ALBERT

Beschreibung: At the request of the Materiel Division, Wright Field, the National Advisory Committee for Aeronautics is conducting a program of flight tests on a Kellett YG-1B autogiro equipped with a new type of rotor blade. The new blades are tapered in both plan form. and thickness and are designed to avoid periodic blade twist. One phase of the investigation, involving determination of the moments of the resultant rotor force about the trunnions on which the hub is pivoted for control, has been completed. The results obtained are reported herein.

Beschreibung: Wind-tunnel tests were conducted on a model wing-nacelle combination to determine the practicability of cooling radial engines by forcing the cooling air into wing-duct entrances located in the propeller slipstream, passing the air through the engine baffles from rear to front, and ejecting the air through an annular slot near the front of the nacelle. The tests, which were of a preliminary nature, were made on a 5-foot-chord wing and a 20-inch-diameter nacelle. A 3-blade, 4-foot-diameter propeller was used. The tests indicated that this method of cooling and cowling radial engines is entirely practicable providing the wing of the prospective airplane is sufficiently thick to accommodate efficient entrance ducts , The drag of the cowlings tested was definitely less than for the conventional N.A.C.A. cowling, and the pressure available at low air speed corresponding to operation on the ground and at low flying speeds was apparently sufficient for cooling most present-day radial engines.

Beschreibung: Tests of three-blade, adjustable-pitch counterrotating tandem model propellers, adjusted to absorb equal power at maximum efficiency of the combination, were made at Stanford University. The aerodynamic characteristics, for blade-angle settings of 15, 25, 35, 45, 55, and 65 degrees at 0.75R of the forward propeller and for diameters spacings of 8-1/2, 15 and 30% were compared with those of three-blade and six-blade propellers of the same blade form. It was found that, in order to realize the condition of equal power at maximum efficiency, the blade angles for the rear propeller must be generally less than for the forward propeller, the difference increasing the blade angle. The tests showed that, at maximum efficiency, the tandem propellers absorb about double the power of three-blade propellers and about 8% more power than six-blade propellers having the pitch of the forward propeller of the tandem combination. The maximum efficiency of the tandem propellers was found to be from 2-15% greater than for six-blade propellers, the difference varying directly with blade angle. It was also found that the maximum efficiency of the tandem propellers was greater than that of a three-blade propeller for blade angles at 0.75R of 25 degrees or more. The difference in maximum efficiency again varied directly with blade angle, being about 9% for 65 degrees at 0.75R.

Beschreibung: The effects of the geometrical arrangement of tricycle landing gears on various characteristics of an airplane equipped with such landing gear is discussed. The characteristics discussed include directional stability, overturning tendencies, steering and ground handling, shimmy, takeoff, and porpoising. The conclusions are summarized in a table.

Beschreibung: Engine and airplane performance data have been gathered from various sources and analyzed to determine indications of the most economical methods of flight operation from a consideration of fuel expenditure. The analysis includes the influence of such facts as fuel-air ratio, engine speed, engine knock, altitude, cylinder cooling, spark timing, and limits of cruising brake mean effective pressure. The results indicate that the cheapest power is obtained with approximately correct mixture at low engine speed and highest permissible manifold pressure. If more power is desired, the methods of obtaining it are, in order of fuel economy: (a) increasing the engine speed and maintaining safe cylinder temperatures by cooling; (b) retarding the spark or cooling further to permit higher manifold pressure; and, (c) riching the mixture. The analysis further shows that the maximum time endurance of flight occurs at the air speed corresponding to minimum thrust horsepower required and with minimum practicable engine speed. Maximum mileage per pound of fuel is obtained at slightly higher air speed. The fuel-air ratio should be approximately the theoretically correct ratio in both cases. For an engine equipped with a geared supercharger, as in the example presented, and with knock as the limiting condition, a comparison of operation at sea level and at 6,000 feet shoes flight at altitude to be more economical on the basis of both range and endurance.

Beschreibung: An electrical-type meter has been developed for measuring mass rates of flow of gasoline or other nonconducting fluids. Its temperature dependence is small over a large range and it has no known vibrational or viscosity errors. The maximum temperature rise is less than 5 C. The rates of flow, measurable within 1% with the present instrument, are approximately 100 to 1,000 or more pounds of gasoline per hour when a potentiometer is used, or 100 to 300 pounds per hour when a deflection-type meter is used.

Beschreibung: Present designs for large flying boats are characterized by high wing loading, high aspect ratio, and low parasite drag. The high wing loading results in the universal use of flaps for reducing the takeoff and landing speeds. These factors have an effect on takeoff performance and influence to a certain extent the design of the hull. An investigation was made of the influence of various factors and design parameters on the takeoff performance of a hypothetical large flying boat by means of takeoff calculations. The parameters varied in the calculations were size of hull (load coefficient), wing setting, trim, deflection of flap, wing loading, aspect ratio, and parasite drag. The takeoff times and distances were calculated to the stalling speeds and the performance above these speeds was studied separately to determine piloting technique for optimum takeoff. The advantage of quick deflection of the flap at high water speeds is shown.

Beschreibung: The fundamental principles of fluid flow, pressure losses, and heat transfer have been presented and analyzed for the case of a smooth tube with fully developed turbulent flow. These equations apply to tubes with large length-diameter ratios where the f1ow is at a high Reynolds Number. The error introduced by using these equations increases as the magnitude of the tube length and the air-flow Reynolds Number approaches the values encountered in modern radiator designs. Accordingly, heat-transfer tests on radiator sections were made and the results are presented in nondimensional form to facilitate their use and for comparison with other heat-transfer data. In addition, pressure losses were measured along smooth tubes of circular, square, and rectangular cross section and the results were also correlated and are presented in nondimensional form. The problem of a radiator design for a particular installation is solved, the experimental heat-transfer and pressure-loss data being used, on a basis of power chargeable to the radiator for form drag, for propelling the weight, and for forcing the air through the radiator. The case of an installation within a wing or an engine nacelle is considered. An illustration of radiator design is carried through for an arbitrary set of conditions. Sufficient detail is given to enable the reader to reproduce the analysis for any given case.

Beschreibung: The drag of closed-cockpit and transport-type windshields was determined from tests made at speeds from 200 to 440 miles per hour in the NACA 8-foot high-speed wind tunnel. This speed range corresponds to a test Reynolds number range of 2,510,000 to 4,830,000 based on the mean aerodynamic chord of the full-span model (17.29 inches). The shapes of the windshield proper, the hood, and the tail fairing were systematically varied to include common types and a refined design. Transport types varied from a reproduction of a current type to a completely faired windshield. The results show that the drag of windshields of the same frontal area, on airplanes of small to medium size, may account for 15% of the airplane drag or may be reduced to 1%. Optimum values are given for windshield and tail-fairing lengths; the effect, at various radii is shown. The longitudinal profile of a windshield is shown to be most important and the transverse profile, to be much less important. The effects of retaining strips, of steps for telescoping hoods, and of recessed windows are determined. The results show that the drag of transport-type windshields may account for 21% of the fuselage drag or may be reduced to 2%.

Beschreibung: When an airplane is operating at high altitude, it is necessary to use a supercharger to maintain ground pressure at the carburetor inlet. This maintenance and high intake-manifold pressure tends to keep the power output of the engine at ground-level value. The air, being compressed by the supercharger, however, is heated by adiabatic compression and friction to a temperature that seriously affect the performance of the engine. It is thus necessary to use an intercooler to reduce the temperature of the air between the supercharger outlet and the carburetor inlet. The amount of cooling required of the intercooler depend on the efficiency of the supercharger installation. In this investigation, several types of intercoolers were compared and a design procedure that will give the best intercooler for a given set of conditions is indicated. The figure of merit used for the selection of the best design was the total power consumed by the intercooler. This value includes the power required to transport the weight of the intercooler as well as the power used to force the charge air and the cooling air through the intercooler. The cost, size and practicality of construction were not considered, inasmuch as it was thought that a survey of possibilities of improvement in design would be of interest, regardless of whether the improvement could be immediately realized. Three types of intercoolers are included in this survey: a counterflow intercooler with indirect cooling surface in the form of fins, a counterflow intercooler with direct cooling surfaces, and a cross-flow, tube-type intercooler.

Beschreibung: An investigation was undertaken to determine the character and importance of the transition phase between the ground run and steady climb in the takeoff of an airplane and the effects of various factors on this phase and on the airborne part of the takeoff as a whole. The information was obtained from a series of step-by-step integrations, which defined the motion of the airplane during the transition and which were based on data derived from actual takeoff tests of a Verville AT airplane. Both normal and zoom takeoffs under several loading and takeoff speed conditions were considered. The effects of a moderate wind with a corresponding wind gradient and the effect of proximity of the ground were also investigated. The results show that, for normal takeoffs, the best transition was realized at the lowest possible takeoff speed. Moreover, this speed gave the shortest overall takeoff distance for normal takeoffs. Zoom takeoffs required a shorter overall takeoff run than normal takeoffs, particularly with a heavy landing, if the obstacle to be cleared was sufficiently high (greater than 50 feet); no advantage was indicated to the airplane with a light loading if the height to be cleared was less. The error resulting from the neglect of the transition in the calculation of the airborne distance of takeoff was found to vary from 4% with the heaviest loading considered to -4% with the lightest loading for normal takeoffs over a 100-ft obstacle; the percentage error was twice as great for a 50-foot obstacle. For zoom takeoffs the error attained much greater values. The average wind gradient corresponding to a 5-mile-per-hour surface wind reduced the airborne distance required to clear a 50-foot obstacle by about 9% with the lightest loading and 16% with the heaviest loading; for both cases. The overall reduction due to this wind was approximately twice that resulting from the wind gradient alone. A simple expression for the reduction of observed takeoff performance to no-wind conditions is presented. Ground effect is shown to reduce the airborne distance to attain a height of 50 foot by 10% with the lightest loading and 16% with the heaviest loading; for a 100-foot obstacle the percentage reduction was about 1/2 as great.

Beschreibung: An investigation is in progress in the NACA full-scale wind tunnel to determine the drag and propulsive efficiency of nacelle sizes. In contrast with the usual tests with a single nacelle, these tests were conducted with nacelle-propeller installations on a large model of a 4-engine airplane. Data are presented on the first part of the investigation, covering seven nacelle arrangements with nacelle diameters from 0.53 to 1.5 times the wing thickness. These ratios are similar to those occurring on airplane weighing from about 20 to 100 tons. The results show that the drag, the propulsive efficiency, and the overall efficiency of the various nacelle arrangements as functions of the nacelle size, the propeller position, and the airplane lift coefficient. The effect of the nacelles on the aerodynamic characteristics of the model are shown for both propeller-removed and propeller-operating conditions.

Beschreibung: In the design of a cowling a certain pressure drop across the cylinders of a radial air-cooled engine is made available. Baffles are designed to make use of this available pressure drop for cooling. The problem of cooling an air-cooled engine cylinder has been treated, for the most part, from considerations of a large heat-transfer coefficient. The knowledge of the precise cylinder characteristics that give a maximum heat-transfer coefficient should be the first consideration. The next problem is to distribute this ability to cool so that the cylinder cools uniformly. This report takes up the problem of the design of a baffle for a model cylinder. A study has been made of the important principles involved in the operation of a baffle for an engine cylinder and shows that the cooling can be improved 20% by using a correctly designed baffle. Such a gain is as effective in cooling the cylinder with the improved baffle as a 65% increase in pressure drop across the standard baffle and fin tips.

Beschreibung: In many installations of castering rubber-tired wheels there is a tendency for the wheel to oscillate violently about the spindle axis. This phenomenon, popularly called 'shimmy,' has occurred in some airplane tail wheels and has been corrected in two ways: first by the application of friction in the spindles of the tail wheels; and, second, by locking the wheels while taxiing at high speeds. Shimmy is common with the large wheels used as nose wheels in tricycle landing gears and, since it is impossible to lock the wheels, friction in the nose-wheel spindle has been the sole means of correction. Because the nose wheel is larger than the conventional tail wheel and usually carries a greater load, the larger amounts of spindle friction necessary to prevent shimmy are objectionable. the present paper presents a theoretical and experimental study of the problem of the stability of castering wheels for airplane landing gears. On the basis of simplified assumptions induced from experimental observations, a theoretical study has been made of the shimmy of castering wheels. The theory is based on the discovery of a phenomenon called 'kinematic shimmy' and is compared quantitatively with the results of model experiments. Experimental checks, using a model having low-pressure tires, are reported and the applicability of the results to full scale is discussed. Theoretical methods of estimating the spindle viscous damping and spindle solid friction necessary to avoid shimmy - lateral freedom - is introduced.

Beschreibung: Tests of 2-blade, adjustable-pitch, counterrotating tandem model propellers, adjusted to absorb equal power at maximum efficiency, were made at Stanford University. The characteristics, for 15 degrees, 25 degrees, 35 degrees, and 45 degrees pitch settings at 0.75 R of the forward propeller and for 8 1/2%, 15% and 30% diameter spacings, were compared with those of 2-blade and 4-blade propellers of the same blade form. The tests showed that the efficiency of the tandem propellers was from 0.5% to 4% greater than that of a 4-blade propeller and, at the high pitch settings, not appreciable inferior to that of a 2-blade propeller. It was found that the rear tandem propeller should be set at a pitch angle slightly less than that of the forward propeller to realize the condition of equal power at maximum efficiency. Under this condition the total power absorbed by the tandem propellers was from 3% to 9% more than that absorbed by the 4-blade propeller and about twice that absorbed by a 2-blade propeller.

Beschreibung: The pressure distribution on the fuselage of a midwing airplane model was measured in the NACA 8-foot high speed wind tunnel at speeds from 140 to 440 miles per hour for lift coefficients ranging from -0.2 to 1.0. The primary purpose of the tests was to provide data showing the air pressures on various parts of the fuselage for use in structural design. The data may also be used for the design of scoops and vents. The results show that the highest negative pressures occurred near the wing and were more dependent on the wing than on the fuselage. At high speeds, the magnitude of the pressure coefficients as predicted from pressure coefficients determined experimentally at low speeds by application of the theoretical factor 1/(square root)1-M(exp 2) (where M is the ratio of the air speed to the speed of sound in air) may misrepresent the actual conditions. At the points where the maximum negative pressures ocurred, however, the variation of the pressure coefficients was in good agreement with the theoretical factor, indicating that this factor may afford satisfactory predictions of critical speed, at least for fuselages similar to the shape tested.