ALBERT

Description: Comparison of transition locations for an open-nose cone, a conventional sharp cone, and a hollow cylinder showed that transition locations on the open-nose cone and the hollow cylinder were identical but differed greatly from those on the sharp cone. This is believed to be caused by the essentially two-dimensional character of leading edge of the open-nose cone. Bluntness effects on the open-nose cone observed on the hollow cylinder. Transition 2.2 times the sharp-cone transition distance by blunting the tip.

Description: An investigation has been made at Mach numbers of 1.61 and 2.01 and Reynolds numbers from 1.7 X 10 to 7.6 X 10 to determine the pressure distributions over a 60 deg. delta wing having 20 different control configurations. Measurements were made at angles of attack from O deg to 15 deg for control deflections from -30 deg to 30 deg. This report presents the complete tabulated pressure data for the range of test conditions.

Description: An all-internal conical compression inlet with annular bleed at the throat was investigated at Mach 5.0 and zero angle of attack. The minimum contraction ratio of the supersonic diffuser, coincident with a mass-flow ratio of 1.0, was determined to be 0.084 as compared with the isentropic contraction ratio of 0.04 at Mach 5.0. The over-all inlet performance was very sensitive to the amount of annular bleed at the throat because of the extensive boundary layer. For example, the critical recovery varied from 41 percent with 6-percent bleed to 59 percent with 25-percent bleed. Decreasing the spacing between the supersonic and subsonic diffusers increased the critical mass-flow ratio but reduced the range of subcritical mass-flow regulation. A constant-area section was required ahead of the subsonic diffuser in order to obtain reasonable performance. An inlet-engine net-thrust analysis indicated that the optimum performance occurred with from 20- to 25-percent bleed, depending on how the bypassed air was handled.

Description: A supplementary investigation has been conducted in the langley 20-foot free-spinning tunnel on a l/24-scale model of the Grumman F11F-1 airplane to determine the spin and recovery characteristics with alternate nose configurations, the production version and the elongated APS-67 version, with and without empty and full wing tanks. When spins were obtained with either alternate nose configuration, they were oscillatory and recovery characteristics were considered unsatisfactory on the basis of the fact that very slow recoveries were indicated to be possible. The simultaneous extension of canards near the nose of the model with rudder reversal was effective in rapidly terminating the spin. The addition of empty wing tanks had little effect on the developed spin and recovery characteristics. The model did not spin erect with full wing tanks. For optimum recovery from inverted spins, the rudder should be reversed to 22O against the spin and simultaneously the flaperons should be moved with the developed spin; the stick should be held at or moved to full forward longitudinally. The minimum size parachute required to insure satisfactory recoveries in an emergency was found to be 12 feet in diameter (laid out flat) with a drag coefficient of 0.64 (based on the laid-out-flat diameter) and a towline length of 32 feet.

Description: Incipient spin characteristics have been investigated on a l/35-scale dynamic model of the Convair F-10% airplane. The model was launched by a catapult apparatus into free flight with various control settings, and the motions obtained were photographed. The model was ballasted for the combat loading. All tests were made with the speed brakes and landing gear retracted, and engine effects were not simulated. The results of the investigation indicated that the model would enter motions apparently simulating entry phases of spins when the elevators were deflected full up. Deflecting the rudder had little effect on the direction of the motion obtained, but when ailerons were deflected the model always rotated in a direction opposite to the aileron setting (that is, the model entered a right spin with the stick to the left). The ailerons were very influential in initiating spin entry, and the pilot should avoid, as far as possible, the use of ailerons in low-speed flight.

Description: Tests have been made in the Langley 4- by 4-foot supersonic pressure tunnel at Mach numbers of 1.41, 1.61, and 2.01 to determine the static longitudinal stability and control characteristics of various arrangements of the Grumman F11F-1 airplane. Tests were made of the complete model and various combinations of its component parts and, in addition, the effects of various body modifications, a revised vertical tail, and wing fences on the longitudinal characteristics were determined. The results indicate that for a horizontal-tail incidence of -10 deg the trim lift coefficient varied from 0.29 at a Mach number of 1.61 to 0.23 at a Mach number of 2.01 with a corresponding decrease in lift-drag trim from 3.72 to 3.15. Stick-position instability was indicated in the low-supersonic-speed range. A photographic-type nose modification resulted in slightly higher values of minimum drag coefficient but did not significantly affect the static stability or lift-curve slope. The minimum drag coefficient for the complete model with the production nose remained essentially constant at 0.047 throughout the Mach number range investigated.

Description: An investigation has been made in the Langley 8-foot transonic tunnels on the aerodynamic characteristics of a 0.15-scale model of the North American Aviation 255-inch fin-stabilized external store over a maximum Mach number range of 0.60 to 1.2 and on the effects of mounting lugs, of fin orientation, of fin aspect ratio, and of fixed-transition. The Reynolds number (based on a body length of 37.50 inches) varied from 9.8 x 10(exp 6) to 13.1 x 10(exp 6). The results indicate that the static margin of the finned store at low lift coefficients was only 9 percent of body length at subsonic Mach numbers and was reduced to zero at a Mach number of 1.0, Increasing the fin aspect ratio from 1.82 to 2.41 increased the subsonic static margin to 18 percent and provided a minimum margin of 9 percent near a Mach number of l.O. Store mounting lugs or fin orientation had only small effects on the aerodynamic characteristics of the basic store.

Description: An investigation has been made in the Langley Unitary Plan wind tunnel at Mach numbers of 1.60, 1.80, and 2.00 to determine the aerodynamic characteristics of a 0.03-scale model of the Avro CF-105 airplane. The investigation included the determination of the static longitudinal and lateral stability, the control and the hinge-moment characteristics of the elevator, rudder, and aileron, as well as the vertical-tail-load characteristics. Although the data are presented without analysis, a limited inspection of the longitudinal control results indicates a loss in maximum lift-drag ratio due to trimming of about 1.8 because of the large static margin. A reduction in static margin would be expected to improve the trim lift-drag ratio but would also reduce the directional stability. With the existing static margin, the configuration is directionally unstable at angles of attack above about 6 deg or 8 deg.

Description: Operation of the original engine configuration disclosed a severe compressor stall problem at high altitude, which was largely attributed to a radial flow distortion entering the high-pressure compressor. Engine modifications for eliminating or alleviating the stall problem were investigated. These included use of variable high-pressure compressor inlet guide vanes, increased turbine-stator areas, and minor alterations in both the low- and high-pressure compressor rotors.

Description: This paper presents the results of an investigation of sting-support interference on afterbody drag at transonic speeds. Stings with varying diameter, cone angle, and cylindrical length were tested at the rea r of a model with various afterbody shapes. The data were obtained at an angle of attack of O deg. and at Mach numbers from 0.80 to 1.10. It was found that, in general, the addition of a sting caused a drag reduction. A method is presented whereby approximate sting-interferen ce corrections may be made to models with afterbodies and sting suppo rts of similar size and scale to those of this paper provided the bou ndary layer is turbulent at the model base and the Reynolds numbers a re of the same order of magnitude. Reynolds number of the tests prese nted varied from 15.0 x 10 (exp 6) to 17.4 x 10 (exp 6) based on body length. Sting effects from this investigation are compared with data of jet effects on the same afterbodies. The results of this comparis on indicate that for the more gradually contoured afterbodies, a stin g shape can be found which will duplicate the jet effects, but that f or blunt afterbodies no solid sting shape will duplicate the jet effe cts.

Description: A flight investigation was conducted to determine the effect of jet exhaust on the drag, trim characteristics, and afterbody pressures on a 0.125-scale rocket model of the McDonnell F-101A airplance. Power-off data were obtained over a Mach number range of 1.04 to 1.9 and power-on data were obtained at a Mach number of about 1.5. The data indicated that with power-on the change in external drag coefficient was within the data accuracy and there was a decrease in trim angle of attack of 1.27 degrees with a corresponding decrease of 0.07 in lift coefficient. Correspondingly, pressure coefficients on the side and bottom of the fuselage indicated a positive increment near the jet exit. As the distance downstream of the jet exit increased, the increment on the bottom of the fuselage increased, whereas the increments on the side decreased to a negative peak.

Description: The technical memorandum briefly summarizes the growth of interest in aeroelastic phenomena as aircraft speed increased and wing designs changed for faster aircraft. Different types of aircraft vibrations are then introduced, and the mathematical basis for the theory behind them is described. Special attention is given to static oscillations, wing flutter, and the flutter of skin panels. The last section of the memorandum deals with the prevention of flutter by design specifications.

Description: A combined analytical and experimental determination is made of the coupled natural frequencies and mode shapes in the longitudinal plane of symmetry for a dynamic model of a single-rotor helicopter. The analytical phase is worked out on the basis of a seven-degree-of-freedom system combining elastic deflections of the rotor blades, rotor shaft, pylon, and fuselage. The calculated coupled frequencies are first compared with calculated uncoupled frequencies to show the general effects of coupling and then with measured coupled frequencies to determine the extent to which the coupled frequencies can be calculated. The coupled mode shapes are also calculated and were observed visually with stroboscopic lights during the tests. A comparison of the coupled and uncoupled natural frequencies shows that significant differences exist between these frequencies for some of the modes. Good agreement is obtained between the measured and calculated values for the coupled natural frequencies and mode shapes. The results show that the coupled natural frequencies and mode shapes can be determined by the analytical procedure presented herein with sufficient accuracy if the mass and stiffness distributions of the various components of the helicopter are known.

Description: A study is made of aerodynamic performance and static stability and control at hypersonic speeds. In a first part of the study, the effect of interference lift is investigated by tests of asymmetric models having conical fuselages and arrow plan-form wings. The fuselage of the asymmetric model is located entirely beneath the wing and has a semicircular cross section. The fuselage of the symmetric model was centrally located and has a circular cross section. Results are obtained for Mach numbers from 3 to 12 in part by application of the hypersonic similarity rule. These results show a maximum effect of interference on lift-drag ratio occurring at Mach number of 5, the Mach number at which the asymmetric model was designed to exploit favorable lift interference. At this Mach number, the asymmetric model is indicated to have a lift-drag ratio 11 percent higher than the symmetric model and 15 percent higher than the asymmetric model when inverted. These differences decrease to a few percent at a Mach number of 12. In the course of this part of the study, the accuracy to the hypersonic similarity rule applied to wing-body combinations is demonstrated with experimental results. These results indicate that the rule may prove useful for determining the aerodynamic characteristics of slender configurations at Mach numbers higher than those for which test equipment is really available. In a second part of the study, the aerodynamic performance and static stability and control characteristics of a hypersonic glider are investigated in somewhat greater detail. Results for Mach numbers from 3 to 18 for performance and 0.6 to 12 for stability and control are obtained by standard text techniques, by application of the hypersonic stability rule, and/or by use of helium as a test medium. Lift-drag ratios of about 5 for Mach numbers up to 18 are shown to be obtainable. The glider studied is shown to have acceptable longitudinal and directional stability characteristics through the range of Mach numbers studied. Some roll instability (negative effective dihedral) is found at Mach numbers near 12.

Description: An investigation was performed in the Langley Unitary Plan wind tunnel to determine the aerodynamic characteristics of a model of a 450 swept-wing fighter airplane, and to determine the loads on attached stores and detached missiles in the presence of the model. Also included was a determination of aileron-spoiler effectiveness, aileron hinge moments, and the effects of wing modifications on model aerodynamic characteristics. Tests were performed at Mach numbers of 1.57, 1.87, 2.16, and 2.53. The Reynolds numbers for the tests, based on the mean aerodynamic chord of the wing, varied from about 0.9 x 10(exp 6) to 5 x 10(exp 6). The results are presented with minimum analysis.

Description: Results have been obtained from an investigation in the Langley Unitary Plan wind tunnel at Mach numbers from 2.5 to 3.5 of a canard-type configuration designed for supersonic cruise flight. Tests extended over an angle-of-attack range from about -4 deg to 11 deg and an angle-of-sideslip range from -4 deg to 6 deg. For the present tests, the results indicate that forebody deflection was an efficient means of providing a sizable positive pitching-moment shift with little or no increase in drag. The test configuration had a trimmed lift-drag ratio of approximately 6.0 at Mach numbers near 3.0 and at a Reynolds number of 2.52 x 10(exp 6). The configuration was both longitudinally and directionally stable. The lift-drag ratios are believed to be somewhat low inasmuch as the models used for the present tests had large-grain-size transition strips fixed to the various surfaces and these strips added wave drag. Also, the model boundary- layer diverter is oversized with respect to a full - scale configuration and therefore contributes additional drag.

Description: The factors which influence the selection of landing approach speeds are discussed from the pilot's point of view. Concepts were developed and data were obtained during a landing approach flight investigation of a large number of jet airplane configurations which included straight-wing, swept-wing, and delta-wing airplanes as well as several applications of boundary-layer control. Since the fundamental limitation to further reductions in approach speed on most configurations appeared to be associated with the reduction in the pilot's ability to control flight path angle and airspeed, this problem forms the basis of the report. A simplified equation is presented showing the basic parameters which govern the flight path angle and airspeed changes, and pilot control techniques are discussed in relation to this equation. Attention is given to several independent aerodynamic characteristics which do not affect the flight path angle or airspeed directly but which determine to a large extent the effort and attention required of the pilot in controlling these factors during the approach. These include stall characteristics, stability about all axes, and changes in trim due to thrust adjustments. The report considers the relationship between piloting technique and all of the factors previously mentioned. A piloting technique which was found to be highly desirable for control of high-performance airplanes is described and the pilot's attitudes toward low-speed flight which bear heavily on the selection of landing approach speeds under operational conditions are discussed.

Description: An experimental investigation of the internal-flow conditions of a J71 experimental turbine equipped with 97-percent-design stator areas was conducted at equivalent design speed and near equivalent design work. The results of the investigation indicate that the stage work distribution closely approximates design, the actual distribution being 44.1, 33.4, and 22.5 percent for the first, second, and third stages, respectively. The first-, second-, and third-stage efficiencies were 0.894, 0.858, and 0.792, respectively. The first and second stages exhibited loss regions near the hub and tip at the rotor blade outlets. The hub loss region is attributed to stator secondary flows, and a contributing factor to the tip loss region may be the high design diffusion on the rotor blade suction surface near the tip. The loss in the third stage is appreciably greater than that in the first or second stage. The fact that the third rotor is unshrouded and has a nominal tip clearance of 0.120 inch may contribute to the higher loss in the tip region of the third stage.

Description: An investigation has been conducted in the Langley 20-foot free-spinning tunnel on a l/19-scale model of the North American T-28C airplane to determine the spin and recovery characteristics. The T-28C airplane is similar to the T-28B airplane except for slight modifications for the arresting hook. The lower rear section of the fuselage was cut out and, consequently, the lower part of the rudder was removed to make a smooth fairing with the fuselage. The T-28B airplane had good recovery characteristics; but these modifications, along with the addition of gun packages on the wings, led to poor and unsatisfactory spin-recovery characteristics during demonstration spins of the T-28C airplane. Model test results indicated that without the gun packages installed, satisfactory recoveries could be obtained if the elevators were held full back while the rudder was fully reversed and the ailerons were held neutral. However, with the addition of gun packages to the wings and the corresponding change in loading, recoveries were considered unsatisfactory. Recoveries attempted by using a larger chord or larger span rudder were improved very slightly, but were still considered marginal or unsatisfactory. Strakes placed on the nose of the model were effective in slowing the spin rotation slightly and, in most instances, decreased the turns for recovery slightly. Recovery characteristics were slightly marginal for the full fuel loading when strakes and the extended-chord rudder were installed; but with the wing fuel partly used, recovery characteristics were again considered unsatisfactory or, at least, definitely on the marginal side. The optimum control technique for recovery is movement of the rudder to full against the spin with the stick held full back (elevators full up) and the ailerons held neutral, followed by forward movement of the stick only after the spin rotation ceases. Inverted-spin test results indicate that the airplane will spin steep and fast and that recovery by full rudder reversal will be satisfactory if the ailerons are held neutral.

Description: An investigation has been conducted in the 27- by 27-inch preflight jet of the Langley Pilotless Aircraft Research Station at Wallops Island, Va., of the release characteristics of a dynamically scaled streamlined-type internally carried store from a simulated bomb bay at Mach numbers M(sub o) of 0.8, 1.4, and 1.98. A l/17-scale model of the Republic F-105 half-fuselage and bomb-bay configuration was used with a streamlined store shape of a fineness ratio of 6.00. Simulated altitudes were 3,400 feet at M(sub o) = 0.8, 3,400, and 29,000 feet at M(sub o) = 1.4, and 29,000 feet at M(sub o) = 1.98. At supersonic speeds, high pitching moments are induced on the store in the vicinity of the bomb bay at high dynamic pressures. Successful ejections could not be made with the original configuration at supersonic speeds at near sea-level conditions. The pitching moments caused by unsymmetrical pressures on the store in a disturbed flow field were overcome by replacing the high-aspect-ratio fin with a low-aspect-ratio fin that had a 30-percent area increase which was less subject to aeroelastic effects. Release characteristics of the store were improved by orienting the fins so that they were in a more uniform flow field at the point of store release. The store pitching moments were shown to be reduced by increasing the simulated altitude. Favorable ejections were made at subsonic speeds at near sea-level conditions.

Description: A negligible effect on turbine efficiency and only a small decrease in turbine weight flow were observed when the J71 experimental turbine with 97-percent-design stator areas was modified to include shrouding of the third-stage rotor.

Description: The hazards of lightning strokes to aircraft fuel tanks have been investigated in artificial-lightning-generation facilities specifically constructed to duplicate closely the natural lightning discharges to air craft determined through flight research programs and analysis of lightning-damaged aircraft over a period of many years. Explosion studies were made in an environmental explosion chamber using small fuel tanks under various simulated flight conditions. The results showed that there is a primary hazard whenever there is direct puncture of the fuel-tank wall, whereas the ignition of fuel by hot spots on tank walls due to lightning strikes is unlikely. Punctures of fuel-tank walls by artificial-lightning discharges produced explosions of the fuel in the mixture range from excessively lean to rich mixtures. None of the aluminum alloys, 0.081 inch thick or over, were punctured by the laboratory discharges representative of natural-lightning discharges to aircraft; however, reliance on this wall thickness for complete protection would not be justified, because occasional strokes are known to be of greater magnitude and because statistics reveal variations in the damage pattern. Data gathered by the Lightning and Transients Research Institute on lightning strokes to aircraft show that 90 percent of the strokes recorded have occurred in the temperature range of -10 to +10 C, where many of the jet fuels are flammable but where aviation gasoline is overrich. Also, 10 percent of the strokes recorded have been to the wings, which are the principal fuel-storage areas for modern aircraft. Thus, there is a hazard, particularly for jet fuels. Certain protective measures are indicated by the studies to date, such as the use of lightning diverter rods, thickening of the wing skin in areas near the most probable stroke paths, and the use of fuel-tank liners in critical areas.

Description: An investigation has been made to determine the aerodynamic characteristics in pitch at a Mach number of 6.8 of hypersonic missile configurations with cruciform trailing-edge flaps and with all-movable control surfaces. The flaps were tested on a configuration having low-aspect-ratio cruciform fins with an apex angle of 5 deg the all-movable controls were mounted at the 46.7-percent body station on a configuration having a 10 deg flared afterbody. The tests were made through an angle-of-attack range of -2 deg to 20 deg at zero sideslip in the Langley 11-inch hypersonic tunnel. The results indicated that the all-movable controls on the flared afterbody model should be capable of producing much larger values of trim lift and of normal acceleration than the trailing-edge -flap configuration. The flared -after body configuration had considerably higher drag than the cruciform-fin model but only slightly lower values of lift drag ratio.

Description: Information on landing gear stresses is presented on the following: vibratory phenomena, tangential forces applied to landing gear, fore and aft oscillations of landing gears, examples of fatigue failures, vibration calculations, and improvement of existing test equipment.

Description: The National Advisory Committee for Aeronautics has conducted a flight test of a model approximating the McDonnell F3H-lN airplane configuration to determine its pitch-up and buffet boundaries, as well as the usual longitudinal stability derivatives obtainable from the pulsed- tail technique. The test was conducted by the freely flying rocket- boosted model technique developed at the Langley Laboratory; results were obtained at Mach numbers from 0.40 to 1.27 at corresponding Reynolds numbers of 2.6 x 10(exp 6) and 9.0 x 10(exp 6). The phenomena of pitch-up, buffet, and maximum lift were encountered at Mach numbers between 0.42 and 0.85. The lift-curve slope and wing-root bending-moment slope increased with increasing angle of attack, whereas the static stability decreased with angle of attack at subsonic speeds and increased at transonic speeds. There was little change in trim at low lift at transonic speeds.

Description: A ditching investigation was made of a l/l2-scale dynamically similar model of the Douglas F4D-1 airplane to study its behavior when ditched. The model was landed in calm water at the Langley tank no. 2 monorail. Various landing attitudes, speeds, and configurations were investigated. The behavior of the model was determined from visual observations, acceleration records, and motion-picture records of the ditchings. Data are presented in tables, sequence photographs, time-history acceleration curves, and attitude curves. From the results of the investigation, it was concluded that the airplane should be ditched at the lowest speed and highest attitude consistent with adequate control (near 22 deg) with landing gear retracted. In a calm-water ditching under these conditions the airplane will probably nose in slightly, then make a fairly smooth run. The fuselage bottom will sustain appreciable damage so that rapid flooding and short flotation time are likely. Maximum longitudinal deceleration will be about 4g and maximum normal acceleration will be about 6g in a landing run of about 420 feet, In a calm-water ditching under similar conditions with the landing gear extended, the airplane will probably dive. Maximum longitudinal decelerations will be about 5-1/2g and maximum normal accelerations will be about 3-1/2g in a landing run of about 170 feet.

Description: This paper contains tail and hull loads data obtained in an investigation of a l/15-scale model of the Goodyear XZP5K airship. Data are presented in the form of tabulated pressure coefficients over a pitch and yaw range of +/-20 deg and 0 deg to 30 deg respectively, with various rudder and elevator deflections. Two tail configurations of different plan forms were tested on the model. The investigation was conducted in the Langley full-scale tunnel at a Reynolds number of approximately 16.5 x 10(exp 6) based on hull length, which corresponds to a Mach number of about 0.12.

Description: An investigation has been completed in the Langley 20-foot free-spinning tunnel on a l/24-scale model of the Grumman F11F-1 airplane to determine its spin and recovery characteristics. An interim report, Research Memorandum SL55G20, was published earlier and the present report concludes the presentation of results of the investigation. Primarily, the present report presents results obtained with engine gyroscopic moments simulated on the model. Also, the current results were obtained with a revised larger vertical tail recently incorporated on the airplane. It was difficult to obtain developed spins on the model when the spin direction was in the same sense as that of the engine rotation (right spin on the airplane). The developed spins obtained were very oscillatory and the recoveries were unsatisfactory. These results were similar to those previously reported for which engine rotation was not simulated. When the spin direction was in the opposite sense (left spin on the airplane), however, developed spins were readily obtainable. Recoveries from these spins also were unsatisfactory. Satisfactory recoveries were obtained on the model, however, when rudder reversal was accompanied by extension of small canards near the nose of the airplane or by deflection of the horizontal tail differentially with the spin.

Description: A supplementary investigation to determine the effect of external fuel tanks on the spin and recovery characteristics of a l/28-scale model of the North American FJ-4 airplane has been conducted in the Langley 20-foot free-spinning tunnel. The model had been extensively tested previously (NACA Research Memorandum SL38A29) and therefore only brief tests were made to evaluate the effect of tank installation. Erect spin tests of the model indicate that flat-type spins-are more prevalent with 200-gallon external fuel tanks than with tanks not installed. The recovery technique determined for spins without tanks, rudder reversal to full against the spin accompanied by simultaneous movement of ailerons to full with the spin, is recommended for spins encountered with external tanks installed. If inverted spins are encountered with external tanks installed, the tanks should be jettisoned and recovery attempted by rudder reversal to full against the spin with ailerons maintained at neutral.

Description: An investigation has been made in the Langley 4- by 4-foot supersonic pressure tunnel at a Mach number of 1.41 to determine the aerodynamic characteristics of an 0.03-scale model of the Avro CF-105 airplane. The investigation included the determination of the static longitudinal and lateral stability, the control and the hinge-moment characteristics of the elevator, the aileron, and the rudder, as well as the vertical-tail-load characteristics. The results indicated a minimum drag coefficient of about 0.0270, and a maximum trimmed lift-drag ratio of about 4.25 which occurs at a lift coefficient of 0.16. The directional stability decreased with increasing angle of attack until a region of static instability occurred above an angle of attack of about 9 deg.

Description: The evaluation of the altitude operational characteristics was part of the over-all investigation of the early developmental Iroquois engine. Engine steady-state windmilling characteristics were evaluated over a range of flight Mach numbers from 0.48 to 1.72 at altitudes of 35,000 and 50,000 feet. Engine altitude ignition limits were obtained over a range of flight Mach numbers from 0.5 to 1.5 with the standard engine ignition system and also with an oxygen boost system. A short investigation of high-speed altitude reignition following combustor blowout was conducted.

Description: As a part of this investigation, the acceleration characteristics of the engine, using the standard engine fuel-control system, were obtained for conditions simulating flight at altitudes of 35,000 and 50,000 feet with a flight Mach number of 0.4. Rapid and wave-off type accelerations were made at each flight condition, and the transient performance of the engine was recorded with a multiple-channel oscillograph. The parameters are presented graphically in the form of time histories, augmented by short segments of the oscillograph recordings, in order to more completely describe the behavior of the engine parameters when surge was encountered.

Description: This document is a compilation of papers presented at the Conference on the Progress of the X-15 project held at the Langley Aeronautical Laboratory on 25-26 October 1956. The conference was held by the Research Airplane Committee of the U. S. Air Force, the U. S. Navy, and the National Advisory Committee for Aeronautics to report on the technical status of this research airplane. The papers were presented by members of the staffs of North American Aviation, Inc., Reaction Motors, Inc., and NACA.

Description: This report is a complilation of practical rules, derived at the same time from theory and from experience, intended to guide the aeronautical engineer in the design of flutter-free airplanes. Rules applicable to the wing, the ailerons, flaps, tabs,tail surfaces, and fuselage are discussed.

Description: An experimental investigation has been made to determine the dynamic stability and control characteristics of a 1/5-scale flying model of a jet-powered vertical-attitude VTOL research airplane in hovering and transition flight. The model was powered with either a hydrogen peroxide rocket motor or a compressed-air jet exhausting through an ejector tube to simulate the turbojet engine of the airplane. The gyroscopic effects of the engine were simulated by a flywheel driven by compressed-air jets. In hovering flight the model was controlled by jet-reaction controls which consisted of a swiveling nozzle on the main jet and a movable nozzle on each wing tip; and in forward flight the model was controlled by elevons and a rudder. If the gyroscopic effects of the jet engine were not represented, the model could be flown satisfactorily in hovering flight without any automatic stabilization devices. When the gyroscopic effects of the jet engine were represented, however, the model could not be controlled without the aid of artificial stabilizing devices because of the gyroscopic coupling of the yawing and pitching motions. The use of pitch and yaw dampers made these motions completely stable and the model could then be controlled very easily. In the transition flight tests, which were performed only with the automatic pitch and yaw dampers operating, it was found that the transition was very easy to perform either with or without the engine gyroscopic effects simulated, although the model had a tendency to fly in a rolled and sideslipped attitude at angles of attack between approximately 25 and 45 deg because of static directional instability in this range.

Description: An investigation has been made in the Langley 4 by 4-foot supersonic pressure tunnel at Mach numbers of 1.82 and 2.01 to determine the longitudinal and lateral static-stability characteristics of a 0.04-scale model of the Lockheed F-104A airplane. The effects of a modified vertical tail, several ventral-fin arrangements, and several external store arrangements were also determined. The tests were made at Reynolds numbers of 1.02 (exp 6) and 1.382 (exp 6), respectively, based on the wing mean geometric chord. The tests were made of combined angles of attack and sideslip that varied from about -4 deg. to about 20 deg.

Description: This report presents the results of tests of a .35-scale model of the Bell P-39N-1 airplane. Included are the longitudinal-stability and -control characteristics of the airplane as indicated by tests of the model equipped with each of two different sets of elevators. The results indicate good longitudinal stability and control throughout the speed range encounterable in flight. The variation of estimated stick force with speed was less when the model was equipped with elevators constructed to the theoretical design dimensions than when equipped with elevators as built to scale from measurements of the corresponding parts of the actual airplane. The predicted stick forces required to produce the normal accelerations attainable in flight are within the limits specified by the Army Air Forces.

Description: Additional wind-tunnel tests were made of a 1/8-scale model of the Republic XP-91 airplane to determine its characteristics with various modifications. The modifications included a revised conventional tail, revised rocket arrangement, drooped wing tips, and revised landing gear and doors. Tests were also made to determine the effectiveness of the control surfaces of the model with the conventional tail and the effect of changing wing incidence and tail length. The revised rocket arrangement provided a considerable increase in the static directional stability contributed by the vee tail at small angles of yaw. The conventional tail provided a greater static directional stability than the vee tail without increasing the rolling moment due to sideslip. The rolling moment die to sideslip was considerable reduced by either drooped wing tips or open main landing-gear doors. The reduction in rolling moment due to sideslip resulting from the drooped tips was less with the landing-gear doors open than with the doors closed. A change in wing incidence from 0 degrees to 6 degrees reduced the elevator angle required for balance by approximately 6 degrees.