ALBERT

Notes: This second part deals with a subject analogous to the one developed in the first part, but related to surface irregularities with a non-cylindrical structure. In this part we have taken into consideration both the effects due to potential electrodes and the effects due to current electrodes.The study of these cases has been made with the help of mathematical theory, but it has been necessary to extend this theory from the case of cylindrical bodies to the case of non-cylindrical ones.Finally, as conclusion to both parts of the paper, some pages have been dedicated to the details of the calculation procedure, in order to demonstrate its practical htness for the study of this problem.

Notes: The usual computation methods in refraction seismic in the Sahara often involve considerable shot distances. Therefore, in addition to a high consumption of explosives, difficulties of operation and interpretation arise.In order to cut down the shot distances, it was necessary to study with great care the refracted waves having the shortest possible traveling path along the marker. Such paths correspond to the zone of great relative energy resulting, on one hand, from the sudden increase of reflected energy beyond the critical angle (total reflection) and, on the other hand, from the sudden appearance of refracted energy. The proposed method is founded on correlations of traces located in this “critical zone” on the different records shot on a profile; in order to get around certain difficulties due to insufficient knowledge of the marker velocity, the interpreter is led to select a constant correlation distance, at least for sections of the profile.The paper describes in detail the setting up and utilization of the proposed method, analyses a few examples and gives an estimate of the advantages and the restrictions of this method.

Notes: It was felt that Faust's first law was the best guide in classifying data concerning velocities and their correlation with lithology, even if, on a local basis, other laws fit the observed values better.Data have been re-examined which were provided chiefly by borehole measurements, both conventional and continuous, but also by some particularly reliable velocity profiles. “Faust's coefficient” has been computed for a series of geological formations, i.e. the ratio of true velocity to the value resulting from Faust's law, according to the age and present depth of the formation.Some graphs are shown, in the first place concerning the Sahara, and especially the Palaeozoic. It can be seen that the only formation showing values notably less than I disappears.On the other hand, values greater than I can be noticed for the quartzitic Ordovician of limited thickness.This comparison has been continued on a broader basis, using, in particular, data published by Faust and Wyrobek. The data concerning the very homogeneous Westphalian result in an average value slightly less than I.The Aquitanian basin has been studied in greater detail, owing to the closer spacing of the measurements.Generally speaking, the Middle and Upper Jurassic, the Cretaceous and the Eocene-Oligocene show values notably higher than the Palaeozoic in the Sahara. This seems to be connected with the higher proportion of limestones and dolomites. Values as high as 1.7 are observed in compact dolomites.Four maps are given, concerning the Oligocene, the Eocene-Paleocene (one of them excluding the Danian) and the Upper Cretaceous (exclusive of Danian), and a cross-section showing the link with lithology.Some discrepancies with regard to data from borehole samples are discussed.The question may be raised as to whether such studies can be carried out at the very beginning of exploration of a basin, on the basis of only a few logged wells. In the Aquitaine basin, data given by velocity profiles are in close agreement with those from wells as regards the Tertiary; but as regards the Mesozoic, information is meagre. In basins of the Sahara type, synthetic records have shown that interference of true and multiple reflections with each other is a major drawback. But on the other hand, the possibilities of a combined use of reflection and refraction in order to define lateral changes in velocities may not have been fully appreciated. Some computed examples are shown, since the results of a survey at present being carried out on this basis cannot yet be published.Finally, mention is made of the part played by the determination of anisotropy, and an appeal is made for more coöperation between geophysicists in this sphere.

Notes: The vertical component of the attraction exerted by a horizontal homogeneous polygon is obtained as the sum of terms proportional to the difference, for each of the vertices, between the external angle and its spherical perspective. A set of computation charts is presented, each for a fixed value of the angle of the polygon (22° 30′, 30°, 45°, 67° 30’ and 90°). These charts give the difference between the external angle and its spherical perspective as a function of the quotient of the distance from the sides to the vertical through the station over the depth. The chart for the right angle is an alignment chart, permitting a more accurate reading; the others are graphs in rectangular coördinates.For a remote station the result would be obtained as a small difference between relatively large quantities, and consequently with a not quite satisfactory precision. For these stations it is preferable to assume the entire mass to be concentrated in the centre of gravity.

Notes: In the laboratories of the agip mineraria a new apparatus has been developed which, utilizing reflected energy collected by several groups of seismometers, provides on a single trace an indication of the total energy level. This indication is controled in time according to an exponential characteristic, thus compensating for the attenuation which is effected in the subsurface. The apparatus enables indications of successive energy levels to be obtained for different shots, thus furnishing a time section even during the routine field work.

Notes: The factors affecting the response of a velocity-sensitive well geophone are discussed and it is shown that the geophone movement in response to a seismic pulse is primarily due to the pressure difference between its ends. Several practical examples are calculated to show that the first arrival waveform recorded by a geophone depends on the distance from an interface and that these changes in recorded waveform may give errors of up to 3 msec in well-velocity surveys. These errors may be minimised by using pressure geophones or by avoiding measurements at geological interfaces.

Notes: Surface charges in seismic refraction work in the sand dunes of the Sahara have been necessitated by the many problems involved in shot hole driving. These include lost circulation, unconsolidated surface sands and gravels, caving, poor shot efficiency etc.Tests were conducted in September 1958 in an attempt to evaluate some of the problems involved in surface shooting. This method is complicated by the large number of variables, 8 major ones, influencing the shot pattern.It is difficult to evaluate each of such a large number of variables by an exhaustive and systematic test procedure due to the prohibitive number of shots that this would involve. However, two series of tests contributed greatly to an understanding of the problem, although they left some points to be cleared up.Firstly shots were fired using small charges (less than 25 kg). These gave interesting results, however, they are not applicable to the heavy charges currently in use (500-1500 kg). These results refer primarily to the use of suspended charges which gave superior results to those obtained from surface charges layed on the ground. They also tend to indicate the influence of the weight of the charge. This is manifested by a saturation in seismic energy, as the size of the charge increases.The results obtained from the shooting (200 kg) of several individual charges are not as pronounced. The following conclusions are drawn:Nitrate explosives, in current use in the Sahara for several years, give good results in refraction.– The use of suspended shots does not result in sufficient gain in energy over the ground shots to justify their more complicated utilization: preparation, partial destruction of supports, safety etc. Hence further shooting of suspended charges has been abandoned.– The detonation of individual charges by use of primacord layed parallel to the line, in preference to simultaneous electrical detonation, gave superior results from the energy point of view (especially for high frequency arrivals) and simplified lay-out procedures. Hence this method was adopted.– As for the small charges the relation between seismic energy and weight of the individual charges shows a saturation effect which is less pronounced.–The distance between the individual charges appears to be the most important variable. The relation, seismic energy-distance between charges, indicates an increase in a linear manner for distances of 5 to 20 meters. It would appear as though the beneficial effect for greater distances diminishes beyond this point.Finally, it would appear as though it would be preferable for a given overall charge to reduce the weight of the individual charges and increase the distance between the individual charges. Obviously this rule has certain practical and economic limits. If the cost of the unit of seismic energy is evaluated it is preferable to utilize large distances between charges (20 m) but also relatively large individual charges (about 25 kg).The testing program was followed by nine months of surveying in different types of terrain. The parameters were etablished from the results of the testing program.Economically the following conclusions may be drawn: The average explosives consumption increased from 1000 kg for the shot–hole shots to 1500 kg for the surface shots. This increase, costwise, represents almost exactly the cost of shot hole drilling at the present price of explosives. Efforts are being made to have the price of explosives reduced and should this realize the net result will be a definite cost advantage in favor of surface shooting.In addition, the introduction of magnetic recording in refraction work to the Sahara in 1959 appears to indicate a substantial reduction in the size of the charges needed, hence, a further advantage to surface shooting.

Notes: This is the first of a series of papers giving the solution of the inverse problem in seismic exploration. The acoustic approximation is used together with the assumption that the velocity field has the form 〈displayedItem type="mathematics" xml:id="mu1" numbered="no"〉〈mediaResource alt="image" href="urn:x-wiley:00168025:GPR998:GPR_998_mu1"/〉 . The forward problem is then linearized (thus neglecting multiple reflected waves) and the inverse problem of estimating δ is set up. Its rigorous solution can be obtained using an iterative algorithm, each step consisting of a classical Kirchhoff migration (hyperbola summation) plus a classical forward modeling step (circle summation).

Notes: The response of a seismic model to excitation by a source can be represented in terms of the action of reflection and transmission operators for portions of the structure. This approach provides a flexible framework for both modeling and processing problems.The operator development provides a physical description of the wave propagation process and, via the expansion of reverberation operators, gives a mechanism for assessing the accuracy of approximate developments. The representation suggests new ways of developing modeling algorithms by balancing the computational effort expended on minor and major features of the model.For processing problems, the operator representation shows the relation of processing stages to the seismic wave field and thereby indicates effective sequences of operations. For migration it is possible to specify an ideal pre-stack migration procedure in terms of the inverse of the propagation operators and to examine the problems which need to be overcome by practical algorithms.

Notes: A numerical method is presented for direct interpretation of resistivity sounding measurements. The early part of the resistivity transform curve derived from field observations by standard methods is approximated by a two-layer curve. The resistivity of the first layer is determined from the arithmetic mean of the successive computations which are carried on each of three successive discrete values of the resistivity transform curve. Using this mean value of the resistivity, the thickness of the first layer is computed from the sample values in pairs of the resistivity transform curve. After these determinations, the top layer is removed by Pekeris's reduction equation. The parameters of the second layer are obtained from the discrete values of the reduced transform curve (which corresponds to the second part of the resistivity transform curve) by the same procedure as described for the first layer.The same computational scheme is repeated until the parameters of all intermediate layers are obtained. The resistivity of the substratum is determined from the reduction equation.

Notes: In odd-depth structure the two-way traveltime to each boundary is constrained to be an odd integer. The odd-depth property of a model is exposed to possible refutation under a seismogram test. Test function is a simple transformation of a synthetic seismogram. For an odd-depth model the test function has identically the value 1.The testability of a synthetic seismogram over an odd-depth structure provides a method of deterministic deconvolution. There is no need of specialized assumptions, like the minimum-phase property, about the source wavelet. The deconvolution may be performed in the absence of the early segment of a seismogram.

Notes: Zero-offset-source VSP surveys provide information about the subsurface only within the Fresnel zone centered at the well. Offsetting the source location moves the reflection zones away from the well thus providing lateral cover.Conventional processing of this type of data gives rise to a distorted image of the subsurface. Using a simple ray-tracing scheme, this image may be reconstructed into the more familiar coordinate system of the surface seismic section. This simple data-independent mapping is based on the assumption of horizontal layering and requires a vertical velocity profile.The technique of placing the source away from the borehole was first applied to the single-offset-source VSP survey. However, data from any survey geometry (such as deviated well with rig source, walkaway VSP, etc.) can be mapped to the coordinate system defined by the appropriate seismic section.To obtain the best results from this type of survey the target area must be defined and simple modeling techniques used to optimize the source location(s). These pre-survey modeling methods may also be used to anticipate—and hence avoid a number of problem areas which experience has highlighted.The data from any VSP survey is the result of a realizable experiment and as such obeys the wave equation. This implies that the wave equation may be used to migrate the data to its true subsurface location. Theoretically, such a process is more secure than ray-tracing techniques, although its practice presents many difficulties.

Notes: A mathematical expression for potential of a direct current point source in an inhomoge-neous anisotropic earth is derived. The coefficient of anisotropy is given by f= (σr/σz), where σr and σz are the conductivities parallel and perpendicular to the bedding plane. It is assumed that σz varies with depth, whereas σr varies transversely. This potential may be useful in interpretation of geoelectrical data in specified geological situations. Master curves for Wenner and Schlumberger configurations are presented

Notes: Total magnetic intensity contour maps for the study region (between 2°E to 10°E and 56°N to 60°N) were digitized and converted to a regular grid of 285 × 285 points. The study area measures approximately 444 km × 444 km and the grid spacing is thus 1. 56 km. The International Geomagnetic Reference Field for 1975 was gridded for the above-used net, and from the two data sets a further grid of the ▵T field was generated. A large number of profiles were constructed which were suitable for depth determinations. The regular grid ▵T data is also convenient for the computation of the second vertical derivative. Using the method of vertical prisms of Vacquier et al. (1963), a large suite of curvature-depth indices was measured to complement the depths obtained from the intensity slopes and from boreholes which reach the crystalline basement. The depth to the magnetic basement has been contoured, and the resulting map is shown to be in good agreement with what is known about the deeper geology of the study area.The work reported here is part of a research project supported by Amoco Norway, BP Petroleum Development Ltd, Elf Aquitaine, Esso Exploration and Production, Norwegian Gulf, Norsk Hydro, Mobil Exploration Norway, Norwegian Petroleum Directorate, Royal Norwegian Council for Scientific and Industrial Research (NTNF), Norske Shell, and Statoil.

Notes: Geophysical inversion involves the estimation of the parameters of a postulated earth model from a set of observations. Since the associated model responses can be nonlinear functions of the model parameters, nonlinear least-squares techniques prove to be useful for performing the inversion. A common type of inversion applies iterative damped linear least squares through use of the Marquardt-Levenberg method. Traditionally, this method has been implemented by solving the associated normal equations in conventional ways. However, Singular Value Decomposition (SVD) produces significant improvements in computational precision when applied to the same system of normal equations. Iterative least-squares modeling finds application in a wide variety of geophysical problems. Two examples illustrate the approach: (1) seismic wavelet deconvolution, and (2) the location of a buried wedge from surface gravity data. More generally, nonlinear least-squares inversion can be used to estimate earth models for any set of geophysical observations for which an appropriate mathematical description is available.

Notes: In this study we derive expressions for particle displacement or particle velocity anywhere inside a stratified earth and at its surface due to horizontal torque source located in the top layer. Equivalently, invoking Green's function reciprocity theorem, the solution applies also to the case of a surface or subsurface source when the resulting displacement or velocity is measured within the top layer.In order to evaluate the closed-form analytical solution economically and accurately it is advisable to introduce inelastic attenuation. Causal inelastic attenuation also lends the necessary realism to the computed seismic trace. To provide proof that the analytical solution is indeed correct and applicable to the multilayer case, a thick uniform overburden was assumed to consist of many thin layers. The correctness of the computed particle velocity response can be very simply verified by inspection. The computed response can also serve as a check on other less accurate methods of producing synthetic seismograms, such as the techniques of finite differences, finite elements, and various sophisticated ray-tracing techniques.It is not difficult to construct horizontal surface torque source. It appears that such source is well suited for seismic exploration in areas with a high-velocity surface layer. A realistic source function is analyzed in detail and normalized displacement response evaluated at different incidence angles in the near and the far fields.In an effort to distinguish the features of an SH torque seismogram from a pressure seismogram two models with identical layerings and layer parameters have been set up. As expected the torque seismogram is very different from the compressional seismogram. One desirable feature of a torque seismogram is the fast decay of multiples.Exact synthetic seismograms have many uses; some of them, such as the study of complex interference phenomena, phase change at wide angle reflection, channeling effects, dispersion (geometrical and material), absolute gain, and inelastic attenuation, can be carried out accurately and effortlessly. They can also be used to improve basic processing techniques such as deconvolution and velocity analysis.The numerical evaluation of the analytical solution of the wave equation as described in this paper has a long history. Most of the work leading to this paper was carried out by one of us (M. J. K.) in the years 1957 to 1968 at the Geophysical Research Corporation. However, the full testing of the various computer codes was carried out only very recently at the Phillips Petroleum Company.

Notes: In South and Central Goa iron ore occurs in two parallel belts with the general NW-SE Dharawar trend. The ore occurrence, however, is not continuous. There are barren zones as well as zones of very high concentration in some of which there are mining activities.Landsat MSS data have been interpreted over a zone covering both mineral belts in order to delineate the ore occurrences. As a guide line a known ore-bearing area has been considered along with the unknown zones.On the basis of two-dimensional plotting of gray level values it has been found that the MSS bands 4 and 7 are most suitable for the studies over iron-rich areas in Goa. Two techniques are described here for the processing of the MSS data; the separation of residual from the regional and MSS band-ratioing. It is observed that (i) the gray level residual maps of MSS bands 4 and 7 are of use in demarcating the iron-ore-bearing zones, and (ii) an existing mine, an abandoned mine, and a proved iron ore zone could be delineated by MSS band-ratioing. On the basis of the latter technique, a few areas with ore occurrence potential have been indicated.

Notes: The most common source of seismic energy is an explosion at some depth in a borehole. The radiated waves are reflected not only at the subsurface layers but also at the free surface. The earth's surface acts as a generator of both P- and S-waves.If the source depth is much less than the dominant wavelength the reflected waves resemble closely the waves generated by a single force. Theoretical seismograms were computed with different methods to look for the relevance of the surface-reflected waves. The numerical experiments show reflected shear waves even for small shotpoint—receiver distances. Due to their polarization these waves can be detected most easily on in-line horizontal geophones. The existence of these waves was examined during a conventional survey in Northern Germany. Conventional data analysis shows a large variability in the νp/νs ratio. The method used here produced a shear-wave section with a rather good signal-to-noise ratio down to 4 s S-wave reflection time.

Notes: We describe the concept of physico-geological models (PGMs) in geophysical exploration. They represent a “general model”, a spatial combination of a set of particular models (disturbing bodies). The modeling is called complete, incomplete or approximate, depending on the degree of characterization of the PGM by parameters such as dimension, shape and petrophysical property. Each of the three modeling types can be realized as a conceptual, and analytical, or a material PGM. Both deterministic and stochastic PGMs exist; deterministic models are mainly used to investigate the possibilities of a geophysical method, while stochastic models serve to substantiate complex geophysical interpretations.Depending on the geological problem, PGMs are subdivided into multi-alternative models (geological mapping, prediction, general prospecting) and double alternative models (specialized prospecting).An exploration-oriented classification of the PGMs of mineral deposits is discussed. According to this classification the variety of known genetic deposit types is reduced to a limited number of generalized PGM types. The development of typical PGMs is illustrated with examples of magnetitic deposits of Siberia.

Notes: An inverse problem is one in which the parameters of a model are determined from measured seismic data. Important to the solution of inverse problems is the issue of whether or not a solution exists. In this paper we show, in a constructive manner, that a solution does exist to the specific inverse problem of determining the parameters of a horizontally stratified, lossless, isotropic and homogeneous layered system that is excited by a non-normal incidence (NNI) plane wave. Mode conversion between P- and S-waves is included.We develop a seven-step layer-recursive procedure for determining all of the parameters for layer j. These parameters are P-wave and S-wave velocities and angles of incidence, density, thickness, traveltimes, and reflection- and transmission-coefficient matrices. Downward continuation of data from the top of one layer to the top of the next lower layer is an important step in our procedure, just as it is in normal incidence (NI) inversion. We show that, in order to compute all parameters of layer j, we need to (and can) compute some parameters for layer j+ 1. This is a non-causal phenomenon that seems to be necessary in NNI inversion but is not present in NI inversion.

Notes: The suitability of VLF ground surveys in the investigation of shallow two-dimensional structures is analyzed. For such structures the polar formalism is derived, necessary in practice since the transmitters are generally not in the structural strike or profile. A simple vertical dike is considered to demonstrate the striking anisotropy which can be expected over such a structure, in particular the high apparent resistivity along the direction of a well-conducting dike and the low resistivity across it. The theory is then confronted with the practical example of an asymmetrical vertical dike resulting from a strike-slip fault. Modelling of the survey results is very successful and yields good confirmation of the polar behaviour. VLF ground surveys thus provide a quick and powerful tool for the study of geological accidents within about 100 m of the surface.

Notes: A new mode of operation for the Turam electromagnetic exploration system is proposed in which the transmitter loop is placed across the expected trend of a conductor and the receiver is operated along lines parallel to one side of the transmitter. The concept appears to offer several benefits which include greatly extended traverse length, the use of large coil spacing, rejection of the effects of conductive environments, and consistency in the indication of target dip.

Notes: Determination of thickness of sediments (usually of high conductivity) overlying a high-resistivity basement is one of the basic problems of electrical exploration methods. This paper proposes to determine horizontal electrical conductance on the basis of impedance calculated from electrical and magnetic fields of distant quasi-static (low-frequency) point sources. Using the proposed method, horizontal conductance of the sediments can be determined also from artificial quasi-static noise-impulses coming from sources of unknown position and intensity. The results of analogue modeling and field examples prove the potential of the proposed technique.

Notes: Since the early years of seismic surveying, field engineers and observers have been faced with the appearance of interference at power-line frequency (and harmonics) on seismic records: 60 Hz in the Americas, 50 Hz in Eurasia; and 16 2/3 Hz (the train supply frequency in Germany, Austria, and Switzerland) in part of Europe. Such interference is picked up from the ground surface through electric leakage between geophone leads and ground.To minimize power-line interference, the autobalancer automatically performs a balancing procedure by adjusting two potentiometers on each channel—essentially the same operation as manually performed by seismic operators for decades. The first 24-channel system became operational in 1977.The first-generation design comprised two 256-position electronic switching potentiometers. Over 4 years of experience with this system in all parts of the world has shown its value under a variety of field conditions. Improvements up to 30 dB were often found, sometimes even up to 40 dB. Balancing time was about 30 s.A second-generation design was field-tested in 1981. Potentiometer stepping is now performed at three levels: coarse, medium, and fine. This leads to faster operation and better resolution: balancing time is about 10 s; improvements up to 60 dB are occasionally found.A later modification gives a further reduction of the balancing time to 5 s in 60 Hz areas or 6 s in 50 Hz areas.

Notes: The technique of digital linear filtering is used for transformation of apparent resistivity data from one electrode configuration into another. Usually filter spectra are determined via the discrete Fourier transforms of input and output functions: the filter characteristic is the quotient of the spectra of the output function and input function.In this paper, the transformation of the apparent resistivities is presented for four electrode configurations (Wenner, the two-electrode, Schlumberger, and dipole configurations). In our method, there is no need to use the discrete Fourier transform of the input and output functions in order to determine the filter spectrum for converting apparent resistivity in one electrode configuration to any other configuration. Sine responses for determination of the derivative of apparent resistivities are given in analytical form.If the filter spectrum for converting the apparent resistivity to the resistivity transform for one electrode configuration is known, the filter spectra for transforming the apparent resistivity to the resistivity transform for any electrode configurations can be calculated by using newly derived expressions.

Notes: In the western coal-mining area of Ruhrkohle AG, reflection seismic prospecting for the Carboniferous coal measures is severely impaired by structures with halokinetic features. These structures make the interface between Mesozoic and Paleozoic layers, i.e., the top of Zechstein in general, very rugged. Unfortunately the velocity contrast at this interface is very high in that area, the ratio of velocities being 1.5 to 2.0. Therefore, migration and stacking become a problem.Three types of migration are presented:〈list xml:id="l1" style="custom"〉1(f, x)-time-migration with vertical time-to-depth conversion as a second step.2Kirchhoff migration down to a level determined approximately by the highest points of the top of Paleozoics, i.e., 0.35 s, and Kirchhoff-downward continuation for all times exceeding 0.35 s. Intermediate static corrections for these latter times with subsequent (f, k)-time-migration and final vertical time-to-depth conversion.3Direct depth migration in the (f, x)-domain using three interval velocities.In all cases an intermediate picking of the velocity interfaces is necessary. In case 2 this occurs at an earlier stage of the process than in case 1, and in case 3 at a still earlier stage.The results of the second and third migration procedures are superior to those of the first. Possibilities for misinterpretation of faults are reduced considerably when the second or third migration procedure is applied.

Notes: Airborne electromagnetic methods are most commonly used in mineral exploration. However, new developments, such as multifrequency capability and digital on-board field recording, as well as improvements in instrumentation resulting in high signal-to-noise ratios in recorded data, have made their application in geological mapping possible.A three-frequency airborne EM survey carried out over an area northwest of Timmins, Ontario, was interpreted in terms of thickness and resistivity of the layers of a two-layer earth section. Since both in-phase and quadrature components are measured, this provides six independent parameters at each point in space. Based on prior geological information and a preliminary interpretation of the field records, two two-layer models of the subsurface seemed to be appropriate for most of the survey area. An automatic computerized interpretation procedure was devised to interpret the field data at each point in terms of thickness and resistivity parameters of those two models. When the geology is more complex, the data do not fit the models and no interpretations are made. Two maps illustrating the variation of the resistivity and the thicknesses of the layers were constructed from the interpreted data. These maps agree with the known geological information about the distribution of glacial clay in the area. Areas where the layered models do not fit are known to be areas where the geology is complex with a large number of dykes and other lateral inhomogeneities. The study shows that multifrequency airborne EM surveys can be very useful in geological mapping over inaccessible terrain and can significantly help the mapping geologist where outcrops are scarce.

Notes: Shear (= S) wave studies in addition to compressional (= P) wave surveys have revealed that S-wave velocities are much more variable than P-wave velocities. This strongly affects Poisson's ratio σ, especially in young sediments. It is shown that σ has a great influence on the directivity pattern, i.e., on the radiation and receiving characteristic of horizontal sources and receivers. For their calculation, well-known surface boundary conditions and White's statement of the reciprocity relation (White 1965) are used. They also form the basis for the combination of source and receiver patterns essential for practical field work. The various combinations of horizontally and vertically arranged sources and receivers are investigated with regard to their directivity pattern, their amplitude ratio and, in general, to their usefulness in seismic prospecting.

Notes: Previously ignored characteristics of the seismic recording instrument are presently experienced as limitations as more sophisticated interpretive methods using wider frequency ranges are developed to extract stratigraphic information from seismic land data for hydrocarbon and mineral exploration. Most of these limitations arise from inadequate characteristics of the first element of the seismic instrument: the geophone. A geophone does not faithfully follow the motion of the earth for higher frequencies due to poor geophone-earth coupling. This filtering effect brings about time shifts that are dependent on the frequency and the soil type. A geophone can also produce spurious outputs, brought about by the motion of the suspended part of the geophone, with a magnitude comparable to that of the desired output. The suspension is made very compliant to obtain the required sensitivity. A compliant suspension, however, gives a large sag. The geophone can therefore only be used in one position, tolerating little tilt. A compliant suspension also widens the traveling range of the movable part. Minor sensitivity changes with travel are then noticeable as nonlinearity, since the surface wave is large with respect to the reflected wave. A compliant suspension is usually realized in the form of thin, spirally shaped spring-spiders. Such suspensions exhibit transverse or rotational resonances that are in or close to the seismic frequency band. Excited by ground roll, they can produce considerable undesirable output.The novel geophone we describe is a light-weight (17 g) acceleration-sensitive transducer which gives good ground coupling and partial correction for the increasing damping in the earth with increasing frequencies. It employs internal hybrid electronics for a magnetodynamic velocity-nulling feedback system. Velocity nulling makes the movable part of the geophone virtually rigid with respect to the housing. This makes the geophone characteristics independent of the suspension. The springs used are stiff in a transverse and rotational direction so that the suspension resonances are well outside the useful frequency band. This suspension also allows the geophone to be used in any orientation while being only sensitive to the vibration component along the main axis. The feedback system makes the sensitivity flat within 1 dB from 2 Hz to 500 Hz, with a phase tolerance smaller than 5°. The geophone is robust, has no moving internal wires, employs a current output [sensitivity 1 mA/(m s−2)] and internal gain so that the signal-to-cable-noise ratio is improved. This type of output allows parallel connection without any interaction between the geophones.

Notes: There are two types of masked layers in seismic refraction work: the velocity reversal (low-velocity layer) and the hidden layer (insufficient velocity contrast or layer thickness). On the basis of an analytical formulation of the general case of a masked layer under an overburden of plane and parallel multiple refractors the two limiting cases are discussed: the solution resulting from an uncritical interpretation of the measured time-distance curve and the blind zone solution. Between these two limiting cases there is a variety of possible masked layer solutions. These no-blind zone solutions—as well as the blind zone solution itself—are formulated separately for the velocity inversion and the hidden layer case.For the evaluation of some no-blind zone solution a diagram is presented which can be used for any case of multiple refractors in the overburden of the masked layer. However, it is only for the three- and the four-layer case that a blind zone interpretation by use of diagrams is advisable. Such diagrams are presented together with the basic sets of formulae which contain as parameters only ratios of velocities and layer thicknesses. As the velocity of the masked layer is usually unknown the diagrams are principally constructed to show the dependence on the masked layer velocity. This is useful for estimation of the largest possible error.

Notes: Wave equation migration techniques have shown the limits of traditional stacking methods with data from tectonically complicated areas. An improved stack can be obtained utilizing the dip-moveout correction technique based on offset continuation. The properties and the limits of the algorithms used are summarized briefly.Several synthetic and real data examples are shown and compared with the results obtained using conventional processing in order to show the focusing effects and the strong improvement in signal-to-noise ratios, both at the stacked and migrated section level. The possibility of exploiting this technique to transform multiple coverage into increased spatial resolution is illustrated with examples.

Notes: The far-field signatures from a comprehensive and systematic airgun pulse test have been analyzed. Empirical relations between the characteristic signature parameters and depth (5–12 m), pressure (100–137 bar = 10–13.7 MPa) and total chamber volume (0.65–9.5 l) have been derived. Also, the influence of using waveshape kits in different positions within the chamber has been tested.The results indicate that:〈list xml:id="l1" style="custom"〉1 The amplitude is proportional to chamber pressure to the power 3/4.2 The bubble period is nearly independent of the position of the waveshape plate.3 The increase in primary/bubble amplitude ratio is inversely proportional to the chamber volume above the waveshape plate.4 The amplitude is independent of airgun depth.Suggestions and comments regarding this work from Dr B. Ursin and Dr A. Ziolkowski are appreciated. The field work was supported by the Norwegian Petroleum Directorate through the Continental Shelf Project at the Seismological Observatory, University of Bergen.An airgun allowing for continuous variation of the chamber volumes was supplied by GECO (Geophysical Company of Norway). The purchase of two airguns was financed by Norske Getty Exploration A/S.

Notes: The accuracy of short length digital linear filter operators can be substantially increased if the sampling interval as well as the abscissa shift are properly adjusted. This may be done by a trial and error process of adjustment of these parameters until the error made by the filter operator, applied to a suitably chosen test function, is smallest.As an illustration of the application of this method, 7-, 11- and 19-point filters for the calculation of Schlumberger apparent resistivity from a known resistivity transform are designed. Errors with the new 7-point filter are seen to be less than those with a 19-point filter of conventional design. The errors with the new 19-point filter are two to three orders of magnitude smaller than those made by the conventional 19-point filter.The new method should provide digital linear operators that allow significant improvements in accuracy for comparable computation efforts, or substantial reduction in computation for comparable accuracy of results, or something of both.

Notes: A well-known technique for the migration of normal-incidence two-way travel-time maps is extended to common-source-point travel-time data. The travel time and the travel-time gradient are used to compute the parameters defining the tangent plane of the reflecting interface. It is also shown how the curvature matrix of the received wavefront can be used to compute the curvature of the reflecting interface. The method is initially derived for common-source-point data and then extended to common-midpoint data.In a three-dimensional medium the wavefront curvature matrix is computed by solving a 2 × 2 symmetric matrix Riccati equation. In a two-dimensional medium and in a medium with constant velocity gradient, the wavefront curvature matrix is computed by solving a scalar Riccati equation and two linear equations. The migration procedures are also simplified.When the velocity function is unknown, the migration procedures cannot be used. An inverse modeling algorithm which simultaneously performs the migration and estimates the velocity function must then be applied. Two different inversion schemes are discussed briefly.

Notes: Time-domain-induced polarization (IP) laboratory measurements were performed on about 200 fine sediment samples with varying water content. The results permitted an analysis of IP properties of clays, loams, silts, and sands.Particular emphasis has been given to the analysis of the chargeability m as a function of lithotype and the water content.By analyzing decay curves, a new parameter was identified. It is a statistically specific characteristic of the lithotype and is independent of the water content. Therefore, it provides a diagnostic parameter for lithotype identification. In association with the values of chargeability and electrical resistivity, this parameter permits a reliable evaluation of water content and yields useful information about the porosity and permeability of the lithotype.

Notes: Approaches to the reduction of bias in the computation of the elements of the magnetotelluric impedance tensor have been proposed in the past by several authors. In this paper a clear distinction is made between random errors and bias errors. No effort is made to reduce either, but the emphasis is on their estimation. Both types of errors depend critically upon the polarization of the magnetic field. The random error increases with increasing noise-to-signal ratio in the electrical field, and it is rather insensitive to noise in the magnetic field. The bias error increases with increasing noise-to-signal ratio in the magnetic field. Expressions for random errors and maximum bias errors are developed and discussed using a single station set-up. Random errors with a reference station set-up are also calculated.

Notes: Dipole-dipole induced polarization (IP) data are displayed typically as multi-level profiles, or as contours on vertical sectional plots referred to as pseudo-sections. The dipole-dipole array tends to yield IP anomalies in which the most anomalous values are displaced laterally from the source body. The data patterns are fairly interpretable on pseudo-sections or on multi-level profiles but are sufficiently complex to discourage the contouring of the data in plan.A method was developed for the presentation of dipole-dipole IP data on a contour map. The method consists of a simple averaging of data which can be performed manually if desired. It yields a single output value per station which reflects all levels of the pseudo-section, and is suitable for contouring in plan. The advantage of the technique is that it provides a quantitative picture of IP anomalies in their background or regional setting.

Notes: Constant offset sections can be mapped to a fixed offset and compared in order to provide a method of velocity analysis. The direct mapping to zero offset prior to stack might provide an alternative processing procedure to NMO and stack. The main advantage of such a procedure would lie in the correct treatment of cross-dips, but interpretational advantages might also follow from the performance of partial stacks biased to either high or low offset information.

Notes: Induced polarization and resistivity model studies over thin dykes for varying resistivity contrasts, depth of burial, and dip angles show striking parallelism of the surface apparent resistivity contours with the boundary of the body. This effect may be utilized for the estimation of strike length of the body. Results show that intermediate values of the electrode spacing is satisfactory for detection under widely varying conditions of resistivity contrast and depth. The percentage frequency effect (P.F.E.) and the metal factor (M.F.) responses are found to be more sensitive to the variation in the depth of burial than the resistivity responses. Pseudosections for P.F.E. and M.F. are concentrated much closer to the body than the resistivity pseudo-sections.

Notes: A direct interpretation scheme is developed which is capable of determining most of the geological features of a ground which can be assumed to be two dimensional in structure. This scheme extends the earlier work of Pekeris (1940) and Koefoed (1968) to the case where the basal layer of a ground is undulating. It also has a limited use for finding the parameters of a dipping dyke in the lower medium. Though the top and dip of the dyke can be determined, this is not true for the thickness.

Notes: Laboratory studies of absorption-frequency behavior in rocks often use spectral ratios of digitally recorded ultrasonic signals which have been transmitted through a rock sample and a reference sample of very low absorption, respectively. It is proposed to treat the digitally recorded signals as an autoregressive-moving average (ARMA) process which, using recursive filter concepts, can be represented as a ratio of two polynomials in the z-transform variable z. The numerator polynomial contains only that part of the signal that is modified by anelastic effects, whereas the denominator contains the elastic effects of the physical apparatus such as reverberations. Examples are given which show that this separation of the recorded signal greatly facilitates the laboratory investigation of loss mechanisms and absorption-frequency behavior based on spectral ratios.

Notes: The generalized integral equation for the electric potential governed by a quasi-harmonic equation can be derived via a variational formulation. For surface current distributions it is not always a Fredholm integral equation of the second kind. Numerical solutions of the general heterogeneous problem can be obtained with the “reciprocal averaging technique”, where the solution is obtained a second time after exchange of source and field points.

Notes: A method to calculate the resistivity transform of Schlumberger VES curves has been developed. It consists in approximating the field apparent resistivity data by utilizing a linear combination of simple functions, which must satisfy the following requirements: (i) they must be suitable for fitting the resistivity data; (ii) once the fitting function has been obtained they allow the kernel to be determined in an analytic way.The fitting operation is carried out by the least mean squares method, which also accomplishes a useful smoothing of the field curve (and therefore a partial noise filtering). It gives the possibility of assigning different weights to the apparent resistivity values to be approximated according to their different reliability.For several examples (theoretical resistivity curves in order to estimate the precision of the method and with field data to verify the practicality) yield good results with short execution time independent of shape the apparent resistivity curve.

Notes: We present a new method for the extraction and removal of the source wavelet from the reflection seismogram. In contrast to all other methods currently in use, this one does not demand that there be any mathematically convenient relationship between the phase spectrum of the source wavelet and the phase spectrum of the earth impulse response. Instead, it requires a fundamental change in the field technique such that two different seismograms are now generated from each source-receiver pair: the source and receiver locations stay the same, but the source used to generate one seismogram is a scaled version of the source used to generate the other. A scaling law provides the relationship between the two source signatures and permits the earth impulse response to be extracted from the seismograms without any of the usual assumptions about phase.We derive the scaling law for point sources in an homogeneous isotropic medium. Next, we describe a method for the solution of the set of three simultaneous equations and test it rigorously using a variety of synthetic data and two types of synthetic source waveform: damped sine waves and non-minimum-phase air gun waveforms. Finally we demonstrate that this method is stable in the presence of noise.

Notes: In this paper a theorem is demonstrated which allows—after the introduction of a suitable dipole kernel function or dipole resistivity transform function—to write the apparent resistivity function as an Hankel transformable integral expression.As a practical application of the theorem a procedure of quantitative interpretation of dipole soundings is suggested in which the dipole resistivity transform function obtained after inversion of the original dipole apparent resistivity data is used to control the goodness of the set of layering parameters which have been derived with our previous method of transformation of dipole sounding curves into equivalent Schlumberger diagrams.

Notes: The Hankel transform theorem can be applied to the inversion of gravity data for the buried sphere, the horizontal cylinder, and the vertical rod. This new approach leads to exact solutions of the transforms for the assumed bodies. A comparison with the classical procedure by Fourier transform reveals that for the sphere and the vertical rod, the Hankel transform is preferable.

Notes: Air guns have been used in various applications for a number of years. They were first used in coal-mining operations and were operated at up to 16000 psi charge pressures. Later, single air guns, operated at 2000 psi, found application as an oceanographic survey tool. Air gun arrays were first used in offshore seismic exploration in the mid-1960's. These early arrays were several hundred cubic inches in total volume and were operated at 2000 psi; they were either tuned arrays or several large guns of the same size with wave-shape kits. Today's arrays have total volumes greater than 5000 cu in. and are typically operated at 2000 psi. Recently, higher-pressure, lower-volume arrays operated at 4000–5000 psi have been introduced; guns used in these arrays are descendants of the coal-mining gun.On first thought one would equate increased gun pressure linearly with the amplitude of the initial pulse. This is approximately true for the signature radiated by a “free-bubble” (no confining vessel) and recorded broadband. The exact relation depends on the depth at which the gun is operated; from solution of the free-bubble oscillation equation, the relation is 〈displayedItem type="mathematics" xml:id="mu1" numbered="no"〉〈mediaResource alt="image" href="urn:x-wiley:00168025:GPR700:GPR_700_mu1"/〉 If Pc,1= 6014.7 psia, Pc,2= 2014.7 psia and PO, 1=PO, 2= 25.8 psia (corresponding to absolute pressure at 25 ft water depth), then 〈displayedItem type="mathematics" xml:id="mu2" numbered="no"〉〈mediaResource alt="image" href="urn:x-wiley:00168025:GPR700:GPR_700_mu2"/〉 Experiments were conducted offshore California in deep water to determine the performance of several models of air guns at pressures ranging from 2000 to 6000 psi and gun volumes ranging from 5 to 300 cu in. At a given gun pressure, the initial acoustic pulse Pa correlated with gun volume Vc according to the classical relation 〈displayedItem type="mathematics" xml:id="mu3" numbered="no"〉〈mediaResource alt="image" href="urn:x-wiley:00168025:GPR700:GPR_700_mu3"/〉 For 1 ms sampled data the ratio 〈displayedItem type="mathematics" xml:id="mu4" numbered="no"〉〈mediaResource alt="image" href="urn:x-wiley:00168025:GPR700:GPR_700_mu4"/〉 varied between 4.5 and 5.5 dB depending on gun model. Pulse width of the 2000 psi signatures indicated they are compatible with 2 ms sample-rate recording while pulse width of the 6000 psi signatures was greater, indicating they are less compatible with 2 ms sample-rate recording.Conclusions reached were that 2000 psi air guns are more efficient than higher pressure guns and are more compatible with 2 ms sample-rate requirements.

Notes: Numerous electrodes, already used in geophysics or just perfected by us, have been compared by measuring the three main characteristics which interest the user: noise spectrum, temperature coefficient and polarization with its stability versus time.Among the most used unpolarizable electrodes, silver-silver chloride (Ag-AgCl) are the best ones. But a systematic research of all different possible metal-salt couples, have led us to use lead-lead chloride (Pb-PbCl2) for the following reasons: noise as low as the one of Ag-AgCl at 1 Hz and even lower for the low frequencies (0.4 μV at 1 Hz and 1.2 μV at 0.01 Hz for peak to peak value and ΔF=F), temperature coefficient about ten times weaker (−40 μV/°C instead of −450 μV/°C) and also better long time stability of the polarization (1 mV/month instead of 2 at 10 mV/month).We have been using these electrodes since 1977 as “tube” electrodes which are very easy to use. They allow us to record correctly the fast variations thanks to their low noise, the very slow variations, their low temperature coefficient and their stability, and this with telluric lines only about 100 m long.

Notes: The compression of seismic signals which have propagated through a dispersive medium can be achieved by a frequency-domain transformation. This transformation is formally related to the dispersion characteristic of the medium and is independent of phase and group velocities. By defining a suitable cost-function to measure the degree of dispersion of a time- signal, an iterative technique can be employed to find that transformation which gives minimum dispersion.In this paper, we assume that the inverse of the dispersion characteristic can be adequately approximated by a finite polynomial in the region of maximum signal energy density. The coefficients of this polynomial are the parameters of dispersion of the medium. These parameters can be estimated both in the presence of noise and in the case of signals made up of multiple arrivals.The techniques developed in this paper are applied to seismic signals which have been recorded underground by a set of geophones designed to detect and map discontinuities in coal-seams. Results of dispersion estimation and signal compression are discussed for data collected in the Blackshale seam, Pye Hill Colliery, near Derby, in the United Kingdom.

Notes: Sign reversals have been observed with the one-loop version of the TEM method in an area near Cloncurry, Queensland. This is the only area in which such a response has been recorded in seven years of field surveys by the Australian Bureau of Mineral Resources.The geology of the area consists mainly of pyrrhotitic graphitic shale, which has resistivities as low as 0.1 Ωm and frequency effects up to 30%. The sign reversals could be due to magnetic phenomena, reflections from layers, or complex conductivity effects.

Notes: A crucial step in the use of synthetic seismograms is the estimation of the filtering needed to convert the synthetic reflection spike sequence into a clearly recognizable approximation of a given seismic trace. In the past the filtering has been effected by a single wavelet, usually found by trial and error, and evaluated by eye. Matching can be made more precise than this by using spectral estimation procedures to determine the contribution of primaries and other reflection components to the seismic trace. The wavelet or wavelets that give the least squares best fit to the trace can be found, the errors of fit estimated, and statistics developed for testing whether a valid match can be made.If the composition of the seismogram is assumed to be known (e.g. that it consists solely of primaries and internal multiples) the frequency response of the best fit wavelet is simply the ratio of the cross spectrum between the synthetic spike sequence and the seismic trace to the power spectrum of the synthetic spike sequence, and the statistics of the match are related to the ordinary coherence function. Usually the composition cannot be assumed to be known (e.g. multiples of unknown relative amplitude may be present), and the synthetic sequence has to be split into components that contribute in different ways to the seismic trace. The matching problem is then to determine what filters should be applied to these components, regarded as inputs to a multichannel filter, in order to best fit the seismic trace, regarded as a noisy output. Partial coherence analysis is intended for just this problem. It provides fundamental statistics for the match, and it cannot be properly applied without interpreting these statistics.A useful and concise statistic is the ratio of the power in the total filtered synthetic trace to the power in the errors of fit. This measures the overall goodness-of-fit of the least squares match. It corresponds to a coherent (signal) to incoherent (noise) power ratio. Two limits can be set on it: an upper one equal to the signal-to-noise ratio estimated from the seismic data themselves, and a lower one defined from the distribution of the goodness-of-fit ratios yielded by matching with random noise of the same bandwidth and duration as the seismic trace segment. A match can be considered completely successful if its goodness-of-fit reaches the upper limit; it is rejected if the goodness-of-fit falls below the lower one.

Notes: If the conductivity of any one of the layers of a horizontally stratified earth varies exponentially with depth with or without a discontinuity at the interface, the corresponding expressions for apparent resistivity for Wenner- and Schlumberger-sounding arrays can be formulated. The general case has been broadly divided into three categories for mathematical simplicity. All previous discussions of this problem can be regarded as particular cases of the present study.

Notes: The physical properties of the serpentinized pyroxenitic and saxonitic rocks from stratiform ultramafic complexes of Roro, Singhbhum distrct, India, are examined using principal factor (R-mode) analysis technique. The variations and inter-relations of these properties reflect the compound effects of two processes—(a) degree of serpentinization, and (b) mineralogical and other changes attendant to serpentinization. Factor analysis is thus shown to be an effective tool for petrophysical inferences.

Notes: The problem of numerical evaluation of apparent resistivity curves is treated by finite difference modeling. The models proposed are set up in cylindrical coordinates and yield the potential field due to a point source located in a radially symmetric environment. The Schlumberger configuration, widely used for surface measurements, is emphasized. However, the treatment is equally applicable to other similar situations such as the computation of synthetic electric logs when the resistivity of the borehole fluid is different from that of the surrounding uniform or stratified medium. Moreover, the individual layers may not necessarily be isotropic.The medium under investigation is discretized by using a very coarse system of horizontal and vertical grid lines whose distance from the source increases logarithmically; consequently, the physical dimensions of the medium can be made “infinite” without affecting the numerical size of the model. Finer features such as a thin but anomalously resistive or conductive bed which would ordinarily be missed in coarse discretization are accurately taken into account, since the calculations are done in terms of the Dar Zarrouk parameters derived from the exact resistivity distribution of the model. This enables one to compute the potential field by inverting a small sparse matrix. When the medium comprises only a few layers, the efficiency of the finite-difference model is comparable to that of the known analytical methods; for more complicated structures, however, the finite-difference model becomes more efficient. The accuracy of finite-difference results is demonstrated by comparing them with the corresponding analytically obtained data.

Notes: A method is given for solving the dc electric field problem of a point current source in an anisotropic 2 1/2-dimensional structural model. The surface integral equation of the field strength is given. Parallel to the strike the field strength is represented by a Fourier series. On the plane perpendicular to the strike each term of the field strength series is solved by means of the method of sub-sections, where linear behaviour of field strength over the sub-sections is assumed. Some numerical examples for different galvanic effects are given.

Notes: It is proposed that the vertical resolving power of a seismic signal is controlled by three aspects: the width of the central lobe, the side lobe ratio, and the side-tail oscillations. A comparative study of zero-phase signals covering the same frequency range shows that improvement of any one of these aspects inevitably leads to deterioration of one of the other aspects.An analytical simulation model is proposed of zero-phase signals free from side-tail oscillations, in which both the width of the central lobe and the side lobe ratio are adjustable. Analysis of the spectra of this model shows that, while the high frequency content of the spectrum is essential for obtaining a small width of the central lobe, the low frequency content of the spectrum plays an essential part in causing a low value of the side lobe ratio.

Notes: The objective of this study is to generate the separation-distance-domain (r-domain) transformation of the theoretically calculated wave number domain (m-domain) electromagnetic induction field component Bz(m, ω) of a stratified medium and to search for interpretive information which has been absent in the previously achieved numerical solutions of the problem.The r-domain kernel R̃(r, ω) function defining the induction field appears to adequately reflect the layering and electrical properties of the medium if it is expressed as a function of the frequency if the source-receiver separation r is small with respect to the thickness of the first layer. However, exact values of the conductivity cannot be distinguished from those of the neighboring values unless a resistive basement layer is present. This feature is the result of the truncation in series representation of the kernel function R̃(m, ω). However, this truncation is regarded as significant in the case of a conductive first layer. In m-domain static-zone studies, a conductive first layer slightly influences its r-domain correspondent.Although the computational cost of obtaining the kernel B(r, ω) by evaluation of the convolution in a cylindrical coordinate system is high, this semi-analytic solution is still superior to those based on the asymptotic assumptions.

Notes: A new method of estimating seismic stacking velocity from reflection seismograms is based on Fibonacci search technique and provides the highest rate of reduction of the interval of uncertainty of the stacking velocity. A review of the Fibonacci search strategy is presented, the application of the method is illustrated with synthetic and field examples.

Notes: The paper relates primarily to the borehole and the side bed correction charts for Latero-logs 3 and 7. Versions of some of these charts published by different companies—or even by the same company in different years—exhibit significant variations. Usually, such publications do not contain adequate information on how the charts were constructed and do not explain why discrepancies occur.Because of these reasons, an attempt has been made in this paper to reconstruct the borehole correction chart for Laterolog 7 and the shoulder bed correction charts for Latero-logs 3 and 7. For the latter two, the results found differ substantially from those published earlier.The paper demonstrates how departure (response) curves and correction charts for the lateral and the Laterolog 7 sondes can be computed from those for the normal sonde. An apparent resistivity formula is suggested for Laterolog 7 in which all currents that exist in the ground at the time of measurement and that produce the signal are monitored and used. Response curves and correction charts for Laterolog 7, based on such a formula, are presented as illustrations.

Notes: The purpose of the automatic gain control in seismic amplifiers is to balance the slow decrease of the signal in such a manner that its energy does not exceed the capacity of the recording system. At the same time the interesting seismic content of the signal has to be preserved as undistortedly as possible. At first, the technical data of AGC circuits are calculated. The characteristic curves of circuits with one, two, and three time constants are computed. In circuits with two and more time constants an oscillating of the AGC is possible. In order to guarantee aperiodic operation, the ratio of the time constants must not fall below a certain value. As long as these technical conditions are complied with, the free choice of the largest time constant remains open and can be accommodated to the geophysical conditions.From the endeavour to balance the slow decrease of the signal as well as possible, an upper limit for the choice of the time constants can be derived. A lower limit is obtained from the condition that the seismic content of the signal has to be preserved. The determinant time constant should lie between the two limits and differ from them as much as possible.Finally, the problem of the amplifier “squeezed” by energy pulses is touched.

Notes: Book Review in This Article:P. F. Shokin, Gravimetry (Apparatus and Methods for Measuring Gravity)

Notes: The paper deals with quantitative seismic measurements near underwater explosions. The blastings were carried out in an artificial small pond, the records were taken in adits, situated vertically below the charge. The range of charges extended from one detonator to 200 g of Ammon-Gelit explosive.Conventional seismic scaling by comparing amplitude and size of charge does not yield a simple power law, the exponent being larger for smaller charges and vice versa. This result is due to the different frequency-spectra of the seismic pulses, as shown by harmonic analysis. In contrast to this, the seismic energy as calculated from the records is directly proportional to the size of charge over the whole range.During the Lago Lagorai experiments in 1962 some quantitative seismic measurements near the shot point were also carried out. The relevant results are compared with the preceding ones and some differences are discussed.Some conclusions can be drawn:〈list xml:id="l1" style="custom"〉1The normal methodes, investigating the amplitude only, gives in many cases no clear description; this is especially true for nearby measurements with widely varying frequencies. Therefore it is suggested to extend conventional seismic scaling by including information on the frequency-spectrum and the kinetic energy of the seismic signal.2In order to get clear experimental data for theoretical investigations, it is necessary to extend the recording over a half-space, i.e. in adits or boreholes.3Influences of shape and size of the lake, in which the shots are fired, should be taken into account, too.

Notes: The magnitude of the streaming potential due to the passage of a liquid through a porous medium is examined, under conditions similar to those found in an aquifer under the action of a pumping well. Three models simulate flow in channels, conduits, and unconfined aquifers for several grain sizes of sands and for several resistivities of fluids. The ratio of the streaming potential to the pressure difference is constant for a selected sand and fluid, decreases as grain size increases, is essentially independent of the geometry of the flow, increases slightly as the permeability decreases, and decreases as the salt concentration increases. Extremely low streaming potentials can be expected near a pumping well.

Notes: Book received in this Articles:P. E. Potter and F. J. Pettijohn, Paleoccurrents and Basin Analysis

Notes: A method is described which allows to measure the elastic wave motion in the “interior” of two-dimensional solid models. It is based on the measurements of the lateral deformations of a plate that are related to the state of compression in the plane of the plate. A capacitive detector measuring the motion has been developed.Wave front studies have been carried out in a half space, in two half spaces in contact and in a single-layered half space. The experimental results are compared with theory. Special attention has been paid to the head wave.

Notes: All sorts of organic matter preserved under anaerobic conditions and transformed in reducing environments may form components of natural crude oils; such oils are linked to sapropel deposits by their contents in porphyrins and trace metals.

Notes: Offshore reflection records, even if they are of medium quality, can be used to determine the thickness of unconsolidated sediments. The method is described and its limits are specified. An example of application referring to the Gulf of Lyons is given.

Notes: A transistorized combination of multivibrators is described, by which the gain is set according to a time programme. This equipment allows quantitative recording of seismic events with extremely large amplitude variations. Some possible applications of this recording system to seismic research are discussed.

Notes: The theoretical aspects of a general configuration of the tripotential prospecting method are described while particular cases of the method were described by Carpenter and Haberjam (1956) and Sarma (1961).

Notes: The accuracy of an airborne magnetic survey is limited by the following factors:〈list xml:id="l1" style="custom"〉1Slow (diurnal) variations of the earth's field.2Fast variations of the earth's field (earth field “noise”).3Drift in measuring equipment.4Magnetometer “noise” (electronics, orientors …).5External disturbances, miscompensation.6Irregularities in flight altitude.7Location errors.The relative importance of these different causes of errors is analyzed from two viewpoints:〈list xml:id="l2" style="custom"〉a)Direct interpretation of anomalies on actual records,b)Compilation of isogram maps and their quantitative interpretation (second derivative, reduction to the pole, …).In conclusion, these errors do not affect the direct interpretation of profiles of standard quality. For instance, if the average altitude of the plane above the magnetic bodies is 1000 m, a variation of its flight level of about 100 m does not introduce serious errors in the interpretation.On the other hand, compilation of contoured isogam maps is often difficult, and compensation of the previous errors is not always possible except by approximate, rule-of-thumb methods. Furthermore, when the interval between lines is greater than the depth of magnetic masses below the plane of flight, the contours are interpolated and do not represent the magnetic field. Sometimes the contouring can offer different solutions, and the map is therefore not objective; this could then result in errors larger than those from the other causes.To evaluate the quality of the map and its interpretation we must know the location of flight lines and the compilation process employed. It is also wise to avoid quantitative interpretation of small anomalies and limit oneself to a qualitative interpretation.

Notes: Books reviewed in this article: Geomagnetismus und Aeronomie, Vol. II, Edited by Prof. Dr. G. Fanselau“Geomagnetic instruments and measuring methods” (Geomagnetische Instrumente und Meßmethoden) by Dr. H. Wiese, Dr. H. Schmidt, Dr. O. Lucre, Dr. Dr. F. Frölich Lehrbuch der Angewandten Geologie (Textbook for applied geology). Edited by Prof. Dr. A. Bentz Band I: Allgemeine Methoden, Kartierung, Petrographie, Paläontologie, Geophysik, Bodenkunde, written by well known authorities Continental Drift, edited by S. K. Runcorn

Notes: For a given refraction time-distance curve, the range in thickness for a hidden intermediate layer is given together with the effect the layer has on the total thickness of the two layers above the recorded refractor.

Notes: The method of Far Terrain Corrections is described which permits contouring of terrain effects for distant topography; near terrain effects must be computed separately.The method is only slightly less accurate than standard graphical techniques and saves computing time. It is most useful in medium size surveys involving 100 to 2,000 observation points where the application of electronic computers is uneconomic.

Notes: Books reviewed in this article:Emmons, Allison, Stauffer, Thiel, Geology, Principles and Process, 5th EditionB. N. Ivakin, The Microstructure and Macrostructure of Elastic Waves

Notes: Book Review in This Article:Robert L. Miller and James Steven KahnYe. P. Fedorov, Nutation and Forced Motion of the Earth's Pole. Translated from the Russian by Bertha Swirles Jeffreys, Foreword by Sir Harold Jeffreys.

Notes: Case history of the use of fan filtering for improving reflection continuity without destroying their character. The field technique is described: wide-band, large dynamical range recording with a programmed gain control and a very slow A.G.C., small distance between trace centers, high cutoff wave-number.Although the total amount of mixing due to fan filtering is rather high, a broad spectrum was obtained and inverse convolution filtering was used to improve trace resolution.

Notes: Graticules are known for the calculation of the magnetic field of homogeneously magnetized “two-dimensional” structures. For bodies whose lateral dimensions are comparable with the dimensions of the cross section and/or the distance between the point of observation and the structure, these graticules allow an approximative computation of the field in the plane of symmetry only. The degree of approximation can be improved by means of end corrections, but the amount of work involved increases rapidly. Moreover, even with end corrections the applicability of the graticules is still restricted to cases of rather simple geometry.In this paper, a set of graticules is proposed which already incorporates all end corrections. The set consists of three graticules, and it can be shown that at any point of observation lying outside the body each graticule needs be applied once only in order to calculate any component of the magnetic field produced by a homogeneously magnetized cylinder of arbitrary cross section, finite lateral extension and arbitrary spatial orientation.Curves and tables have been prepared, which allow the construction of the graticules under consideration. The application is illustrated by a hypothetical example. Possibilities for further improvements of the method are discussed.

Notes: By this method an approximation of gravity-anomaly of an inhomogeneous mass with any form is calculated. The mass is inbedded in a homogeneous medium. The density of the medium differs from the density-distribution of the mass.

Notes: Book Review in this Article:H. Israel and A. Krebs, Nuclear Radiation in GeophysicsB. A. Tkhostov, Initial Rock Pressures in Oil and Gas DepositsJohn S. Steinhart and Robert P. Meyer, Explosion Studies of Continental Structure

Notes: Pour caractériser les anomalies de la carte initiate et de la carte transformeé, on définit des indices de netteté désingés respectivement par I0 et I et on étudie le rapport I/I0 pour diverses formules appliquées à trois anomalies typiques (sphère, anticlinal, faille). Les courbes obtenues permettent d'introduire, par analogie avec les circuits électriques, des notions telles que profondeur de coupure et pente.

Notes: Condition nécessaire et suffisante pour qu'un sismogramme obtenu à la surface ?un milieu stratifé puisse être considéré comme résultant de l'ensemble des réflexions, directes et multiples, subies par une onde plane de compression se propageant normalement aux strates, supposés parfaitement élastiques. Modification minimale à faire subir à un sismogramme donné pour qu'il satisfasse à cette condition.Possibilité, quand cette condition est satisfaite, de déduire du sismogramme la loi de variation de la vitesse des ondes élastiques dans le milieu considéré.Exposé détaillé du processus pratique sur un exemple et quelques autres résultats de son application.