ALBERT

Description: Propulsion, while conventionally included on the list of important aeronautical disciplines along with aerodynamics, structures, etc., is in itself a systems endeavor, analogous to the engineering of the entire vehicle; indeed propulsion encompasses important aspects of all the other disciplines. In recognition of this fact, the panel focused its discussion on those aspects of the key disciplines that are especially or uniquely important to propulsion. From the initial development of the airplane, the propulsion system has been recognized as one of the pacing technologies. It is perhaps because of the technological disparity between the reciprocating engine and the primitive airframe that the two remained relatively and separate, were developed somewhat independently, usually by different organizations. In recent years, the maturing of the gas turbine power plant and the advance in high-speed airframes have rendered this separation somewhat artificial. The power plant and the airframe now share common structural and aerodynamic elements; as the flight Mach number rises, the degree of interaction increases. By the year 2000, this interdependence will have increased in many respects to a point where independent design may not be practical or possible. During the period since the initiation of the aircraft gas turbine, the solid propellant rocket and the liquid propellant rocket, a vast array of other novel engines have been studied, covering the full spectrum of flight conditions from low subsonic to hypersonic and transatmospheric flight. In each instance, performance limits have been investigated under the assumption that current technology or reasonably foreseeable technology would be available for their development. Among the extensive list of advanced, high-performance concepts and cycles examined are the hypersonic ramjet, the variable cycle, runway-to-orbit airbreathing engine, the ram rocket (airbreathing and rich solid propellant rocket), and the air turborocket. At various times, these systems have come relatively close to meriting development and application. In many instances, limitations of materials and technologies curtailed development. As important and with almost equal frequency, the lack of commercial or military utility of the concept precluded the necessary funding. It is instructive to note that two former items on this list, the turbofan (bypass engine) and the high-speed turboprop, are respectively a mainstay engine and a promising development. In the case of the turbofan, its full potential could not be realized until turbine cooling technology had been developed and new materials developed to permit the construction of transonic fans. In the case of the highspeed turbopropeller engine, not only were the material and turbine technologies needed, but, in addition, the rise in fuel costs provided the impetus to take advantage of its favorable fuel consumption characteristic. As the basic technologies progress and as new missions become attractive, the engines in the foregoing list become candidates for new feasibility studies and further technology development. At the present time, the ram rocket is the prime contender to augment the range of small missiles. Of interest also is the hypersonic ram jet and its logical extension, the runway-to-orbit airbreathing engine. Much of this report deals with the development of current or near-future power plant concepts. First, the motivating factors for aeronautical propulsion research are reviewed as a reminder of the importance of continued effort in a field that has often been characterized as mature. Next, technical areas are discussed in which the panel feels additional research effort is warranted and would lead to the realization of the technological potentials between now and the year 2000. Under these guidelines, new cycles (e.g., isothermal energy exchange) were not considered by the panel. Finally, although facility requirements were not a prime consideration in the current projections, the panel believes that the increasing complexity of propulsion systems; the need for more refined interaction between propulsion system, airframe, and controls; and increasing operation in adverse weather will require test capabilities beyond those now available (see appendix). Enhanced test capability is needed in the areas of propulsion airframe integration and in largescale icing research with proper concurrent treatment of altitude, temperature, and speed.

Description: Results of flow visualization experiments and measurements of the temperature field produced by a single jet and a row of dilution jets issued into a reverse flow combustor are presented. The flow in such combustors is typified by transverse and longitudinal acceleration during the passage through its bending section. The flow visualization experiments were designed to examine the separate effects of longitudinal and transverse acceleration on the jet trajectory and spreading rate. A model describing a dense single jet in a lighter accelerating cross flow is developed. The model is based on integral conservation equations, including the pressure terms appropriate to accelerating flows. It uses a modified entrainment correlation obtained from previous experiments of a jet in a cross stream. The flow visualization results are compared with the model calculations in terms of trajectories and spreading rates. Each experiment is typified by a set of three parameters: momentum ratio, density ratio, and the densimetric Froude number. When injection velocities are large or densities are small, the Froude number becomes very large and hence, unimportant. Therefore, the Froude number is generally significant in describing liquid experiments but is unimportant for the gas experiments in the combustor. Agreement between test and calculated results is encouraging but tends to become poorer with increasing momentum ratio. The temperature measurements are presented primarily in the form of consecutive normalized temperature profiles. Some interpolated isothermal contours are also shown. The single jet trajectories are consistently found to be swept towards the inner wall of the bend, whether injection is from the outer or the inner wall. This behavior is explained by a drifting effect which consists of a transverse velocity component across the combustor due to the developing nature of the flow along it. Plots of lateral temperature distributions of the jet indicate that under longitudinal acceleration conditions the thermal spreading of the jet may be completely suppressed. Comparison between combustor experimental results and model calculations shows poor agreement due to the drifting effect which is not taken into consideration in the model calculations. The row of jets experiments are characterized by two additional parameters: spacing ratio and confinement parameter. The results are shown in the form of consecutive normalized temperature profiles. The confinement parameter appears to become increasingly important with decreasing spacing ratio, in particular when its effect is enhanced by the drifting phenomenon and associated pressure field. A tightly spaced row of jets injected from the inner wall, prior to the bend, is surprisingly kept attached to the inner wall in spite of the strong turning. A similar attachment for a jet injected from the outer wall is not observed.

Description: AiResearch Manufacturing Company, a division of the Garrett Corporation, is engaged in manufacturing a broad variety of products of the aerospace, energy, metals, transit, and marine industries. Products such as fuel controls and rotating accessories for gas turbines are produced by another Garrett division. Computerized analysis is employed to determine how well proposed seals will stand up to stress. For such analysis, AiResearch uses a computer program supplied by COSMIC known as VISCEL. Program saves engineers time in development of software and contributes to improved efficiency in seal analysis.