ALBERT

Notizen: The decay rate of gamma radiation emitted by a Jamaican mineral spring was measured using portable rate meters. The results of these experiments, supported by auxiliary tests, suggested that the main radioelement causing the radioactivity was radon 222. Fluctuations in the intensity of the radiation were studied in situ. An inverse relation between the intensity and the discharge rate of water was established and the effect of rainfall and of earthquakes was investigated. Some suggestions are made concerning the possible source of radon.

Notizen: The iron ores of the Siegerland-district are found in lodes occurring in schists of Lower Devonian age. In the course of the geophysical exploration for these ores, an attempt was also made to clarify the structure and the tectonics of the substratum of the sedimentary rock formations by seismic reflection measurements from the surface. Reflections were recorded in great numbers from layers of Silurian and Devonian age. The form of the folding of the strata derived therefrom corresponds well with that deduced from geological investigations. Beyond that, correlatable reflections were recorded from horizons down to a depth of nearly 25 000 m. It turned out that the iron ore lodes known from the mine workings occur almost vertically above those places where greater dislocations appear in the deepest substratum, and which geologically could be interpreted as fracture zones. The results so far obtained seem to be indicative of the fact that the tectonics of the deepest substratum and the occurrence of ore deposits are related to each other.

Notizen: Precision calibration tests carried out with a Worden gravimeter in environment conditions as varied as possible have led to the following conclusions. The secular variation curve of the calibration shows that the secular relative variation has been very appreciable in the first year of life of the instrument, precisely of 1.3 × 10−3 in 13 months, while it has been practically zero in the second year. This must be ascribed to the fact that at the beginning of the operations the gravity-meter had just arrived from the factory with its measuring body renewed.On the other side the effect of 24°C of temperature difference between two series of determinations reveals itself in a variation of 0.0022 of the value of the calibration, so that it can be established that the variation of the calibration is I‰ for each 10°C of temperature variation.

Notizen: Due weight must be given to three factors (1) its purpose, (2) the limitations imposed by nature, industry and environment, (3) the effect of errors in auxiliary measurements. Together the last two factors give an estimate of the accuracy which can be achieved. If this is sufficient for the instrument to fulfil its purpose design and construction can proceed. If it is not, a detailed survey of the last two factors is necessary in order to estimate the research effort that will be required when directed into the most effective channels. If the project is considered worth the effort it can proceed. These factors are discussed in relation to a borehole gravimeter. It is shown that the purpose will be served only if the accuracy is comparable with the best surface gravimeters. Borehole versions of some surface instruments are considered and it is concluded that none is suitable without considerable modifications. A successful borehole gravimeter is likely to be a completely new instrument.

Notizen: Recently, quite good determinations of interfaces have been made by means of seismic well surveys. These were carried out for various oil companies in Northwest Germany, especially on salt-domes, and in Southern Germany, and in the area of the Upper Rhine Valley. It was the purpose to determine the configuration and position of salt-flanks and important planes of stratification in the neighbourhood of deep wells, and thus to reduce the risk of expensive wells.For the delineation of the boundary surfaces the method described by Gardner in “Geophysics 1949” was applied.The problems arising and the results obtained are discussed in connection with some interesting examples. From them we see, above all, that a knowledge as precise as possible of the seismic velocities of all media involved in the measurement is very important. A good idea of the general stratification in the area of deep wells seismically surveyed will make possible a rational and adequate planning of the survey program and will facilitate the interpretation.

Notizen: A method is described in which the major part of gravimetric terrain corrections may be estimated by digital computing methods.

Notizen: The electric and magnetic field of a direct-current element, embedded in a space consisting of two halfspaces differing in conductivity and permeability, is given in a form suitable for integration along a cable. From these formulae is obtained the field when one end of a D.C. cable is grounded in a highly conducting, pencilformed ore body, considered as a line electrode with uniform current leakage. Numerical examples are given for a horizontal line electrode. The formulae should be useful as a first approximation to the A.C. case. The validity of this is shortly discussed.

Notizen: An analogy is established between the propagation of an electromagnetic field in a horizontally stratified conductive medium and that of currents in a linear electric network. This analogy will allow us to know in which case measurements executed at the surface of the ground can provide information about the properties of deeper layers. The situation is the same as when one tries, by means of impedance measurements at the input terminals, to know the properties of electric lines or lumped networks.A symmetrical linear network establishes between:Voltages V1 and V2 (respectively at input and output terminals)Currents I1 and I2 (respectively at input and output terminals), the relationship 〈displayedItem type="mathematics" xml:id="mu1" numbered="no"〉〈mediaResource alt="image" href="urn:x-wiley:00168025:GPR77:GPR_77_mu1"/〉 is called the “phase constant” and Z the characteristic impedance The table 〈displayedItem type="mathematics" xml:id="mu2" numbered="no"〉〈mediaResource alt="image" href="urn:x-wiley:00168025:GPR77:GPR_77_mu2"/〉 is called “characteristic matrix”If one then takes the horizontal components of an electromagnetic field, one can compare the voltage V with the horizontal electric field E (in volts m-1) and the current I with the horizontal magnetic field H (in Amp m−1)For plane waves in vacuum, one gets (Schelkunoff) Z=C (velocity of light)A layer whose thickness is D has a phase constant⌈= 2 πD/λ (λ= wavelength)For plane waves in a conductive, non magnetic medium whose conductivity is δ, one gets 〈displayedItem type="mathematics" xml:id="mu3" numbered="no"〉〈mediaResource alt="image" href="urn:x-wiley:00168025:GPR77:GPR_77_mu3"/〉 For the system of waves created by a point-source one expresses the solution, since it is classical, as a sum or integral of different modes. For each of these modes, one can still write a bilinear relationship similar to (1), and calculate Z and ⌈.A generalization of this result is given.Boundary conditions that exist at the surfaces of separation are met by writing the continuity of E and H. This condition exactly corresponds to the fact that there one V and one I at the junctions of various sections of lines, or networks.The characteristic matrix of a cascade of networks-or here that of a horizontally stratified ground– is the product of the matrixes of each network. If, in addition, one knows the end impedance–here the conductivity λn of the last layer, supposed to be infinite–one can compute the input impedance Re of the whole system. In electromagnetic prospecting, it is Re that conditions the observable field.Inversely, if measurements were infinitely accurate, the. knowledge of the surface field would give all the thicknesses D and conductivities δ of intermediate layers, in the same way that impedance measurements at the input terminals of a cable would allow to locate any failure. The imperfection of measurements causes the elements located too far away (from the point of view of wave attenuation) to escape detection.

Notizen: The iron ores of the Siegerland district are found in lodes occurring in schists of Lower Devonian age. These lodes, normally dipping almost perpendicularly, could be traced only by seismic reflection measurements underground, up to distances of approximately 500 m. The geophones were attached to the walls of the galleries. The frequencies of the recorded longitudinal and transverse waves ranged from 200 to 500 c.p.s. By this method a new siderite lode was discovered.

Notizen: Book Reviewed in this article:Lehrbuch der angewandten Geophysik, Teil II, H. Haalck.

Notizen: A series of repeat observations during a period of 5 years reveal a variation with time of the Worden gravimeter No. 142 small dial spring system. A possible change in the gravity difference concerned is ruled out. It is shown that the small dial scale factor has diminished by about 0.25 % within the last two years against about 0.5 % four to five years ago. The ratio of L.D. to S.D. has been analysed and the results obtained show confirmation of the change in the small dial system and prove a consistency in the large dial system.

Notizen: A study is made of the possibility of calculating electric potentials, and therefore of interpreting apparent resistivity measurements, when the ground presents structural conditions more complicated than plane, parallel stratification.For this work a schematic type of structure has been chosen, in which the discontinuity planes for electric resistivity are both parallel and perpendicular to the level of the ground.The problem has been examinated in its general aspect, and then some criteria for the numerical calculation have been indicated.Some calculated examples are presented, relevant to vertical electric soundings accomplished by conventional technique, for particular types of structure.

Notizen: The elastic impulse-from an explosion is propagated through the earth as an expanding shell bounded by the wavefront. This wavefront and its motion are a physical reality while rays or trajectories are much less sharply defined and cannot actually be observed because the wavelengths involved in seismic processes are too long. This means that the visualization and the interpretation of seismic processes can be carried out in a more satisfactory, simple and comprehensible way with wavefronts than with rays.H. R. Thornburgh (1930) introduced the very lucid and simple method of interpreting seismic refraction sections, using Huygen's principle to construct wavefronts from two symmetrical shotpoints by working back from their observed arrival times at the surface. The depths are found first with only a knowledge of the velocities down to the refractor and after that the velocities in the refractor can be determined.The pattern of the two wavefronts at equal time intervals, obtained when carrying out Thornburgh's construction, leads to the very simple, approximative “Plus-Minus” method. The additions of the travel times from two symmetrical shotpoints to-each geophone give the relative depths and their subtractions give the velocities of the refractor. The method extrapolates exact quantities from the refractor boundary up to the surface by the “Plus”- and “Minus” lines. This extrapolation introduces errors that can, more or less, be corrected for. A number of hypothetical cases are presented to give an insight into the applicability and reliability of the “Plus-Minus” method. Its main applications are for fairly shallow refraction investigations and for determining weathering corrections for refraction and reflection work.

Notizen: Major savings for operators of seismic parties have been achieved by the use of prilled ammonium nitrate as a substitute for gelatin dynamite in areas where shot holes are dry. Pound for pound, the prills appear to have the same energy yield as 60% gelatin dynamite, and some improvement of records has been noted where prills are used. Safety problems are less with ammonium nitrate than with dynamite, and the development of efficient field handling techniques prevents the loss of production.

Notizen: Some mathematical inequalities are proved and their relevance to the interpretation of local magnetic and gravity anomalies is discussed. They can be applied to the readings of either a vertical magnetometer or a total field magnetometer or a gravimeter and yield a maximum possible value for the depth below the earth's surface of the top surface of the body producing the anomaly.

Notizen: Master diagrams for electromagnetic responses of nine dipole dipole systems are presented for various depths of a vertical infinitely conducting vein. The YY system gives the minimum anomaly for both the inline and broadside arrays. Among other inline systems, it is difficult to decide the clearcut superiority of one system over the other, whereas the XX system in broadside array gives maximum anomaly.

Notizen: The Laboratory of Geophysics of the University of Arizona was presented with an exploration problem by Falconbridge, Ltd. of Canada. Massive mineralized hemispherical “pods” are in the vicinity of a tuff layer of high conductivity and induced polarization response, covered by large thicknesses of resistive volcanics. The initial approach was to utilize electrolytic tank modeling. The extreme resistivity and IP contrasts proved to be difficult to recreate. Two dimensional modeling was attempted next with conductive paper, using copper and silver paint for anomalous masses. This method also proved inadequate. Finally, mathematical equations were solved which could model any arbitrary anomalous body in any steady state electrical field. Plane waves as well as point current sources producing non-plane waves are possible. Finite difference equations were derived for the non-linear partial differential equations under consideration. The equations were solved using a digital computer. Initially, the boundary conditions had to be satisfied at the boundaries of resistivity changes, severely restricting possible geometric shapes for anomalous bodies. The final and successful solution was to apply numerical techniques to obtain solutions of equations which require only that the relative resistivities through the area be specified. The Falconbridge problem and its solution are analyzed.

Notizen: For the two and three layer cases geo-electrical sounding graphs can be rapidly and accurately evaluated by comparing them with an adequate set of standard model graphs. The variety of model graphs required is reasonably limited and the use of a computer is unnecessary for this type of interpretation.For more than three layers a compilation of model graphs is not possible, because the variety of curves required in practice increases immensely. To evaluate a measured graph under these conditions, a model graph is calculated by computer for an approximately calculated resistivity profile which is determined, for example, by means of the auxiliary point methods. This model graph is then compared with the measured curve, and from the deviation between the curves a new resistivity profile is derived, the model graph of which is calculated for another comparison procedure, etc. This type of interpretation, although exact, is very inconvenient and time-consuming, because there is no simple method by which an improved resistivity profile can be derived from the deviations between a model graph and a measured graph.The aim of this paper is, on the one hand, to give a simple interpretation method, suitable for use during field work, for multi-layer geo-electrical sounding graphs, and, on the other hand, to indicate an automatic evaluation procedure based on these principles, suitable for use by digital computer.This interpretation system is based on the resolution of the kernel function of Stefanescu's integral into partial fractions. The system consists of a calculation method for an arbitrary multi-layer case and a highly accurate approximation method for determining those partial fractions which are important for interpretation. The partial fractions are found by fitting three-layer graphs to a measured curve. Using the roots and coefficients of these partial fractions and simple equations derived from the kernel function of Stefanescu's integral, the thicknesses and resistivities of layers may be directly calculated for successively increasing depths.The system also provides a simple method for the approximative construction of model graphs.

Notizen: The theoretical horizontal resistivity profiles over an outcropping vertical dyke for various parameters-electrode spacing, vein-width and resistivity contrast—with inline alpha, beta and gamma-Wenner electrode systems are described. The resistivity profiles present a most bewildering variety of shapes as compared to those in resistivity soundings. The analysis of type curves suggests suitable electrode configuration for detection of wide, moderately wide, and thin veins. The negative apparent resistivity values on the gamma anomalies for resistive vein over certain vein-widths of higher positive values of resistivity reflection factor contradict the concept of apparent resistivity hitherto held.

Notizen: Il est maintenant courant d'employer l'ordinateur pour interpréter les sondages électriques. Cependant, le problème à résoudre en prospection électrique n'admettant pas une solution unique, le but des traitements automatiques consiste simplement à fournir plusieurs hypothèses qui aident à bâtir une interprétation géologique des mesures géophysiques. C'est, d'ailleurs, ce qu'on recherche aussi par la comparaison visuelle des courbes de terrain avec des abaques précalculés. Mais, tandis que l'interprétation manuelle, pour conduire à des solutions qui respectent les mesures faites sur le terrain, exige un temps très long, le traitement automatique fournit immédiatement des solutions compatibles avec les courbes àétudier.Les procédés employés s'adaptent aux divers besoins de la prospection: ils peuvent traiter aussi bien la station isolée que les profils de sondages électriques. C'est ce qu'on se propose de montrer, à l'aide de quelques exemples tirés d'études récentes.

Notizen: Various experiments are described in designing two-dimensional magnetic interpretation algorithms using computer curve fitting techniques.For a single anomaly the position of the anomaly maximum and the half-width of the anomaly give good initial estimates of the plate position and thickness. A nomogram and formulae for improving these estimates is given. Curves and estimates for the effects of finite depth extent of a plate show the limits, when the lower surface of the plate can be neglected in curve fitting.The combined anomaly of two parallel plates can be separated into partial anomalies with no common points using the horizontal derivative of the anomaly. The changes of the anomaly maxima and changes in anomaly half-widths are studied as a function of plate separation. The position of the maxima and the half-widths can be corrected before applying the one-plate procedure for obtaining initial estimates of plate positions and thicknesses.The performance of standard optimization methods of Powell, Davidon, and Marquardt in improving the values of the plate parameters are compared. The Powell method seems to be the most reliable for both single and multi-plate anomalies. All methods become unacceptably slow when the number of plates is greater than 2 or 3. In these cases feasible interpretation times are obtained using the partial anomalies and sequential parabolic search of the parameter values as tailored specially to the thick plate model.Experiments with three different error norms, the classical least squares, weighted least squares and minimax, show that the first norm gives the best overall performance in automatic interpretation. The behaviour of the classical least squares norm as a function of the plate parameters is also briefly described.

Notizen: The growing awareness of the significance of three-dimensional interpretation of seismic reflection data carries with it a need for better understanding of the role of the velocity configuration in the production of reflection patterns. Modeling the reflection responses of a simple dipping plane reflector through velocity models of various degrees of complexity demonstrates the importance of overlying velocities in determining the reflection pattern.Modeling is accomplished using a raytracing technique which determines total travel time of the normal incidence raypath through an arbitrary iso-velocity layer model.

Notizen: In a previous paper it has been shown that we can relate the transient IP electric field Ep, existing in a rock after a step wave of polarizing current, with the steady-state current density Jss during the current step wave as follows: Ep=ρ'Jss.This relation may be interpreted as a generalized Ohm's law, valid in linear cases, in which ρ’(fictitious resistivity) is defined as the product of the true resistivity ρ with the chargeability m.Supposing Ep=—grad Up and applying the divergence condition div Jss= o, one can, for a layered earth, obtain a general expression for the depolarization potential Up as a solution of Laplace's equation ∇2Up= o.Since the mathematical procedure for the solution of this last equation is identical to that used in resistivity problems, we propose now the introduction of an apparent fictitious resistivity ρ'a (defined as the product of the apparent resistivity ρa with the apparent chargeability ma) as a new parameter for the interpretations of IP soundings carried out over layered structures with a common electrode array.The most general expression of ρ'a as a function of the electrode distance turns out to be mathematically identical to the general expression of ρ'a. Therefore it is possible to interpret a ρ'a field curve using the same standard graphs for resistivity prospecting with the usual method of complete curve matching.In this manner a great deal of work is saved since there is no need to construct proper ma graphs for the interpretation of IP soundings, as it has been done up to now.Finally some field examples are reported.

Notizen: Dipole sounding resistivity measurements over layered earth can be interpreted directly by adapting the procedure given by Koefoed (1968) for Schlumberger system. To carry out the first step of the interpretation leading to the determination of the raised kernel function, partial resistivity functions for the dipole method are derived and given in the form of standard curves. The second step involving the derivation of layering parameters from the kernel being independent of the electrode configurations remains unaltered. The applicability and limitations of the method are discussed.

Notizen: Computations have been made for the effect of ground slope in combination with transmitter coil misorientation on different electromagnetic depth sounding systems and sets of frequency sounding master curves are presented for different angles. The effect of a thin air layer due to the elevation of coils above ground surface has been studied for different systems. Also discussed are the effects due to an error in transmitter-receiver coil separation.

Notizen: Creation of antifiltrational cementation curtains needed to prevent increased seepage from water reservoirs is a rather labour-consuming and costly measure. High cost of such curtains necessitates careful checking of the quality of cementation as well as the strength and stability of the solidified cement which is being formed in the pores and fissures of injected rocks.The traditional methods of control are rather labour-consuming and do not allow observations during process of cementation. The advantage of electrometric observations of cementation curtains lies in the possibility of making measurements on the surface from the moment of pumping slurry into a borehole up to the termination of cement hardening.The laboratory investigations carried out by the authors demonstrate an increase in the specific electrical resistivity of a cement in the course of hardening as well as the existence of a functional dependence between the electrical and strength parameters which allows to use the resistivity method for checking the cement strength.Methods of electrometric observations of cementation curtains are dependent on the particular features of cementation and the curtain dimensions. The observations are usually conducted in a network of profiles parallel to the curtain axis. The cement slurry spreading in the space is studied on the maps of ρa and geoelectrical sections obtained at different distances from the feed line. Zones of the strongest absorption of cement slurry are indicated by resistivity minima. The electrometric observations should be compared with the data on cement expenditure in the boreholes.The cement strengthening is monitored by comparing the results of control observations consecutively conducted in 1-2 months following the cementation, with utilization of the ρa maps and graphs. If the specific resistivities of the skeleton of the enclosing rocks and the filler of cavities are known, one can approximately evaluate the changes in the cement strength in absolute units (kg/cm2).By way of example, the authors give the results of electrometric observations conducted to evaluate the quality of an antifiltrational curtain on one of the high-mountain water reservoirs in Armenia.

Notizen: The paper presents the method and algorithm for computing the time-distance curve for head waves in the case of a dipping refractor and velocity increasing with depth in the overburden. The method is illustrated by an example.

Notizen: A new logging method, which makes use of specific chemical reactions to locate petroleum or other minerals has been developed. The method has been named “Differential Electric Log” (CED).In this paper the application to the CED method of redox (reduction/oxidation) reactions is discussed. A series of organic oxidants was found, capable of undergoing reaction with crude oil, sulphur, mineral sulphides, lignite. A small amount of an oxidant of this type is added to the drilling fluid and pumped into the borehole where reaction takes place in correspondence with layers containing oxidizable minerals. Two SP logs, recorded before and after the oxidation, are compared and the presence of such minerals is thus detected.A theoretical hypothesis explaining the mechanism of the potential change due to the chemical reaction is proposed both in the case of electronically conducting and non conducting minerals. The influence of redox potential on SP is discussed.The results of laboratory experiments on several different oxidizable ores and those of field tests performed on pyrite, lignite, and oil wells are reported on and discussed on the basis of the theoretical hypothesis proposed.

Notizen: On an experimental basis, observations were made with various geophysical methods to locate the ancient gold workings in Kolar Gold Fields, Kolar, India. The results of experimental surveys indicated that two-electrode resistivity surveys with two spacings followed by limited trenching would be able to locate about 70 percent of the ancient workings, at 55-60 percent of the cost of conventional trenching.

Notizen: There are different types of acoustic noise induced in streamer cables. One type consists of pulsed waves preferentially generated by vertical motions of the towing ship or of the tail buoy. The pulsed waves travel along the streamer with low attenuation and a velocity about 15% less than the velocity of water. Frequencies observed lie between 5 and 15 Hz.These pulsed waves are well known and for the last few years acoustic isolator sections have been used to reduce their generation. But under bad weather conditions and especially in cold water these waves become stronger. Recent investigations demonstrated that the pulsed waves are able to produce a high noise level even in new streamers with acceleration cancelling hydrophones. We point out that the material of the hoses has a dominant effect on the amplitude picked up by the hydrophones.Acoustic theory is applied to understand the phenomenon of these waves.

Notizen: To specify intelligently a nondynamite source in a marine seismic data-collection system, it is important to use all known parameters of the system—source, receiver, and recording-system characteristics. A technique has been developed to design the far-field pressure pulse of an air-gun array by taking these parameters into account.Important source variables to consider are interaction among guns in the array and the depth of the array. Near-field pressure signatures of individual guns, which are relatively unaffected by boundaries, have been used to‘construct’the far-field pressure pulse of the array by considering these variables. Comparison between constructed pulses and measured far-field pulses shows substantial agreement.Streamer depth and recording-system bandpass should also be considered when designing an air-gun array. Comparison of far-field pressure pulses for several bandpasses clearly shows the importance of considering this variable; e.g., the initial pulse is severely attenuated when a high-cut filter is used. Likewise, an additional filtering effect due to the streamer's proximity to the surface should be taken into account.Design of an air-gun array using the principles just outlined are illustrated by an example.

Notizen: Many practical energy sources are available for land use and likewise a goodly number for marine operations. However, the transitional region between navigable water and negotiable land is poorly served. The vehicles that are capable of operating amphibiously are limited in the pay-load they can transport, and in the bulk of apparatus that can be operated from the space available. The Flex-O-Gun (Trademark of Geo Space Corporation) is a new, lightweight gas exploder designed to meet the requirements for operation in rivers, bays, and marsh areas not generally accessible to the larger, heavier systems such as the Dinoseis (Trademark of Atlantic Richfield Company), Vibrator and Air Guns. Weighing less than 70 kilograms, the Flex-O-Gun requires only modest sources of oxygen and propane and the associated firing equipment for operation.The gun delivers energy by the sudden introduction into the water of high pressure gases resulting from detonation. The device is unique in that the underwater gun assembly contains no gas mixing or firing elements. A flexible, metallic hose conveys the charge of mixed gases and subsequent detonating flame to the gun from control and firing mechanisms located above the surface. With its small weight and total space requirements, the Flex-O-Gun can be operated from small boats, buggies, or trucks, and is easily transported.In this paper the features of the gun are described and the results given of tests of its operations. An implanting device is also discussed which extends its application to viscous formations. The device employs water jets mounted below the gun to wash down a hole and insure placement of the gun at depths to obtain maximum energy output.

Notizen: Five test profiles in time-domain induced polarization measurements over conducting sulphide and graphite mineralisations were run with the two-electrode, three-electrode, modified unipole, pole-dipole, dipole-dipole, Schlumberger, and Wenner α and β configurations. The results show that, compared to the other electrode systems, the simplest two-electrode array produces the largest anomalies with the smallest of spacings.

Notizen: The theoretical horizontal resistivity profiles Over an outcropping vertical dyke with two-electrode and Schlumberger electrode systems are discussed. The two-electrode array seems very useful in locating the highly conducting thick or thin vein, while the Schlumberger (gradient) array is suited to detect the conducting vein of low and moderately high resistivity contrast and as well as the resistive vein of all widths and resistivity contrasts. Besides, the inline gradient array has a distinction of establishing a clue to evaluate the resistivity contrast of the vein.

Notizen: The generalised three layer boundary value problem with a transition layer sand-witched between an isotropic overburden and dipping anisotropic substratum is discussed assuming that plane electro-magnetic waves are incident normally over the air-earth inter-face. The tangential electric (Ey) and magnetic (Hx) fields and the expression for surface-impedance (Ey/Hx) have been evaluated at the earth's surface. Through numerical analysis it is shown that changes in the values of the parameters m (coefficient of anisotropy), h (thickness of the transition layer), α (angle of inclination of the dipping beds), and b (conductivity ratio between substratum and upper layer) modify the amplitude and phase-variation curves (with skindepth) significantly.

Notizen: Gravity modeling involves the evaluation of gravity field due to bodies of irregular shape. This is commonly accomplished by dividing the body into smaller units of regular shape whose field can be determined analytically.Cubes are ideal building blocks for constructing bodies of irregular shape. However, the exact expression defining the gravity field of a cube-shaped body is very long and requires tedious numerical work. Approximation formulas for rapid evaluation of the cube's gravity field are presented and discussed in detail. Their use for computing the field for small distances leads to large errors in the results; on the other hand, using the exact formula for large distances where approximation formulas yield practically identical results, is waste of time. After a detailed analysis about the nature of the cube's gravity field, certain criteria are established for suitably combining the two alternatives. This results in tremendous reduction in the task of computations without affecting the accuracy of data.

Notizen: A rigorous proof is presented to show that over a horizontally layered ground the rms velocity cannot exceed the stacking velocity. The proof helps to illustrate the difference between stacking and rms velocities in a quantitative manner. The series of Taner and Koehler (1969) is used for the purpose. Convergence of this series is tested. Including more terms will not necessarily improve the convergence. Although the series is rapidly convergent when the spread length/depth ratio is small, strong oscillations are observed when this ratio is high.

Notizen: The properties of cross-correlation functions for the case of gravity and magnetic total field anomalies produced by three geometric models of geological bodies (point-mass, horizontal line-mass, and vertical semi-infinite rectangular prism mass distributions) are studied. This study is carried out on four cases of cross-correlation: the whole curve of anomalies, a single branch of anomalies, the branch between the two inflexion points and the branch between the apex point and the inflexion point. In all cases, the crosscorrelation function can serve as a good indicator to discriminate the so-called genetically related anomalies from those produced by different geological bodies situated on the same vertical line; but the best results are obtained using the cross-correlation of the branches between the apex point and the inflexion point of the two geophysical anomalies.A practical procedure is developed in order to undertake such analysis. The tests in some cases of real gravity and magnetic anomalies mapped in Romania show the validity of this practical procedure.

Notizen: The time-honoured method of attenuating coherent noise in the seismic record is by the use of source and geophone arrays. In theory, and using methods familiar in the synthesis of digital frequency filters, arrays can be designed having virtually any desired response in the wavenumber spectrum.In practice, arrays cannot be implemented with the same precision that is applied in design. The response actually achieved must be compromized by a number of factors. These include inaccuracies in the effectiveness or positioning of individual array elements, variations in ground coupling, and the effect of local heterogenities in the environment of the array. We have no reliable way of knowing how well a particular array will perform from one location to the next.Statistical modelling methods have been applied to examine the effects of implementation errors. Experimental results, supported by statistical theory, show that errors are expected to impose a limit upon the rejection capabilities of an array. The expected limiting value of attenuation due to errors in element weights is inversely proportional to the standard deviation of errors and directly proportional to the square root of the number of array elements. Position errors exert a limiting influence which is wavenumber dependent such that attenuation decreases with increasing wavenumber. For arrays of common dimensions, Gaussian random errors of 10% standard deviation in element weights and positions result in an expected attenuation limit of about 30 dB.It follows that the more ambitious array designs are less tolerant of errors, and must be implemented with greater care and precision in the field. The present work enables us to specify tolerances for any particular array design.Ultimately, the degree of pattern refinement which may be effectively employed in any area is determined by errors which are associated with the array environment. Complex arrays are expensive to operate. In order to avoid over-design it would be useful to establish the magnitude of errors to be expected under different terrain conditions.

Notizen: Anisotropy measurements were carried out in two wells 300 km apart in the Northern Sahara, in order to improve the interpretation of seismic refraction surveys.These measurements were based on; the shortening of experimental oblique travel-times with respect to theoretical, travel-times computed by disregarding anisotropy. A perfect knowledge of the velocity distribution is required in order to eliminate all influence of refraction; therefore a continuous velocity log is indispensable.The results in the two wells are in agreement, and show that anisotropy is essentially a function of lithology. The following values were obtained: 〈displayedItem type="mathematics" xml:id="mu1" numbered="no"〉〈mediaResource alt="image" href="urn:x-wiley:00168025:GPR202:GPR_202_mu1"/〉 Consequences pertaining to seismic refraction are as follows:— Depths computed without anisotropy are too small by 8 % to 9 %, i.e. about 300 meters.— The error on offsets reaches 70 %.— Depth computations carried out by assigning anisotropy factors at the sight of lithology gave very satisfactory results.— High velocity, highly anisotropic formations such as anhydrite play a very important part in the propagation of refracted waves and in interpretation.Consequences pertaining to seismic reflection are as follows:— Velocity profiles yield velocities closer to horizontal velocities than to vertical velocities.— Depth and migration computations are significantly influenced by high velocity, highly anisotropic formations such as anhydrite.

Notizen: Book Reviewed in this article:Handbuch der Physik. Herausgegeben von S. Flügge.Der geologische Bau des Untergrundes von Schleswig-Holstein und seine Erdöllager-stätten.

Notizen: Conventional or continuous velocity logging generally fail to solve the problem of velocities in the whole area of a seismic survey. Surface measurements often bring a large amount of additional information: effect of shallow layers, change of facies, correlations. The authors present a theoretical view on the physical meaning of interval velocities. After a short synthesis of the diverse formulae formerly proposed (Faust, West), the practical manner of using these formulae and the accurate interpretation obtained with the help of geological and geophysical data are shown. Several characteristical examples are finally explained and commented on.

Notizen: A uniform field of the normal geomagnetic vertical intensity and its normal dependence on the first and second powers of latitude and longitude are derived for Europe and represented by sketches. The epochs of 1938.5, 1941.5, 1944.5, 1947.5, 1950.5, 1953.5, and 1956.5 have been chosen.It is suggested that anomalies of the vertical intensity should be given according to this field in order to obtain, in course of time, a coherent image of the magnetic effects of the European continent.

Notizen: Solutions for the propagation of elastic waves at the surface of a cylindrical hole of infinite length are derived from the wave equation for a perfectly elastic and isotropic medium. It is found that the phase and group velocities depend on the ratio between the wave length and the circumference of the cylindrical hole. These surface waves can be classified into different orders. They differ in the calculated dispersion curves, in the range of possible wave lengths (cut-off-frequencies), and in the amplitude proportion of the components of the displacement vector. For very short wave lengths these waves converge to normal Rayleigh waves.These results are used to explain some of the multiple onsets and disturbances on seismograms, obtained in practical seismic investigations in the mines of Siegerland.The conformity of theoretical and practical results is limited, because the idealised suppositions on which the computation is based, such as perfect elasticity, homogeneous and isotropic medium, and circular cross section of the mine gallery are met only approximately in practice.

Notizen: During the last ten years data processing has enabled the geophysicist to seriously attack the problem of how to improve the quality of seismic sections. For instance new processing methods have been proposed for improving the resolving power of the seismic pulse. These methods are based on deconvolution and they require lengthy computations.The method discussed here for pulse contraction is based on the use of Hadamard transforms. It is very fast but nevertheless the quality of the result stands comparison with that of conventional methods.

Notizen: Application of statistical methods of analysis of geophysical data is often helpful for the detection of weak anomalies against a noisy background. The processing and analysis of areal geophysical data by two such methods are presented. The advantage of these methods are illustrated with the help of two field examples.

Notizen: The paper deals with the electro-filtrational fields formed near the drainage structures. Main laws of deformation of these fields above vertical and horizontal drains are considered and practical examples supplied.

Notizen: A seismic trace recorded with suitable gain control can be treated as a stationary time series. Each trace, χj(t), from a set of traces, can be broken down into two stationary components: a signal sequence, αj(t) *s(t—τj), which correlates from trace to trace, and an incoherent noise sequence, nj(t), which does not correlate from trace to trace. The model for a seismic trace used in this paper is thus χj(t) =αj(t) * s(t—τj) +nj(t) where the signal wavelet αj(t), the lag (moveout) of the signal τj, and the noise sequence nj(t) can vary in any manner from trace to trace. Given this model, a method for estimating the power spectra of the signal and incoherent noise components on each trace is presented.The method requires the calculation of the multiple coherence function γj(f) of each trace. γj(f) is the fraction of the power on traced at frequency f that can be predicted in a least-square error sense from all other traces. It is related to the signal-to-noise power ratio ρj(f) by 〈displayedItem type="mathematics" xml:id="mu1" numbered="no"〉〈mediaResource alt="image" href="urn:x-wiley:00168025:GPR660:GPR_660_mu1"/〉 where Kj(f) can be computed and is in general close to 1.0. The theory leading to this relation is given in an Appendix.Particular attention is paid to the statistical distributions of all estimated quantities. The statistical behaviour of cross-spectral and coherence estimates is complicated by the presence of bias as well as random deviations. Straightforward methods for removing this bias and setting up confidence limits, based on the principle of maximum likelihood and the Goodman distribution for the sample multiple coherence, are described.Actual field records differ from the assumed model mainly in having more than one correctable component, components other than the required sequence of reflections being lumped together as correlated noise. When more than one correlatable component is present, the estimate for the signal power spectrum obtained by the multiple coherence method is approximately the sum of the power spectra of the correlatable components. A further practical drawback to estimating spectra from seismic data is the limited number of degrees of freedom available. Usually at least one second of stationary data on each trace is needed to estimate the signal spectrum with an accuracy of about 10%. Examples using synthetic data are presented to illustrate the method.

Notizen: Seismic refraction at sea and on continental shelves requires most of all a precise positioning of the shooting and receiving stations and a good signal to noise ratio.A new system has been developed using detectors anchored on the sea floor and radio transmission of signal for refraction work on continental shelves. This technique satisfies both requirements. The system has been tested in the western Channel in December 1971.

Notizen: The problem of interpretation of geoelectrical resistivity soundings has been studied and a compromise method of interpretation developed. A simple depth sequence of increasing bed thickness is taken and resistivities assigned to the various layers so that a good fit is obtained to the observed apparent resistivity curve. An initial estimate of the resistivities is made by a direct method but the model is then altered to give an improved fit by the indirect method of curve matching. The whole method is computerized and input data to the computer program consists of spacings and apparent resistivities. The method is extremely rapid, about one third of the computation time is devoted to obtaining the resistivity transform by the method of convolution. A normal type of solution, incorporating additional information if necessary, can also be obtained.

Notizen: The use of arctangents rather than arcsines in the expression for the gravitational attraction of a homogeneous rectangular prism reduces computational difficulties. Once a subroutine is available to compute one component of attraction in a Cartesian coordinate system, the other components may be obtained by cyclic permutation of the field point and body coordinate parameters. This technique also readily provides derivatives of the gravitational attraction and hence forms a compact method for the calculation of a magnetic anomaly due to a homogeneous rectangular magnetic prism.

Notizen: With the help of the principle of superposition the Input response of a conducting infinite horizontal homogeneous cylinder is synthesised from its step-function response. The variation of transient peaks and the time lag between the secondary and primary fields with the cylinder constitution parameter are illustrated.

Notizen: The new process of automatic determination of seismic velocities by well to well measurements (Bois et al., 1971, Geophysical Prospecting 19, 42-73) gives the possibility to increase the knowledge of oil reservoirs, by detecting large inhomogeneities between wells. It can also give useful informations on the mechanical properties of rocks in mining exploitation and civil engineering, by gallery to gallery measurements. An application of the method is given to the search for the proper location of an underground hydroelectric power plant, where the problem was to investigate the rock properties in a horizontal plane between two exploration galleries.