ALBERT

All Library Books, journals and Electronic Records Telegrafenberg

Your email was sent successfully. Check your inbox.

An error occurred while sending the email. Please try again.

Proceed reservation?

Export
Filter
  • Aerodynamics  (32)
  • Aircraft Stability and Control  (8)
  • 1940-1944  (40)
  • 1943  (16)
  • 1942  (24)
  • 1
    Publication Date: 2018-06-05
    Description: As part of the program of flight tests of airplane propellers to determine compressibility effects at high speeds, preliminary flights have been made with a conventional three-blade propeller (Hamilton Standard 3155-6) on a Bell YP-39 airplane. This preliminary report presents the high-speed data obtained thus far with a brief analysis of the results.
    Keywords: Aerodynamics
    Format: application/pdf
    Location Call Number Expected Availability
    BibTip Others were also interested in ...
  • 2
    Publication Date: 2018-06-05
    Description: Although antispin tail parachutes have been used successfully in spin demonstrations for some time, very little published information is available concerning the size of parachute, the bridle-line length, and the type and location of pack to use for particular airplane. The present paper is an attempt to supply data relating to these factors. The paper is in two parts. The first part reviews the principles of operation of the antispin parachutes, views the principles of operation of the antispin parachutes, summarized available information on actual installations, and discusses parachute loads and pack locations. The second part of the paper reports on systematic tests in the NACA-15-foot and 20-foot free-spinning tunnels at the Langley memorial Aeronautical Laboratory to determine the minimum size and the optimum bridle-line lengths for antispin tail parachutes for current military airplanes. It is concluded that airplanes weighing between 7500 and 14,000 pounds require parachutes 8 feet in diameter and bridle-line lengths between 20 and 50 feet. A positive-ejection mechanism is desirable to throw the parachute clear of the tail and to assure rapid opening. The pack and attachment point must be so located that the equipment will not foul the tail surfaces.
    Keywords: Aircraft Stability and Control
    Format: application/pdf
    Location Call Number Expected Availability
    BibTip Others were also interested in ...
  • 3
    Publication Date: 2018-06-05
    Description: Tests of several modern airplanes indicate that control surfaces with a high degree of aerodynamic balance are likely to possess characteristics which make them unsatisfactory or dangerous in high-speed flight. Dive tests made in the spring of 1940 at the NACA on a naval fighter-type airplane illustrate one form of instability that may be encountered. During a dive at an indicated airspeed of 365 miles per hour, the ailerons suddenly overbalanced. The efforts of the pilot to bring the ailerons back to neutral resulted in a violent oscillation of the control stick from side to side. Fortunately, the force required to return the ailerons to neutral was within the pilot's capabilities. A time history of the maneuver is given in figure1 and typical frames from motion pictures of the cockpit and of the wing, taken during the maneuver, are given in figure 2. In the illustrated case, the occurrence of aerodynamic overbalance was attributed to a slight bulge, approximately 1/16 inch thick, on the lower surface of the leading edges of the ailerons, caused by the installation of additional mass balance ahead of the hinge line. A drawing showing the shape of the bulge is given in figure 3. After this slight protuberance had been eliminated, dives were successfully made at higher speeds.
    Keywords: Aircraft Stability and Control
    Format: application/pdf
    Location Call Number Expected Availability
    BibTip Others were also interested in ...
  • 4
    Publication Date: 2019-06-28
    Description: Test of a ducted body with Internal flow were made in the 8-foot high-speed wind tunnel for the purpose of studying the effects on external drag and an critical speed of the addition of efficient inlet and outlet openings to a basic streamline shape. Drag tests of a 13.6- inch-diameter streamline body of fineness ratio 6.14 were made at Mach numbers ranging from 0.20 to 0.75. The model was centrally mounted on a 9-percent-thick airfoil and was designed to have an efficient airfoil-body juncture and a high critical speed. An air inlet at the nose and various outlets at the tail were added: drag and internal-flow data were obtained over the given speed range. The critical speed of the ducted bodies was found to be as high as that of the streamline body. The external - drag with air flow through the body did not exceed the drag of the basic streamline shape. No appreciable variation in the efficiency of the diffuser section of the internal duct occurred throughout the Mach number range of the tests.
    Keywords: Aerodynamics
    Type: NACA-WR-L-486
    Format: application/pdf
    Location Call Number Expected Availability
    BibTip Others were also interested in ...
  • 5
    Publication Date: 2019-06-28
    Description: Data taken from tests at constant speed to establish trim limits of stability, tests at accelerated speeds to determine stable limits of center of gravity shift, and tests at decelerated speeds to obtain landing characteristics of several model hull forms were used to establish hull design effect on longitudinal stability of porpoising. Results show a reduction of dead rise angle as being the only investigated factor reducing low trim limit. Various methods of reducing afterbody interference increased upper trim limit
    Keywords: Aerodynamics
    Type: NACA-WR-L-468
    Format: application/pdf
    Location Call Number Expected Availability
    BibTip Others were also interested in ...
  • 6
    Publication Date: 2019-06-28
    Description: In order to determine the critical stresses caused by an outward acting pressure on the upper surface of a wing due to the difference in internal and external pressures, torsional tests were made on two curved-sheet specimens subjected to an outward acting normal pressure. Results show that an outward acting normal pressure appreciable raises the critical shear stress for an unstiffened curved sheet; the absolute increase in critical shear stress is slightly greater for a 30 in. rib spacing than for a 10 in. rib spacing.
    Keywords: Aerodynamics
    Type: NACA-WR-L-416
    Format: application/pdf
    Location Call Number Expected Availability
    BibTip Others were also interested in ...
  • 7
    Publication Date: 2019-06-28
    Description: Two airfoil plans were used for propeller blades. One is modified Clark Y section designed for structural reliability and the second an NACA 16 airfoil section designed to produce minimum aerodynamic losses. At low air speeds, the propeller designed for aerodynamic effects showed a gain of from 1.5 to 4.0 percent in propulsive efficiency over the conventional type depending on the pitch. Because of the numerous variables involved, the effect of each one on the aerodynamic characteristics of the propellers could not be isolated.
    Keywords: Aerodynamics
    Type: NACA-WR-L-404
    Format: application/pdf
    Location Call Number Expected Availability
    BibTip Others were also interested in ...
  • 8
    Publication Date: 2019-06-28
    Description: Porpoising characteristics were observed on V-body fitted with tail surfaces for different combinations of load, speed, moment of inertia, location of pivot, elevator setting, and tail area. A critical trim was found which was unaltered by elevator setting or tail area. Critical trim was lowered by moving pivot either forward or down or increasing radius or gyration. Increase in mass and moment of inertia increased amplitude of oscillations. Complete results are tabulated and shown graphically.
    Keywords: Aerodynamics
    Type: NACA-WR-L-479
    Format: application/pdf
    Location Call Number Expected Availability
    BibTip Others were also interested in ...
  • 9
    Publication Date: 2019-06-28
    Description: No abstract available
    Keywords: Aerodynamics
    Type: NACA-WR-L-702
    Format: application/pdf
    Location Call Number Expected Availability
    BibTip Others were also interested in ...
  • 10
    Publication Date: 2019-06-28
    Description: Tests were made in 8-ft high-speed wind tunnel to determine the drag reduction possible by eliminating the barrel jacket of a protruding 50-caliber aircraft gun. It was found that the drag of a standard aircraft gun protruding into the air stream at right angles to the flow can be reduced by 23% by discarding the barrel jacket. At 300 mph and sea-level conditions, this amounts to a decrease in drag of from 83 to 64 pounds. A rough surface finish on the barrel was found to have no adverse effects on the drag of the barrel, the drag being actually less at high Mach Numbers.
    Keywords: Aerodynamics
    Type: NACA-WR-L-581
    Format: application/pdf
    Location Call Number Expected Availability
    BibTip Others were also interested in ...
  • 11
    Publication Date: 2019-06-28
    Description: Tests were conducted on hydrofoil assemblies approximating an arrangement for use under seaplanes or surface boats. A series of hydrofoils, each supported by two struts, was towed at various depths ranging from partial submersions to a depth of 5-chord lengths. At depths greater than 4 or 5 chords, the influence of the surface of the water is small; hydrofoils operating at low speed will have characteristics similar to those of airfoils of the same section.
    Keywords: Aerodynamics
    Type: NACA-WR-L-758
    Format: application/pdf
    Location Call Number Expected Availability
    BibTip Others were also interested in ...
  • 12
    Publication Date: 2019-06-28
    Description: Several tail modifications of the Brewster XSBA-1 scout-bomber were investigated and results compared. Modifications consisted of variation of the chord of the elevator and rudder while the total area of the surfaces is kept constant and variations of the total area of the vertical tail surface. Configuration number 2 reduced trim changes by 50 percent and reduced average elevator control force gradient from 30 to 27 pounds/g. Stick travel required to stall in maneuver was 4.6 inches.
    Keywords: Aerodynamics
    Type: NACA-WR-L-598
    Format: application/pdf
    Location Call Number Expected Availability
    BibTip Others were also interested in ...
  • 13
    facet.materialart.
    Unknown
    In:  CASI
    Publication Date: 2019-06-28
    Description: Analysis was made to determine characteristics required of a balancing-tab system for ailerons in order to reduce aileron stick forces to any desired magnitude. Series of calculations based on section data were made to determine balancing-tab systems of various chord tabs and ailerons that will give, for a particular airplane, zero rate of aileron hinge moment with aileron deflection and yet will produce same maximum rate of roll as a plain unbalanced 15-percent chord aileron of same span. Effects of rolling velocity and of forces in tab link on aileron hinge moments have been included.
    Keywords: Aerodynamics
    Type: NACA-WR-L-346
    Format: application/pdf
    Location Call Number Expected Availability
    BibTip Others were also interested in ...
  • 14
    Publication Date: 2019-06-28
    Description: The effect of various vertical tail arrangements upon the stability and control characteristics of an XP-62 fighter model was investigated. Rudder-free yaw characteristics with take-off power and flaps deflected were satisfactory after dorsal fin modifications. Directional stability was obtained with all modified vertical tails. Satisfactory rudder effectiveness resulted partly because the dual-rotation propellers produced no asymmetric yawing moments. Pedal forces in sideslips were undesirably large but may be easily reduced.
    Keywords: Aircraft Stability and Control
    Type: NACA-WR-L-779
    Format: application/pdf
    Location Call Number Expected Availability
    BibTip Others were also interested in ...
  • 15
    Publication Date: 2019-06-28
    Description: Investigations were undertaken to improve the ailerons of a P-51 fighter so as to obtain greater effectiveness without increasing the stick forces. Modifications consisted of increasing the deflection range of the aileron to 70 percent and changing the original concave section to a thick section with beveled trailing edge. Results of the modified ailerons showed an increase in effectiveness over the original aileron of 70 percent at low speed and 55 percent at high speeds.
    Keywords: Aerodynamics
    Type: NACA-WR-L-636
    Format: application/pdf
    Location Call Number Expected Availability
    BibTip Others were also interested in ...
  • 16
    Publication Date: 2019-06-28
    Description: Hinge-moment, lift, and pressure-distribution measurements were made in the two-dimensional test section of the NACA stability tunnel on a blunt-nose balance-type aileron on an NACA 66,2-216 airfoil at speeds up to 360 miles per hour corresponding to a Mach number of 0.475. The tests were made primarily to determine the effect of speed on the action of this type of aileron. The balance-nose radii of the aileron were varied from 0 to 0.02 of the airfoil chord and the gap width was varied from 0.0005 to 0.0107 of the airfoil chord. Tests were also made with the gap sealed.
    Keywords: Aerodynamics
    Type: NACA-WR-L-431 , NACA-ACR-3F11
    Format: application/pdf
    Location Call Number Expected Availability
    BibTip Others were also interested in ...
  • 17
    Publication Date: 2019-06-28
    Description: Aerodynamics data are obtained for the design of linked balancing tabs and effect of varied tab span and location to produce suitable lateral control characteristics with reasonable stick pressures for high-speed aircraft. Simple and spring-linked balancing tabs may considerably reduce control pressures if aileron system is designed for low maximum aileron deflection. Spring-linked tabs also decrease variation of stick pressure with speed and impart better controlllability at low speeds.
    Keywords: Aerodynamics
    Type: NACA-WR-L-470
    Format: application/pdf
    Location Call Number Expected Availability
    BibTip Others were also interested in ...
  • 18
    Publication Date: 2019-06-28
    Description: Tests were made of an 0.309-chord double-slotted flap on an NACA 65, 3-118, a equals 1.0 airfoil section to determine drag, lift, and pitching-moment characteristics for a range of flap deflections. Results indicate that combination of a low-drag airfoil and a double-slotted flap, of which the two parts moved as a single unit, gave higher maximum lift coefficients than have been obtained with plain, split, or slotted flaps on low-drag airfoils. Pitching moments were comparable to those obtained with other high-lift devices on conventional airfoils for similar lift coefficients.
    Keywords: Aerodynamics
    Type: NACA-WR-L-697 , NACA-ACR-3I20
    Format: application/pdf
    Location Call Number Expected Availability
    BibTip Others were also interested in ...
  • 19
    Publication Date: 2019-06-28
    Description: A pursuit type airplane encountered severe diving moments in high-speed dives which make recovery difficult. For the purpose of investigating these diving moments and finding means for their reduction, a 1/6-scale model of the airplane was tested in the 16-foot high-speed wind tunnel at Ames Aeronautical Laboratory. The test results indicate that up to a Mach number of at least 0.75, the limit of the tests, the dive-recovery difficulties can be alleviated and the longitudinal maneuverability improved by the substitution of a long symmetrical fuselage for the standard fuselage.
    Keywords: Aircraft Stability and Control
    Type: NACA-WR-A-65
    Format: application/pdf
    Location Call Number Expected Availability
    BibTip Others were also interested in ...
  • 20
    Publication Date: 2018-06-05
    Description: Tests were made in the NACA two-dimensional low-turbulence tunnel of three gun ports with a height of approximately 4 percent of the chord faired into an NACA 66,2-213 low-drag-airfoil section by bulging the section at the gun port. Gun ports faired in this manner had practically no effect on the maximum lift and the critical compressibility speed of the section and showed only small increase in the drag in the range of lift coefficients for high-speed and cruising-flight conditions.
    Keywords: Aerodynamics
    Format: application/pdf
    Location Call Number Expected Availability
    BibTip Others were also interested in ...
  • 21
    Publication Date: 2019-06-28
    Description: Characteristics are determined for various modifications of 0.155-chord blunt-nose aileron on semispan model of tapered fighter plane wing. Ailerons with 40 percent nose balance reduced high-speed stick forces. Increased balance chord increases effectiveness and reduces high-speed stick forces. Increased balance chord increases effectiveness and reduces adverse effects of gap at aileron hose. Increase of nose radii increased negative slope of curve hinge-movement coefficient plotted against deflection. Extended deflection range decreased aileron effectiveness for small deflections but increased it at large deflections. Peak pressures at noses of ailerons are relatively high at moderate deflections.
    Keywords: Aerodynamics
    Type: NACA-WR-L-262
    Format: application/pdf
    Location Call Number Expected Availability
    BibTip Others were also interested in ...
  • 22
    Publication Date: 2019-06-28
    Description: Several airfoils, Including a conventional NACA 23021 and some low-drag airfoils for which the thickness had been increased to the point that they were considered doubtfully conservative with respect to separation, were investigated as smooth airfoils and after the application of a standard roughness. The results show some of the airfoils to be critical to separation resulting from such flow disturbances. It is concluded, pending the further investigation of separation difficulties, that airfoil sections falling definitely within the conservative range should be used.
    Keywords: Aerodynamics
    Type: NACA-WR-L-659
    Format: application/pdf
    Location Call Number Expected Availability
    BibTip Others were also interested in ...
  • 23
    Publication Date: 2019-06-28
    Description: The effects of mass distribution on lateral stability and control characteristics of an airplane have been determined by flight tests of a model in the NACA free-flight tunnel. In the investigation, the rolling and yawing movements of inertia were increased from normal values to values up to five times normal. For each moment-of-inertia condition, combinations of dihedral and vertical-tail area representing a variety of airplane configurations were tested. The results of the flight tests of the model were correlated with calculated stability and control characteristics and, in general, good agreement was obtained. The tests showed the following effects of increased rolling and yawing moments of inertia: no appreciable change in spiral stability; reductions in oscillatory stability that were serious at high values of dihedral; a reduction in the sensitivity of the model to gust disturbances; and a reduction in rolling acceleration provided by the ailerons, which caused a marked increase in time to reach a given angle of bank. The general flight behavior of the model became worse with increasing moments of inertia but, with combinations of small effective dihedral and large vertical-tail area, satisfactory flight characteristics were obtained at all moment-of-inertia conditions.
    Keywords: Aerodynamics
    Type: NACA-WR-L-388 , NACA-ARR-3H31
    Format: application/pdf
    Location Call Number Expected Availability
    BibTip Others were also interested in ...
  • 24
    Publication Date: 2019-06-28
    Description: Investigations of strengths of hot wires at high velocities were conducted with platinum, nickel, and tungsten at approximately 200 Degrees Celcius hot-wire temperature. The results appear to disqualify platinum for velocities approaching the sonic range; whereas nickel withstands sound velocity, and tungsten may be used for supersonic velocities under standard atmospheric conditions. Hot wires must be supported by rigid prolongs at high velocities to avoid wire breakage. Resting current measurements for constant temperature show agreement with King's relation.
    Keywords: Aerodynamics
    Type: NACA-TN-880
    Format: application/pdf
    Location Call Number Expected Availability
    BibTip Others were also interested in ...
  • 25
    Publication Date: 2019-08-17
    Description: This report deals with the development of a method which gives a lucid and convenient solution of the flow conditions in the vicinity of a common, thick airfoil section wherein the thickness of the profile is taken into account. The method consists in making the airfoil the streamline in a parallel flow by disposing on its mean line certain source and vortex distributions the fields of which are superposed on the parallel flow. These distributions of singularities are secured for the generalized Karman-Trefftz profile by means of conformal transformation from the flow about a circle. Five different distribution functions are afforded for the density of superposition, which combine in a specified manner to the necessary distributions of singularity and represent a generalized Karman-Trefftz profile in parallel flow. For these profiles the speed for each of the five distributions is then computed independently of the angle of attack.
    Keywords: Aerodynamics
    Type: NACA-TM-1023
    Format: application/pdf
    Location Call Number Expected Availability
    BibTip Others were also interested in ...
  • 26
    Publication Date: 2019-08-14
    Description: Wing pressure distribution diagrams for several angles of attack and flap deflections of 0 degrees, 20 degrees, and 40 degrees are presented. The normal force coefficients agree with lift coefficients obtained in previous test of the same model, except for the maximum lifts with flap deflection. Pressure distribution measurements were made at Reynolds Number of about 6,000,000.
    Keywords: Aerodynamics
    Type: NACA-WR-L-678
    Format: application/pdf
    Location Call Number Expected Availability
    BibTip Others were also interested in ...
  • 27
    Publication Date: 2019-08-07
    Description: At the request of the Army Air Forces, Materiel Command, tests were made in the two-Dimensional low-turbulence tunnel of a mode l submitted by Bell Aircraft Corporation as the tip section of the wing of the xp-63 airplane. " The model was a NACA 66, 2x-2l6 a = 0.6 airfoil section of 50-inch chord and made of dural according to standard sheet-metal practice. The model was fitted for an internal-balance aileron with a tab and a Frise type aileron. Several alterations of the skirts and balance on the internal- balance aileron were tested to obtain the various aerodynamic characteristics of the aileron.
    Keywords: Aerodynamics
    Format: application/pdf
    Location Call Number Expected Availability
    BibTip Others were also interested in ...
  • 28
    facet.materialart.
    Unknown
    In:  CASI
    Publication Date: 2019-07-13
    Description: The present report deals with a number of problems, particularly with the interaction of the fuselage with the wing and tail, on the basis of simple calculating method's derived from greatly idealized concepts. For the fuselage alone it affords, in variance with potential theory, a certain frictional lift in yawed flow, which, similar to the lift of a wing of small aspect ratio, is no longer linearly related to the angle of attack. Nevertheless there exists for this frictional lift something like a neutral stability point the position of which on oblong fuselages appears to be associated with the lift increase of the fuselage in proximity to the zero lift, according to the present experiments. The Pitching moments of the fuselage can be determined with comparatively great reliability so far as the flow conditions in the neighborhood of the axis of the fuselage can be approximated if the fuselage were absent, which, in general, is not very difficult. For the unstable contribution of the fuselage to the static longitudinal stability of the airplane it affords comparatively simple formulas, the evaluation of which offers little difficulty. On the engine nacelles there is, in addition a very substantial wing moment contribution induced by the nonuniform distribution of the transverse displacement flow of the nacelle along the wing chord; this also can be represented by a simple formula. A check on a large number of dissimilar aircraft types regarding the unstable fuselage and nacelle moments disclosed an agreement with the wind-tunnel tests, which should be sufficient for practical requirements. The errors remained throughout within the scope of instrumental accuracy.
    Keywords: Aerodynamics
    Type: NACA-TM-1036 , Luftfahrtforschung; 18; 3-Feb; 52-56
    Format: application/pdf
    Location Call Number Expected Availability
    BibTip Others were also interested in ...
  • 29
    Publication Date: 2019-07-12
    Description: Preliminary data are presented on the variation of the maximum lift coefficient with Mach number. The data were obtained from tests in the 8-foot high-speed tunnel of three NACA 16-series airfoils of 1-foot chord. Measurements consisted primarily of pressure-distribution measurements in order to illustrate the nature of the phenomena. It was found that the maximum lift coefficient of airfoils is markedly affected by compressibility even at Mach numbers as low as 0.2. At high Mach numbers pronounced decrease of the maximum lift coefficient was found. The magnitude of the effects of compressibility on the maximum lift coefficient and the low speeds at which these effects first appear indicate clearly that consideration of the take-off thrust for propellers will give results seriously in error if these considerations are based on the usual low-speed maximum-lift-coefficient data generally used.
    Keywords: Aerodynamics
    Type: NACA-ACR-246 , NACA-SR-246
    Format: application/pdf
    Location Call Number Expected Availability
    BibTip Others were also interested in ...
  • 30
    Publication Date: 2019-07-12
    Description: An investigation has been made to determine the motions of and the flight paths describe by a Navy dive-bombing airplane in simulated diving attacks. The data necessary to evaluate these items, with the exception of the atmospheric wind data, were obtained from automatic recording instruments installed entirely within the airplane. The atmospheric wind data were obtained from the ground by the balloon-theodolite method. The results of typical dives at various dive angles are presented in the form of time histories of the motion of the airplane as well as flight paths calculated with respect to still air and with respect to the ground.
    Keywords: Aircraft Stability and Control
    Type: NACA-ACR-248 , NACA-SR-248
    Format: application/pdf
    Location Call Number Expected Availability
    BibTip Others were also interested in ...
  • 31
    Publication Date: 2019-07-12
    Description: This report covers tests of a 5-foot model of the NACA 66,2-420 low-drag airfoil at high speeds including the critical compressibility speed. Section coefficients of lift, drag, and pitching moment, and extensive pressure-distribution data are presented. The section drag coefficient at the design lift coefficient of 0.4 increased from 0.0042 at low speeds to 0.0052 at a Mach number of 0.56 (390 mph at 25,000 ft altitude). The critical Mach number was about 0.60. The results cover a Reynold number range from 4 millions to 17 millions.
    Keywords: Aerodynamics
    Type: NACA-ACR-234 , NACA-SR-234
    Format: application/pdf
    Location Call Number Expected Availability
    BibTip Others were also interested in ...
  • 32
    Publication Date: 2019-07-12
    Description: Results of a study to determine the effects on turning performance due to various assumed modifications to a typical Naval fighter airplane are presented. The modifications considered included flaps of various types, both part and full space, increased supercharging, and increased wing loading. The calculations indicated that near the low-speed end of the speed range, the turning performance, as defined by steady level turns at a given speed, would be improved to some extent by any of the flaps considered at altitudes up to about 25,000 feet. (If turning is not restricted to the conditions of no loss of speed or altitude, more rapid turning can, of course, be accomplished with the aid of flaps, regardless of altitude.) Fowler flaps and NACA slotted flaps appeared somewhat superior to split or perforated split flaps for maneuvering purposes, particularly if the flap position is not adjustable. Similarly, better turning performance should be realized with full-span than with part-span flaps. Turning performance over the lower half of the speed range would probably not be materially improved at any altitude by increased supercharging of the engine unless the propeller were redesigned to absorb the added power more effectively; with a suitable propeller the turning performance at high altitudes could probably be greatly improved with increased supercharging. A reduction in wing area with the aspect ratio held constant would result in impairment of turning performance over practically the entire speed range at all altitudes.
    Keywords: Aircraft Stability and Control
    Type: NACA-ACR-222 , NACA-SR-222
    Format: application/pdf
    Location Call Number Expected Availability
    BibTip Others were also interested in ...
  • 33
    Publication Date: 2019-07-12
    Description: The effects of direction of propeller rotation on factors affecting the longitudinal stability of the XB-28 airplane were measured on a 1/10-scale model in the 7- by 10-foot tunnel of the Ames Aeronautical Laboratory. The main effect observed was that caused by regions of high downwash behind the nacelles (power off as well as power on with flaps neutral). The optimum direction of propeller rotation, both propellers rotating up toward the fuselage, shifted this region off the horizontal tail and thus removed its destabilizing effect. Rotating both propellers downward toward the fuselage moved it inboard on the tail and accentuated the effect, while rotating both propellers right hand had an intermediate result. Comparisons are made of the tail effects as measured by force tests with those predicted from the point-by-point downwash and velocity surveys in the region of the tail. These surveys in turn are compared with the results predicted from available theory.
    Keywords: Aircraft Stability and Control
    Type: NACA-ACR-224 , NACA-SR-224
    Format: application/pdf
    Location Call Number Expected Availability
    BibTip Others were also interested in ...
  • 34
    Publication Date: 2019-07-12
    Description: Tests were made in the NACA 19-foot pressure tunnel of a simplified twin-engine bomber model with an NACA low-drag wing primarily to obtain an indication of the effects of engine nacelles on the characteristics of the model both with and without simple split trailing-edge flaps. Nacelles with conventional-type cowlings representative of those used on an existing high-performance airplane and with NACA high-speed type E cowlings were tested. The tests were made without propeller slipstream. The aerodynamic effects of adding the nacelles to the low-drag wing were similar to the effects commonly obtained by adding similar nacelles to conventional wings. The maximum lift coefficient without flaps was slightly increased, but the increment in maximum lift due to deflecting the flaps was somewhat decreased. The stalling characteristics were improved by the presence of the nacelles. Addition of the nacelles had a destabilizing effect on the pitching moments, as is usual for nacelles that project forward of the wing. The drag increments due to the nacelles were of the usual order of magnitude, with the increment due to the nacelles with NACA type E cowlings approximately one-third less than that of the nacelles with conventional cowlings with built-in air scoops.
    Keywords: Aerodynamics
    Type: NACA-ACR-225 , NACA-SR-225
    Format: application/pdf
    Location Call Number Expected Availability
    BibTip Others were also interested in ...
  • 35
    Publication Date: 2019-07-12
    Description: An investigation was made in the LWAL 7- by 10-foot tunnel of internally balanced, sealed ailerons for the Curtiss XP-60 airplane. Ailerons with tabs and. with various amounts of balance were tested. Stick forces were estimated for several aileron arrangements including an arrangement recommended for the airplane. Flight tests of the recommended arrangement are discussed briefly in an appendix, The results of the wind-tunnel and flight tests indicate that the ailerons of large or fast airplanes may be satisfactorily balanced by the method developed.
    Keywords: Aerodynamics
    Type: NACA-ACR-257 , NACA-SR-257
    Format: application/pdf
    Location Call Number Expected Availability
    BibTip Others were also interested in ...
  • 36
    Publication Date: 2019-07-12
    Description: As an aid to airplane designers interested in providing pursuit airplanes with decelerating devices intended to increase the firing time when overtaking another airplane, formulas are given relating the pertinent distances and speeds in horizontal flight to the drag increase required. Charts are given for a representative parasite-drag coefficient from which the drag increase, the time gained, and the closing distance may be found. The charts are made up for three values of the ratio of the final speed of the pursuing airplane to the speed of the pursued airplane and for several values of the ratio of the speed of the pursued airplane to the initial speed of the pursuing airplane. Charts are also given indicating the drag increases obtainable with double split flaps and with conventional propellers. The use of the charts is illustrated by an example in which it is indicated that either double split flaps or, under certain ideal conditions, reversible propellers should provide the speed reductions required.
    Keywords: Aerodynamics
    Type: NACA-ACR-220 , NACA-SR-220
    Format: application/pdf
    Location Call Number Expected Availability
    BibTip Others were also interested in ...
  • 37
    Publication Date: 2019-07-12
    Description: Tests were made in the NACA two-dimensional low turbulence pressure tunnel of a highly cambered low-drag airfoil (NACA 65,3-618) with a plain flap designed for lift control. The results indicate that such a combination offers attractive possibilities for obtaining low profile-drag coefficients over a wide range of lift coefficients without large reductions of critical speed.
    Keywords: Aerodynamics
    Type: NACA-ACR-242 , NACA-SR-242
    Format: application/pdf
    Location Call Number Expected Availability
    BibTip Others were also interested in ...
  • 38
    Publication Date: 2019-07-12
    Description: The development of the laminar boundary layer in a compressible fluid is considered. Formulas are given for determining the boundary-layer thickness and the ratio of the boundary-layer Reynolds number to the body Reynolds number for airfoils and bodies of revolution. It i s shown that the effect of compressibility will profoundly alter the Reynolds number corresponding to the upper limit of the range of the low-drag coefficients . The available data indicate that for low-drag and high critical compressibility speed airfoils and bodies of revolution, this effect is favorable.
    Keywords: Aerodynamics
    Type: NACA-ACR-252 , NACA-SR-252
    Format: application/pdf
    Location Call Number Expected Availability
    BibTip Others were also interested in ...
  • 39
    Publication Date: 2019-07-12
    Description: Hinge-moment parameters for several typical ailerons were calculated from section data with the aspect-ratio correction as usually determined from lifting-line theory. The calculations showed that the agreement between experimental and calculated results was unsatisfactory. An additional aspect-ratio correction, calculated by the method of lifting-surface theory, was applied to the slope of the curve of hinge-moment coefficient against angle of attack at small angles of attack. This so-called streamline-curvature correction brought the calculated and experimental results into satisfactory agreement.
    Keywords: Aerodynamics
    Type: AD-A801563 , NACA-WR-L-281 , NACA-CB-3L02
    Format: text
    Location Call Number Expected Availability
    BibTip Others were also interested in ...
  • 40
    Publication Date: 2019-07-12
    Description: The aileron characteristics of a Grumman F4F-3 airplane were determined in flight by means of NACA recording and indicating instruments. The results show that the ailerons met NACA minimum requirements for satisfactory control throughout a limited speed range. A helix angle of approximately 0.07 radian was produced with flaps down at speeds from 90 to 115 miles per hour indicated airspeed and with flaps up from 115 to 200 miles per hour. With flaps up at 90 miles per hour, the helix angle dropped to 0.055 radian; above 200 miles per hour heavy aileron stick forces seriously restricted maneuverability in roll.
    Keywords: Aircraft Stability and Control
    Type: NACA-ACR-239 , NACA-SR-239
    Format: application/pdf
    Location Call Number Expected Availability
    BibTip Others were also interested in ...
Close ⊗
This website uses cookies and the analysis tool Matomo. More information can be found here...