thermal environment of space. Thermal Radiation Analysis Systems (TRASYS) is a thermal radiation analyzer that interfaces with Systems Improved Numerical Differencing Analyzer (SINDA), a finite difference thermal analysis program. The programs linked together for this analysis can now be used to predict antenna performance in the constantly changing space environment. They can be used for very complex spacecraft and antenna geometries. Performance degradation caused by methods of antenna reflector construction and materials selection are also taken into consideration. However, the principal advantage of using this program linkage is to account for distortions caused by the thermal environment of space and the hygroscopic effects of the dry-out of graphite/epoxy materials after the antenna is placed into orbit. The results of this type of analysis could ultimately be used to predict antenna reflector shape versus orbital position. A phased array antenna distortion compensation system could then use this data to make RF phase front corrections. That is, the phase front could be adjusted to account for the distortions in the antenna feed and reflector geometry for a particular orbital position.

Description: Conventional reflector antennas are typically designed for up to + or - 20 beamwidths scan. An attempt was made to stretch this scan range to some + or - 300 beamwidths. Six single and dual reflector antennas were compared. It is found that a symmetrical parabolic reflector with f/D = 2 and a single circular waveguide feed has the minimum scan loss (only 0.6 dB at Theta sub 0 = 8 deg, or a 114 beamwidths scan). The scan is achieved by tilting the parabolic reflector by an angle equal to the half-scan angle. The f/D may be shortened if a cluster 7 to 19 elements instead of one element is used for the feed. The cluster excitation is adjusted for each new beam scan direction to compensate for the imperfect field distribution over the reflector aperture. The antenna can be folded into a Cassegrain configuration except that, due to spillover and blockage considerations, the amount of folding achievable is small.

Description: In order to improve tracking capability, radar transponder antennas will soon be mounted on the Shuttle solid rocket boosters (SRB). These four antennas, each being identical cavity-backed helices operating at 5.765 GHz, will be mounted near the top of the SRB's, adjacent to the intertank portion of the external tank. The purpose is to calculate the roll-plane pattern (the plane perpendicular to the SRB axes and containing the antennas) in the presence of this complex electromagnetic environment. The large electrical size of this problem mandates an optical (asymptotic) approach. Development of a specific code for this application is beyond the scope of a summer fellowship; thus a general purpose code, the Numerical Electromagnetics Code - Basic Scattering Code, was chosen as the computational tool. This code is based on the modern Geometrical Theory of Diffraction, and allows computation of scattering of bodies composed of canonical problems such as plates and elliptic cylinders. Apertures mounted on a curved surface (the SRB) cannot be accomplished by the code, so an antenna model consisting of wires excited by a method of moments current input was devised that approximated the actual performance of the antennas. The improvised antenna model matched well with measurements taken at the MSFC range. The SRB's, the external tank, and the shuttle nose were modeled as circular cylinders, and the code was able to produce what is thought to be a reasonable roll-plane pattern.

Description: A quantitative study of the transmission loss through the entire atmosphere for optical frequencies likely to be used for an earth-space communication link using existing data bases on scattering and absorption characteristics of the atmospheric constituents is presented.

Description: A three-dimensional drive simulator for the prediction of Land Mobile Satellite Service (LMSS) multipath propagation was developed. It is based on simple physical and geometrical rules and can be used to evaluate effects of scatterer numbers and positions, receiving antenna pattern, and satellite frequency and position. It is shown that scatterers close to the receiver have the most effect and that directive antennas suppress multipath interference.

Description: Based on present technology, the efficient transfer of RF power in space is feasible. However, many parameters must be taken into consideration when designing the system and the interrelationships of these parameters must also be considered. Once the distance between the orbiting spacecraft is specified and the transmit frequency is chosen, then the maximum size for the transmit and receive antennas is fixed (i.e., Rayleigh Range). Once the level of transmit power and trasmit time is specified, then the minimum number of spacecraft batteries is determined. High power RF transmission allows the satellite designer another option in the design of spacecraft power systems.

Description: An overview of microwave beamed power concepts is given in outline form. Concepts such as power transmission to operational satellites, spacecraft propulsion, lunar/planetary outpost power and planetary rover propulsion are listed in chart form and characterized in columns titled power level, benefits, and comments.

Description: Presented here is a signalling system optimized to ensure expedient call set-up for satellite telephony services in a land mobile environment. In a land mobile environment, the satellite to mobile link is subject to impairments from multipath and shadowing phenomena, which result in signal amplitude and phase variations. Multipath, caused by signal scattering and reflections, results in sufficient link margin to compensate for these variations. Direct signal attenuation caused by shadowing due to buildings and vegetation may result in attenuation values in excess of 10 dB and commonly up to 20 dB. It is not practical to provide a link with sufficient margin to enable communication when the signal is blocked. When a moving vehicle passes these obstacles, the link will experience rapid changes in signal strength due to shadowing. Using statistical models of attenuation as a function of distance travelled, a communication strategy has been defined for the land mobile environment.

Description: The margin that is required to mitigate the near-far problem in a Code Division Multiple Access (CDMA) mobile satellite system is determined by the radio-propagation model selected, the distribution of the users in clear and shadowed environments, and implementation techniques. The use of revenue potential as a means of evaluating the relative merits of CDMA and Frequency Division Multiple Access (FDMA) systems is a convenient way to rationalize the performance of systems using high-gain and low-gain antennas. The revenue potential of CDMA is much greater than the revenue potential for FDMA for a particular satellite design considered.

Description: The use of Code Division Multiple Access (CDMA) to satisfy the diverse requirements of a generic (land, maritime, aeronautical) mobile satellite system (MSS) network design is discussed. Comparisons between CDMA and Frequency Division Multiple Access (FDMA) show that a CDMA network design can support significantly more voice channel allocations than FDMA when relatively simple CDMA correlation receivers are employed, provided that there is sufficient space segment equivalent isotropically radiated power (EIRP). The use of more advanced CDMA receivers can improve the spectral and power efficiency. Although the use of CDMA may not gain immediate and widespread support in the international MSS community, provision for the use of CDMA for a domestic system in the U.S., and possibly for a regional system throughout North America, is likely.

Description: The system architecture proposed for the Mobile Satellite Service (MSS) by the National Aeronautics and Space Administration (NASA)/JPL is presented. The demand assigned Frequency Division Multiple Access (FDMA) scheme is described, and results for the associated network access protocol developed by JPL are presented. Both the total number of users that the system can support and the system spectral efficiency are given for a variety of traffic conditions, including those postulated for the Mobile Satellite System Architectures and Multiple Access Techniques Workshop. The results are given for both first- and second-generation one- and two-satellite systems.