ALBERT

Notizen: The geologist's use of air photographs and the characteristics studied by photogeologists are briefly described. The influence of photographic factors such as scale, season, time of day, film type, processing, overlap and dimensional accuracy are considered from the geologist's viewpoint.

Notizen: This paper modifies the well-known formula that corrects x-parallaxes for tilt. It shows how we can make significant improvements in accuracy with a no more complicated formula, in which the effects of ground relief are completely removed; and how we can reduce the second-order errors due to lateral (w) tilts by very large factors in favourable cases.

Notizen: The history of the Argentine-Chile frontier is briefly reviewed. The paper then describes the photogrammetric and land-surveying work that formed part of the recent settlement of a section of the frontier, that was referred to the British Government for arbitration.

Notizen: Topics of immediate practical interest formed the basis of the Address. Particular emphasis was placed upon problems of point transfer, pre-marking of ground control points, aerial triangulation by observation of independent models, and the status of photogrammetric operators.

Notizen: The article describes a method of strip aerial triangulation using the Wild B8 plotter. The principal feature of the method is the transfer of exterior orientation of a camera by measurement of outer orientation parallel to successive airbases.

Notizen: The object of this paper is to provoke discussion and not to present a finished study. It deals briefly with quantitative analysis of drainage patterns in geomorphological studies and refers to methods that have recently received some attention in the United States. It points to the value of aerial photographs in such studies and asks for discussion of two important points: firstly, whether the mathematical approach is soundly based; and, secondly, whether the analytical method is likely to give useful practical results.

Notizen: SYNOPSIS. Broad scope investigations have allowed a study of the intestinal parasitic protozoa of the Kenya baboon Papio doguera in its natural habitat as well as an opportunity to follow the intestinal protozoan populations in these primates held in captivity. Samplings indicate that the amoebae found in the baboon are essentially the same as those which commonly occur in man. Balantidium coli is frequent in wild baboons but is self-limiting in animals after a few weeks in captivity. The flagellates Chilomastix mesnili and Giardia lamblia were detected in captive but not in wild baboons; the presence of the latter constitutes a new record for Papio doguera.

Notizen: SYNOPSIS. Experimental observation of the pathogenicity of some strains of Hartmannella plus the observation of human meningo-encephalitis due to small amebas which had a structure compatible with that of Hartmannella in the tissues has suggested the concept of respiratory amebiasis followed by cerebral and other complications.Until recently no cultural evidence was available to identify positively the amebas in the human cases. This report summarizes the isolation of Naegleria sp. (HB-1) from human spinal fluid by mouse inoculation followed by tissue culture of the infected mouse brain. C. Butt and his associates, who submitted this material to us, isolated the Naegleria on agar medium with Escherichia coli without antibiotics at 37 C.The new isolate failed to grow on the medium previously suggested by us for Hartmannella. HB-1 is virulent for laboratory animals and has a structure in the tissues which more resembles the amebas in the human tissue than the amebas in experimental Hartmannella infections of mice. Naegleria and Hartmannella are both potential pathogens for normal animals and man. A clinical laboratory method to detect Naegleria as well as Hartmannella is herein suggested.

Notizen: SYNOPSIS. Reticulocytosis, stimulated by the destruction of red blood cells by phenylhydrazine, altered the course of infection of both Plasmodium chabaudi and P. berghei in the mouse. P. chabaudi, lacking a preference for reticulocytes, was adversely affected when young cells were present in abundance. Parasitemias diminished and most of the animals survived the otherwise fatal infection. P. berghei preferentially invaded reticulocytes to the extent that the parasitemia became contained largely in the reticulocyte population. This was accompanied by a delay in time to death.

Notizen: SYNOPSIS. Uronema nigricans, a hymenostome ciliate, is redescribed by modern technics. Anatomic studies were made on 4 strains treated primarily with the Chatton-Lwoff silver impregnation technic. Particular attention was given to the buccal apparatus and its importance to generic assignment in the order Hymenostomatida.

Notizen: SYNOPSIS. A hyperparasite probably related to some lower protistan was found in the cytoplasm of Entamoeba suis Hartmann. These were very minute bodies with a central Feulgen-positive dot, the nucleus, and a bordering cytoplasmic ring with an alcian blue-positive reaction. This organism appeared to interfere with the synthesis of DNA & RNA in the host amoeba as reflected in its relative stainability with Feulgen or pyronin-methyl green. The suggestion is that the parasitized amoebic cysts were most likely rendered nonviable.

Notizen: SYNOPSIS. Cell-free preparations from Crithidia jasciculata carried out protein synthesis as measured by 14C-leucine uptake (optimum ∼ 10 mM Mg++) and poly U-directed 14C-phenylalanine uptake (optimum ∼ 16 mM Mg++). Characteristics of the system and sucrose density-gradient patterns of ribosomes were investigated. The charging and transfer reactions—the 2 main steps in protein synthesis—were inhibited by stilbamidine, hydroxystilbamidine, pentamidine, quinapyramine (Antrycide), and suramin.

Notizen: SYNOPSIS. Cohnilembus verminus, a marine hymenostome ciliate, is described from a culture taken at Eniwetok. Anatomic studies were made on specimens treated primarily with the Chatton-Lwoff silver impregnation technic.

Notizen: SYNOPSIS. Eimeria callospermophili was found in 6 species of ground squirrels and the white-tailed prairie dog. The hosts included Spermophilus armatus from Utah and Montana, S. richardsoni from Montana and Wyoming, S. beecheyi from California, S. lateralis and S. variegatus from Utah, and S. tridecemlineatus and Cynomys leucurus from Wyoming. Infections were generally transmissible from each species of ground squirrel to S. armatus and S. richardsoni. Oocysts from C. leucurus caused infections in S. armatus and S. richardsoni. No infections were found after inoculation of E. callospermophili oocysts into least chipmunks (Eutamius minimus), Mongolian gerbils (Meriones unguiculatus), or laboratory rats; however, excystation occurred in these animals. Resistance to infection did not develop in S. armatus, S. richardsoni, or S. variegatus, but did occur after 5 or more infections in S. lateralis. Eimeria callospermophili had little or no effect on the host in S. armatus, S. lateralis, or S. variegatus, but caused bloody diarrhea in severely infected individuals of S. richardsoni.The oocysts had an oocyst residuum consisting of several distinct bodies, which later coalesced to form a large homogeneous body. Each sporozoite had an unusually large refractile body. In experimentally infected specimens of S. armatus the prepatent period and patent period lasted for 5 and 9 days, respectively. Mature 1st-generation schizonts, first seen 2 days after inoculation, had 8–12 merozoites. Mature 2nd-generation schizonts, first seen 3 days after inoculation, had an average of 18 merozoites which were smaller than those of the 1st generation. Mature gametes were 1st seen 4 days after inoculation. Mature microgametocytes were only slightly larger than mature macrogametes.

Notizen: SYNOPSIS. The conclusion drawn in 1921 that the large nuclei in the cytoplasmic cortex of Glugea cysts are not vegetative nuclei of the microsporidan but nuclei of the hypertrophied host cell was based on the discovery of early developmental stages in the mesenchyme of stickleback larvae experimentally fed Glugea spores. This observation had been made on serial sections from experiments done in 1912. The intracellular development of the microsporidan could be followed up in this material only thru the 1st stages of schizogony. Renewed infection experiments, done still in 1921 on a much broader basis, have fully confirmed the previous findings, as briefly stated in 1922. On this material, the intracellular development of G. anomala has been followed up in recent years from uninucleate host cells 7 μ in diameter, interpreted as wandering cells in the mesenchyme, until they became macroscopic multinucleate cysts, in which schizogony and sporogony of the microsporidan produced innumerable vegetative stages and spores of Glugea. The details of the developmental processes are described in the present paper.The multinucleate host cell and the intracellular parasites together form one of the symbiotic complexes for which the term “xenom” or “xenoma” has been used by me since 1949. By a sequence of amitotic nuclear divisions, the uninucleate host cell in the Glugea xenomas of Gasterosteus becomes plurinucleate in contrast to the usual structure of other xenomas of fish.Already in 1921, I thought that the host cell in the Glugea xenomas may have phagocytic properties. The observation of accumulation of granules from pigment cells in some of the Glugea xenomas has now verified this supposition.

Notizen: SYNOPSIS. Eimeria eumopos n. sp. (Coccidiida, Eimeriidae) from a Colombian bat Eumops trumbulli (Chiroptera, Molossidae) is described. This is the first recorded coccidium in a bat from the western hemisphere, and the sixth bat coccidium species described to date. The unsporulated oocysts in the bat feces are 30.9–24.0 by 28.9–23.2 μ (near 28.8 × 26.1 μ). Their outstanding feature is the pronounced pitting of the thick brownish oocyst wall.

Notizen: SYNOPSIS. An electron microscope study of Plasmodium coatneyi in the rhesus monkey supplied information on the fine structure of trophozoites, gametocytes and of the host cell. The trophozoites resemble other mammalian malaria parasites. They do not have typical protozoan mitochondria, but instead a concentric double-membraned organelle, which, it is assumed, performs mitochondrial functions. They feed on the host cell by pinocytosis, engulfing droplets of erythrocytes thru invaginations of the plasma membranes at any region of the cell or thru the cytostome. Digestion of hemoglobin takes place in small vesicles pinched off from the food vacuole proper.Gametocytes can be clearly distinguished into macro- and microgametocytes. Macrogametocytes are covered by 2 plasma membranes, the inner one appearing thicker in some places. The cytoplasm is filled with Palade's particles and has numerous vesicles of endoplasmic reticulum and toxonemes. In microgametocytes most of the inner membrane is thickened, the cytoplasm has few Palade's particles and vesicles of the endoplasmic reticulum and does not have toxonemes.Erythrocytes with trophozoites are irregularly scallop-shaped and have elevated points with knob-like protrusions covered by a double membrane. If these protrusions are sticky they might be in part responsible for clumping and arresting the schizonts and segmenters in the capillaries. The host cell contains numerous Maurer's clefts which in some instances are continuous with the membranes of the parasite suggesting that they might originate from them.

Notizen: SYNOPSIS. Mice, segregated in groups according to sex and age from 5 to 21 weeks, and randomly presented, were inoculated in one continuous process with a trypanosome suspension prepared from a Trypanosoma brucei subgroup stabilate of such a dilution that about 50% of the mice might be expected to become infected. No statistically significant difference occurred between groups, either with regard to sex or to age.Significant alterations in the proportions of mice infected did, however, occur in relation to inoculation order. The inoculation process occupied 12–197 minutes after removal of the stabilate from −79 C storage. Essentially, infectivity rose initially to a peak between 30 and 80 minutes, and then fell off, but was not abolished at the end of the experiment.

Notizen: SYNOPSIS. Observations were made on the fine structure of Paramecium bursaria and its intracellular Chlorella symbionts. Emphasis was placed on the structure of the algae and structural aspects of the relationship between the organisms.The algae are surrounded by a prominent cell wall and contain a cup-shaped chloroplast which lies just beneath the plasma membrane. Within the cavity formed by the chloroplast are a large nucleus, a mitochondrion, one or more dictyosomes, and numerous ribosomes. The chloroplast itself is made up of a series of lamellar stacks each containing 2–6 or more thylakoids with a granular stroma and starch grains intercalated between the stacks. The thylakoid stacks of mature algae are frequently more compact than those of recently divided algae. A large pyrenoid is located within the base of the chloroplast. It is made up of a granular or fibrillar matrix surrounded by a shell of starch. The matrix is bisected by a stack of 2 thylakoids. Prior to the division of the chloroplast the pyrenoid regresses; pyrenoids subsequently form in the daughter chloroplasts thru condensation of the matrix material and the reappearance of a starch shell. This shell appears to be formed by the hollowing-out of starch grains already present in the chloroplast stroma. Accordingly, in this case, starch moves from the stroma to the pyrenoid.The algae are located thruout the peripheral cytoplasm of the Paramecium. Each alga is located in an individual vacuole except immediately following division of the algae when the daughter cells are temporarily located in the vacuole which harbored the parental cell. Shortly thereafter the vacuole membrane invaginates, thereby isolating the daughter algae into individual vacuoles. Degenerating symbiotic algae are seen; because these are frequently found in vacuoles with bacteria, they are presumed to be undergoing digestion. Due to the conditions of culture these algae could have been either of intracellular or extracellular origin.

Notizen: SYNOPSIS. Electron-microscopic observations were performed on 2 species of Volvox, one similar to V. globator, the other to V. aureus. The former has distinct protoplasmic connections in the adult coenobium and specific structures, named “medial bodies,” in the connections just at the intersection with the middle lamella. The medial body is disk shaped, about 800 mμ in diameter, and is composed of 3 parts, 2 dense outer layers and an intermediate less dense zone. In the latter species, the connection and medial body were not seen. On the other hand, it was commonly seen in both of them that in younger, dividing gonidia neighboring protoplasts were connected with each other by protoplasmic bridges. The bridges are undoubtedly formed due to incomplete cell separation in the division of a gonidium. The structural difference in the adult coen***bium between the 2 species emerges just after inversion of the coenobium. In the globator type the medial body appears just after inversion, and the connection remains unruptured all thru life. In the aureus type, it seems that the connections are withdrawn or degenerate immediately after inversion. It is discussed whether protoplasmic continuity is really maintained by the connection or not in the freeswimming coenobium of Volvox.

Notizen: SYNOPSIS. Plasmodium lophurae hemozoin (malaria pigment) is a heme-containing protein which is distinctly different from hemoglobin and hematin by immunologic, spectrophotometric, fingerprint, heme-iron, gel filtration, and starch gel electrophoretic analyses. The calculated average molecular weight of P. lophurae hemozoin is ca. 40,000. Hemozoin contains at least 3 antigenic components and shows some indication of cross-reaction with hemoglobin.

Notizen: SYNOPSIS. In tryptone media, optimal growth of nonphotosynthetic Euglena gracilis var. bacillaris on glucose occurred with 1% (w/v) glucose at pH 3.5, and required a previous adaptive period in glucose medium.In short term metabolic experiments, glucose uptake was greatly stimulated by small concentrations of tryptone or succinate; effects of shaking suggested that CO2 has a similar stimulatory effect. Glucose utilization was highly dependent on glucose concentration, with an apparent threshold at about 2 mM and increasing steeply with glucose concentration above this value. In tracer experiments, about 90% of the glucose carbon consumed was assimilated, and about 10% released as CO2.Glucose did not stimulate respiration even during rapid glucose utilization. Tracer studies indicated oxidation of endogenous substrates was depressed by an amount which just compensated for the respiration due to glucose.The conditions which allowed rapid glucose utilization by “resting”E. gracilis var. bacillaris were the same as those known previously to be required for growth on glucose. It was therefore concluded that these factors act directly on the main pathways of glucose metabolism.

Notizen: In my article I have taken up different expressions for the terms of trade in foreign trade, and especially I have been interested in a breakdown of total gain into two parts, namely the part due to the terms-of-trade effects and the part due to the price level effects. I have also taken up the inter-sectoral gain from terms of trade and the relation to the terms of trade in foreign trade. Besides the usual index for terms of trade-the ratio between output prices and input prices-I have also introduced another index for terms of trade corresponding to the relation between the output price index and an index consisting of a weighted average of input prices and prices for final demand. Finally I have tried to give some emperical findings which should throw light on the development of the Danish terms of trade for the period 1949 to 1964.

Notizen: With few exceptions, only cormmodity flows and values which can be determined by means of commodity flows (flows of goods and services) are calculated in constant prices in the official national accounts of the Federal Republic of Germany. Figures an the industrial origin and the final use of the national product are published, the former according to thirty industries, the latter according to the major types of uses of which in particular private consumption expenditure has been further analysed.The computations at constant prices are based on market prices and not on factor costs. It is only on this basis that a uniform valuation of the production and the expenditure side can be made since the turnover tax, which is the most important indirect tax, is contained in the elements of final demand in varying shares and cannot be eliminated (the tax is part of the price and has cumulative effect).The computation at constant prices presupposes a breakdown of the values in current prices according to quantities and prices. This raises a number of problems, e.g. because seller and buyer may consider differing aspects-production costs, technical attributes, etc., on the one hand, and use etc., on the other hand. In part there exist only vague ideas, or no ideas at all, as to what is to be considered-from a theoretical point of view-as quantity and price. In other cases the two values can only with great difficulties, if at all, be quantified, or there exists no market price and only the production costs are available. The author deals in greater detail with differences in quality and new commodities, the determination and treatment of quantities and prices for services, in particular for trade services (services attached to goods), the computation of government services at constant prices considering the development of productivity in public service, the determination of the values calculated as balances, above all the treatment of changes in the terms of trade for net exports of goods and services, the computation of the contributions of industries to the gross domestic product and, finally, the reconciliation of the production and the expenditure side.In a third section the author deals with index formulae and the base year. In the majority of cases values are deflated; partly, however, they are currently adjusted by means of volume and quantity data. On the production side the two methods are in part combined.In a concluding section a survey is provided of the computation methods used in the Federal Republic of Germany and on the available material for the computations. Mention is made of depreciation at constant prices.

Notizen: A quarterly macro-econometric model of Japan's postwar economy has been constructed for the period 1954–1965 FY on the basis of standardized quarterly national income accounts. The model is designed for facilitating short-term economic forecasting and formulating adequate fiscal and monetary policy. Longer-term factors such as labor mobility, technical progress, etc., were also considered in the model.The model consists of fifty-three equations related to most of the macroeconomic variables in both money and real terms, and the equations were estimated in principle by the limited information maximum likelihood method. Principal exogenous variables related to policy instruments are government expenditures including transfers, parameters of tax functions, interest rate, and prices and fares controlled by the government, etc. In formulating the model, non-linear specifications were used whenever found necessary.Results of our testing on its predictive capability indicated fairly satisfactory performances for our observation period and also for 1966 FY. Multipliers related to fiscal and monetary policy were also obtained, indicating the dynamic characteristics of the Japanese economy, in particular, represented by dynamic business fixed investment, as compared with corresponding multipliers of the U.S. models.Although the model is exploratory and to serve as a core for a more disaggregated “Master Model,” the usefulness of the model for our purposes and the workability of our quarterly national accounts data for model-building have been recognized. The quarterly data, however, still remain to be improved especially in regard to consistency between income and expenditure and integration with flow-of-funds accounts.

Notizen: The measurement and inter-spatial comparison of Latin American real income levels calls for techniques which depart substantially from the conventional procedure of applying such official or free market exchange rates as happen to prevail in any given period. The reasons are varied, the main ones being that in an area such as Latin America prices are notoriously volatile, their structure differs radically from that encountered in other parts of the world, and the exchange rate system is characterized by frequent and usually irregular revisions, while in certain countries a multiple exchange rate system applies and no single factor is available for conversion purposes. In addition, there exists the problem common to all developing countries that the rates to a large extent reflect the exchange value of a limited number of export commodities vis-à-vis a wide range of imported goods and in no way typify the internal-external price relationship for the bulk of production which by its nature fails to enter into international trading transactions.The author has endeavoured to circumvent these difficulties by adopting the often-discussed “purchasing power parity” approach whereby national accounts data are converted into a common monetary denominator (in this case, the U.S. dollar) expressed in “real” or quantitative terms which as far as possible eliminate inter-spatial price differences. Results are presented and analyzed, first for the base year 1960, and then for the period 1955–1964 at the level of main expenditure sectors as well as for the total gross domestic product.To the extent that available statistics permitted, results for Latin American countries are also related to the United States and certain countries in Western Europe, a main objective being to determine the approximate dimension of the incomes “gap” and to ascertain whether this is increasing, decreasing or remaining very much unchanged in size.

Notizen: The main purpose of the study is to determine the savings potential of urban and rural households in India and in the process determine the possible savings and consumption functions separately for urban and rural areas.Four different possible functions have been used for determining the savings behaviour of the households both at the aggregate level and at the per capita level. The rural households, according to the results, have an extremely low rate of saving with income elasticity of saving of less than unity. For the urban households on the other hand, the income elasticity of saving is high enough to suggest the possibilities of considerably high savings potential.To understand the consumption behaviour of these households, the long-run and the short-run marginal propensities to consume and the marginal propensities to consume out of‘permanent’ or ‘normal’ income and ‘transitory’ income have been worked out. For the urban sector none of these give encouraging enough results and the analysis has been extended to examine whether other factors like prices and household assets are of any significance. Whereas for the rural sector, Milton Friedman's theory of ‘permanent’ or ‘normal’ income is somewhat substantiated, other factors like ‘transitory’ income, prices and assets appear to inthence urban consumption behaviour though no single one of them substantially enough. A negligible effect of ‘permanent’ income on urban consumption behaviour is, on the other hand, very clearly suggested by the results.Household consumption and savings have next been projected using the above results to determine the possible levels for the next three years. The results suggest that the rate of domestic savings likely to be achieved by the end of the Third Five Year Plan (1965–66) falls short of the targets laid down.

Notizen: Cet article résume brièvement les méthodes utilisées par le Service de la statistíque yougoslave dans le calcul du revenu national aux prix constants. En ce qui concerne l'industrie, la méthode utilisée consiste à multiplier le revenu net par unité dans l'annCe de base (distribué par type) par les quantités produites dans l'année en cours. Cet article discute également des autres méthodes possibles, et fait ressortir les raisons qui se trouvent à la base des choix effectués.La partie finale examine la validité des mesures obtenues; elle met en garde contre la tentation de procéder a des interprétations de caractére normatif sur la base de prix déterminés par voie administrative ou sujets a d'autres types de distortions. Des données, classées par industrie et par région, sont fournies pour la periode 1952–1965.

Notizen: In a number of underdeveloped countries today, adequate statistics for estimating national output by traditional national accounting methods are unavailable or unreliable. However, many of these same countries do publish data on monetary variables at an early stage in their development. These data can now be used to estimate national income.In this study the money supply was defined to include all currency in circulation, private deposits subject to check at all banks and postal systems, all government deposits, and unused overdrafts less float. The national accounts data were taken from United Nations sources and data supplied by various foreign statistical offices. To make the accounts more comparable in terms of coverage and to limit reported income to the monetized sector of the economy, non-monetary imputations were deleted.The monetary and national accounts data were combined in a multiple, stepwise regression. National income was used as the dependent variable and money supply and other data were used as the independent variables. The final estimating equations explained about 96 per cent of the variation in income between countries. Other tests were conducted using the currency ratio, transactions velocity, population, and per capita consumption. However, these variables did not augment the explanatory power of the regression equations.When the equations were used to estimate national income for twenty-two under-developed countries, the derived estimates showed a high degree of concordance with reported income where it existed for comparative purposes. The results indicate that monetary data can be used to estimate national income for underdeveloped countries with a relatively high degree of accuracy, between countries, and from year to year within a country.

Notizen: In The Present Paper The Author Reviews The Results Of An Investigation Aimed At Estimating The relative level of stocks in Hungary in terms of international comparisons. Though international comparison was limited by scarcity of data, it has still become evident that stocks as a whole, compared to production and sales, seem to be unnecessarily high. The investigation has been carried out in relation both to the level of stocks and their rate of increase.The global volume and building of stocks, however, did not give a satisfactory explanation, and the investigation had to be extended to the individual groups of stocks separately. In order to facilitate the comparison, stocks were classified into the following groups: agricultural stocks, goods in process, industrial finished goods and manufactures held by users, and retail stocks. The classification was based on the different function of the individual groups. This classification of stocks could be compared only with the data of the U.S A.The international comparison revealed that both the volume and the rate of increase of stocks in Hungary is unreasonably high. They are high even if we consider that the growth rate of the economy in Hungary was greater than in any of the countries examined.The author refers to the fact that the stock problem was one of the starting issues in the economic research process which led to the reform of the Hungarian economic management system introduced on 1st January 1968.

Notizen: The national income and product account (United Nations concept) in current prices itemized by distributive shares and by type of expenditure is given for the period 1929–1937. The national income by industrial origin and the reproducible national wealth are computed for the year 1930. Differences between the U.N. and the material concept are explained by means of the 1939 data.The national product series in real terms are computed (a) by means of the price deflation of the types of expenditure, and (b) as the physical output of goods and services by industrial origin (since 1926). Major changes In distributive shares are explained with the help of Price-cost analysis.The national product in real terms attains the lowest point in 1935 and not in 1933, as the industrial production and foreign trade series indicate. The structure of gross national expenditure reveals the same pattern of shifts, as is well known from other industrially developed countries during the business cycle.The development of national product by industrial origin, however, reveals some conspicuous singularities. Especially the uninterrupted increase in trade services (in terms of both persons engaged and turnover in constant prices) is an anomaly in the period of 1929–1937.Further, the Increase of rent (due to the gradual abolition of rent control), contrasting with the general fall of prices, led to a major shift in the distribution of national income during the early thirties. The other remarkable change resulting mainly from the changing price structure was the decrease of the farmers' share in national income.The production, transportation and distribution series in real terms reveal some time-lags. These result partly from the shift from the foreign to the home market, partly from the compensatory effects of stock movements, and partly from the delayed adjustment of consumers to declining income.

Notizen: This paper presents a new annual series for United Kingdom gross national product, at current and constant prices, calculated from the expenditure side. These results differ significantly from previous estimates in that they go back to the beginning of the railway age on an annual basis and also in that the constant price estimates involve a detailed deflation of the main components of expenditure on consumption and capital formation. The implications of the new results are summarised, with particular reference to rates of growth and relative price changes, and an appendix describes the sources of the estimates.

Notizen: Study of relationships between outputs, inputs, prices, and final demands in the United States can be strengthened by: (1) eliminating disparities in official measures of output (mainly the Index of Industrial Production and Real Gross National Product), and (2) obtaining agreement on the conceptual framework for studying these relationships.Real Gross Product has provided a consistent framework for study of productivity and prices for the total economy and for broad industry groups, but has not easily permitted the analysis of commodity detail particularly for intermediate commodities. Industrial Production, on the other hand, has considerably extended the detailed analysis of commodity output but has not provided a basis for systematic analysis of productivity and prices within a consistent framework for the total economy.This paper illustrates the effect of some of the disparities between Industrial Production and Gross Product in manufacturing on the analysis of relations between prices and output and prices and productivity. This is done for the 1954–1958 period when benchmark data are available for both measures. Inconsistencies for a number of industries cause difficulties in analyzing the interplay of demand and cost influences on price changes; for example, industries which rise above average in output and below in price in one measure are not the same as those in similar price-quantity relationships in the other measure.The paper concludes by recommending improvements in data and concept in order to eliminate some of the disparities and to enable analysts to reap the benefits of both types of measures of real output.

Notizen: Because of the recent public concern over the brain drain, this study attempts to measure the U.S. gain of highly skilled manpower. The paper discusses the serious short-comings of the data on gross immigration of scientists and engineers provided by the U.S. immigration authorities as a measure of true U.S. gains. In a case study of Swedish scientists and engineers it was found, for example, that whereas the U.S. data showed a gain of 106 Swedish scientists and engineers over a number of years, the net figure was only 26 after adjustment for remigration and the application of the proper OECD education criteria.The paper then reports the findings of a statistical study which uses the stock data on U.S. scientists in the National Register of Scientific and Technical Personnel to estimate the number of foreign born in this stock and analyse their characteristics with respect to age, educational attainment, and employment preferences.It was found that nearly 7 percent of all U.S. scientists are of foreign origin (foreign born and foreign secondary education), whereas 11.5 percent of all scientists with a Ph.D. are of foreign origin. The percentage among Ph.D. holders is highest in meteorology (22.3), followed by linguistics (18.7), physics (17.1) and statistics (14.6).The greatest percentage of scientists comes from Canada (10.4 per thousand), followed by Germany (8.3 per thousand) and the United Kingdom (6.7 per thousand). However, after adjustment of these data for the different sizes of the total foreign born population from each country in the U.S., it turns out that by this measure the greatest shares of scientists are supplied by the Japanese, followed by the Austrian-Swiss, Benelux and Canadians.The analysis of the age composition of all foreign born reveals that in the age groups that were 20–29, 45–54, and 65 and over in 1964 foreigners represent a smaller than average share, probably reflecting war casualties and education completed at a later age. Germans and Austrians are heavily concentrated in the group 55–64 years old in 1964, suggesting that a great share of scientists from these countries may have been victims of a brain push.

Notizen: This review article initially summarizes some of the highlights of the volume Why Growth Rates Differ, including the use of income shares as weights for the various factor inputs and some of the major factual conclusions drawn from the inter-country comparisons. Some of the main factors in differences in income levels and differences in growth rates are then reviewed.In appraising the contribution of the volume, the monumental task is emphasized. This study illustrates the adaptability of the approach which Denison developed initially in The Sources of Economic Growth. The volume meets many of the questions and criticisms raised of his earlier study, and should encourage a shift of the discussion from methodology towards the substance of the empirical results.The volume introduces some shifts in emphasis on the importance of different factors in growth. The role of demand variations and the contribution of capital is considered, but the evidence in the volume gives less emphasis on the importance of these factors than earlier work by others in both the United States and Europe. The volume gives some emphasis to shifts out of agriculture and the self-employed in the high postwar growth in many individual European countries. It considers the effects of reductions in trade barriers, and follows the view of most economists in playing this down. Advances in knowledge are also considered.Those who are interested in questions of economic growth, past and future, and economic policy in this area will find much in this volume for study and reflection.

Notizen: This study assesses the relationship of education and economic growth, economic development and economic progress in aggregate, in structural and in micro-economic terms on the basis of one hundred years of Canadian experience. Education is considered as a factor of input. The contribution made by knowledge resulting from additional education expands the capacity to produce, and increases the demand for goods and services and the desire for greater leisure. The dual function of education is stressed: the demand and supply effect. Education is examined both as a cause and a consequence of economic growth, economic development and economic progress, through its contribution to the quality of the labour force, earning capacity, both individual and national, productivity, the rate of economic growth and the character of economic development.The Canadian experience suggests that educational progress generally occurred in line with economic development during the first eight decades, with the real take-off in educational advancement only occurring in the last two decades, when the nation reached the stage of technological maturity and high mass-consumption. Among the reasons for the lower ratio of gross national product devoted to education in the first eight decades were the low priority attached to education, the emphasis on investment in physical capital because of its shorter pay-off period than investment in human capital, and the heavy reliance on a substantial flow of immigrants who had obtained their education and training abroad. A distinct change occurred, however, in the last two decades, partly as a result of new technological challenges and partly as the result of changes in private and public attitudes, as the recognition of the rewards of education in terms of individual advancement and social progress led to a greater willingness to devote an increasing proportion of the nation's resources to investment in human capital, long pay-off periods notwithstanding.

Notizen: Human capital concepts and measures have been applied and misapplied to an increasing variety of economic problem areas, two of which are examined.One of these is measurement of human capital gains and losses through migration. First requirements here are specification of the gaining or losing entities and of the relevant welfare functions. Alternatives in these respects are outlined. It is then argued that an appropriately adapted Fisherian present-value assessment of human capital is normally the correct measure. Replacement costs are a legitimate substitute only for young migrants with little cumulated learning through experience and even then they have usually been fallaciously applied. Probability adjustments for migration and re-migration are required in both cost and present-value assessments of human capital effects of migration-relevant policy alternatives, but the nature of those adjustments differs with the measurement approach used.For longitudinal analysis of contributions of human capital to economic growth, all measures of human capital stocks are inappropriate. A first principle of such analysis is measurement of resource inputs as flows. A coordinate principle requires that disaggregation be carried as far as necessary to distinguish essentially homogeneous categories of labor inputs. Though a way of separating out the schooling versus on-the-job-experience components of human capital is illustrated, it requires some strong assumptions. Splitting men into abstracted human capital components is better avoided in growth analysis. Furthermore, categorization of labor-force sub-groups could equally well provide the basis for rate-of-return assessments of marginal changes in the pace of investments in humans. Such assessments would incorporate the main elements of capital theory except valuation of the capital asset itself.Ultimately, human resource measurements for use in major public policy decisions relating to either growth or migration (or both) must incorporate modifications or error components that allow for development phenomena that elude marginal assessments. Among developing countries especially, a consideration of educational diffusion processes and dynamic productivity scale effects, for example, could have critical measurement and policy implications.

Notizen: This article discusses the revival of interest in research on cyclical behavior in the socialist countries, and the resulting shifting requirements placed upon the national income accounts. The first section discusses the economic experience and the institutional factors leading to this shift in emphasis. The second section deals with the use of national accounts in cyclical analysis, with particular reference to the Czechoslovak experience. The third section extends the discussion to the use of national accounts data for economic forecasting. The final section discusses the theory of economic fluctuations under socialism, and compares it with cyclical behavior in capitalist economies.

Notizen: The system of social accounts described in this article is based on the following five principles:(1) Producers of goods and services are working organizations which represent groups of people or individuals organized for the purpose of earning a living by producing goods and services that satisfy individual or collective needs. Business, government, profit and nonprofit, corporate and unincorporated working organizations are treated in a uniform way.(2) Since the behaviors of the market and non-market sectors differ considerably, these two sectors are consistently separated throughout the accounting system.(3) There are four basic activities: (a) production, (b) consumption, (c) investment, and (d) income redistribution. These call for four separate accounts: (a) Working Organizations, (b) Households, (c) Community, including government and certain non-government institutions, and (d) Accumulation. The fifth account, Rest of the World, serves for balancing purposes.(4) The same classifications of transactions are used for activities and institutions, making possible complete matching of social product and financial flows accounts.(5) The system strives to achieve the maximum analytical flexibility. Some of its possibilities are visible from the classification of industries: A. Market (Material) Sector: 1. Agriculture, II. Forestry, III. Mining and Manufacturing, IV. Construction, V. Transportation, VI. Trade and Catering, VII. Handicrafts; B. Non-Market (Non-Material) Sector: VIII. Housing and Communal Economy, IX. Education, Culture, and Social Welfare, X. Public Services Social Organizations (Political, Religious, etc.), Finance and Insurance, Public Administration and Judiciary, National Defence. Sector A corresponds to the material definition of social product. Sectors A + B correspond to the SNA definition. Sectors A + B minus Industry × reflects the welfare definition. Further, Industries I-IV produce goods, V-VII market services, VIII and IX non-market services with welfare content, X intermediate nonmarket services, V-X all services.

Notizen: The widespread use of common depth point techniques has emphasized the need for accurate static corrections. Manual interpretation methods can give excellent results, but a computer technique is desirable because of the great volumn of data recorded in common depth point shooting. The redundancy inherent in common depth point data may be used to compute a statistical estimate of the static corrections. The corrections are assumed to be time-invarient, surface-consistent, and independent of frequency. Surface consistency implies that all traces from a particular shot will receive the same shot static correction and all traces from a particular receiver position will receive the same receiver correction.Time shifts are computed for all input traces using crosscorrelation functions between common depth point traces. The time shift for each trace is composed of a shot static, a receiver static, residual normal moveout if present, and noise. Estimates of the shot and receiver static corrections are obtained by averaging different sets of the measured time shifts. Time shifts which are greatly in error are detected and removed from the computations.The method is useful for data which has a moderate to good signal to noise ratio. Residual normal moveout should be corrected before estimating the statics. The program estimates the statics for correctly stacking common depth point traces but it is not sensitive to constant or very slowly changing static errors.

Notizen: It was found in Part I of this paper that approximating the sharp cut-off frequency characteristic best in a mean square sense by an impulse response of finite length M produced a characteristic whose slope on a linear frequency scale was proportional to the length of impulse response, but whose maximum overshoot of ±9% was independent of this length (Gibbs' phenomenon). Weighting functions, based on frequency tapering or arbitrarily chosen, were used in Part II to modify the truncated impulse response of the sharp cut-off frequency characteristic, and thereby obtain a trade-off between the value of maximum overshoot and the sharpness of the resulting characteristic. These weighting functions, known as apodising functions, were dependent on the time-bandwidth product Mξ, where 2ξ, corresponded to the tapering range of frequencies.Part III now deals with digital filters where the number 2N–1 of coefficients is directly related to the finite length M of the continuous impulse response. The values of the filter coefficients are taken from the continuous impulse response at the sampling instants, and the resulting characteristic is approximately the same as that derived in Part II for the continuous finite length impulse response. Corresponding to known types of frequency tapering, we now specify a filter characteristic which is undefined in the tapering range, and determine the filter coefficients according to a mean square criterion over the rest of the frequency spectrum. The resulting characteristic is dependent on the time bandwidth product Mξ= (N–1/2)ξ up to a maximum value of 2, beyond which undesirable effects occur. This optimum partially specified characteristic is an improvement on the previous digital filters in terms of the trade-off ratio for values of maximum overshoot less than 1%. Similar to the previous optimum characteristic is the optimum partially specified weighted digital filter, where greater “emphasis is placed on reducing the value of maximum overshoot than of maximum undershoot”. Such characteristics are capable of providing better trade-off ratios than the other filters for maximum overshoots greater than 1/2%. However these filters have critical maximum numbers 2.NC–1 of coefficients, beyond which the resulting characteristics have unsuitable shapes. This type of characteristic differs from the others in not being a biassed odd function about its cut-off frequency.

Notizen: In Part I of this paper, we examined the properties of the best mean square approximation to the sharp cut-off frequency characteristic by an impulse response of finite length. It was found that the sharpness of cut-off for the resulting frequency characteristic depended on the length of the impulse response–but because of the discontinuous nature of the specified frequency characteristic, this best mean square approximation always had a maximum overshoot of ± 9%, independent of the length of the impulse response (Gibbs phenomenon).In Part II, we investigate ways of reducing this ± 9% overshoot at the expense of a reduced sharpness of cut-off. The discontinuous frequency characteristic is first approximated by a continuous characteristic with linear or cosine frequency tapering. The impulse response for such tapered characteristics consists of the impulse response of the discontinuous frequency characteristic weighted by a certain function corresponding to the type of tapering employed. The best mean square approximation to the tapered characteristic by an impulse response of finite length M will produce a frequency characteristic whose properties are now dependent on the time-band width product Mζ, where 2ζ is the tapering range.A trade-off exists between the maximum overshoot and the sharpness of cut-off for the resulting characteristic for both forms of frequency tapering. Instead of considering other forms of tapering in the frequency domain, we now investigate arbitrarily chosen weighting functions in the time domain to determine the minimum length of impulse response for a minimum value of maximum overshoot and a maximum value of sharpness of cut-off.Part III will discuss the digital realization of the above finite length impulse responses together with the optimum partially specified digital filter approximation to the desired frequency characteristic.

Notizen: Book reviewed in this article:Le Filtrage en Sismique, Tome IJ. AUBOUIN “Geosynclines” (Developments in Geotectonics 1). Elsevier Publishing CompanyEarth and Planetary Science Letters Vol. 1. Nr. 2H. Ramberg Gravity, Deformation and the Earth's Crust Academic Press“Potassium Argon Dating” Compiled by O. A. Schaeffer and J. Zähringer

Notizen: Deep seismic sounding was performed along two profiles which cross at the Dinarides area right angles. One of the profiles goes far into the Adriatic Sea.Besides considerations on the lithophysical conditions, characteristics of the registered waves are analysed. The amplitude curves and curves of amplitude ratios are shown. Special attention was paid to the frequency of the registered waves.In order to obtain a better knowledge of the registered wave pattern three-component recordings of waves were carried out. The analysis of the records obtained is given, with particular regard to the possibility of creating converted waves.The Earth's crust structure along the profiles II and III is given.

Notizen: Nomograms for solving equations in multilayer and dipping layer cases are presented. The nomograms constructed are used to solve the following equations: I. Intercept-time formula. 2. Critical distance formula. 3. Critical angle formula. 4. Critical angle and dip angle formula. 5. Vertical depth formula.

Notizen: Using a comprehensive theory of the vertical force variometer, it is shown that the mean of the two readings taken in azimuths 180 degrees apart only eliminates the error of misorientation and of inclination of the knife edge if these factors are sufficiently small. The necessary accuracy in the 180 degree rotation and in the readjustment of the levels are investigated and a practical test is developed to allow the initial adjustments to be determined. Finally, a brief description of a new variometer tripod is given.

Notizen: It is known that good use can be made of calculating the second vertical derivative of gravitational and magnetic fields. The first derivative, or Vertical Gradient, has the same properties, Like the second derivative, it does not depend on the locally linear regional anomaly. Moreover, the gradient is less affected by experimental errors.The report gives a practical method of calculating the vertical gradient. Its application is identical to that in general use for calculating the second derivative, except that the numerical coefficients are different. The method also allows the establishment of formulae for downward extension of the field and its derivatives.

Notizen: When, in a two-layer earth, the substratum is insulating or infinitely conducting, the thickness of the top layer can be determined from surface potential measurements along a radius from a single point power electrode. The observed potential needs to be numerically integrated in a direction perpendicular to the said radius, and Figure 4 can then be used to find the thickness. A field example is included.

Notizen: In order to increase the seismic efficiency of the Sparker-system developments were made in 1966/67. Results illustrating the main steps of this development are discussed. A new type of electrode called Transploder electrode was field-tested and proved to be promising.

Notizen: The theory of electrical dipole soundings proved that this method can produce resistivity measurements, which are comparable with those obtained by electrical soundings of the Wenner or Schlumberger type. Their main advantage is the use of short cable lengths, which is important if the depth of penetration should be large.A considerable disadvantage of the dipole method is the great sensitivity to lateral discontinuities. Though these have an influence on the Schlumberger arrangement as well, they can disturb a dipole sounding to such an extent than an interpretation based on a horizontal layer case is no more possible.There are six different dipole arrays, which differ from each other with respect to the angle enclosed by the two dipole orientations-the current dipole AB and the measuring dipole MN. The theoretical comparison of the dipole arrays with the Schlumberger array concerning their sensitivity to lateral discontinuities is a useful basis for the choice of the most suitable configuration.Considering geological subsurface conditions the right choice of a dipole array can give an optimal result, i.e. a dipole sounding for which the sensitivity to lateral discontinuities is as small as possible under the given circumstances.

Notizen: Deconvolution and deringing are well known subjects and it is not necessary to state again their objectives nor the basical methods used to reach them. Let us just remember that, generally, among many others, the two following assumptions are made for simplification purposes:〈list xml:id="l1" style="plain"〉—for deconvolution, it is assumed that the recorded seismic signal is constant, meaning that its shape is the same all along the time interval during which the trace is to be deconvolved;—for de-ringing, it is assumed that the ringing period is constant and that the intensity of the ringing phenomenon is independant of the time.With these two assumptions, a single constant operator can be applied for deconvolving, deringing or both. In most cases, the time variations of the signal or of the ringing are small enough and the error resulting of the application of a constant operator is acceptable. It results into a slight increase of the noise level or into a small residual ringing in the processed trace.When this noise or the residual ringing are too important, the assumption of a constant signal and ringing period must be rejected. This is the case that is examined here according to the following steps:〈list xml:id="l2" style="plain"〉—short definition of the problem;—fast evaluation of some possible solutions;—the selected solution: resulting approximations and how to obviate them, computing method and a remark about the operators;—theoretical example: the efficiency of the process used is evaluated on data in which the results aimed at are known; the influence of the selection of numerical values to be assigned to the parameters is examined;—real cases: comparison of results obtained with the Protee process and with more conventional processes assuming a time invariance or including a weighted composition of several conventional processes each with a different operator.

Notizen: Sharp cut-off frequency filtering is carried out in the discrete time domain on digital computers. A convolution of the digital filter impulse response with the sampled input yields the output. For practical reasons, the length of the filter inpulse response, corresponding to the number of filter coefficients, is limited, and consequently the resulting frequency characteristic will no longer be identical to that originally specified. This is analogous to synthesising some specified frequency characteristic with a finite number of resistive, capacitative and inductive components.In Part I of this paper, we examine the effect of approximating the sharp cut-off frequency characteristic best in a mean square sense by an impulse response of finite length. The resulting frequency characteristic corresponds to the truncated impulse response of the specified frequency characteristic. It has a cut-off slope proportional to, and a mean square error inversely proportional to, the length of the impulse response, and is a biassed odd function about the cut-off frequency point. Because of the Gibbs phenomenon for discontinuous functions, the resulting frequency characteristic will always have a maximum overshoot with respect to the specified characteristic of ± 9%, regardless of the length of the corresponding impulse response. Equal length truncated impulse responses of specified filters with different cut-off frequencies yield frequency characteristics which are almost identical about their respective cut-off points. Now on a log frequency scale (as against a linear frequency scale implied previously) such characteristics may be made almost identical about the respective cut-off points by having the truncated impulse responses composed of an equal number of zero crossings. Results for the low-pass filter are applicable to the high-pass and band-pass characteristics.In the latter case, the mean square error is double that for a single slope characteristic (low-pass or high-pass) and the slopes at both edges of the passband are approximately equal in magnitude to the length of the impulse response (linear frequency scale).Part II of this paper is concerned with reducing the ± 9% overshoot that results from the discontinuous nature of the sharp cut-off frequency characteristic and which is not dependent on the length of the truncated impulse response. The reduction is achieved, at the expense of the steepness of cut-off for the resulting frequency characteristic, by the use of functions which weight the truncated impulse response of the specified frequency characteristic. These functions are called apodising functions. Among other variables, the length of the truncated weighted impulse response will determine the amount of maximum overshoot since the effective frequency characteristic being approximated is no longer a discontinuous function. The digital realization of the finite length impulse responses of Parts I and II is discussed in Part III, together with the optimum partially specified digital filter approximation to the desired frequency characteristic.

Notizen: The purpose of this report is to show a method of determining the top of a refractor departing from the times and slopes of the direct and inverse dromocrones. The method does not need topographical correction and can be applied without knowledge of the distance between the geophone and the shot point.These results having been obtained, the commonly accepted point of view is upset: instead of looking for two points on the surface corresponding to one point of the refractor, we try to etablish, starting with only one point from the surface, the two corresponding points from the top of the refractor.This method can be applied to isolated points and does not demand interpretative hypotheses of any kind, excluding the velocity evaluation of the overburden and of the refractor.The necessary calculations can be easily executed by means of a digital computer to which the dromocrone times and the distances between the geophones must be given. These calculations can also be executed by a person having no knowledge of refraction seismology.This report also examines the validity of the approximations involved in the method proposed.

Notizen: Determining the shape of a pulse generated by an explosion solely from the data provided by the recorded seismic trace is a difficult and even ambitious task.Knowledge of parameters such as length and number of “arches” of the pulse under study is, in fact, indispensable in solving this problem.These parameters cannot be found directly in the seismic trace, which nevertheless contains a great amount of information. Autocorrelation, with its mathematical and statistical properties, is an efficient way of making the best of this information.We compute all the autocorrelations of reflections having a given number of arches which fulfil certain conditions determined in advance. Then, after statistical testing of some parameters pertaining to the autocorrelations (abcissae of zeros, of extrema …), we select only those with a maximum likelihood. It is sufficient to consider only the reflections whose autocorrelations have been selected and to arrange them in groups according to their shape and arch number in order to obtain average pulses.In so doing several solutions are arrived at, but when considering a given number of traces, a single record for instance, it is possible by comparing these results with each other to considerably reduce their number.In the last part of the paper the nature of the impulse obtained with our method is examined in order to find out whether it is “minimum phase” for carrying out deconvolutions.

Notizen: In recent years considerable work has been done to devise a satisfactory non-dynamite seismic system that would replace dynamite in offshore areas. Prior to the advent of digital recording and processing, the non-dynamite sources have generally not provided the depth of penetration or the resolution required for satisfactory seismic interpretation.More recent developments in non-dynamite offshore marine sources include adaptation of the Vibroseis from a land unit to a marine unit, and adaptation of the Dinoseis unit from a land to a marine unit. The SUE (Seismic Underwater Explorer) system is a thermodynamic non-dynamite source utilizing a mixture of propane and oxygen detonated in a special chamber approximately 15 feet below the water surface. This source gives penetration to more than 4 sec in areas typified by Gulf of Mexico type geology and shows deeper penetration than had previously been obtained by dynamite along the western United States in areas with 20 lb charge limitations. A pneumatic source, the airgun, has been in production use in the United States since June 1966. This non-dynamite source provides an intriguing amount of versatility and can be expanded to provide additional energy as necessary to obtain the penetration desired. Tests using systems comprised of from eight to twenty-three airguns show penetration in excess of 5 seconds in many areas. Power spectra comparisons both in amplitude and frequency content demonstrate that this is a controlled source generating a controlled seismic wavelet and a controlled frequency spectrum that can be tailored to fit requirements of particular areas. Sample sections obtained in the Gulf of Mexico and the Pacific Ocean offshore California show adequate penetration to 5.0 seconds reflection time.Quantitative measurements with the airguns demonstrate the effect of:〈list xml:id="l1" style="custom"〉1Variation of the number of guns in the system;2Shaping the frequency spectrum by using different sizes of airguns in the system;3Effects on signal-to-noise ratios as a result of stacking several small energy sources together;4Reproducibility of the initial pulse wavelet from shot to shot.The improvement in record quality as a result of advanced digital processing with non-dynamite sources is comparable to that obtained with dynamite sources. Non-dynamite sources make additional improvements possible where high source multiplicity is advantageous. Excellent dynamic correlations yield accurate velocity control as well as definitions of apparent velocities attributable to multiples and primary-to-multiple amplitude relationships.Non-dynamite sources are being used more and more extensively in offshore exploration. The advent of digital recording and processing provides a means for improving depth of penetration and resolution of many non-dynamite sources.

Notizen: In the region covered by the paper, electrical methods have been applied in four different zones:〈list xml:id="l1" style="custom"〉a) Ales-Maruejols Basin (resistive lower Oligocene blanketed by conductive Upper Oligocene);b) Ledignan and Vaunage-Lunel anticlines (faulted structures in the marly and limy Cretaceous, with different resistivities;c) Camargue (thick series of conductive sediments);d) Beziers Basin (highly complicated structures in the Mesozoic, widely blanketed by conductive Miocene).It may be assumed that electrical methods can yield valuable information enabling one to define the rugged subsurface topography of resistive strata burried under a reasonably thick cover of conductive sediments especially when a part of the lower formation outcrops even if the part exposed be small. Faults may be delineated and much, more information is obtainable than can be expected from gravity meter survey at a price not very much higher.

Notizen: For the treatment of the problems involved in the interpretation of gravity pictures this paper gives a formula that holds generally for any potential function. It provides an extended applicability of the relation used by Elkins for the computation of the second derivative, and also yields an analogous relation to derivatives of higher order of the gravity field.This relation has not been utilized to determine in details the course of the derivatives of higher order in a plane, but is merely applied to points of comparatively extreme curvature of the isogams where the differential values present a ratio favourable to the “noise level”. By this method the values of the derivatives of higher order will not be determined themselves but only the ratio's responsible for the depth of divergence in comparison with the course of an anomaly of masses replaced by points.It is shown by examples of intercalated masses that the divergence points are important and by law related to the form and position of the density contrasts themselves.An analysis of the total gravity picture is made possible by progressing from elements close to the surface to deeper ones. In this way the fundamental features of the earth's crust will be obtained. The application of the analysis process to a gravity anomaly actually measured in Northwest Germany is given.

Notizen: When refraction time signals are transmitted over a radio link between shooter and observer there is a serious risk of interference from electrical storms. This risk can be minimised by sending a series of signals at fixed time intervals and the paper describes a simple device which will do this with the required accuracy.

Notizen: Seismic reflection, telluric and gravity results are given for the lifted area of Ferrara, in Northern Italy. The agreement is shown between the available shallow seismic data and the gravity evidences. For a portion of the above area where seismic results are particularly poor the vertical gradients method gives a resolution of a gravity anomaly and confirms the telluric information. The residual gravity values, the vertical gradients and the telluric data along a seismic line crossing the zone are compared with seismic results and with evidences from adjacent wells.

Notizen: Investigations into reflection seismic on the salt structure of Heide raised the following questions:〈list xml:id="l1" style="custom"〉1) How can the different directions of trend of a series of layers be established?2) How are the contour maps of reflecting horizons to be constructed if there is no general trend of the layers?To answer these questions, the case of the subsoil consisting of a series of layers with plane reflecting beds and constant layer-velocities is treated strictly. The strike lines of the reflecting planes may be at any angle whatever. However, formulas for constructing contour maps of the reflecting planes have been derived. With these formulas, the problem quoted under 1) has also been solved.The construction of contour maps is given.For special cases, formulas are obtained which have already been proved by others.

Notizen: The triple integral for the attraction of a mass on a point is transformed in a double sum. This double sum serves to construct a graph for the rapid determination of the gravimetric influence of structures given by depth contours. The influence of topography can also be computed with this graph.