ALBERT

Description: Recent developments in airfoil-testing methods and fundamental air-flow investigations, as applied to airfoils, are discussed. Preliminary test results, obtained under conditions relatively free from stream turbulence and other disturbances, are presented. Suitable airfoils and airfoil-design principles were developed to take advantage of the unusually extensive laminar boundary layers that may be maintained under the improved testing conditions. The results are of interest mainly in range of below 6,000,000.

Description: Simultaneous air-flow photographs and pressure-distribution measurements have been made of the NACA 4412 airfoil at high speeds in order to determine the physical nature of the compressibility burble. The flow photographs were obtained by the Schlieren method and the pressures were simultaneously measured for 54 stations on the 5-inch-chord wing by means of a multiple-tube photographic manometer. Pressure-measurement results and typical Schlieren photographs are presented. The general nature of the phenomenon called the "compressibility burble" is shown by these experiments. The source of the increased drag is the compression shock that occurs, the excess drag being due to the conversion of a considerable amount of the air-stream kinetic energy into heat at the compression shock.

Description: An investigation was conducted in the N.A.C.A. 20-foot wind tunnel to determine the drag, the propulsive and net efficiencies, and the cooling characteristics of severa1 scale-model arrangements of air-cooled radial-engine nacelles and present-day propellers in front of an 18- percent-thick, 5- by 15-foot airfoil. This report deals with an investigation of wing-nacelle arrangements simulating the geometric proportions of airplanes in the 40,000- to 70,000- pound weight classification and having the nacelles located in the vicinity of the optimum location determined from the earlier tests.

Description: Tests were made in the N.A.C.A. 20-foot wind tunnel on: (1) a wing, of 6.5-foot span, 5.5-foot chord, and 30 percent maximum thickness, fitted with large end plates and (2) a 16-foot span 2.67-foot chord wing of 15 percent maximum thickness to determine the increase in lift obtainable by removing the boundary layer and the power required for the blower. The results of the tests on the stub wing appeared more favorable than previous small-scale tests and indicated that: (1) the suction method was considerably superior to the pressure method, (2) single slots were more effective than multiple slots (where the same pressure was applied to all slots), the slot efficiency increased rapidly for increasing slot widths up to 2 percent of the wing chord and remained practically constant for all larger widths tested, (3) suction pressure and power requirements were quite low (a computation for a light airplane showed that a lift coefficient of 3.0 could be obtained with a suction as low as 2.3 times the dynamic pressure and a power expenditure less than 3 percent of the rated engine power), and (4) the volume of air required to be drawn off was quite high (approximately 0.5 cubic feet per second per unit wing area for an airplane landing at 40 miles per hour with a lift coefficient of 3,0), indicating that considerable duct area must be provided in order to prevent flow losses inside the wing and insure uniform distribution of suction along the span. The results from the tests of the large-span wing were less favorable than those on the stub wing. The reasons for this were, probably: (1) the uneven distribution of suction along the span, (2) the flow losses inside the wing, (3) the small radius of curvature of the leading edge of the wing section, and (4) the low Reynolds Number of these tests, which was about one half that of the stub wing. The results showed a large increase in the maximum lift coefficient with an increase in Reynolds Number in the range of the tests. The results of drag tests showed that the profile drag of the wing was reduced and the L/D ratio was increased throughout the range of lift coefficients corresponding to take-off and climb but that the minimum drag was increased. The slot arrangement that is best for low drag is not the same, however, as that for maximum lift.

Description: Development of airfoil sections suitable for high-speed applications has generally been difficult because little was known of the flow phenomenon that occurs at high speeds. A definite critical speed has been found at which serious detrimental flow changes occur that lead to serious losses in lift and large increases in drag. This flow phenomenon, called the compressibility burble, was originally a propeller problem, but with the development of higher speed aircraft serious consideration must be given to other parts of the airplane. Fundamental investigations of high-speed airflow phenomenon have provided new information. An important conclusion of this work has been the determination of the critical speed, that is, the speed at which the compressibility burble occurs. The critical speed was shown to be the translational velocity at which the sum of the translational velocity and the maximum local induced velocity at the surface of the airfoil or other body equals the local speed of sound. Obviously then higher critical speeds can be attained through the development of airfoils that have minimum induced velocity for any given value of the lift coefficient. Presumably, the highest critical speed will be attained by an airfoil that has uniform chordwise distribution of induced velocity or, in other words, a flat pressure distribution curve. The ideal airfoil for any given high-speed application is, then, that form which at its operating lift coefficient has uniform chordwise distribution of induced velocity. Accordingly, an analytical search for such airfoil forms has been conducted and these forms are now being investigated experimentally in the 23-inch high-speed wind tunnel. The first airfoils investigated showed marked improvement over those forms already available, not only as to critical speed buy also the drag at low speeds is decreased considerably. Because of the immediate marked improvement, it was considered desirable to extend the thickness and lift coefficient ranges for which the original forms had been designed before further extending the investigation.

Description: In order to extend the useful range of Reynolds numbers of airfoils designed to take advantage of the extensive laminar boundary layers possible in an air stream of low turbulence, tests were made of the NACA 2412-34 and 1412-34 sections in the NACA low-turbulence tunnel. Although the possible extent of the laminar boundary layer on these airfoils is not so great as for specially designed laminar-flow airfoils, it is greater than that for conventional airfoils, and is sufficiently extensive so that at Reynolds numbers above 11,000,000 the laminar region is expected to be limited by the permissible 'Reynolds number run' and not by laminar separation as is the case with conventional airfoils. Drag measurements by the wake-survey method and pressure-distribution measurements were made at several lift coefficients through a range of Reynolds numbers up to 11,400,000. The drag scale-effect curve for the NACA 1412-34 is extrapolated to a Reynolds number of 30,000,000 on the basis of theoretical calculations of the skin friction. Comparable skin-friction calculations were made for the NACA 23012. The results indicate that, for certain applications at moderate values of the Reynolds number, the NACA 1412-34 and 2412-34 airfoils offer some advantages over such conventional airfoils as the NACA 23012. The possibility of maintaining a more extensive laminar boundary layer on these airfoils should result in a small drag reduction, and the absence of pressure peaks allows higher speeds to be reached before the compressibility burble is encountered. At lower Reynold numbers, below about 10,000,000, these airfoils have higher drags than airfoils designed to operate with very extensive laminar boundary layers.

Description: An investigation of the interference associated with tail surfaces added to wing-fuselage combinations was included in the interference program in progress in the NACA variable-density tunnel. The results indicate that, in aerodynamically clean combinations, the increment to the high-speed drag can be estimated from section characteristics within useful limits of accuracy. The interference appears mainly as effects on the downwash angel and as losses in the tail. An interference burble, which markedly increases the glide-path angle and the stability in pitch before the actual stall, may be considered a means of obtaining satisfactory stalling characteristics for a complete combination.

Description: The drag characteristics of eight radial-engine cowlings have been determined over a wide speed range in the N.A.C.A. 8-foot high-speed wind tunnel. The pressure distribution over all cowlings was measured, to and above the speed of the compressibility burble, as an aid in interpreting the force tests. One-fifth-scale models of radial-engine cowlings on a wing-nacelle combination mere used in the tests.