ALBERT

Description: Direct measurements were undertaken at the Aeronautics Laboratory in Turin of the aerodynamic actions on an oscillating wing. The tests conducted had as their essential object the examination of the operation of apparatus designed for this measurement. The values experimentally obtained for the aerodynamic coefficients are in good agreement with the theory of oscillatory motion of the wing of finite span and show clear deviation from the values obtained by theory of plane motion.

Description: An investigation is made of the mutual interference of the wings of a biplane under the general assumption that each wing may be replaced by a vortex system of the type given by the Prandtl wing theory. The additional velocities induced at each wing by the presence of the other are determined by the Biot-Savart law and converted into an equivalent change in the angle of attack, the effect being that of an additional twist given to the wings in changing their lift distributions. The lift distributions computed in this manner for several airplane types are compared with the results of measurement.

Description: The purpose of this paper is to give an outline of the present state of development and point out the possibilities available for the further increase in the power/displacement ratio, the economy, and the reliability of the engine. Some of the aspects discussed are methods of increasing take-off power, the various methods of preparation of the fuel mixture and their effect on power, economy, and safety.

Description: For an infinitely long plate strip of constant curvature there is set up the buckling condition for combined shear and axial stresses. Assumptions are made of the vanishing of the moments acting on the longitudinal edges and of the vanishing of the tangential displacements u and the transverse stresses sigma(sub y) (longitudinal stiffeners nonresistant to bending in the circumferential direction). The buckling condition is evaluated for the case of pure shear and an approximate formula is derived for the critical stresses for large curvatures. In connection with the discussion of the methods and results there is defined the range of validity and the buckling condition set up.

Description: This paper restricts itself to radial impellers with cylindrical blades since, as Prasil has shown, the flow about an arbitrarily curved surface of revolution may be reduced to this normal form we have chosen by a relatively simple conformal transformation. This method starts from the simple hypotheses of the older centrifugal impeller theory by first assuming an impeller with an infinite number of blades. How the flow is then modified is then investigated. For the computation of flow for a finite number of blades, the approximation method as developed by Munk, Prandtl and Birnbaum, or Glauert is found suitable. The essential idea of this method is to replace the wing by a vortex sheet and compute the flow as the field of these vortices. The shape of the blades is then obtained from the condition that the flow must be along the surface of the blade.

Description: With regard to the change in shape of the cross section while the area remains constant, no investigation results are as yet available. Such an investigation will be the subject of the present paper. For this purpose it is necessary to consider the velocity and pressure relations over each entire cross section so that we are confronted with a three-dimensional problem.

Description: The most conspicuous of the features of the enlarged N.A.C.A. tank are derived directly from those of the original tank and owe their present form not only to the reasons for their first use but also to the experience obtained with them. As in the original tank, there are: 1) A basin of great length (new 2,880 feet); 2) Rails made of structural H beams, without machining; 3) A towing carriage of very high speed (now 80 mph maximum); 4) Rubber tires on all the wheels, pneumatic on the running wheels and solid on the guide wheels.

Description: This report makes use of the results obtained in the Gottingen ice tunnel in which the atmospheric conditions are simulated and the process of ice formation photographed. The effect of ice formation is threefold: 1) added weight to the airplane; 2) a change in the lift and drag forces; 3) a change in the stability characteristics.

Description: The subject of the present paper is confined to the investigations and methods employed by the Fiat company in their studies on the altitude performance of an air-cooled engine of the production type. The experimental set-up as well as test engine data are provided.

Description: This report derives equations containing only directly measurable constants for the quantities involved in the hydrodynamic theory of detonation. The stable detonation speed, D, is revealed as having the lowest possible value in the case of positive material velocity, by finding the minimum of the Du curve (u denotes the speed of the gases of combustion). A study of the conditions of energy and impulse in freely suspended detonating systems leads to the disclosure of a rarefaction front traveling at a lower speed behind the detonation front; its velocity is computed. The latent energy of the explosive passes into the steadily growing detonation zone - the region between the detonation front and the rarefaction front. The conclusions lead to a new definition of the concept of shattering power. The calculations are based on the behavior of trinitrotoluene.

Description: In the present paper, the complete buckling conditions of stiffened plates are being developed for uniform compression. We shall treat plates with one or two longitudinal or transverse stiffeners at any point, discuss the buckling conditions, and evaluate them for different cases.

Description: As no investigation of supercharging in 2-stroke-cycle engines has been published up to the present, this article is an attempt in that direction, with a view to establishing the mathematical principles and the constructive rules for the design of such engines.

Description: In this report, two reliable methods are presented, with the aid of which the undisturbed flight dynamic pressure and the true static pressure may be determined without error. These problems were solved chiefly through practical flight tests.

Description: Three general theories treating the potential flow about an arbitrary wing section are discussed in this report. The first theory treats the method of conformal transformation as laid down by Theodorsen and Garrick; the second is a generalization of Birnbaum's theory for moderately thick airfoils; the third is a general investigation of the complex velocity function with particular reference to the relations first discussed by F. Weinig.

Description: The results of pressure distribution measurements that were made on a model wing section of a Fieseler F 5 R type airplane are presented. Comparison of those model tests with the corresponding flight tests indicates the limitations and also the advantages of wind tunnel investigations, the advantages being particularly that through the variety of measuring methods employed the more complicated flow conditions may also be clarified. A fact brought out in these tests is that even in the case of "well rounded" slots it is possible for a vortex to be set up at the slot entrance and this vortex is responsible for certain irregularities in the pressure distribution and in the efficiency of the slot.

Description: A method is developed with no neglect of certain factors in mass flow of air and in the drag of the heated radiator, i.e., one under actual operating conditions, as compared with the corresponding values in the cold state, may be simply computed. Although a symmetrical duct radiator has been used to bring out the flow relations, the results apply equally as well to the unsymmetrical radiator shapes usual in airplane construction.

Description: A theory is developed for the airfoil of finite span at supersonic speed analogous to the Prandtl airfoil theory of 1918-1919 for incompressible flow. In addition to the profile and induced drags, account must be taken at supersonic flow of still another drag, namely, the wave drag, which is independent of the wing aspect ratio. Both wave and induced drags are proportional to the square of the lift and depend on the Mach number, that is, the ratio of flight to sound speed. In general, in the case of supersonic flow, the drag-lift ratio is considerably less favorable than is the case for incompressible flow. Among others the following examples are considered: 1) lifting line with constant lift distribution (horseshoe vortex); 2) computation of wave and induced drag and the twist of a trapezoidal wing of constant lift density; 3) computation of the lift distribution and drag of an untwisted rectangular wing.

Description: In the present report, aerodynamic relations under the effect of the weight moments are investigated, and an example given of the computation of the stability for a practical case. Later, the effects of the masses of the controls on the dynamic longitudinal stability will be considered.

Description: This report is an attempt at a new method of coating the surface of the cylinder with materials that undergo chemical change at definite temperatures as indicated by a change in color. In this way it was hoped that the substance itself would indicate directly the position of its isotherms, which in measurements with thermocouples requires a tedious amount of labor.

Description: Recent developments in airfoil-testing methods and fundamental air-flow investigations, as applied to airfoils, are discussed. Preliminary test results, obtained under conditions relatively free from stream turbulence and other disturbances, are presented. Suitable airfoils and airfoil-design principles were developed to take advantage of the unusually extensive laminar boundary layers that may be maintained under the improved testing conditions. The results are of interest mainly in range of below 6,000,000.

Description: Report presents the results of an investigation conducted in the NACA 20-foot tunnel to determine the slipstream drag, the body interference, and the cooling characteristics of nacelle-propeller diameter. Four combinations of geometrically similar propellers and nacelles, mounted on standard wing supports, were tested with values of the ratio of nacelle diameter to propeller diameter of 0.25, 0.33, and 0.44.

Description: An investigation to determine and correlate the experimental surface heat-transfer coefficients of finned cylinders with different air-stream cooling arrangements was conducted at the Langley Memorial Aeronautical Laboratory from 1932 to 1938. The investigation covered the determination of the effect of fin width, fin space, fin thickness, and cylinder diameter on the heat transfer. Wind-tunnel tests were made in the free air stream with and without baffles and also with various devices for creating a turbulent air stream. Tests were also made with blower.

Description: Results are presented showing the effects of gap, elevator, nose shape, balance, cut-out, and tabs on the aerodynamic characteristics of a horizontal tail surface tested in the NACA full-scale tunnel.

Description: Flight tests were made to determine the profile-drag coefficients of a portion of the original wing surface of an all-metal airplane and of a portion of the wing made aerodynamically smooth and more nearly fair than the original section. The wing section was approximately the NACA 2414.5. The tests were carried out over a range of airplane speeds giving a maximum Reynolds number of 15,000,000. Tests were also carried out to locate the point of transition from laminar to turbulent boundary layer and to determine the velocity distribution along the upper surface of the wing. The profile-drag coefficients of the original and of the smooth wing portions at a Reynolds number of 15,000,000 were 0.0102 and 0.0068, respectively; i.e., the surface irregularities on the original wing increased the profile-drag coefficient 50 percent above that of the smooth wing.

Description: An investigation of the interference associated with tail surfaces added to wing-fuselage combinations was included in the interference program in progress in the NACA variable-density tunnel. The results indicate that, in aerodynamically clean combinations, the increment of the high-speed drag can be estimated from section characteristics within useful limits of accuracy. The interference appears mainly as effects on the downwash angle and as losses in the tail effectiveness and varies with the geometry of the combination. An interference burble, which markedly increases the glide-path angle and the stability in pitch before the actual stall, may be considered a means of obtaining satisfactory stalling characteristics for complete combination.

Description: An investigation was made in the NACA 7 by 10-foot wind tunnel of a large-chord NACA 23012 airfoil with several arrangements of 25.66 percent chord slotted flaps to determine the section aerodynamic characteristics as affected by slot shape, flap shape, flap location, and flap deflection. The flap position for maximum lift, the polars for arrangements considered favorable for take-off and climb, and the complete section aerodynamic characteristics for selected optimum arrangements were determined. A discussion is given of the relative merits of the various arrangement for certain selected criterions. A comparison is made of a slotted flap on the NACA 23021 airfoil with a corresponding slotted flap previously developed for the NACA 23012 airfoil.

Description: Measurements were made of the cooling on the fronts of model cylinders in a conventional cowling for cooling in both the ground and the cruising conditions. The mechanisms of front and rear cooling are essentially different. Cooling on the rear baffled part of the cylinders continually increases with increasing fin width. For the front of the cylinder, an optimum fin width was found to exist beyond which an increase in width reduced the heat transfer. The heat transfer coefficient on the front of the cylinders was larger on the side of the cylinder facing the propeller swirl than on the opposite side. This effect became more pronounced as the fin width was increased. These results are introductory to the study of front cooling and show the general effect of several test parameters.

Description: Measurements have been made of the lift on an airfoil in pitching oscillation with a continuous-recording, instantaneous-force balance. The experimental values for the phase difference between the angle of attack and the lift are shown to be in close agreement with theory.

Description: Eight wings and three tails, covering a wide range of aerodynamic characteristics, were independently ballasted so as to be interchangeable with no change in mass distribution. For each of the 24 resulting wing-tail combinations, observations were made of the steady spin for four control settings and of recoveries for five control manipulations. The results are presented in the form of charts comparing the spin characteristics. The tests are part of a general investigation being made in the NACA free-spinning tunnel to determine the effects of systematic changes in wing and tail arrangement upon the steady-spin and the recovery characteristics of a conventional low-wing monoplane for various load distributions.

Description: The extension to a compressible fluid of Lagally's theorem on the moment on a body in an incompressible fluid and Poggi's method of treating the flow of compressible fluids are employed for the determination of the effect of compressibility on the moment of an arbitrary body. Only the case of the two-dimensional subsonic flow of an ideal compressible fluid is considered. As examples of the application of the general theory, two well-known systems of profiles are treated; namely the elliptic profile and the symmetrical Joukowski profiles with sharp trailing edges. The effect of compressibility on the position of the center of pressure is also discussed. Several numerical examples of both the elliptic and the Joukowski profiles are given.

Description: Factors derived from wing theory are presented. By means of these factors, the angle of zero lift, the lift-curve slope, the pitching moment, the aerodynamic-center position, and the induced drag of tapered wings with partial-span flaps may be calculated. The factors are given for wings of aspect ratios 6 and 10 , of taper ratios from 0.25 to 1.00, and with flaps of various length. An example is presented of the method of application of the factors. Fair agreement with experimental results is shown for two wings of different taper ratio having plain flaps of various spacing.

Description: Report presents the results of a great number of tests made to determine the effect of service stresses on the impact resistance, the x-ray diffraction patterns, and the microstructure of 25s aluminum alloy. Many of the specimens were taken from actual propeller blades and others were cut from 13/16-inch rod furnished by the Aluminum Company of America.

Description: Equations have been developed for the analysis of the performance of the ideal airplane, leading to an approximate physical interpretation of the performance problem. The basic sea-level airplane parameters have been generalized to altitude parameters and a new parameter has been introduced and physically interpreted. The performance analysis for actual airplanes has been obtained in terms of the equivalent ideal airplane in order that the charts developed for use in practical calculations will for the most part apply to any type of engine-propeller combination and system of control, the only additional material required consisting of the actual engine and propeller curves for propulsion unit. Finally, a more exact method for the calculation of the climb characteristics for the constant-speed controllable propeller is presented in the appendix.

Description: A 4-stroke-cycle test engine was equipped with a glass cylinder and the air movements within it were studied while the engine was being motored. Different types of air flow were produced by using shrouded intake valves in various arrangements and by altering the shape of the intake-air passage in the cylinder head. The air movements were made visible by mixing feathers with the entering air, and high-speed motion pictures were taken of them so that the air currents might be studied in detail and their velocities measured. Motion pictures were also taken of gasoline sprays injected into the cylinder on the intake stroke. The photographs showed that: a wide variety of induced air movements could be created in the cylinder; the movements always persisted throughout the compression stroke; and the only type of movement that persisted until the end of the cycle was rotation about the cylinder axis.

Description: The strength of modern lightweight thin-wall structures is generally limited by the strength of the compression members. An adequate design of these members requires a knowledge of the compressive stress-strain graph of the thin-wall material. The "pack" method was developed at the National Bureau of Standards with the support of the National Advisory Committee for Aeronautics to make possible a determination of compressive stress-strain graphs for such material. In the pack test an odd number of specimens are assembled into a relatively stable pack, like a "pack of cards." Additional lateral stability is obtained from lateral supports between the external sheet faces of the pack and outside reactions. The tests seems adequate for many problems in structural research.

Description: An investigation was conducted in the NACA full-scale wind tunnel to determine the aerodynamic characteristics of the NACA 0009, 0012, and 0018 airfoils, with the ultimate purpose of providing data to be used as a basis for comparison with other wind-tunnel data, mainly in the study of scale and turbulence effects. Three symmetrical 6 by 36-foot rectangular airfoils were used. The Reynolds number range for minimum drag was form 1,800,000 to 7,000,000 and for maximum lift, from 1,700,000 to 4,500,000. The effect of rounded tips was determined for each of the airfoils. Tests were also made of the NACA 0012 airfoil equipped with a 0.20c full-span split flap hinged at 0.80c. Tuft surveys were included to show the progressive breakdown of flow near maximum lift. Momentum surveys were made in conjunction with force measurements at zero lift as an aid in converting force-test data to section coefficients.

Description: Simultaneous air-flow photographs and pressure-distribution measurements were made of the NACA 4412 airfoil at high speeds to determine the physical nature of the compressibility burble. The tests were conducted in the NACA 24-inch high-speed wind tunnel. The flow photographs were obtained by the Schlieren method and the pressures were simultaneously measured for 54 stations in the 5-inch-chord airfoil by means of a multiple-tube manometer. Following the general program, a few measurements of total-pressure loss in the wake of the airfoil at high speeds were made to illustrate the magnitude of the losses involved and the extent of the disturbed region; and, finally, in order to relate this work to earlier force-test data, a force test of a 5-inch-chord NACA 4412 airfoil was made. The results show the general nature of the phenomenon known as the compressibility burble. The source of the increased drag is shown to be a compression shock that occurs on the airfoil as its speed approaches the speed of sound. Finally, it is indicated that considerable experimentation is needed in order to understand the phenomenon completely.

Description: The results of a research program to obtain design data on the strength of open-channel aluminum-alloy sections subjected to combined column and beam action. The results of the tests of about 70 specimens were graphed for stresses due to axial load and stresses due to bending loading as functions of length to radius of gyration of the specimens. From these graphs a design chart was derived that is suitable for ready use.

Description: Section aerodynamic characteristics of a large-chord N.A.C.A. 23012 airfoil with a slotted deflector flap were obtained in the N.A.C.A. 7- by 10-foot wind tunnel. The characteristics of an N.A.C.A. slotted flap and of a simple split flap are included for comparison. The slotted deflector flap was found to have a somewhat lower maximum lift coefficient and somewhat higher drag at high lift coefficients than the N.A.C.A. slotted flap. The high drag of the open slot with the deflector flap neutral indicates that the slot should be closed for this condition.

Description: Propellers with equal total blade area, but with different numbers, were tested at Stanford University. The tests show generally that, for equal total blade area, propellers with the larger number of blades absorb the greater power and, provided hubs have equal drag, develop the higher efficiency. It is shown that the differences found are in agreement, qualitatively, with what might be predicted from simple blade-element theory.

Description: A solution for the equation of torsional vibration of tapered beams has been found in terms of Bessel functions for beams satisfying the following conditions: (a) the cross sections along the span are similar in shape; and (b) the torsional stiffness of a section can be expressed as a power of a linear function of distance along the span. The method of applying the analysis to actual cases has been described. Charts are given from which numerical values can be immediately obtained for most cases of practical importance. The theoretical values of the frequency ratio have been experimentally checked on five beams having different amounts of taper.

Description: Torsion tests were made on 51ST aluminum-alloy seamless tubes having diameter-to-thickness ratios of from 77 to 139 and length-to-diameter ratios of from 1 to 60. The torsional strengths developed in the tubes which failed elastically (all tubes having lengths greater than 2 to 6 times the diameter) were in most cases within 10 percent of the value indicated by the theories of Donnel, Timoshenko, and Sturm, assuming a condition of simply supported ends.

Description: The N.A.C.A. has conducted tests to provide more complete data than were previously available for estimating the effects of common surface irregularities on wing drag. The irregularities investigated included: brazier-head and countersunk rivets, spot welds, several types of sheet-metal joints, and surface roughness. Tests were also conducted to determine the over-all effect of manufacturing irregularities incidental to riveted aluminum alloy and to spot-welded stainless-steel construction. The tests were made in the 8-foot high speed wind tunnel at Reynolds Numbers up to 18,000,000. The results show that any of the surface irregularities investigated may increase wing drag enough to have important adverse effects on high-speed performance and economy. A method of estimating increases in wing drag caused by brazier-head rivets and lapped joints under conditions outside the range of the tests is suggested. Estimated drag increases due to rivets and lapped joints under conditions outside the range of the tests is suggested. Estimated drag increases due to rivets and lapped joints on a wing of 20-foot chord flying at 250 miles per hour are shown.

Description: A study was made to determine the physical properties of synthetic resins having paper, canvas, and linen reinforcements, and of laminated wood impregnated with a resin varnish. The results show that commercial resins have moduli of elasticity that are too low for structural considerations. Nevertheless, there do exist plastics that have favorable mechanical properties and, with further development, it should be possible to produce resin products that compare favorably with the light-metal alloys. The results obtained from tests on Compound 1840, resin-impregnated wood, show that this material can stand on its own merit by virtue of a compressive strength four times that of the natural wood. This increase in compressive strength was accomplished with an increase of density to a value slightly below three times the normal value and corrected one of the most serious defects of the natural product.

Description: Surface waviness and rib stitching have been investigated as part of a series of tests to determine the effects on wing drag of common surface irregularities. The tests were made in the N.A.C.A. 8-foot high-speed wind tunnel at Reynolds Numbers up to 17,000,000. The results of the tests showed that the waviness common to airplane wings will cause no serious increase in drag unless the waviness exists on the forward part of the wing, where it may cause premature transition or premature compressibility effects. Waves 3 inches wide and 0.048 inch high, for example, increased the drag 1 percent when they covered the rear 67 percent of both surfaces and 10 percent when they covered the rear 92 percent. A single wave 3 inches wide and only 0.020 inch high at the 10.5-percent-chord point on the upper surface caused transition to occur on the wave and increased the drag 6 percent. Rib stitching increased the drag 7 percent when the rib spacing was 6 inches; the drag increment was proportional to the number of ribs for wider spacings. About one-third of the increase was due to premature transition at the forward ends of the stitching.

Description: The various possible means of preventing ice adhesion on airplane surfaces are critically reviewed. Results are presented of tests of the adhesives forces between ice and various solid and liquid forces. It is concluded that the de-icing of airplane wings by heat from engine exhaust shows sufficient promise to warrant full-scale tests. For propellers, at least, and possibly for certain small areas such as windshields, radio masts, etc. the use of de-icing or adhesion-preventing liquids will provide the best means of protection.

Description: The effect of the existing turbulence in the full scale tunnel was determined from measurements of the profile drag of an N-22 section by the momentum method under corresponding conditions in flight and the tunnel. The transition-point location on the upper surface of the air-foil was also determined from velocity surveys in the boundary layer. The measurements were made at section lift coefficients from 0.480 to 0.635 with a range of Reynolds Numbers from 4,600,000 to 3,900,000. The results show that the end of transition occurs at approximately the same point on the airfoil in flight and in the tunnel. The transition region was somewhat broader in the tunnel and started farther forward than in flight. The laminar profiles in the tunnel had some characteristics of transition profiles in the tunnel and had a much steeper slope near the surface than did the laminar profiles obtained in flight. These differences, however, caused an increase of only 0.0001 in the profile-drag coefficients, as determined by the momentum method.

Description: This note is concerned with the effect of power on landing speed and apparent maximum lift coefficient. It is shown that when secondary effects are neglected, the maximum available increase in lift due to power is equal to the thrust being developed. If the increase in lift due to power is expressed in coefficient form, very high values may be shown under conditions which, on analysis, are found to be wholly impracticable in flight.

Description: The analysis of various types of shell under combined bending and torsion is discussed. The calculation and the use of the shear center are touched upon as incidental problems. Twelve fully worked numerical examples are given in an appendix.

Description: A resume of the generally available test data regarding air loads on slats and flaps is presented and data attained up to the fall of 1938 are included. The data are given in the form of N.A.C.A. standard coefficients of air forces and moments on the lift-increasing device and, when available, the aerodynamic characteristics of the combined wing and high-lift device are included. Slats of the Handley Page type, fixed auxiliary airfoils, and flaps of several different types are covered.

Description: Charts are presented for the coefficients in formulas for the critical compressive stress at which cross-sectional distortion begins in a thin-wall member with either a channel section or a Z-section with identical flanges. The energy method of Timoshenko was used in the theoretical calculations required for the construction of the charts. The deflection equations were carefully selected to give good accuracy. The calculation of the critical compressive stress at stresses beyond the elastic range is briefly discussed. In order to demonstrate the use of the formulas and the charts in engineering calculations, two illustrative problems are included.

Description: Tests of 2-blade, adjustable-pitch, counter rotating tandem model propellers, adjusted to absorb equal power at maximum efficiency, were made at Stanford University. The characteristics, for 15 degrees, 25 degrees, 35 degrees, and 45 degrees pitch settings at 0.75 R of the forward propeller and for 8-1/2 percent, 15 percent, and 30 percent diameter spacings, were compared with those of 2-blade and 4-blade propellers of the same blade form. The tests showed that the efficiency of the tandem propellers was from 0.5 percent to 4 percent greater than that of a 4-blade propeller and, at the high blade-angle settings, not appreciably inferior to that of a 2-blade propeller. It was found that the rear tandem propeller should be set at a blade angle slightly less than that of the forward propeller to realize the condition of equal power at maximum efficiency. Under this condition the total power absorbed by the tandem propellers was from 3 percent to 9 percent more than that absorbed by the 4-blade propeller and about twice that absorbed by a 2-blade propeller.

Description: A monocoque box specimen of aluminum alloy was subjected to end compression and the strains in the stringers were measured up to loads at which permanent set became noticeable. The stringer strains at low loads agreed closely with those computed from the assumption of uniform stress distribution. Buckling of the 0.026-inch sheet between stringers and of the 0.075-inch shear web took place at stresses in accord with theoretical values. Permanent set became noticeable at a load of 115,200 pounds, corresponding to an average stringer stress of about 16,000 pounds per square inch. The measured average strain above the first buckling load was within 2 percent of the theoretical strain as calculated from the dimensions of the box and effective width formulas due to Marguerre and to Cox.

Description: The comparative performance was determined of engines using three methods of mixing the fuel and the air: the use of a carburetor, manifold injection, and cylinder injection. The tests were made of a single-cylinder engine with a Wright 1820-G air-cooled cylinder. Each method of mixing the fuel and the air was investigated over a range of fuel-air ratios from 0.10 to the limit of stable operation and at engine speeds of 1,500 and 1,900 r.p.m. The comparative performance with a fuel-air ratio of 0.08 was investigated for speeds from 1,300 to 1,900 r.p.m. The results show that the power obtained with each method closely followed the volumetric efficiency; the power was therefore the highest with cylinder injection because this method had less manifold restriction. The values of minimum specific fuel consumption obtained with each method of mixing of fuel and air were the same. For the same engine and cooling conditions, the cylinder temperatures are the same regardless of the method used for mixing the fuel and the air.

Description: The loads imposed on intermediate frames by the curvature of the longitudinal and by the diagonal-tension effects are treated. A new empirical method is proposed for analyzing diagonal-tension effects. The basic formulas of the pure diagonal-tension theory are used, and the part of the total shear S carried by diagonal tension is assumed to be given the expression S (sub DT) = S (1-tau sub o/tau)(sup n) where tau (sub o) is the critical shear stress, tau the total (nominal shear stress), and n = 3 - sigma/tau where sigma is the stress in the intermediate frame. Numerical examples illustrate all cases treated.

Description: Charts are presented for the coefficients in the formulas for the critical compressive stress at which cross-sectional distortion begins in thin-wall columns of I-, Z-, channel, and rectangular-tube sections. The energy method of Timoshenko was used in the theoretical calculations required for the construction of the charts. The deflection equations were carefully selected to give good accuracy. The calculation of the critical compressive stress at stresses above the elastic range is briefly discussed in order to demonstrate the use of the formulas and the charts in engineering calculations. Two illustrative problems are included.

Description: The results of flight tests of four nose-slot cowling designs with several variations in each design are presented. The tests were made in the process of developing the nose-slot cowling. The results demonstrate that a nose-slot cowling may be successfully applied to an airplane and that it utilizes the increased slipstream velocity of low-speed operation to produce increased cooling pressure across the engine. A sample design calculation using results from wind-tunnel, flight, and ground tests is given in an appendix to illustrate the design procedure.

Description: Pressure-distribution tests were made on the 32-foot whirling arm of the Daniel Guggenheim Airship Institute of a rectangular wing of NACA 23012 section to determine the rolling and the yawing moment due to angular velocity in yaw. The model was tested at 0 and 5 degree pitch; 0, +/- 5, and +/- 10 degrees yaw; and with no flap and with split flaps 25, 50 and 75 percent of the wing span and deflected 60 degrees. The results are given in the form of span load distributions and as calculated moment coefficients. The experimental values of rolling- and yawing-moment coefficients were in fairly close agreement with theory.

Description: The flow over the inner halves of the rotor blades on a Kellet YG-1B autogiro was investigated in flight by making camera records of the motion of silk streamers attached to the upper surfaces of the blades. These records were analyzed to determine the boundaries of the region within which the flow over the blade sections was stalled for various tip-speed ratios. For the sake of comparison, corresponding theoretical boundaries were obtained. Both the size of the stalled area and its rate of growth with increasing tip-speed ratio were found to be larger than the theory predicted, although experiment agreed with theory with regard to shape and general location of the stalled area. The stalled region may be an important factor in both the rotor lift-drag ratio and the blade flapping motion at the higher tip-speed ratios. The method of study used in this paper should be useful in further studies of the problem, including the reduction of the size of the region.

Description: A chart is presented for the coefficient in the formula for the critical compressive stress at which cross sectional distortion begins in a thin-wall tube of rectangular section symmetrical about its two principal axes. The energy method of Timoshenko was used in the theoretical calculations required for the construction of the chart. The deflection equation used in this method was selected to give good accuracy. The exact values given by solution of the differential equation were calculated for a number of cases and it was found that the energy solution was correct to within a fraction of 1 percent. The calculation of the critical compressive stress at stresses above the elastic range is also discussed. In order to demonstrate the use of the formulas and the chart in engineering calculations, several illustrative problems are included.

Description: An investigation was made in the N.A.C.A. 7- by 10-foot wind tunnel to determine the aerodynamic characteristics of tapered and rectangular wings with partial-span slotted flaps. Two N.A.C.A. 23012 airfoils equipped with center-section and tip-section flaps were tested. The results showed that the changes in lift and drag due to changes in flap span for both rectangular and tapered wings having partial-span slotted flaps were similar to those for corresponding wings having partial-span split or plain flaps. For the two wings tested, higher values of maximum lift were obtained with center-section slotted flaps than with tip-section slotted flaps of the same size. The highest values of lift-drag ratio at maximum lift for the rectangular wing were obtained with center-section flaps and, for the tapered wing, with tip-section flaps. Center-section flaps on the tapered wing gave higher values of drag at maximum lift than tip-section flaps; no great difference in drag at maximum lift was apparent for either center-section or tip-section slotted flaps on the rectangular wing.

Description: An aluminum-alloy plate containing an open circular hole of diameter large compared with the thickness of the plate was subjected to bending forces normal to the plane of the plate. Deflection and strain measurements were taken for two different loads. Stress concentrations occurred at the edge of the hole and the maximum stresses were tangential to the hole at the ends of the transverse diameter. The maximum stress at the edge of the hole was 1.59 times the computed stress on the net section and 1.85 times the computed stress in a solid plate of the same dimensions subjected to the same bending forces. The maximum deflections were about 20 percent greater than the corresponding deflection for a solid plate of the same size subjected to the same bending forces. The smallest edge distance was equal to 2-1/2 times the diameter of the hole and the stress concentration on this side of the hole was the same as on the side where the edge distance was about 4-1/2 diameters. A theoretical analysis of the problem shows that, for an aluminum plate of infinite width, the stress concentration at the edge of the hole would be 1.87 times the stress in a solid plate, which is substantially the same relation obtained for the plate tested.

Description: The analysis of the bending action in box beams with appreciable shear deformation of the flanges becomes very difficult in the general case of variable cross section and loading. This paper presents a convenient method of solving the problem by the familiar method of dividing the beam into a number of bays that can be assumed to have constant cross section and loading. Application of formerly derived shear-lag formulas leads to a general equation closely analogous in form to the well-known three-moment equation. A numerical example and two comparisons between calculation and experimental results are included.

Description: A method has been developed for making photoelastic analyses of three-dimensional stress systems by utilizing the polarization phenomena associated with the scattering of light. By this method, the maximum shear and the directions of the three principal stresses at any point within a model can be determined, and the two principal stresses at a free-bounding surface can be separately evaluated. Polarized light is projected into the model through a slit so that it illuminates a plane section. The light is continuously analyzed along its path by scattering and the state of stress in the illuminated section is obtained. By means of a series of such sections, the entire stress field may be explored. The method was used to analyze the stress system of a simple beam in bending. The results were found to be in good agreement with those expected from elementary theory.

Description: The problem of developing a windshield for aircraft which will withstand the effect of bird impacts during flight is a difficult one, as an estimate of the striking energy will indicate. If the average speed of the airplane is considered to be about 200 miles per hour and that of the bird about 70 miles per hour, the speed of the bird relative to the airplane may be as great as 400 feet per second. If a 4-pound bird is involved, a maximum impact energy of approximately 10,000 foot-pounds must be dissipated. To obtain this energy in a drop test in the Washington Monument, it would be necessary to drop a 20-pound weight down the 500-foot shaft. For both theoretical and practical reasons, it is necessary to keep the mass and speed more nearly like those to be encountered. However, to get an impact of about 10,000 foot-pounds with a 4-pound falling body, it would be necessary to drop it from a height of approximately one-half mile, neglecting air resistance. These facts will indicate some of the experimental obstacles in the way of simulating bird impacts against aircraft windshields.

Description: Pressure-distribution tests were made on the 32-foot whirling arm of the Daniel Guggenheim Airship Institute of a tapered wing to determine the rolling and the yawing moments due to an angular velocity in yaw. The model was tested at 0 degree and 5 degree pitch; 0 degree, 5 degree, and 10 degree yaw; and with split flaps covering 25, 50, 75, and 100 percent of the wing span and deflected 60 degrees. The results are given in the form of load distributions and as calculated moment coefficients. The experimental values of rolling- and yawing- moment coefficients were in fairly close agreement with theory.

Description: Tidewater and weather-exposure tests on various aluminum alloys, magnesium alloys, and stainless steels are now being conducted by the National Bureau of Standards. Exposures were begun in June 1938 and, according to present plans, are to continue over a 3-year period. The methods of exposure and the materials being investigated are described and the more important results obtained up to the conclusion of the first year's exposure are reported.

Description: Experimental measurements and theoretical calculations were made on an aircraft-type, single cylinder engine, in order to determine the physical nature of the inlet process, especially at high piston speeds. The engine was run at speeds from 1,500 to 2,600 r.p.m. (mean piston speeds of 1,370 to 2,380 feet per minute). Measurements were made of the cylinder pressure during the inlet stroke and of the power output and volumetric efficiency. Measurements were also made, with the engine not running, to determine the resistance and mass of air in the inlet valve port at various crank angles. Results of analysis indicate that mass has an appreciable effect, but friction plays the major part in restricting flow. The observed fact that the volumetric efficiency is considerably less than 100 percent is attributed to thermal effects. An estimate was made of the magnitude of these effects in the present case, and their general nature is discussed.

Description: Pressure-distribution tests of an N.A.C.A. 0009 airfoil with a 50-percent-chord plain flap and three plain tabs, having chords 10, 20, and 30 percent of the flap chord, were made in the N.A.C.A. 4- by 6- foot vertical tunnel. The tests supplied aerodynamic section data that may be applied to the design of horizontal and vertical tail surfaces. The results are presented as resultant-pressure diagrams for the airfoil with the flap and the 20-percent-chord tab. Plots are also given of increments of normal-force and hinge-moment coefficients for the airfoil, the flap, and the three tabs. The experimental results and values computed by analytical methods are in good agreement for small flap and tab deflections. The results of the tests indicated that the effectiveness of all three tab sizes in reducing flap hinge moments decreased with increasing flap deflection.

Description: Thirty-three 24ST aluminum-alloy 2- by 2- by 0.10-inch channels, with lengths ranging from 10 to 90 inches were tested at Stanford University in compression to obtain an experimental verification of the theoretical formulas for torsional failure developed by Eugene E. Lundquist of the N.A.C.A. The observed critical loads and twist-axis locations were sufficiently close to the values obtained from the formulas to establish the substantial validity of the latter. The differences between observed and computed results were small enough to be accounted for by small and mostly unavoidable differences between actual test conditions and those assumed in deriving the formulas. Some data were obtained from the shorter specimens regarding the growth of the buckles that resulted in local buckling failure.

Description: The relations between load on the structure and rotation of a joint can be used to estimate the lowest critical load after the equation for neutral stability has been tested for three assumed critical loads, each of which is less than the lowest critical load. The solutions of six simple problems are included to illustrate the application of the method of estimating critical loads and to reveal certain characteristics of the method that should be known by the practical engineer using it. Four of these problems are concerned with members that lie in the elastic, or long-column, range. The other two problems are concerned with members that lie in the short-column range.

Description: Measurements were made of the circulation about the rectangular tip of a short-span airfoil passing through an artificial gust of known velocity gradient. A Clark Y airfoil of 30-centimeter chord was mounted on a whirling arm and moved at a velocity of 29 meters per second over a vertical gust with a velocity of nearly 7 meters per second. Flow angles were measured with a hot-wire apparatus. The rate at which the lift at the tips of a wing entering a gust is realized was found to be in satisfactory agreement with that predicted on the basis of the two-dimensional theory of von Karman and Sears.

Description: An investigation has been made in the N.A.C.A. 7- by 10-foot wind tunnel of a large-chord N.A.C.A. 23012 airfoil with several arrangements of a 40-percent-chord slotted flap to determine the section aerodynamic characteristics of the airfoil as affected by slot shape, flap location, and flap deflection. The flap positions for maximum lift, the polar for arrangements considered favorable for take-off and climb, and the complete section aerodynamic characteristics for selected optimum arrangements were determined. A discussion is given of the relative merits of the various arrangements. A comparison is made of slotted flaps of different chords on the N.A.C.A. 23012 airfoil. The best 40-percent-chord slotted flap is only slightly superior to the 25-percent-chord slotted flap from considerations of maximum lift coefficient and low drag for take-off and initial climb.

Description: Three models of V-bottom floats for twin-float seaplanes (N.A.C.A. models 57-A, 57-B, and 57-C) having angles of dead rise of 20 degrees, 25 degrees, and thirty degrees, respectively, were tested in the N.A.C.A. tank and in the N.A.C.A. 7- by 10-foot wind tunnel. Within the range investigated, the effect of angle of dead rise on water resistance was found to be negligible at speeds up to and including the hump speed, and water resistance was found to increase with angle of dead rise at planing speeds. The height of the spray at the hump speed decreased with increase in angle of dead rise and the aerodynamic drag increased with dead rise. Lengthening the forebody of model 57-B decreased the water resistance and the spray at speeds below the hump speed. Spray strips provided an effective means for the control of spray with the straight V sections used in the series but considerably increased the aerodynamic drag. Charts for the determination of the water resistance and the static properties of the model with 25 degrees dead rise and for the aerodynamic drag of all the models are included for use in design.

Description: The deformation of two sheet-stringer panels subjected to end compression under carefully controlled end conditions was measured at a number of points and at a number of loads, most of which were above the load at which the sheet had begun to buckle. The two panels were identical except for the sheet, which was 0.70-inch 24st alclad for specimen 1 and 0.025-inch 24st aluminum alloy for specimen 6. A technique was developed for attaching Tuckerman optical strain gauges to the sheet without disturbing the strain distribution in the sheet by the method of attachment. This technique was used to explore the strain distribution in the sheet at various loads. The twisting and the bending of the stringers was measured by means of pointers attached to the stringers. The shape of the buckles in the sheet of specimen 6 was recorded at two loads by means of plaster casts. The sheet and the stringer loads at failure are compared with the corresponding loads for five similar panels tested at the Navy Model Basin. A detailed comparison is made between the measured deformation of the buckled sheet and the deformation calculated from approximate theories for the deformation in a rectangular sheet with freely supported edges buckling under end compression advanced by Timoshenko, Frankland, and Marguerre. The measured effective width for the specimens is compared with the effective width given by nine different relations for effective width as a function of the edge stress divided by the buckling stress of the sheet. The analysis of the measured stringer deformation is confined to an application of Southwell's method of plotting deformation against deformation over load. It was concluded that the stringer failure in both specimens were due to an instability in which the stringer was simultaneously twisted and bent as a column.

Description: A flight investigation was conducted to determine the lateral-control characteristics of retractable ailerons installed on a highly tapered wing. The effectiveness of the ailerons in producing roll was measured at various air speeds with full-span plain flaps both neutral and deflected 45 degrees. The direction of the yawing moment created by the ailerons was also noted. The lateral control provided by the retractable ailerons used in this investigation was approximately the same as that obtained with the plain ailerons of equal span with which the airplane was previously equipped. The amount of control available was found to be somewhat inadequate, apparently because of the rather short span of the ailerons (0.327 of the wing span). It is likely that, with an aileron span of from 0.50 to 0.60 of the wing span, a satisfactory degree of control would be obtained. With the full-span flaps deflected 45 degrees, the rolling action of the ailerons was increased about 30 percent over that obtained with the flaps neutral at the same speed. The yawing moment produced by the ailerons was in the same sense as the rolling moment, i.e., right roll was accompanied by yaw. Lag in the response of the rolling action to control application was not large enough to be noticed by the pilots. No appreciable control force was apparent to the pilots, which was considered somewhat undesirable. Minor modifications in the design of the ailerons, however, would probably correct this fault.

Description: Pressure-distribution tests were made on the 32-foot whirling arm of the Daniel Guggenheim Airship Institute of a tapered wing to determine the rolling and yawing moments due to an angular velocity in yaw. The model was tested at 0 degree and 5 degrees pitch, -1 degree and 5 degree yaw, and with a full-span flap deflected 60 degrees. The results are given in the form of span load distributions and in calculated moment coefficients. The rolling-moment coefficients are in fairly close agreement with those derived by means of a simple approximate theory even for high deflection of the full-span flap.

Description: Optimum proportions of tapered wings were investigated by a method that involved a comparison of wings designed to be aerodynamically equal. The conditions of aerodynamic equality were equality in stalling speed, in induced drag at a low speed, and in the total drag at cruising speed. After the wings were adjusted to aerodynamic equivalence, the weights of the wings were calculated as a convenient method of indicating the optimum wing. The aerodynamic characteristics were calculated from wing theory and test data for the airfoil sections. Various combinations of washout, camber increase in the airfoil sections from the center to the tips, and sharp leading edges at the center were used to bring about the desired equivalence of maximum lift and center-stalling characteristics. In the calculation of the weights of the wings, a simple type of spar structure was assumed that permitted an integration across the span to determine the web and the flange weights. The covering and the remaining weight were taken in proportion to the wing area. The total weights showed the wings with camber and washout to have the lowest weights and indicated the minimum for wings with a taper ratio between 1/2 and 1/3.

Description: Unsteady lift function for wings of finite aspect ratio have been calculated by approximate methods involving corrections of the aerodynamic inertia and of the angle of the infinite wing. The starting lift of the finite wing is found to be only slightly less than that of the infinite wing; whereas the final lift may be considerably less. The calculations indicate that the distribution of lift near the start is similar to the final distribution. Both the indicia and the oscillating lift functions are given. Approximate operational equivalents of the functions have been devised to facilitate the calculation of lift under various conditions of motion.

Description: A quantitative criterion of merit has been needed to assist airplane designers to incorporate satisfactory spinning characteristics into new designs. An approximate empirical criterion, based on the projected side area and the mass distribution of the airplane, has been formulated in a recent British report. In the present paper, the British results have been analyzed and applied to American designs. A simpler design criterion based solely on the type and the dimensions of the tail, has been developed: it is useful in a rapid estimation of whether a new design is likely to comply with the minimum requirements for safety in spinning.

Description: An investigation was made in the N.A.C.A. ice tunnel at air temperatures from 20 degrees to 28 degrees Fahrenheit and at a velocity of 80 miles per hour to determine whether ice formations on a model wing could be prevented by the use of the heat from the engine-exhaust gas. Various spanwise duct systems were tested in a 6-foot-chord N.A.C.A. 23012 wing model. The formation of ice over the entire wing chord was prevented by the direct heating of the forward 10 percent of the wing by hot air, which was passed through leading-edge ducts. Under dry conditions, enough heat to maintain the temperature of the forward 10 percent of the wing at about 200 degrees Fahrenheit above that of the ambient air was required for the prevention of ice formation. The air temperature in the ducts that was necessary to produce these skin temperatures varied from 360 degrees to 834 degrees Fahrenheit; the corresponding air velocities in the duct were 152 and 45 feet per second. Ice formations at the leading edge were locally prevented by air that passed over the interior of the wing surface at a velocity of 30 feet per second and a temperature of 122 degrees Fahrenheit.

Description: Ignition-lag data have been obtained for seven fuels injected into heated, compressed air under conditions simulating those in a compression-ignition engine. The results of the bomb tests have been compared with similar engine data, and the differences between the two sets of results are explained in terms of the response of each fuel to variations in air density and temperature.

Description: A method is presented for the rapid calculation of the pressure distribution over an airfoil section when the normal-force distribution and the pressure distribution over the "base profile" (i.e., the profile of the same airfoil were the camber line straight and the resulting airfoil at zero angle of attack) are known. This note is intended as a supplement to N.A.C.A. Report Nos. 631 and 634 wherein methods are presented for the calculation of the normal-force distribution over plain and flapped airfoils, respectively, but not of the pressures on the individual surfaces. Base-profile pressure-coefficient distributions for the usual N.A.C.A. family of airfoils, which are also suitable for several other commonly employed airfoils, are included in tabular form. With these tabulated base-profile pressures and the computed normal-force distributions, pressure distributions adequate for most engineering purposes can be obtained.

Description: Several fuel oils, doped fuel oils, and mixtures of alcohol and fuel oil were tested in a high-speed, single-cylinder, compression-ignition engine to determine power output, fuel consumption, and ignition and combustion characteristics. Fuel oils or doped fuel oils of high octane number had shorter ignition lags, lower rates of pressure rise, and gave smoother engine operation than fuel oils or doped fuel oils of low octane number. Higher engine rotative speeds and boost pressures resulted in smoother engine operation and permitted the use of fuel oils of relatively low octane number. Although the addition of a dope to a fuel oil decreased the ignition lag and the rate of pressure rise, the ensuing rate of combustion was somewhat slower than for the undoped fuel oil so that the effectiveness of combustion was practically unchanged. Alcohol used as an auxiliary fuel, either as a mixture or by separate injection, increased the rates of pressure rise and induced roughness. In general, the power output decreased as the proportion of alcohol increased and, below maximum power, varied with the heating value of the total fuel charge.

Description: An investigation was conducted in the N.A.C.A. 7- by 10-foot wind tunnel to determine the effect of ground proximity on the aerodynamic characteristics of wings equipped with high-lift devices. A rectangular and a tapered wing were tested without flaps, with a split flap, and with a slotted flap. The ground was represented by a flat plate, completely spanning the tunnel and extending a considerable distance ahead and back of the model. The position of the plate was varied from one-half to three chord lengths below the wing. The results are presented in the form of curves of absolute coefficients, showing the effect of the ground on each wing arrangement. The effect of the ground on lift, drag, and pitching moment is discussed. An appendix gives equations for calculating tunnel-wall corrections to be applied to ground-effect tests conducted in rectangular tunnels when a plate is used to represent the ground. The tests indicated that the ground effect on wings with flaps is a marked decrease in drag, a decrease in diving moment, and a substantial reduction in maximum lift.

Description: The analysis of box beams with shear deformation of the flanges can be reduced to the solution of a differential equation. The same equation is met in other problems of stress analysis. No analytical solutions of this equation can be given for practical cases, and numerical methods of evaluation must be used. Available methods are briefly discussed. Two numerical examples show the application of the step-by-step method of integration to shear-lag problems.