ALBERT

Description: Several groups of new airfoil sections, designated as the NACA 8-series, are derived analytically to have lift characteristics at supercritical Mach numbers which are favorable in the sense that the abrupt loss of lift, characteristic of the usual airfoil section at Mach numbers above the critical, is avoided. Aerodynamic characteristics determined, from two-dimensional windtunnel tests at Mach numbers up to approximately 0.9 are presented for each of the derived airfoils. Comparisons are made between the characteristics of these airfoils and the corresponding characteristics of representative NPiCA 6-series airfoils. The experimental results confirm the design expectations in demonstrating for the NACA S-series airfoils either no variation, or an Increase from the low-speed design value, In the lift coefficient at a constant angle of attack with increasing Mach number above the critical. It was not found possible to improve the variation with Mach number of the slope of the lift curve for these airfoils above that for the NACA 6-series airfoils. The drag characteristics of the new airfoils are somewhat inferior to those of the NACA 6- series with respect to divergence with Mach number, but the pitching-moment characteristics are more favorable for the thinner new sections In demonstrating somewhat smaller variations of moment coefficient with both angle of attack and Mach number. The effect on the aero&ynamic characteristics at high Mach numbers of removing the cusp from the trailing-edge regions of two 10-percent-chord-thick NACA 6-series airfoils is determined to be negligible.

Description: A 1/5-scale model of the Republic x-84 airplane (Army Project MX-578) was tested in the Langley 300 MPH 7- by 10-foot tunnel. The primary object of the tests was twofold: to determine, a practicable method of increasing the longitudinal 3tability in the landing configuration, and to investigate the effects on longitudinal and lateral Stability of various external stored (fuel tanks, bombs, and rockets). The effects of the fuselage dive brakes were also determined, and the critical Mach numbers of certain of the airplane components were estimated. The use of the revised horizontal tail (of larger aspect ratio and area than the original) seemed to be the most feasible expedient for materially increasing the longitudinal stability in the landing configuration. The neutral-point shifts produced by the various external stores were unstable, the largest shift being about 2.5 percent mean aerodynamic chord. No appreciable aerodynamic trim changes were caused by the external stores. From the standpoint of range, maximum s peed, and rate of climb, the advantages of mounting the fuel tanks at the wing tips rather than inboard beneath the wings were clearly demonstrated by the tests. The effective dihedral parameter was the only static lateral-stability derivative appreciably affected by the external stores. At high lift coefficients, the tip-mounted tanks caused a large increase in the effective dihedral parameter (about 40 increase at a lift coefficient of 1.0). This increase was held undesirable, because the tendency toward oscillatory instability that it would cause would be heightened by the increased moments of inertia resulting from the weight of the tanks when carrying fuel. The fuselage dive brakes, when deflected, caused a change in trim tending to nose the airplane up; the neutral point also moved rearward upon deflecting the dive brakes. The amount of elevator required to overcome the change in trim was well within the available range of deflection. It was estimated that a drive-brake deflection of 900 would.decrease the terminal Mach number in a vertical dive by about 0.1. The estimated critical Mach number of the V-front canopy was about 0.04 greater than that of the original canopy. Pressure-distribution tests disclosed severe pressure peaks inside the nose of the jet entrance duct. These peaks, which would lead to separation and consequently poor pressure recovery at, the engine, could be reduced by, using a smaller nose,radius and: a modified internal lip shape

Description: An investigation of a 1/7-scale powered model of the Kaiser Fleetwing all-wing airplane was made in the Langley full-scale tunnel to provide data for an estimation of the flying qualities of the airplane. The analysis of the stability and control characteristics of the airplane has been made as closely as possible in accordance with the requirements of the Bureau of Aeronautics, Navy Department's specifications, and a summary of the more significant conclusions is presented as follows. With the normal center of gravity located at 20 percent of the mean aerodynamic chord, the airplane will have adequate static longitudinal stability, elevator fixed, for all flight conditions except for low-power operation at low speeds where the stability will be about neutral. There will not be sufficient down-elevator deflection available for trim above speeds of about 130 miles per hour. It is probable that the reduction in the up-elevator deflections required for trim will be accompanied by reduced elevator hinge moments for low-power operation at low flight speeds. The static directional stability for this airplane will be low for all rudder-fixed or rudder-free flight conditions. The maximum rudder deflection of 30 deg will trim only about 15 deg yaw for most flight conditions and only 10 deg yaw for the condition with low power at low speeds. Also, at low powers and low speeds, it is estimated that the rudders will not trim the total adverse yaw resulting from an abrupt aileron roll using maximum aileron deflection. The airplane will meet the requirements for stability and control for asymmetric power operation with one outboard engine inoperative. The airplane would have no tendency for directional divergence but would probably be spirally unstable, with rudders fixed. The static lateral stability of the airplane will probably be about neutral for the high-speed flight conditions and will be only slightly increased for the low-power operation in low-speed flight. The airplane will not roll against the ailerons in a side-slip maneuver. Although the airplane would probably meet the minimum requirements of pb/2V of 0.07 at all speeds, there will be a loss in rolling ability of the airplane at high aileron deflections and at low flight speeds. It is estimated that the wing stall will be a gradual movement forward from the trailing edge and will be accompanied by no sudden pitching or rolling accelerations. Some stall warning may be indicated by reduction in the elevator and aileron force gradients and by the shaking of the controls caused by unsteady flow over the surfaces near the stall.

Description: An investigation has been conducted in the Langley 20-foot free-spinning tunnel to determine the effects of decreasing the rudder deflection, of decreasing the rudder span, and of differential rudder movements on the spin and recovery characteristics of a 0.057-scale model of the Chance Vought XF7U-1 airplane. The results indicated that decreasing the rudder span or the rudder deflections, individually or jointly, did not seriously alter the spin or recovery characteristics of the model; and recovery by normal use of controls (full rapid rudder reversal followed l/2 to 1 turn later by movement of the stick forward of neutral) remained satisfactory. Linking the original rudders so that the inboard rudder moves from full with the spin to neutral while the outboard rudder moves from neutral to full against the spin will also result in satisfactory spin and recovery characteristics. Calculations of rudder-pedal forces for recovery showed that the expected forces would probably be within the capabilities of a pilot but that it would be advisable to install some type of boost in the control system to insure easy and rapid movement of the rudders.

Description: A series of flight tests have been made at the Langley Flight Research Division at the request of the Bureau of Aeronautics, Department of the Navy, to determine the flying qualities of the Grumman F8F-1 air- plane. This paper presents the test results necessary to determine the longitudinal stability and control characteristics end the stalling characteristics. These tests were made between February and June of 1947- The range of Mach numbers covered in this investigation was approximately 0.10 to 0.62, and no attempt was made to investigate compressibility effects at higher Mach numbers. The lateral and directional stability and control characteristics of the subject airplane have already been reported (reference 1). Also presented in this paper is a discussion of the normal accelerations induced by yawing velocity and sideslip which were considered ob,jectionable by the pilot for this airplane. A discussion of the undesirable accelerations has been included with a view towards formulating some flying-qualities requirements limiting them.

Description: A spin investigation has been conducted in the Langley 20-foot free-spinning tunnel on a 1/24-scale model of the North American XP-86 airplane. The effects of control settings and movements upon the erect and inverted spin and recovery characteristics of the model were determined for the design gross weight loading. The long-range loading was also investigated and the effects of extending slats and dive flaps were determined. In addition, the investigation included the determination of the size of spin-recovery parachute required for emergency recovery from demonstration spins, the rudder force required to move the rudder for recovery, and the best method for the pilot to escape if it should become necessary to do so during a spin. The results of the investigation indicated that the XP-86 airplane will probably recover satisfactorily from erect and inverted spins for all possible loadings. It was found that fully extending both slats would be beneficial but that extending the dive brakes would cause unsatisfactory recoveries. It was determined that a 10.0-foot-diameter tail parachute with a drag coefficient of 0.7 and with a towline 30.0 feet long attached below the jet exit or a 6.0-foot-diameter wingtip parachute opened on the outer wing tip with a towline 6.0 feet long would insure recoveries from any spins obtainable. The rudder-pedal force necessary to move the rudder for satisfactory recovery was found to be within the physical capabilities of the pilot.

Description: This paper presents the results of measurements of longitudinal stability of a 1/50-scale model of the XP-88 airplane by the wing-flow method. Lift, rolling-moment, hinge-moment, and pitching-moment characteristics as well as the downwash at the tail were measured over a Mach number range from approximately 0.5 to 1.05 at Reynolds numbers below 1,000,000. No measurements of drag were obtained. No abrupt changes due to Mach number were noted in any of the parameters measured. The data indicated that the wing was subject to early tip stalling; that the tail effectiveness decreased gradually with increasing Mach number up to M = 0.9, but increased again at higher Mach numbers; that the variation of downwash with angle of attack did not change appreciably with Mach number except between 0.95 and 1.0 where d(epsilon)/d(alpha), decreased from 0.46 to 0.32; that at zero lift with a stabilizer setting of -1.5 deg there was a gradually increasing nosing-up tendency with increasing Mach number; and that the control-fixed stability in maneuvers at constant speed gradually increased with increasing Mach number.

Description: An investigation of the spin and recovery characteristics of a 0.057-scale model of the Chance Vought XF7U-1 airplane has been conducted in the Langley 20-foot free-spinning tunnel. The effects of control settings and movements on the erect and inverted spin and recovery characteristics were determined, as were also the effects of extending the wing slats, of center-of-gravity movement, and-of variation in the mass distribution. The investigation also included wing-tip spin-recovery-parachute tests, pilot-escape tests, and rudder-control-force tests. The investigation indicated that the spin and recovery characteristics of the airplane will be satisfactory for all conditions. It was found that a single 4.24-foot (full-scale) parachute when opened alone from the outboard wing tip or two 8.77-foot (full-scale) parachutes when opened simultaneously, one from each wing tip, would effect satisfactory emergency recoveries (the drag coefficients of the parachutes, based on the surface area of the parachute, were 0.83 and 0.70 for the 4.24- and 8.77-foot parachutes, respectively). The towline length in both cases was 25 feet (full scale). Tests results showed that, if the pilot should have to leave the airplane during a spin, he should jump from the outboard side (left side in a right spin) of the cockpit. The rudder-control force necessary for recovery from a spin was found to be rather high but appeared to be within the upper limits of a pilot's capabilities.

Description: Tests of a 1/20-scale dynamically similar model of the Northrop B-35 airplane were made to study its ditching characteristics. The model was ditched in calm water at the Langley tank no. 2 monorail. Various landing attitudes, speeds,and conditions of damage were simulated during the investigation. The ditching characteristics were determined by visual observation and from motion-picture records and time-history acceleration records. Both longitudinal and lateral accelerations were measured. Results are given in tabular form and time-history acceleration curves and sequence photographs are presented. Conclusions based on the model investigation are as follows: 1. The best ditching of the B-35 airplane probably can be made by contacting the water in a near normal landing attitude of about 9 deg with the landing flaps full down so as to have a low horizontal speed. 2. The airplane usually will turn or yaw but the motion will not be violent. The maximum lateral acceleration will be about 2g. 3. If the airplane does not turn or yaw immediately after landing, it probably will trim up and then make a smooth run or porpoise slightly. The maximum longitudinal decelerations that will be encountered are about 6g or 7g. 4. Although the decelerations are not indicated to be especially large, the construction of the airplane is such that extensive damage is to be expected, and it probably will be difficult to find ditching stations where crew members can adequately brace themselves and be reasonably sure of avoiding a large inrush of water.

Description: A flight test was conducted at the Flight Test Station of the Pilotless Aircraft Research Division at Wallops Island, Va., to determine the longitudinal control and stability characteristics of a 0.5-scale model of the Fairchild Lerk Pilotless aircraft with the horizontal wing flaps deflected 15 degrees. The data were obtained by the use of a telemeter and also by radar tracking. The results show an increase of effectiveness of the longitudinal control in producing normal accelerations up to a Mach number of 0.75 where this effectiveness gradually decreased becoming negative at a Mach number of 0.89. Previous tests with wing flaps undeflected an increase in effectiveness up to Mach number of 0.93 where a sudden loss of control occurred. The model was dynamically stable throughout the speed range. The data confirmed the drag increase at the critical Mach number for large angles of attack is indicated in high-speed wind-tunnel tests.

Description: A 1/7 scale semispan model of the XB-35 airplane was tested in the Langley 10 foot pressure tunnel, primarily for the purpose of investigating the effectiveness of a leading-edge slot for alleviation of stick-fixed longitudinal instability at high angles of attack caused by early tip stalling and a device for relief of stick-free instability caused by elevon up-floating tendencies at high angles of attack. Results indicated that the slot was not adequate to provide the desired improvement in stick-fixed stability. The tab-flipper device provided improvement in stick-free stability abd two of the linkage combinations tested gave satisfactory variations of control force with airspeed for all conditions except that in which the wing-tip "pitch-control" flap was fully deflected. However, the improvement in control force characteristics was accompanied by a detrimental effect on stick-fixed stability because of the pitching moments produced by the elevon tab deflection.

Description: At the request of the Henschel Aircraft Works. A. G. Berlin. three models of the missile "Zitterrochen" were investigated at subsonic velocities.(open jet 215-millimeter diameter) and at supersonic velocities (open jet 110 by 130 millimeters) in order to determine the effect of various wing forms on the air forces and moments. Three-component measurements were taken, and one model was also investigated with deflected control plates.

Description: The compression plane is intended for operation on or close to the surface of the water, and has a hull with a concave bottom which forms the upper surface of a tunnel into which air is forced under pressure to support part of the load. The results of the tests made in Langley tank no. 1 include values of the horizontal forces, trimming moment, and static pressure in the tunnel for a wide range of loads and speeds and two power conditions, and are presented in the form of curves against speed with load as a parameter. The results are scaled up to 10 times the model size for three conditions at which the model is self-propelled at a steady speed. Lift is obtained from the static pressure of air in the tunnel. In general, the ratio of the gross load to the total resistance increases with increase in load and decrease in speed. This ratio varies between l-7 and 5.7 at high speeds and has a maximum value of 7. The total resistance is nearly the same for both power conditions except at low speeds and heavy loads. No abrupt change in forces on the hull or flow around the hull occurs in. the region of zero draft. The centers of pressure are generally far aft. At the most efficient trim (1.2'), considerable bow-up moment would be required for practicable operation. There is no abrupt transition from the air-borne to the water- borne condition.

Description: Flight tests have been made to determine the longitudinal stability and control and stalling characteristics of a North American P-51H airplane. The results indicate that the airplane has satisfactory longitudinal stability in all the flight conditions tested at normal loadings up to 25,000 feet altitude. At Mach numbers above 0.7, the elevator push force required for longitudinal trim decreased somewhat because of compressibility effects. The elevator stick force per g in accelerated turns at the forward center-of-gravity position of 24 percent mean aerodynamic chord above 250 miles per hour was in excess of the required limits at both 5,000 and 25,OOO feet altitude. The longitudinal-trim-force changes due to flaps and power were small, but the rudder-trim-force change with power change was high. The stalling characteristics in all the conditions tested were satisfactory.

Description: The ditching characteristics of the Lockheed XR60-1 airplane were determined by tests of a 1/24-scale dynamic model in calm water at the Langley tank no. 2 monorail. Various landing attitudes, flap settings, speeds, and conditions of damager were investigated. The ditching behavior was evaluated from recordings of decelerations, length of runs, and motions of the model. Scale-strength bottoms and simulated crumpled bottoms were used to reproduce probable damage to the fuselage. It was concluded that the airplane should be ditched at a landing attitude of about 5 deg with flaps full down. At this attitude, the maximum longitudinal deceleration should not exceed 2g and the landing run will be bout three fuselage lengths. Damage to the fuselage will not be excessive and will be greatest near the point of initial contact with the water.

Description: Spin tests have been performed in the Langley 20-foot free-spinning tunnel on a 1/18-scale model of the Fairchild XNQ-1 airplane. The spin and recovery characteristics of the model were determined for the normal gross-weight loading and for two variations from this loading - center of gravity moved rearward and relative mass distribution increased along the fuselage. These tests were performed for two vertical-tail plan forms. The investigation also included simulated pilot-escape tests and rudder-force tests. The recovery characteristics of the model were satisfactory for all conditions tested by full reversal of the rudder and by simultaneous neutralization of the rudder and elevator. It was indicated that if necessary to escape from the spinning airplane, the pilot should jump from the outboard side of the fuselage and as far rearward as possible. Aa determined from spin model tests, the rudder pedal force required to reverse the rudder for recovery from the spin will be light.

Description: This report presents the results of an investigation in the transonic speed range of the longitudinal stability characteristics of a proposed configuration for the Republic XF-91 airplane. The tests covered a Mach number range of 0.55 to 1.05 and a Reynolds number range from 400,000 to 1,375,000. Lift, pitching-moment, and rolling-moment characteristics of the half model and the hinge moments on the all-moving tail were measured. The downwash factor delta x epsilon / delta x alpha at the tail was determined from the pitching-moment data. A calculation of the elevator deflection and stick force required for trim was also made. It was found that the variation of force and moment coefficients was linear through the test angle-of-attack range of -1 deg to 8 deg at any Mach number; that the stability increased markedly at Mach numbers above 0.85; that the effectiveness of the tail in producing pitching moments decreased about one-third with increasing Mach numbers and that the value of the downwash factor, delta x epsilon / delta x alpha, at the tail decreased from about 0.35 at a Mach number of 0.85 to about zero at a Mach number near 0.95 and became slightly negative at higher Mach numbers. The calculated values of stick force per g and elevator deflection per g, assuming no aerodynamic balance, increased rapidly above a Mach number of 0.85.

Description: Based on results of longitudinal trim and tumble tests of a 0.057-scale model of the Chance Vought XF7U-1 airplane, the following conclusions regarding the trim and tumble characteristics of the airplane have been drawn: 1. The airplane will not trim at any unusual or uncontrolled angles of attack. 2. The airplane will not tumble with the center of gravity located forward of 24 percent of the mean aerodynamic chord. When the center of gravity is located at 24 percent of the mean aerodynamic chord and slats are extended and elevators are deflected full up, the airplane may tumble if given an external positive pitching moment. 3. The tumbling motion obtained will be readily terminated by deflecting the elevators full down so as to oppose the rotation. 4. The accelerations encountered during an established tumble may be dangerous to the pilot and, therefore, action should be taken to terminate a tumble immediately upon its inception. 5. Simultaneous opening of two wing-tip parachutes having diameters of 4 feet or larger and having drag coefficients of approximately 0.7 will effectively terminate the tumble. 6. Model results indicate that the pilot will not be struck by the airplane if it becomes necessary to leave the airplane during a tumble. The pilot may require aid from an ejection-seat arrangement.

Description: At the request of the Bureau of Aeronautics, Navy Department, a stability and control investigation of a 1/10-scale model of the Chance Vought XF7U-1 airplane has been conducted in the Langley free-flight tunnel. Results of force end flight tests to determine the power-off stability and control characteristics of the model with slats retracted and extended are presented herein. The longitudinal and lateral stability characteristics were satisfactory for both the slats retracted and extended conditions over the lift range up to the stall. With the slats retracted, the stall was fairly gentle but the model rolled off out of control. With the slats extended, control could be maintained at the stall so that the wings could be kept level even as the model dropped.

Description: An investigation of the spin and recovery characteristics of a scale model of the Grumman XF9F-2 airplane has been conducted in the Langley 20-foot free-spinning tunnel. The effects of control settings and movements on the erect and inverted spin and recovery characteristics of the model in the flight loading were determined. The investigation also included spin-recovery-parachute, pilot-escape, and rudder-pedal- . force tests. The recovery characteristics of the model were satisfactory for all configurations tested. Spins for the normal control configuration were oscillatory in roll and yaw. Deflecting the leading-edge flaps or the dive brakes did not change the spin and recovery characteristics of the model noticeably. A 10.0-foot tail parachute or a 6.0-foot wing-tip parachute (drag coefficient of 0.75) was found to be effective for recoveries from demonstration spins. The rudder forces in the spin appeared to be within the capabilities of the pilot.

Description: The ditching characteristics of the Army B-36 airplane were determined by testing 1/20- and 1/30-scale dynamic models in calm water in Langley tank no. 2 and at the outdoor catapult. The scope of the tests consisted of ditching the models at various conditions of simulated damage, landing attitudes, and speeds, with various flap settings using several degrees of restraint of the flap hinges. The ditching behavior was evaluated from recordings of deceleration, length of run, and motions of the models. The results showed that the airplane should be ditched at an attitude of about 9 deg with flaps full down. The probable ditching behavior will be a smooth run with a maximum longitudinal deceleration of 3g to 4g and a landing run of 4 to 5 fuselage lengths. Structural failure of the underside of the fuselage will not seriously affect the behavior of the airplane.

Description: An investigation has been conducted in the Langley 20-foot free-spinning tunnel on the 1/20-scale model of the Chance Vought XF6U-1 airplane altered to represent the XF6U-1 airplane as it will be spin-tested in flight, and also altered to represent the F6U-1 airplane as it will be produced for service use. Spin tests were made to determine the effects of control settings and movements at the normal loading. The results show that the spins obtained on the revised XF6U-1 airplane will be oscillatory in roll and yaw and that recoveries by rudder reversal will be rapid. Model test results indicate that the F6U-1 airplane will probably not spin. Inasmuch as the results of this investigation show that the new designs are as good as or better than the original XF6U-1 design in regard to spin recovery, it is felt that the conclusions and recommendations reached for the original design can be applied to the new designs for all loading conditions.

Description: In.order to determine the aerodynamic effects of an auxiliary belly fuel tank on the Grumman F8F-1 airplane, a wind-tunnel investigation was made on a l/5 - scale model of the Grumman XF8F-1 airplane. Pitch and yaw tests were made with the model in the cruising and landing configurations for windmilling and take-off power conditions. Tuft studies and static-pressure measurements were also made to determine the flow characteristics in the region of the fuel tank. It was found that, at low speed, the auxiliary fuel tank test conditions, especially with power on in the landing configuration at high lift coefficients. The static directional stability was decreased for most test conditions, but the addition of a fairing between the fuselage and fuel tank improved the directional stability slightly in the power-on clean condition. The effective dihedral and lateral force were increased for most of the conditions tested. The tuft studies and pressure measurements indicated that the removal of the away braces would improve the.flow characteristics considerably in the region of the fuel tank end might also decrease the buffeting of the belly tank at high speeds.

Description: Tests of a model of the XJR2F-Y amphibian were made in Langley tank no. to determine the spray characteristics and the take-off and landing stability. At a gross load of 22,000 pounds full size, spray entered the propeller disk only at a very narrow range of speeds. The spray striking the flaps was not excessive and no appreciable wetting of the tail surfaces was noted. The trim limits of stability appeared to be satisfactory and the upper-limit porpoising was not violent. The stable range of center-of-gravity locations with flaps set 20deg was well aft of the desired operating range. However, with flaps up, the forward limit was about 18 percent mean aerodynamic chord and the aft limit about 28.5 percent mean aerodynamic chord at a load of 26,000 pounds and with elevators deflected -10deg. Under these conditions the location of the step is considered satisfactory. Tests showed that the effect of water in the nose-wheel well would be to move the forward limit aft about 2-percent mean aerodynamic chord. Without ventilation of the main step, the model skipped during landing at most trims, but this skipping was not violent. With the ventilation, the model skipped lightly only at trims where the afterbody keel was approximately parallel to the water (around 7.5 deg).

Description: The gust and draft velocities from records of NACA instruments installed in P-61C airplanes participating in thunderstorm flights at Clinton County Army Air Field, Ohio, from September 10, 1947 to September 15, 1947, are presented.

Description: A high-speed wind-tunnel investigation of the aerodynamic characteristics of a full-scale model of the Consolidated Vultee Lark indicates that the missile possesses satisfactory longitudinal-stability and-control characteristics throughout the Mach number range from 0.2 to 0.85, but that the maximum lift coefficients developed are not high enough to insure interception of the target at high altitudes. A reduction in wing loading appears advisable. Although the static longitudinal stability at zero angle of attack changes with Mach number and with lift coefficient, satisfactory control should be possible at all times as the tails retain their relatively large effectiveness throughout the range of Mach numbers and lift coefficients tested. Minimum stability and maximum maneuverability occur around 0.80 Mach number and 0.2 lift coefficient, which corresponds to level flight conditions of the missile. The optimum ratio of tail-to-wing deflection is 0.4.