ALBERT

Description: Technical Note: Reducing the spin-up time of integrated surface water–groundwater models Hydrology and Earth System Sciences, 18, 5169-5179, 2014 Author(s): H. Ajami, J. P. Evans, M. F. McCabe, and S. Stisen One of the main challenges in the application of coupled or integrated hydrologic models is specifying a catchment's initial conditions in terms of soil moisture and depth-to-water table (DTWT) distributions. One approach to reducing uncertainty in model initialization is to run the model recursively using either a single year or multiple years of forcing data until the system equilibrates with respect to state and diagnostic variables. However, such "spin-up" approaches often require many years of simulations, making them computationally intensive. In this study, a new hybrid approach was developed to reduce the computational burden of the spin-up procedure by using a combination of model simulations and an empirical DTWT function. The methodology is examined across two distinct catchments located in a temperate region of Denmark and a semi-arid region of Australia. Our results illustrate that the hybrid approach reduced the spin-up period required for an integrated groundwater–surface water–land surface model (ParFlow.CLM) by up to 50%. To generalize results to different climate and catchment conditions, we outline a methodology that is applicable to other coupled or integrated modeling frameworks when initialization from an equilibrium state is required.

Description: Extending periodic eddy covariance latent heat fluxes through tree sapflow measurements to estimate long-term total evaporation in a peat swamp forest Hydrology and Earth System Sciences Discussions, 11, 13607-13661, 2014 Author(s): A. D. Clulow, C. S. Everson, M. G. Mengistu, J. S. Price, A. Nickless, and G. P. W. Jewitt A combination of measurement and modelling was used to find a pragmatic solution to estimate the annual total evaporation (ET) from the rare and indigenous Nkazana Peat Swamp Forest (PSF) on the east coast of Southern Africa to improve the water balance estimates within the area. Total evaporation was measured during three window periods (between seven and nine days each) using an eddy covariance (EC) system on a telescopic mast above the forest canopy. Sapflow of an understory and an emergent tree was measured using a low maintenance heat pulse velocity system for an entire hydrological year (October 2009 to September 2010). An empirical model was derived, describing the relationship between the observed ET of the Nkazana PSF measured during two of the window periods ( R 2 = 0.92 and 0.90) which, overlapped with sapflow measurements, thereby providing hourly estimates of predicted ET of the Nkazana PSF for a year, totalling 1125 mm (while rainfall was 650 mm). In building the empirical model, it was found that including the understory tree sapflow provided no benefit to the model performance. In addition, the observed emergent tree sapflow relationship with observed ET between the two field campaigns was consistent and could be represented by a single empirical model ( R 2 = 0.90; RMSE = 0.08 mm). During the window periods of EC measurement, no single meteorological variable was found to describe the Nkazana PSF ET satisfactorily. However, in terms of evaporation models, the hourly FAO56 Penman–Monteith equation best described the observed ET from EC during the August 2009 ( R 2 = 0.75), November 2009 ( R 2 = 0.85) and March 2010 ( R 2 = 0.76) field campaigns, compared to the Priestley–Taylor model ( R 2 = 0.54, 0.74 and 0.62 during the respective field campaigns). From the empirical model of ET and the FAO56 Penman–Monteith equation, a monthly crop factor ( K c ) was derived for the Nkazana PSF providing a method of estimating long-term swamp forest ET from meteorological data. The monthly crop factor indicated two distinct periods. From February to May, it was between 1.2 and 1.4 compared with June to January, when the crop factor was 0.8 to 1.0. The derived monthly K c values were verified as accurate (to one significant digit) using historical data measured at the same site, also using EC, from a~previous study. The measurements provided insights into the microclimate within a subtropical peat swamp forest and the contrasting sapflow of emergent and understory trees. They showed that expensive, high maintenance equipment can be used during manageable window periods in conjunction with low maintenance systems, dedicated to individual trees, to derive a model to estimate long-term ET over remote heterogeneous forests. In addition, the contrast in ET and rainfall emphasises the reliance of the Nkazana PSF on groundwater.

Description: Long-term variability of storm surge frequency in the Venice Lagoon: an update thanks to eighteenth century sea level observations Natural Hazards and Earth System Sciences Discussions, 2, 7465-7486, 2014 Author(s): F. Raicich Sea level observations made in the Venice Lagoon between 1751 and 1792 have been recovered, consisting of two time series of daily data on high and low waters at Venice and Chioggia. From comparisons with modern observations the quality of the 18th century data appears to be good enough to allow a useful analysis. A composite time series of daily mean sea level is obtained by merging the 18th century data and 1872–2004 observations at Venice Punta della Salute. The absence of reliable information on vertical references prevents the connection of the two 18th century time series with each other and with modern observations. However, daily sea level anomalies relative to the mean sea level enable to recognize storm surge events, that appear to occur more frequently in the second half of the 18th century than in the late 19th and 20th centuries, particularly during the 1751–1769 period. The record-breaking storm surge of 4 November 1966 turns out to be a remarkable event also in comparison with the events extracted from the 18th century time series. Further work is required to fill the gap between the old and modern observations.

Description: Ground-penetrating radar observations for estimating the vertical displacement of rotational landslides Natural Hazards and Earth System Sciences Discussions, 2, 7487-7506, 2014 Author(s): C. Lissak, O. Maquaire, J.-P. Malet, F. Lavigne, C. Virmoux, C. Gomez, and R. Davidson The objective of this paper is to demonstrate the applicability of Ground Penetrating Radar (GPR) for monitoring the displacement of slow-moving landslides. GPR data is used to estimate the vertical movement of rotational slides in combination with other surveying techniques. The experimental site is located along the Normandy coast (North East France) here several rotational landslides are continuously affected by a seasonal kinematic pattern (low displacement rates of 0.01 to 0.10 m yr −1 ) and periodically by major acceleration events (high displacement of 1.0 to 7.0 m per event).

Description: Continental Portuguese Territory Flood Susceptibility Index – contribution for a vulnerability index Natural Hazards and Earth System Sciences Discussions, 2, 7521-7552, 2014 Author(s): R. Jacinto, N. Grosso, E. Reis, L. Dias, F. D. Santos, and P. Garrett This work defines a national flood susceptibility index for the Portuguese continental territory, by proposing the aggregation of different variables which represent natural conditions for permeability, runoff and accumulation. This index is part of the national vulnerability index developed in the scope of Flood Maps in Climate Change Scenarios (CIRAC) project, supported by the Portuguese Association of Insurers (APS). This approach expands on previous works by trying to bridge the gap between different floods mechanisms (e.g. progressive and flash floods) occurring at different spatial scales in the Portuguese territory through: (a) selecting homogeneously processed datasets, (b) aggregating their values to better translate the spatially continuous and cumulative influence in floods at multiple spatial scales. Results show a good ability to capture, in the higher susceptibility classes, different flood types: progressive floods and flash floods. Lower values are usually related to: mountainous areas, low water accumulation potential and more permeable soils. Validation with independent flood datasets confirmed these index characteristics, although some overestimation can be seen in the southern region of Alentejo where, due to a dense hydrographic network and an overall low slope, floods are not as frequent as a result of lower precipitation mean values. Future work will focus on: (i) including extreme precipitation datasets to represent the triggering factor, (ii) improving representation of smaller and stepper basins, (iii) optimizing variable weight definition process, (iii) developing more robust independent flood validation datasets.

Description: Dye tracing for investigating flow and transport properties of hydrocarbon-polluted Rabots glaciär, Kebnekaise, Sweden Hydrology and Earth System Sciences Discussions, 11, 13711-13744, 2014 Author(s): C. C. Clason, C. Coch, J. Jarsjö, K. Brugger, P. Jansson, and G. Rosqvist Over 11 000 L of hydrocarbon pollution was deposited on the surface of Rabots glaciär on the Kebnekaise Massif, northern Sweden, following the crash of a Royal Norwegian Air Force aircraft in March 2012. An environmental monitoring programme was subsequently commissioned, including water, snow and ice sampling. The scientific programme further included a series of dye tracing experiments during the 2013 melt season, conducted to investigate flow pathways for pollutants through the glacier hydrological system, and to gain new insight to the internal hydrological system of Rabots glaciär. Results of dye tracing reveal a degree of homogeneity in the topology of the drainage system throughout July and August, with an increase in efficiency as the season progresses, as reflected by decreasing temporary storage and dispersivity. Early onset of melting likely led to formation of an efficient, discrete drainage system early in the melt season, subject to decreasing sinuosity and braiding as the season progressed. Analysis of turbidity-discharge hysteresis further supports the formation of discrete, efficient drainage, with clockwise diurnal hysteresis suggesting easy mobilisation of readily-available sediments in channels. Dye injection immediately downstream of the pollution source zone revealed prolonged storage of dye followed by fast, efficient release. Twinned with a low dye recovery, and supported by sporadic detection of hydrocarbons in the proglacial river, we suggest that meltwater, and thus pollutants in solution, may be released periodically from this zone of the glacier hydrological system. The here identified dynamics of dye storage, dispersion and breakthrough indicate that the ultimate fate and permanence of pollutants in the glacier system is likely to be governed by storage of pollutants in the firn layer and ice mass, or within the internal hydrological system, where it may refreeze. This shows that future studies on the fate of hydrocarbons in pristine, glaciated mountain environments should address the extent to which pollutants in solution act like water molecules or whether they are more susceptible to, for example, refreezing into the surrounding ice, becoming stuck in micro-fractures and pore spaces, or sorption onto subglacial sediments.

Description: The combination of inorganic nanoparticles semiconductor, conjugated polymer, and dye-sensitized in a layer of solar cell is now recognized as potential application in developing flexible, large area, and low cost photovoltaic devices. Several conjugated low bandgap polymers, dyes, and underlayer materials based on the previous studies are quoted in this paper, which can provide guidelines in designing low cost photovoltaic solar cells. All of these materials are designed to help harvest more sunlight in a wider range of the solar spectrum besides enhancing the rate of charge transfer in a device structure. This review focuses on developing solid-state dye-synthesized, polymer, and hybrid solar cells.

Description: Air temperature variability over three glaciers in the Ortles-Cevedale (Italian Alps): effects of glacier disintegration, intercomparison of calculation methods, and impacts on mass balance modeling The Cryosphere Discussions, 8, 6147-6192, 2014 Author(s): L. Carturan, F. Cazorzi, F. De Blasi, and G. Dalla Fontana Glacier mass balance models rely on accurate spatial calculation of input data, in particular air temperature. Lower temperatures (the so-called glacier cooling effect), and lower temperature variability (the so-called glacier damping effect) generally occur over glaciers, compared to ambient conditions. These effects, which depend on the geometric characteristics of glaciers and display a high spatial and temporal variability, have been mostly investigated on medium- to large-size glaciers so far, while observations on smaller ice bodies are scarce. Using a dataset from 8 on-glacier and 4 off-glacier weather stations, collected in summer 2010 and 2011, we analyzed the air temperature variability and wind regime over three different glaciers in the Ortles-Cevedale. The magnitude of the cooling effect and the occurrence of katabatic boundary layer (KBL) processes showed remarkable differences among the three ice bodies, suggesting the likely existence of important reinforcing mechanisms during glacier decay and disintegration. None of the methods proposed in the literature for calculating on-glacier temperature from off-glacier data fully reproduced our observations. Among them, the more physically-based procedure of Greuell and Böhm (1998) provided the best overall results where the KBL prevail, but it was not effective elsewhere (i.e. on smaller ice bodies and close to the glacier margins). The accuracy of air temperature estimations strongly impacted the results from a mass balance model which was applied to the three investigated glaciers. Most importantly, even small temperature deviations caused distortions in parameter calibration, thus compromising the model generalizability.

Description: Currently, electricity distributors make use of various types of equipment divided into levels of automation. This automation enables the integration of elements such as Intelligent Electronic Devices (IEDs) to the supervision of the distribution electrical system, but there is not an appropriate environment to increase the scale of these elements. In this context, the smart grid comes with specifications that allow adding new elements to the intelligence of the power grid operation. However, the cost of communication is still an impediment to the scalability of the integration of these elements into the current structure. In this paper, we propose a middleware that optimizes the communication of this integration using wireless sensor networks (WSN). The goal is to ensure a gradual integration of new elements taking advantage of the increase in the number of sensor nodes in the network due to the scalability of the system itself. The conversion solutions have been used to allow easy communication between the WSN and the smart grid system, and we also have used data aggregation and compression techniques to increase the lifetime of the wireless sensor network.

Description: The sunlight intensity-based global positioning system (SGPS) is able to geolocate outdoor objects by means of the sunlight intensity detection. This paper presents the integration of SGPS into a sensor network in order to improve the overall accuracy using evolutionary algorithms. Another contribution of the paper is to theoretically solve both global and relative positioning of the sensors composing the network within the same framework without satellite-based GPS technology. Results show that this approach is promising and has potential to be improved further.

Description: Indoor localization based on existent WiFi signal strength is becoming more and more prevalent and ubiquitous. Unfortunately, the WiFi received signal strength (RSS) is susceptible by multipath, signal attenuation, and environmental changes, which is the major challenge for accurate indoor localization. To overcome these limitations, we propose the cluster -nearest neighbor (KNN) algorithm with 5 G WiFi signal to reduce the environmental interference and improve the localization performance without additional equipment. In this paper, we propose three approaches to improve the performance of localization algorithm. For one thing, we reduce the computation effort based on the coarse localization algorithm. For another, according to the detailed analysis of the 2.4 G and 5 G signal fluctuation, we expand the real-time measurement RSS before matching the fingerprint map. More importantly, we select the optimal nearest neighbor points based on the proposed cluster KNN algorithm. We have implemented the proposed algorithm and evaluated the performance with existent popular algorithms. Experimental results demonstrate that the proposed algorithm can effectively improve localization accuracy and exhibit superior performance in terms of localization stabilization and computation effort.

Description: Are seasonal calving dynamics forced by buttressing from ice mélange or undercutting by melting? Outcomes from full-Stokes simulations of Store Glacier, West Greenland The Cryosphere, 8, 2353-2365, 2014 Author(s): J. Todd and P. Christoffersen We use a full-Stokes 2-D model (Elmer/Ice) to investigate the flow and calving dynamics of Store Glacier, a fast-flowing outlet glacier in West Greenland. Based on a new, subgrid-scale implementation of the crevasse depth calving criterion, we perform two sets of simulations: one to identify the primary forcing mechanisms and another to constrain future stability. We find that the mixture of icebergs and sea ice, known as ice mélange or sikussak, is principally responsible for the observed seasonal advance of the ice front. On the other hand, the effect of submarine melting on the calving rate of Store Glacier appears to be limited. Sensitivity analysis demonstrates that the glacier's calving dynamics are sensitive to seasonal perturbation, but are stable on interannual timescales due to the strong topographic control on the flow regime. Our results shed light on the dynamics of calving glaciers and may help explain why neighbouring glaciers do not necessarily respond synchronously to changes in atmospheric and oceanic forcing.

Description: Deglaciation of the Caucasus Mountains, Russia/Georgia, in the 21st century observed with ASTER satellite imagery and aerial photography The Cryosphere, 8, 2367-2379, 2014 Author(s): M. Shahgedanova, G. Nosenko, S. Kutuzov, O. Rototaeva, and T. Khromova Changes in the map area of 498 glaciers located on the Main Caucasus ridge (MCR) and on Mt. Elbrus in the Greater Caucasus Mountains (Russia and Georgia) were assessed using multispectral ASTER and panchromatic Landsat imagery with 15 m spatial resolution in 1999/2001 and 2010/2012. Changes in recession rates of glacier snouts between 1987–2001 and 2001–2010 were investigated using aerial photography and ASTER imagery for a sub-sample of 44 glaciers. In total, glacier area decreased by 4.7 ± 2.1% or 19.2 ± 8.7 km 2 from 407.3 ± 5.4 km 2 to 388.1 ± 5.2 km 2 . Glaciers located in the central and western MCR lost 13.4 ± 7.3 km 2 (4.7 ± 2.5%) in total or 8.5 km 2 (5.0 ± 2.4%) and 4.9 km 2 (4.1 ± 2.7%) respectively. Glaciers on Mt. Elbrus, although located at higher elevations, lost 5.8 ± 1.4 km 2 (4.9 ± 1.2%) of their total area. The recession rates of valley glacier termini increased between 1987–2000/01 and 2000/01–2010 (2000 for the western MCR and 2001 for the central MCR and Mt.~Elbrus) from 3.8 ± 0.8, 3.2 ± 0.9 and 8.3 ± 0.8 m yr −1 to 11.9 ± 1.1, 8.7 ± 1.1 and 14.1 ± 1.1 m yr −1 in the central and western MCR and on Mt. Elbrus respectively. The highest rate of increase in glacier termini retreat was registered on the southern slope of the central MCR where it has tripled. A positive trend in summer temperatures forced glacier recession, and strong positive temperature anomalies in 1998, 2006, and 2010 contributed to the enhanced loss of ice. An increase in accumulation season precipitation observed in the northern MCR since the mid-1980s has not compensated for the effects of summer warming while the negative precipitation anomalies, observed on the southern slope of the central MCR in the 1990s, resulted in stronger glacier wastage.

Description: Inversion method for initial tsunami waveform reconstruction Natural Hazards and Earth System Sciences Discussions, 2, 7735-7772, 2014 Author(s): V. V. Voronin, T. A. Voronina, and V. A. Tcheverda This paper deals with the application of r-solution method to recover the initial tsunami waveform in a tsunami source area by remote water-level measurements. Wave propagation is considered within the scope of a linear shallow-water theory. An ill-posed inverse problem is regularized by means of least square inversion using a truncated SVD approach. The properties of obtained solution are determined to a large extent by the properties of an inverse operator, which were numerically investigated. The method presented allows one to control instability of the numerical solution and to obtain an acceptable result in spite of ill-posedness of the problem. It is shown that the accuracy of tsunami source reconstruction strongly depends on the signal-to-noise ratio, the azimuthal coverage of recording stations with respect to the source area and bathymetric features along the wave path. The numerical experiments were carried out with synthetic data and various computational domains including a real bathymetry. The method proposed allows us to make a preliminary prediction of the efficiency of the inversion with a given set of the recording stations and to find out the most informative part of the existing observation system. This essential property of the method can prove to be useful in designing a monitoring system for tsunamis.

Description: Glacier-like forms on Mars The Cryosphere, 8, 2047-2061, 2014 Author(s): B. Hubbard, C. Souness, and S. Brough More than 1300 glacier-like forms (GLFs) are located in Mars' mid-latitudes. These GLFs are predominantly composed of ice–dust mixtures and are visually similar to terrestrial valley glaciers, showing signs of downhill viscous deformation and an expanded former extent. However, several fundamental aspects of their behavior are virtually unknown, including temporal and spatial variations in mass balance, ice motion, landscape erosion and deposition, and hydrology. Here, we investigate the physical glaciology of martian GLFs. We use satellite images of specific examples and case studies to build on existing knowledge relating to (i) GLF current and former extent, exemplified via a GLF located in Phlegra Montes; (ii) indicators of GLF motion, focusing on the presence of surface crevasses on several GLFs; (iii) processes of GLF debris transfer, focusing on mapping and interpreting boulder trains on one GLF located in Protonilus Mensae, the analysis of which suggests a best-estimate mean GLF flow speed of 7.5 mm a −1 ; and (iv) GLF hydrology, focusing on supra-GLF gulley networks. On the basis of this information, we summarize the current state of knowledge of the glaciology of martian GLFs and identify future research avenues.

Description: Strategy of valid 14 C dates choice in syngenetic permafrost The Cryosphere Discussions, 8, 5589-5621, 2014 Author(s): Y. K. Vasil'chuk and A. C. Vasil'chuk The main problem of radiocarbon dating within permafrost is the uncertain reliability of the 14 C dates. Syngenetic sediments contain allochthonous organic deposit that originated at a distance from its present position. Due to the very good preservation of organic materials in permafrost conditions and numerous re-burials of the fossils from ancient deposits into younger ones the dates could be both younger and older than the true age of dated material. The strategy for the most authentic radiocarbon date selection for dating of syncryogenic sediments is considered taking into account the fluvial origin of the syngenetic sediments. The re-deposition of organic material is discussed in terms of cyclic syncryogenic sedimentation and also the possible re-deposition of organic material in subaerial-subaqueous conditions. The advantages and the complications of dating organic micro-inclusions from ice wedges by the accelerator mass spectrometry (AMS) method are discussed applying to true age of dated material search. Radiocarbon dates of different organic materials from the same samples are compared. The younger age of the yedoma from cross-sections of Duvanny Yar in Kolyma River and Mamontova Khayata in the mouth of Lena River is substantiated due to the principle of the choice of the youngest 14 C date from the set.

Description: Modeling the elastic transmission of tidal stresses to great distances inland in channelized ice streams The Cryosphere, 8, 2007-2029, 2014 Author(s): J. Thompson, M. Simons, and V. C. Tsai Geodetic surveys suggest that ocean tides can modulate the motion of Antarctic ice streams, even at stations many tens of kilometers inland from the grounding line. These surveys suggest that ocean tidal stresses can perturb ice stream motion at distances about an order of magnitude farther inland than tidal flexure of the ice stream alone. Recent models exploring the role of tidal perturbations in basal shear stress are primarily one- or two-dimensional, with the impact of the ice stream margins either ignored or parameterized. Here, we use two- and three-dimensional finite-element modeling to investigate transmission of tidal stresses in ice streams and the impact of considering more realistic, three-dimensional ice stream geometries. Using Rutford Ice Stream as a real-world comparison, we demonstrate that the assumption that elastic tidal stresses in ice streams propagate large distances inland fails for channelized glaciers due to an intrinsic, exponential decay in the stress caused by resistance at the ice stream margins. This behavior is independent of basal conditions beneath the ice stream and cannot be fit to observations using either elastic or nonlinear viscoelastic rheologies without nearly complete decoupling of the ice stream from its lateral margins. Our results suggest that a mechanism external to the ice stream is necessary to explain the tidal modulation of stresses far upstream of the grounding line for narrow ice streams. We propose a hydrologic model based on time-dependent variability in till strength to explain transmission of tidal stresses inland of the grounding line. This conceptual model can reproduce observations from Rutford Ice Stream.

Description: Simulating the Antarctic ice sheet in the Late-Pliocene warm period: PLISMIP-ANT, an ice-sheet model intercomparison project The Cryosphere Discussions, 8, 5539-5588, 2014 Author(s): B. de Boer, A. M. Dolan, J. Bernales, E. Gasson, H. Goelzer, N. R. Golledge, J. Sutter, P. Huybrechts, G. Lohmann, I. Rogozhina, A. Abe-Ouchi, F. Saito, and R. S. W. van de Wal In the context of future climate change, understanding the nature and behaviour of ice sheets during warm intervals in Earth history is of fundamental importance. The Late-Pliocene warm period (also known as the PRISM interval: 3.264 to 3.025 million years before present) can serve as a potential analogue for projected future climates. Although Pliocene ice locations and extents are still poorly constrained, a significant contribution to sea-level rise should be expected from both the Greenland ice sheet and the West and East Antarctic ice sheets based on palaeo sea-level reconstructions. Here, we present results from simulations of the Antarctic ice sheet by means of an international Pliocene Ice Sheet Modeling Intercomparison Project (PLISMIP-ANT). For the experiments, ice-sheet models including the shallow ice and shelf approximations have been used to simulate the complete Antarctic domain (including grounded and floating ice). We compare the performance of six existing numerical ice-sheet models in simulating modern control and Pliocene ice sheets by a suite of four sensitivity experiments. Ice-sheet model forcing fields are taken from the HadCM3 atmosphere–ocean climate model runs for the pre-industrial and the Pliocene. We include an overview of the different ice-sheet models used and how specific model configurations influence the resulting Pliocene Antarctic ice sheet. The six ice-sheet models simulate a comparable present-day ice sheet, although the models are setup with their own parameter settings. For the Pliocene simulations using the Bedmap1 bedrock topography, some models show a small retreat of the East Antarctic ice sheet, which is thought to have happened during the Pliocene for the Wilkes and Aurora basins. This can be ascribed to either the surface mass balance, as the HadCM3 Pliocene climate shows a significant increase over the Wilkes and Aurora basin, or the initial bedrock topography. For the latter, our simulations with the recently published Bedmap2 bedrock topography indicate a significantly larger contribution to Pliocene sea-level rise from the East Antarctic ice sheet for all six models relative to the simulations with Bedmap1.

Description: Fluctuations of a Greenlandic tidewater glacier driven by changes in atmospheric forcing: observations and modelling of Kangiata Nunaata Sermia, 1859–present The Cryosphere, 8, 2031-2045, 2014 Author(s): J. M. Lea, D. W. F. Mair, F. M. Nick, B. R. Rea, D. van As, M. Morlighem, P. W. Nienow, and A. Weidick Many tidewater glaciers in Greenland are known to have undergone significant retreat during the last century following their Little Ice Age maxima. Where it is possible to reconstruct glacier change over this period, they provide excellent records for comparison to climate records, as well as calibration/validation for numerical models. These glacier change records therefore allow for tests of numerical models that seek to simulate tidewater glacier behaviour over multi-decadal to centennial timescales. Here we present a detailed record of behaviour from Kangiata Nunaata Sermia (KNS), SW Greenland, between 1859 and 2012, and compare it against available oceanographic and atmospheric temperature data between 1871 and 2012. We also use these records to evaluate the ability of a well-established one-dimensional flow-band model to replicate behaviour for the observation period. The record of terminus change demonstrates that KNS has advanced/retreated in phase with atmosphere and ocean climate anomalies averaged over multi-annual to decadal timescales. Results from an ensemble of model runs demonstrate that observed dynamics can be replicated. Model runs that provide a reasonable match to observations always require a significant atmospheric forcing component, but do not necessarily require an oceanic forcing component. Although the importance of oceanic forcing cannot be discounted, these results demonstrate that changes in atmospheric forcing are likely to be a primary driver of the terminus fluctuations of KNS from 1859 to 2012. We propose that the detail and length of the record presented makes KNS an ideal site for model validation exercises investigating links between climate, calving rates, and tidewater glacier dynamics.

Description: Hydrogeology of an Alpine rockfall aquifer system and its role in flood attenuation and maintaining baseflow Hydrology and Earth System Sciences, 18, 4437-4452, 2014 Author(s): U. Lauber, P. Kotyla, D. Morche, and N. Goldscheider The frequency and intensity of extreme hydrological events in Alpine regions is projected to increase with climate change. The goal of this study is to better understand the functioning of aquifers composed of complex alluvial and rockfall deposits in Alpine valleys and to quantify the role of these natural storage spaces in flood attenuation and baseflow maintenance. Geomorphological and hydrogeological mapping, tracer tests, and continuous flow measurements were conducted in the Reintal (German Alps), where runoff from a karst spring infiltrates a series of postglacial alluvial/rockfall aquifers. During high-flow conditions, groundwater velocities of 30 m h −1 were determined along 500 m; hydrograph analyses revealed short lag times (5 h) between discharge peaks upstream and downstream from the aquifer series; the maximum discharge ratio downstream (22) and the peak recession coefficient (0.196 d −1 ) are low compared with other Alpine catchments. During low-flow conditions, the underground flow path length increased to 2 km and groundwater velocities decreased to 13 m h −1 . Downstream hydrographs revealed a delayed discharge response after 101 h and peaks damped by a factor of 1.5. These results indicate that alluvial/rockfall aquifers might play an important role in the flow regime and attenuation of floods in Alpine regions.

Description: Observed groundwater temperature response to recent climate change Hydrology and Earth System Sciences, 18, 4453-4466, 2014 Author(s): K. Menberg, P. Blum, B. L. Kurylyk, and P. Bayer Climate change is known to have a considerable influence on many components of the hydrological cycle. Yet, the implications for groundwater temperature, as an important driver for groundwater quality, thermal use and storage, are not yet comprehensively understood. Furthermore, few studies have examined the implications of climate-change-induced groundwater temperature rise for groundwater-dependent ecosystems. Here, we examine the coupling of atmospheric and groundwater warming by employing stochastic and deterministic models. Firstly, several decades of temperature time series are statistically analyzed with regard to climate regime shifts (CRSs) in the long-term mean. The observed increases in shallow groundwater temperatures can be associated with preceding positive shifts in regional surface air temperatures, which are in turn linked to global air temperature changes. The temperature data are also analyzed with an analytical solution to the conduction–advection heat transfer equation to investigate how subsurface heat transfer processes control the propagation of the surface temperature signals into the subsurface. In three of the four monitoring wells, the predicted groundwater temperature increases driven by the regime shifts at the surface boundary condition generally concur with the observed groundwater temperature trends. Due to complex interactions at the ground surface and the heat capacity of the unsaturated zone, the thermal signals from distinct changes in air temperature are damped and delayed in the subsurface, causing a more gradual increase in groundwater temperatures. These signals can have a significant impact on large-scale groundwater temperatures in shallow and economically important aquifers. These findings demonstrate that shallow groundwater temperatures have responded rapidly to recent climate change and thus provide insight into the vulnerability of aquifers and groundwater-dependent ecosystems to future climate change.

Description: Near infrared radiation (NIR) has been used to enable the sintering of TiO2 films on fluorine-doped tin oxide (FTO) glass in 12.5 s. The 9 µm thick TiO2 films were constructed into working electrodes for dye-sensitized solar cells (DSCs) achieving similar photovoltaic performance to TiO2 films prepared by heating for 30 min in a convection oven. The ability of the FTO glass to heat upon 12.5 s exposure of NIR radiation was measured using an IR camera and demonstrated a peak temperature of 680°C; glass without the 600 nm FTO layer reached 350°C under identical conditions. In a typical DSC heating step, a TiO2 based paste is heated until the polymeric binder is removed leaving a mesoporous film. The weight loss associated with this step, as measured using thermogravimetric analysis, has been used to assess the efficacy of the FTO glass to heat sufficiently. Heat induced interparticle connectivity in the TiO2 film has also been assessed using optoelectronic transient measurements that can identify electron lifetime through the TiO2 film. An NIR treated device produced in 12.5 seconds shows comparable binder removal, electron lifetime, and efficiency to a device manufactured over 30 minutes in a conventional oven.

Description: Band gap engineering provides an opportunity to not only provide higher overall conversion efficiencies of the reference AM1.5 spectra but also customize PV device design for specific geographic locations and microenvironments based on atmospheric conditions characteristic to that particular location. Indium gallium nitride and other PV materials offer the opportunity for limited bandgap engineering to match spectra. The effects of atmospheric conditions such as aerosols, cloud cover, water vapor, and air mass have been shown to cause variations in spectral radiance that alters PV system performance due to both overrating and underrating. Designing PV devices optimized for spectral radiance of a particular region can result in improved PV system performance. This paper presents a new method for designing geographically optimized PV cells with using a numerical model for bandgap optimization. The geographic microclimate spectrally resolved solar flux for twelve representative atmospheric conditions for the incident radiation angle (zenith angle) of 48.1° and fixed array angle of 40° is used to iteratively optimize the band gap for tandem, triple, and quad-layer of InGaN-based multijunction cells. The results of this method are illustrated for the case study of solar farms in the New York region and discussed.

Description: We report here a prototype laboratory setup for detecting ethylene (C2H4) in ppm level employing a sensor made of multiwalled carbon nanotubes of 40 nm average tube diameter. The proposed reversible chemoresistive ethylene sensor is fabricated using Kapton as the substrate onto which carbon nanotubes are coated using thick film technology. IDT silver electrodes are printed using piezo head based ink-jet printing technology. The increases in electrical resistance of the sensor element are measured on exposure to ethylene for different ethylene concentrations using a potentiostat and data acquisition system. The increase in resistance of the calibrated sensor element on exposure to ethylene (analyte) is about 18.4% at room temperature for 50 ppm ethylene concentration. This change is reversible. Our sensor element exhibits a better performance than those reported earlier (1.8%) and it has got the rise and fall time of 10 s and 60 s, respectively. It could be used for testing the ripening of fruits.

Description: Snow mass decrease in the Northern Hemisphere (1979/80–2010/11) The Cryosphere Discussions, 8, 5623-5644, 2014 Author(s): Z. Li, J. Liu, L. Huang, N. Wang, B. Tian, J. Zhou, Q. Chen, and P. Zhang Snow cover has a key effect on climate change and hydrological cycling, as well as water supply to a sixth of the world's population across the Northern Hemisphere. However, reliable data on trends in snow cover in the Northern Hemisphere is lacking. Snow water equivalent (SWE) is a common measure of the amount of equivalent water of the snow pack. Here we verify the accuracy of three existing global SWE products and merge the most accurate aspects of them to generate a new SWE product covering the last 32 years (1979/80–2010/11). Using this new SWE product, we show that there has been a significant decreasing trend in the total mass of snow in the Northern Hemisphere. The most notable changes in total snow mass are −16.45 ± 6.68 and −13.55 ± 7.80 Gt year −1 in January and February, respectively. These are followed by March and December, which have trends of −12.58 ± 6.88 and −10.70 ± 5.62 Gt year −1 , respectively, from 1979/80 to 2010/11. During the same period, the temperature in the study area raised 0.17 °C decade −1 , which is thought to be the main reason of SWE decline.

Description: Factors controlling Slope Environmental Lapse Rate (SELR) of temperature in the monsoon and cold-arid glacio-hydrological regimes of the Himalaya The Cryosphere Discussions, 8, 5645-5686, 2014 Author(s): R. J. Thayyen and A. P. Dimri Moisture, temperature and precipitation interplay forced through the orographic processes sustains the Himalayan cryospheric system. However, factors controlling the Slope Environmental Lapse Rate (SELR) of temperature along the higher Himalayan mountain slopes across various glacio-hydrologic regimes remain as a key knowledge gap. Present study dwells on the orographic processes driving the moisture–temperature interplay in the monsoon and cold-arid glacio-hydrological regimes of the Himalaya. Systematic data collection at three altitudes between 2540 and 3763 m a.s.l. in the Garhwal Himalaya (hereafter called monsoon regime) and between 3500 and 5600 m a.s.l. in the Ladakh Himalaya (herefater called cold-arid regime) revealed moistrue control on temperature distribution at temporal and spatial scales. Observed daily SELR of temperature ranges between 9.0 to 1.9 °C km −1 and 17.0 to 2.8 °C km −1 in the monsoon and cold-arid regimes respectively highlighting strong regional variability. Moisture influx to the region, either from Indian summer monsoon (ISM) or from Indian winter monsoon (IWM) forced lowering of SELR. This phenophena of "monsoon lowering" of SELR is due to the release latent heat of condensation from orographically focred lifted air parcel. Seasonal response of SELR in the monsoon regime is found to be closly linked with the variations in the local lifting condensation levels (LCL). Contrary to this, cold-arid system is characterised by the extremely high values of daily SELR upto 17 °C km −1 signifying the extremely arid conditions prevailing in summer. Distinctly lower SELR devoid of monsoon lowering at higher altitude sections of monsoon and cold-arid regimes suggests sustained wetter high altitude regimes. We have proposed a SELR model for both glacio-hydrological regimes demostrating with two sections each using a derivative of the Clausius–Clapeyron relationship by deriving monthly SELR indices. It has been proposed that the manifestations of presence or absence of moisture is the single most important factor determining the temperature distribution along the higher Himalayan slopes driven by the orographic forcings. This work also suggests that the arbitary use of temperature lapse rate to extrapolate temperature to the higher Himalaya is extremely untenable.

Description: Evaluation of the satellite-based Global Flood Detection System for measuring river discharge: influence of local factors Hydrology and Earth System Sciences, 18, 4467-4484, 2014 Author(s): B. Revilla-Romero, J. Thielen, P. Salamon, T. De Groeve, and G. R. Brakenridge One of the main challenges for global hydrological modelling is the limited availability of observational data for calibration and model verification. This is particularly the case for real-time applications. This problem could potentially be overcome if discharge measurements based on satellite data were sufficiently accurate to substitute for ground-based measurements. The aim of this study is to test the potentials and constraints of the remote sensing signal of the Global Flood Detection System for converting the flood detection signal into river discharge values. The study uses data for 322 river measurement locations in Africa, Asia, Europe, North America and South America. Satellite discharge measurements were calibrated for these sites and a validation analysis with in situ discharge was performed. The locations with very good performance will be used in a future project where satellite discharge measurements are obtained on a daily basis to fill the gaps where real-time ground observations are not available. These include several international river locations in Africa: the Niger, Volta and Zambezi rivers. Analysis of the potential factors affecting the satellite signal was based on a classification decision tree (random forest) and showed that mean discharge, climatic region, land cover and upstream catchment area are the dominant variables which determine good or poor performance of the measure\-ment sites. In general terms, higher skill scores were obtained for locations with one or more of the following characteristics: a river width higher than 1km; a large floodplain area and in flooded forest, a potential flooded area greater than 40%; sparse vegetation, croplands or grasslands and closed to open and open forest; leaf area index 〉 2; tropical climatic area; and without hydraulic infrastructures. Also, locations where river ice cover is seasonally present obtained higher skill scores. This work provides guidance on the best locations and limitations for estimating discharge values from these daily satellite signals.

Description: Sampling frequency trade-offs in the assessment of mean transit times of tropical montane catchment waters under semi-steady-state conditions Hydrology and Earth System Sciences Discussions, 11, 12443-12488, 2014 Author(s): E. Timbe, D. Windhorst, R. Celleri, L. Timbe, P. Crespo, H.-G. Frede, J. Feyen, and L. Breuer Stream and soil waters were collected on a weekly basis in a tropical montane cloud forest catchment for two years and analyzed for stable water isotopes in order to infer transit time distribution functions and to define the mean transit times. Depending on the water type (stream or soil water), lumped distribution functions such as Exponential-Piston flow, Linear-Piston flow and Gamma models using temporal isotopic variations of precipitation event samples as input, were fitted. Samples were aggregated to daily, weekly, biweekly, monthly and bimonthly time scales in order to check the sensitivity of temporal sampling on model predictions. The study reveals that the effect of decreasing sampling frequency depends on the water type. For soil waters with transit times in the order of weeks to months, there was a clear trend of over prediction. In contrast, the trend of prediction for stream waters, with a dampened isotopic signal and mean transit times in the order of 2 to 4 years, was less clear and depending on the type of model used. The trade-off to coarse data resolutions could potentially lead to misleading conclusions on how water actually moves through the catchment, while at the same time predictions can reach better fitting efficiencies, lesser uncertainties, errors and biases. For both water types an optimal sampling frequency seems to be one or at most two weeks. The results of our analyses provide information for the planning (in particular in terms of cost-benefit and time requirements) of future fieldwork in similar Andean or other catchments.

Description: A model study of Abrahamsenbreen, a surging glacier in northern Spitsbergen The Cryosphere Discussions, 8, 5687-5726, 2014 Author(s): J. Oerlemans and W. J. J. van Pelt The climate sensitivity of Abrahamsenbreen, a 20 km long surge-type glacier in northern Spitsbergen, is studied with a simple glacier model. A scheme to describe the surges is included, which makes it possible to account for the effect of surges on the total mass budget of the glacier. A climate reconstruction back to AD 1300, based on ice-core data from Lomonosovfonna and climate records from Longyearbyen, is used to drive the model. The model is calibrated by requesting that it produces the correct Little Ice Age maximum glacier length and simulates the observed magnitude of the 1978-surge. Abrahamsenbreen is strongly out of balance with the current climate. If climatic conditions will remain as they were for the period 1989–2010, the glacier will ultimately shrink to a length of about 4 km (but this will take hundreds of years). For a climate change scenario involving a 2 m yr −1 rise of the equilibrium line from now onwards, we predict that in the year 2100 Abrahamsenbreen will be about 12 km long. The main effect of a surge is to lower the mean surface elevation and to increase the ablation area, thereby causing a negative perturbation of the mass budget. We found that the occurrence of surges leads to a somewhat stronger retreat of the glacier in a warming climate. Because of the very small bed slope, Abrahamsenbreen is sensitive to small perturbations in the equilibrium-line altitude E . For a decrease of E of only 160 m, the glacier would steadily grow into the Woodfjorddalen until after 2000 years it would reach the Woodfjord and calving could slow down the advance.

Description: Technical Note: On the Matt–Shuttleworth approach to estimate crop water requirements Hydrology and Earth System Sciences, 18, 4341-4348, 2014 Author(s): J. P. Lhomme, N. Boudhina, and M. M. Masmoudi The Matt–Shuttleworth method provides a way to make a one-step estimate of crop water requirements with the Penman–Monteith equation by translating the crop coefficients, commonly available in United Nations Food and Agriculture Organization (FAO) publications, into equivalent surface resistances. The methodology is based upon the theoretical relationship linking crop surface resistance to a crop coefficient and involves the simplifying assumption that the reference crop evapotranspiration (ET 0 ) is equal to the Priestley–Taylor estimate with a fixed coefficient of 1.26. This assumption, used to eliminate the dependence of surface resistance on certain weather variables, is questionable; numerical simulations show that it can lead to substantial differences between the true value of surface resistance and its estimate. Consequently, the basic relationship between surface resistance and crop coefficient, without any assumption, appears to be more appropriate for inferring crop surface resistance, despite the interference of weather variables.

Description: Variational assimilation of remotely sensed flood extents using a 2-D flood model Hydrology and Earth System Sciences, 18, 4325-4339, 2014 Author(s): X. Lai, Q. Liang, H. Yesou, and S. Daillet A variational data assimilation (4D-Var) method is proposed to directly assimilate flood extents into a 2-D dynamic flood model to explore a novel way of utilizing the rich source of remotely sensed data available from satellite imagery for better analyzing or predicting flood routing processes. For this purpose, a new cost function is specially defined to effectively fuse the hydraulic information that is implicitly indicated in flood extents. The potential of using remotely sensed flood extents for improving the analysis of flood routing processes is demonstrated by applying the present new data assimilation approach to both idealized and realistic numerical experiments.

Description: Quantitative high-resolution observations of soil water dynamics in a complicated architecture with time-lapse Ground-Penetrating Radar Hydrology and Earth System Sciences Discussions, 11, 12365-12404, 2014 Author(s): P. Klenk, S. Jaumann, and K. Roth High-resolution time-lapse Ground-Penetrating Radar (GPR) observations of advancing and retreating water tables can yield a wealth of information about near-surface water content dynamics. In this study, we present and analyze a series of imbibition, drainage and infiltration experiments which have been carried out at our artificial ASSESS test site and observed with surface based GPR. The test site features a complicated but known subsurface architecture constructed with three different kinds of sand. It allows studying soil water dynamics with GPR under a wide range of different conditions. Here, we assess in particular (i) the accurate determination of soil water dynamics averaged over the whole vertical extent by evaluating the bottom reflection and (ii) the feasibility of monitoring the dynamic shape of the capillary fringe reflection. The phenomenology of the GPR response of a dynamically changing capillary fringe is developed from a soil physical point of view. We then explain experimentally observed phenomena based on numerical simulations of both the water content dynamics and the expected GPR response.

Description: Translating aboveground cosmic-ray neutron intensity to high-frequency soil moisture profiles at sub-kilometer scale Hydrology and Earth System Sciences, 18, 4363-4379, 2014 Author(s): R. Rosolem, T. Hoar, A. Arellano, J. L. Anderson, W. J. Shuttleworth, X. Zeng, and T. E. Franz Above-ground cosmic-ray neutron measurements provide an opportunity to infer soil moisture at the sub-kilometer scale. Initial efforts to assimilate those measurements have shown promise. This study expands such analysis by investigating (1) how the information from aboveground cosmic-ray neutrons can constrain the soil moisture at distinct depths simulated by a land surface model, and (2) how changes in data availability (in terms of retrieval frequency) impact the dynamics of simulated soil moisture profiles. We employ ensemble data assimilation techniques in a "nearly-identical twin" experiment applied at semi-arid shrubland, rainfed agricultural field, and mixed forest biomes in the USA. The performance of the Noah land surface model is compared with and without assimilation of observations at hourly intervals, as well as every 2 days. Synthetic observations of aboveground cosmic-ray neutrons better constrain the soil moisture simulated by Noah in root-zone soil layers (0–100cm), despite the limited measurement depth of the sensor (estimated to be 12–20cm). The ability of Noah to reproduce a "true" soil moisture profile is remarkably good, regardless of the frequency of observations at the semi-arid site. However, soil moisture profiles are better constrained when assimilating synthetic cosmic-ray neutron observations hourly rather than every 2 days at the cropland and mixed forest sites. This indicates potential benefits for hydrometeorological modeling when soil moisture measurements are available at a relatively high frequency. Moreover, differences in summertime meteorological forcing between the semi-arid site and the other two sites may indicate a possible controlling factor to soil moisture dynamics in addition to differences in soil and vegetation properties.

Description: Large-scale 3-D modeling by integration of resistivity models and borehole data through inversion Hydrology and Earth System Sciences, 18, 4349-4362, 2014 Author(s): N. Foged, P. A. Marker, A. V. Christansen, P. Bauer-Gottwein, F. Jørgensen, A.-S. Høyer, and E. Auken We present an automatic method for parameterization of a 3-D model of the subsurface, integrating lithological information from boreholes with resistivity models through an inverse optimization, with the objective of further detailing of geological models, or as direct input into groundwater models. The parameter of interest is the clay fraction, expressed as the relative length of clay units in a depth interval. The clay fraction is obtained from lithological logs and the clay fraction from the resistivity is obtained by establishing a simple petrophysical relationship, a translator function, between resistivity and the clay fraction. Through inversion we use the lithological data and the resistivity data to determine the optimum spatially distributed translator function. Applying the translator function we get a 3-D clay fraction model, which holds information from the resistivity data set and the borehole data set in one variable. Finally, we use k -means clustering to generate a 3-D model of the subsurface structures. We apply the procedure to the Norsminde survey in Denmark, integrating approximately 700 boreholes and more than 100 000 resistivity models from an airborne survey in the parameterization of the 3-D model covering 156 km 2 . The final five-cluster 3-D model differentiates between clay materials and different high-resistivity materials from information held in the resistivity model and borehole observations, respectively.

Description: Simulating long-term past changes in the balance between water demand and availability and assessing their main drivers at the river basin management scale Hydrology and Earth System Sciences Discussions, 11, 12315-12364, 2014 Author(s): J. Fabre, D. Ruelland, A. Dezetter, and B. Grouillet The aim of this study was to assess the balance between water demand and availability and its spatial and temporal variability from 1971 to 2009 in the Herault (2500 km 2 , France) and the Ebro (85 000 km 2 , Spain) catchments. Natural streamflow was evaluated using a conceptual hydrological model. The regulation of river flow was accounted for through a widely applicable demand-driven reservoir management model applied to the largest dam in the Herault basin and to 11 major dams in the Ebro basin. Urban water demand was estimated from population and monthly unit water consumption data. Water demand for irrigation was computed from irrigated area, crop and soil data, and climatic forcing. Finally, a series of indicators comparing water supply and water demand at strategic resource and demand nodes were computed at a 10 day time step. Variations in water stress in each catchment over the past 40 years were successfully modeled, taking into account climatic and anthropogenic pressures and changes in water management strategies over time. Observed changes in discharge were explained by separating human and hydro-climatic pressures on water resources: respectively 20 and 3% of the decrease in the Ebro and the Herault discharges were linked to human-induced changes. Although key areas of the Herault basin were shown to be highly sensitive to hydro-climatic variability, the balance between water uses and availability in the Ebro basin appears to be more critical, owing to high agricultural pressure on water resources. The proposed modeling framework is currently being used to assess water stress under climatic and socio-economic prospective scenarios. Further research will investigate the effectiveness of adaptation policies aimed at maintaining the balance between water use and availability.

Description: Time-series analysis of the long-term hydrologic impacts of afforestation in the Águeda watershed of North-Central Portugal Hydrology and Earth System Sciences Discussions, 11, 12223-12256, 2014 Author(s): D. Hawtree, J. P. Nunes, J. J. Keizer, R. Jacinto, J. Santos, M. E. Rial-Rivas, A.-K. Boulet, F. Tavares-Wahren, and K.-H. Feger The north-central region of Portugal has undergone significant afforestation of the species Pinus pinaster and Eucalyptus globulus since the early 1900s; however, the long-term hydrologic impacts of this land cover change are not fully understood. To contribute to a better understanding of the potential hydrologic impacts of this land cover change, this study examines the temporal trends in 7 years of data from the Águeda watershed (part of the Vouga Basin) over the period of 1936 to 2010. Meteorological and hydrological records were analysed using a combined Thiel–Sen/Mann–Kendall trend testing approach, to assess the magnitude and significance of patterns in the observed data. These trend tests indicated that there had been no significant reduction in streamflow yield over either the entire test period, or during sub-record periods, despite the large-scale afforestation which had taken place. This lack of change is attributed to both the characteristics of the watershed and the nature of the land cover change. By contrast, a number of significant trends were found for baseflow index, which showed positive trends in the early data record (primarily during Pinus pinaster afforestation), followed by a reversal to negative trends later in the data record (primarily during Eucalyptus globulus afforestation). These changes are attributed to vegetation impacts on streamflow generating processes, both due to the species differences and to alterations in soil properties (i.e. promoting water repellency of the topsoil). These results highlight the importance of considering both vegetation types/dynamics and watershed characteristic when assessing hydrologic impacts, in particular with respect to soil properties.

Description: Reply to D. L. Peters' comment on "Streamflow input to Lake Athabasca, Canada" by Rasouli et al. (2013) Hydrology and Earth System Sciences Discussions, 11, 12257-12270, 2014 Author(s): K. Rasouli, M. A. Hernández-Henríquez, and S. J. Déry This paper provides a reply to a comment from Peters (2014) on our recent effort focused on evaluating changes in streamflow input to Lake Athabasca, Canada. Lake Athabasca experienced a 21.2% decline in streamflow input between 1960 and 2010 that has led to a marked decline in its water levels in recent decades. A reassessment of trends in naturalized Lake Athabasca water levels shows insignificant changes from our previous findings reported in Rasouli et al. (2013), and hence our previous conclusions remain unchanged. The reply closes with recommendations for future research to minimize uncertainties in historical assessments of trends in Lake Athabasca water levels and to better project its future water levels driven by climate change and anthropogenic activities in the Athabasca Lake Basin.

Description: Is sinuosity a function of slope and bankfull discharge? – A case study of the meandering rivers in the Pannonian Basin Hydrology and Earth System Sciences Discussions, 11, 12271-12290, 2014 Author(s): J. Petrovszki, G. Timár, and G. Molnár Pre-regulation channel sinuosities of the meandering rivers of the Pannonian Basin are analysed in order to define a mathematical model to estimate the influence of the bankfull discharge and the channel slope on them. As a primary database, data triplets of slope, discharge and sinuosity values were extracted from historical and modern datasets and pre-regulation historical topographic maps. Channel slope values were systematically modified to estimate figures valid before the river regulation works. The bankfull discharges were estimated from the average discharges using a robust yet complex method. The "classical" graphs of Leopold and Wolman (1957), Ackers and Charlton (1970b) and Schumm and Khan (1972) were compiled to a set up a theoretical surface, whose parameters are estimated by the real values of the above database, containing characteristics of the Pannonian Basin rivers. As a result it occurred that there is a two-dimensional function of the bankfull discharges, which provides a good estimation of the most probable sinuosity values of the rivers with the given slope and discharge characteristics. The average RMS error of this estimation is around 15% on this dataset and believed to be the effect of the non-analysed changes in the sediment discharge and size distribution.

Description: Technical Note: Field experiences using UV/VIS sensors for high-resolution monitoring of nitrate in groundwater Hydrology and Earth System Sciences Discussions, 11, 12291-12314, 2014 Author(s): M. Huebsch, F. Grimmeisen, M. Zemann, O. Fenton, K. G. Richards, P. Jordan, A. Sawarieh, P. Blum, and N. Goldscheider Two different in-situ spectrophotometers are compared that were used in the field to determine nitrate-nitrogen (NO 3 -N) concentrations at two distinct spring discharge sites. One sensor was a double wavelength spectrophotometer (DWS) and the other a multiple wavelength spectrophotometer (MWS). The objective of the study was to review the hardware options, determine ease of calibration, accuracy, influence of additional substances and to assess positive and negative aspects of the two sensors as well as troubleshooting and trade-offs. Both sensors are sufficient to monitor highly time-resolved NO 3 -N concentrations in emergent groundwater. However, the chosen path length of the sensors had a significant influence on the sensitivity and the range of detectable NO 3 -N. The accuracy of the calculated NO 3 -N concentrations of the sensors can be affected, if the content of additional substances such as turbidity, organic matter, nitrite or hydrogen carbonate significantly varies after the sensors have been calibrated to a particular water matrix. The MWS offers more possibilities for calibration and error detection, but requires more expertise compared with the DWS.

Description: A small planar modified Minkowski fractal antenna is designed and simulated in dual frequency bands (2.4 and 5.8 GHz) for wireless energy harvesting by deep brain stimulation (DBS) devices. The designed antenna, physically being confined inside a miniaturized structure, can efficiently convert the wireless signals in dual ISM frequency bands to the energy source to recharge the DBS battery or power the pulse generator directly. The performance metrics such as the return loss, the specific absorption rate (SAR), and the radiation pattern within skin and muscle-fat-skin tissues are evaluated for the designed antenna. The gain of the proposed antenna is 3.2 dBi at 2.4 GHz and 4.7 dBi at 5.8 GHz; also the averaged SAR of the antenna in human body tissue is found to be well below the legally allowed limit at both frequency bands. The link budget shows the received power at the distance of 25 cm at 2.4 GHz and 5.8 GHz are around 0.4 mW and 0.04 mW, which can empower the DBS implant. The large operational bandwidth, the physical compactness, and the efficiency in wireless signal reception make this antenna suitable in being used in implanted biomedical devices such as DBS pulse generators.

Description: Advancement in wireless sensor network (WSN) technology makes it more attractive technology to be adopted in real world applications including home and industrial automation and e-health or infrastructure monitoring. However the mobility consideration in these applications makes the security requirements an essential and challenging task. To make the communication secure and the network robust against attacks, a proper key management scheme should be used. This paper presents a secure online key establishment and authentication scheme for mobility supported heterogeneous sensor networks. The performance evaluation of the proposed scheme is done using OMNET++ simulator while AVISPA tool is used to validate the security of the proposed scheme. It is clear from the obtained results that the proposed scheme provides better network connectivity at a low cost of memory occupation and communication overhead during the authentication and key establishment phases while improving its network resilience against attacks.

Description: A catalog of high-impact windstorms in Switzerland since 1859 Natural Hazards and Earth System Science, 14, 2867-2882, 2014 Author(s): P. Stucki, S. Brönnimann, O. Martius, C. Welker, M. Imhof, N. von Wattenwyl, and N. Philipp In recent decades, extremely hazardous windstorms have caused enormous losses to buildings, infrastructure and forests in Switzerland. This has increased societal and scientific interest in the intensity and frequency of historical high-impact storms. However, high-resolution wind data and damage statistics mostly span recent decades only. For this study, we collected quantitative (e.g., volumes of windfall timber, losses relating to buildings) and descriptive (e.g., forestry or insurance reports) information on the impact of historical windstorms. To define windstorm severity, normalized and declustered quantitative data were processed by extreme value statistics. Descriptive information was classified using a conceptual guideline. Validation with independent damage information, as well as comparison with wind measurements and a reanalysis, indicates that the most hazardous winter storms are captured, while too few moderate windstorms are detected. Strong storms in the wind measurements and reanalysis are thus added to the catalog. The final catalog encompasses approximately 240 high-impact windstorms in Switzerland since 1859. It features three robust severity classes and contains eight extreme windstorms. Evidence of high winter storm activity in the early and late 20th century compared to the mid-20th century in both damage and wind data indicates a co-variability of hazard and related damage on decadal timescales.

Description: Generalized drought assessment in Dongliao river basin based on water resources system Natural Hazards and Earth System Sciences Discussions, 2, 6703-6746, 2014 Author(s): B. S. Weng, D. H. Yan, H. Wang, T. L. Qin, and J. Yin Drought is firstly a resource issue, and with its development it transforms into a disaster issue. The occurrences of drought events usually feature determinacy and randomness. Drought issue has become one of the major factors to affect sustainable economic and social development. In this paper, we propose the generalized drought assessment index (GDAI) based on water resources system for assessing drought events. The GDAI considers water supply and water demand using a distributed hydrological model. We demonstrate the use of the proposed index in the Dongliao river basin (DRB) in the northeast China. The results simulated by the GDAI are then compared to observed drought disaster records in DRB. As second, the temporal distribution of drought events and the spatial distribution of drought frequency from the GDAI are compared with the traditional approach (i.e. the SPI, the PDSI, and the RWD). Then, generalized drought times (GDT), generalized drought duration (GDD), and generalized drought severity (GDS) were calculated by theory of runs. Application of the GDT, the GDD, and the GDS of various drought levels (i.e. mild drought, moderate drought, severe drought, and extreme drought) to the period 1960–2010 shows that the centers of gravity of them are all distributed in the middle reached of DRB, and change with time. The proposed methodology helps water managers in water-stressed regions to quantify the impact of drought, consequently, to make decisions regarding coping with drought issue.

Description: A GIS-based model to estimate flood consequences and the degree of accessibility and operability of strategic emergency response structures in urban areas Natural Hazards and Earth System Science, 14, 2847-2865, 2014 Author(s): R. Albano, A. Sole, J. Adamowski, and L. Mancusi Efficient decision-making regarding flood risk reduction has become a priority for authorities and stakeholders in many European countries. Risk analysis methods and techniques are a useful tool for evaluating costs and benefits of possible interventions. Within this context, a methodology to estimate flood consequences was developed in this paper that is based on GIS, and integrated with a model that estimates the degree of accessibility and operability of strategic emergency response structures in an urban area. The majority of the currently available approaches do not properly analyse road network connections and dependencies within systems, and as such a loss of roads could cause significant damages and problems to emergency services in cases of flooding. The proposed model is unique in that it provides a maximum-impact estimation of flood consequences on the basis of the operability of the strategic emergency structures in an urban area, their accessibility, and connection within the urban system of a city (i.e. connection between aid centres and buildings at risk), in the emergency phase. The results of a case study in the Puglia region in southern Italy are described to illustrate the practical applications of this newly proposed approach. The main advantage of the proposed approach is that it allows for defining a hierarchy between different infrastructure in the urban area through the identification of particular components whose operation and efficiency are critical for emergency management. This information can be used by decision-makers to prioritize risk reduction interventions in flood emergencies in urban areas, given limited financial resources.

Description: Modeling rapid mass movements using the shallow water equations Natural Hazards and Earth System Sciences Discussions, 2, 6775-6809, 2014 Author(s): S. Hergarten and J. Robl We propose a new method to model rapid mass movements on complex topography using the shallow water equations in Cartesian coordinates. These equations are the widely used standard approximation for the flow of water in rivers and shallow lakes, but the main prerequisite for their application – an almost horizontal fluid table – is in general not satisfied for avalanches and debris flows in steep terrain. Therefore, we have developed appropriate correction terms for large topographic gradients. In this study we present the mathematical formulation of these correction terms and their implementation in the open source flow solver GERRIS. This novel approach is evaluated by simulating avalanches on synthetic and finally natural topographies and the widely used Voellmy flow resistance law. The results are tested against analytical solutions and the commercial avalanche model RAMMS. The overall results are in excellent agreement with the reference system RAMMS, and the deviations between the different models are far below the uncertainties in the determination of the relevant fluid parameters and involved avalanche volumes in reality. As this code is freely available and open source, it can be easily extended by additional fluid models or source areas, making this model suitable for simulating several types of rapid mass movements. It therefore provides a valuable tool assisting regional scale natural hazard studies.

Description: Magnetotelluric investigation in the High Agri Valley (southern Apennine, Italy) Natural Hazards and Earth System Sciences Discussions, 2, 6747-6773, 2014 Author(s): M. Balasco, A. Giocoli, S. Piscitelli, G. Romano, A. Siniscalchi, T. A. Stabile, and S. Tripladi In this paper we present the result of a Magnetotelluric (MT) investigation carried out across the High Agri Valley (HAV), southern Italy. Several MT soundings were carried out in order to obtain a ~15 km long 2-D resistivity model with an investigation depth of ~10 km. The main aim was to provide valuable data on the geological and structural setting of the HAV. The MT model was compared with pre-existing geological, geophysical and seismic data. The MT model can be schematized as a superposition of three stack lateral varying layers with different thickness and resistivity values: a surficial low-medium resistivity layer, associated to the Quaternary deposits and to the allochthonous units, and a deeper high resistivity layer, related to the Apulia Platform, separated by a thin layer connected to the mélange zone and to the Pliocene terrigenous marine deposits. Sharp lateral resistivity variations are interpreted as faults that, on the basis of accurate focal mechanism computations, display normal-faulting kinematics.

Description: Regional parent flood frequency distributions in Europe – Part 2: Climate and scale controls Hydrology and Earth System Sciences, 18, 4391-4401, 2014 Author(s): J. L. Salinas, A. Castellarin, S. Kohnová, and T. R. Kjeldsen This study aims to better understand the effect of catchment scale and climate on the statistical properties of regional flood frequency distributions. A database of L-moment ratios of annual maximum series (AMS) of peak discharges from Austria, Italy and Slovakia, involving a total of 813 catchments with more than 25 yr of record length is presented, together with mean annual precipitation (MAP) and basin area as catchment descriptors surrogates of climate and scale controls. A purely data-based investigation performed on the database shows that the generalized extreme value (GEV) distribution provides a better representation of the averaged sample L-moment ratios compared to the other distributions considered, for catchments with medium to higher values of MAP independently of catchment area, while the three-parameter lognormal distribution is probably a more appropriate choice for drier (lower MAP) intermediate-sized catchments, which presented higher skewness values. Sample L-moment ratios do not follow systematically any of the theoretical two-parameter distributions. In particular, the averaged values of L-coefficient of skewness (L-Cs) are always larger than Gumbel 's fixed L-Cs. The results presented in this paper contribute to the progress in defining a set of "process-driven" pan-European flood frequency distributions and to assess possible effects of environmental change on its properties.

Description: Wind waves in the Black Sea: results of a hindcast study Natural Hazards and Earth System Science, 14, 2883-2897, 2014 Author(s): V. S. Arkhipkin, F. N. Gippius, K. P. Koltermann, and G. V. Surkova In this study we describe the wind wave fields in the Black Sea. The general aims of the work were the estimation of statistical wave parameters and the assessment of interannual and seasonal wave parameter variability. The domain of this study was the entire Black Sea. Wave parameters were calculated by means of the SWAN wave model on a 5 × 5 km rectangular grid. Initial conditions (wind speed and direction) for the period between 1949 and 2010 were derived from the NCEP/NCAR reanalysis. According to our calculations the average significant wave height on the Black Sea does not exceed 0.7 m. Areas of most significant heavy sea are the southwestern and the northeastern parts of the sea as expressed in the spatial distribution of significant wave heights, wave lengths and periods. Besides, long-term annual variations of wave parameters were estimated. Thus, linear trends of the annual total duration of storms and of their quantity are nearly stable over the hindcast period. However, an intensification of storm activity is observed in the 1960s–1970s.

Description: Complexity in processor microarchitecture and the related issues of power density, hot spots and wire delay, are seen to be a major concern for design migration into low nanometer technologies of the future. This paper evaluates the hardware cost of an alternative to register-file organization, the superscalar stack issue array (SSIA). We believe this is the first such reported study using discrete stack elements. Several possible implementations are evaluated, using a 90 nm standard cell library as a reference model, yielding delay data and FO4 metrics. The evaluation, including reference to ASIC layout, RC extraction, and timing simulation, suggests a 4-wide issue rate of at least four Giga-ops/sec at 90 nm and opportunities for twofold future improvement by using more advanced design approaches.

Description: Estimation of three-dimensional crustal movements in the 2011 Tohoku-oki, Japan earthquake from TerraSAR-X intensity images Natural Hazards and Earth System Sciences Discussions, 2, 7383-7408, 2014 Author(s): W. Liu, F. Yamazaki, M. Matsuoka, T. Nonaka, and T. Sasagawa The Tohoku-Oki earthquake on 11 March 2011 caused significant widespread crustal movements. In a previous study, we proposed a method for capturing two-dimensional (2-D) surface displacements from a pair of pre- and post-event TerraSAR-X (TSX) intensity images. However, it is difficult to detect three-dimensional (3-D) displacements from one pair of TSX images. In this study, three pairs of pre- and post-event TSX images taken on different paths were used to estimate 3-D crustal movements. The relationship between the actual 3-D displacements and the converted 2-D movements in the SAR images was derived based on the observation model of a SAR sensor. The 3-D movements were then calculated from three sets of detected 2-D movements that occurred within a short time period. Compared with GPS observations, the proposed method was found to be capable of detecting the 3-D crustal movements with sub-pixel accuracy.

Description: Quantification of hydrologic impacts of climate change in a Mediterranean basin in Sardinia, Italy, through high-resolution simulations Hydrology and Earth System Sciences, 18, 5201-5217, 2014 Author(s): M. Piras, G. Mascaro, R. Deidda, and E. R. Vivoni Future climate projections robustly indicate that the Mediterranean region will experience a significant decrease of mean annual precipitation and an increase in temperature. These changes are expected to seriously affect the hydrologic regime, with a limitation of water availability and an intensification of hydrologic extremes, and to negatively impact local economies. In this study, we quantify the hydrologic impacts of climate change in the Rio Mannu basin (RMB), an agricultural watershed of 472.5 km 2 in Sardinia, Italy. To simulate the wide range of runoff generation mechanisms typical of Mediterranean basins, we adopted a physically based, distributed hydrologic model. The high-resolution forcings in reference and future conditions (30-year records for each period) were provided by four combinations of global and regional climate models, bias-corrected and downscaled in space and time (from ~25 km, 24 h to 5 km, 1 h) through statistical tools. The analysis of the hydrologic model outputs indicates that the RMB is expected to be severely impacted by future climate change. The range of simulations consistently predict (i) a significant diminution of mean annual runoff at the basin outlet, mainly due to a decreasing contribution of the runoff generation mechanisms depending on water available in the soil; (ii) modest variations in mean annual runoff and intensification of mean annual discharge maxima in flatter sub-basins with clay and loamy soils, likely due to a higher occurrence of infiltration excess runoff; (iii) reduction of soil water content and actual evapotranspiration in most areas of the basin; and (iv) a drop in the groundwater table. Results of this study are useful to support the adoption of adaptive strategies for management and planning of agricultural activities and water resources in the region.

Description: Complex networks, streamflow, and hydrometric monitoring system design Hydrology and Earth System Sciences Discussions, 11, 13663-13710, 2014 Author(s): M. Halverson and S. Fleming Network theory is applied to an array of streamflow gauges located in the Coast Mountains of British Columbia and Yukon, Canada. The goal of the analysis is to assess whether insights from this branch of mathematical graph theory can be meaningfully applied to hydrometric data, and more specifically, whether it may help guide decisions concerning stream gauge placement so that the full complexity of the regional hydrology is efficiently captured. The streamflow data, when represented as a complex network, has a global clustering coefficient and average shortest path length consistent with small-world networks, which are a class of stable and efficient networks common in nature, but the results did not clearly suggest a scale-free network. Stability helps ensure that the network is robust to the loss of nodes; in the context of a streamflow network, stability is interpreted as insensitivity to station removal at random. Community structure is also evident in the streamflow network. A community detection algorithm identified 10 separate communities, each of which appears to be defined by the combination of its median seasonal flow regime (pluvial, nival, hybrid, or glacial, which in this region in turn mainly reflects basin elevation) and geographic proximity to other communities (reflecting shared or different daily meteorological forcing). Betweenness analyses additionally suggest a handful of key stations which serve as bridges between communities and might therefore be highly valued. We propose that an idealized sampling network should sample high-betweenness stations, as well as small-membership communities which are by definition rare or undersampled relative to other communities, while retaining some degree of redundancy to maintain network robustness.

Description: Assessing winter cover crop nutrient uptake efficiency using a water quality simulation model Hydrology and Earth System Sciences, 18, 5239-5253, 2014 Author(s): I.-Y. Yeo, S. Lee, A. M. Sadeghi, P. C. Beeson, W. D. Hively, G. W. McCarty, and M. W. Lang Winter cover crops are an effective conservation management practice with potential to improve water quality. Throughout the Chesapeake Bay watershed (CBW), which is located in the mid-Atlantic US, winter cover crop use has been emphasized, and federal and state cost-share programs are available to farmers to subsidize the cost of cover crop establishment. The objective of this study was to assess the long-term effect of planting winter cover crops to improve water quality at the watershed scale (~ 50 km 2 ) and to identify critical source areas of high nitrate export. A physically based watershed simulation model, Soil and Water Assessment Tool (SWAT), was calibrated and validated using water quality monitoring data to simulate hydrological processes and agricultural nutrient cycling over the period of 1990–2000. To accurately simulate winter cover crop biomass in relation to growing conditions, a new approach was developed to further calibrate plant growth parameters that control the leaf area development curve using multitemporal satellite-based measurements of species-specific winter cover crop performance. Multiple SWAT scenarios were developed to obtain baseline information on nitrate loading without winter cover crops and to investigate how nitrate loading could change under different winter cover crop planting scenarios, including different species, planting dates, and implementation areas. The simulation results indicate that winter cover crops have a negligible impact on the water budget but significantly reduce nitrate leaching to groundwater and delivery to the waterways. Without winter cover crops, annual nitrate loading from agricultural lands was approximately 14 kg ha −1 , but decreased to 4.6–10.1 kg ha −1 with cover crops resulting in a reduction rate of 27–67% at the watershed scale. Rye was the most effective species, with a potential to reduce nitrate leaching by up to 93% with early planting at the field scale. Early planting of cover crops (~ 30 days of additional growing days) was crucial, as it lowered nitrate export by an additional ~ 2 kg ha −1 when compared to late planting scenarios. The effectiveness of cover cropping increased with increasing extent of cover crop implementation. Agricultural fields with well-drained soils and those that were more frequently used to grow corn had a higher potential for nitrate leaching and export to the waterways. This study supports the effective implementation of cover crop programs, in part by helping to target critical pollution source areas for cover crop implementation.

Description: Cross-borehole pulse radar has been employed to detect a deeply located empty tunnel. In this paper, effects of underground water collected in the bottom of an empty tunnel on cross-borehole pulse radar signatures are analyzed numerically. B-scan images, stacks of received pulses, are calculated by applying the finite-difference time-domain (FDTD) method for 6 different heights of water from the bottom to the half height inside an empty tunnel. The most important features of an empty tunnel, the fastest time of peak (TOP) and time of arrival (TOA) extracted from the B-scan images, are slowed considerably depending on the increased height of water inside the tunnel. To compensate the weak TOP like that of an empty tunnel, a relation curve is formulated only utilizing measurable parameters of the fastest TOP and the fastest TOA. Then, a unified curve including the effects of two granites with the low and high dielectric properties is derived to cover widely varied dielectric properties of underground rocks. Based on the fastest TOP of an empty tunnel, the average difference between the fastest TOP of an empty tunnel and that of a partially water-filled tunnel decreases from 22.92% to 2.59% after enhancement.

Description: Amalgamation in landslide maps: effects and automatic detection Natural Hazards and Earth System Sciences Discussions, 2, 7651-7678, 2014 Author(s): O. Marc and N. Hovius Inventories of individually delineated landslides are a key to understanding landslide physics and mitigating their impact. They permit assessment of area-frequency distributions and landslide volumes, and testing of statistical correlations between landslides and physical parameters such as topographic gradient or seismic strong motion. Amalgamation, i.e. the mapping of several adjacent landslides as a single polygon, can lead to potentially severe distortion of the statistics of these inventories. This problem can be especially severe in datasets produced by automated mapping. We present 5 inventories of earthquake-induced landslides mapped with different materials and techniques and affected by varying degrees of amalgamation. Errors on the total landslide volume and power-law exponent of the area-frequency distribution, resulting from amalgamation, may be up to 200 and 50%, respectively. We present an algorithm based on image and DEM analysis, for automatic identification of amalgamated polygons. On a set of about 2000 polygons larger than 1000 m 2 , tracing landslides triggered by the 1994 Northridge earthquake, the algorithm performs well, with only 2.7–3.6% wrongly amalgamated landslides missed and 3.9–4.8% correct polygons wrongly identified as amalgams. This algorithm can be used broadly to check landslide inventories and allow faster correction by automating the identification of amalgamation.

Description: Factors affecting flood insurance purchase in residential properties in Johor, Malaysia Natural Hazards and Earth System Science, 14, 3297-3310, 2014 Author(s): U. G. Aliagha, T. E. Jin, W. W. Choong, M. Nadzri Jaafar, and H. M. Ali High-impact floods have become a virtually annual experience in Malaysia, yet flood insurance has remained a grossly neglected part of comprehensive integrated flood risk management. Using discriminant analysis, this study seeks to identify the demand-side variables that best predict flood insurance purchase and risk aversion between two groups of residential homeowners in three districts of Johor State, Malaysia: those who purchased flood insurance and those who did not. Our results revealed an overall 34% purchase rate, with Kota Tinggi district having the highest (44%) and thus the highest degree of flood risk aversion. The Wilks' lambda F test for equality of group means, standardised discriminant function coefficients, structure correlation, and canonical correlation has clearly shown that there are strong significant attribute differences between the two groups of homeowners, based on the measures of objective flood risk exposure, subjective risk perception, and socio-economic cum demographic variables. However, the measures of subjective risk perception were found to be more predictive of flood insurance purchase and flood risk aversion.

Description: Derivation and evaluation of landslide-triggering thresholds by a Monte Carlo approach Hydrology and Earth System Sciences, 18, 4913-4931, 2014 Author(s): D. J. Peres and A. Cancelliere Assessment of landslide-triggering rainfall thresholds is useful for early warning in prone areas. In this paper, it is shown how stochastic rainfall models and hydrological and slope stability physically based models can be advantageously combined in a Monte Carlo simulation framework to generate virtually unlimited-length synthetic rainfall and related slope stability factor of safety data, exploiting the information contained in observed rainfall records and field-measurements of soil hydraulic and geotechnical parameters. The synthetic data set, dichotomized in triggering and non-triggering rainfall events, is analyzed by receiver operating characteristics (ROC) analysis to derive stochastic-input physically based thresholds that optimize the trade-off between correct and wrong predictions. Moreover, the specific modeling framework implemented in this work, based on hourly analysis, enables one to analyze the uncertainty related to variability of rainfall intensity within events and to past rainfall (antecedent rainfall). A specific focus is dedicated to the widely used power-law rainfall intensity–duration ( I – D ) thresholds. Results indicate that variability of intensity during rainfall events influences significantly rainfall intensity and duration associated with landslide triggering. Remarkably, when a time-variable rainfall-rate event is considered, the simulated triggering points may be separated with a very good approximation from the non-triggering ones by a I – D power-law equation, while a representation of rainfall as constant–intensity hyetographs globally leads to non-conservative results. This indicates that the I – D power-law equation is adequate to represent the triggering part due to transient infiltration produced by rainfall events of variable intensity and thus gives a physically based justification for this widely used threshold form, which provides results that are valid when landslide occurrence is mostly due to that part. These conditions are more likely to occur in hillslopes of low specific upslope contributing area, relatively high hydraulic conductivity and high critical wetness ratio. Otherwise, rainfall time history occurring before single rainfall events influences landslide triggering, determining whether a threshold based only on rainfall intensity and duration may be sufficient or it needs to be improved by the introduction of antecedent rainfall variables. Further analyses show that predictability of landslides decreases with soil depth, critical wetness ratio and the increase of vertical basal drainage (leakage) that occurs in the presence of a fractured bedrock.

Description: Climate change and stream temperature projections in the Columbia River basin: habitat implications of spatial variation in hydrologic drivers Hydrology and Earth System Sciences, 18, 4897-4912, 2014 Author(s): D. L. Ficklin, B. L. Barnhart, J. H. Knouft, I. T. Stewart, E. P. Maurer, S. L. Letsinger, and G. W. Whittaker Water temperature is a primary physical factor regulating the persistence and distribution of aquatic taxa. Considering projected increases in air temperature and changes in precipitation in the coming century, accurate assessment of suitable thermal habitats in freshwater systems is critical for predicting aquatic species' responses to changes in climate and for guiding adaptation strategies. We use a hydrologic model coupled with a stream temperature model and downscaled general circulation model outputs to explore the spatially and temporally varying changes in stream temperature for the late 21st century at the subbasin and ecological province scale for the Columbia River basin (CRB). On average, stream temperatures are projected to increase 3.5 °C for the spring, 5.2 °C for the summer, 2.7 °C for the fall, and 1.6 °C for the winter. While results indicate changes in stream temperature are correlated with changes in air temperature, our results also capture the important, and often ignored, influence of hydrological processes on changes in stream temperature. Decreases in future snowcover will result in increased thermal sensitivity within regions that were previously buffered by the cooling effect of flow originating as snowmelt. Other hydrological components, such as precipitation, surface runoff, lateral soil water flow, and groundwater inflow, are negatively correlated to increases in stream temperature depending on the ecological province and season. At the ecological province scale, the largest increase in annual stream temperature was within the Mountain Snake ecological province, which is characterized by migratory coldwater fish species. Stream temperature changes varied seasonally with the largest projected stream temperature increases occurring during the spring and summer for all ecological provinces. Our results indicate that stream temperatures are driven by local processes and ultimately require a physically explicit modeling approach to accurately characterize the habitat regulating the distribution and diversity of aquatic taxa.

Description: Monitoring and modelling of soil–plant interactions: the joint use of ERT, sap flow and Eddy Covariance data to characterize the volume of an orange tree root zone Hydrology and Earth System Sciences Discussions, 11, 13353-13384, 2014 Author(s): G. Cassiani, J. Boaga, D. Vanella, M. T. Perri, and S. Consoli Mass and energy exchanges between soil, plants and atmosphere control a number of key environmental processes involving hydrology, biota and climate. The understanding of these exchanges also play a critical role for practical purposes e.g. in precision agriculture. In this paper we present a methodology based on coupling innovative data collection and models in order to obtain quantitative estimates of the key parameters of such complex flow system. In particular we propose the use of hydro-geophysical monitoring via 4-D Electrical Resistivity Tomography (ERT) in conjunction with measurements of plant transpiration via sap flow and evapotranspiration from Eddy Covariance (EC). This abundance of data is fed to a spatially distributed soil model in order to characterize the distribution of active roots. We conducted experiments in an orange orchard in Eastern Sicily (Italy), characterized by the typical Mediterranean semi-arid climate. The subsoil dynamics, particularly influenced by irrigation and root uptake, were characterized mainly by the ERT setup, consisting of 48 buried electrodes on 4 instrumented micro boreholes (about 1.2 m deep) placed at the corners of a square (about 1.3 m in side) surrounding the orange tree, plus 24 mini-electrodes on the surface spaced 0.1 m on a square grid. During the monitoring, we collected repeated ERT and TDR soil moisture measurements, soil water samples, sap flow measurements from the orange tree and EC data. We conducted a laboratory calibration of the soil electrical properties as a function of moisture content and pore water electrical conductivity. Irrigation, precipitation, sap flow and ET data are available allowing knowledge of the system's long term forcing conditions on the system. This information was used to calibrate a 1-D Richards' equation model representing the dynamics of the volume monitored via 3-D ERT. Information on the soil hydraulic properties was collected from laboratory and field experiments. The successful results of the calibrated modeling exercise allow the quantification of the soil volume interested by root water uptake. This volume is much smaller (with a surface area less than 2 m 2 , and about 40 cm thickness) than expected and assumed in the design of classical drip irrigation schemes that prove to be losing at least half of the irrigated water that is not uptaken by the plants.

Description: A number of commercially available art protection products have been compared and assessed for their suitability as UV blocking filters in the application of “visible light” photocatalytic research. Many groups claiming visible light photocatalytic success employ filters to block out stray UV radiation in order to justify that their photocatalysts are indeed visible light photocatalysts and not UV light photocatalysts. These filters come in varying degrees of ability and price and many authors fail to correctly characterise their filters in individual papers. The use of effective filters to prevent both false positive and false negative results is important to maintain scientific rigor and create accurate understanding of the subject. The optimum UV filter would have the highest UV blocking properties (

Description: This paper investigates a combination of fingerprinting (FP) and extended Kalman filter (EKF) based tracking aiming to tackle conventional problems related to implementation of either tracking or fingerprinting separately. One of the common drawbacks of FP belongs to large data size and consequent large search space. By taking advantage of latest position estimate got from EKF, a virtual surveillance area (VSA) is defined around the estimate. The dimension of this defined surveillance area is much smaller than the size of indoor environment. Consequently, there will be a possibility for FP to be applied in larger areas maintaining the possibility of adding necessary grid points in order to achieve a desired localization performance. Additionally, in order to improve accuracy of ranging, we investigate the impact of a priori knowledge related to the clusters impulse responses and other features; the applied so called soft ranging algorithm for time of arrival (TOA) estimation is modified in order to take advantage of this a priori information and to make its decision variables more accurate. Simulation results show a promising performance improvement via using the proposed hybrid tracking technique and applying a priori information to soft ranging. The tradeoff is along a reasonable increased implementation complexity.

Description: Moraine-dammed lake failures in Patagonia and assessment of outburst susceptibility in the Baker Basin Natural Hazards and Earth System Science, 14, 3243-3259, 2014 Author(s): P. Iribarren Anacona, K.P. Norton, and A. Mackintosh Glacier retreat since the Little Ice Age has resulted in the development or expansion of hundreds of glacial lakes in Patagonia. Some of these lakes have produced large (≥ 10 6 m 3 ) Glacial Lake Outburst Floods (GLOFs) damaging inhabited areas. GLOF hazard studies in Patagonia have been mainly based on the analysis of short-term series (≤ 50 years) of flood data and until now no attempt has been made to identify the relative susceptibility of lakes to failure. Power schemes and associated infrastructure are planned for Patagonian basins that have historically been affected by GLOFs, and we now require a thorough understanding of the characteristics of dangerous lakes in order to assist with hazard assessment and planning. In this paper, the conditioning factors of 16 outbursts from moraine-dammed lakes in Patagonia were analysed. These data were used to develop a classification scheme designed to assess outburst susceptibility, based on image classification techniques, flow routine algorithms and the Analytical Hierarchy Process. This scheme was applied to the Baker Basin, Chile, where at least seven moraine-dammed lakes have failed in historic time. We identified 386 moraine-dammed lakes in the Baker Basin of which 28 were classified with high or very high outburst susceptibility. Commonly, lakes with high outburst susceptibility are in contact with glaciers and have moderate (〉 8°) to steep (〉 15°) dam outlet slopes, akin to failed lakes in Patagonia. The proposed classification scheme is suitable for first-order GLOF hazard assessments in this region. However, rapidly changing glaciers in Patagonia make detailed analysis and monitoring of hazardous lakes and glaciated areas upstream from inhabited areas or critical infrastructure necessary, in order to better prepare for hazards emerging from an evolving cryosphere.

Description: Seismology of the Oso-Steelhead landslide Natural Hazards and Earth System Sciences Discussions, 2, 7309-7327, 2014 Author(s): C. Hibert, C. P. Stark, and G. Ekström We carry out a combined analysis of the short- and long-period seismic signals generated by the devastating Oso-Steelhead landslide that occurred on 22 March 2014. The seismic records show that the Oso-Steelhead landslide was not a single slope failure, but a succession of multiple failures distinguished by two major collapses that occurred approximately three minutes apart. The first generated long-period surface waves that were recorded at several proximal stations. We invert these long-period signals for the forces acting at the source, and obtain estimates of the first failure runout and kinematics, as well as its mass after calibration against the mass-center displacement estimated from remote-sensing imagery. Short-period analysis of both events suggests that the source dynamics of the second are more complex than the first. No distinct long-period surface waves were recorded for the second failure, which prevents inversion for its source parameters. However, by comparing the seismic energy of the short-period waves generated by both events we are able to estimate the volume of the second. Our analysis suggests that the volume of the second failure is about 15–30% of the total landslide volume, which is in agreement with ground observations.

Description: This paper introduces the design and implementation of two high gain Quasi-Yagi printed antennas developed on silicon substrate for 94 GHz imaging applications. The proposed antennas are based on either driven loop or dipole antennas fed by a coplanar waveguide (CPW) feeding structure. For better matching with the driven antennas, a matching section has been added between the CPW feedline and the driven antenna element. To improve the gain of either loop or dipole antennas, a ground reflector and parasitic director elements have been added. Two Quasi-Yagi antenna prototypes based on loop and dipole antenna elements have been fabricated and experimentally tested using W-band probing station (75–110 GHz). The measured results show good agreement with simulated results and confirm that the proposed antennas are working. In addition, a feed and matching configuration is proposed to enable coupling a microbolometer element to the proposed Quasi-Yagi antenna designs for performing radiation pattern measurements.

Description: Mobile wireless sensor networks (MWSNs) comprise a collection of mobile sensor nodes with confined and finite resources. They commonly operate in hostile environments such as battle fields and surveillance zones. Owing to their operating nature, MWSNs are often unattended and generally are not equipped with tamper-resistant tools. With little effort, an adversary may capture the nodes, analyze and replicate them, and surreptitiously insert these replicas at strategic locations within the network. Keeping in view of the above, this paper places an emphasis on this aforementioned attack, known as node replication attack in MWSNs. Specifically, the current state-of-the-art of node replication attack in MWSNs is discussed, where this paper provides a detailed description of various existing detection and prevention mechanisms in literature with an aim to provide better understanding of the factors that need to be considered when designing defence mechanism of node replication attack. A detailed categorization of various detection techniques is provided in the paper with critical discussion on each categorization with respect to its advantages, disadvantages, and various constraints. To conclude the paper, a number of parameters are selected for comparison and analysis of all the existing detection schemes in the literature.

Description: Comparison of aeolian snow transport events and snow mass fluxes between observations and simulations made by the regional climate model MAR in Adélie Land, East Antarctica The Cryosphere Discussions, 8, 6007-6032, 2014 Author(s): A. Trouvilliez, H. Gallée, F. Naaim-Bouvet, C. Genthon, C. Amory, V. Favier, C. Agosta, L. Piard, and H. Bellot The regional climate model MAR including a coupled snow pack/aeolian snow transport parameterisation is compared with aeolian snow mass fluxes at a fine spatial resolution (5 km horizontally and 2 m vertically) and at a fine temporal resolution (30 min) over 1 month in Antarctica. Numerous feedbacks are taken into account in the MAR including the drag partitioning caused by the roughness elements. Wind speed is correctly simulated with a positive value of the Nash test (0.60 and 0.37) but the wind speeds above 10 m s −1 are underestimated. The aeolian snow transport events are correctly reproduced with a good temporal resolution except for the aeolian snow transport events with a particles' maximum height below 1 m. The simulated threshold friction velocity, calculated without snowfall, is overestimated. The simulated aeolian snow mass fluxes between 0 to 2 m have the same variations but are underestimated compared to the second-generation FlowCapt values and so is the simulated relative humidity at 2 m. This underestimation is not entirely due to the underestimation of the simulated wind speed. The MAR underestimates the aeolian snow quantity that pass through the first two meters by a factor ten compared to the second-generation FlowCapt value (13 990 kg m −1 and 151 509 kg m −1 respectively). It will conduct the MAR, with this parametrisation, to underestimate the effect of the aeolian snow transport on the Antarctic surface mass balance.

Description: Influence of weak layer heterogeneity and slab properties on slab tensile failure propensity and avalanche release area The Cryosphere Discussions, 8, 6033-6057, 2014 Author(s): J. Gaume, G. Chambon, N. Eckert, M. Naaim, and J. Schweizer Dry-snow slab avalanches are generally caused by a sequence of fracture processes including failure initiation in a weak snow layer underlying a cohesive slab followed by crack propagation within the weak layer (WL) and tensile fracture through the slab. During past decades, theoretical and experimental work has gradually improved our knowledge of the fracture process in snow. However, our limited understanding of crack propagation and fracture arrest propensity prevents the evaluation of avalanche release sizes and thus impedes hazard assessment. To address this issue, slab tensile failure propensity is examined using a mechanically-based statistical model of the slab–WL system based on the finite element method. This model accounts for WL heterogeneity, stress redistribution by elasticity of the slab and the slab possible tensile failure. Two types of avalanche release are distinguished in the simulations: (1) full-slope release if the heterogeneity is not sufficient to stop crack propagation and to trigger a tensile failure within the slab, (2) partial-slope release if fracture arrest and slab tensile failure occurs due to the WL heterogeneity. The probability of these two release types is presented as a function of the characteristics of WL heterogeneity and of the slab. One of the main outcomes is that, for realistic values of the parameters, the tensile failure propensity is mainly influenced by slab properties. Hard and thick snow slabs are more prone to wide-scale crack propagation and thus lead to larger avalanches (full-slope release). In this case, the avalanche size is mainly influenced by topographical and morphological features such as rocks, trees, slope curvature and the spatial variability of the snow depth as it is often claimed in the literature.

Description: Epic landslide erosion from mountain roads in Yunnan, China – challenges for sustainable development Natural Hazards and Earth System Science, 14, 3093-3104, 2014 Author(s): R. C. Sidle, M. Ghestem, and A. Stokes Expanding systems of mountain roads in developing countries have significantly increased the risk of landslides and sedimentation, and have created vulnerabilities for residents and aquatic resources. We measured landslide erosion along seven road segments in steep terrain in the upper Salween River basin, Yunnan, China and estimated sediment delivery to channels. Landslide erosion rates along the roads ranged from 2780 to 48 235 Mg ha −1 yr −1 , the upper end of this range being the highest rate ever reported along mountain roads. The two roads with the highest landslide erosion (FG1 = 12 966 Mg ha −1 yr −1 ; DXD = 48 235 Mg ha −1 yr −1 ) had some of the highest sediment delivery rates to channels (about 80 and 86%, respectively). Overall, 3 times more landslides occurred along cut slopes compared to fill slopes, but fill slope failures had a combined mass 〉 1.3 times that of cut slope failures. Many small landslides occurred along road cuts, but these were often trapped on the road surface. Given the magnitude of the landslide problem and the lack of attention to this issue, a more sustainable approach for mountain road development is outlined based on an analysis of landslide susceptibility and how thresholds for landslide trigger mechanisms would be modified by road location and different construction techniques.

Description: Evaluation of forest fire models on a large observation database Natural Hazards and Earth System Science, 14, 3077-3091, 2014 Author(s): J. B. Filippi, V. Mallet, and B. Nader This paper presents the evaluation of several fire propagation models using a large set of observed fires. The observation base is composed of 80 Mediterranean fire cases of different sizes, which come with the limited information available in an operational context (burned surface and approximative ignition point). Simulations for all cases are carried out with four different front velocity models. The results are compared with several error scoring methods applied to each of the 320 simulations. All tasks are performed in a fully automated manner, with simulations run as first guesses with no tuning for any of the models or cases. This approach leads to a wide range of simulation performance, including some of the bad simulation results to be expected in an operational context. Disregarding the quality of the input data, it is found that the models can be ranked based on their performance and that the most complex models outperform the more empirical ones. Data and source codes used for this paper are freely available to the community.

Description: Monitoring and prediction in Early Warning Systems (EWS) for rapid mass movements Natural Hazards and Earth System Sciences Discussions, 2, 7149-7179, 2014 Author(s): M. Stähli, M. Sättele, C. Huggel, B. W. McArdell, P. Lehmann, A. Van Herwijnen, A. Berne, M. Schleiss, A. Ferrari, A. Kos, D. Or, and S. M. Springman Rapid mass movements (RMM) pose a substantial risk to people and infrastructure. Reliable and cost-efficient measures have to be taken to reduce this risk. One of these measures includes establishing and advancing the State of Practice in the application of Early Warning Systems (EWS). EWS have been developed during the past decades and are rapidly increasing. In this document, we focus on the technical part of EWS, i.e. the prediction and timely recognition of imminent hazards, as well as on monitoring slopes at risk and released mass movements. Recent innovations in assessing spatial precipitation, as well as monitoring and modelling precursors, the triggering and deformation of RMM offer new opportunities for next-generation EWS. However, technical advancement can only be transferred into more reliable, operational EWS with an intense dialog between scientists, engineers and those in charge of warning. To this end, further experience with new comprehensive prototype systems jointly operated by scientists and practitioners will be essential.

Description: A new approach to mapping permafrost and change incorporating uncertainties in ground conditions and climate projections The Cryosphere, 8, 2177-2194, 2014 Author(s): Y. Zhang, I. Olthof, R. Fraser, and S. A. Wolfe Spatially detailed information on permafrost distribution and change with climate is important for land use planning, infrastructure development, and environmental assessments. However, the required soil and surficial geology maps in the North are coarse, and projected climate scenarios vary widely. Considering these uncertainties, we propose a new approach to mapping permafrost distribution and change by integrating remote sensing data, field measurements, and a process-based model. Land cover types from satellite imagery are used to capture the general land conditions and to improve the resolution of existing permafrost maps. For each land cover type, field observations are used to estimate the probabilities of different ground conditions. A process-based model is used to quantify the evolution of permafrost for each ground condition under three representative climate scenarios (low, medium, and high warming). From the model results, the probability of permafrost occurrence and the most likely permafrost conditions are determined. We apply this approach at 20 m resolution to a large area in Northwest Territories, Canada. Mapped permafrost conditions are in agreement with field observations and other studies. The data requirements, model robustness, and computation time are reasonable, and this approach may serve as a practical means to mapping permafrost and changes at high resolution in other regions.

Description: Results from a full coupling of the HIRHAM regional climate model and the MIKE SHE hydrological model for a Danish catchment Hydrology and Earth System Sciences, 18, 4733-4749, 2014 Author(s): M. A. D. Larsen, J. C. Refsgaard, M. Drews, M. B. Butts, K. H. Jensen, J. H. Christensen, and O. B. Christensen A major challenge in the emerging research field of coupling of existing regional climate models (RCMs) and hydrology/land-surface models is the computational interaction between the models. Here we present results from a full two-way coupling of the HIRHAM RCM over a 4000 km × 2800 km domain at 11 km resolution and the combined MIKE SHE-SWET hydrology and land-surface models over the 2500 km 2 Skjern River catchment. A total of 26 one-year runs were performed to assess the influence of the data transfer interval (DTI) between the two models and the internal HIRHAM model variability of 10 variables. DTI frequencies between 12 and 120 min were assessed, where the computational overhead was found to increase substantially with increasing exchange frequency. In terms of hourly and daily performance statistics the coupled model simulations performed less accurately than the uncoupled simulations, whereas for longer-term cumulative precipitation the opposite was found, especially for more frequent DTI rates. Four of six output variables from HIRHAM, precipitation, relative humidity, wind speed and air temperature, showed statistically significant improvements in root-mean-square error (RMSE) by reducing the DTI. For these four variables, the HIRHAM RMSE variability corresponded to approximately half of the influence from the DTI frequency and the variability resulted in a large spread in simulated precipitation. Conversely, DTI was found to have only a limited impact on the energy fluxes and discharge simulated by MIKE SHE.

Description: Seasonal cycle and long-term trend of solar energy fluxes through Arctic sea ice The Cryosphere, 8, 2219-2233, 2014 Author(s): S. Arndt and M. Nicolaus Arctic sea ice has not only decreased in volume during the last decades, but has also changed in its physical properties towards a thinner and more seasonal ice cover. These changes strongly impact the energy budget, and might affect the ice-associated ecosystems. In this study, we quantify solar shortwave fluxes through sea ice for the entire Arctic during all seasons. To focus on sea-ice-related processes, we exclude fluxes through open water, scaling linearly with sea ice concentration. We present a new parameterization of light transmittance through sea ice for all seasons as a function of variable sea ice properties. The maximum monthly mean solar heat flux under the ice of 30 × 10 5 Jm −2 occurs in June, enough heat to melt 0.3 m of sea ice. Furthermore, our results suggest that 96% of the annual solar heat input through sea ice occurs during only a 4-month period from May to August. Applying the new parameterization to remote sensing and reanalysis data from 1979 to 2011, we find an increase in transmitted light of 1.5% yr −1 for all regions. This corresponds to an increase in potential sea ice bottom melt of 63% over the 33-year study period. Sensitivity studies reveal that the results depend strongly on the timing of melt onset and the correct classification of ice types. Assuming 2 weeks earlier melt onset, the annual transmitted solar radiation to the upper ocean increases by 20%. Continuing the observed transition from a mixed multi-year/first-year sea ice cover to a seasonal ice cover results in an increase in light transmittance by an additional 18%.

Description: Off-axis electron holography can be used to measure the inner potential of a specimen from its reconstructed phase image and is thus a powerful technique for materials scientists. However, abrupt reversals of contrast from white to black may sometimes occur in a digitally reconstructed phase image, which results in inaccurate information. Such phase distortion is mainly due to the digital reconstruction process and weak electron wave amplitude in some areas of the specimen. Therefore, digital image processing can be applied to the reconstruction and restoration of phase images. In this paper, fringe reconnection processing is applied to phase image restoration of a crystal structure image. The disconnection and wrong connection of interference fringes in the hologram that directly cause a 2 phase jump imperfection are correctly reconnected. Experimental results show that the phase distortion is significantly reduced after the processing. The quality of the reconstructed phase image was improved by the removal of imperfections in the final phase.

Description: Diabetes causes oxidative stress, which in turn generates excessive free radicals resulting in cellular damage. Vitamin C is an antioxidant that protects tissues and organs from oxidative stress. The thymus is one of the most important lymphoid organs, which regulates T-lymphocyte proliferation and maturation. The aim of this study is to investigate the protective effects of vitamin C on the thymus of streptozotocin (STZ)-induced diabetic rats. The mitotic activity and cell integrity of thymic lymphocytes were explored. Wistar Albino rats were divided into three groups: control (Group 1), STZ-diabetes (Group 2) and vitamin C-treated STZ-diabetics (Group 3). Rats received a single intraperitoneal injection of 45 mg/kg STZ to induce diabetes. Vitamin C (20 mg/kg) was administered intragastrically. Semithin and ultrathin sections were examined under a light or an electron microscope, respectively. Considerable numbers of mitotic lymphocytes were observed in the thymus of control rats. In the diabetic rats, however, numbers of mitotic lymphocytes decreased to ~57% of controls, and cell division abnormalities were observed. Additionally, diabetic rats showed degeneration in the structure of the thymus including trabecular thickening, accumulation of lipid vacuoles, heterochromatic nuclei and loss of mitochondrial cristae. Degradation of medullar and cortical integrity was also detected. In the vitamin C-treated STZ-diabetic group, the structure of the thymus and mitotic activity of the lymphocytes were similar to the control group. These results suggest that vitamin C protects the thymus against injury caused by diabetes and restores thymocyte mitotic activity.

Description: We investigated the stability of Pd/ZnO polar interfaces formed by internal oxidation of Pd–Zn alloys by using high-resolution transmission electron microscopy, electron energy-loss spectroscopy and convergent-beam electron diffraction. At 1273 K, a $$(111{)}_{\mathrm{Pd}}/(000\overline{2}{)}_{\mathrm{ZnO}}$$ polar interface defaceted and transformed into a curved interface, while another (111) Pd /(0002) ZnO polar interface retained its flatness. The $$(111{)}_{\mathrm{Pd}}/(000\overline{2}{)}_{\mathrm{ZnO}}$$ polar interface lost some stability over non-polar interfaces at 1273 K, while the (111) Pd /(0002) ZnO polar interface remained stable.

Description: Transmission electron microscope (TEM) observation of light metal hydrides is complicated by the instability of these materials under electron irradiation. In this study, the electron kinetic energy dependences of the interactions of incident electrons with lithium, sodium and magnesium hydrides, as well as the constituting element effect on the interactions, were theoretically discussed, and electron irradiation damage to these hydrides was examined using in situ TEM. The results indicate that high incident electron kinetic energy helps alleviate the irradiation damage resulting from inelastic or elastic scattering of the incident electrons in the TEM. Therefore, observations and characterizations of these materials would benefit from increased, instead decreased, TEM operating voltage.

Description: Synaptic plasticity is the process by which long-lasting changes take place at synaptic connections. The phenomenon itself is complex and can involve many levels of organization. Some authors separate forms into adaptations that have positive or negative consequences for the individual. It has been hypothesized that an increase in the number of synapses may represent a structural basis for the enduring expression of synaptic plasticity during some events that involve memory and learning; also, it has been suggested that perforated synapses increase in number after some diseases and experimental situations. The aim of this study was to analyze whether dopamine depletion induces changes in the synaptology of the corpus striatum of rats after the unilateral injection of 6-OHDA. The findings suggest that after the lesion, both contralateral and ipsilateral striata exhibit an increased length of the synaptic ending in ipsilateral (since third day) and contralateral striatum (since Day 20), loss of axospinous synapses in ipsilateral striatum and a significant increment in the number of perforated synapses, suggesting brain plasticity that might be deleterious for the spines, because this type of synaptic contacts are presumably excitatory, and in the absence of the modulatory effects of dopamine, the neuron could die through excitotoxic mechanisms. Thus, we can conclude that the presence of perforated synapses after striatal dopamine depletion might be a form of maladaptive synaptic plasticity.

Description: Unlike in vitro protein dynamics, intracellular protein dynamics are intricately regulated by protein–protein interactions or interactions between proteins and other cellular components, including nucleic acids, the plasma membrane and the cytoskeleton. Alteration of these dynamics plays a crucial role in physiological phenomena such as gene expression and cell division. Live-cell imaging via microscopy with the inherent properties of fluorescent proteins, i.e. photobleaching and photoconversion, or fluorescence correlation spectroscopy, provides insight into the movement of proteins and their interactions with cellular components. This article reviews techniques based on photo-induced changes in the physicochemical properties of fluorescent proteins to measure protein dynamics inside living cells, and it also discusses the strengths and weaknesses of these techniques.

Description: We have developed a method of atomic force microscopy (AFM)-assisted scanning tunneling spectroscopy (STS) under ambient conditions. An AFM function is used for rapid access to a selected position prior to performing STS. The AFM feedback is further used to suppress vertical thermal drift of the tip–sample distance during spectroscopy, enabling flexible and stable spectroscopy measurements at room temperature.

Description: To elucidate high-temperature plastic deformation (creep) mechanism in materials, it is essential to observe dislocation motion under tensile loading. There are many reports on in situ transmission electron microscopy (TEM) observations in the literature; however, the relationship between the dislocation motion and shear stress in 9Cr steel is still not clear. In this study, in order to evaluate this relationship quantitatively, in situ TEM observations were carried out in conjunction with finite element method (FEM) analysis. A tensile test sample was strained at an elevated temperature (903 K) inside a transmission electron microscope, and the stress distribution in the strained sample was analyzed by FEM. The dislocation behavior was clearly found to depend on the shear stress. At a shear stress of 66 MPa, both the dislocation velocity and mobile dislocation density were low. However, a high shear stress level of 95 MPa caused a noticeable increase in the dislocation velocity and mobile dislocation density. Furthermore, in this article, we discuss the dependence of the dislocation behavior on stress. The results presented here also indicate that the relationship between the microstructure and the strength of materials can be revealed by the methods used in this work.

Description: A dual-axis 360° rotation specimen holder was developed for use in reconstructing the three-dimensional (3D) distribution of a magnetic field using a combination of electron holography and tomography. Pillar-shaped specimens are used to obtain accurate reconstruction without a missing angle. The holder's rotation rod can be turned 〉360°; the pillar is set ±45° to the azimuth for both x - and y -axis rotation. Two rotation series of holograms in individual axes are recorded for vector field tomography. The two vector components of the magnetic field are reconstructed directly from the two series of holograms, and the remaining component is calculated using Maxwell's equation, div B = 0. As a result, all 3D magnetic fields are reconstructed.

Description: A new type of electrochemical cell was developed for in situ transmission electron microscopy observation that enables the electrode materials to be conveniently changed. The electrochemical cell was used to observe the electrochemical growth or dissolution of copper islands on a gold film with simultaneous cyclic voltammetry measurements. The copper islands could be explained by three-dimensional growing model.

Description: This paper presents a new concept to realize a multifrequency Oscillator-type active printed monopole antenna. The concept of period doubling route to chaos is exploited to generate the multiple frequencies. The chaotic Colpitts oscillator is integrated with the printed monopole antenna (PMA) on the same side of the substrate to realize an Oscillator-type active antenna where the PMA acts as a load and radiator to the chaotic oscillator. By changing the bias voltage of the oscillator, the antenna can be made to operate at single or multiple frequencies. To test the characteristics of the antenna at single and multiple frequencies of operation, two similar prototype models of printed monopole broadband antennas are developed. One of these antennas used at transmit side is fed by the chaotic Colpitts oscillator while the other is used as the receive antenna. It is observed that the antenna receives single or multiple frequencies simultaneously for particular values of the bias voltage of the oscillator at the transmit end.

Description: Disordered intermolecular interaction carbon nitride precursor prepared by water-assisted grinding of dicyandiamide was used for synthesis of g-C3N4. The final sample possesses much looser structure and provides a broadening optical window for effective light harvesting and charge separation efficiency, which exhibits significantly improved H2 evolution by photocatalytic water splitting. The bottom-up mechanochemistry method opens new vistas towards the potential applications of weak interactions in the photocatalysis field and may also stimulate novel ideas completely different from traditional ones for the design and optimization of photocatalysts.

Description: The railway is one of the most important facilities for freight logistics. This paper suggests the use of the container security devices (CSDs), which has been adopted for the marine transportation so far, to enhance the security of railway freight transportation. The proposed protocol, CSD Chain Network Protocol (CCNP), was designed for a chain-form network of CSDs, each of which is attached to a container. In CCNP, unauthorized access to freight is reliably reported to the reader deployed at the locomotive. CCNP also cares about the fairness in energy consumption. In a usual chain network, a tag closer to the reader consumes more energy since it ought to forward packets coming from rear tags as well. However, in CCNP, the tag energy consumption for packet forwarding is always the same regardless of the position in a chain owing to an efficient data fusion scheme. In our simulation using QualNet, CCNP reduces the number of disconnections between tags by 59.5% as compared to general chain networks. The energy consumption also decreases by 91.3% of other networks not using an aggregation method.

Description: A broadband and high gain tapered slot antenna (TSA) by utilizing a broadband microstrip- (MS-) to-coplanar stripline (CPS) balun has been developed for millimeter-wave imaging systems and sensors. This antenna exhibits ultrawideband performance for frequency ranges from 70 to over 110 GHz with the high antenna gain, low sidelobe levels, and narrow beamwidth. The validity of this antenna as imaging arrays is also demonstrated by analyzing mutual couplings and 4-element linear array. This antenna can be applied to mm-wave phased array, imaging array for plasma diagnostics applications.

Description: Testing gridded land precipitation data and precipitation and runoff reanalyses (1982–2010) between 45° S and 45° N with Normalized Difference Vegetation Index data Hydrology and Earth System Sciences Discussions, 11, 13175-13205, 2014 Author(s): S. O. Los The realistic simulation of key components of the land-surface hydrological cycle – precipitation, runoff, evaporation and transpiration – in general circulation models of the atmosphere is crucial to assess adverse weather impacts on environment and society. Here, gridded precipitation data from observations and precipitation and runoff fields from reanalyses were tested with satellite-derived global vegetation index data for 1982–2010 and latitudes between 45° S and 45° N. Data were obtained from the Climate Research Unit (CRU), the Global Precipitation Climatology Project (GPCP) and Tropical Rainfall Monitoring Mission (TRMM; analysed for 1998–2010 only) and (precipitation and runoff) reanalyses were obtained from the National Centers for Environmental Prediction/National Center for Atmospheric Research (NCEP/NCAR), the European Centre for Medium-Range Weather Forecasts (ECMWF) and the NASA Global Modelling and Assimilation Office (GMAO). Annual land-surface precipitation was converted to annual potential vegetation net primary productivity (NPP) and was compared to mean annual Normalized Difference Vegetation Index data measured by the Advanced Very High Resolution Radiometer (1982–1999) and MODIS (2001–2010). The effect of spatial resolution on the agreement between NPP and NDVI was investigated as well. The CRU and TRMM derived NPP agreed most closely with the NDVI data. The GPCP data showed weaker spatial agreement, largely because of their lower spatial resolution, but similar temporal agreement. MERRA Land and ERA Interim precipitation reanalyses showed similar spatial agreement as the GPCP data and good temporal agreement in semi-arid regions of the Americas, Asia, Australia and southern Africa. The NCEP/NCAR reanalysis showed the lowest spatial agreement which could only in part be explained by its lower spatial resolution. No reanalysis showed realistic interannual precipitation variations for northern tropical Africa. Inclusion of runoff in the NPP prediction resulted only in (marginally) better agreement for the MERRA Land reanalysis and worse agreement for the NCEP/NCAR and ERA Interim reanalyses.

Description: A global dataset of the extent of irrigated land from 1900 to 2005 Hydrology and Earth System Sciences Discussions, 11, 13207-13258, 2014 Author(s): S. Siebert, M. Kummu, M. Porkka, P. Döll, N. Ramankutty, and B. R. Scanlon Irrigation intensifies land use by increasing crop yield but also impacts water resources. It affects water and energy balances and consequently the microclimate in irrigated regions. Therefore, knowledge of the extent of irrigated land is important for hydrological and crop modelling, global change research, and assessments of resource use and management. Information on the historical evolution of irrigated lands is limited. The new global Historical Irrigation Dataset (HID) provides estimates of the temporal development of the area equipped for irrigation (AEI) between 1900 and 2005 at 5 arc-minute resolution. We collected subnational irrigation statistics from various sources and found that the global extent of AEI increased from 63 million ha (Mha) in 1900 to 112 Mha in 1950 and 306 Mha in 2005. We developed eight gridded versions of time series of AEI by combining subnational irrigation statistics with different data sets on the historical extent of cropland and pasture. Different rules were applied to maximize consistency of the gridded products to subnational irrigation statistics or to historical cropland and pasture data sets. The HID reflects very well the spatial patterns of irrigated land in the western United States as shown on historical maps. Mean aridity on irrigated land increased and river discharge decreased from 1900–1950 whereas aridity decreased from 1950–2005. The dataset and its documentation are made available in an open data repository at https://mygeohub.org/publications/8 (doi: 10.13019/M2MW2G ).

Description: The existing coverage hole boundary detection methods cannot detect large-scale coverage hole boundary in wireless sensor network quickly and efficiently. Aiming at this problem, a boundary detection method for large-scale coverage holes in wireless sensor network based on minimum critical threshold constraint is proposed. Firstly, the optimization problem of minimum critical threshold is highlighted, and its formulaic description is constructed according to probabilistic sensing model. On the basis of this, the distributed gradient information is used to approximately solve the optimization problem. After that, local-scale rough boundary detection algorithm incorporating the minimum critical threshold and its iterative thinning algorithm are proposed according to blocking flow theory. The experimental results show that the proposed method has low computational complexity and network overhead when detecting large-scale coverage hole boundary in wireless sensor network.

Description: Debris flows in the Eastern Italian Alps: seasonality and atmospheric circulation patterns Natural Hazards and Earth System Sciences Discussions, 2, 7197-7224, 2014 Author(s): E. I. Nikolopoulos, M. Borga, F. Marra, S. Crema, and L. Marchi The work examines the seasonality and large-scale atmospheric circulation patterns of debris flows in the Trentino-Alto Adige region (Eastern Italian Alps). Analysis is based on classification algorithms applied on a uniquely dense archive of debris flows and hourly rain gauge precipitation series covering the period 2000–2009. Results highlight the seasonal and synoptic forcing patterns linked to debris flows in the study area. Summer and fall season account for 92% of the debris flows in the record, while atmospheric circulation characterized by Zonal West, Mixed and Meridional South, Southeast patterns account for 80%. Both seasonal and circulation patterns exhibit geographical preference. In the case of seasonality, there is a strong north–south separation of summer–fall dominance while spatial distribution of dominant circulation patterns exhibits clustering, with both Zonal West and Mixed prevailing in the northwest and central east part of the region, while the southern part relates to Meridional South, Southeast pattern. Seasonal and synoptic pattern dependence is pronounced also on the debris flow triggering rainfall properties. Examination of rainfall intensity–duration thresholds derived for different data classes (according to season and synoptic pattern) revealed a distinct variability in estimated thresholds. These findings imply a certain control on debris-flow events and can therefore be used to improve existing alert systems.

Description: Climatic signals from 76 shallow firn cores in Dronning Maud Land, East Antarctica The Cryosphere Discussions, 8, 5961-6005, 2014 Author(s): S. Altnau, E. Schlosser, E. Isaksson, and D. Divine The spatial and temporal distribution of surface mass balance (SMB) and δ 18 O were investigated in the first comprehensive study of a set of 76 firn cores retrieved by various expeditions during the past three decades in Dronning Maud Land, East Antarctica. The large number of cores was used to calculate stacked records of SMB and δ 18 O, which considerably increased the signal-to-noise ratio compared to earlier studies and facilitated the detection of climatic signals. Considerable differences between cores from the interior plateau and the coastal cores were found. The δ 18 O of both the plateau and the ice shelf cores exhibit a slight positive trend over the second half of the 20th century. In the corresponding period, the SMB has a negative trend in the ice shelf cores, but increases on the plateau. Comparison with meteorological data from Neumayer Station revealed that for the ice shelf regions atmospheric dynamic effects are more important than thermodynamics, while on the plateau, the temporal variations of SMB and δ 18 O occur mostly in parallel, thus can be explained by thermodynamic effects. The Southern Annular Mode (SAM) exhibits a positive trend since the mid-1960s, which is assumed to lead to a cooling of East Antarctica. This is not confirmed by the firn core data in our data set. Changes in the atmospheric circulation that result in a changed seasonal distribution of precipitation/accumulation could partly explain the observed features in the ice shelf cores.

Description: Post-LIA glacier changes along a latitudinal transect in the Central Italian Alps The Cryosphere, 8, 2235-2252, 2014 Author(s): R. Scotti, F. Brardinoni, and G. B. Crosta The variability of glacier response to atmospheric temperature rise in different topo-climatic settings is still a matter of debate. To address this question in the Central Italian Alps, we compile a post-LIA (Little Ice Age) multitemporal glacier inventory (1860–1954–1990–2003–2007) along a latitudinal transect that originates north of the continental divide in the Livigno Mountains and extends south through the Disgrazia and Orobie ranges, encompassing continental-to-maritime climatic settings. In these sub-regions, we examine the area change of 111 glaciers. Overall, the total glacierized area has declined from 34.1 to 10.1 km 2 , with a substantial increase in the number of small glaciers due to fragmentation. The average annual decrease (AAD) in glacier area has risen by about 1 order of magnitude from 1860–1990 (Livigno: 0.45; Orobie: 0.42; and Disgrazia: 0.39 % a −1 ) to 1990–2007 (Livigno: 3.08; Orobie: 2.44; and Disgrazia: 2.27 % a −1 ). This ranking changes when considering glaciers smaller than 0.5 km 2 only (i.e., we remove the confounding caused by large glaciers in Disgrazia), so that post-1990 AAD follows the latitudinal gradient and Orobie glaciers stand out (Livigno: 4.07; Disgrazia: 3.57; and Orobie: 2.47 % a −1 ). More recent (2007–2013) field-based mass balances in three selected small glaciers confirm post-1990 trends showing the consistently highest retreat in continental Livigno and minimal area loss in maritime Orobie, with Disgrazia displaying transitional behavior. We argue that the recent resilience of glaciers in Orobie is a consequence of their decoupling from synoptic atmospheric temperature trends, a decoupling that arises from the combination of local topographic configuration (i.e., deep, north-facing cirques) and high winter precipitation, which ensures high snow-avalanche supply, as well as high summer shading and sheltering. Our hypothesis is further supported by the lack of correlations between glacier change and glacier attributes in Orobie, as well as by the higher variability in ELA,sub〉0 positioning, post-LIA glacier change, and interannual mass balances, as we move southward along the transect.

Description: High-resolution land surface modeling utilizing remote sensing parameters and the Noah UCM: a case study in the Los Angeles Basin Hydrology and Earth System Sciences, 18, 4791-4806, 2014 Author(s): P. Vahmani and T. S. Hogue In the current work we investigate the utility of remote-sensing-based surface parameters in the Noah UCM (urban canopy model) over a highly developed urban area. Landsat and fused Landsat–MODIS data are utilized to generate high-resolution (30 m) monthly spatial maps of green vegetation fraction (GVF), impervious surface area (ISA), albedo, leaf area index (LAI), and emissivity in the Los Angeles metropolitan area. The gridded remotely sensed parameter data sets are directly substituted for the land-use/lookup-table-based values in the Noah-UCM modeling framework. Model performance in reproducing ET (evapotranspiration) and LST (land surface temperature) fields is evaluated utilizing Landsat-based LST and ET estimates from CIMIS (California Irrigation Management Information System) stations as well as in situ measurements. Our assessment shows that the large deviations between the spatial distributions and seasonal fluctuations of the default and measured parameter sets lead to significant errors in the model predictions of monthly ET fields (RMSE = 22.06 mm month −1 ). Results indicate that implemented satellite-derived parameter maps, particularly GVF, enhance the capability of the Noah UCM to reproduce observed ET patterns over vegetated areas in the urban domains (RMSE = 11.77 mm month −1 ). GVF plays the most significant role in reproducing the observed ET fields, likely due to the interaction with other parameters in the model. Our analysis also shows that remotely sensed GVF and ISA improve the model's capability to predict the LST differences between fully vegetated pixels and highly developed areas.

Description: Aerosol-assisted CVD synthesis, characterisation and gas-sensing application of gold-functionalised tungsten oxide Journal of Sensors and Sensor Systems, 3, 325-330, 2014 Author(s): F. Di Maggio, M. Ling, A. Tsang, J. Covington, J. Saffell, and C. Blackman Tungsten oxide nanoneedles (NNs) functionalised with gold nanoparticles (NPs) have been integrated with alumina gas-sensor platforms using a simple and effective co-deposition method via aerosol-assisted chemical vapour deposition (AACVD) utilising a novel gold precursor, (NH 4 )AuCl 4 . The gas-sensing results show that gold NP functionalisation of tungsten oxide NNs improves the sensitivity of response to ethanol, with sensitivity increasing and response time decreasing with increasing amount of gold.

Description: Objectifying user attention and emotion evoked by relevant perceived product components Journal of Sensors and Sensor Systems, 3, 315-324, 2014 Author(s): R. Schmitt, M. Köhler, J. V. Durá, and J. Diaz-Pineda A company's aim is to develop products that engage user attention and evoke positive emotions. Customers base their emotional evaluation on product components that are relevant for their perception. This paper presents findings of both identifying relevant product components and measuring emotions evoked by relevant perceived product components. To validate results, the comparison with self-reporting methods identifies similarities and differences between explicit expressed and implicit recorded customer requirements. On the one hand, eye tracking is applied to deduce the attention provoked by perceived product components. In order to link the product strategy with product components, the paper presents results considering the fact that the gaze track is affected by current thoughts. (Köhler et al., 2013, 2014a, b; Köhler and Schmitt, 2012) On the other hand, since self-reporting tools are only useful for obtaining information about the conscious part of customers' emotions, there is a need for measurement methods that measure the changes in physiological signals (bio-signals). Arousal is similar to emotional intensity and is related to the galvanic skin response. Positive or negative emotions are defined by the valence that is measured by facial electromyography. Findings are presented that relate changes in bio-signals on the aesthetical design to the global product impression as well as to emotions and, subsequently, linking changes in physiological signals to the evaluation of semantic concepts and design parameters. The presented approach provides conclusions and valid information about products as well as product components that provoke certain emotions and about product components linked to a certain product concept, which could be part of a product strategy. Consequently, hard facts and special design rules for emotional product design can be deduced.

Description: Comprehensive evaluation of water resources security in the Yellow River basin based on a Fuzzy Multi-Attribute Decision Analysis Approach Hydrology and Earth System Sciences Discussions, 11, 371-410, 2014 Author(s): K. K. Liu, C. H. Li, Y. P. Cai, M. Xu, and X. H. Xia In this paper, a Fuzzy Multi-Attribute Decision Analysis Approach (FMADAA) was adopted in water resources security evaluation for the nine provinces in the Yellow River basin in 2006. A numerical approximation system and a modified left-right scoring approach were adopted to cope with the uncertainties in the acquired information. Four multi-attribute decision making methods were implemented in the evaluation model for impact evaluation, including simple weighted addition (SWA), weighted product (WP), cooperative game theory (CGT) and technique for order preference by similarity to ideal solution (TOPSIS) which could be used for helping rank the water resources security in those nine provinces as well as the criteria alternatives. Moreover, several aggregation methods including average ranking procedure, borda and copeland methods were used to integrate the ranking results. The ranking results showed that the water resources security of the entire basin is in critical, insecurity and absolute insecurity state, especially in Shanxi, Inner Mongolia and Ningxia provinces in which water resources were lower than the average quantity in China. Hence, future planning of the Yellow River basin should mainly focus on the improvement of water eco-environment status in the provinces above.

Description: Impact of the Hoa Binh Dam (Vietnam) on water and sediment budgets in the Red River basin and delta Hydrology and Earth System Sciences Discussions, 11, 333-370, 2014 Author(s): D. V. Vu, S. Ouillon, D. T. Tran, and V. C. La The Hoa Binh Dam, located on a tributary of the Red River in Vietnam, has a capacity of 9.45 × 10 9 m 3 and was commissioned in December 1988. Although being important for flood prevention, electricity production, and irrigation in northern Vietnam, the Hoa Binh Dam has also highly influenced the suspended sediment distribution in the lower Red River basin, in the delta and in the coastal zone. Its impact was analysed from 50 yr dataset of water discharge and suspended sediment concentration (1960–2010) and the distribution of water and sediment across the nine mouths of the delta was calculated using the MIKE 11 numerical model before and after the dam settlement. Although water discharge at the delta inlet decreased by only 8.8%, the yearly suspended sediment flux dropped, on average from 119 to 43 × 10 6 t yr −1 at Son Tay near Hanoi, and from 85 to 35 × 10 6 t yr −1 in the river mouths. Water regulation has led to decreased water discharge in the wet season and increased water discharge in the dry season. Suspended sediment discharge proportionally increased in northern and southern estuaries and decreased through the main and central Ba Lat mouth. Tidal pumping, which causes a net sediment flux from the coast to the estuary at low discharge, is high in the northern delta, as a consequence of the high tidal range (up to 4.5 m in spring tide; diurnal tide). The shifts in the dynamic and characteristics of the turbidity maximum zone in the Cam-Bach Dang estuary are probably the cause of the enhanced sediment deposition in the Haiphong harbor. Along the coast, the reduced sedimentation rates are coincident with the lower sediment delivery that has been observed since the impoundment of the Hoa Binh Dam.