ALBERT

Notes: The paper presents a straightforward method of calculating approximate orientation parameters (six degrees of freedom) of a known targeted object relative to a single calibrated camera. These can then initialise an optimised non-linear calculation of the same parameter values. The method uses the mathematics of a scaled parallel projection and is particularly suited to narrow angle images obtained using a telescope, telephoto or zoom lens. However, the method can also be used with cameras having wider fields of view provided the target group occupies a moderately small part of the image.

Notes: This paper describes three mathematical modelling methods for high-resolution declassified CORONA KH-4B images. Since CORONA images are collected with a panoramic camera, several types of geometric distortions are involved. Two methods use the modified collinearity equations, and the third involves the terrain-dependent rational function model (RFM) which is considered to be a generic sensor model. Comparative analysis of the three mathematical modelling methods is undertaken. The results show that a ± 1·5 pixels level of horizontal and vertical accuracy can be obtained. A digital elevation model (DEM) of a test site is also created.

Notes: Digital photogrammetry and softcopy workstations have added a new dimension to aerial triangulation, and some of the previously manual procedures are now available in automated form. Also, commercial software packages for automatic aerial triangulation came on to the market in the last decade. In this study, the results of automatic aerial triangulation using four triangulation software packages, Z/I Imaging's MATCH-AT (ISMAT) and ISAT, LH Systems’ MST and VirtuoZo AAT, are presented. For the comparison of the results of the tie point extraction and the bundle block adjustment for triangulation, a sub-block from the Uster block in Switzerland was selected and used. Differences between these software packages are discussed with respect to their functionality and performance in detail. The achieved standard deviation of image coordinates varies between 0·2 and 0·5 pixel for the systems tested. The more signalised control points and check points to be used, the better the σ0 estimate which could be expected. The average number of extracted tie points varied from system to system with respect to the matching method and the resolution of the images used in the programs. The digital aerial triangulation of the Uster sub-block was faster than analytical triangulation and the elapsed time for triangulation of one image using different systems varies between about 0·5 and 6 min. Nevertheless, results also show that automated aerial triangulation is still prone to error in all systems. Image matching produces many blunders, which can only be handled efficiently by using a sophisticated blunder detection procedure, as is available with robust estimation. This is not the case for all the systems tested, however. There still remains a lot to be done in terms of development (improvement of matching, for example, by integrating robust estimation for error detection at an early stage, implementation of on-line triangulation, better internal quality control procedures, more transparent and simple user interfaces and more useful information for the user with better software manuals). However, it was shown that automatic aerial triangulation provides higher redundancy and reliability of results and much more economical photogrammetric practice than ever before.

Notes: 18th International Symposium of Cipa by D. M. Barber, p.50548th Photogrammetric Week by A. T. Smart, p.5065th Conference on Optical 3D Measurement Techniques by G. Hunter, p.509

Notes: Earth observation satellites with 1m resolution, such as Space Imaging's Ikonos system, offer the photogrammetric and remote sensing communities a significant new means for geospatial information collection. These satellites possess the potential for pixel-level geopositioning precision and promise timely, highly automated generation of two dimensional (2D) and three dimensional (3D) spatial information products. This paper concentrates on the pursuit of optimal accuracy and considers an essential first step in the evaluation of the Ikonos imaging system, namely the metric integrity of the sensor system. In the absence of sensor calibration information (the camera model), an empirical evaluation approach has been adopted. This involves an assessment of 2D transformations between image and planar object space. It is shown that based on results obtained in the Melbourne Ikonos Testfield, 2D geopositioning to 0.5 m accuracy is possible from the base-level “Geo”product when a modest amount of good quality ground control is available and sub-pixel image mensuration is achieved. These findings are applicable to both near-nadir imagery and oblique stereo images. Moreover, the results obtained suggest that there are no significant geometric perturbations in the sensor system and initial image processing, which augurs well for the successful application of non-collinearity based 3D orientation and triangulation models for Ikonos imagery.

Notes: The Photogrammetric Society was formed in 1952. The Council of the Society considered that the twentieth anniversary was a good point at which to record the events which led to its formation and the significant occasions and decisions which have taken place since 1952. Consequently, Paul Lamboit was invited to compile this History. He has placed the birth and development of the Society within the national and international photogrammetric context and his record of the deliberations which took place between 1947 and 1952 will be of particular interest to historians of our subject.This account was first published in a limited edition in 1971. Sufficient interest has since been expressed to prompt a wider circulation through publication in the Photogrammetric Record.The author served the Society continuously in several official capacities from 1953 to 1969 and he was elected to Honorary Membership in 1969.〈section xml:id="abs1-2"〉〈title type="main"〉RésuméLa Photogrammetric Society a été fondée en 1952. Excellente occasion pour faire le point qu'un vingtiéme anniversaire, a estimé le Conseil de la Société; pour rappeler les circonstances de sa naissance, les étapes de sa croissance et les décisions importantes prises depuis 1952. Ce qu'on invita Paul Lamboit à faire. Son exposé resitue la naissance et le développement de la Société dans le contexte national et international de la photogrammétrie; la relation qu'il fait des décisions prises entre 1947 et 1952 intéressera particulièrement ceux qui s'occupent d'histoire de la photogrammétrie.Ce rapport d'abord publié en édition limitée en 1971, a suscité un intérêt suffisant pour que l'on se presse en le publiant dans le Photogrammetric Record de le porter à la connaissance d'un plus large public.L'auteur a exercé différentes fonctions de 1953 à 1969 dans l'appareil de la Société. Il a étéélu membre honoraire en 1969.〈section xml:id="abs1-3"〉〈title type="main"〉Zusummenfussung1952 wurde die Britische Gesellschaft für Photogrammetrie gegründet. Der Rat der Gesellschaft erwog, dass der zwanzigste Jahrestag eine günstige Gelegenheit sei, um die Ereignisse, die zur Gründung der Gesellschaft führten sowie die bedeutenden Veranstaltungen, die stattfanden und die Entscheidungen, die getroffen wurden, darzustellen. Aus diesem Grunde wurde Paul Lamboit eingeladen, diesen historischen Rückblick zu schreiben. Er hat dabei die Gründung und die Entwicklung der Gesellschaft in den nationalen und internationalen photogrammetrischen Zusammenhang gestellt nd sein Bericht über die zwischen 1947 und 1972 erfolgten Beratungen wird für an unserer Sache interessierte Historiker sehr aufschlussreich sein.Diese Zusammenstellung wurde erstmals in einer begrenzten Auflage im Jahre 1971 veröffentlicht. Genügend Interesse wurde inzwischen bekundet, um eine weitergehende Verteilung mit Hilfe des Photogrammetric Record zu veranlassen.Der Autor diente der Gesellschaft kontinuierlich in verschiedenen Ämtern von 1953 bis 1969, wo er aum Ehrenmitglied gewählt wurde.

Notes: The paper traces the history of the Wild series of rectifiers, paying particular attention to the mechanical solutions of the Newton and Scheimpflug conditions.

Notes: This paper gives a summary of the methods that have been used for independent model aerial triangulation. A modification of one of the methods is proposed and the paper concludes with a comparison of the independent model with the classical method of triangulation.

Notes: The camera is a further development of an existing type with greatly improved photogrammetric performance so that the photography can be used with first-order plotting machines. A new lens provides minimal distortion, high resolution and greatly improved marginal illumination. An entirely new shutter provides high speeds and efficiency. Laboratory results and preliminary survey trials indicate image quality and location standards of the same order as established existing cameras.

Notes: Book reviews in this article:INTERNATIONAL YEAR BOOK OF CARTOGRAPHY (Vol. IV, 1964). Editor, Eduard Imhof.JUBILEE VOLUME DEDICATED TO WILLEM SCHERMERHORN ON HIS SEVENTIETH ANNIVERSARY: ESSAYS ON THE DEVELOPMENT OF PHOTOGRAMMETRY. Published by I.T.C., Delft.

Notes: This paper introduces the subject of digital sensors for aerial survey by reviewing the use made of small format digital cameras in such an application. The major advantages and disadvantages of employing such consumer technology for aerial survey are highlighted. Finally, a specification is proposed for a minimum requirement for a digital solution based on a single area array sensor.

Notes: Joint development work by LH Systems and Deutsches Zentrum für Luft- und Raumfahrt (German Aerospace Center) has produced encouraging results using forward, nadir and backward looking linear arrays on the focal plane to provide panchromatic imagery and geometric information, supplemented by further arrays to acquire multispectral imagery suitable for both high precision photogrammetric mapping and image processing for interpretative purposes. The geometric characteristics of line scanner imagery necessitate line-by-line rectification for aircraft tilts and shifts. Satisfactory execution of this process is enhanced by using supplementary data from high performance, on-board GPS and inertial measurement systems. Similarly, high demands are placed on other sub-systems, such as the camera mount, lens, electronics and storage technology. In addition to rectification for aircraft tilts and shifts, rectification for terrain characteristics is also required in order to generate colour and false colour composite images, since the various multispectral arrays are in different places on the focal plane. The special geometry affects triangulation. Thereafter, the imagery can be processed using existing software packages from both photogrammetry and remote sensing.The concept has been demonstrated in several successful test flights and the production model is scheduled for market introduction at the ISPRS Congress in July 2000. The imagery from the new sensor will fulfil many market requirements between the highest resolution film imagery (〈0.1 m) and high resolution space imagery (1m to 10 m). The sensor's unique blend of multispectral information with high quality geometric information will give rise to numerous new applications.

Notes: Market needs for airborne and spaceborne imagery used in photogrammetry and GIS applications are changing. Fundamental changes in sensors, platforms and applications are currently taking place. Most recently, new high resolution spaceborne sensors have become available. Besides classical photogrammetry, new thematic applications will drive the future image market. Savings in cost and time, together with the need for higher and reproducible radiometric resolution or spectral information will push forward the change from analogue to digital imagery. High resolution satellites will compete with airborne film-based photography and digital camera systems.With the availability of a digital airborne camera, it is possible to completely close the digital chain from image acquisition to exploitation and data distribution. The key decision regarding the camera design in this case is whether a linear or area array sensor should be used. In view of the high geometric accuracy requirements in photogrammetry, Z/I Imaging has focused development on a digital camera based on an area sensor. An essential aspect of this decision was not only the aerial camera system, but also the entire photogrammetric process to the finished photographic or mapping product. If this point of view is adopted, it becomes clear that the development of a digital camera involves more than simply exchanging film for silicon. Aspects such as data transfer rates, in-flight data processing and storage, image archiving, georeferencing, colour fusion, calibration and preprocessing have the same influence on the economic assessment of a digital camera system. This paper describes current development activities and application aspects of a digital modular airborne camera system.

Notes: Architecture at the Maya archaeological site of Uxmal in Yucatan, Mexico has been documented since the 17th century by historians, archaeologists, illustrators, photographers, and most recently photogrammetrists. This paper reviews the work of the major contributors to recording of architecture at Uxmal with a particular focus on the 19th century stereophotography of Alice and Augustus Le Plongeon who worked to record all the standing architecture at Uxmal, and the close range stereophotogrammetric projects that recorded the Adivino Pyramid during the late 20th century.

Notes: This article presents a complete mathematical model, which translates discrepancies between two orthophotographs created from different photographs, into precise corrections of the Digital Elevation Model (DEM). These corrections are the differences from the real surface and, if applied over the existing DEM, can produce a more accurate one. The mathematical model is straightforward, and is not approximate, and therefore there is no need for iterations.Possible applications include checking of automatically created DEMs, refinement of existing DEMs using aerial photographs and update of orthophotographs based on the previous DEM and new imagery.

Notes: Lidar and photogrammetry have both been evaluated for detecting shortterm coastal change using the Black Ven mudslide, Dorset as a case study. A lidar-generated digital elevation model (DEM) was obtained and initially compared with a DEM generated using available 1:7500 scale aerial photography and automated digital photogrammetry. The quality of these two data sets was assessed using a third DEM, derived using a total station and conventional ground survey methods. The vertical accuracies (rms error) of the lidar and photogrammetry were 0.26m and 0.43m respectively, although both data sets displayed a tendency to generate heights slightly lower than the elevation of the terrain surface. The quality of the two data sets was then assessed with respect to local slope angle. The accuracy of photogrammetrically derived elevations varied with slope and more so than in the case of lidarFrom these basic tests, lidar has proved to be more accurate than photogrammetry for soft-cliff. monitoring. Further research is required to establish whether this trend is applicable to other data sets and specifically for photogrammetric data acquired using larger scale imagery

Notes: Research into both extraction of man-made objects and automatic change detection from aerial and satellite images has made significant progress in recent years. This paper presents an approach, based on a fuzzy logic system, for the identification of suburban roads in Ikonos images. The linguistic variables are the mean and standard deviation (SD) of different objects with Gaussian membership function. After the roads have been identified provisionally and their skeleton extracted, the skeleton can be vectorised and then used as direct input to a GIS for further analysis. The method was tested on an Ikonos “Geo” image covering Bilesavar in north-western Iran. For the suburban area of Bilesavar, the results showed that grey scale values ranged from 20 to 190 for non-roads and 226 to 228 for roads, the optimum width of the Gaussian kernel function was 3 and the SD was 0.4. It was also found that about 91% of main roads with a width of 6 to 12 pixels could be extracted from high resolution satellite imagery by the algorithm. The computer program for this study has been developed in visual C++ based on Windows 98

Notes: Books reviewed:S. Openshaw and R. J. Abrahart, GeocomputationM. Craglia and H. Onsrud, Geographic Information Research: Transatlantic PerspectivesP. J. Halls, Spatial Information and the EnvironmentJ. Sievers and T. Schneider, Second International Symposium on Geographical Names: Geonames 2000J. C. Leachtenauer and R. G. Driggers, Surveillance and Reconnaissance Imaging Systems: Modelling and Performance PredictionP. A. Longley, M. F. Goodchild, D. J. Maguire and D. W. Rhind, Geographic Information Systems and ScienceY. Q. Chen and Y. C. Lee, Geographical Data AcquisitionK. Borre, Plane Networks and their Applications.A. Hirschfield and K. Bowers, Mapping and Analysing Crime Data: Lessons from Research and PracticeO. Koelbl, Proceedings of the Oeepe Workshop on Automation in Digital Photogrammetric ProductionRICS Books, Vertical Aerial Photography and Derived Digital Imagery: Client Specification GuidelinesD. E. Reeve and J. R. Petch, Gis Organisations and People: A Socio-Technical Approach

Notes: The research described in this paper is part of a Swiss National Science Foundation project on ”Mass Balance Determination of Glaciers with the Use of State-of-the-art Remote Sensing Methods and a Numerical Flow Model”. The remote sensing methods involve automated processing of aerial images and laser scanning and aim to produce glacier surface models with an accuracy of about 0.5 to 1m over time periods of 1 to 5 years. The Unteraar glacier, in Switzerland, has been chosen to test both methods, because it has been extensively studied by glaciologists. The results from laser scanning and digital photogrammetry were evaluated by comparison with accurate manual measurements from an analytical plotter. Various aspects of the laser data processing are discussed, such as system description, position and attitude determination, transformation to the Swiss map coordinate system, fit of overlapping laser strips and problems encountered. Three digital photogrammetric systems (Match-T, LHS DPW770 and VirtuoZo) were used for surface model generation using image matching. The different matching algorithms and strategies, the matching problems that occurred, for example, due to low texture, shadows, or steep slopes, and a quantitative and qualitative evaluation of the results are presented. Finally, a comparison is given between photogrammetry and laser scanning regarding accuracy and point density.

Notes: Many photogrammetric and GIS applications, such as city modelling, change detection and object recognition, deal with surfaces. Change detection involves looking for differences between two surface models that are obtained from different sensors, for example an optical sensor and a laser scanner, or by the same sensor at different epochs. Surfaces obtained through a sampling process may also have to be compared for future processing (for example transformation parameter estimation and change detection). Surface matching is therefore an essential task in these applications. The matching of surfaces involves two steps. The first step deals with finding the correspondences between two surface points and/or patches. The second step requires the determination of transformation parameters between the two surfaces. However, since most surfaces consist of randomly distributed discrete points and may have different reference systems, finding the correspondences cannot be achieved without knowing the transformation parameters between the two surfaces. Conversely, deriving the transformation parameters requires the knowledge of the correspondence between the two point sets. The suggested approach for surface matching deals with randomly distributed data sets without the need for error prone interpolation and requires no point-to-point correspondence between the two surfaces under consideration. This research simultaneously solves for the correspondence and the transformation parameters using a Modified Iterated Hough Transform for robust parameter estimation. Several experiments are conducted to prove the feasibility and the robustness of the suggested approach, even when a high percentage of change exists.

Notes: It is well recognised that data volume represents a huge overhead for softcopy photogrammetry. For example, a file size of 100 Mbytes will be generated from a black and white aerial photograph if digitised with a resolution of 20μm. Large data volumes not only create storage problems but also affect the speed of image processing. As a consequence, data compression of image data is a matter of great significance. This paper describes an investigation into the effects of image compression on the accuracy of digital terrain models (DTMs) extracted from the compressed images. The JPEG system implemented in the Z/I Imaging ImageStation digital photogrammetric workstation (DPW) was used in the study. A systematic test has been carried out on the effect of different levels of JPEG compression (with Q-factors from 1 to 100) on the resulting DTM, which is automatically generated by the DPW using Match-T software. An analysis of the results from the two sites tested shows that image compression tends to cause more significant degradation when the image texture is richer, but that recommendations on Q-factors for use with the ImageStation appear to err on the side of caution. This analysis leads to some tentative conclusions and recommendations both for future investigation and for photogrammetric practice.

Notes: This paper describes an approach to single image automatic orientation and point determination by using current ortho-images and a DTM, and the experience gained in its implementation. The procedure proposed automatically extracts and matches feature points in evenly distributed patches on aerial images and ortho-images. A large number of image measurements (up to several thousand) are obtained in this process and are included in a robust space resection to determine the orientation parameters of the aerial image. For point determination with a single image, a method is formalised which integrates the DTM interpolation into the space resection so that the 3D ground coordinates of the image points can be determined in a unified mathematical model. Tests and analyses of this method show that the large number of automatic image measurements relieves the requirement for complicated and precise feature extraction and matching methods. The ground points obtained from single image intersection have an accuracy of approximately 1 pixel in planimetry, which fulfils the requirement for ortho-image updating. The elevation accuracy is mainly dependent on the quality of the current DTM and the interpolation method applied to it.

Notes: For the conservation of historic monuments, there may be considerable value in automating the methods of detection and analysis of surface condition and deterioration. This paper describes tests using a range of multiband and multispectral images for the assessment of architectural façade cover by means of supervised image classifications. From the spectral training sets, both pairwise distances (the Euclidean distance and the Jeffries-Matusita (J-M) distance) are calculated and are used to predict the a posteriori accuracy of image classification. Furthermore, the effects of increasing the number of spectral bands (blue, green, red and near-infrared) in the supervised maximum-likelihood classification procedures are also analysed, as are the benefits of applying principal components. The resultant multiband datasets increased both the J-M distance and the classification accuracy of the architectural façade, and thus enabled better identification and recognition of the different kinds of façade-cover features.

Notes: The XIXth International Congress of Photogrammetry and Remote Sensing was held at the Amsterdam RAI International Exhibition and Congress Centre, the Netherlands, from 16th to 23rd July 2000. Reports are given on the Congress as a whole, including the General Assembly, some Technical Commission activities and the Congress Exhibition. Papers from the Congress are published in the International Archives of Photogrammetry and Remote Sensing, 33.

Notes: A scholarly account of the formative discussions, the founding and the first 20 years of the Photogrammetric Society was published in 1971 and republished in 1974. This present review concentrates on the latter years of the life of the Photogrammetric Society prior to its merger with the Remote Sensing Society in 2001.The authors joined the Photogrammetric Society in 1960 and were conspicuous in its affairs for many years. Although both occupied the Society's presidential chair, they also fulfilled several other roles in its efficient management. Atkinson's first contribution to the Photogrammetric Record was published in 1968 and Newton's in 1971.

Notes: The Photogrammetric Society was formed in 1952. The Council of the Society considered that the twentieth anniversary was a good point at which to record the events which led to its formation and the significant occasions and decisions which have taken place since 1952. Consequently, Paul Lamboit was invited to compile this History. He has placed the birth and development of the society within the national and international photogrammetric context and his record of the deliberations which took place between 1947 and 1952 will be of particular interest to historians of our subject.This account was first published in a limited edition in 1971. Sufficient interest has since been expressed to prompt a wider circulation through publication in the Photogrammetric Record.The author served the Society continuously in several official capacities from 1953 to 1969 and he was elected to Honorary Membership in 1969.

Notes: Increased use of digital imagery has facilitated the opportunity to use features, in addition to points, in photogrammetric applications. Straight lines are often present in object space, and prior research has focused on incorporating straight–line constraints into bundle adjustment for frame imagery. In the research reported in this paper, object–space straight lines are used in a bundle adjustment with self–calibration. The perspective projection of straight lines in the object space produces straight lines in the image space in the absence of distortions. Any deviations from straightness in the image space are attributed to various distortion sources, such as radial and decentric lens distortions. Before incorporating straight lines into a bundle adjustment with self–calibration, the representation and perspective transformation of straight lines between image space and object space should be addressed. In this investigation, images of straight lines are represented as a sequence of points along the image line. Also, two points along the object–space straight line are used to represent that line. The perspective relationship between image– and object–space lines is incorporated in a mathematical constraint. The underlying principle in this constraint is that the vector from the perspective centre to an image point on a straight–line feature lies on the plane defined by the perspective centre and the two object points defining the straight line. This constraint has been embedded in a software application for bundle adjustment with self–calibration that can incorporate point as well as straight–line features. Experiments with simulated and real data have proved the feasibility and the efficiency of the algorithm proposed.

Notes: The determination of the attitude, the position and the intrinsic geometric characteristics of the camera is recognised as the fundamental photogrammetric problem. It can be summarised as the determination of camera interior and exterior orientation parameters, as well as the determination of 3D coordinates of object points. The term “exterior orientation”of an image refers to its position and orientation related to an exterior (object space) coordinate system. Several methods can be applied to determine the parameters of the orientation of one, two or more photos. The orientation can be processed in steps (as relative and absolute orientation) but simultaneous methods (such as bundle adjustments) are now available in many software packages. Several methods have also been developed for the orientation of single images. They are based in general on geometric and topological characteristics of imaged objects.This paper presents a survey of classical and modern methods for the determination of the exterior parameters in photogrammetry, some of which are available as software packages (with practical examples) on the Internet. The methods presented are classified in three principal groups. In the first, a selection of approximate methods for applications that do not require great accuracy is presented. Such methods are also used to calculate values required for iterative processes. In the second group, standard point–based methods derived from collinearity, coplanarity or coangularity conditions are briefly reviewed, followed by line–based approaches. The third group represents orientation methods based on constraints and on concepts of projective geometry, which are becoming of increasing interest for photogrammetrists. In the last section, the paper gives a summary of existing strategies for automatic exterior orientation in aerial photogrammetry.

Notes: The geologist's use of air photographs and the characteristics studied by photogeologists are briefly described. The influence of photographic factors such as scale, season, time of day, film type, processing, overlap and dimensional accuracy are considered from the geologist's viewpoint.

Notes: This paper modifies the well-known formula that corrects x-parallaxes for tilt. It shows how we can make significant improvements in accuracy with a no more complicated formula, in which the effects of ground relief are completely removed; and how we can reduce the second-order errors due to lateral (w) tilts by very large factors in favourable cases.

Notes: A scholarly account of the formative discussions, the founding and the first 20 years of the Photogrammetric Society was published in 1971 and republished in 1974. This present review concentrates on the latter years of the life of the Photogrammetric Society prior to its merger with the Remote Sensing Society in 2001.The authors joined the Photogrammetric Society in 1960 and were conspicuous in its affairs for many years. Although both occupied the Society's presidential chair, they also fulfilled several other roles in its efficient management. Atkinson's first contribution to the Photogrammetric Record was published in 1968 and Newton's in 1971.〈section xml:id="abs1-2"〉〈title type="main"〉RésuméOn a publié en 1971 un compte-rendu détaillé des 20 premières années de la “Photogrammetric Society”, à commencer par les discussions qui présidèrent è sa fondation. Ce récit fut republié en 1974. On se focalise dans cet article sur les dernières années d'activité de la “Photogrammetric Society” qui aboutirent à sa fusion avec la “Remote Sensing Society” en 2001.Les deux auteurs adhérèrent à la “Photogrammetric Society” en 1960 et y furent d‘éminents animateurs pendant de nombreuses années. Tous deux occupèrent le poste de président de cette Association mais remplirent égulement plusieurs autres fonctions qui contribuèrent à une gestion efficace. La première intervention d'Atkinson dans le Photogrummetric Record remonte à 1968, et celle de Newton à 1971.〈section xml:id="abs1-3"〉〈title type="main"〉ZusummenfussungEine wissenschaftliche Abhandlung über die Diskussionen zur Gründung, die Gründung selbst und die ersten 20 Jahre der Photogrammetrischen Gesellschaft wurde in 1971 publiziert und in 1974 wiederholt. Dieser aktulle Rückblick konzentriert sich auf die darauffolgenden Jahre der Photogrammetrischen Gesellschaft bis hin zur Vereinigung mit der Gesellschaft für Fernerkundung in Jahre 2001.Die Autoren wurden 1960 Mitglieder in der Photogrammetrischen Gesellschaft und trugen viele Jahre massgeblich zu deren Aktivitäsidenten der Gesellschaft auch verschiedene andere Aufgaben im Management wahrgenommen. Der erste Beitrag von Atkinson im Photogrammetric Record erschien 1968, der erste von Newton in 1971.

Notes: Land systems are patterns of landscape recognised on aerial photographs and mapped to define areas of similar terrain with a similar environment. Breaks of slope often form the major boundaries both between and within land systems. They can be usefully mapped from aerial photographs even if their significance can only be deduced after ground investigation. Many of the characteristics of land systems can be appreciated from aerial photographs and measurements made on the photographs can improve their quantitative description.

Notes: A method of slotted templet triangulation is described in which the authors have used photographs printed on a stable base as the templets. The advantages, disadvantages and possibilities of the method are discussed.

Notes: The determination of the attitude, the position and the intrinsic geometric characteristics of the camera is recognised as the fundamental photogrammetric problem. It can be summarised as the determination of camera interior and exterior orientation parameters, as well as the determination of 3D coordinates of object points. The term “exterior orientation” of an image refers to its position and orientation related to an exterior (object space) coordinate system. Several methods can be applied to determine the parameters of the orientation of one, two or more photos. The orientation can be processed in steps (as relative and absolute orientation) but simultaneous methods (such as bundle adjustments) are now available in many software packages. Several methods have also been developed for the orientation of single images. They are based in general on geometric and topological characteristics of imaged objects.This paper presents a survey of classical and modern methods for the determination of the exterior parameters in photogrammetry, some of which are available as software packages (with practical examples) on the Internet. The methods presented are classified in three principal groups. In the first. a selection of approximate methods for applications that do not require great accuracy is presented. Such methods are also used to calculate values required for iterative processes. In the second group, standard point-bused methods derived from collinearity, coplanarity or coangularity conditions are briefly reviewed, followed by line-based approaches. The third group represents orientation methods based on constraints and on concepts of projective geometry, which are becoming of increasing interest for photogrammetrists. In the last section, the paper gives a summary of existing strategies for automatic exterior orientation in aerial photogrammetry.〈section xml:id="abs1-2"〉〈title type="main"〉RésuméLa détermination de l'attitude, de la position et des caractéristiques intrinsèques de la chambre photographique constitue un problème fondamental en photogrammétrie. Il se résume à la détermination des paramètres de l'orientation de la chambre de prise de vue (paramètres des orientations externe et interne), ainsi qu'à la détermination des coordonnées 30 des points de l'objet. L'orientation externe se rapporte à la détermination de la position et de l'orientation d'une chambre par rapport à un système externe de coordonnées. Différentes méthodes peuvent être utilisées pour calculer les éléments dorientation externe d'une photo, d'un couple ou de plusieurs photos. Le calcul de l'orientation peut être réalisé par étapes (par exemple les orientations relative et absolue) mais les méthodes simultanées (la compensation par faisceaux par exemple) sont actuellement proposées dans la plupart des logiciels. Plusieurs méthodes ont aussi été développées pour l'orientation d'images isolées. Ells sont basées en général sur les caactéristiques géométriques et topologiques des objets photographiés.Dans cet article on présente un ensemble de méthodes classiques et modernes pour la détermination des paramètres de l'orientation externe, certaines d'entre elles étant téléchargeables sous la forme d'applications sur Internet. Les méthodes présentées sont classées en trois groupes principaux. Le premier groupe contient une sélection de méthodes approximatives utilisées d'habitude quand une grande précision n'est pas exigée, ou encore pour calculer des vuleurs approchées des paramètres extrinsèques requises pour les méthodes itératives rigoureuses. Dans le deuxième groupe, on rappelle brièvement les jondements des méthodes basées sur les conditions photogrammétriques fondamentales (la colinéarité, la coplanéité et la coangularité). Dans ce groupe, les méthodes basées sur l'extraction des points ou des lignes sont également abordées. Le troisième groupe traite des méthodes d'orientation basées sur les contraintes et les concepts de la géométrie projective, de plus en plus utilisées par les photogrammètres. Le dernier paragraphe se rapporte aux méthodes destinées à automatiser le calcul de l'orientation externe en photogrammétrie aérienne.〈section xml:id="abs1-3"〉〈title type="main"〉ZusummenfussungDie Bestimmung der Neigung, der Position und den geometrischen parametern der Kamera wird als das fundamentale Problem der Photogrammetrie angesehen. Es kann zusammenfassend sowohl als die Bestimmung der Parameter der inneren und äusseren Orientierung der Kamera angesehen werden, als auch als die Bestimmung von 3D Koordinaten von Objektpunkten. Der Ausdruck “äussere Orientierung” eines Bildes bezieht sich auf die Lage und Orientierung bezogen auf ein äusseres (Objektraum-) Koordinatensystem. Es können verschiedene Methoden angewandt werden, um die Parameter von einem, zwei oder mehreren Bildern zu bestimmen. Die orientierung kann in Schritten erfolgen, was als Relative und Absolute Orientierung bezeichnet wird, aber auch simultane Methoden, wie die Bündelausgleichung, sind in vielen Softwarepaketen implementiert. Es wurden auch Methoden für die Orientierung von Einzelbildern entwickelt, die geometrische und topologische Eigenschaften der abgebildeten Objekte nutzen. In diesem Beitrag wird Beitrag wird eine Studie klassischer und moderner Methoden der Photogrammetrie zur Bestimmung der Parameter der äßeren Orientierung vorgestellt, wovon einige in Softwarepaketen zur Verfügung stehen, die von praktischen Beispielen im Internet ergänzt werden. Die untersuchten Methoden werden in drei Hauptgruppen eingeteilt. In einer ersten Gruppe werden Näherungslösungen vorgestellt, die für Anwendungen mit geringen Genauigkeitsanforderungen geeignet sind. Diese Methoden werden ansonsten für die Näherngswertberechunggen für iterative Prozesse verwendet. IN der zweiten Gruppe werden zuerst die punktbasierten Standardmethoden vorgestellt, die von Bedingungen zur Kollinearität. Koplanarität und Kowinkligkeit abgeletet sind. Danach folgen linienbasierte Ansätze. Die dritte Gruppe umfasst Orientierungsmethoden, die auf Zwangsbedingungen und auf Konzepte der projektiven Geometrie aufbauen, die für Photogrammeter von zunehmendem Interesse sind, Im letzten Abschnitt wird eine Zusammenfassung existierender Strategien für eine automatische äussere orientierung in der Luftbildphotogrammetrie gegeben.

Notes: The paper gives, for a large number of cases, numerical errors due to using approximate, first-order, formulae for correcting x-parallaxes for tilt. The figures show that the errors are considerably smaller than might be expected. It is also shown that the root mean square of the four tilts of a pair of pictures is a reliable measure from which the effect of tilt on heights can be estimated with some confidence.

Notes: Research work is being undertaken by the Department of Orthodontics at Addenbrooke's Hospital, Cambridge, which involves studying the growth of children's faces in three dimensions. In evaluating the morphology of soft tissues, the advantages offered by photogrammetry have been recognised and this paper describes how the technique has been put into practice at the hospital where a stereometric instrument, equally suitable for use as a camera or as a projection plotter, has been constructed.

Notes: The history of the Argentine-Chile frontier is briefly reviewed. The paper then describes the photogrammetric and land-surveying work that formed part of the recent settlement of a section of the frontier, that was referred to the British Government for arbitration.

Notes: Topics of immediate practical interest formed the basis of the Address. Particular emphasis was placed upon problems of point transfer, pre-marking of ground control points, aerial triangulation by observation of independent models, and the status of photogrammetric operators.

Notes: The article describes a method of strip aerial triangulation using the Wild B8 plotter. The principal feature of the method is the transfer of exterior orientation of a camera by measurement of outer orientation parallel to successive airbases.