ALBERT

Description: Projections of technological advances to the year 2000 have suggested a number of possible conceptual types of air vehicles. For convenience, these have been grouped according to speed, increasing from below Mach 1 (including hovering flight) through various Mach ranges to orbital flight. The potential performance capabilities that could be realized for each of these types of aircraft provide exciting prospects for the years beyond 2000. It is clear that the greater design flexibilities provided by the projected technology advances will permit significant improvements in performance, economy, and safety and allow the design and development of aircraft systems that current technology will not support. In the following sections, each vehicle type is discussed, noting design features and significant advances. Where related aircraft exist, the significant economic and performance factors are compared. In addition, for each concept, the technology developments considered essential for the advanced concept are identified. The types of aircraft described are examples of what advances in the technology projected for the year 2000 could provide. They are by no means all that would be possible. The panel's views on the current state of knowledge of systems intergration as a discipline and the need for advancement in this area presented in the concluding section of this report.

Description: Over the last 50 years, aeronautical structures have evolved from the wood, fabric, and wire of low-speed biplanes to supersonic aircraft fabricated with advanced metallic and nonmetallic materials. The advances made in structures technology have had significant impact on aircraft design and performance. An example is the large weight reductions being realized from the utilization of composite materials for secondary and primary structures. However, structural advances have been evolutionary, not revolutionary. Through the year 2000, there are opportunities to obtain significant new advancements in structural technology. These advances could result in considerable performance and capability payoffs such as increased payload, range, speed, maneuverability, fuel efficiency, and safety through reductions in weight, increases in strength, and the ability to make structures pliable. Also, with new manufacturing processes it is possible that reductions in production costs will be realized. Some of the structural technology areas where future major advances could be made are adaptive structures, thermal structures, damage tolerant structures, propulsion system structures, and new structural concepts.

Description: A cascade of 65-(12)10 compressor blades was tested at one geometric setting over a range of inlet Mach number from 0.12 to 0.89. Two groups of data are presented and compared: the first from the cascade operating conventionally with no boundary-layer control, and the second with the boundary layer controlled by a combination of upstream slot suction and porous-wall suction at the blade tips. A criterion for two-dimensionality was used to specify the degree of boundary-layer control by suction to be applied. The data are presented and an analysis is made to show the effect of Mach number on turning angle, blade wake, pressure distribution about the blade profile and static-pressure rise. The influence of boundary-layer control on these parameters as well as on the secondary losses is illustrated. A system of correlating the measured static-pressure rise through the cascade with the theoretical isentropic values is presented which gives good agreement with the data. The pressure distribution about the blade profile for an inlet Mach number of 0.21 is corrected with the Prandtl-Glauert, Karman-Tsien, and vector-mean velocity - contraction coefficient compressibility correction factors to inlet Mach numbers of 0.6 and 0.7. The resulting curves are compared with the experimental pressure distributions for inlet Mach numbers of 0.6 and 0.7 so that the validity of applying the three corrections can be evaluated.

Description: The stator-blade angles in the twelfth through fifteenth stages of a 16-stage axial-flow compressor were increased 3O. The over-all performance of this modified compressor is compared to the performance of the compressor with original blade angles. The matching characteristics of the modified compressor and a two-stage turbine were obtained and compared to those of the compressor with original blade angles and the same turbine.

Description: After studying three Tech Briefs reports on NASA submerged duct technology developed for high performance aircraft, Wilhelm Cashen was able to adapt the technology to the induction intercooler system of turbocharged lightplanes. In lightplane installations, the submerged ducts introduce cool "ram" air to the propulsion system for greater operating efficiency.

Description: An impulse-momentum method for determining impact conditions for landing gears in eccentric landings is presented. The analysis is primarily concerned with the determination of contact velocities for impacts subsequent to initial touchdown in eccentric landings and with the determination of the effective mass acting on each landing gear. These parameters determine the energy-absorption requirements for the landing gear and, in conjunction with the particular characteristics of the landing gear, govern the magnitude of the ground loads. Changes in airplane angular and linear velocities and the magnitude of landing-gear vertical, drag, and side impulses resulting from a landing impact are determined by means of impulse-momentum relationships without the necessity for considering detailed force-time variations. The effective mass acting on each gear is also determined from the calculated landing-gear impulses. General equations applicable to any type of eccentric landing are written and solutions are obtained for the particular cases of an impact on one gear, a simultaneous impact on any two gears, and a symmetrical impact. In addition a solution is presented for a simplified two-degree-of-freedom system which allows rapid qualitative evaluation of the effects of certain principal parameters. The general analysis permits evaluation of the importance of such initial conditions at ground contact as vertical, horizontal, and side drift velocities, wing lift, roll and pitch angles, and rolling and pitching velocities, as well as the effects of such factors as landing gear location, airplane inertia, landing-gear length, energy-absorption efficiency, and wheel angular inertia on the severity of landing impacts. -A brief supplementary study which permits a limited evaluation of variable aerodynamic effects neglected in the analysis is presented in the appendix. Application of the analysis indicates that landing-gear impacts in eccentric landings can be appreciably more severe than impacts in symmetrical landings with the same sinking speed. The results also indicate the effects of landing-gear location, airplane inertia, initial wing lift, side drift velocity, attitude, and initial rolling velocity on the severity of both initial and subsequent landing-gear impacts. A comparison of the severity of impacts on auxiliary gears for tricycle and quadricycle configurations is also presented.

Description: An elementary type of analysis has been used to determine the amount of wing tip that must be severed to produce irrevocable loss of control of a B-29 airplane. The remaining inboard structure of the Boeing B-29 wing has then been analyzed and curves are presented for the estimated reduction in structural strength due to four general types of damage produced by rod-type warhead fragments. The curves indicate the extent of structural damage required to produce a kill of the aircraft within 10 seconds.

Description: The results of studies conducted over the last 15 years to assess missions and vehicle concepts for modern, propelled, lighter-than-air vehicles (airships) were surveyed. Rigid and non-rigid airship concepts are considered. The use of airships for ocean patrol and surveillance is discussed along with vertical heavy lift airships. Military and civilian needs for high altitude platforms are addressed. Around 1970 a resurgence of interest about lighter-than-air vehicles (airships) occurred in both the public at large and in certain isolated elements of the aerospace industry. Such renewals of airship enthusiasm are not new and have, in fact, occurred regularly since the days of the Hindenburg and other large rigid airships. However, the interest that developed in the early 1970's has been particularly strong and self-sustaining for a number of good reasons. The first is the rapid increase in fuel prices over the last decade and the common belief (usually true) that airships are the most fuel efficient means of air transportation. Second, a number of new mission needs have arisen, particularly in surveillance and patrol and in vertical heavy-lift, which would seem to be well-suited to airship capabilities. The third reason is the recent proposal of many new and innovative airship concepts. Finally, there is the prospect of adapting to airships the tremendous amount of new aeronautical technology which has been developed in the past few decades thereby obtaining dramatic new airship capabilities. The primary purpose of this volume is to survey the results of studies, conducted over the last 15 years, to assess missions and vehicle concepts for modern propelled lighter-than-air vehicles.

Description: Discrete attitude commands have become a standard task for flying qualities evaluation and control system testing. Much pilot opinion data is now available for ground-based and in-flight simulations, but adequate performance measures and prediction methods have not been established. The Step Target Tracking Prediction method, introduced in 1978, correlated time-on-target and rms tracking data with NT-33 in-flight longitudinal simulations, but did not employ parameters easily measured in manned flight and simulation. Recent application of the Step Target Tracking Prediction method to lateral flying qualities analysis has led to a new measure of performance. This quantity, called Maximum Normalized Rate (MNR), reflects the greatest attitude rate a pilot can employ during a discrete maneuver without excessive overshoot and oscillation. MNR correlates NT-33 lateral pilot opinion ratings well, and is easily measured during night test or simulation. Furthermore, the Step Target MNR method can be used to analyze large amplitude problems concerning rate limiting and nonlinear aerodynamics.

Description: As part of a program to determine the feasibility of using a fighter airplane as a parasite in combination with a Consolidated Vultee RB-36 for long-range reconnaissance missions (project FICON), an experimental investigation has been made in the Langley free-flight tunnel to determine the dynamic stability and control characteristics of a 1/17.5-scale model of a Chance Vought F7U-3 airplane in several tow configurations. The investigation consisted of flight tests in which the model was towed from a strut in the tunnel by a towline and by a direct coupling which provided complete angular freedom. The tests with the direct coupling also included a study of the effect of spring restraint in roll in order to simulate approximately the proposed full-scale arrangement in which the only freedom is that permitted by the flexibility of the launching and retrieving trapeze carried by the-bomber. For the tow configurations in which a towline was used (15 and 38 feet full scale), the model had a very unstable lateral oscillation which could not be controlled. The stability was also unsatisfactory for the tow configuration in Which the model was coupled directly to the strut with complete angular freedom. When spring restraint in roll was added, however, the stability was satisfactory. The use of the yaw damper which increased the damping in yaw to about six times the normal value of the model appeared to have no appreciable effect on the lateral oscillations in the towline configurations, but produced a slight improvement in the case of the direct coupling configurations. The longitudinal stability was satisfactory for those cases in which the lateral stability was good enough to permit study of longitudinal motions.

Description: Tests have been made at the Langley Aeronautical Laboratory on a 6000-horsepower propeller dynamometer installed at a ground test facility to determine the effect of a half-scale model of the Wright Aeronautical Development Center 30,000-horsepower whirl rig upon the aerodynamic characteristics of a three-blade NACA 10-(3)(062)-045 propeller. The model of the whirl rig was mounted in front of the 6000-horsepower propeller dynamometer. Static propeller tests were made for 0deg, 5deg, 10deg, 15deg, and 20deg blade angles over a range of rotational speeds from 600 to 2200 rpm in 100-rpm increments. Measurements were made of propeller thrust and torque, stresses in the propeller blades, and static and total pressures over the surface of the model. Propeller thrust and torque were increased up to 33 percent by the presence of the model of the whirl rig, but the average increase was from 5 to 10 percent. Blade vibratory stresses were small.

Description: The aerodynamic characteristics in pitch of the Army Ordnance Corps T205 3.5-inch HEAT rocket with various head designs and one fin modification have been determined at velocities of 500, 700 and 900 feet per second in the Langley high-speed 7- by 10-foot tunnel. The results presented are those of the full-scale model. Comparison of results obtained at 500 feet per second shows, in general, that for changes on the forward portion of the head the missile configurations having the greatest stability - most rearward center-of-loads location - were those having the highest drag. However, very limited comparisons indicate that the shape of the rear position of the head may be an important factor in reducing the drag and increasing the restoring moments. Generally, large increases in drag were noted for the various head designs with an increase in Mach number from 0.62 to 0.82. Pitching-moment-curve slopes increased with Mach number on all models except those having reasonably well-faired forward sections. These models showed a decrease in stability with increases in Mach number.

Description: Preliminary results of one phase of a control-motion study program are presented in the form of plots of load factor.and angular acceleration against indicated airspeed and of time histories of several measured quantities. The results were obtained from 197 maneuvers performed by an F-86A jet-fighter airplane during normal squadron operational training. Most of the tactical maneuver8 of which the F-86A is capable were performed at pressure altitudes ranging from 0 to 32,000 feet and at indicated airspeeds ranging from 95 to 650 miles per hour.

Description: Force characteristics determined from tank tests of a 1/5.78 scale model of a hydro-ski-wheel combination for the Grumman JRF-5 airplane are presented. The model was tested in both the submerged and planing conditions over a range of trim, speed, and load sufficiently large to represent the most probable full-size conditions.

Description: Preliminary performance analysis and conceptual design are described for a class of unmanned airplanes possessing multi-day endurance capability. A mixed-mode electric power system incorporates solar cells for daytime energy production and a non-regenerative H2-02 fuel cell to supply energy for night flight. The power system provides energy for all onboard systems, including propulsion., payload, and avionics. Excess solar energy is available during significant portions of the day, and may be used for climbing, maneuvering, or payload functions. By jettisoning fuel cell reactant product (water) during flight, vehicle endurance may be increased under certain conditions. Empirical structure sizing algorithms are combined with low-Reynolds number aerodynamics algorithms to estimate airplane size and geometry to meet prescribed mission requirements. Initial calculations for summertime, high-altitude flight (above 40,000 ft (12 km)) at moderate latitude (31 deg N) indicate that mission endurance of several days may be possible for configurations having wing loadings on the order of 0.9 to 1.3 lb/ft(exp 2). These aircraft tend to be somewhat smaller than solar-powered aircraft previously conceived for multi-month endurance utilizing regenerative fuel cell systems for night flight.

Description: An investigation was conducted in the Ames 12-foot pressure wind tunnel to determine the effect of an operating propeller on the aerodynamic characteristics of a l/l9-scale model of the Lockheed XFV-1 airplane, Several full-scale power conditions were simulated at Mach numbers from 0.50 to 0.92; the.Reynolds number was constant at 1,7 million. Lift, longitudinal force, pitch, roll, and yaw characteristics, determined with and without power, are presented for the complete model and for various combinations of model components, Results of an investigation to determine the characteristics of the dual-rotating propeller used on the model are given also,

Description: The stator-blade angles in the first four stages of a 16-stage axial-flow compressor were increased in order to decrease the angles of attack of these stages, and thereby to improve part-speed performance. The performance of this modified compressor was compared with that of the same compressor with original blade angles.