ALBERT

Description: Effect of rapid pressure decay on solid propellant combustion

Description: The effect of mass addition on the flow over bodies moving at hypersonic speeds has been studied by several investigators (e.g., Cresci and Libby). In most of this work, primary attention logically has been directed toward the effects of foreign-gas injection on heat transfer and pressure distributions, and, principally for this reason, most of the work ha been done at zero angle of attack. The foreign gas can be provided either by some active injection system or by the action of an ablation heat shield. With increasing rates of injection, the basic flow about the body can be affected significantly. One such effect was observed in the paper by Cresci and Libby, where it was shown that the shockwave standoff distance can be increased by gas injection at the nose of a body.

Description: The greatest efficiency for a lifting surface at supersonic speeds, according to the theoretical considerations of reference 1, can be attained if the leading edge is swept well behind the Mach cone and the highest aspect ratio which is structurally possible is employed. Such a wing, designed for a Mach number of 3.0, would have 80 deg. of sweepback. Aeroelastic effects have 〈 been shown 3 to be considerable for a wing with 60deg of sweepback and designed for a Mach number of 2.0. The wing shown was found theoretically to have considerable loss in maximum lift-drag ratio attributable to aeroelasticity. This wing has 12-per cent-thick Clark-Y airfoils normal to the wing leading edge. If it were of solid aluminum and flying at a dynamic pressure of 2,400 lbs./sq.ft. (flexibility parameter qb(exp. 4) /El(0) = 7.8), analysis indicates that the wing would deflect so as to reduce the maximum lift-drag ratio about 30 per cent.

Description: A simplified method is presented for estimating the lift-curve slope of irregular planform wings at subsonic speeds and low angles of attack. The present process is an extension of the method derived in NACA Technical Note 3911 and enables quick estimates of subsonic liftcurve slope, to be made whereas more refined procedures require considerable time and computation. Comparison of experimental and estimated values for a wide range of wing planforms having discontinuous spanwise sweep variation indicates good agreement. A comparison of the present procedure with a 20-step vortex method (NACA Research Memorandum L50L13) indicated good agreement for a variable-sweep configuration.

Description: No abstract available

Description: The transonic similarity rules have been applied to the correlation of experimental data for a series of 22 rectangular wings having symmetrical NACA 63A-series sections, aspect ratios from 1/2 to 6, and thicknesses from 2 to 10 percent. The data were obtained by use of the transonic bump technique over a Mach number range from 0.40 to 1.10, corresponding to a Reynolds number range from 1.25 to 2.05 million. The results show that it is possible to correlate experimental data throughout the subsonic, transonic, and moderate supersonic regimes by using the transonic similarity parameters in forms which are consistent with the Prandtl-Glauert rule of linearized theory. The multiple families of basic data curves for the various aspect ratios and thickness ratios have been summarized in single presentations involving only one geometric variable - the product of the aspect ratio and the l/3 power of the thickness ratio.

Description: Experiments have been made at Stanford University to determine the performance characteristics of plane-wall, two-dimensional diffusers which were so proportioned as to insure reasonable approximation of two-dimensional flow. All of the diffusers had identical entrance cross sections and discharged directly into a large plenum chamber; the test program included wide variations of divergence angle and length. During all tests a dynamic pressure of 60 pounds per square foOt was maintained at the diffuser entrance and the boundary layer there was thin and fully turbulent. The most interesting flow characteristics observed were the occasional appearance of steady, unseparated, asymmetric flow - which was correlated with the boundary-layer coalescence - and the rapid deterioration of flow steadiness - which occurred as soon as the divergence angle for maximum static pressure recovery was exceeded. Pressure efficiency was found to be controlled almost exclusively by divergence angle, whereas static pressure recovery was markedly influenced by area ratio (or length) as well as divergence angle. Volumetric efficiency. diminished as area ratio increased, and at a greater rate with small lengths than with large ones. Large values of the static-pressure-recovery coefficient were attained only with long diffusers of large area ratio; under these conditions pressure efficiency was high and. volumetric efficiency low. Auxiliary tests with asymmetric diffusers demonstrated that longitudinal pressure gradient, rather than wall divergence angle, controlled flow separation. Others showed that the addition of even a short exit duct of uniform section augmented pressure recovery. Finally, it was found that the installation of a thin, central, longitudinal partition suppressed flow separation in short diffusers and thereby improved pressure recovery

Description: Recent developments in airfoil-testing methods and fundamental air-flow investigations, as applied to airfoils, are discussed. Preliminary test results, obtained under conditions relatively free from stream turbulence and other disturbances, are presented. Suitable airfoils and airfoil-design principles were developed to take advantage of the unusually extensive laminar boundary layers that may be maintained under the improved testing conditions. The results are of interest mainly in range of below 6,000,000.

Description: Simultaneous air-flow photographs and pressure-distribution measurements have been made of the NACA 4412 airfoil at high speeds in order to determine the physical nature of the compressibility burble. The flow photographs were obtained by the Schlieren method and the pressures were simultaneously measured for 54 stations on the 5-inch-chord wing by means of a multiple-tube photographic manometer. Pressure-measurement results and typical Schlieren photographs are presented. The general nature of the phenomenon called the "compressibility burble" is shown by these experiments. The source of the increased drag is the compression shock that occurs, the excess drag being due to the conversion of a considerable amount of the air-stream kinetic energy into heat at the compression shock.

Description: A method is presented for the estimation of the subsonic-flight-speed characteristics of sharp-lip inlets applicable to supersonic aircraft. The analysis, based on a simple momentum balance consideration, permits the computation of inlet pressure recovery - mass-flow relations and additive-drag coefficients for forward velocities from zero to the speed of sound. The penalties for operation of a sharp-lip inlet at velocity ratios other than 1.0 may be severe; at lower velocity ratios an additive drag is incurred that is not cancelled by lip suction, while at higher velocity ratios, unavoidable losses in inlet total pressure will result. In particular, at the take-off condition, the total pressure and the mass flow for a choked inlet are only 79 percent of the values ideally attainable with a rounded lip. Experimental data obtained at zero speed with a sharp-lip supersonic inlet model were in substantial agreement with the theoretical results.