ALBERT

Beschreibung: This paper presents design and testing of a shell-encapsulated solar collector which can be used in north area of China for wall-amounting installation. The designed solar collector is based on the combination of a novel compound curved surface concentrator and an aluminum concentric solar receiver, which is contained in a glass evacuated-tube. As there is no perforative joint between the double-skin glass evacuated-tube and the aluminum concentric solar receiver, the difficulty of vacuum keeping for a glass-metal joint is avoided. The cavity shell provides an additional thermal insulation to reduce heat loss of the designed solar collector. The working principle of the compound curved surface concentrator is described. The ray-tracing results are given to show the effect of deviation angle of the concentrator on its optical efficiency, hence determining its maximum acceptance angle. A prototype of the designed solar collector has been constructed and tested under the sunny winter weather condition. The experimental results indicate that the hot water temperature higher than 80°C with a daily average efficiency of about 45~50% has been achieved at the average ambient temperature below 0°C, so the designed solar collector can produce hot water at a useful temperature in winter.

Beschreibung: A novel all-glass evacuated tube collector manifold header with an inserted tube is proposed in this paper which makes water in all-glass evacuated solar collector tube be forced circulated to improve the performance of solar collector. And a dynamic numerical model was presented for the novel all-glass evacuated tube collector manifold header water heater system. Also, a test rig was built for model validation and comparison with traditional all-glass evacuated tube collector. The experiment results show that the efficiency of solar water heater with a novel collector manifold header is higher than traditional all-glass evacuated tube collector by about 5% and the heat transfer model of water heater system is valid. Based on the model, the relationship between the average temperature of water tank and inserted tube diameter (water mass flow) has been studied. The results show that the optimized diameter of inserted tube is 32 mm for the inner glass with the diameter of 47 mm and the water flow mass should be less than 1.6 Kg/s.

Beschreibung: The performance of a dual-function solar collector (DFSC) that can work as either water heater or air heater depending on seasonal requirement is investigated via both experimental and numerical approaches in this paper. The numerical results are well consistent with the experimental results. Daily efficiency of the thermosiphon system with DFSC is more than 55% in water heating mode and the instantaneous air heating efficiency of the collector reaches 60%. The effects of inner parameters on the thermal efficiency of the collector are analyzed by numerical simulations of the operation of DFSC in two working modes. It is found that the depths of the two air channels in DFSC have an optimal range suitable for both working modes. The thickness of back insulation should be no less than 0.06 m to prevent heat loss via backboard, and the diameter and number of copper tubes show notable effect on the efficiency of DFSC in water heating mode but slight effect in air heating mode.

Beschreibung: Nuclear power plants are highly complex systems and the issues related to their safety are of primary importance. Probabilistic safety assessment is regarded as the most widespread methodology for studying the safety of nuclear power plants. As maintenance is one of the most important factors for affecting the reliability and safety, an enhanced preventive maintenance optimization model based on a three-stage failure process is proposed. Preventive maintenance is still a dominant maintenance policy due to its easy implementation. In order to correspond to the three-color scheme commonly used in practice, the lifetime of system before failure is divided into three stages, namely, normal, minor defective, and severe defective stages. When the minor defective stage is identified, two measures are considered for comparison: one is that halving the inspection interval only when the minor defective stage is identified at the first time; the other one is that if only identifying the minor defective stage, the subsequent inspection interval is halved. Maintenance is implemented immediately once the severe defective stage is identified. Minimizing the expected cost per unit time is our objective function to optimize the inspection interval. Finally, a numerical example is presented to illustrate the effectiveness of the proposed models.

Beschreibung: An integrated deterministic and probabilistic safety analysis (IDPSA) was carried out to assess the performances of the firefighting means to be applied in a nuclear power plant. The tools used in the analysis are the code FDS (Fire Dynamics Simulator) for fire simulation and the tool MCDET (Monte Carlo Dynamic Event Tree) for handling epistemic and aleatory uncertainties. The combination of both tools allowed for an improved modelling of a fire interacting with firefighting means while epistemic uncertainties because lack of knowledge and aleatory uncertainties due to the stochastic aspects of the performances of the firefighting means are simultaneously taken into account. The MCDET-FDS simulations provided a huge spectrum of fire sequences each associated with a conditional occurrence probability at each point in time. These results were used to derive probabilities of damage states based on failure criteria considering high temperatures of safety related targets and critical exposure times. The influence of epistemic uncertainties on the resulting probabilities was quantified. The paper describes the steps of the IDPSA and presents a selection of results. Focus is laid on the consideration of epistemic and aleatory uncertainties. Insights and lessons learned from the analysis are discussed.

Beschreibung: In this paper we evaluate the impact of a power uprate on a pressurized water reactor (PWR) for a tsunami-induced flooding test case. This analysis is performed using the RISMC toolkit: the RELAP-7 and RAVEN codes. RELAP-7 is the new generation of system analysis codes that is responsible for simulating the thermal-hydraulic dynamics of PWR and boiling water reactor systems. RAVEN has two capabilities: to act as a controller of the RELAP-7 simulation (e.g., component/system activation) and to perform statistical analyses. In our case, the simulation of the flooding is performed by using an advanced smooth particle hydrodynamics code called NEUTRINO. The obtained results allow the user to investigate and quantify the impact of timing and sequencing of events on system safety. In addition, the impact of power uprate is determined in terms of both core damage probability and safety margins.

Beschreibung: In case of some nuclear power plants constructed at the soft soil sites, liquefaction should be analysed as beyond design basis hazard. The aim of the analysis is to define the postevent condition of the plant, definition of plant vulnerabilities, and identification of the necessary measures for accident management. In the paper, the methodology of the analysis of liquefaction effects for nuclear power plants is outlined. The procedure includes identification of the scope of the safety analysis and the acceptable limit cases for plant structures having different role from accident management point of view. Considerations are made for identification of dominating effects of liquefaction. The possibility of the decoupling of the analysis of liquefaction effects from the analysis of vibratory ground motion is discussed. It is shown in the paper that the practicable empirical methods for definition of liquefaction susceptibility provide rather controversial results. Selection of method for assessment of soil behaviour that affects the integrity of structures requires specific considerations. The case of nuclear power plant at Paks, Hungary, is used as an example for demonstration of practical importance of the presented results and considerations.

Beschreibung: The loss of off-site power (LOOP) event occurs when all electrical power to the nuclear power plant from the power grid is lost. Complete failure of both off-site and on-site alternating current (AC) power sources is referred to as a station blackout (SBO). Combined LOOP and SBO events are analyzed in this paper. The analysis is done for different time delays between the LOOP and SBO events. Deterministic safety analysis is utilized for the assessment of the plant parameters for different time delays of the SBO event. Obtained plant parameters are used for the assessment of the probabilities of the functional events in the SBO event tree. The results show that the time delay of the SBO after the LOOP leads to a decrease of the core damage frequency (CDF) from the SBO event tree. The reduction of the CDF depends on the time delay of the SBO after the LOOP event. The results show the importance of the safety systems to operate after the plant shutdown when the decay heat is large. Small changes of the basic events importance measures are identified with the introduction of the delay of the SBO event.

Beschreibung: Concentrator solar cells that operate at high solar concentration level must be cooled. In this paper, direct liquid immersion cooling of triple-junction solar cells (InGaP/InGaAs/Ge) is proposed as a heat dissipation solution for dense-array high concentrating photovoltaic (HCPV) systems. The advantages of triple-junction CPV cells immersed in a circulating dielectric liquid and dish HCPV technology are integrated into a CPV system to improve the system electrical conversion efficiency. An analytical model for the direct liquid-immersed solar receiver with triple-junction CPV cells is presented. The main outputs of the model are the components temperatures of the receiver and the system electrical efficiency. The influence of concentration factor, mass flow rate, and inlet liquid temperature on the operating temperature of the triple-junction CPV cells and the system electrical conversion efficiency are discussed. It is shown that the system electrical conversion efficiency is very high for a wide range of operating conditions. The three operating parameters have a major effect on the operating temperature of the triple-junction CPV cells and, by extension, system output power. The flow rate selection should match concentration factor to keep the triple-junction CPV cells temperature lower and increase the electrical conversion efficiency of the dense-array HCPV system.

Beschreibung: Solar aided coal-fired power generation system (SACFPGS) combines solar energy and traditional coal-fired units in a particular way. This study mainly improves the solar thermal storage system. Genetic algorithm is used to optimize the SACFPGS. The best integration approach of the system, the collector area, and the corresponding thermal storage capacity to replace each high-pressure extraction are obtained when the amount of coal saving in unit solar investment per hour is at its largest. System performance before and after the improvement is compared. Results show that the improvement of the thermal storage system effectively increases the economic benefit of the integrated system.

Beschreibung: A spectral selectivity surface for both solar heating and radiative cooling was proposed. It has a high spectral absorptivity (emissivity) in the solar radiation band and atmospheric window band (i.e., 0.2~3 μm and 8~13 μm), as well as a low absorptivity (emissivity) in other bands aside from the solar radiation and atmospheric window wavelengths (i.e., 3~8 μm or above 13 μm). A type of composite surface sample was trial-manufactured combining titanium-based solar selective absorbing coating with polyethylene terephthalate (TPET). Sample tests showed that the TPET composite surface has clear spectral selectivity in the spectra of solar heating and radiation cooling wavelengths. The equilibrium temperatures of the TPET surface under different sky conditions or different inclination angles of surface were tested at both day and night. Numerical analysis and comparisons among the TPET composite surface and three other typical surfaces were also performed. These comparisons indicated that the TPET composite surface had a relative heat efficiency of 76.8% of that of the conventional solar heating surface and a relative temperature difference of 75.0% of that of the conventional radiative cooling surface, with little difference in cooling power.

Beschreibung: In this paper, taking Lushan West Sea highway green rest area in Jiangxi Province of China as the case study, the suitable types, applicability, advantages, and effective methods of solar lighting technologies for highway rest area were determined based on the analysis of characteristics of highway green rest area. It was proved that solar lighting technologies including the natural light guidance system, solar LED lighting, and maximizing natural light penetration were quite suitable for highway rest area in terms of lighting effects and energy and economic efficiency. The illuminance comparison of light guidance system with electrical lighting was made based on the on-site experiment. Also, the feasibility of natural light guidance system was well verified in terms of the lighting demand of the visitor centre in the rest area by the illuminance simulation analysis. The evaluation of the energy saving, economic benefits, and environmental effects of solar lighting technologies for highway rest area was, respectively, made in detail. It was proved that the application of solar technology for green lighting of highway rest facilities not only could have considerable energy saving capacity and achieve high economic benefits, but also make great contributions to the reduction of environment pollution.

Beschreibung: Integrated Deterministic-Probabilistic Safety Assessment (IDPSA) combines deterministic model of a nuclear power plant with a method for exploration of the uncertainty space. Huge amount of data is generated in the process of such exploration. It is very difficult to “manually” process and extract from such data information that can be used by a decision maker for risk-informed characterization, understanding, and eventually decision making on improvement of the system safety and performance. Such understanding requires an approach for interpretation, grouping of similar scenario evolutions, and classification of the principal characteristics of the events that contribute to the risk. In this work, we develop an approach for classification and characterization of failure domains. The method is based on scenario grouping, clustering, and application of decision trees for characterization of the influence of timing and order of events. We demonstrate how the proposed approach is used to classify scenarios that are amenable to treatment with Boolean logic in classical Probabilistic Safety Assessment (PSA) from those where timing and order of events determine process evolution and eventually violation of safety criteria. The efficiency of the approach has been verified with application to the SARNET benchmark exercise on the effectiveness of hydrogen management in the containment.

Beschreibung: The analytical/deterministic modelling and simulation/probabilistic methods are used separately as a rule in order to analyse the physical processes and random or uncertain events. However, in the currently used probabilistic safety assessment this is an issue. The lack of treatment of dynamic interactions between the physical processes on one hand and random events on the other hand causes the limited assessment. In general, there are a lot of mathematical modelling theories, which can be used separately or integrated in order to extend possibilities of modelling and analysis. The Theory of Probabilistic Dynamics (TPD) and its augmented version based on the concept of stimulus and delay are introduced for the dynamic reliability modelling and the simulation of accidents in hybrid (continuous-discrete) systems considering uncertain events. An approach of non-Markovian simulation and uncertainty analysis is discussed in order to adapt the Stimulus-Driven TPD for practical applications. The developed approach and related methods are used as a basis for a test case simulation in view of various methods applications for severe accident scenario simulation and uncertainty analysis. For this and for wider analysis of accident sequences the initial test case specification is then extended and discussed. Finally, it is concluded that enhancing the modelling of stimulated dynamics with uncertainty and sensitivity analysis allows the detailed simulation of complex system characteristics and representation of their uncertainty. The developed approach of accident modelling and analysis can be efficiently used to estimate the reliability of hybrid systems and at the same time to analyze and possibly decrease the uncertainty of this estimate.

Beschreibung: We demonstrate an innovative CIGS-based solar cells model with a graded doping concentration absorber profile, capable of achieving high efficiency values. In detail, we start with an in-depth discussion concerning the parametrical study of conventional CIGS solar cells structures. We have used the wxAMPS software in order to numerically simulate cell electrical behaviour. By means of simulations, we have studied the variation of relevant physical and chemical parameters—characteristic of such devices—with changing energy gap and doping density of the absorber layer. Our results show that, in uniform CIGS cell, the efficiency, the open circuit voltage, and short circuit current heavily depend on CIGS band gap. Our numerical analysis highlights that the band gap value of 1.40 eV is optimal, but both the presence of Molybdenum back contact and the high carrier recombination near the junction noticeably reduce the crucial electrical parameters. For the above-mentioned reasons, we have demonstrated that the efficiency obtained by conventional CIGS cells is lower if compared to the values reached by our proposed graded carrier concentration profile structures (up to 21%).

Beschreibung: Microcrystalline silicon (μc-Si:H) thin-film solar cells are processed on glass superstrates having both micro- and nanoscale surface textures. The microscale texture is realised at the glass surface, using the aluminium-induced texturing (AIT) method, which is an industrially feasible process enabling a wide range of surface feature sizes (i.e., 700 nm–3 μm) of the textured glass. The nanoscale texture is made by conventional acid etching of the sputter-deposited transparent conductive oxide (TCO). The influence of the resulting “double texture” on the optical scattering is investigated by means of atomic force microscopy (AFM) (studying the surface topology), haze measurements (studying scattering into air), and short-circuit current enhancement measurements (studying scattering into silicon). A predicted enhanced optical scattering efficiency is experimentally proven by a short-circuit current enhancement of up to 1.6 mA/cm2 (7.7% relative increase) compared to solar cells fabricated on a standard superstrate, that is, planar glass covered with nanotextured TCO. Enhancing the autocorrelation length (or feature size) of the AIT superstrates might have the large potential to improve the μc-Si:H thin-film solar cell efficiency, by reducing the shunting probability of the device while maintaining a high optical scattering performance.

Beschreibung: We study the electrical and the optical behavior of HIT solar cell by means of measurements and optoelectrical simulations by TCAD simulations. We compare the HIT solar cell with a conventional crystalline silicon solar cell to identify the strengths and weaknesses of the HIT technology. Results highlight different mechanisms of electrical and optical efficiency losses caused by the presence of the amorphous silicon layer. The higher resistivity of the a-Si layers implies a smaller distance between the metal lines that causes a higher shadowing. The worst optical coupling between the amorphous silicon and the antireflective coating implies a slight increase of reflectivity around the 600 nm wavelength.

Beschreibung: The hydrogenated amorphous silicon (a-Si:H)/hydrogenated microcrystalline silicon (c-Si:H) double p-type window layer has been developed and applied for improving microcrystalline silicon-germanium p-i-n single-junction thin-film solar cells deposited on textured SnO2:F-coated glass substrates. The substrates of SnO2:F, SnO2:F/c-Si:H(p), and SnO2:F/a-Si:H(p) were exposed to H2 plasma to investigate the property change. Our results showed that capping a thin layer of a-Si:H(p) on SnO2:F can minimize the Sn reduction during the deposition process which had H2-containing plasma. Optical measurement has also revealed that a-Si:H(p) capped SnO2:F glass had a higher optical transmittance. When the 20 nm c-Si:H(p) layer was replaced by a 3 nm a-Si:H(p)/17 nm c-Si:H(p) double window layer in the cell, the conversion efficiency () and the short-circuit current density () were increased by 16.6% and 16.4%, respectively. Compared to the standard cell with the 20 nm c-Si:H(p) window layer, an improved conversion efficiency of 6.19% can be obtained for the cell having a-Si:H(p)/c-Si:H(p) window layer, with  = 490 mV,  = 19.50 mA/cm2, and FF = 64.83%.

Beschreibung: Atomic layer deposition was used to coat CdS photoanodes with 7 nm thick TiO2 films to protect them from photocorrosion during photoelectrochemical water splitting. Photoelectrochemical measurements indicate that the TiO2 coating does not provide full protection against photocorrosion. The degradation of the film initiates from small pinholes and shows oscillatory behavior that can be explained by an Avrami-type model for photocorrosion that is halfway between 2D and 3D etching. XPS analysis of corroded films indicates that a thin layer of CdS remains present on the surface of the corroded photoanode that is more resilient towards photocorrosion.

Beschreibung: A new trough solar concentrator which is composed of multiple reflection surfaces is developed in this paper. The concentrator was analyzed firstly by using optical software. The variation curves of the collecting efficiency affected by tracking error and the deviation angle were given out. It is found that the deviation tolerance for the collector tracking system is about 8 degrees when the receiver is a 90 mm flat. The trough solar concentrators were tested under real weather conditions. The experiment results indicate that, the new solar concentrator was validated to have relative good collecting efficiency, which can be more than 45 percent when it operated in more 145°C. It also has the characteristics of rdust, wind, and snow resistance and low tracking precision requirements.

Beschreibung: Several studies have found that the decrease of photovoltaic (PV) cell temperature would increase the solar-to-electricity conversion efficiency. Water type PV/thermal (PV/T) system was a good choice but it could become freezing in cold areas of Northern China. This paper proposed a simple combination of common-used PV panel and heat pipe, called PV-heat pipe (PV-HP) solar collector, for both electrical and thermal energy generation. A simplified one-dimensional steady state model was developed to study the electrical and thermal performance of the PV-HP solar collector under different solar radiations, water flow rates, and water temperatures at the inlet of manifold. A testing rig was conducted to verify the model and the testing data matched very well with the simulation values. The results indicated that the thermal efficiency could be minus in the afternoon. The thermal and electrical efficiencies decreased linearly as the inlet water temperature and water flow rate increased. The thermal efficiency increased while the electrical efficiency decreased linearly as the solar radiation increased.

Beschreibung: In integrated deterministic and probabilistic safety analysis (IDPSA), safe scenarios and prime implicants (PIs) are generated by simulation. In this paper, we propose a novel postprocessing method, which resorts to a risk-based clustering method for identifying Near Misses among the safe scenarios. This is important because the possibility of recovering these combinations of failures within a tolerable grace time allows avoiding deviations to accident and, thus, reducing the downtime (and the risk) of the system. The postprocessing risk-significant features for the clustering are extracted from the following: (i) the probability of a scenario to develop into an accidental scenario, (ii) the severity of the consequences that the developing scenario would cause to the system, and (iii) the combination of (i) and (ii) into the overall risk of the developing scenario. The optimal selection of the extracted features is done by a wrapper approach, whereby a modified binary differential evolution (MBDE) embeds a -means clustering algorithm. The characteristics of the Near Misses scenarios are identified solving a multiobjective optimization problem, using the Hamming distance as a measure of similarity. The feasibility of the analysis is shown with respect to fault scenarios in a dynamic steam generator (SG) of a nuclear power plant (NPP).

Beschreibung: System codes for simulation of safety performance of nuclear plants may contain parameters whose values are not known very accurately. New information from tests or operating experience is incorporated into safety codes by a process known as calibration, which reduces uncertainty in the output of the code and thereby improves its support for decision-making. The work reported here implements several improvements on classic calibration techniques afforded by modern analysis techniques. The key innovation has come from development of code surrogate model (or code emulator) construction and prediction algorithms. Use of a fast emulator makes the calibration processes used here with Markov Chain Monte Carlo (MCMC) sampling feasible. This work uses Gaussian Process (GP) based emulators, which have been used previously to emulate computer codes in the nuclear field. The present work describes the formulation of an emulator that incorporates GPs into a factor analysis-type or pattern recognition-type model. This “function factorization” Gaussian Process (FFGP) model allows overcoming limitations present in standard GP emulators, thereby improving both accuracy and speed of the emulator-based calibration process. Calibration of a friction-factor example using a Method of Manufactured Solution is performed to illustrate key properties of the FFGP based process.

Beschreibung: Construction and characterization of an inflatable mirror prototype made out of flexible polymeric membranes are being presented. Surfaces were curved by imposing a slight excess of air pressure. Lightweighted, lowcost, and commercially available materials were selected in order to produce solar concentration elements at competitive prices. In this sense, large-area, image-forming mirrors with low optical acuity were achieved by concentration purposes. Optical characterization of the mirror’s shape at a given pressure or curvature radius was done by means of a structuredlight technique with a resolution of 0.1 mm finding a conical shape acquired by the inflated mirror as the best approximation. Concentration ratio achieved for a focal length of 5068 mm was of 25.1 suns, making a promising approach for lowering initial investment costs in applications such as hot-water, parabolic dish with Stirling engines, or concentrated photovoltaic electricity generation.

Beschreibung: This paper presents the results of the analysis of the Unprotected Loss of Flow (ULOF) experiment SHRT-45R performed in the EBR-II fast reactor. These experiments are being analyzed in the scope of a benchmark exercise coordinated by the IAEA. The SHRT-45R benchmark contains a neutronic and a thermal-hydraulic part and results are presented for both. Neutronic calculations are performed with the ERANOS2.0 code in combination with various sets of nuclear data. The thermal-hydraulic evaluation is done with RELAP5-3D. The results are that the major neutronic parameters are well predicted with error margins on the order of 1%. The thermal-hydraulic results are less favourable: a consistent overestimation of the outlet temperature occurs in combination with erroneous flow distribution. Observed differences with measured data cannot be explained easily. The work presented in this paper was undertaken to investigate and validate the effectiveness of the calculational tools and data that are commonly used in our lab for the design and analysis of liquid metal cooled fast reactors.

Beschreibung: Green synthesis of metallic particles has become an economic way to improve and protect the environment by decreasing the use of toxic chemicals and eliminating dyes. The synthesis of metal particles is gaining more importance due to its simplicity, rapid rate of synthesis of particles, and environmentally friendly. The present work aims to report a novel and environmentally friendly method for the synthesis of iron particles using deoiled Pimenta dioica L. Merrill husk as support. The indigo carmine removal efficiency by ozonation and catalyzed ozonation is also presented. Synthesized materials were characterized by N2 physisorption and scanning electron microscopy (SEM/EDS). By UV-Vis spectrophotometry the removal efficiency of indigo carmine was found to be nearly 100% after only 20 minutes of treatment under pH 3 and with a catalyst loading of 1000 mgL−1. Analytical techniques such as determination of the total organic carbon content (TOC) and chemical oxygen demand (COD) showed that iron particles supported on deoiled Pimenta dioica L. Merrill husk can be efficiently employed to degrade indigo carmine and achieved a partial mineralization (conversion to CO2 and H2O) of the molecule. From the results can be inferred that the prepared biocomposite increases the hydroxyl radicals generation.

Beschreibung: The individual methods of disinfection peracetic acid (PAA) and UV radiation and combined process PAA/UV in water (synthetic) and sanitary wastewater were employed to verify the individual and combined action of these advanced oxidative processes on the effectiveness of inactivation of microorganisms indicators of fecal contamination E. coli, total coliforms (in the case of sanitary wastewater), and coliphages (such as virus indicators). Under the experimental conditions investigated, doses of 2, 3, and 4 mg/L of PAA and contact time of 10 minutes and 60 and 90 s exposure to UV radiation, the results indicated that the combined method PAA/UV provided superior efficacy when compared to individual methods of disinfection.

Beschreibung: The big advantage of LED is the flexible spectral design to make white light using different color mixing schemes. Recently, the color mixing of RGB LEDs is mostly done by sealing all three chips at single package and regulated the mix ratio of these three colors to produce the color of light. And, by changing the LEDs array alignment, RGB chips can achieve overlapping colors of light and create the fun of changing colors in light mixing. Therefore, the purpose of this study is to propose an innovative technique of light mixing. By applying the mechanism design, a RGB light mixing mechanism is produced. Each of the RGB LEDs lamp-type is installed on the couple link of the three mechanisms, respectively. By driving a crank makes the couple link and an output link to produce the relative motion, this will result in the fact that the RGB lamps can project lights on the same plane in order to obtain the color mixing. Unlike mixing technique by control system, this design generates light mixing and changes of color with the synchronized driving of three mechanisms, thus achieving the dazzling perception of single-color lights or mixing of multiple colors for creating ambience of a space.

Beschreibung: We report on the photodegradation of diclofenac (DCF) by hydrothermal anatase nanocrystals either free or immobilized in porous silica matrix (TS) in connection to the type and amount of reactive oxygen species (ROS), in order to have deeper insight into their role in the photocatalysis and to provide an effective tool to implement the DCF mineralization. TiO2 and TS exhibit a remarkable efficiency in the DCF abatement, supporting that the utilization of anatase nanoparticles with the highly reactive , , and exposed surfaces can be an effective way for enhancing the photooxidation even of the persistent pollutants. Furthermore, the hydrothermal TiO2, when immobilized in silica matrix, preserves its functional properties, combining high photoactivity with an easy technical use and recovery of the catalyst. The catalysts performances have been related to the presence of OH•, , and species by electron paramagnetic resonance spin-trap technique. The results demonstrated that the ROS concentration increases with the increase of photoactivity and indicated a significant involvement of in the DCF degradation. The efficacy of TiO2 when immobilized on a silica matrix was associated with the high ROS life time and with the presence of singlet oxygen, which contributes to the complete photomineralization of DCF.

Beschreibung: This paper reports two numerical simulation methods for modeling displacement instabilities around a surface groove in a metal substrate used in nuclear power plant. The amplitude change in the groove, the downward displacement at the base node, and the groove displacement at the periphery were simulated using ABAQUS to compare the results from two methods, as well as the tangential stress in the elements at the groove base and periphery. The comparison showed that for the tangential stress two methods were in close agreement for all thermal cycles. For the amplitude change, the downward displacement, the groove displacement, and the stress distribution, the two methods were in close agreement for the first 3 to 6 thermal cycles. After that, inconsistency increased with the number of thermal cycles. It is interesting that the thermal cycle at which the discrepancy between the two methods began to occur corresponded to a thermally grown oxide (TGO) thickness of 1 μm, which showed the accuracy of the present work over the classic method. It is concluded that the present work’s numerical simulation scheme worked better with a thinner TGO layer than the classic method and could overcome the limitation of TGO thickness by simulating any thickness.

Beschreibung: The aim of this work was to couple physical-chemical approaches with photocatalysis to reduce by a simple, inexpensive way the organic load of olive mill wastewater (OMW), mandatorily prior to the final discharge. Before irradiation, different sorbents were tested to remove part of the organic fraction, monitored by measuring chemical oxygen demand (COD) and polyphenols (PP). Different low-cost, safe materials were tested, that is, Y zeolite (ZY), montmorillonite, and sepiolite. Considerable decrease of organic load was obtained, with the highest abatement (40%) provided by ZY (10 g L−1 in 1 : 10 OMW). Use of the three sorbents, in particular ZY, was convenient compared to commercial activated carbons. UV light photocatalytic tests, performed using P25 TiO2 on ZY-treated OMW, yielded quantitative remediation (ca. 90%). Also solar light provided significative results, PP being lowered by 74% and COD by 56%. Sol-gel anatase TiO2 and N-doped anatase TiO2 were also tested, obtaining good results, around 80% PP and 40% COD. Finally, an integrated approach was experimented by ZY-supported anatase TiO2 (TiO2@ZY). This photoreactive sorbent allowed one-pot treatment of OMW significative abatements of PP (77%) and COD (39%) with only 1 g L−1 material, under solar light.

Beschreibung: Molybdenum (Mo) thin films are widely used as rear electrodes in copper indium gallium diselenide (CIGS) solar cells. The challenge in Mo deposition by magnetron sputtering lies in simultaneously achieving good adhesion to the substrates while retaining the electrical and optical properties. Bilayer Mo films, comprising five different thickness ratios of a high pressure (HP) deposited bottom layer and a low pressure (LP) deposited top layer, were deposited on 40 cm × 30 cm soda-lime glass substrates by DC magnetron sputtering. We focus on understanding the effects of the individual layer properties on the resulting bilayer Mo films, such as microstructure, surface morphology, and surface oxidation. We show that the thickness of the bottom HP Mo layer plays a major role in determining the micromechanical and physical properties of the bilayer Mo stack. Our studies reveal that a thicker HP Mo bottom layer not only improves the adhesion of the bilayer Mo, but also helps to improve the film crystallinity along the preferred [] direction. However, the surface roughness and the porosity of the bilayer Mo films are found to increase with increasing bottom layer thickness, which leads to lower optical reflectance and a higher probability for oxidation at the Mo surface.

Beschreibung: Instrumental neutron activation analysis (INAA) is a powerful technique for trace element determination in rocks. Nine alabaster samples were collected from Wadi El-Nakhil located at the intersection of lat. 26°10′50′′N and long. 34°03′40′′E, central Eastern Desert, Egypt, for investigation by INAA and Energy Depressive X-Ray Fluorescence (EDXRF). The samples were irradiated by thermal neutrons at the TRIGA Mainz research reactor at a neutron flux of 7 × 1011 n/cm2·s. Twenty-two elements were determined, namely, As, Ba, Ca, Co, Cr, Sc, Fe, Hf, K, Mg, Mn, Na, Rb, U, Zn, Zr, Lu, Ce, Sm, La, Yb, and Eu. The chemical analysis of alabaster indicated having high contents of CaO and MgO and LOI and low contents of SiO2, Al2O3, Na2O, K2O, MnO, and Fe2O3.

Beschreibung: This paper reports the results of sensitivity analysis of the multidimension, multigroup neutron diffusion NODAL3 code for the NEACRP 3D LWR core transient benchmarks (PWR). The code input parameters covered in the sensitivity analysis are the radial and axial node sizes (the number of radial node per fuel assembly and the number of axial layers), heat conduction node size in the fuel pellet and cladding, and the maximum time step. The output parameters considered in this analysis followed the above-mentioned core transient benchmarks, that is, power peak, time of power peak, power, averaged Doppler temperature, maximum fuel centerline temperature, and coolant outlet temperature at the end of simulation (5 s). The sensitivity analysis results showed that the radial node size and maximum time step give a significant effect on the transient parameters, especially the time of power peak, for the HZP and HFP conditions. The number of ring divisions for fuel pellet and cladding gives negligible effect on the transient solutions. For productive work of the PWR transient analysis, based on the present sensitivity analysis results, we recommend NODAL3 users to use radial nodes per assembly, axial layers per assembly, the maximum time step of 10 ms, and 9 and 1 ring divisions for fuel pellet and cladding, respectively.

Beschreibung: The double-ended guillotine break (DEGB) of the horizontal coaxial gas duct accident is a serious air ingress accident of the high temperature gas-cooled reactor pebble-bed module (HTR-PM). Because the graphite is widely used as the structure material and the fuel element matrix of HTR-PM, the oxidation analyses of this severe air ingress accident have got enough attention in the safety analyses of the HTR-PM. The DEGB of the horizontal coaxial gas duct accident is calculated by using the TINTE code in this paper. The results show that the maximum local oxidation of the matrix graphite of spherical fuel elements in the core will firstly reach  mol/m3 at about 120 h, which means that only the outer 5 mm fuel-free zone of matrix graphite will be oxidized out. Even at 150 h, the maximum local weight loss ratio of the nuclear grade graphite in the bottom reflectors is only 0.26. Besides, there is enough time to carry out some countermeasures to stop the air ingress during several days. Therefore, the nuclear grade graphite of the bottom reflectors will not be fractured in the DEGB of the horizontal coaxial gas duct accident and the integrity of the HTR-PM can be guaranteed.

Beschreibung: Three hydrocalumite-like compounds in a Ca/Al ratio of 2 containing nitrate and acetate anions in the interlaminar region were prepared by a simple, economic, and environmentally friendly method. The solids were characterized by X-ray powder diffraction (XRD), thermogravimetric (TG) analysis, nitrogen adsorption-desorption at −196°C, scanning electron microscopy (SEM), infrared spectroscopy (FTIR), and UV-Vis Diffuse Reflectance Spectroscopy (DRS). The catalytic activity of the calcined solids at 700°C was tested in the photodegradation of 2,4-dichlorophenoxyacetic acid (2,4-D) where 57% degradation of 2,4-D (40 ppm) and a mineralization percentage of 60% were accomplished within 150 minutes. The photocatalytic properties were attributed to mayenite hydration, since the oxide ions in the cages are capable of reacting with water to form hydroxide anions capable of breaking down the 2,4-D molecules.

Beschreibung: Gamma-ray measurements in various research fields require efficient detectors. One of these research fields is mass attenuation coefficients of different materials. Apart from experimental studies, the Monte Carlo (MC) method has become one of the most popular tools in detector studies. An NaI(Tl) detector has been modeled, and, for a validation study of the modeled NaI(Tl) detector, the absolute efficiency of 3 × 3 inch cylindrical NaI(Tl) detector has been calculated by using the general purpose Monte Carlo code MCNP-X (version 2.4.0) and compared with previous studies in literature in the range of 661–2620 keV. In the present work, the applicability of MCNP-X Monte Carlo code for mass attenuation of concrete sample material as building material at photon energies 59.5 keV, 80 keV, 356 keV, 661.6 keV, 1173.2 keV, and 1332.5 keV has been tested by using validated NaI(Tl) detector. The mass attenuation coefficients of concrete sample have been calculated. The calculated results agreed well with experimental and some other theoretical results. The results specify that this process can be followed to determine the data on the attenuation of gamma-rays with other required energies in other materials or in new complex materials. It can be concluded that data from Monte Carlo is a strong tool not only for efficiency studies but also for mass attenuation coefficients calculations.

Beschreibung: Photovoltaic (PV) energy is one of the most important energy sources since it is clean and inexhaustible. It is important to operate PV energy conversion systems in the maximum power point (MPP) to maximize the output energy of PV arrays. An MPPT control is necessary to extract maximum power from the PV arrays. In recent years, a large number of techniques have been proposed for tracking the maximum power point. This paper presents a comparison of different MPPT methods and proposes one which used a power estimator and also analyses their suitability for systems which experience a wide range of operating conditions. The classic analysed methods, the incremental conductance (IncCond), perturbation and observation (P&O), ripple correlation (RC) algorithms, are suitable and practical. Simulation results of a single phase NPC grid connected PV system operating with the aforementioned methods are presented to confirm effectiveness of the scheme and algorithms. Simulation results verify the correct operation of the different MPPT and the proposed algorithm.

Beschreibung: Concentrated sunlight that is transmitted by fiber optics has been used for generating electricity, heat, and daylight. On the other hand, multijunction photovoltaic cells provide high efficiency for generating electricity from highly concentrated sunlight. This study deals with designing and simulating a high-efficiency coupler, employing a mathematical model to connect sunlight with fiber optics for multiple applications. The coupler concentrates and distributes irradiated light from a primary concentrator. In this study, a parabolic dish was used as the primary concentrator, a coupler that contains nine components called a compound truncated pyramid and a cone (CTPC), all of which were mounted on a plate. The material of both the CTPC and the plate was BK7 optical glass. Fiber optics cables and multijunction photovoltaic cells were connected to the cylindrical part of the CTPC. The fibers would transmit the light to the building to provide heat and daylight, whereas multijunction photovoltaic cells generate electricity. Theoretical and simulation results showed high performance of the designed coupler. The efficiency of the coupler was as high as , whereas the rim angle of the dish increased to an optimum angle. Distributed sunlight in the coupler increased the flexibility and simplicity of the design, resulting in a system that provided concentrated electricity, heat, and lighting for residential buildings.

Beschreibung: Water-soluble graphitic hollow carbon nanorods (wsCNRs) are exploited for their light-driven photochemical activities under outdoor sunlight. wsCNRs were synthesized by a simple pyrolysis method from castor seed oil, without using any metal catalyst or template. wsCNRs exhibited the light-induced photochemical degradation of methylene blue used as a model pollutant by the generation of singlet oxygen species. Herein, we described a possible degradation mechanism of methylene blue under the irradiation of visible photons via the singlet oxygen-superoxide anion pathway.

Beschreibung: Considering dangerous environmental conditions, maintenance of radioactive equipment can be performed by remote handling maintenance (RHM) system. The RHM system is a sophisticated man-machine system. Therefore, human factors analysis is an inevitable aspect considered in guaranteeing successful and safe task performance. This study proposes an approach for integrated analysis of human factors in RHM so as to make the evaluating process more practical. In the approach, indicators of accessibility, health safety, and fatigue are analyzed using virtual human simulation technologies. The human error factors in the maintenance process are analyzed using the human error probability (HEP) based on the success likelihood index method- (SLIM-) analytic hierarchy process (AHP). The psychological factors level of maintenance personnel is determined with an expert scoring. The human factors for the entire RHM system are then evaluated using the interval method. An application example is present, and the application results show that the approach can support the evaluation of the human factors in RHM.

Beschreibung: Solar panels have become attractive in order to generate and supply electricity in commercial and residential applications. Their increased module efficiencies have caused not only a massive production but also a sensible drop on sale prices. Methods of characterization, instrumentation for in situ measurements, defect monitoring, process control, and performance are required. A temperature characterization method by means of thermograph analysis is exposed in this paper. The method was applied to multicrystalline modules, and the characterization was made with respect to two different variables, first a thermal transient and second a characterization with respect to the current. The method is useful in order to detect hot spots caused by mismatch conditions in electrical parameters. The description, results, and limitations of the proposed method are discussed.

Beschreibung: Fe-doped TiO2 (Fe/TiO2) film photocatalyst was prepared by sol-gel and dip-coating process to extend its photoresponsivity to the visible spectrum. To promote the CO2 reduction performance with the photocatalyst, some types of base materials used for coating Fe/TiO2, which were netlike glass fiber and Cu disc, were investigated. The characterization of prepared Fe/TiO2 film coated on netlike glass fiber and Cu disc was analyzed by SEM and EPMA. In addition, the CO2 reduction performance of Fe/TiO2 film coated on netlike glass disc, Cu disc, and their overlap was tested under a Xe lamp with or without ultraviolet (UV) light, respectively. The results show that the concentration of produced CO increases by Fe doping irrespective of base material used under the illumination condition with UV light as well as that without UV light. Since the electron transfer between two overlapped photocatalysts is promoted, the peak concentration of CO for the Fe/TiO2 double overlapping is approximately 1.5 times as large as the Fe/TiO2 single overlapping under the illumination condition with UV light, while the promotion ratio is approximately 1.1 times under that without UV light.

Beschreibung: Based on the special application of 90-degree elbow pipe in the HTR-PM, the large eddy simulation was selected to calculate the instantaneous flow field in the 90-degree elbow pipe combining with the experimental results. The characteristics of the instantaneous turbulent flow field under the influence of flow separation and secondary flow were studied by analyzing the instantaneous pressure information at specific monitoring points and the instantaneous velocity field on the cross section of the elbow. The pattern and the intensity of the Dean vortex and the small scale eddies change over time and induce the asymmetry of the flow field. The turbulent disturbance upstream and the flow separation near the intrados couple with the vortexes of various scales. Energy is transferred from large scale eddies to small scale eddies and dissipated by the viscous stress in the end.

Beschreibung: Korea Atomic Energy Research Institute (KAERI) started the experimental research on moderator circulation as one of a the national research and development programs from 2012. This research program includes the construction of the moderator circulation test (MCT) facility, production of the validation data for self-reliant computational fluid dynamics (CFD) tools, and development of optical measurement system using the particle image velocimetry (PIV). In the present paper we introduce the scaling analysis performed to extend the scaling criteria suitable for reproducing thermal-hydraulic phenomena in a scaled-down CANDU- (CANada Deuterium Uranium-) 6 moderator tank, a manufacturing status of the 1/4 scale moderator tank. Also, preliminary CFD analysis results for the full-size and scaled-down moderator tanks are carried out to check whether the moderator flow and temperature patterns of both the full-size reactor and scaled-down facility are identical.

Beschreibung: The internal impedances of different dye-sensitized solar cell (DSSC) models were analyzed by electrochemical impedance spectrometer (EIS) with an equivalent circuit model. The Nyquist plot was built to simulate the redox reaction of internal device at the heterojunction. It was useful to analyze the component structure and promote photovoltaic conversion efficiency of DSSC. The impedance of DSSC was investigated and the externally connected module assembly was constructed utilizing single cells on the scaled-up module. According to the experiment results, the impedance was increased with increasing cells connected in series. On the contrary, the impedance was decreased with increasing cells connected in parallel.

Beschreibung: Sensors health monitoring is essentially important for reliable functioning of safety-critical chemical and nuclear power plants. Autoassociative neural network (AANN) based empirical sensor models have widely been reported for sensor calibration monitoring. However, such ill-posed data driven models may result in poor generalization and robustness. To address above-mentioned issues, several regularization heuristics such as training with jitter, weight decay, and cross-validation are suggested in literature. Apart from these regularization heuristics, traditional error gradient based supervised learning algorithms for multilayered AANN models are highly susceptible of being trapped in local optimum. In order to address poor regularization and robust learning issues, here, we propose a denoised autoassociative sensor model (DAASM) based on deep learning framework. Proposed DAASM model comprises multiple hidden layers which are pretrained greedily in an unsupervised fashion under denoising autoencoder architecture. In order to improve robustness, dropout heuristic and domain specific data corruption processes are exercised during unsupervised pretraining phase. The proposed sensor model is trained and tested on sensor data from a PWR type nuclear power plant. Accuracy, autosensitivity, spillover, and sequential probability ratio test (SPRT) based fault detectability metrics are used for performance assessment and comparison with extensively reported five-layer AANN model by Kramer.

Beschreibung: A combined cycle that combines AWM cycle with a nuclear closed Brayton cycle is proposed to recover the waste heat rejected from the precooler of a nuclear closed Brayton cycle in this paper. The detailed thermodynamic and economic analyses are carried out for the combined cycle. The effects of several important parameters, such as the absorber pressure, the turbine inlet pressure, the turbine inlet temperature, the ammonia mass fraction, and the ambient temperature, are investigated. The combined cycle performance is also optimized based on a multiobjective function. Compared with the closed Brayton cycle, the optimized power output and overall efficiency of the combined cycle are higher by 2.41% and 2.43%, respectively. The optimized LEC of the combined cycle is 0.73% lower than that of the closed Brayton cycle.

Beschreibung: This paper identifies the partial shading problem of a PV module using the one-diode model and simulating the characteristics exhibiting multiple-peak power output condition that is similar to a PV array. A modified particle swarm optimization (PSO) algorithm based on the suggested search-agent deployment, retracking condition, and multicore operation is proposed in order to continuously locate the global maximum power point for the PV system. Partial shading simulation results for up to 16 modules in series/parallel formats are presented. A distributed PV system consisting of up to 8 a-silicon thin film PV panels and also having a dedicated DC/DC buck converter on each of the modules is tested. The converter reaches its steady state voltage output in 10 ms. However for MPPT operation, voltage, and current measurement interval is set to 20 ms to avoid unnecessary noise from the entire electric circuit. Based on the simulation and experiment results, each core of the proposed PSO operation should control no more than 4 PV modules in order to have the maximum tracking accuracy and minimum overall tracking time. Tracking for the global maximum power point of a distributed PV system under various partial shading conditions can be done within 1.3 seconds.

Beschreibung: This paper discusses the utilisation of PV systems for electric vehicles charging for transportation requirements of smart cities. The gap between PV power output and vehicles charging demand is highly variable. Therefore, there is a need for additional support from a public distribution grid or a storage device in order to handle the residual power. Long term measurement data retrieved from a charging station for 15 vehicles equipped with a PV system were used in the research. Low and high irradiation seasons influenced the PV output. The charging demand of electric vehicles varied over the course of a year and was correlated to weather conditions. Therefore, the sizing and performance of a supportive storage device should be evaluated in a statistical manner using long period observations.

Beschreibung: The study of the void reactivity variation in innovative BWR fuel assemblies is presented in this paper. The innovative assemblies are loaded with high enrichment fresh UO2 and MOX fuels. UO2 fuel enrichment is increased above existing design limitations for LWR fuels (〉5%). MOX fuel enrichment with fissile Pu content is established to achieve the same burnup level as that of high enrichment UO2 fuel. For the numerical analysis, the TRITON functional module of SCALE 6.1 code with the 238-group ENDF/B-VI cross section data library was applied. The investigation of the void reactivity feedback is performed in the entire 0–100% void fraction range. Higher values of void reactivity coefficient for assembly loaded with MOX fuel are found in comparison with values for assembly loaded with UO2 fuel. Moreover, coefficient values for MOX fuel are positive over 75% void fraction. The variation of the void reactivity coefficient is explained by the results of the decomposition analysis based on four-factor formula and neutron absorption reactions for main isotopes. Additionally, the impact of the moderation enhancement on the void reactivity coefficient was investigated for the innovative assembly with MOX fuel.

Beschreibung: In Canada, safe operation of CANDU (CANada Deuterium Uranium; it is a registered trademark of Atomic Energy of Canada Limited) reactors is supported by a full-scope program of nuclear safety research and development (R&D) in key technical areas. Key nuclear R&D programs, facilities, and expertise are maintained in order to address the unique features of the CANDU as well as generic technology areas common to CANDU and LWR (light water reactor). This paper presents an overview of the CANDU safety R&D which includes background, drivers, current status, challenges, and future directions. This overview of the Canadian nuclear safety R&D programs includes those currently conducted by the COG (CANDU Owners Group), AECL (Atomic Energy of Canada Limited), Candu Energy Inc., and the CNSC (Canadian Nuclear Safety Commission) and by universities via UNENE (University Network of Excellence in Nuclear Engineering) sponsorship. In particular, the nuclear safety R&D program related to the emerging CANDU ageing issues is discussed. The paper concludes by identifying directions for the future nuclear safety R&D.

Beschreibung: Hexagonal wurtzite pure ZnO and BiOBr-ZnO composites were synthesized by facile hydrothermal method. The amount of BiOBr as dopant was adjusted from 5 wt.% to 75 wt.%, and correspondingly the morphologies and crystal structures of the as-prepared composites were measured and discussed. Specifically, according to XRD patterns and SEM images, the main crystalline structure of ZnO was not destroyed after doping, but growth of ZnO crystals was inhibited by doping BiOBr. Meanwhile, the optical properties of the composites were measured by the diffuse reflectance spectra (DRS). The band gap of composites was also calculated using the classical Tauc equation and it was found to be around 3.0 eV. In the test of photocatalytic activation, the ZnO-BiOBr photocatalysts exhibited high photocatalytic efficiencies in the degradation of Rhodamine B (RhB) under visible-light irradiation. It was ascribed to not only the small size of crystalline, but also the reduction in the recombination rate of the photogenerated carriers for the enhancement effect of p-n heterojunction. This work sheds light on improving the photocatalytic performance by establishing the heterojunction and contributes to the development of a commercially competitive photocatalyst.

Beschreibung: When a concrete structure is subjected to an impact, the material is subjected to high triaxial compressive stresses. Furthermore, the water saturation ratio in massive concrete structures may reach nearly 100% at the core, whereas the material dries quickly on the skin. The impact response of a massive concrete wall may thus depend on the state of water saturation in the material. This paper presents some triaxial tests performed at a maximum confining pressure of 600 MPa on concrete representative of a nuclear power plant containment building. Experimental results show the concrete constitutive behavior and its dependence on the water saturation ratio. It is observed that as the degree of saturation increases, a decrease in the volumetric strains as well as in the shear strength is observed. The coupled PRM constitutive model does not accurately reproduce the response of concrete specimens observed during the test. The differences between experimental and numerical results can be explained by both the influence of the saturation state of concrete and the effect of deviatoric stresses, which are not accurately taken into account. The PRM model was modified in order to improve the numerical prediction of concrete behavior under high stresses at various saturation states.

Beschreibung: The photocatalytic degradation of indigo carmine (IC) dye in the presence of titanium dioxide under different conditions was reported. Several factors which interfere with the photodegradation efficiency as catalyst concentration, pH, initial concentration of dye, presence of inorganic anions, temperature, and the addition of hydrogen peroxide were studied under artificial irradiation with a 125 W mercury vapor lamp. Additionally, the catalyst supported on glass spheres was used for the photocatalytic degradation of the dye present in several types of waters in a CPC solar pilot plant. The photocatalytic products, carboxylic acids, and and were followed during IC mineralization. Formate, acetate, and oxalate were detected in real MWWTP secondary effluent. The mineralization efficiency was of 42 and 21% using in suspension and supported TiO2, respectively. In order to evaluate biological effects, Eisenia andrei earthworms were used as a model organism. No significant difference () of weight was observed in the earthworm submitted to different concentrations of IC and its photoproducts. The photocatalytic degradation of IC on TiO2 supported on glass spheres suffered strong influence of the water matrix; nevertheless the method has the enormous advantage that it eliminates the need for the final catalyst removal step, reducing therefore the cost of treatment.

Beschreibung: This paper proposes an integrated photovoltaic (PV) and proton exchange membrane fuel cell (PEMFC) system for continuous energy harvesting under various operating conditions for use with a brushless DC motor. The proposed scheme is based on the incremental conductance (IncCond) algorithm combined with the sliding mode technique. Under changing atmospheric conditions, the energy conversion efficiency of a PV array is very low, leading to significant power losses. Consequently, increasing efficiency by means of maximum power point tracking (MPPT) is particularly important. To manage such a hybrid system, control strategies need to be established to achieve the aim of the distributed system. Firstly, a Matlab/Simulink based model of the PV and PEMFC is developed and validated, as well as the incremental conductance sliding (ICS) MPPT technique; then, different MPPT algorithms are employed to control the PV array under nonuniform temperature and insolation conditions, to study these algorithms effectiveness under various operating conditions. Conventional techniques are easy to implement but produce oscillations at MPP. Compared to these techniques, the proposed technique is more efficient; it produces less oscillation at MPP in the steady state and provides more precise tracking.

Beschreibung: In photocatalysis, the recombination of electron-hole pairs is generally regarded as one of its most serious drawbacks. The synthesis of various composites with heterojunction structures has increasingly shed light on preventing this recombination. In this work, a BiOBr-Bi2WO6 photocatalytic heterojunction semiconductor was synthesized by the facile hydrothermal method and applied in the photocatalytic degradation process. It was determined that both reaction time and temperature significantly affected the crystal structure and morphologies of the photocatalysts. BiOBr (50 at%)-Bi2WO6 composites were prepared under optimum synthesis conditions (120°C for 6 h) and by theoretically analyzing the DRS results, it was determined that they possessed the suitable band gap (2.61 eV) to be stimulated by visible-light irradiation. The photocatalytic activities of the as-prepared photocatalysts were evaluated by the degradation of Rhodamine B (RhB) under visible-light irradiation. The experimental conditions, including initial concentration, pH, and catalyst dosage, were explored and the photocatalysts in this system were proven stable enough to be reused for several runs. Moreover, the interpreted mechanism of the heterojunction enhancement effect proved that the synthesis of a heterojunction structure provided an effective method to decrease the recombination rate of the electron-hole pairs, thereby improving the photocatalytic activity.

Beschreibung: The performance of a solar assisted heat pump dryer integrated with biomass furnace has been designed and evaluated for drying red chillies, and drying kinetics of red chillies were evaluated. The red chillies were dried from 22 kg with moisture content of 4.26 db to moisture content of 0.08 db which needed 11 hours, with the average drying chamber temperature, drying chamber relative humidity, and an air mass flow rate of 70.5°C, 10.1%, and 0.124 kg/s, respectively, while the open sun drying needed 62 hours. Compared to open sun drying, this dryer yielded 82% saving in drying time. The drying rate, the specific moisture extraction rate, and thermal efficiency of the dryer were estimated in average to be about 1.57 kg/h, 0.14 kg/kWh, and 9.03%, respectively. Three mathematical models, the Newton, Henderson-Pabis, and Page models, were fitted to the experimental data on red chillies dried by solar assisted heat pump dryer integrated with biomass furnace and open sun drying. The performance of these models was evaluated by comparing the coefficient of determination (), mean bias error (MBE), and root mean-square error (RMSE). The Page model gave the best results for representing drying kinetics of red chillies.

Beschreibung: A novel modeling tool for calculation of central receiver concentrated flux distributions is presented, which takes into account drift effects. This tool is based on a drift model that includes different geometrical error sources in a rigorous manner and on a simple analytic approximation for the individual flux distribution of a heliostat. The model is applied to a group of heliostats of a real field to obtain the resulting flux distribution and its variation along the day. The distributions differ strongly from those obtained assuming the ideal case without drift or a case with a Gaussian tracking error function. The time evolution of peak flux is also calculated to demonstrate the capabilities of the model. The evolution of this parameter also shows strong differences in comparison to the case without drift.

Beschreibung: In sodium-cooled fast reactors (SFR), grid plate is a critical component which is made of 316 L(N) SS. It is supported on core support structure. The grid plate supports the core subassemblies and maintains their verticality. Most of the components of SFR are made of 316 L(N)/304 L(N) SS and they are in contact with the liquid-metal sodium which acts as a coolant. The peak operating temperature in SFR is 550°C. However, the self-welding starts at 500°C. To avoid self-welding and galling, hardfacing of the grid plate has become necessary. Nickel based cobalt-free colmonoy 5 has been identified as the hardfacing material due to its lower dose rate by Plasma Transferred Arc Welding (PTAW). This paper is concerned with the measurement and investigations of the effects of the residual stress generated due to thermal cycling on a scale-down physical model of the grid plate. Finite element analysis of the hardfaced grid plate model is performed for obtaining residual stresses using elastoplastic analysis and hence the results are validated. The effects of the residual stresses due to thermal cycling on the hardfaced grid plate model are studied.

Beschreibung: The purpose of this study was to evaluate the photostability of inclusion complexes of the histamine antagonist loratadine (LORA) with -, -, and -cyclodextrins (CDs). Accordingly, binary drug-CD complexes were prepared using the coevaporation method at 1 : 1, 1 : 2, and 1 : 3 stoichiometric ratios, which were characterized by thermal analysis. Subsequently, solutions of the complexes at 500 μg mL−1 in HCl 0.1 M were subjected to irradiation in a photostability chamber for 12 hours, and the content of the remaining active ingredient was quantified by means of high-performance liquid chromatography. It is possible to observe the presence of two products originating from photodegradation (P1 and P2), which were identified in solutions of loratadine with - and -CD. By means of statistical analysis, we conclude that the drug:-CD and drug:-CD (1 : 1) complexes proved to be more efficient in the photostability assay, obtaining a nonsignificant level of degradation and full recovery of LORA.

Beschreibung: As for Light Water Reactors (LWRs), one of the most challenging accidents for the future DEMOnstration power plant is the Loss of Coolant Accident, which can trigger the pressurization of the confinement structures and components. Hence, careful analyses have to be executed to demonstrate that the confinement barriers are able to withstand the pressure peak within design limits and the residual cooling capabilities of the Primary Heat Transfer System are sufficient to remove the decay heat. To do so, severe accident codes, as MELCOR, can be employed. In detail, the MELCOR code has been developed to cope also with fusion reactors, but unfortunately, these fusion versions are based on the old 1.8.x source code. On the contrary, for LWRs, the newest 2.1.x versions are continuously updated. Thanks to the new features introduced in these latest 2.1.x versions, the main phenomena occurring in the helium-cooled blanket concepts of DEMO can be simulated in a basic manner. For this purpose, several analyses during normal and accidental DEMO conditions have been executed. The aim of these analyses is to compare the results obtained with MELCOR 1.8.2 and MELCOR 2.1 in order to highlight the differences among the results of the main thermal-hydraulic parameters.

Beschreibung: Design, construction, and evaluation of a cylindrical-trough solar concentrator with 1.3 m aperture, 2.15 m length, and 0.54 m focal length, with heat-pipe or vacuum tube receiver and one axis tracking system, are presented. Design performance was tested under ASHRAE standard 93-1986 (RA 91). The concentrator system is lightweight and inexpensive since it was made of polymeric membranes and was pneumatically inflated to acquire its cylindrical shape achieving good optical quality. Further implementation of a flat and a cylindrical extension of the concentrating mirror as secondary mirrors was incorporated into the concentrator design in order to compensate for seasonal variations of collected radiation. Total initial investment of $163.30 or $58.5/m2 and efficiencies ranging from 33 to 25% for 25 up to 65°C show an excellent cost-performance ratio. Construction, costs, and efficiencies obtained by us and developed by other groups are compared to emphasize the high cost/benefit ratio and efficiencies of this approach.

Beschreibung: An optimized fabrication of bulk-heterojunction solar cells (BHJ SCs) based on previously reported diketopyrrolopyrrole donor, ethyl-hexylated DPP(TBFu)2, as well as two new DPP(TBFu)2 derivatives with ethyl-hexyl acetate and diethyl acetal solubilizing side-chains and PC60BM as an acceptor is demonstrated. Slow gradual annealing of the solar cell causing the effective donor-acceptor reorganization, and as a result higher power conversion efficiency (PCE), is described. By replacing a hole transporting layer PEDOT:PSS with MoO3 we obtained higher PCE values as well as higher thermal stability of the anode contact interface. DPP(TBFu)2 derivative containing ethyl-hexyl acetate solubilizing side-chains possessed the best as-cast self-assembly and high crystallinity. However, the presence of ethyl-hexyl acetate and diethyl acetal electrophilic side-chains stabilizes HOMO energy of isolated DPP(TBFu)2 donors with respect to the ethyl-hexylated one, according to cyclic voltammetry.

Beschreibung: The biggest problems of our time are environmental pollution and the reduction of fossil fuel resources. In recent years, photovoltaic (PV) has started to be used efficiently in order to produce electrical energy from solar energy throughout the world. In this study, a wheat mover machine taking its energy with PV technology transformation from the sun was designed supported by smart sensors. The designed vehicle was tested in two wheat fields in Sivas in Turkey. It was seen that daily average sunshine rates were not lower than 700 Watt/m2 during the testing dates and time. The amounts of electrical charge used to mow 5 m2 and 50 m2 areas are obtained as 500 mAh and 3395 mAh, respectively. Also maximum power is calculated from used PV panel as 26.15 Watt during the day of the experiments. The range of solar radiation intensity is found 4.5 kWh/m2/day at the studied kWh which was 0.140 USD on the date of November 2015. This system is 94.5% more economic than conventional mowers over an area of 1000 m2.

Beschreibung: The mean cost price of electricity in Burkina Faso at the end of the last quarter of 2012 was 158 FCFA/kWh for a country where more than 46% of the population lives below the national poverty threshold. To look for solution to that problem, the resort to photovoltaic solar energy is justified for that country. The purpose of this study is to promote the integration of both technical and economical surveys in solar energy preliminary projects in Ouagadougou. To reach that, investigations were carried out in some households and attention was paid from the calibration of the domestic electric meters. Energy demands collected within each household allow us to design a corresponding solar kit through optimization rules. An estimate was edited and financial viability study for each household was also carried out thereafter. In this study, only households using the national electricity network calibration meter on their disadvantage favorably answered to all financial indicators and appear as the only one that could profit from such project. This work is helpful to note that photovoltaic solar energy still stays at a primitive level of competitiveness compared to conventional energy resources for small systems in Ouagadougou.

Beschreibung: Multiwall carbon nanotubes (MWCNTs) were modified by acids (H2SO4 : HNO3) for generating active groups on the nanotube surface. Unmodified- and modified-carbon nanotubes were coated on the conductive glass and conductive plastic substrates by a slurry paste method, and they were used as the counter electrodes (CEs) of dye-sensitized solar cells (DSSCs). Scanning electron microscopy reveals that carbon nanotubes are evenly deposited on the conductive glass. The efficiency of the glass based DSSCs of unmodified- and modified-carbon nanotubes and Pt CEs is ~4.73%, ~5.66%, and ~6.08%, respectively. The efficiency of the plastic based DSSCs of the unmodified- and modified-carbon nanotubes CEs is ~0.80% and ~2.11%, respectively. The voltammogram and electrochemical impedance spectroscopy results suggest that the superior performance of the modified-carbon nanotubes DSSCs is attributable to the high electrocatalytic activity and the low charge-transfer resistance of the modified-carbon nanotubes film over the unmodified-carbon nanotubes film.

Beschreibung: Diesel engine is presently facing the challenge of controlling NOx and soot emissions on transient cycles, to meet stricter emission norms and to control emissions during field operations. Development of a simulation tool for NOx and soot emissions prediction on transient operating cycles has become the most important objective, which can significantly reduce the experimentation time and cost required for tuning these emissions. Hence, in this work, a 0D comprehensive predictive model has been formulated with selection and coupling of appropriate combustion and emissions models to engine cycle models. Selected combustion and emissions models are further modified to improve their prediction accuracy in the full operating zone. Responses of the combustion and emissions models have been validated for load and “start of injection” changes. Model predicted transient fuel consumption, air handling system parameters, and NOx and soot emissions are in good agreement with measured data on a turbocharged high power density common rail engine for the “nonroad transient cycle” (NRTC). It can be concluded that 0D models can be used for prediction of transient emissions on modern engines. How the formulated approach can also be extended to transient emissions prediction for other applications and fuels is also discussed.

Beschreibung: This experimental part investigates the effect of injection timing on performance and emissions of homogenous mixture compressed natural-gas direct injection. The engine of 1.6 L capacity, 4 cylinders, spark ignition, and compression ratio of 14 was used. Performance and emission were recorded under wide-open throttle using an engine control system (Rotronics) and the portable exhaust gas analyser (Kane). The engine was tested at speed ranging from 1500 revolutions per minute (RPM) to 4000 RPM with 500 RPM increments. The engine control unit (ECU) was modified using Motec 800. The injection timings investigated were at the end of injection (EOI) 120 bTDC, 180 bTDC, 300 bTDC, and 360 bTDC. Results show high brake power, torque, and BMEP with 120 as compared with the other injection timings. At 4000 RPM the power, torque, and BMEP with 120 were 5% compared to that with 180. Furthermore, it shows low BSFC and high fuel conversion efficiency with 120. With 360, the engine produced less CO and CO2 at higher speeds.

Beschreibung: The pyrolysis/devolatilization is a basic step of thermochemical processes and requires fundamental characterization. In this paper, the kinetic model of pyrolysis is specified as a one-step global reaction. This type of reaction is used to describe the thermal degradation of wheat straw samples by measuring rates of mass loss of solid matter at a linear increase in temperature. The mentioned experiments were carried out using a derivatograph in an open-air environment. The influence of different factors was investigated, such as particle size, humidity levels, and the heating rate in the kinetics of devolatilization. As the measured values of mass loss and temperature functions transform in Arrhenius coordinates, the results are shown in the form of saddle curves. Such characteristics cannot be approximated with one equation in the form of Arrhenius law. For use in numerical applications, transformed functions can be approximated by linear regression for three separate intervals. Analysis of measurement resulting in granulation and moisture content variations shows that these factors have no significant influence. Tests of heating rate variations confirm the significance of this impact, especially in warmer regions. The influence of this factor should be more precisely investigated as a general variable, which should be the topic of further experiments.

Beschreibung: In this work, we studied the effect of TiO2 sensitization with dry biomass extracted of cyanobacteria on the degradation of methylene blue dye (AM). Cyanobacterial cultures isolated from water samples were collected from the swamp of Malambo in Colombia; two main genera of cyanobacteria were identified, and they were cultivated with BG-11 culture medium. The concentrations of chlorophyll a in the exponential and stationary phases of growth were measured; the phycobilin content was quantified by spectrophotometry. Thin films of TiO2 were deposited by a doctor blade method, and they were sensitized by wet impregnation. Furthermore, a methylene blue (MB) photodegradation process was studied under visible light irradiation on the cyanobacterial biomass sensitized TiO2 material (TiO2/sensitizer); besides, the pseudo-first-order model was used to obtain kinetic information about photocatalytic degradation. The results showed that the BG-11+ treatment reported a higher amount of dry biomass and phycobiliproteins. After the sensitization process, the TiO2/sensitizer thin films showed a significant red shift in the optical activity; besides the thin film roughness decreasing, the TiO2/sensitizer showed photocatalytic activity of 23.2% under visible irradiation, and besides, the kinetic () constant for TiO2/sensitizer thin films was 3.1 times greater than the value of TiO2 thin films. Finally, results indicated that cyanobacterial biomass is a suitable source of natural sensitizers to be used in semiconductor sensitization.

Beschreibung: Constant exposure of a photovoltaic (PV) panel to sunlight causes it to overheat and, consequently, its rated efficiency decreases leading to a drop in its generated power. In this study, a PV panel was tested under standard test conditions in a halogen lamp solar simulator at different solar irradiance values. The PV panel was then fitted with heat dissipating fins and measured under identical test parameters; thereafter, repurposed materials such as high-density polyethylene (HDPE) and plastic bags were, separately, added to the PV panel with fitted heat-extraction fins and the performance was evaluated again. Passively cooling the PV panel with fins and repurposed materials resulted in a 22.7% drop in the PV panel’s temperature, while an 11.6% increase in power output occurred at 1000 W m-2. Utilizing repurposed waste materials in PV cooling improves a panel’s efficiency and saves the environment from the ecological effects of dumping these materials.

Beschreibung: Double modifications of TiO2 by doping with WO3 and by dispersing on a SiO2 support were made by the one-pot sol-gel method. Doping with W shifts the TiO2 band gap energy from 3.2 eV to around 3.06 eV. The surface area of the supported W-TiO2/SiO2 material was significantly increased, by approximately 3 times, in comparison to the bare TiO2. The photocatalytic activities of the catalysts were evaluated in the degradation reaction of p-nitrophenol in aqueous solution and basic medium. After 240 min of photodegradation, more than approximately 99% p-nitrophenol could be mineralized with the most active W-TiO2/SiO2 catalyst. Under UV irradiation, p-nitrophenol was initially photodegraded into hydroquinone and benzosemiquinone intermediates, which were further degraded into smaller fragments such as organic carboxylic acids and finally completely mineralized. A proposed photoreaction mechanism was presented based on the key roles of the surface hydroxyl species and superoxide radicals such as O2- and ⋅OH, together with W6+/W5+ couples and e-/h+ pairs in the catalysts in the p-nitrophenol photodegradation. The one-pot sol-gel synthesis method was proven to be effective to obtain W-TiO2/SiO2 catalyst with large surface area and high photocatalytic activity, and it can be also used for the preparation of other heterogeneous catalysts.

Beschreibung: A modified multiobjective self-adaptive differential evolution algorithm (MMOSADE) is presented in this paper to improve the accuracy of multiobjective optimization design in the nuclear power system. The performance of the MMOSADE is tested by the ZDT test function set and compared with classical evolutionary algorithms. The results indicate that MMOSADE has a better performance in convergence and diversity. Based on the MMOSADE, a multiobjective optimization design platform for the nuclear power system is proposed, and the application of which is carried out. The evaluation program of the PRHR-HX in AP1000 is developed, and its reliability is verified. The optimal design schemes of PHHR-HX are obtained by utilizing the multiobjective optimization design platform. The results show that the optimal design schemes can envelop the prototype design scheme. This conclusion proves that the optimization design platform proposed in this paper is effective and feasible.

Beschreibung: COMSOL Multiphysics has been used to conduct thermal-hydraulic analysis in multiple nuclear applications. The aim of this study is to benchmark the prediction accuracy of COMSOL Multiphysics in performing thermal-hydraulic analysis of TRIGA (Training, Research, Isotopes, General Atomics) reactors such as the Geological Survey TRIGA Reactor (GSTR) by comparing its predictions with RELAP5 (a widely used code in nuclear thermal-hydraulic analysis) results and experimental data. The GSTR type is Mark I with a full thermal power of 1 MW, and it resides at the Denver Federal Center (DFC) in Colorado. The numerical investigation of the present work is carried out by developing single-subchannel thermal-hydraulic models of the GSTR utilizing RELAP5 and COMSOL codes. The models estimate the temperatures (fuel, outer clad, and coolant) and water flow patterns in the core as well as fuel element powers at which void starts to form within the coolant subchannels. Then, these models’ predictions are quantitatively evaluated and compared with the measured data.

Beschreibung: A practical scale mechanical decladder that can slit spent nuclear fuel rod-cuts (hulls + pellets) of several tens of kg HM/batch is being developed to supply UO2 pellets to a voloxidation process. The mechanical decladder is an apparatus for separating and recovering fuel material and cladding tubes by horizontally slitting the cladding tube of a fuel rod and a defective irradiated fuel rod. In this study, we address the engineering design of the mechanical decladder for the pretesting of rod-cut slitting. To obtain the requirements of the mechanical decladder, we first manufactured a slitter for testing based on the decladding and shearing conditions of hulls and pellets. The performance test of the testing device for decladding was carried out using a 2-CUT blade module and a 3-CUT blade module. We evaluated the decladding methods for the mechanical decladder and selected the 3-CUT blade module based on the results. A buckling measurement instrument was used to perform a buckling verification test according to the length of a rod-cut and to determine decladder dimensions. The optimum decladding rod-cut length for buckling prevention was calculated. Furthermore, we analyzed the decladding mechanism for various slitting methods. Design/fabrication and preliminary tests of the practical scale mechanical decladder were also performed. For this purpose, we constructed the main mechanism by utilizing the SolidWorks modeling and analysis program and fabricated a new mechanical decladder. Based on the derived requirements, a mechanical decladder with three main modules was designed and fabricated for testing. Simulated rod-cuts of zircaloy were also manufactured to test the basic performance of the decladder, and a data acquisition system was constructed using RSC 232 to measure decladding force and velocity. In the basic test, the rod-cut was completely sectioned into three evenly spaced locations by the new mechanical decladder.

Beschreibung: This paper extends a recent theoretical study that was previously presented in the form of a brief communication (Zimont, C&F, 192, 2018, 221-223), in which we proposed a simple splitting method for the derivation of two-fluid conditionally averaged equations of turbulent premixed combustion in the flamelet regime, formulated more conveniently for applications involving unclosed equations without surface-averaged unknowns. This two-fluid conditional averaging paradigm avoids the challenge in the Favre averaging paradigm of modeling the countergradient scalar transport phenomenon and the unusually large velocity fluctuations in a turbulent premixed flame. It is a more suitable conceptual framework that is likely to be more convenient in the long run than the traditional Favre averaging method. In this article, we further develop this paradigm and pay particular attention to the problem of modeling turbulent premixed combustion in the context of a two-fluid approach. We formulate and analyze the unclosed differential equations in terms of the conditions of the Reynolds stresses , and the mean chemical source , which are the only modeling unknowns required in our alternative conditionally averaged equations. These equations are necessary for the development of model differential equations for the Reynolds stresses and the chemical source in the advanced modeling and simulation of turbulent premixed combustion. We propose a simpler approach to modeling the conditional Reynolds stresses based on the use of the two-fluid conditional equations of the standard “” turbulence model, which we formulate using the splitting method. The main problem arising here is the appearance in these equations of unknown terms describing the exchange of the turbulent energy and dissipation rate in the unburned and burned gases. We propose an approximate way to avoid this problem. We formulate a simple algebraic expression for the mean chemical source that follows from our previous theoretical analysis of the transient turbulent premixed flame in the intermediate asymptotic stage, in which small-scale wrinkles in the instantaneous flame surface reach statistical equilibrium, while the large-scale wrinkles remain in statistical nonequilibrium.

Beschreibung: After the successful construction and operation experience of the 10 MW high-temperature gas-cooled reactor (HTR-10), a high-temperature gas-cooled pebble-bed modular (HTR-PM) demonstration plant is under construction in Shidao Bay, Rongcheng City, Shandong province, China. An online gross monitoring instrument has been designed and placed at the exit of the helium purification system (HPS) of HTR-PM and is used to detect the activity concentration in the primary circuit after purification. The source terms in the primary loop of HTR-PM and the helium purification process were described. The detailed configuration of the gross monitoring instrument was presented in detail. The Monte Carlo method was used to simulate the detection efficiency of the monitoring system. Since the actual source terms in the primary loop of HTR-PM may be different than the current design values, a sensitivity analysis of the detection efficiency was implemented based on different relative proportions of the nuclides. The accuracy and resolution of the NaI(Tl) detector were discussed as well.

Beschreibung: In this study, an exergy analysis of two kinds of solar-driven cogeneration systems consisting of solar collectors and an organic Rankine cycle (ORC) is presented for series mode and parallel mode. Three kinds of solar collectors are considered: flat-plate collectors (FPC), evacuated tube collectors (ETC), and parabolic trough collectors (PTC). This study mainly compares the exergy output of the two kinds of solar cogeneration systems under different temperatures of the return heating water and different inlet temperatures of the solar collectors. This study shows that, from the perspective of or , the parallel mode is superior to the series mode. From the perspective of , the parallel mode is superior to the series mode when the solar collector is FPC; however, the series mode is superior to the parallel mode when the solar collector is PTC. When the solar collector is ETC, the result depends on the temperature of the return heating water. When the temperature of the return heating water is low (below 46°C), the series mode is better, and when the temperature of the return heating water is high (above 46°C), the parallel mode is better.

Beschreibung: The assessment of hydrogen release, distribution, and mitigation measures in the containment of a nuclear power plant is increasingly based on code calculations. These calculations require state-of-the-art experiments to benchmark the codes against them. Two of these experiments are presented in this paper. These experiments were conducted in the PANDA facility (Switzerland) in the framework of the OECD/NEA HYMERES project. The experiments consider natural circulation flow in a two-room type containment where flow loops can form between the inner and the outer zones. During normal operation these zones are separated and in the case of an accident they become either connected by the opening of rupture disks, convective foils, and dampers or connected by bursting of doors and opening of other connections between compartments. For the experiments considered here one lower PANDA-vessel represents the steam generator (SG) tower and the inaccessible area whereas the other vessel represents the outer room area. The lower vessels are isolated from one another except for a small aperture that represents the damper. The two upper vessels—representing the containment dome—are connected to the lower vessels through tubes. The scenario consisted of four phases. In phase 1, a high steam mass flow rate was injected in the vessel representing the SG tower. After the relaxation phase 2, helium (representing hydrogen) was injected in the same vessel (phase 3). Finally in phase 4 no active interventions were done until the end of the test. Two tests were conducted to evaluate the developing helium transport by the natural circulation flow: one with and one without damper (by closing the aperture). The results showed that a two-room containment (TRC) mixing scenario can be well represented with the PANDA facility. It is found that, with the mixing damper open, a global natural circulation loop develops over all four vessels, whereas with closed damper the natural circulation loop is established only between the three vessels representing the inner zone and the upper dome. It is shown that the presence of the damper has a strong effect on the resulting helium content in the inner zone with 3 times less helium at the end of the test compared with the configuration without damper. The formation of a stable helium stratification in the upper vessels was observed in the presence of the open damper.

Beschreibung: This work focuses on the impact of the devolatilization and char combustion mode modelling on the structure of a large-scale, biomass and coal co-fired flame using large eddy simulations. The coal modelling framework previously developed for the simulation of combustion in large-scale facilities is extended for biomass capabilities. An iterative procedure is used to obtain devolatilization kinetics of coal and biomass for the test-case specific fuels and heating conditions. This is achieved by calibrating the model constants of two empirical models: the single first-order model and the distributed activation energy model. The reference data for calibration are devolatilization yields obtained with predictive coal and biomass multistep kinetic mechanisms. The variation of both particle density and diameter during char combustion is governed by the conversion mode, which is modelled using two approaches: the power law using a constant parameter that assumes a constant mode during char combustion and a constant-free model that considers a variable mode during combustion. Three numerical cases are considered: single first-order reaction with constant char combustion mode, distributed activation energy with constant char combustion mode, and single first-order reaction with variable char combustion mode. The numerical predictions from the large eddy simulations are compared with experimental results of a high co-firing rate large-scale laboratory flame of coal and biomass. Furthermore, results from single particle conversion under idealised conditions, isolating the effects of turbulence, are presented to assist the interpretation of the predictions obtained with large eddy simulations. The effects of the devolatilization and conversion mode modelling on the flame lift-off, flame length, and spatial distribution and radial profiles of O2 and CO2 are presented and discussed. Both the devolatilization and conversion mode modelling have a significant effect on the conversion of particles under idealised conditions. The large eddy simulations results show that the devolatilization model has a strong impact on the flame structure, but not on the flame lift-off. On the other hand, for the tested numerical conditions, the char combustion mode model has a marginal impact on the predicted results.

Beschreibung: The LOCA (loss of coolant accident) is a kind of severe accident in the operation of PHWR (pressurized heavy water reactor) as well as other nuclear facilities, and possible cause of LOCA can be counted on the ballooning of pressure tube (PT) contacted to the outer calandria tube (CT) in the moderator system of CANDU-6 reactors. In the paper, we simulated the 150-kW experimental facility proposed by IAEA/ISCP, modeling the transient creeping behavior of pressurized tube heated with thermal radiation between the gaps of two concentric pipes. The outer boundary is simplified with a switched model that depends on the local temperature. With a multiphysical model supported by a commercial code, COMSOL multiphysics, the unsteady phenomena are simulated with models concerning various kinds of mechanics such as thermodynamics, nonlinear structural dynamics, and two-phase boiling heat transfer models.

Beschreibung: BWRs are thus far the simplest energy systems to transform fission energy into electrical power. However, there are still many aspects in their operation that, under certain conditions, may induce BWR unstable behavior. The default indicator to study BWR unstable behavior is the Decay Ratio (DR). However, due to the fact that BWRs show very complex responses under instability and responses that may even be chaotic, the DR might not be a suitable choice to rely on to accommodate for such intricate behavior. In this work a novel methodology based on the Sample entropy (SampEn) and the noise-assisted multivariate empirical mode decomposition (NA-MEMD) is introduced. Such methodology was developed thinking for a real time-implementation of a stability monitor. The proposed methodology was tested with a set of signals that stem from several nuclear power plants in operation today that have experienced in the past unstable events, each one of a different nature.

Beschreibung: CIPS is a shift in the axial power towards the bottom half of the core, also known as axial offset anomaly (AOA), which results from the deposited of corrosion products during an operation. The main reason of CIPS is the solute particles especially boron compounds concentrated inside the porous deposit. The impact of CIPS is that the axial power distribution control may be more difficult and the shutdown margin can be decreased simultaneously. Besides, it also requires estimated critical condition (ECC) calculations to account for the effects of AOA. In this article, thermal-hydraulic subchannel code and boron deposit model have been combined to analyze the CIPS risk. The neutronics codes deal with the generation of homogenized neutron cross section as well as the calculation of local power factor. A simple rod assembly is analyzed with this combined method and simulation results are presented. Simulation results provide the boron hideout amount inside crud deposits and power shapes. The obtained results clearly show the power shape suppression in regions where crud deposits exist, which is a clear indication of CIPS phenomenon. And the CIPS effects on CHF have also been investigated. Result shows a margin of DNBR decrease in the crud case.

Beschreibung: Vigorously developing nuclear power is the main development direction of current renewable energy. In the nuclear environment, in order to avoid nuclear radiation damage to maintenance personnel and improve the efficiency of nuclear reaction, it is necessary and urgent to realize automatic replacement of vulnerable parts in the electron gun. As the key equipment for the generation and control of nuclear reactions in nuclear reactors, electron guns have been widely used in nuclear power plants of traveling wave reactors. However, the “high-voltage conductive ring” in electron guns is a vulnerable part. It is likely to cause nuclear reactor accidents when the vulnerable part is damaged. Automatic replacement of vulnerable parts is an important part of the entire maintenance equipment. Considering the entire maintenance equipment and the working environment, an innovative design process for vulnerable parts replacement is established. Under the guidance of the process, in order to ensure the continuity of a series of maintenance actions, the technical contradiction resolution theory is first used to conduct the overall analysis of the general direction to obtain the design layout. Then, the contradiction resolution theory and the object-field model analysis are utilized to get and improve the detailed design of the device mechanism. The theory of TRIZ can help us to get the overall mechanical structure design that meets the engineering requirements. The device is designed with a replacement part adjustment scheme to ensure the completion of the maintenance actions. Furthermore, the design provides a solution to the possible jamming phenomenon in the automatic maintenance process and achieves the maximum use efficiency of the storage and replacement of vulnerable parts.

Beschreibung: This study was carried out to examine the potential of antimony tri-iodide (SbI3) as a material for radiation detectors that operate at room temperature. SbI3 is a compound semiconductor with an AsI3-type crystal structure, high atomic number (Sb: 51, I: 53), high density (4.92 g/cm3), and a wide band-gap energy (2.2 eV). In addition, crystalline SbI3 is easy to grow by conventional crystal growth techniques from melting phase because the material exhibits a low melting point (171°C) and undergoes no phase transition in the range of its solid phase. In this study, SbI3 crystals were grown by the Bridgman method after synthesis of SbI3 from 99.9999% pure Sb and 99.999% pure I2. The grown crystals consisted of several large grains with red color and were confirmed to be single-phase crystals by X-ray diffraction analysis. SbI3 detectors with a simple planar structure were fabricated using the cleavage plates of the grown crystals, and the pulse-height spectra were recorded at room temperature using an 241Am alpha-particle (5.48 MeV) source. The detector showed response to the alpha-particle radiation.

Beschreibung: After the severe accident (SA) occurred at the Three-Miles Island Nuclear Power Plant (NPP), important efforts on the investigation of the different phenomena during this kind of accidents have been started. Several experimental campaigns investigating one phenomenon at time or the combination of two or more phenomena have been performed. Today, the Phébus experimental campaign is probably the most important activity on the evaluation of the coupling among different phenomena. Four out of five tests investigated the degradation of an intact Pressurized Water Reactor (PWR) fuel bundle and the subsequent transport of Fission Products (FP) and Structural Materials (SM) through the primary circuit and into the containment, while the fifth test was only the degradation of a bed of PWR fuel bundle debris. These tests were performed between 1990 and 2010 at the CEA Cadarache laboratories (France) in a 5000:1 scaled facility. The main four tests varied the employed control rod materials, the fuel burn-up, and the oxidizing conditions of the atmosphere (strongly or weakly). The outcomes of this experimental campaign created a solid base for the understanding of the involved phenomena and allowed the development of models and software codes capable of simulating the evolution of a SA in a real NPP. ASTEC and MELCOR were two of the main SA codes profiting from the results of this Phébus campaign. These two codes were further improved in the latest years to account for the findings obtained in more recent experimental campaigns. A continuous verification and validation work is then necessary to check how the newer code’s versions reproduce the tests performed in these older experimental campaigns such as Phébus one. The present work is intended to be the final step of a series of publications covering the activities carried out at University of Pisa with the ASTEC and the MELCOR SA codes on the four Phébus tests employing an intact PWR fuel bundle. Because of the complexity and the extent of these tests, only the containment aspects were considered in the precedent works, i.e., only the thermal-hydraulics transient and its coupling with the FP and SM behavior. Then, general conclusions based on the outcomes of these precedent works are summarized in this work.

Beschreibung: Pharmaceuticals are present in an aquatic environment usually in low (ng/L) concentrations. Their continuous release can lead to unwanted effects on the nontarget organisms. The main points of their collection and release into the environment are wastewater treatment plants. The wastewater treatment plants should be upgraded by new technologies, like advanced oxidation processes (AOPs), to be able to degrade these new pollutants. In this study, the degradation of albendazole (ALB), a drug against parasitic helminths, was investigated using four UV-based AOPs: UV photolysis, UV photocatalysis (over TiO2 film), UV + O3, and UV + H2O2. The ranking of the degradation process degree of the ALB and its degradation products for studied processes is as follows: UV photolysis 

Beschreibung: The energy scenario today is focused on the development and usage of solar cells, especially in the paradigm of clean energy. To readily create electron and hole pairs, solar cells utilize either photoactive or photosensitive components. A bulk heterojunction (BHJ) is a nanolayer consisting of donor and acceptor components with a large interpenetrated acceptor and donor contact area. In this context, a mix of P3HT and PCBM offers novelty for its use as an acceptor as well as a donor. In the work presented here, we address the mechanism of modelling and characterization of a BHJ-based polymer solar cell. Here, a new design of BHJ polymer solar cells have been designed, modelled, using Silvaco TCAD in the Organic Solar module, and matched with an already assembled device having similar features. Using this model, we have been able to estimate key parameters for the modelled devices, such as the short-circuit current density, open-circuit voltage, and fill factor with less than 0.25 error index compared to the fabricated counterpart, paving the way for fabless polymer solar cell design and optimization.

Beschreibung: This work undertakes both simulation and experimental studies of a new design of a photovoltaic thermal solar air collector (PV/T). In order to improve the thermal and electrical performances for a specific application, the analytical expressions for thermal parameters and efficiency are derived by developing an energy balance equation for each component of the PV/T air collector. This type of hybrid collector can be applied in the facades of buildings. The electricity and heat produced will satisfy the energy needs of the buildings, while ensuring an aesthetic view of its facades. A typical prototype was designed, constructed, and implemented in the applied research unit on renewable energies in Ghardaia, situated in the south of Algeria. This region has semiarid characteristics. Results obtained by an experimental test are presented and compared to those predicted through simulation. Results include the temperature of each component of the PV/T collector and air temperature at the inlet and outlet of the channel. It has been found that the theoretical results predicted by the developed mathematical model, for instance, outlet temperature, agree with those found through experimental work.

Beschreibung: Mismatching operating conditions negatively affect the extracted energy in photovoltaic (PV) systems. They may also lead to dangerous localized heating phenomena (hot spots) that can cause, in turn, accelerated ageing and reduced reliability. Since the adoption of bypass diodes or smart active switches does not prevent the occurrence of hotspots, it is necessary to investigate alternative strategies. A promising solution is represented by the proper regulation of the operating point of the PV cells in the current vs. voltage (-) or power vs. voltage (-) planes when mismatching conditions occur. In particular, in this paper, the existence of operating points allowing a suitable compromise between maximization of the extracted power and minimization of thermal stresses, due to hot spots, is experimentally evidenced. Experimental results highlighting the link existing between the operating point in the - plane and the PV cell temperature distribution under uniform and mismatching operating conditions are presented and discussed. On the basis of the obtained experimental results, it is possible to state that, when mismatching conditions occur, it is mandatory to properly choose the operating point: the global maximum power point may not be the best operating point. Hence, it is crucial to gain information about the eventual occurrence of mismatching conditions in order to be able to properly choose the best operating point. Therefore, another crucial aspect that is evidenced in this paper is represented by the fact that the detection of the occurrence of mismatching conditions, based on the analysis of the shape of the - and/or - characteristics, is effective only if the analysis is carried out for both positive and negative voltages.

Beschreibung: For sequentially collected data, this paper introduces a lag-one differencing method to estimate the random error standard deviation and then uses the estimate to calculate a change detection threshold in a moving window method to detect shifts in the short-term systematic error. Performance results on simulated and real data are presented. Fortunately, the impact of having to perform change detection on the estimated short-term systematic and random error variances is anticipated to be modest or small. The motivating example arises from facilities under nuclear safeguards agreements, where inspector data collected during International Atomic Energy Agency (IAEA) verifications are compared to corresponding operator data. The differences between the operator and inspector values are evaluated using an application of analysis of variance (ANOVA). Typically, it is assumed that short-term systematic errors change across inspection periods, so inspection periods form the groups used in the ANOVA. In some data sets, it appears that the short-term errors have changed at other times, so change detection methods could be used to detect the actual change times.

Beschreibung: Highly light scattering structures have been generated in a poly(ethylene terephthalate) (PET) film using a CO2 laser. The haze, and in some cases the transparency, of the PET films have been improved by varying the processing parameters of the laser (namely, scanning velocity, laser output power, and spacing between processed tracks). When compared with the unprocessed PET, the haze has improved from an average value of 3.26% to a peak of 55.42%, which equates to an absolute improvement of 52.16% or a 17-fold increase. In addition to the optical properties, the surfaces have been characterised using optical microscopy and mapped with an optical profilometer. Key surface parameters that equate to the amount and structure of surface roughness and features have been analysed. The CO2 laser generates microstructures at high speed, without affecting the bulk properties of the material, and is inherently a chemical-free process making it particularly applicable for use in industry, fitting well with the high-throughput, roll to roll processes associated with the production of flexible organic photovoltaic devices.

Beschreibung: The large and continuous use of fossil fuels as a primary energy source has led to several environmental problems, such as the increase of the greenhouse effect. In order to minimize these problems, attention has been drawn to renewable energy production. Solar energy is an attractive candidate as renewable source due to its abundance and availability. For this, it is necessary to develop devices able to absorb sunlight and convert it into fuels or electricity in a economical, technical and sustainable way. The so-called artificial photosynthesis has called the attention of researchers due to the possibility of using solar photocatalysts in converting water and CO2 into fuels. This manuscript presents a review of the recent developments of hybrid systems based on molecular photocatalysts immobilized on semiconductor surfaces for solar fuel production through water oxidation and CO2 reduction and also discusses the current challenges for the potential application of these photocatalyst systems.

Beschreibung: This study is aimed at providing a comparison between fuzzy systems and convectional P&O for tracking MPP of a PV system. MATLAB/Simulink is used to investigate the response of both algorithms. Several weather conditions are simulated: (i) uniform irradiation, (ii) sudden changing, and (iii) partial shading. Under partial shading on a PV panel, multipeaks appeared in - characteristics of the panel. Simulation results showed that a fuzzy controller effectively finds MPP for all weather condition scenarios. Furthermore, simulation results obtained from the FLC are compared with those obtained from the P&O controller. The comparison shows that the fuzzy logic controller exhibits a much better behavior.

Beschreibung: This paper presents capacity of the passive decay heat removal system (DHRS) operated under the natural circulation conditions to remove decay heat inside the main vessel of the Lead-bismuth eutectic cooled Fast Reactor (LFR). The motivation of this research is to improve the inherent safety of the LFR based on the China Accelerator Driven System (ADS) engineering project. Usually the plant is damaged due to the failure of the main pumps and the main heat exchangers under the Station Blackout (SBO). To prevent this accident, we proposed the DHRS based on the diathermic oil cooling for the LFR. The behavior of the DHRS and the plant was simulated using the CFD code STAR CCM+ using LFR with DHRS. The purpose of this analysis is to evaluate the heat exchange capacity of the DHRS and is to provide the reference for structural improvement and experimental design. The results show that the stable natural circulations are established in both the main vessel and the DHRS. During the decay process, the heat exchange power is above the core decay heat power. In addition, in-core decay heat and heat storage inside the main vessel are efficiently removed. All the thermal-hydraulics parameters are within a safe range. Moreover, the highest temperature occurs at the upper surface of the core. A swirl occurs at the corner of the lateral core surface and some improvements should be considered. And the natural circulation driving force can be further increased by reducing the loop resistance or increasing the natural circulation height based on the present design scenario to enhance the heat exchange effect.