ALBERT

Description: An equation is presented for calculating the heat flow required from the surface of an internally heated windshield in order to prevent the formation of ice accretions during flight in specified icing conditions. To ascertain the validity of the equation, comparison is made between calculated values of the heat required and measured values obtained for test windshields in actual flights in icing conditions. The test windshields were internally heated and provided data applicable to two common types of windshield configurations; namely the V-type and the type installed flush with the fuselage contours. These windshields were installed on a twin-engine cargo airplane and the icing flights were conducted over a large area of the United States during the winters of 1945-46 and 1946-47. In addition to the internally heated windshield investigation, some test data were obtained for a windshield ice-prevention system in which heated air was discharged into the windshield boundary layer. The general conclusions resulting from this investigation are as follows: 1) The amount of heat required for the prevention of ice accretions on both flush- and V-type windshields during flight in specified icing conditions can be calculated with a degree of accuracy suitable for design purposes. 2) A heat flow of 2000 to 2500 Btu per hour per square foot is required for complete and continuous protection of a V-type windshield in fight at speeds up to 300 miles per hour in a moderate cumulus icing condition. For the same degree of protection and the same speed range, a value of 1000 Btu per hour per square foot suffices in a moderate stratus icing condition. 3) A heat supply of 1000 Btu per hour per square foot is adequate for a flush windshield located well aft of the fuselage stagnation region, at speeds up to 300 miles per hour, for flight in both stratus and moderate cumulus icing conditions. 4) The external air discharge system of windshield thermal ice prevention is thermally inefficient and requires a heat supply approximately 20 times that required for an internal system having the same performance.

Description: The icing characteristics, the de-icing rate with hot air, and the effect of impact ice on fuel metering and mixture distribution have been determined in a laboratory investigation of that part of the engine induction system consisting of a three-barrel injection-type carburetor and a supercharger housing with spinner-type fuel injection from an 18-cylinder radial engine used on a large twin-engine cargo airplane. The induction system remained ice-free at carburetor-air temperatures above 36 F regardless of the moisture content of the air. Between carburetor-air temperatures of 32 F and 36 F with humidity ratios in excess of saturation, serious throttling ice formed in the carburetor because of expansion cooling of the air; at carburetor-air temperatures below 32 F with humidity ratios in excess of saturation, serious impact-ice formations occurred, Spinner-type fuel injection at the entrance to the supercharger and heating of the supercharger-inlet elbow and the guide vanes by the warn oil in the rear engine housing are design features that proved effective in eliminating fuel-evaporation icing and minimized the formation of throttling ice below the carburetor. Air-flow recovery time with fixed throttle was rapidly reduced as the inlet -air wet -bulb temperature was increased to 55 F; further temperature increase produced negligible improvement in recovery time. Larger ice formations and lower icing temperatures increased the time required to restore proper air flow at a given wet-bulb temperature. Impact-ice formations on the entrance screen and the top of the carburetor reduced the over-all fuel-air ratio and increased the spread between the over-all ratio and the fuel-air ratio of the individual cylinders. The normal spread of fuel-air ratio was increased from 0.020 to 0.028 when the left quarter of the entrance screen was blocked in a manner simulating the blocking resulting from ice formations released from upstream duct walls during hot-air de-icing.

Description: Flight tests were made in natural icing conditions with two 8-ft-chord heated airfoils of different sections. Measurements of meteorological variables conducive to ice formation were made simultaneously with the procurement of airfoil thermal data. The extent of knowledge on the meteorology of icing, the impingement of water drops on airfoil surfaces, and the processes of heat transfer and evaporation from a wetted airfoil surface have been increased to a point where the design of heated wings on a fundamental, wet-air basis now can be undertaken with reasonable certainty.

Description: An investigation has been made in the Langley two-dimensional low-turbulence pressure tunnel to develop the optimum configuration of a 0.35-chord slotted flap on an NACA 65(sub 1120)-111 airfoil section modified by removing the trailing-edge cusp. The section pitching-moment characteristics and the effects of standard roughness on the section characteristics were determined for the flap retracted at Reynolds numbers ranging from 3.0 x 10(exp 6) to 9.0 x 10(exp 6).

Description: Powered models of three different flying boats were landed in oncoming wave of various heights and lengths. The resulting motions and acceleration were recorded to survey the effects of varying the trim at landing, the deceleration after landing, and the size of the waves. One of the models had an unusually long afterbody. The data for landing with normal rates of deceleration indicated that the most severe motions and accelerations were likely to occur at some period of the landing run subsequent to the initial impact. Landings made at abnormally low trims led to unusually severe bounces during the runout. The least severe landing occurred after a small lending when the model was rapidly decelerated at about 0.4 g in a simulation of the proposed use of braking devices. The severity of the landings increased with wave height and was at a maximum when the wave length was of the order of from one and one-half to twice the over-all length of the model. The models with afterbodies of moderate length frequently bounced clear of the water into a stalled attitude at speeds below flying speed. The model with the long afterbody had less tendency to bounce from the waves and consequently showed less severe accelerations during the landing run than the models with moderate lengths of afterbody.

Description: Theoretical pressure distributions and measured lift, drag, and pitching moment characteristics at three values of Reynolds number are presented for a group of NACA four-digit-series airfoil sections modified for high-speed applications. The effectiveness of flaps applied to these airfoils and the effect of standard leading-edge roughness were also investigated at one value of Reynolds number. Results are also presented of tests of three conventional NACA four-digit-series airfoil sections.

Description: An investigation of the spin and recovery characteristics of a 1/24-scale model of the McDonnell XP-88 airplane has been conducted in the Langley 20-foot free-spinning tunnel. The effects of control settings and movements on the erect and inverted spin and recovery characteristics of the model in the normal loading were determined. Tests of the model in the long-range loading also were made. The investigation included tail-modification, spin-recovery parachute, pilot-escape, and rudder-pedal-force tests. Recoveries were generally satisfactory for spins in the normal loading provided the ailerons were not held against the spin. Satisfactory recoveries were obtained regardless of the aileron setting when the leading-edge flaps were deflected and normal recovery technique was used or when the horizontal tail was raised 70 inches, full scale. Recoveries were rapid from all inverted spins obtained. In the long-range loading with tanks on, it may be necessary to jettison the tanks in order to obtain recovery. A 12.0-foot spin-recovery parachute at the tail or a 4.0-foot parachute opened on the outer wing tip (drag coefficient of 0.66) was found to be effective for recoveries from demonstration spins. Test results showed that in an emergency the pilot should attempt to escape from the outboard side of the spinning airplane. The rudder-pedal forces in a spin were indicated to be within the capabilities of the pilot.

Description: From flight tests of 0.5-scale models of the Fairchild Lark pilotless aircraft conducted at the flight test station of the Pilotless Aircraft Research Division at Wallops Island, Va., some evaluations of the static longitudinal stability were obtained by analysis of the short-period oscillations induced by the abrupt movement of the rudder elevators. The analysis shows that for the Lark configuration with wing flap deflections of 0 degrees and 15 degrees the static longitudinal stability decreases slightly up to the critical Mach number and than as the Mach number increases further the stability increases greatly.

Description: At the request of the Air Materiel Command, Army Air Forces an investigation of the low-speed, power-off stability and control characteristics of the McDonnell XP-85 airplane is being conducted in the Langley free-flight tunnel. The XP-85 airplane is a parasite fighter carried in a bomb bay of the B-36 airplane. As a part of the investigation a few force tests were made of a 1/5 scale model of the XP-85 with a conventional tail assembly installed in place of the original design five-unit tail assembly. The total area of the conventional assembly was approximately 80 percent of the area of the five-unit assembly. The results of this investigation showed that the conventional tail assembly gave about the same longitudinal stability characteristics as the original configuration and improved the directional and lateral stability.

Description: Flight tests to determine propeller performance have been made of a Curtiss No. 838-102-18 three-blade propeller having trailing-edge extensions on a Republic P-47D-28 airplane in climb and high speed. These tests are a part of a general propeller flight-test program at the Langley Laboratory of the National Advisory Committee for Aeronautics. Results of climb tests indicate that when power is changed from approximately 1475 horsepower at 2550 rpm (roughly normal power) to 2400 horsepower at 2700 rpm (approximately military power) there is a loss in propeller efficiency of 3 percent at an altitude of 7000 feet, and 4 percent at 21,000 feet. At an airplane Mach number of 0.7 there is a gain of 9 percent in propeller efficiency when the power coefficient per blade is increased from 0.06 to 0.09. Optimum power coefficient per blade at this Mach number is estimated to be approximately 0.12. An analysis to determine the effect of the addition of extensions on the performance of the basic propeller blades indicates that climb performance was increased but high-speed performance was reduced. Both effects, however, were small.

Description: An investigation of two 1/14 scale model configurations of an outboard nacelle for the XB-36 airplane was made in the Langley two-dimensional low-turbulence tunnels over a range of airplane lift coefficients (C (sub L) = 0.409 to C(sub L) = 0.943) for three representative flow conditions. The purpose of the investigation was to develop a low-drag wing-nacelle pusher combination which incorporated an internal air-flow system. The present investigation has led to the development of a nacelle which had external drag coefficients of similar order of magnitude to those obtained previously from tests of an inboard nacelle configuration at the corresponding operating lift coefficients and from approximately one-third to one-half of those of conventional tractor designs having the same ratio of wing thickness to nacelle diameter.

Description: Tests have been conducted in the Langley high-speed 7- by 10-foot tunnel over a Mach number range from 0.40 to 0.91 to determine the stability and control characteristics of an 0.08-scale model of the Chance Vought XF7U-1 airplane. The basic lateral stability characteristics of the complete model with undeflected control surfaces are presented in the present report with a very limited analysis of the results.

Description: This report contains the flight-test results of the stalling characteristics measured during the flying-qualities investigation of the Lockheed P-8OA airplane (Army No. 44-85099). The tests were conducted in straight and turning flight with and without wing-tip tanks. These tests showed satisfactory stalling characteristics and adequate stall warning for all configurations and conditions tested.

Description: Qualitative investigations have shown that use of the NACA injection impeller with the R-3350 engine increases the inertia of the fuel-injection system and, when the standard fuel-metering system is used, this increase in inertia results in poor engine acceleration characteristics. This investigation was therefore undertaken to determine whether satisfactory acceleration characteristics of the engine equipped with the injection impeller could be obtained by simple modifications to the fuel-monitoring system. The engine was operated with two types of carburetor; namely, a hydraulic-metering carburetor incorporating a vacuum-operated accelerating pump and a direct-metering carburetor having a throttle-actuated accelerating pump. The vacuum-operated accelerating pump of the hydraulic-metering carburetor was modified to produce satisfactory accelerations by supplementing the standard air chamber with an additional 75-cubic spring. The throttle-actuated accelerating pump of the direct-metering carburetor was modified to produce satisfactory accelerations by replacing the standard 0.028-inch-diameter bleed in the load-compensator balance line with a smaller bleed of 0.0225-inch diameter. The results of this investigation indicated that both carburetors can be easily modified to produce satisfactory acceleration characteristics of the engine and no definite choice between the types of carburetor and accelerating pump can be made. Use of the direct-metering carburetor, however, probably resulted in better fuel distribution to the cylinders during the acceleration period and reduced the backfire hazard because all the fuel is introduced through the injection impeller.

Description: A Douglas C-74 airplane, during a test dive at about 0.525 Mach number, experienced uncontrollable longitudinal oscillations sufficient to cause shedding of the outer wing panels and the subsequent crash of the airplane. Tests of a section of the horizontal tail plane from a C-74 airplane were conducted in the Ames 16-foot high-speed wind tunnel to investigate the possibility of the tail as a contributing factor to the accident. The results of the investigations of fabric-covered elevators in various conditions of surface deformation are presented in this report.

Description: Attempts were made to alleviate the buffeting of external fuel tanks mounted under the wings of a twin-engine Navy fighter plane. The Mach number at which the buffeting began was increased from 0.529 to 0.640 by streamlining the sway braces and increasing the lateral rigidity of the sway brace system. Further increases of the Mach number, at which buffeting began to 0.725, was obtained by moving the external fuel tank to a position under the fuselage.

Description: This report contains the flight-test results of the lateral and directional-stability and control phase (including tests with wing-tip tanks) of a general flying-qualities investigation of the Lockheed P-80A airplane (Army No. 44-85099). These tests were conducted at indicated airspeeds up to 494 miles per hour (0.691 Mach number) at low altitude and up to 378 miles per hour (0.816 Mach number) at high altitude. These tests showed that the flying qualities of the airplane were for the most part in accordance with the requirements of the Army Air Forces Stability and Control Specifications. The only major deficiency noted was the negative lateral stability with the wing-tip tanks installed.

Description: The NACA 23012-4 airfoil was investigated for the purpose of increasing lift by means of blowing out air from the wing, in conjunction with the effect of plain flap of variable contour and slotted flap of 25 percent chord length. The wing also was provided with a hinged nose, to be deflected at will. Air was blown out frcm the wing immediately in front of the flap; also at the opening between wing and hinged nose,tangentially to the surface of the wing. Another device employed to increase maximum lift was a movable slat, to be opened to form a clot. Lift was measured in relation to the volume of blown-out air and considerable increases were observed with increasing volume.

Description: Flight and ground investigations have been made to compare an exhaust-ejector installation with a standard exhaust-collector-ring installation on air-cooled aircraft engines in a twin-engine airplane. The ground investigation allowed that, whereas the standard engine would have overheated above 600 horsepower, the engine with exhaust ejectors cooled at take-off operating conditions at zero ram. The exhaust ejectors provided as much cooling with cowl flaps closed as the conventional cowl flaps induced when full open at low airspeeds. The propulsive thrust of the exhaust-ejector installation was calculated to be slightly less than the thrust of the collector-ring-installation.

Description: The basic principles of the control of TL ongincs are developed on .the basis of a quantitative investigation of the behavior of these behavior under various operating conditions with particular consideration of the simplifications pormissible in each case. Various possible means of control of jet engines are suggested and are illustrated by schematic designs.

Description: Tests of a 1/20-scale model of the Fleetwings XBTK-1 airplane have been performed in the Langley 15-foot free-spinning tunnel to determine the trim tendencies of the airplane at attitudes above the stall. The results of the tests indicated that the model would trim longitudinally only in the normal range of angles of attack and that the yaw trim tendencies for such longitudinal trim conditions were normal. Although wide oscillations in yaw were noted for some conditions, they occurred at angles of attack larger than those indicated as possible for longitudinal trim and spin equilibrium. It appears, therefore, that the oscillatory motions reported for the airplane may have been the direct result of control movements rather than the result of inherent oscillatory tendencies.

Description: The spin and recovery characteristics of the Curtiss-Wright XP-87 airplane, as well as the spin-recovery parachute requirements, the control forces that would be encountered in the spin, and the best method for the crew to attempt an emergency escape, are presented in this report. The characteristics were estimated rather than determined by model tests because the XP-87 dimensional and mass characteristics were considered to be noncritical and because data were available from model tests of several similar airplanes. The study indicated that the recovery characteristics of the airplane will be satisfactory for all loadings if the controls are reversed fully and rapidly. The control forces, however, will probably be beyond the capabilities of the pilot unless some additional balance or a booster is used. A 6-foot tail parachute or a 3.5-foot wing-tip parachute with a drag coefficient of 0.7 will be a satisfactory, emergency spin-recovery device for spin demonstrations. If it is necessary for the crew to abandon the spinning airplane, they should leave from the outboard side of the cockpit.

Description: The results obtained from measurements of gust and draft velocities within thunderstorms for the period July 22, 1946 to July 23, 1946 at Orlando, Florida, are presented herein. These data are summarized in tables I and II, respectively, and are of the type presented in reference 1 for previous flights. Inspection of photo-observer records for the flights indicated that no data on ambient air temperature variations within thunderstorms were obtained.

Description: Tests with a dynamically similar model of the Navy XP4M-1 airplane were made to determine the best way to land the airplane in calm and rough water, to determine its probable ditching performance, and to determine practicable modifications which could be incorporated in the design of the airplane that would improve its ditching characteristics. The results were obtained by making visual observations, by recording longitudinal decelerations,a nd by taking motion pictures of the landings. A list of conclusions from the test results is included.

Description: An investigation has been made in the Langley two-dimensional low-turbulence tunnel to develop the optimum configuration of a 0.35-chord slotted flap on an NACA 65 (112)-111 airfoil section modified by removing the trailing-edge cusp. The results of the investigation indicate that for the optimum configuration at a Reynolds number of 2.4 x 10(exp 6), the flap deflection was 45 degrees and the flap leading-edge radius center was 0.73 percent-chord behind and 4.46 percent-chord below the slot lip. The maximum section lift coefficient for the optimum configuration at a Reynolds number of 2.4 x 10(exp 6) was 2.46 or 0.12 higher than that obtained for an NACA 65-210 airfoil section with a 0.250-chord slotted flap.

Description: This report presents the result of tests of a 0.35-scale model of the Bell P-39N-l airplane. Included are the longitudinal-stability and - control characteristics of the airplane as indicated by tests of the model equipped with each of two different sets of elevators. The results indicate good longitudinal stability and control throughout the speed range encounterable in flight. The variation of estimated stick force with speed was less when the model was equipped with elevators constructed to the theoretical design dimensions than when equipped with elevators as built to scale from measurements of the corresponding-parts of the actual airplane. The predicted stick forces required to produce the normal accelerations attainable in flight are within the limits specified by the Army Air Forces.

Description: Spin tests have been performed in the Langley 20-foot free-spinning tunnel on a 1/35-scale model of the Douglas XB-43 airplane. The spin and recovery characteristics were determined for several loading conditions of the airplane. The effects of installing a dorsal fin and of installing a ventral fin were investigated. Emergency escape of the crew was simulated and the stick and rudder pedal forces necessary to effect recoveries on the airplane were determined.

Description: A preliminary evaluation of the spin and recovery characteristics of the XF3D-1 airplane has been made, based primarily on the results of the free-spinning tunnel tests of a model which closely simulated the XF3D-1 in tail design, tail length, and mass loading. Estimates have been made of the rudder-pedal force that may be encountered in effecting recovery from a spin and of the spin recovery parachute requirements of the airplane for demonstration spins. The method of bail-out which should be used if it becomes necessary for the crew to abandon the airplane during a spin is indicated. It was indicated that the recovery characteristics of the XF3D-1 airplane in the clean condition for erect and inverted spins would be satisfactory for all loadings specified by the contractor as possible on the airplane. However, if a spin is inadvertently entered while the landing flaps are down, recovery may be slow. The slow-down brakes and the landing flaps should be retracted immediately upon the inception of a spinning condition, after which recovery from the spin should be attempted. The pedal force necessary to reverse the rudder during a spin will be within the physical capabilities of the pilot. Opening a 10-foot diameter parachute attached to the tail (laid-out-flat diameter, drag coefficient 0.7) or a 4.5-foot diameter parachute attached to the outboard wing tip will insure satisfactory spin recovery from demonstration spins. If it becomes necessary for the crew to abandon the airplane during a spin, they should leave from the outboard side of the cockpit.

Description: Tests of a 1/7 size model of the Grumman XJR2F-1 amphibian were made in Langley tank no.1 to examine the landing behavior in rough water and to measure the normal and angular accelerations experienced by the model during these landings. All landings were made normal to the direction of wave advance, a condition assumed to produce the greatest accelerations. Wave heights of 4.4 and 8.0 inches (2.5 and 4.7 ft, full size) were used in the tests and the wave lengths were varied between 10 and 50 feet (70 and 350 ft, full size). Maximum normal accelerations of about 6.5g were obtained in 4.4 inch waves and 8.5g were obtained in 8.0 inch waves. A maximum angular acceleration corresponding to 16 radians per second per second, full size, was obtained in the higher waves. The data indicate that the airplane will experience its greatest accelerations when landing in waves of about 20 feet (140 ft, full size) in length.

Description: In the following, high-speed measurements on a swept-back wing are reported. The curves of lift, moment, and drag have been determined up to Mach numbers of M = 0.87, and they are compared to a rectangular wing. Through measurements of the total-head loss behind the wing and through schlieren pictures, an insight into the formation of the compression shock at high Mach numbers has been obtained.

Description: Tests were conducted in calm water in Langley tank no. 2 and in calm and rough water at an outdoor catapult in order to determine the best way to make a forced landing of an Army A-26 airplane and to determine its probable ditching behavior. These tests were requested by the Air Materiel Command, Army Air Forces, in their letter of March 26, 1943, WEL:AW:50.

Description: A series of investigations of several 1/14-scale models of an inboard nacelle for the XB-36 airplane was made in the Langley two-dimensional low-turbulence tunnels. The purpose of these investigations was to develop a low-drag wing-nacelle pusher combination which incorporated an internal air-flow system. As a result of these investigations, a nacelle was developed which had external drag coefficients considerably lower than the original basic form with the external nacelle drag approximately one-half to two-thirds of those of conventional tractor designs. The largest reductions in drag resulted from sealing the gaps between the wing flaps and nacelle, reducing the thickness of the nacelle training-edge lip, and bringing the under-wing air inlet to the wing leading edge. It was found that without the engine cooling fan adequate cooling air would be available for all conditions of flight except for cruise and climb at 40,000 feet. Sufficient oil cooling at an altitude of 40,000 feet may be obtained by the use of flap-type exit doors.

Description: A 1/5.5-size powered dynamic model of the Columbia XJL-1 amphibian was landed in Langley tank no. 1 in smooth water and in oncoming waves of heights from 2.1 feet to 6.4 feet (full-size) and lengths from 50 feet to 264 feet (full-size). The motions and the vertical accelerations of the model were continuously recorded. The greatest vertical acceleration measured during the smooth-water landings was 3.1g. During landings in rough water the greatest vertical acceleration measured was 15.4g, for a landing in 6.4-foot by 165-foot waves. The impact accelerations increased with increase in wave height and, in general, decreased with increase in wave length. During the landings in waves the model bounced into the air at stalled attitudes at speeds below flying speed. The model trimmed up to the mechanical trim stop (20 deg) during landings in waves of heights greater than 2.0 feet. Solid water came over the bow and damaged the propeller during one landing in 6.4-foot waves. The vertical acceleration coefficients at first impact from the tank tests of a 1/5.5-size model were in fair agreement with data obtained at the Langley impact basin during tests of a 1/2-size model of the hull.

Description: Tests were made with a 1/16 size dynamically similar model of the Navy XP2V-1 airplane to study its performance when ditched. The model was ditched in calm water at the Langley tank no. 2 monorail. Various landing attitudes, speeds, and conditions of damage were simulated. The performance of the node1 was determined and recorded from visual observations, by recording time histories of the longitudinal decelerations, and by taking motion pictures of the ditchings From the results of the tests with the model the following conclusions were drawn: 1. The airplane should be ditched at the normal landing attitude. The flaps should be fully extended to obtain the lowest possible landing speed; 2. Extensive damage will occur in a ditching and the airplane probably will dive violently after a run of about 2 fuselage lengths. Maximum longitudinal decelerations up to about 4g will be encountered; and 3. If a trapezoidal hydroflap 4 feet by 2 feet by 1 foot is attached to the airplane at station 192.4, diving will be prevented and the airplane will probably porpoise in a run of about 4 fuselage lengths with a maximum longitudinal deceleration of less than 3.5g.

Description: An investigation of the air-stream fluctuations at the tail of the D-558-1 airplane has been made at high speed for the purpose of determining the vertical region in which the horizontal tail may be placed without becoming subject to tail buffeting. The investigation was made for a range of Mach numbers from 0.775 to 0.907, and a range of vertical positions at the tall to include two proposed horizontal-tail positions. The tests were made at two angles of attack, 0,2 deg. and 4.2 deg., representative, of the angles of attack for high-speed level flight and a pull-out condition.

Description: This report contains the results of tests of a 1/3-scale model of the Lockheed YP-90A "Shooting Star" airplane and a comparison of drag, maximum lift coefficient, and elevator angle required for level flight as measured in the wind tunnel and in flight. Included in the report are the general aerodynamic characteristics of the model and of two types of dive-recovery flaps, one at several positions along the chord on the lower surface of the wing and the other on the lower surface of the fuselage. The results show good agreement between the flight and wind-tunnel measurements at all Mach numbers. The results indicate that the YP-80A is controllable in pitch by the elevators to a Mach number of at least 0.85. The fuselage dive-recovery flaps are effective for producing a climbing moment and increasing the drag at Mach numbers up to at least 0.8. The wing dive-recovery flaps are most effective for producing a climbing moment at 0.75 Mach number. At 0.85 Mach number, their effectiveness is approximately 50 percent of the maximum. The optimum position for the wing dive-recovery flaps to produce a climbing moment is at approximately 35 percent of the chord.

Description: Spin tests of a 1/16-scale model of the Chance Vought XF5U-1 airplane have been performed in the Langley 20-foot free-spinning tunnel. The effect of control position and movement upon the erect and inverted spin and recovery characteristics ae well as the effects of propellers, of stability flaps, and of various revisions to the design configuration have been determined for the normal fighter loading. The investigation also included spin recovery parachute, tumbling, and pilot-escape tests. For the original design configuration, with or without windmilling propellers, the recovery characteristics of the model were considered unsatisfactory. Increasing the maximum upward deflection of the ailavators from 45 deg to 65 deg resulted in greatly improved recovery characteristics. Dimensional revisions to the original airplane configuration, which satisfactorily improved the general spin and recovery characteristics of the model, consisted of: (1) a supplementary vertical tail 34 inches by 59 inches (full-scale) attached to a boom 80 inches aft of the trailing edge of the airplane in the plane of symmetry, (2) a large semispan undersurface spoiler placed along the airplane quarter-chord line and opened on the outboard side in a spin, or (3) two additional vertical tails 64 inches by 52 inches (full-scale) located at the tips of the ailavators. A satisfactory parachute arrangement for emergency spin recovery from demonstration spins was found to be an arrangement consisting of a 13.3-foot parachute attached by a 30-foot towline to the arresting gear mast on the airplane and opened simultaneously with an 8-foot parachute on the outboard end of the wing attached by a 3-foot towline. Tests indicated that pilot escape from a spin would be extremely hazardous unless the pilot is mechanically ejected from the cockpit. Model tumbling tests indicated that the airplane would not tumble.

Description: Spin tests have been conducted in the Langley free-spinning tunnel on a 1/16-scale model of the McDonnell XP-85 airplane with the normal X-tail replaced with a short-coupled conventional tail arrangement. The effect of the conventional tail arrangement and the effects of various modifications upon the spin and recovery characteristics of the model were determined. The results of the tests indicated that installation of the conventional tail arrangement wil not provide satisfactory recoveries from spins of the airplane. Satisfactory recoveries will be obtainable, however, either by installing in addition a very large ventral fin (17.94 sq ft, full-scale) below the tail or by decreasing the width of the fuselage and making it flat sided rearward of the wing trailing edge.

Description: This report presents the results of wind-tunnel tests of a 0.22-scale model of the North American XP-82 airplane with several modifications designed to reduce the buffeting of the airplane. The effects of various modifications on the air flow over the model are shown by means of photographs of tufts. The drag, lift, and pitching-moment coefficients of the model with several of the modifications are shown. The result indicate that, by reflexing the trailing edge of the center section of the wing and modifying the radiator air-scoop gutter and the inboard lower-surface wing fillets, the start of buffeting can be delayed from a Mach number of 0.70 to 0.775, and that the diving tendency of the airplane would be eliminated up to a Mach number of 0.80.

Description: Measurements are described which were taken in the large wind tunnel of the AVA on a rectangular wing "Mustang 2" with nose flap of a chord of 10 percent. Besides force measurements the results of pressure-distribution measurements are given and compared with those on the same profile "without" nose flap.

Description: The results obtained from measurements of gust velocities, draft velocities, and ambient-air temperature within thunderstorms for the period from September 11, 1946 to September 16, 1946 at Orlando, Florida are presented herein. These data are summarized in.and presented.

Description: This report presents comprehensive pressure-distribution measurements on four (4) swept-back wings (phi = 0 deg, 15 deg, 30 deg, and 45 deg) of constant chord and over a large range of angles of attack with symmetrical air flow. The distributions, experimentally obtained, were compared with theoretical ones calculated by the methods of Weissinger and Multhopp.

Description: A low-speed investigation in the Langley propeller-research tunnel of annular air inlets designed to avoid compression shocks and attendant boundary-layer separation on the fuselage ahead of the inlets at transonic flight speeds by maintaining substream flow velocities on the fuselage nose was reported in NACA RM No. L6J04. In the present investigation, one of the original annular inlets was converted by the installation of a canopy and a nose-wheel fairing into a twin side inlet in order to study problems involved in applying such an inlet to a fighter-type airplane. Extensive measurements of pressures on the surface of the model and surveys of the internal flow were conducted at angles of attack of 0 degrees, 3 degrees, and 6 degrees over a wide range of inlet-velocity ratio.

Description: Tests of two-blade propellers having the NACA 4-(3)(06.3)-06 and NACA 4-(3)(06.4)-09 blade designs (blade activity factors of 179 and 263, respectively) have been made in the Langley 8-foot high-speed tunnel through a range of blade angle from 20 degrees to 70 degrees for free-stream Mach numbers from 0.165 to 0.725 to determine the effects of high solidity and compressibility on propeller characteristics. The tests are part of a general investigation of propellers at high forward speeds. Results previously reported for similar tests of two-blade propellers having the NACA 4-308-03 and NACA 4-308-045 blade designs (blade activity factors of 87 and 133, respectively) are included for comparison. The results showed that the 0.06- and 0.09-solidity blades, although producing efficiencies of the order of 90 percent, were less efficient than blades of conventional solidity. The variation in average blade lift coefficient with solidity at a constant blade angle and advance-diameter ratio through the speed range of these tests was found to be analogous to the variation of wing lift coefficient with aspect ratio, indicating that high-solidity blades may be desirable at very high speeds. Because of power limitations of the test equipment, conclusive evidence of the possible favorable effects of increased blade solidity at high speeds was not obtained. Further tests are desirable.

Description: In accordance with a request of the Bureau of Aeronautics, Navy Department, tests were performed in the Langley 20-foot free-spinning tunnel to determine the spin and recovery characteristics of a 1/24 scale model of the Grumman XTB3F-1 airplane. The airplane is a two-place, midwing torpedo bomber equipped with a tractor propeller and an auxiliary jet engine. The effect of control setting and movement on the erect and inverted spin and recovery characteristics of the model were determined for the normal loading. Brief tests with mass extended slightly along the fuselage were also made, however, in order to determine the effect of such a mass variation on elevator effectiveness. Tests were performed to determine the size of emergency spin-recovery tail and wing-tip parachutes required for satisfactory recovery by parachute action alone. The investigation also included emergency pilot-escape tests and tests to determine the rudder pedal and elevator stick forces necessary to move the rudder and elevator for recovery.

Description: The probable spin and recovery characteristics of the XSN2J-1 air-plane have been estimated on the basis of the results of brief test a performed on a model of an airplane of somewhat similar design. The spin-recovery tail-parachute requirements for the airplane were also determined end, in addition, an analysis was made to determine the best method of emergency pilot escape during a spin. The results of the investigation indicate that the recovery characteristics of the airplane will be satisfactory for all probable loading conditions of the airplane. A 6-foot-diameter tall parachute attached to a 30-foot tow-line will be satisfactory as a spin-recovery device for emergency recovery from demonstration spins. If the occupants of the airplane decide to abandon the airplane in a spin, they should leave the airplane from the outboard side of the cockpit and as far rearward as possible.

Description: Tests have been conducted in the Langley high-speed 7- by 10-foot tunnel over a Mach number range from 0.40 to 0.91 to determine the stability and control characteristics of an 0.08-scale model of the Chance Vought XF7U-1 airplane. The aileron characteristics of the complete model are presented in the present report with a very limited analysis of the results.

Description: As one phase of a comprehensive canopy load investigation, conventional front and rear sliding canopies which are typified by installation on the SB2C-4E airplane, were tested in the Langley full-scale tunnel to determine the pressure distributions and the aerodynamic loads on the canopies. A preliminary analysis of the results of these tests is presented in this report. Plots are presented that show the distribution of pressure at four longitudinal stations through each canopy for a range of conditions selected to determine the effects of varying canopy position, yaw, lift coefficient, and power. The results indicate that the maximum loads, based on the external-internal pressure differential, for the front and rear canopies were obtained with the airplane simulating the high speed flight condition. The highest loading on the front canopy was in the exploding direction for the configuration with the front and rear canopies closed. The highest loads on the rear canopy were in the crushing direction with the front canopy open and the rear canopy closed. For most of the simulated flight conditions, the highest loads on the front canopy, per unit area, were over twice as great as the highest loads on the rear canopy when the comparison was made for the most critical canopy configuration in each case. The external pressure distribution over the front and rear canopies, which were fairly symmetrical to 0 degree angle of yaw, were greatly distorted at other yaw attitudes, particularly for the propeller operating conditions. These distorted pressure distributions resulted in local exploding and crushing loads on both canopies which were often considerably higher than the average canopy loads.

Description: A total of 197 hours of time histories of airspeed and altitude have been obtained on Lockheed Constellation airplanes flying between New York, N.Y. and San Francisco, Calif. during May 1946 and June 1946. Data for 130 hours were previously analyzed to determine the probability of attaining excessive airspeeds and Mach numbers and the results have been published. After the publication, data for additional 67 hours became available. All the data were obtained at altitudes less than 20,000 feet and under approximately the same conditions. The combined data have been analyzed to obtain the results given in the tables and figures contained herein. Based on the combined data, the probability of exceeding a given airspeed or Mach number is of the same order of magnitude as that given. The conclusions are, therefore, unchanged.

Description: An analysis has been made of airfoil data taken on several NACA 16-series propeller airfoils from tests of 5-inch-chord models in the Langley 24 inch high-speed tunnel and l2-inch-chord models in the Langley 8 foot high-speed tunnel, This analysis has shown that the combined effects of Reynolds number changes and variations in airfoil characteristics resulting from differences in models and tunnels are such that when 5 inch-chord and l2-inch-chord data are applied to full-scale propeller design at or near the design condition, differences of less than 1 percent in efficiency will be involved.

Description: Free-spinning-tunnel tests have been made on a 1/27-scale model of the Douglas XF3D-1 airplane to confirm a preliminary evaluation made of the airplane spin and recovery characteristics and previously reported. Recovery characteristics were satisfactory for erect and inverted spins when the model was in the clean condition. When the slow-down brakes were open, recoveries were slow. The pedal force necessary to reverse the airplane rudder during a spin will be within the physical capabilities of the pilot. A 10-foot-diameter parachute attached to the tail of the airplane (laid-out-flat diameter, drag coefficient 0.7) or a 4.5-foot-diameter parachute attached to the outboard wing tip will be satisfactory for emergency spin recovery from demonstration spins. If it becomes necessary for the crew to abandon the airplane during a spin, they should leave from the outboard side of the cockpit. The test results indicated spin and recovery characteristics generally similar to those indicated in the preliminary evaluation.

Description: The teat results showed that with either of the three tail arrangements, the model usually spun in flat attitudes with oscillations about the lateral and longitudinal axes. In general, full reversal of the rudder pedals did not stop the spinning rotation. To make the model satisfactorily meet-the spin-recovery requirements it was found that installation of either a very large ventral fin (l7.9 square feet, full scale) below the tail or a somewhat smaller ventral fin and rudder (12.4 square feet, total . full-scale area) with a rudder throw of at least +/-22deg was required. Either a 21.3-foot tail parachute or a 6.4-foot wing-tip parachute (drag coefficient approximately 0.70) appears necessary as an emergency spin-recovery device during demonstration spins.

Description: A preliminary analytical investigation was made to determine the feasibility of the basic idea of controlled failure points as safety valves for the primary airplane structure. The present analysis considers the possibilities of the breakable wing tip which, in failing as a weak link, would relieve the bending moments on the wing structure. The analysis was carried out by computing the time histories of the wing and stabilizer angle of attack in a 10g pull-up for an XF8F airplane with tips fixed and comparing the results with those for the same maneuver, that is, elevator motion but with tips jettisoned at 8g. The calculations indicate that the increased stability accompanying the loss of the wing tips reduces the bending moment an additional amount above that which would be expected from the initial loss in lift and the inboard shift in load. The vortex shed when the tips are lost may induce a transient load requiring that the tail be made stronger than otherwise.

Description: Results obtained from gust and draft velocity measurements within thunderstorms for the period August 17, 1946 to August 19, 1946 at Orlando, Florida are presented herein. These data are summarized in tables I and II and are of the type presented in reference 1 for previous flights. Inspection of photo-observer records taken on the present flights indicated that mo ambient-air temperature data were obtained.

Description: Wind-tunnel tests were made of a 1/25 scale model of the Martin JRM-1 airplane to determine: (1) The longitudinal stability and control characteristics of the JRM-1 model near the water and lateral and directional stability characteristics with power while moving on the surface of the water, the latter being useful for the design of tip floats; (2) The stability and stalling characteristics of the wing with a modified airfoil contour; (3) Stability characteristics of a hull of larger design gross weight; The test results indicated that the elevator was powerful enough to trim the original model in a landing configuration at any lift coefficient within the specified range of centers of gravity. The ground-board tests for evaluating the aerodynamic forces and moments on an airplane in a simulated cross wind indicate a high dihedral effect in the presence of the ground board and, consequently, during low-speed taxying and take-off, large overturning moments would result which would have to be overcome by the tip floats.

Description: The results obtained from measurements of gust velocities, draft velocities, and ambient-air temperature within thunderstorms for the period September 17, 1946 to September 18, 1946 at Orlando, Fla. are presented herein. These data are summarized in tables I, II, and III, respectively, and are of the type presented in reference 1 for previous flights.

Description: The XF-12 airplane was designed by Republic Aviation Corporation to provide the Army Air Forces with a high performance, photo reconnaissance aircraft. A series of air-stream surveys were made n the vicinity of the empennage of a 1/8.33-scale powered model of the XF-12 airplane in the Langley 19-foot pressure tunnel. Surveys of the vortical-tail region were made through a range of yaw angles of plus or minus 20 degrees at a high and low angle of attack. The horizontal-tail surveys were made over a fairly wide range of angles of attack at zero degrees yaw. Several power and flap conditions were investigated. The results are presented in the form a dynamic pressure ratios, sidewash angles, and downwash angles plotted against vertical distance from the fuselage center line. The results of the investigation indicate that a vertical tail located in a conventional position would be in a field of flow where the dynamic pressure ratios at the horizontal tail to be increased; for equal lift coefficients, the effect of power or flap deflection on the direction of flow at any particular point in the region of the horizontal tail is small.

Description: Three methods for calculating span load distribution, those developed by V.M Falkner, Wm. Mutterperl, and J. Weissinger, have been applied to five swept wings. The angles of sweep ranged from -45 degrees to +45 degrees. These methods were examined to establish their relative accuracy and case of application. Experimentally determined loadings were used as a basis for judging accuracy. For the convenience of the readers the computing forms and all information requisite to their application are included in appendixes. From the analysis it was found that the Weissinger method would be best suited to an over-all study of the effects of plan form on the span loading and associated characteristics of wings. The method gave good, but not best, accuracy and involved by far the least computing effort. The Falkner method gave the best accuracy but at a considerable expanse in computing effort and hence appeared to be most useful for a detailed study of a specific wing. The Mutterperl method offered no advantages in accuracy of facility over either of the other methods and hence is not recommended for use.

Description: Preliminary tests have been made of a small burner to meet the requirements for application to supersonic ram jets. The principal requirements were taken as: (1) efficient combustion in a high-velocity air stream, (2) utilization for combustion of only a small fraction of the air passing through the unit, (3) low resistance to air flow, (4) simple construction, and (5) light weight. Tests of a small burner were carried to stream velocities of nearly 150 feet per second and fuel rates such that one-eighth to one-fourth of the total air was involved in combustion. Commercial propane was selected as the fuel since its low boiling point facilitated vaporization. Combustion which was 80 percent complete along with low aerodynamic losses was obtained by injecting the fuel evenly, prior to ignition, and allowing it to mix with the air without appreciably disturbing the stream. The pressure drop due to frictional losses around the burner and to the adjacent inside walls of the ram jet is small compared with the pressure drop due to combustion.

Description: A 1/12-scale model of a horizontal tail of a fighter airplane was tested through the transonic speeds in the high-speed flow over an airplane wing, the surface of which served as a reflection plane for the model. Measurements of lift, elevator-hinge moment, angle of attack, and elevator angle were made in the Mach number range from 0.75 to 1.04 for elevator deflections ranging from 10 degrees to minus 10 degrees, and for angles of attack of minus 1.2 degrees, 0.4 degrees, and 3.4 degrees. The equipment used to measure the hinge moments of the model proved to be unsatisfactory, and for this reason the hinge-moment data are considered to be only qualitative.

Description: Tests to evaluate the effect of a conical windshield on the drag of a bluff body at supersonic speeds were performed for the following configurations: a sharp nose fuselage with stabilizing fins,a blunt nose fuselage with a hemispherical shape, and a blunt nose fuselage with a conical point. Results of the drag coeeficient are described at Mach 1.0 and the greatest Mach number of 1.37.

Description: Investigations were conducted in the Cleveland altitude wind tunnel to determine the performance and operational characteristics of the 19B-2, 19B-8, and 19XS-1 turbojet engines. One objective was to determine the effect of altitude, flight Mach number, and tail-pipe-nozzle area on the performance characteristics of the six-stage and ten-stage axial-flow compressors of the 19B-8 and 19XB-1 engines, respectively, The data were obtained over a range of simulated altitudes and flight Mach numbers. At each simulated flight condition the engine was run over its full operable range of speeds. Performance characteristics of the 19B-8 and 19XB-1 compressors for the range of operation obtainable in the turboJet-engine installation are presented. Compressor characteristics are presented as functions of air flow corrected to sea-level conditions, compressor Mach number, and compressor load coefficient. For the range of compressor operation investigated, changes in Reynolds number had no measurable effect on the relations among compressor Mach number, corrected air flow, compressor load coefficient, compressor pressure ratio, and compressor efficiency. The operating lines for the 19B-8 compressor lay on the low-air-flow side of the region of maximum compressor efficiency; the 19B-8 compressor operated at higher average pressure coefficients per stage and produced a lower over-all pressure ratio than did the 19XB-1 compressor.

Description: The tests reported herein were made for the purpose of determining the high-speed load distribution on the wing of a 3/16 scale model of a scout-bomber airplane. Comparisons are made between the root bending-moment and section torsional-moment coefficients as obtained experimentally and derived analytically. The results show good correlation for the bending-moment coefficients but considerable disagreement for the torsional-moment coefficients.

Description: An investigation of an NACA submerged intake installation on the Ryan FR-1 was conducted to determine the full-scale aerodynamic characteristics of this installation. In addition, tests were conducted on the submerged inlet with revised entrance lips and deflectors to determine the configuration which would result in the best dynamic pressure recovery measured at the inlet for this installation without a major rework of the entrance. Stalling of the air flow over the inner lip surface created excessive dynamic pressure losses with the original entrance. The revised entrance produced a 12-percent increase in dynamic pressure recovery at the design high-speed inlet-velocity ratio and resulted in an improvement of thte critical-speed characteristics of the entrance lip. A complete redesign of the entrance including a decrease in ramp angle and adjustment of lip camber is necessary to secure optimum results from this submerged duct installation.

Description: The results of the first flight test of a swept-back four-wing version of Tiamat (MX-570 model C) which was launched at the NACA Pilotless Aircraft Research Station at W4110PB Island, Va. are presented. In general, the flight behavior was close to that predicted by calculations based an stability theory and oscillating table tests of the autopilot. The flight test thus indicates that the techniques employed to predict automatic stability are valid and practical from an operational viewpoint. The limitations of the method used to predict flight behavior arise from the fact that the calculations assume no coupling among roll, pitch, and yaw, while in actual flight some such coupling does exist.

Description: A wind-tunnel investigation of the Boeing XB-47 full-scale empennage was conducted to provide, prior to flight tests, data required on the effectiveness of the elevator and rudder. The XB-47 airplane is a jet-propelled medium bomber having wing and tail surfaces swept back 35 degrees. The investigation included tests of the effectiveness of the elevator with normal straight sides, with a buldged trailing edge, and with a modified hinge-line gap and tests of the effectiveness of the rudder with a normal straight-sided tab and with a bulged tab.

Description: Partial measurements in flight of the handling qualities of a Grumman XF7F-1 airplane were investigated. Results are for low altitude and normal center of gravity conditions only.

Description: Tests were made in the Langley 7- by 10-foot tunnel on a 0.182-scale model of an F4U-1 airplane with external stores. This paper is concerned mainly with presenting the data obtained in this investigation and with a comparison of some of these data with flight-test results determining the feasibility of estimating flight buffet Mach number from tunnel data. The results of this investigation indicate that the incremental drag coefficient due to external stores may be used to estimate the maximum Mach number that the F4U-1 airplane may reach in flight when it is equipped with external stores. This estimation is conservative for the five configurations investigated by mounts varying from 0 to 10 percent of the flight limit Mach number. The free-stream tunnel Mach number corresponding to sonic flow over the lower surface of the wing in the region of the store is a good indication of the lower limit of buffet in flight of the F4U-1 airplane when equipped with external stores. The fluctuations of total pressure over the horizontal tail are not sufficiently large (maximum of 1 percent q(sub o) to cause buffeting of the airplane.

Description: In Prandtl's airfoil theory the monoplane was replaced by a single lifting vortex line and yielded fairly practical results. However, the theory remained restricted to the straight wing. Yawed wings and those curved in flight direction could not be computed with this first approximation; for these the chordwise lift distribution must be taken into consideration. For the two-dimensional problem the transition from the lifting line to the lifting surface has been explained by Birnbaum. In the present report the transition to the three-dimensional problem is undertaken. The first fundamental problem involves the prediction of flow, profile, and drag for prescribed circulation distribution on the straight rectangular wing, the yawed wing for lateral boundaries parallel to the direction of flight, the swept-back wing, and the rectangular wing in slipping, with the necessary series developments for carrying through the calculations, the practical range of convergence of which does not comprise the wing tips or the break point of the swept-back wing. The second problem concerns the calculation of the circulation distribution with given profile for a slipping rectangular monoplane with flat profile and aspect ratio 6, and a rectangular wing with cambered profile and variable aspect ratio-the latter serving as check of the so-called conversion formulas of the airfoil theory.

Description: Proceeding from the thesis by W. Kinner the present report treats the problem of the circular airfoil in uniform airflow executing small oscillations, the amplitudes of which correspond to whole functions of the second degree in x and y. The pressure distribution is secured by means of Prandtl's acceleration potential. It results in a system of linear equations the coefficients of which can be calculated exactly with the aid of exponential functions and Hankel's functions. The equations necessary are derived in part I; the numerical calculation follows in part II.