ALBERT

Beschreibung: In this paper, an analytical model of a micro-electromechanical (MEM) resonator used as a 4-bit digital-to-analog converter (DAC) is presented. First, we derive the dynamic equation of the 4-bit DAC device, and the nonlinear governing equation is solved by the Galerkin method combined with a shooting technique to simulate the static response, linear eigenvalue problem, and forced vibration response of the device for various electrostatic actuation cases. Also, we optimize the air gaps in the linear domain to ensure enhanced performance of the DAC. Further, to analyze the operation of the DAC in the nonlinear regime, two experimental samples powered by −2 dBm and −12 dBm AC inputs are examined. Forward and backward frequency sweeps are conducted experimentally and analytically. The proposed analytical results are validated by comparison with experimental data. The results indicate that the presented modeling, simulations, and optimization are effective tools for the design of MEM resonator-based circuits.

Beschreibung: In this paper, an integrated microprism matrix for light coupling and optical sensing systems is presented. The matrix was fabricated by use of controlled negative pressure glass thermal reflow process by the use of monocrystalline mold. The single glass microprism had height of 250 µm or 350 µm with base width respectively 350 µm or 500 µm. The matrix was formed by 10 × 10 microprisms with distance between the microprisms from 150 µm to 400 µm. It corresponded to total area of the matrixes from 28 mm2 to 74 mm2. The controlled coupling of the beam into a substrate was obtained through determination of optimal geometric dimensions of microprisms and configuration of a measurement setup. Optimal position of the fluorescence induction light source in relation to the matrixes (0.5 cm to 4.5 cm distance, 30° angle of incidence) and microfluidic channel (4 mm) were determined. The fluorimetric tests (with excitation by 470 nm laser diode in all the experiments) carried out using fluorescein solution, microbeads and porcine oocyte indicated the possibility of using a microprism matrix for fluorimetric image-based 500 nm long-pass detection in lab-on-a-chip platforms.

Beschreibung: In this study, we propose an annular-shaped piezoelectric micromachined ultrasonic transducer (pMUT) based on a Pb(Zr,Ti)O3-based monocrystalline thin film. This pMUT is expected to increase the resonance frequency while maintaining displacement sensitivity, making it superior to an island-shaped pMUT, which is a conventional design. To demonstrate the validity of this assumption, annular- and island-shaped pMUTs with a 60-μm-diameter diaphragm were prototyped and characterized. As a result, the annular-shaped pMUT exhibited a resonance frequency of 11.9 MHz, a static displacement sensitivity of 2.35 nm/V and a transmitting figure-of-merit (FOM) of 28 nm∙MHz/V. On the other hand, the island-shaped pMUT exhibited a resonance frequency of 9.6 MHz and a static displacement of 2.5 nm/V and an FOM of 24 nm∙MHz/V. Therefore, the annular-shaped pMUT was experimentally demonstrated to provide a higher FOM compared to the island-shaped pMUT. In addition, the annular-shaped pMUT with the optimal dimensions is found to be able to keep a relatively large fabrication margin. This is an advantageous point for the practical device fabrication. We believe this design has a potential to become a standard design for high-performance pMUT devices.

Beschreibung: The pressure and temperature inside the tire is mainly monitored by the tire pressure monitoring system (TPMS). In order to improve the integration of the TPMS system, moreover enhance the sensitivity and temperature-insensitivity of pressure measurement, this paper proposes a microelectromechanical (MEMS) chip-level sensor based on stress-sensitive aluminum-silicon hybrid structures with amplified piezoresistive effect and temperature-dependent aluminum-silicon hybrid structures for hardware and software temperature compensations. Two types of aluminum-silicon hybrid structures are located inside and outside the strained menbrane to simultaneously realize the measurement of pressure and temperature. The model of this composite sensor chip is firstly designed and verified for its effectiveness by using finite element numerical simulation, and then it is fabricated based on the standard MEMS process. The experiments indicate that the pressure sensitivity of the sensor is between 0.126 mV/(V·kPa) and 0.151 mV/(V·kPa) during the ambient temperature ranges from -20 ℃ to 100 ℃, while the measurement error, sensitivity and temperature coefficient of temperature-dependent hybrid structures are individually ± 0.91℃, -1.225 mV/(V·℃) and -0.150%/℃. The thermal coefficient of offset (TCO) of pressure measurement can be reduced from -3.553%FS/℃ to -0.375%FS/℃ based on the differential output of the proposed sensor. In order to obtain the better performance of temperature compensation, Elman neural network based on ant colony algorithm is applied in the data fusion of differential output to further eliminate the temperature drift error. Based on which, the overall measured error is within 3.45 kPa, which is less than ±1.15%FS. The thermal coefficient of offset (TCO) is -0.017%FS/℃, and the thermal coefficient of span (TCS) is -0.020%/FS℃. The research results may provide a useful reference for the development of the high-performance MEMS composite sensor for the TPMS system.

Beschreibung: Lead-free or low lead content perovskite materials are explored in photovoltaic devices to mitigate the challenges of toxic lead-based halides. However, the conversion efficiency from such materials is far below compared to its counterparts. Therefore, to make a humble contribution in the development of lead-free or low lead content perovskite solar cells (PSCs) for future thin-film photovoltaic (PV) technology, a simulation study of tin (Sn) and Pb mixed halide (MAPb0.5Sn0.5I3, 1.22 eV) PSC is carried out in this manuscript. The device is further optimized in terms of transport layer and thickness variation to get 15.1% conversion efficiency. Moreover, the optimized narrow bandgap halide (NBH) based device is further deployed in the monolithic tandem configuration with lead-free wide bandgap (1.82 eV) halide, i.e., Cs2AgBi0.75Sb0.25Br6, 1.82eV (WBH) PSC, to mitigate the thermalization as well as transparent Eg losses. Filtered spectrum, current matching, and construction of tandem J-V curve at the current matching point are utilized to design the tandem solar cell under consideration. Tandem device delivered short current density, JSC (15.21 mA.cm-2), open-circuit voltage, VOC (1.95 V), fill factor, FF (74.09 %) and power conversion efficiency, PCE (21.97%). The performance of the devices considered in this work is found to be in good approximation with experimental work.

Beschreibung: The organic thin film transistor (OTFT) has evolved in a big way, eventually replacing inorganic-based solid-state devices. An extensive survey of the literature reveals that the full potential of OTFTs has neither been explored nor exploited for circuit-level implementation for logic circuit design, despite the popularity of these devices. We have fabricated a PBTTT-C14 (poly (2,5-bis (3-tetradecylthiophen 2yl) thieno (3,2b) thiophene)) based OTFT by using a low-cost solution-processable technique via the floating transfer method (FTM). The fabricated OTFT using FTM shows better electrical behavior than its counterpart fabricated by using the conventional solution-processable technique. The superior electrical characteristics of the FTM-derived devices prompted us to develop a compact model of the p-channel OTFT. The compact modeling results of OTFT show a reasonably good agreement with our experimental results. We have also designed and implemented a PBTTT-C14 OTFT-based inverter circuit and ring oscillator circuit to explore the future of organic-based integrated circuits.

Beschreibung: Paper electronics has emerged as an ecofriendly, light, low-cost, and recyclable material for the fabrication of flexible and printed transistors. In this study, we present fully printed organic electrochemical transistors using an active layer of PEDOT:PSS, carbon electrodes, cellulose-based electrolyte, and three different papers as substrates: bond, vegetal, and Lumi Silk, relating the electrical properties to the different morphologies of the paper surfaces. Each paper presents different regularity, diffusion capabilities, and roughness, with significant influence on the transistor performance. The more organized and smooth the surface, the better the electrical characteristics, the best of these being the Lumi Silk, with higher I on/I off ratio of 46, on-current of 8.3 × 10−5 A, V on of 1.3 V, and power gain of 43.5 dB associated with ultra-low hysteresis of 0.1 V, high transconductance of −57.3 μS, and suitablity for flexible electronics and sensors applications.

Beschreibung: There is a growing desire for cell rotation in the field of biophysics, bioengineering and biomedicine. We herein present novel microfluidic channels for simultaneous high-throughput cell self-rotation using local circular streaming generated by ultrasonic wave excited bubble arrays. The bubble traps achieve high homogeneity of liquid-gas interface by setting capillary valves at the entrances of dead-end bubble trappers orthogonal to the main microchannel. In such a highly uniform bubble array, rotation at different fields of bubble-relevant vortices is considered equal and interconvertible. The device is compatible with cells of various size and retains manageable rotation velocity when actuated by signals of varying frequency and voltage. Experimental observations were confirmed consistent with theoretical estimation and numerical simulation. Comparing with the conventional approaches of cell rotation, our device has multiple merits such as high throughput, low cost and simple fabrication procedure, and high compatibility for lab-on-chip integration. Therefore, the platform holds a promise in cell observation, medicine development and biological detection.