ALBERT

Description: No abstract available

Description: No abstract available

Description: The hazards of lightning strokes to aircraft fuel tanks have been investigated in artificial-lightning-generation facilities specifically constructed to duplicate closely the natural lightning discharges to air craft determined through flight research programs and analysis of lightning-damaged aircraft over a period of many years. Explosion studies were made in an environmental explosion chamber using small fuel tanks under various simulated flight conditions. The results showed that there is a primary hazard whenever there is direct puncture of the fuel-tank wall, whereas the ignition of fuel by hot spots on tank walls due to lightning strikes is unlikely. Punctures of fuel-tank walls by artificial-lightning discharges produced explosions of the fuel in the mixture range from excessively lean to rich mixtures. None of the aluminum alloys, 0.081 inch thick or over, were punctured by the laboratory discharges representative of natural-lightning discharges to aircraft; however, reliance on this wall thickness for complete protection would not be justified, because occasional strokes are known to be of greater magnitude and because statistics reveal variations in the damage pattern. Data gathered by the Lightning and Transients Research Institute on lightning strokes to aircraft show that 90 percent of the strokes recorded have occurred in the temperature range of -10 to +10 C, where many of the jet fuels are flammable but where aviation gasoline is overrich. Also, 10 percent of the strokes recorded have been to the wings, which are the principal fuel-storage areas for modern aircraft. Thus, there is a hazard, particularly for jet fuels. Certain protective measures are indicated by the studies to date, such as the use of lightning diverter rods, thickening of the wing skin in areas near the most probable stroke paths, and the use of fuel-tank liners in critical areas.

Description: An investigation has been made of the effect of aerodynamic heating on propeller-blade temperatures. The blade temperature rise resulting from aerodynamic heating was measured and the relation between the resulting blade temperatures and the outer limit of the iced-over region was examined. It was found that the outermost station at which ice formed on a propeller blade was determined by the blade temperature rise resulting from the aerodynamic heating at that point.

Description: Force tests were made of a 1/8-scale model of a twin-engine low-wing transport airplane in the NACA 8-foot high-speed wind tunnel to investigate compressibility and interference effects at speeds up to 450 miles per hour. In addition to tests of the standard arrangement of the model tests were made with several modifications designed to reduce the drag and to increase the critical speed. The results show serious increases in drag at critical speeds below 450 miles per hour due to the occurrence of compressibility burbles on the standard radial-engine cowlings, on sections of the wing as a result of wing-nacelle interference, and on the semi-retracted main landing wheels. The critical speed at which the shock occurred on the standard cowlings was 20 miles per hour lower in the presence of the fuselage than in the presence of the wing only. The drag of the complete model was reduced 25% at 300 miles per hour by completely retracting the landing gear, fairing the windshield irregularities, and substituting streamline nacelles (with allowance made for the proper amount of cooling-air flow) for the standard nacelle arrangement. The values of the critical Mach number were extended from 0.47 to 0.60 as a result of the aforementioned improvements. The principal purpose of the reported tests was to investigate the effect of compressibility on the drag of the component parts of a representative large airplane and on the overall drag of such an airplane. The influence of interference on compressibility effects was also studied. In addition, it was proposed to test several modifications of the standard component parts that gave promise of an improvement in aerodynamic characteristics.

Description: On August 12, 1960, an X-15 flight was made to achieve essentially the maximum altitude expected to be possible with the interim rocket engines. N l y corrected altitude measurements showed that the maxhum geometric altitude was 136,500 feet k600 and the maximum pressure altitude, referred to the tables of the 0. S . Extension to the ICAO Standard Atmosphere, was indicated to be 133,900 feet.

Description: An investigation has been conducted in the Langley 4- by 4-foot supersonic pressure tunnel to determine the aerodynamic characteristics in pitch of a two-stage-rocket model configuration which simulated the last two stages of the launching vehicle for an inflatable sphere. Tests were made through an angle-of-attack range from -6 deg to 18 deg at dynamic pressures of 102 and 255 pounds per square foot with corresponding Mach numbers of 1.89 and 1.98 for the model both with and without a bumper arrangement designed to protect the rocket casing from the outer shell of the vehicle.

Description: An investigation was made in the Langley 300-MPH 7- by 10-foot tunnel with a conventional ground-board setup and in the Langley tank no. 1 by using the tow carriage to move the model over a ground board to evaluate the simulation of flight conditions in ground influence with a conventional ground-board setup. The 12-percent-thick airfoil was unswept and untapered with an aspect ratio of 6.0 and had a 10 percent- chord jet-augmented flap. From this investigation it appears that the loss in lift of an airfoil with a jet-augmented flap in ground influence as determined in a wind tunnel with a conventional ground-board setup is considerably larger than would be obtained in free flight.

Description: Wind-tunnel tests have been conducted on a large-scale model of a swept-wing jet transport type airplane to study the factors affecting exhaust gas ingestion into the engine inlets when thrust reversal is used during ground roll. The model was equipped with four small jet engines mounted in nacelles beneath the wing. The tests included studies of both cascade and target type reversers. The data obtained included the free-stream velocity at the occurrence of exhaust gas ingestion in the outboard engine and the increment of drag due to thrust reversal for various modifications of thrust reverser configuration. Motion picture films of smoke flow studies were also obtained to supplement the data. The results show that the free-stream velocity at which ingestion occurred in the outboard engines could be reduced considerably, by simple modifications to the reversers, without reducing the effective drag due to reversed thrust.

Description: An investigation has been made to determine the thrust characteristics within ground proximity of a series of models which might represent vertical take-off-and-landing (VTOL) aircraft with multiple exit jet engines exhausting vertically downward beneath a lifting surface. Variations in simulated engine configurations were provided by a series of nozzle insert plugs in which the number of jet exits, located symmetrically on a fixed circle, was varied, or the diameter of the circle was varied for a given number of jet exits. represent lifting surfaces, and high-pressure air was used to simulate jet-engine exhaust. Plywood plates were used to The results of the investigation showed that increasing the number of exits, such that an annular jet configuration was approached, provided more favorable thrust characteristics within ground proximity than any other variation in the geometry of these multiple jets. Tests of a configuration with two nozzles approximating a fan-in-wing VTOL aircraft with fans located at different spanwise locations indicated that the augmentation in thrust within ground proximity was greater for the arrangement with the more inboard location of the nozzles.