ALBERT

Notes: Abstract Specimen thickness is the main experimental factor controlling the results of illite crystallinity (IC) or crystallite size measurements on sedimentation slides. Different values obtained from thick and thin preparations are due to grain-size gradation effects, which may exclude larger and higher ordered grains from contributing to the diffraction. Orientation effects control the measured peak intensity. The change from poor particle orientation in thick slides to high orientation in very thin slides is marked by an increase in specimen density, diminishing non-basal reflections, and by a strong increase in peak intensity. A plateau with constant peak breadths is observed if thin slides of well ordered, platy illites are used. A similar plateau can be recognized for thick preparations of specimens from less ordered materials, but not from well ordered ones. Therefore, it is suggested that IC is determined on very thin sedimentation slides with a thickness of 0.25 mg/cm2 or less. Ultrasonic and H2O2 treatments enhance the degree of particle orientation by destruction of grain aggregates and organic compounds, leading to smaller peak breadths and higher intensities.

Notes: Abstract Five basalt samples from the Point Sal ophiolite, California, were examined using HRTEM and AEM in order to compare observations with interpretations of XRD patterns and microprobe analyses. XRD data from ethylene-glycol-saturated samples indicate the following percentages of chlorite in mixed-layer chlorite–smectite identified for each specimen: (i) L2036 ± 50%, (ii) L2035 ± 70 and 20%, (iii) 1A-13 ± 70%, (iv) 1B-42 ± 70%, and (v) 1B-55 = 100%. Detailed electron microprobe analyses show that ‘chlorite’analyses with high Si, K, Na and Ca contents are the result of interlayering with smectite-like layers. The Fe/(Fe + Mg) ratios of mixed-layer phyllosilicates from Point Sal samples are influenced by the bulk rock composition, not by the percentage of chlorite nor the structure of the phyllosilicate.Measurements of lattice-fringe images indicate that both smectite and chlorite layers are present in the Point Sal samples in abundances similar to those predicted with XRD techniques and that regular alternation of chlorite and smectite occurs at the unit-cell scale. Both 10- and 14-Å layers were recorded with HRTEM and interpreted to be smectite and chlorite, respectively. Regular alternation of chlorite and smectite (24-Å periodicity) occurs in upper lava samples L2036 and 1A-13, and lower lava sample 1B-42 for as many as seven alternations per crystallite with local layer mistakes. Sample L2035 shows disordered alternation of chlorite and smectite, with juxtaposition of smectite-like layers, suggesting that randomly interlayered chlorite (〈0.5)–smectite exists. Images of lower lava sample 1B-55 show predominantly 14-Å layers. Units of 24 Å tend to cluster in what may otherwise appear to be disordered mixtures, suggesting the existence of a corrensite end-member having thermodynamic significance.

Notes: Abstract White mica crystallinity studies have been carried out on 90 samples of mudrocks, six of spotted slate, and five of accretionary lapilli tuff from the area around the Berwyn Hills, North Wales. Strain was measured for some of the spotted slate and tuff samples. The metamorphic grade increases from southeast to northwest, with values of the Kübler index varying from 0.64 to 0.20Δ2θ. Metamorphic zonal boundaries follow the strike of bedding and cleavage, but crystallinity values increase into stratigraphically younger rocks on the northwest side of the Berwyn Dome. This effect is attributed mainly to a rapid increase in the thickness of synmetamorphic overburden to the northwest, comprising exposed Silurian turbidites and inferred Lower Devonian non-marine sediments. Strain variations have a more local influence on crystallinity, and lateral variations in the contemporary geothermal gradient cannot be ruled out. However, only with unrealistically high gradients would the need for a thick Lower Devonian component to the overburden be removed. This reasoning implies that the metamorphic peak was coeval with the Acadian (late Caledonian) event, rather than with an early diastathermal event.

Notes: Abstract Illite crystallinity (IC) measurements, determination of the proportion of 2M mica-polytypes and organic-matter reflectance measurements establish regional diagenetic/low-grade metamorphic trends for the Taconian and Acadian belts of Gaspé Peninsula.IC varies as a function of many factors besides maximum burial temperature and heating time. Correlation between IC and %2M illite polytypes for the Fortin Group and Temiscouata Formation suggests (i) that the amount of high-grade detrital mica in the samples is low, and (ii) that IC can be used with some confidence as an estimator of regional thermal maturation levels. Correlation of these parameters with available organic reflectance values further supports this assumption. The illites of the Temiscouata and western Fortin groups are mostly phengitic in composition, whereas in the eastern outcrop belt they are more Mg- and Fe-rich (celadonitic), but generally also of lower grade and lower 2M content. The d(060) values for illites measured on the unorientated 〈2-μm fraction of samples fall between 1.502 and 1.503 Å (range: 1.500–1.504 Å), indicating relatively low octahedral occupancy by Mg and Fe (between one-fifth and one-third of the available spaces). Pyrophyllite and paragonite were not detected. Chlorites are Fe-rich and ripidolitic.The IC map for the Acadian belt of the peninsula displays general congruence between IC contours (2200 sample points) and structural trends for the 27,000-km2 area. The highest grades (anchimetamorphic) are associated with the oldest rocks (Honorat and Matapedia groups) exposed in the cores of major anticlines. Anchimetamorphic grades associated with the western outcrop belt of the Lower Devonian Fortin Group require 7–8 km of subsidence to accommodate sufficient thickness of overlying younger rocks (on top of 4–5 km of Fortin Group deep-water clastics) to explain the grades in terms of burial metamorphism assuming a geothermal gradient of 30° C km−1. The lowest-grade diagenetic rocks occupy a large area in the northeastern part of the peninsula, smaller areas in the northwestern part of the Acadian belt, in the centre of Chaleurs Bay synclinorium, and in the Ordovician Mictaw Group. The contact between the Taconian and Acadian belt is marked by a distinct maturation discontinuity. The Grand Pabos fault juxtaposes rocks of contrasting maturation levels (Matapedia Group against Fortin Group) in the west, but shows no maturation offset further east in the Honorat Group. The fault zone limiting the Fortin Group in the north is also associated with a major IC jump.

Notes: Abstract The assemblage muscovite-quartz-staurolite-aluminium silicate-biotite-garnet-chlorite with H2O (SABGC assemblage) is invariant in the K2O-FeO-MgO-Al2O3-SiO2-H2O (KFMASH) system. Such five-phase AFM assemblages should be absent in nature, but reported occurrences from at least ten localities suggest that either the assemblage internally controls μH2O or non-KFMASH components stabilize one or more of the phases.Least-squares regression analysis of minerals from South Royalton and Gassetts, Vermont, USA, demonstrates that subsets of the minerals in single SABGC assemblages from both localities are related by balanced reactions involving water. These results are consistent with the interpretation that the subassemblages fixed μH2O at an arbitrary, specified pressure and temperature. Balanced dehydration reactions also may be written between minerals in the SABGC assemblages and four-phase assemblages from the same outcrops interpreted to have equilibrated at the same pressures and temperatures as the five-phase assemblages. These results suggest that different specimens from the same outcrops equilibrated at different values of μH2O, supporting the conclusion that μH2O was not controlled externally. We could not demonstrate internal control of fo2 using measured mineral compositions because oxygen balance occurred in all reactions derived by regression.Regression analysis of published mineral compositions from New Mexico failed to identify balanced reactions involving water or oxygen either among the phases in a single SABGC assemblage or between SABGC and nearby four-phase assemblages. These results demonstrate that neither μH2O nor fo2 were fixed by the SABGC assemblages at these localities, and permit the interpretations that the assemblages were stabilized by the non-KFMASH components Na or Ca and that μH2O and fo2 were controlled externally.

Notes: Abstract Albite porphyroblasts are widely distributed in pelitic and semi-pelitic schists of the Fleur de Lys Supergroup, western Newfoundland. Textures and mineral assemblages indicate that albite grew during nearly isothermal decompression from P-T conditions of about 500° C, 9 kbar, to conditions of 550° C, 6.5 kbar. Three compositional varieties of albite-bearing schists, here termed PMAQ (paragonite-muscovite-albite-quartz), MMAQ (microcline-muscovite-albite-quartz), and PMMQ (paragonite-muscovite-margarite-quartz), can be distinguished on the basis of pre-porphyroblast mineral assemblages. Analysis of these assemblages in terms of the composition of the coexisting fluid [log a(Na+/H+) versus log a(K+/H+)] suggests that, as pressure and temperature changed, the stability field of albite expanded at the expense of coexisting matrix phyllosilicates. This promoted growth of albite on pre-existing or newly formed nuclei. Late oligoclase in PMAQ and PMMQ samples is associated with replacement of matrix garnet by plagioclase + mica ° Chlorite, particularly in strongly sheared samples.

Notes: Abstract Spinel-quartz-cordierite and spinel-quartz are found as relic prograde assemblages in Fe-rich granulites from the Araku area, Eastern Ghats belt, India. Subsequent reactions produced orthopyroxene + sillimanite in the former association and garnet + sillimanite in the latter. The first reaction is univariant in the FMAS system, but is trivariant in the present case because of the presence of Zn and Fe3+ in spinel. The second reaction also has high variance because of Zn and Fe3+, but also because of the presence of Ca in garnet. Thermobarometry shows that the metamorphic conditions were approximately 950° C and 8.5 kbar and the fo2 was near the NNO buffer. In Fe-rich bulk compositions and low-P-high-T conditions of metamorphism, two of the univariant reactions around the invariant point [Sa], namely (Sa, Hy) and (Sa, Cd), change topology due to reverse partitioning of Fe-Mg between coexisting garnet and spinel. An alternative partial petrogenetic grid in the system FMAS is constructed for such conditions and is applied satisfactorily to several sapphirine-free spinel granulites. It is shown that bulk composition (XFe and Zn) exerts greater control on the stability of spinel + quartz than fo2. The effect of the presence of Zn and Fe3+ in spinel on the proposed grid is evaluated. Reaction textures in the Araku spinel granulites can be explained from the petrogenetic grid as due to near-isobaric cooling.

Notes: The impure marbles of the internal Sesia-Lanzo Zone underwent a multi-stage metamorphic evolution of Alpine age and retain early-Alpine eclogitic assemblages, partially recrystallized under blueschist to greenschist facies conditions. These high-P assemblages consist of carbonates, phengite, quartz, omphacite, grossular-rich (locally spessartinic) garnet, zoisite and Al-rich titanite. Retrogressive stages are characterized by the growth of glaucophane, paragonite, phlogopite, tremolite and albite. Halogen-rich biotite and amphibole are also present. P-T estimates of the early-Alpine metamophism have been calculated from these unique high-P assemblages, in order to test the applicability of some calibrations to impure carbonate systems. In particular, some Gt-Cpx calibrations and the phengite geobarometer give results (T= 575 ± 45° C at 15 kbar for the eclogitic climax and T≤ 500° C at PH2O ≤ 9 kbar for early-Alpine retrogressive stages) which are within the range obtained from the surrounding lithologies.Phase relationships in P-T-XCO2 space indicate that mineral assemblages in the impure marbles coexisted with H2O-rich fluids (XCO2 〈0.03) during their entire Alpine evolution.

Notes: Analysis of the precision of the illite ‘crystallinity’technique shows that machine errors are 〈5%, while intra- and inter-sample errors are variable but are up to 12% and 14%, respectively (1σ). Consideration of this error analysis shows that the isocryst approach, which involves close contouring (e.g. 0.03 Δ2°) of illite ‘crystallinity’data, has a very low degree of confidence (〈0.5) and thus is not regarded as statistically valid. If contouring is to be undertaken with a high degree of confidence (〉0.8) it is necessary that contours should be at intervals of 0.1 ΔΘ2°, which is equivalent to subdivision of the anchizone into upper and lower units. Where previous interpretations have relied upon an isocryst method of contouring at less than 0.1 ΔΘ2° the conclusions must be regarded as unsubstantiated.Centrifuge separation of clay fractions (based on a Stokes’law application) gives separations in which a significant, but variable, percentage of grains have long axes greater than the size calculated. For the typical 〈2-μm fraction utilized, some 20% of grains lie in the 2–4-μm range, although the proportion is not believed to have a significant effect upon ‘crystallinity’values. The formula is applicable for grain-sizes down to 0.5 μm. Illite ‘crystallinity’values on samples prepared by an ultrasonic disaggregation method show a small increase on those prepared by ball mill crushing. The differences are minimal at the epi/anchizone level but increase to some 10% at the anchizone/diagenetic level. The effect on grade determinations is again thought to be minimal and indicates that concern over unsuitability of the ultrasonic disaggregation method is unfounded.

Notes: The amphibolite facies Puolankajärvi Formation (PjF) occupies the western margin of the Early Proterozoic Kainuu Schist Belt (KSB) of northern Finland. The lower and middle parts of the PjF consist of turbiditic psammites and pelites and tempestitic semipelites. This report concentrates on the pelitic lithologies which include quartz–two-mica–plagioclase schists with variable amounts of garnet, staurolite, andalusite and biotite porphyroblasts as well as sillimanite and cordierite segregations.The KSB forms a major north–south-trending synclinorium between two Archaean blocks. It contains both autochthonous and allochthonous units and is cut by faults and shear zones. The PjF lies on the western side of the KSB and is probably allochthonous. The formation has undergone six major deformation phases (D1, D2, D3a, D3b, D4 and D5). During D3a-D5 the maximum principal stress (σ1) changed in a clockwise direction from south-west to north-east. Between D2 and D3 the intermediate principal stress (σ2) changed from horizontal to vertical and the interval between D2 and D3 marks a transition from thrust to strike-slip tectonics.Relict structures in the porphyroblasts indicate the following mineral growth–deformation evolution in the PjF. (1) Throughout the PjF there was a successive crystallization of garnet (syn-D1), poryphyroblastic biotite (inter-D3/4) and staurolite (inter-D3/4) during the pre-D4 stage. (2) A syn-D4-inter-D4/5 crystallization of kyanite, sillimanite (fibrolite), porphyroblastic tourmaline, magnetite, rutile, cordierite and muscovite–biotite–plagioclase pseudomorphs after staurolite was most localized at and near D4 shear zones. (3) A syn- to post-D5 generation of andalusite, ilmenohematite and sheet silicates after staurolite and after cordierite occurred near D5 faults.The evolution outlined here permits the relative dating of the PjF parageneses, which is used in the second part of the study (Tuisku & Laajoki, 1990), and, together with the knowledge of the pressure–temperature conditions during various growth events, makes it possible to compile pressure–temperature–deformation paths for the PjF.

Notes: Petrographical and mineral chemical data are given for the eclogites which occur in the garnet-kyanite micaschists of the Penninic Dora-Maira Massif between Brossasco, Isasca and Martiniana (Italian Western Alps) and for a sodic whiteschist associated with the pyrope-coesite whiteschists of Martiniana. The Brossasco-Isasca (BI) eclogites are fine grained, foliated and often mica-rich rocks with a strong preferred orientation of omphacite crystals and white micas. Porphyroblasts of hornblende are common in some varieties, whilst zoisite and kyanite occur occasionally in pale green varieties associated with leucocratic layers with quartz, jadeite and garnet. These features differentiate the BI eclogites from the eclogites that occur in other continental units of the Western Alps, which all belong to type C. Garnet, sodic pyroxene and glaucophane are the major minerals in the sodic whiteschist.Sodic pyroxene in the eclogites is an omphacite often close to Jd50Di50, with very little acmite and virtually no AlIV, and impure jadeite in the leucocratic layers and in the sodic whiteschist. Garnet is almandine with 20–30 mol. % for each of the pyrope and grossular components in the eclogites and a pyrope-rich variety in the sodic whiteschist. White mica is a variably substituted phengite, and paragonite apparently only occurs as a replacement product of kyanite. Amphibole is hornblende in the eclogites, but the most magnesian glaucophane yet described in the sodic whiteschist. Quartz pseudomorphs of coesite were found occasionally in a few pyroxenes and garnets.The P-T conditions during the VHP event are constrained in the eclogites by reactions which define a field ranging from 27–28 kbar to 35 kbar and from 680 to 750° C. These temperatures are consistent with the results of garnet-pyroxene and garnet-phengite geothermometry which suggest that the eclogites may have equilibrated at around 700° C. In the sodic whiteschist pressures ranging from 29 to 35 kbar can be deduced from the stability of the jadeite-pyrope garnet-glaucophane compatibility. As in the eclogites water activity must have been low. Such conditions are close to the P-T values estimated for the early Alpine recrystallization of the pyrope-coesite rock and, like petrographical and mineralogical features, set aside the BI eclogites from the other eclogites of the Western Alps, instead indicating a close similarity to some of the eclogite bodies occurring in the Adula nappe of the Central Alps. An important corollary is that glaucophane stability, at least in Na- and Mg-rich compositions and under very high pressures, may extend up to 700° C, in agreement with the HT stability limit suggested by experimental studies.

Notes: The retrograde P-T trajectory of the eclogitic Fe-Ti-gabbros from the Ligurian Alps is constrained by the appearance of mineral parageneses post-dating the Na-clinopyroxene + garnet eclogitic assemblage and indicating the following sequence of metamorphic events: (1) amphibolitic stage— edenite/katophorite + plagioclase (An33–43) + oxides in symplectitic aggregates; (2) glaucophanic stage— a porphyroblastic glaucophanic amphibole has overgrown the symplectite, winchite also occurs as thin rims around glaucophane and both amphiboles are, sometimes, armoured by atoll garnets; (3) albite-amphibolite stage—barroisite/katophorite + albite + epidote + oxides ± chlorite overprint the glaucophanic stage minerals; (4) greenschist stage—represented by actinolite + albite + epidote + oxide paragenesis.The metamorphic evolution is complex and the decompression path, on a P–T diagram, is significantly different from those defined in the literature for the Voltri eclogites. The main features inferred from the P–T path are the following: (1) the pressure climax does not match the thermal climax, the maximum temperature conditions are in fact achieved during the early stage of uplift; (2) a decrease in temperature, suggested by the appearance of glaucophane after the amphibolitic symplectite; (3) successive uplift, probably accompanied by an increase in temperature. The complexity of the P-T path drawn for the Voltri eclogites can be explained with a mechanism of successive underthrusts propagating from the innermost to the outermost sector of the Ligurian Alps.

Notes: Within the Çokkul synform, Caledonian metamorphic rocks of the Middle Köli Nappe Complex (MKNC) are in low-angle fault contact with the basement mylonites derived from the Precambrian Tysfjord granite-gneiss. In the synform, the MKNC is composed of four fault-bounded nappes each of which has a distinct tectonic stratigraphy composed of amphibolite-facies metamorphosed pelitic and psammitic schists with minor lensoidal bodies of mafic and ultramafic rocks.Pelitic rocks from the three structurally lowest nappes contain the low-variance AFM mineral assemblages gar + bio + staur and staur + ky + bio with mu + qtz + ilm, whereas staur and ky are absent from the highest nappe, the Kallakvare nappe. AFM mineral assemblages in the three lowest nappes indicate peak metamorphic temperatures of 610–660°C and peak pressures in excess of 600 MPa. Mineral assemblages from the Kallakvare nappe are not as diagnostic of metamorphic grade. However, rocks from that nappe contain coexisting plagioclases from both sides of the peristerite gap, suggesting lower-grade peak P–T conditions than those of the structurally lower nappes. In addition, biotite from the lower nappes is more Ti-rich than biotite from the Kallakvare nappe. However, gar–bio–mu–plag and gar–bio–ky–plag–qtz thermobarometry suggests that all four nappes equilibrated at approximately 525 ± 25°C and 700 ± 100 MPa.Gibbs method thermodynamic modelling of garnet zoning profiles suggests that the lower three nappes followed clockwise P–T paths that involved heating and compression to a metamorphic peak of approximately 575–625°C, 800 MPa followed by cooling and decompression to 525°C, 700 MPa. P–T paths calculated for the Kallakvare nappe show decompression and minor heating to a peak T of 500–525°C. In the lower nappes, staur and ky grew during the heating phase not seen by the highest nappe. The outer parts of the paths from all four nappes are approximately parallel, possibly recording the emplacement of the Kallakvare nappe onto the already stacked lower three nappes at some time following the metamorphic peak. These P–T paths suggest that the sole fault of the Kallakvare nappe is a normal fault. Garnet zonation thus appears to record a previously unrecognized phase of uplift and tectonic thinning of the MKNC. This event appears to be restricted to the MKNC and to have occurred prior to the emplacement of the MKNC onto the Tysfjord granite-gneiss basement of Baltoscandia under greenschist-facies conditions. It may have been responsible for the uplift and cooling of the MKNC from 25–30 km amphibolite-facies conditions prior to its emplacement onto Baltoscandia under 15–20 km greenschist-facies conditions.The deformation zone associated with this normal fault is relatively narrow, generally less than 1 m thick. If this is typical of other detachment faults in the metamorphic infrastructure of the Scandinavian Caledonides, they may be relatively common, but not often recognized due to the detailed study needed to document them.

Notes: Numerical models of the progressive evolution of pelitic schists in the NCMnKFMASH system with the assemblage garnet + biotite + chlorite ± staurolite + plagioclase + muscovite + quartz + H2O are presented with the goal of predicting compositional changes in garnet and plagioclase along different P-T paths. The numerical models support several conclusions that should prove useful for interpreting the P-T paths of natural parageneses: (i) Garnet may grow along P-T vectors ranging from heating with decompression to cooling with compression. P-T paths deduced from garnet zoning that are inconsistent with these growth vectors are self-contradictory. (ii) There is a systematic relation between garnet and plagioclase composition and growth such that for most P-T paths, garnet growth requires plagioclase consumption. Furthermore, mass balance in a closed system requires that as plagioclase is consumed the remaining plagioclase becomes increasingly albitic. Inclusions of plagioclase in the core of garnet should be more anorthitic than those near the rim and zoned matrix plagioclase should have rims that are more albitic than the cores. Complex plagioclase textures may arise from the local variability of growth and precipitation kinetics. (iii) A decrease of Fe/(Fe + Mg) in a garnet zoning profile is a reliable indicator of increasing temperature for the assemblage modelled. However, there is no single reliable ΔP monitor and inferences about ΔP can only be made by considering plagioclase and garnet together. (iv) Consumption of garnet during the production of staurolite removes material from the outer shell of a garnet and may make recovery of peak metamorphic compositions and P-T conditions impossible. Low ‘peak’temperatures typically recorded by staurolite-bearing assemblages may reflect this phenomenon. (v) Diffusional homogenization of garnet affects the computed P-T path and results in a clockwise rotation of the computed P-T vector relative to the true P-T path.

Notes: The microstructures in the Erro-Tobbio peridotite indicate several stages of recrystallization of olivine + titanian clinohumite-bearing assemblages. The development of these assemblages is closely associated with serpentinite mylonites, in which they occur in shear bands and foliations and are inferred to have grown synkinematically, in veins, and as post-kinematic radial aggregates. In the peridotite wall-rock adjacent to these mylonites, the same assemblages have recrystallized statically at the expense of original olivine and pyroxenes, mesh-textured chrysolite and antigorite veins. In addition, the olivine-bearing assemblage occurs in widespread vein systems. The brittle deformation of the peridotite resulting in the development of these vein systems is closely related to ductile deformation of metagabbroic dykes in the peridotite. Although early metasomatism resulted in extensive rodingitization of the gabbros, some dykes show an eclogitic assemblage of Na-clinopyroxene + garnet + chloritoid + chlorite ± talc. These observations, the microstructures and the mineral chemistry all suggest that the assemblages in the ultramafic rocks and metagabbros developed during a prograde evolution towards high pressures (〉13–16 kbar, 450–550° C), and during subsequent decompression. This metamorphic evolution is considered to be related to Late Cretaceous intraoceanic subduction in the Alps-Apennine system and closure of the Piedmont-Ligurian basin.

Notes: A complete prograde P–T path, defined by 10 calculated P–T fields in succession, is recognized from metapelites by using geothermobarometry on garnet-bearing assemblages with microstructural control. Overstacking of several tectonic units during an early Variscan continental collision explains the complex prograde P–T history. Isostatic uplift and deformation controlled the retrograde P–T path.Deformation with changing character acted continuously during all stages of the evolution of the Austroalpine basement complex. After the intrusion of Caledonian granitoids, metapelites and magmatic rocks suffered a shearing deformation D1–D2, which produced sheath folds as well as the main foliation S2. Spessartine-rich first-generation garnets, situated in microlithons enclosed by S2, record the onset of shearing under increasing high-pressure–low-temperature conditions (7 kbar/380°C). Geothermobarometry on second-generation garnets which have been rotated during growth indicates isothermal decompression from 9 kbar to 5 kbar/500°C and subsequent recompression/heating during continuing shearing. This is explained by overthrusting of a tectonic unit (unit 2) from NE to SW upon the micaschist unit (unit 1), followed by isostatic uplift and further overstocking of a third unit (unit 3). The resulting Pmax of 12 kbar at 650°C and further increasing temperatures up to 680°C accompanied by decompression have been calculated using a third generation of garnets. These high-pressure–high-temperature conditions may explain the occurrence of eclogitic metabasites in adjacent regions.Staurolite and kyanite first appeared under decreasing pressures at the last stage of prograde P–T evolution. Shortening deformation D3 and simultaneous growth of typical amphibolite facies minerals (staurolite 2, kyanite 2, sillimanite, andalusite) occurred during the retrograde path. A final step of Variscan evolution was marked by an oppositely directed shearing D4 (at T 〉 300°C and P 〉 3 kbar), possibly indicating backthrusting or extension.Apart from acid intrusions, no signs of a previous Caledonian thermotectonic history were found in the area to the south of the Defereggen–Antholz–Vals Line.

Notes: Olivine-plagioclase coronas in metagabbros from the Adirondack Mountains, New York (USA) are spatially well-organized reaction textures consisting most commonly of sequential layers of orthopyroxene, clinopyroxene, plagioclase, and garnet; the textures are characteristic of diffusion-controlled reaction kinetics. Although similar coronas have been interpreted by previous workers in terms of an isochemical steady-state diffusion model, petrographical relations and material-balance calculations establish that coronas in the Adirondack metagabbros cannot be treated as isochemical and do not form in a single-stage steady-state process; instead they evolve through time in a complex open-system reaction.In this study, the isochemical diffusion model is modified to account for elemental fluxes across the outer boundaries of the coronal reaction band, thereby approximating the open-system behaviour of the coronas. The sequence and relative proportions of product minerals calculated by the open-system steady-state model correspond closely to those observed in coronas of the Adirondacks, over a wide range of values for the relative diffusivities of chemical components involved in the reaction, regardless of the particular method used to determine material balance in the reaction texture.Despite this correspondence, petrographical evidence for successive replacement of coronal product layers reveals that the Adirondack coronas evolved through one or more transient states, rather than forming in a single-stage steady-state process. There is no evidence that the successive replacement of coronal product layers resulted from changes in pressure or temperature, but there is petrographical evidence that these changes resulted from modification of the composition of reactant plagioclase as the corona-forming reaction proceeded. This is confirmed by the fact that the evolution of the coronas over time can be replicated with the open-system diffusion model by simulating the effect of the gradual exhaustion of plagioclase as a source of the Ca and Si components required for reaction. These simulations suggest that successive stages in the evolution of the coronas are characterized by these product sequences: (i) orthopyroxene-clinopyroxene-plagioclase-garnet; (ii) orthopyroxene-clinopyroxene-garnet; and (iii) orthopyroxene-garnet. All of these stages, and the transitions between them, are observed petrographically. Coronas in Adirondack metagabbros appear, therefore, to have originated in a complex, open-system, diffusion-controlled reaction in which the product assemblages changed as the reaction progressed.

Notes: Pseudotachylite veins have been found in the mylonite zone of the Hidaka metamorphic belt, Hokkaido, northern Japan. They are associated with faults with WNW-ESE to ENE-WSW or NE-SW trends which make a conjugate set, cutting foliations of the host mylonitic rocks with high obliquity. The mylonitic rocks comprise greenschist facies to prehnite-pumpellyite facies mineral assemblages. The mode of occurrence of the pseudotachylite veins indicates that they were generated on surfaces of the faults and were intruded as injection veins along microfractures in the host rocks during brittle deformation in near-surface environments. An analysis of the deformational and metamorphic history of the Hidaka Main Zone suggests that the ambient rock temperature was 200–300° C immediately before the formation of the Hidaka pseudotachylite.Three textural types of veins are distinguished: cryptocrystalline, microcrystalline and glassy. The cryptocrystalline or glassy type often occupies the marginal zones of the microcrystalline-type veins. The microcrystalline type is largely made up of quench microlites of orthopyroxene, clinopyroxene, biotite, plagioclase and opaque minerals with small amounts of amphibole microlites. The interstices of these microlites are occupied by glassy and/or cryptocrystalline materials. The presence of microlites and glasses in the pseudotachylite veins suggests that the pseudotachylites are the products of rapid cooling of silicate melts at depths of less than 5 km.The bulk chemical composition of the pseudotachylite veins is characterized by low SiO2 and a high water content and is very close to that of the host mylonitic rocks. This indicates that the pseudotachylite was formed by virtual total melting of the host rocks with sufficient hydrous mineral phases. Local chemical variation in the glassy parts of the pseudotachylite veins may be due to either crystallization of quench microlites or the disequilibrium nature of melting of mineral fragments and incomplete mixing of the melts. Pyroxene microlites show a crystallization trend from hypersthene through pigeonite to subcalcic augite with unusually high Al contents. The presence of pigeonite and high-Al pyroxene microlites, of hornblende and biotite microlites and rare plagioclase microlites may indicate the high temperature and high water content of the melt which formed the pseudotachylite veins. The melt temperatures were estimated to be up to 1100° C using a two-pyroxene geothermometer. Using published data relating water solubilities in high-temperature andesitic magmas to pressure, a depth estimate of about 4 km is inferred for the Hidaka pseudotachylites.Evidence derived from pseudotachylites in the Hidaka metamorphic belt supports the conclusion that pseudotachylite is formed by frictional melting along fault surfaces at shallow depths from rocks containing hydrous minerals.

Notes: The higher grade metamorphic zonation of the Sambagawa (= Sanbagawa) belt is established for the first time for the whole area of central Shikoku. As discontinuous reactions to define the isograd are absent, the metamorphic grade is primarily determined by the Mg-Fe partitioning between garnet and chlorite along representative traverses. However, for regional mapping, mineralogical features of the pelitic schists, such as using mineral assemblages of more than divariant equilibrium, the modal garnet to chlorite ratio, and the optical properties of chlorite, are employed as auxiliary criteria.The presence of the highest grade mineral zone in the middle of the structural level is confirmed, but its spatial distribution is far more complex than hitherto accepted. Thermal axes are now confirmed at three different structural levels. A model is presented in which the stacking of thrust sheets of different grade took place while metamorphic reactions were in progress. Thermal readjustment brought a continuous metamorphic temperature gradient across and within the thrust sheets. Tectonic blocks of metagabbro and ultramafic rock were emplaced synchronously with thinning and subsequently also re-equilibrated. Local anomalies of metamorphic grade, represented by mixing of schists of different metamorphic grade, exist, but they are due to a later stage event.

Notes: Low-pressure metamorphic facies (i.e. high T/P ratios) are widespread in a wide range of tectonic settings. Explanations offered for the occurrence of these facies include extensional and/or magmatic models. However, these fail to explain that the low-P facies metamorphism is commonly coeval with a phase of pervasive crustal thickening, with T/P ratios increasing during, or slightly lagging behind, the thickening. We propose an alternative explanation based on the approximate synchroneity of crustal thickening and erosion (thinning) of the mantle lithosphere.

Notes: In the Proterozoic Mary Kathleen Fold Belt, northern Australia, infiltration of large volumes of externally derived fluid occurred synchronously with regional amphibolite-facies metamorphism and deformation. This paper develops a model of structurally controlled fluid migration by comparing the distribution of fossil fluid pathways with the inferred stress and strain patterns during the deformation. Intense fluid flow was localized within strong, relatively brittle meta-intrusive bodies, and in discrete, veined, brecciated and altered zones around their margins. In metasediments folded in a ductile manner outside these areas, fluid infiltration was negligible. The direct correlation between structural styles and the magnitude of veining and metasomatism suggests control of permeability enhancement, and hence fluid flow, by deformation. Finite difference modelling of a strong body in a weaker matrix has been used to evaluate the variation of stresses during the deformation, from which it is clear that stress and strain heterogeneities have systematically influenced the development and maintenance of metamorphic fluid pathways. Particular regions in which mean stress may be significantly lower than the average lithostatic pressures include the ‘strain shadow’zones adjacent to the strong bodies, other dilatant zones around the bodies, and the bodies themselves. This geometry is favourable not only for localized brittle deformation under amphilobite facies conditions, but also for focused fluid flow in the low mean stress regions, as evidenced by the abundance of veins. Fluid access through these metamorphic aquifers occurred during tensile failure episodes, with particularly large dilations and decimetre-scale veining in areas of strain incompatibility. It appears likely that fluid circulated many times through the Fold Belt, with flow concentrated in the metamorphic aquifers. A model is developed that explains both the structurally focused fluid flow and the postulated multi-pass recirculation by dilatancy pumping, the ‘pump engines’comprising the low mean stress zones.

Notes: An Early Palaeozoic (Ordovician ?) metamudstone sequence near Wojcieszow, Kaczawa Mts, Western Sudetes, Poland, contains numerous metabasite sills, up to 50 m thick. These subvolcanic rocks are of within-plate alkali basalt type. Primary igneous phases in the metabasites, clinopyroxene (salite) and kaersutite, are veined and partly replaced by complex metamorphic mineral assemblages. Particularly, the kaersutite is corroded and rimmed by zoned sodic, sodic–calcic and calcic amphiboles. The matrix is composed of actinolite, pycnochlorite, albite (An ≤ 0.5%), epidote (Ps 27–33), titanite, calcite, opaques and, occasionally, biotite, phengite and stilpnomelane.The sodic amphiboles are glaucophane to crossite in composition with NaB from 1.9 to 1.6. They are rimmed successively by sodic–calcic and calcic amphiboles with compositions ranging from magnesioferri-winchite to actinolite. No compositions between NaB= 0.92 and NaB= 1.56 have been ascertained.The textures may be interpreted as representing a greenschist facies overprint on an earlier blueschist (or blueschist–greenschist transitional) assemblage. The presence of glaucophane and no traces of a jadeitic pyroxene + quartz association indicate pressures between 6 and 12 kbar during the high-pressure episode. Temperature is difficult to assess in this metamorphic event. The replacement of glaucophane by actinolite + chlorite + albite, with associated epidote, allows restriction of the upper pressure limit of the greenschist recrystallization to 〈8 kbar, between 350 and 450°C. The mineral assemblage representing the greenschist episode suggests the P–T conditions of the high-pressure part of the chlorite or lower biotite zone. The latest metamorphic recrystallization, under the greenschist facies, may have taken place in the Viséan.

Notes: Using the experimental data on Fe–Mg exchange between orthopyroxene and biotite of Fonarev & Konilov (1986), an orthopyroxene–biotite geothermometer is developed. The thermometer is corrected for mixing of Ti and Al in octahedral sites in biotite and also for non-ideal mixing of Fe and Mg in orthopyroxene. The thermometer is applied to several amphibolite–granulite transition facies and granulite facies rocks and also to mantle xenoliths. It yields consistent results in rocks of widely varying bulk composition, and highly magnesian mantle xenoliths. This thermometer removes the difficulty of estimating temperature in garnet-free rocks in high-grade terrains and also provides independent estimates of temperature in garnet-bearing assemblages.

Notes: The Omeo Metamorphic Complex forms the southern end of the Wagga Metamorphic Belt, which is the main locus of Palaeozoic low-pressure metamorphism in the Lachlan Fold Belt, south-eastern Australia. It comprises metamorphosed Ordovician quartz-rich turbidites originally derived from Precambrian cratonic rocks. Prograde regional metamorphism occurred in the early Silurian, very soon after sedimentation had ceased. The sequence of metamorphic zones, with increasing grade, is: chlorite, biotite, cordierite, andalusite–K-feldspar and sillimanite–K-feldspar. Migmatites occur in the sillimanite–K-feldspar zone, but large bodies of S-type granite were derived from rocks underlying the exposed Ordovician sequence. P and T estimates for the highest grade rocks are T= 700°C and P= 3.5 kbar, indicating a very high P–T gradient of 65°C/km.The high heat flow during prograde metamorphism probably resulted from a combination of a thermal anomaly persisting from a pre-metamorphic back-arc basin environment, and intrusion of hot, mantle-derived magmas into the lower and middle crust.Regional retrograde metamorphism coincided with a general reheating of the crust in the Siluro-Devonian, accompanied by intrusion of many I-type plutons and resetting of the K–Ar dates of some earlier plutons. The Omeo Metamorphic Complex was exposed to erosion at this time.

Notes: The Narryer Gneiss Complex of the Yilgarn Block is a key segment of the Western Australian Precambrian Shield. It is a regional granulite facies terrain comprised of predominantly quartzo-feldspathic gneisses derived from granitic intrusions c. 3.6–3.4 Ga old. Granulite facies metamorphism occurred c. 3.3 Ga ago, and conditions of 750–850°C and 7–10 kbar are estimated for the Mukalo Creek Area (MCA) near Errabiddy in the north. The P–T path of the MCA has been derived from metamorphic assemblages in younger rocks that intruded the gneisses during at least three subsequent events, and this path is supported by reaction coronas in the older gneisses. There is no evidence for uplift immediately following peak metamorphism of the MCA, and a period of isobaric cooling is inferred from the pressures recorded in younger rocks. Pressures and temperatures estimated from metadolerites, which intruded the older gneisses during ‘granite–greenstone’tectonism at about 2.6 Ga and during early Proterozoic thrusting show that the Errabiddy area remained in the lower crust, although it was probably reheated during the younger events. Isothermal uplift to upper crustal levels occurred at c. 1.6 Ga ago, and was followed by further deformation and patchy retrogression of high-grade assemblages. The effects of younger deformation, cooling and reheating can be discerned in the older gneisses, but as there has been no pervasive deformation or rehydration, the minerals and microstructures formed during early Archaean granulite facies metamorphism for the most part are retained.The MCA remained in the lower crust for about 1700 Ma following peak metamorphism and some event unrelated to the original metamorphism was required to exhume it. Uplift occurred during development of the Capricorn Orogen, when some 30–35 km were added to the crust beneath the Errabiddy area. The recognition of early Proterozoic thrusting, plus crustal thickening, suggests that the Capricorn Orogen is a belt of regional compression which resulted from convergence of the Yilgarn and Pilbara Cratons.

Notes: We present, as a progress report, a revised and much enlarged version of the thermodynamic dataset given earlier (Holland & Powell, 1985). This new set includes data for 123 mineral and fluid end-members made consistent with over 200 P–T–XCO2–fO2 phase equilibrium experiments. Several improvements and advances have been made, in addition to the increased coverage of mineral phases: the data are now presented in three groups ranked according to reliability; a large number of iron-bearing phases has been included through experimental and, in some cases, natural Fe:Mg partitioning data; H2O and CO2 contents of cordierites are accounted for with the solution model of Kurepin (1985); simple Landau theory is used to model lambda anomalies in heat capacity and the Al/Si order–disorder behaviour in some silicates, and Tschermak-substituted end-members have been derived for iron and magnesium end-members of chlorite, talc, muscovite, biotite, pyroxene and amphibole.For the subset of data which overlap those of Berman (1988), it is encouraging to find both (1) very substantial agreement between the two sets of thermodynamic data and (2) that the two sets reproduce the phase equilibrium experimental brackets to a very similar degree of accuracy. The main differences in the two datasets involve size (123 as compared to 67 end-members), the methods used in data reduction (least squares as compared to linear programming), and the provision for estimation of uncertainties with this dataset. For calculations on mineral assemblages in rocks, we aim to maximize the information available from the dataset, by combining the equilibria from all the reactions which can be written between the end-members in the minerals. For phase diagram calculations, we calculate the compositions of complex solid solutions (together with P and T) involved in invariant, univariant and divariant assemblages. Moreover we strongly believe in attempting to assess the probable uncertainties in calculated equilibria and hence provide a framework for performing simple error propagation in all calculations in thermocalc, the computer program we offer for an effective use of the dataset and the calculation methods we advocate.

Notes: In a granulite-facies spinel-bearing quartzite, corundum, orthopyroxene and sapphirine (and rarely cordierite and sillimanite) form partial rims separating spinel from quartz. Textures indicate the reactions:spinel + quartz = orthopyroxene + corundum, andspinel + quartz = orthopyroxene + sapphirine.Thus, corundum and sapphirine are produced by reactions involving quartz. The low Al-content of the orthopyroxene (0.5–2.8 wt %) and low values for Mg–Fe distribution coefficient for spinel–sapphirine and spinel–orthopyroxene reflect low-temperature conditions during formation of the reaction products. Absence of zoning in spinel and a constant Mg–Fe distribution coefficient for spinel–sapphirine and spinel–orthopyroxene, over a compositional range, indicate Mg–Fe equilibration. It is suggested that stable reactions such as spinel + quartz = cordierite or spinel + quartz = garnet + sillimanite were over-stepped and that metastable reactions give rise to the anomalous juxtaposition of corundum + quartz.

Notes: Abstract In well NJ-15 of the Nesjavellir geothermal field, Iceland, the transition of discrete smectite into discrete chlorite has been studied from drill cuttings recovered at depths of less than 1714 m and over a continuous range of temperatures between 60 and 300° C. At temperatures below 180° C, the clay fractions contain mixtures of di- and trioctahedral smectites, whose layer charge increases with depth. Between 200 and 240° C, discrete smectites have transformed into smectite-rich, randomly interstratified chlorite and smecite (R0 C/S). Because the abundance of chlorite interlayers in this C/S is generally 〈20%, its presence can be detected only by electron microprobe techniques and not by X-ray diffraction. Between 245 and 265° C, both regularly (R1) and randomly interstratified C/S are the predominant layer silicates. Discrete chlorite first appears at approximately 270° C and coexists with minor amounts of R0 C/S at higher temperatures. R0 and R1 C/S form a nearly complete compositional series between trioctahedral saponite and discrete chlorite end-members. The interlayer cation and Si content of smectites and C/S decrease with increasing temperature. The Mg/(Mg + Fe) content of smectite, C/S, and chlorite is unrelated to temperature. The percentage of chlorite in C/S, as determined by electron microprobe analyses, increases continuously with increasing temperature, except for occurrences of smectite-rich C/S in fresh basaltic dykes which have not thermally equilibrated with the higher grade country rocks.

Notes: Abstract Fairly strong (r= 0.75–0.85) positive linear correlations were found between crystallinity indices (peak widths) measured on the first two basal reflections of chlorite and those of illite–muscovite in 〈2-μm fractions of a representative shale–slate–phyllite series from Palaeozoic and Mesozoic formations of northeast Hungary. The metamorphic grade ranges from late or deep diagenesis through anchizone to epizone conditions. Chlorite crystallinity values measured on air-dried and ethylene-glycol-solvated samples suggest that the effects of expandable interlayers are negligable, especially in the higher grade (∼temperature) part of the series. However, the greater scattering of crystallinity values for the chlorite 001 reflection compared to those of the 002 reflection may be related to the effects of minor amounts of interlayered and/or discrete smectite and/or vermiculite. With increasing metamorphic grade and advancing equilibrium recrystallization, the chlorite compositions in different samples become more homogenous. No correlation exists between crystallinity and changes in chlorite composition as estimated from the intensity ratios of basal reflections. Hence an increase of domain size and a decrease of lattice distortion with increasing grade (∼temperature) may be decisive factors affecting chlorite crystallinity.Chlorite crystallinity can be applied as a reliable regional, statistical technique complementary with, or instead of, the illite crystallinity method. The illite and chlorite crystallinity scales used here are related to Kübler's epi-, anchi- and diagenetic zones and correlated with coal rank, conodont colour alteration and mineral facies data. As the effects of the detrital white mica can be observed even in the 〈2-μm fractions of anchizonal metapelites, the anchizone boundaries determined solely on the base of ‘fixed’illite crystallinity values may vary with amounts of detrital and newly formed muscovite–illite. Hence a complex approach utilizing more than one method for determination of grade is preferred for petrogenetic purposes, even if relationships between crystallinity scales, coal rank and mineral facies also vary strongly in different tectonic settings and lithologies.

Notes: Abstract Illite crystallinity (IC) and other indicators of the grade of very-low-grade metamorphism associated with the appearance of various stages of slaty cleavage in phyllosilicate-rich rocks have been compiled from a wide variety of terranes. IC values have been converted to a Kübler-equivalent standard scale, but the diverse characterizations of the cleavage fabrics in published descriptions do not always allow an unequivocal identification of equivalent stages of cleavage development.Nevertheless, there exists a distinct relationship between grade and the appearance of various stages of cleavage development.(1) Indications of incipient slaty cleavage, such as S0–S1 pencil structure, appearance of primary (S1) crenulation cleavage and of closely-spaced cleavage without parallel fabric in the microlithons, is associated with a wide range of mostly medium- and high-grade diagenetic IC values.(2) The appearance of smooth cleavage with a strong parallel fabric in the microlithons and/or quartz–mica ‘beards’and the chlorite–mica stacks shortened at a high angle to (001), and of irregular cleavage in sandy beds is associated with a much narrower range of predominantly low- and medium-grade anchimetamorphic grades (rarely high-grade diagenetic). The first appearance of these stages of cleavage development with higher grades can often be related to post-kinematic magmatic heating, polymetamorphism (pre-cleavage metamorphism), or ‘static’recrystallization without cleavage formation, for example in low-strain zones.There exists a relationship between finite strain, fabric and metamorphic grade in mudstones and slates; in coarser clastic rocks the same finite strain–fabric relationship occurs at appreciably higher grades. A relationship between finite strain in carbonate rocks and IC in the nearby rocks has been reported from the Helvetic zone of the Swiss Alps.The earlier stages of cleavage formation are associated with little improvement in IC; the narrow range of IC associated with smooth cleavage is concluded to represent recrystallization and grain growth concurrent with cleavage formation.

Notes: Distinctive lithological associations and geological relationships, and initial geochronological results indicate the presence of an areally extensive region of reworked Archaean basement containing polymetamorphic granulites in the Rauer Group, East Antarctica.Structurally early metapelites from within this reworked region preserve complex and varied metamorphic histories which largely pre-date and bear no relation to a Late Proterozoic metamorphism generally recognized in this part of East Antarctica. In particular, magnesian metapelite rafts from Long Point record extreme peak P–T conditions of 10–12 kbar and 100–1050°C, and an initial decompression to 8 kbar at temperatures of greater than 900°C. Initial garnet–orthopyroxene–sillimanite assemblages contain the most magnesian (and pyrope-rich) garnets (XMg= 0.71) yet found in granulite facies rocks. A high-temperature decompressional P–T history is consistent with reaction textures in which the phase assemblages produced through garnet breakdown vary systematically with the initial garnet XMg composition, reflecting the intersection of different divariant reactions in rocks of varied composition as pressures decreased. This history is thought to relate to Archaean events, whereas a lower-temperature (c. 750–800°C) decompression to 5 kbar reflects Late Proterozoic reworking of these relict assemblages.The major Late Proterozoic (c. 1000 Ma) granulite facies metamorphism is recorded in a suite of younger Fe-rich metapelites and associated paragneisses in which syn- to post-deformational decompression, through 2–4 kbar from maximum recorded P–T conditions of 7–9 kbar and 800–850°C, is constrained by geothermobarometry and reaction textures. This P–T evolution is thought to reflect rapid tectonic collapse of crust previously thickened through collision.

Notes: In the southeastern Reynolds Range, central Australia, a low-P granulite facies metamorphism affected two sedimentary sequences: the Lander Rock Beds and the Reynolds Range Group. In the context of the whole of the Reynolds Range and the adjacent Anmatjira Range, this metamorphism is M3 in a sequence M1–4 that occurred over a period of 250 Ma. In particular, M1 affected the Lander Rock Beds prior to the deposition of the Reynolds Group. M3 has an areally restricted, high-grade area in the southeastern Reynolds Range, affecting both the Reynolds Range Group and the underlying Lander Rock Beds. The effects of M3 are characterized by spinel + quartz-bearing peak metamorphic assemblages in metapelites, which imply peak conditions of ≥750°C and 4.5 ± 1 kbar, and involved isobaric cooling or compression with cooling. It is concluded that one of a series of thermal perturbations caused by thinning of mantle lithosphere contemporaneous with crustal thickening was responsible for M3. In the southeastern Reynolds Range, evidence of both the unconformity between the two rock groups and previous metamorphism/deformation has been completely erased by recrystallization during M3–D3.

Notes: On the basis of fluid inclusion evidence, pervasive influx of deep-seated CO2-rich fluids has been invoked to account for mid- to upper amphibolite facies (M2B) metamorphism on the island of Naxos (Cyclades, Greece). In this paper, mineral devolatilization and melt equilibria are used to constrain the composition of both syn- and post-peak-M2B fluids in the deepest exposed levels of the metamorphic complex. The results indicate that peak-M2B fluids were spatially and compositionally heterogeneous throughout the high-grade core of the complex, whereas post-peak-M2B fluids were generally water-rich. The observed heterogeneities in syn-M2B fluid composition are inconsistent with pervasive CO2-flushing models invoked by previous workers on the basis of fluid inclusion evidence. It is likely that few CO2-rich fluid inclusions on Naxos preserve fluids trapped under peak metamorphic conditions. It is suggested that many of these inclusions have behaved as chemically open systems during the intense deformation that accompanied the uplift of the metamorphic complex. A similar process may explain the occurrence of some CO2-rich fluid inclusions in granulite facies rocks.

Notes: A detailed high-pressure experimental study of two mafic xenoliths, in which coexisting garnet and clinopyroxene (± plagioclase, spinel and olivine) were crystallized over a P–T range of 10–30 kbar and 950–1200°C, has revealed significant differences in temperatures from those estimated for coexisting garnets and clinopyroxenes using the Ellis & Green Fe–Mg exchange thermometer. The results show perfect matching at 30 kbar, 1150–1200°C, but increasing deviation at lower pressure and lower temperature, with the Ellis & Green calibration reaching a ΔT (overestimate) of c. 145°C at 10–12 kbar and 950°C. The grossular content of the garnet increases from c. 21 mol.% at 10 kbar to 26–31 mol.% at 30 kbar. These results confirm other recent experimental studies that show that the pressure correction, and possibly to a lesser extent the correction for grossular content, applied by Ellis & Green, are not appropriate for lower pressure conditions, and give estimated temperatures that are significantly high when applied to granulitic terranes formed at c. 10 kbar. The new reconnaissance results allow a graphical interpolation of a garnet–clinopyroxene geothermometer based on the Fe–Mg exchange reaction which should be applicable to assemblages formed under lower crustal conditions.

Notes: The Main Zone of the Hidaka Metamorphic Belt is an uplifted crustal section of island-arc type. The crust was formed during early Tertiary time, as a result of collision between two arc–trench systems of Cretaceous age. The crustal metamorphic sequence is divided into four metamorphic zones (I–IV), in which zone IV is in the granulite facies.A detailed study of the evolution of the Hidaka Belt, based on a revised P–T–t analysis of the metamorphic rocks, notably a newly found staurolite-bearing granulite, confirms a prograde isobaric heating path, after a supposed event of tectonic thickening of accretionary sedimentary and oceanic crustal rocks. During the peak metamorphic event (c. 53 Ma), the regional geothermal gradient attained 33–40° C km−1, and the highest P–T condition obtained from the lowest part of the granulite unit is 830° C, 7 kbar. In this part, XH2O of Gt–Opx–Cd gneiss is about 0.15 and that of Gt–Cd–Bt gneiss is 0.4. The P–T–XH2O condition of the granulite unit is well within a field where fluid-present partial melting of pelitic and greywacke metamorphic rocks takes place. This is in harmony with the restitic nature of the Gt–Opx–Cd gneiss in the lowest part of the granulite unit.The possibility that partial melting took place in the Main Zone is significant for the genesis of the peraluminous (S-type) granitic rocks within it. The S-type granitic rocks in this zone are Opx–Gt–Bt tonalite in the granulite zone, Gt–Cd–Bt tonalite in the amphibolite zone, and Cd–Bt–Mus tonalite in the Bt–Mus gneiss zone. The mineralogical and chemical nature of these strongly peraluminous tonalitic rocks permit them to be regarded as having been derived from S-type granitic magma generated by crustal anatexis of pelitic metamorphic rocks in deeper crust.

Notes: The paragenetic relationships between sillimanite, andalusite, kyanite, chlorite, cordierite, biotite, garnet and staurolite in the Early Proterozoic Puolankajärvi Formation (PjF), together with mineral compositions, are used to construct a partial petrogenetic grid for metapelites with significant Mn content (MnO = 0.1–0.5%) by adding a six-phase invariant point over the garnet-absent invariant point for Mn-free AMF-phases.The grid and textural relations of the PjF are used to construct part of the P–T–deformation path for the PjF. Relatively short deformation pulses and associated flow of oxidizing fluid along shear zones were responsible for the paragenetic and compositional changes during cooling and decompression at 600–500°C and 6.0–2.5 kbar. Oxidation led to decreased Fe2+ and further stressed the importance of Mn (increased Mn/divalent cations).A tectonothermal evolution of the Kainuu Schist Belt is presented which includes crustal thinning and steepening of a previously established thermal gradient. This was followed by thrusting and folding of the isotherms into a thermal antiform on the western side of the belt.

Notes: The alkalic Scituate Granite was emplaced into crystalline sequences within the New England Esmond–Dedham terrane in the Late Devonian (c. 370 Ma). Variably recrystallized amphibole (iron-rich, hastingsite–hastingsitic hornblende) from four variably deformed samples of the pluton record south-westerly younging 40Ar/39Ar plateau ages ranging between 276 and 263 Ma. These are interpreted to date diachronous cooling through temperatures appropriate for intracrystalline retention of argon following late Palaeozoic orogenic activity. Iron-rich biotite concentrates from the samples record only slightly younger ages, and therefore suggest relatively rapid post-metamorphic cooling. The 40Ar/39Ar ages indicate that the late Palaeozoic tectonothermal overprint was much more regionally pervasive than was previously considered. The apparent timing of this activity is similar to previous estimates for the chronology of high-grade metamorphism throughout the adjacent Hope Valley terrane and for phases of ductile movement on the intervening Lake Char–Honey Hill fault system.

Notes: Aluminous reaction textures in orthoamphibole-bearing rocks from the Froland area, Bamble, south Norway, record the prograde pressure–temperature path of the high-grade Kongsbergian Orogeny (c. 1600–1500 Ma) and the low–mid amphibolite facies overprint during the Sveconorwegian Orogeny (c. 1100–1000 Ma). The rocks contain anthophyllite/gedrite, garnet, cordierite, biotite, quartz, andalusite, kyanite, Cr-rich staurolite, tourmaline, ilmenite, rutile and corundum in a variety of parageneses. The P–T path is deduced from petrographic observations, mineral chemistry and zoning, geothermometry and (N)FMASH equilibria. The results indicate the sequence of metamorphic stages outlined below. (a) An M1 phase characterized by the presence of strongly deformed andalusite, gedrite and tourmaline.(b) An M2 phase with the development of kyanite after andalusite and the growth of staurolite associated with strong Na–Al–Mg zoning in orthoamphibole, indicating an increase in pressure (4 8 kbar) and temperature (500° 650°C).(c) Pressure decrease at high P (6–7 kbar) and high T (600–700 °C) during M3a with the production of cordierite ° Corundum between kyanite, staurolite and orthoamphibole and cordierite growth between corundum and orthoamphibole.(d) Temperature increase to 740 ± 60 °C and 7 kbar; static growth of garnet (M3b) at the metamorphic climax (peak T). The heat supply necessary to explain the temperature increase between the M3a and M3b phases is correlated with synkinematic enderbitic–charnockitic and basic intrusions in the Arendal granulite facies terrain.(e) M3b metamorphic conditions were followed by an initial isobaric cooling path (early M4) and late-stage pressure decrease (late M4). Early M4 conditions of 6–7 kbar and 550–600 °C, assuming PH2O 〈 Ptotal are indicated by a retrograde talc–kyanite–quartz assemblage in late quartz–cordierite veins. Late M4 conditions of 3–4 kbar and 420–530 °C are inferred from a kyanite–andalusite–chlorite–quartz assemblage in vein-cordierite. The M1–M3 stages are interpreted as being the result of the same metamorphic P–T path, which was caused by both tectonic and magmatic thickening. A prolonged crustal residence time is proposed for the Bamble sector before uplift during the later stages of M4 occurred.

Notes: Instrumental settings for determination of illite/muscovite ‘crystallinity’(half-height width of the 10-Å X-ray diffraction peak) and the limits of the anchimetamorphic zone adopted by various authors fall into several groups.The variation in the limiting peak widths between the authors that have adopted Kubler's Neuchâtel boundary values of 0.42° and 0.25°Δ2θ can be interpreted in terms of variation in the instrumental settings. The choice of time constants higher than those given by the formula causes peak broadening; this effect is particularly marked at high scan rates. The peak broadening is by constant increments that are virtually independent of the absolute peak width.The differences between the Kubler (Neuchâtel)-derived limiting values and some other scales are appreciably greater than can be accounted for by these differences in instrumental settings: many of these scales are not equivalent. In particular, the limits adopted by Dunoyer de Segonzac (1969) and subsequent workers at Strasbourg are too broad; their anchizone represents a range of grades of metamorphism lower than that of Kubler, widely overlapping the latter's ‘diagenetic’zone. Those adopted by some other, mainly French, authors are too narrow.The limits of the anchizone should be calibrated by inter-laboratory standards, and the instrumental settings should be specified in full.

Notes: A combination of fluid inclusion, stable isotope and geochemical techniques has been used to study the nature of fluids present and their behaviour during Caledonian low-grade metamorphism of the Harlech Dome, north Wales. Fluid inclusion studies show that in most of the metasedimentary sequence the peak metamorphic fluid was an aqueous Na–K–Cl brine but in the graphitic Clogau Formation and in parts of the overlying Maentwrog Formation immiscible H2O-rich and CH4-rich fluids coexisted.Late-stage inclusions are of calcium-rich brine and a dilute aqueous fluid. The chemical composition of chlorite in metamorphic veins and rocks varies between different formations and quartz-oxygen isotopic compositions show considerable variation between different units. Both of these features are taken to indicate that there was little or no pervasive movement of fluid between different units at the peak of metamorphism. After the metamorphic peak there was focused flow of fluid upward through the sequence along fractures, in response to end-Caledonian uplift and unloading. Where the migrating fluid crossed the graphitic shales, interaction between the fluid and the shales gave rise to the formation of the auriferous veins of the Dolgellau Gold Belt. Subsequent to this mineralizing event there was widespread development of 18O-enriched calcites and micas.In the case of vein minerals it is possible that these crystallized directly from late-stage fluids at lower temperature than the quartz in the same veins. Alternatively, the original vein minerals may have re-equilibrated with later 18O-enriched or cooler fluid. In the case of muscovites in the rock matrix it is proposed that the isotopically heavy compositions are the result of re-equilibration of initially light grains with an introduced fluid, requiring considerable influx of fluid. This event may relate to either of two late-stage fluids observed as inclusions.

Notes: Abstract In granulite facies metapelitic rocks in the Musgrave Complex, central Australia, reaction between S1 garnet and sillimanite involves the development in S2 of both garnet + cordierite + hercynitic spinel + biotite and hercynitic spinel + cordierite + sillimanite + biotite. The S2 assemblages occur either in coronas and symplectites, mainly around garnet, or, in rocks in which S2 is more strongly developed, as recrystallized assemblages. Ignoring the presence of biotite and ilmenite, the mineral textures can be accounted for qualitatively by a consideration of the model system FeO-MgO-Al2O3-SiO2 (FMAS); the textural relationships accord with decompression accompanying the change from S1 to S2. However, since biotite and ilmenite are involved in the assemblages, the parageneses are better accounted for in terms of equilibria in the expanded model system K2O-FeO-MgO-Al2O3-SiO2-H2-TiO2-Fe2O3 (KFMASHTO), i.e. AFM + TiO2+ Fe2O3. The coronas reflect the tectonic unroofing of at least part of the Musgrave Complex from peak S1 conditions of about 8 kbar to S2 conditions of about 4 kbar.

Notes: Abstract During the Eocene-Oligocene, the Indian plate collided with the Kohistan arc along the Main Mantle Thrust (MMT) zone. The structure of the Lower Swat rock sequence, on the Indian plate directly south of the MMT, is a dome with a basement of granitic gneiss and quartz-rich schist unconformably overlain by amphibolitic and calcareous schist. The earliest superposed small-scale folds (F1 & F2) represent a progressive F1/F2 deformation that is associated with a single set of WSW-vergent large-scale folds (termed F2). These folds are inferred to have developed during oblique, WSW-directed overthrusting of the MMT suture complex onto the Lower Swat rock sequence. Metamorphism began during F1/F2 as indicated by an S1 foliation that developed during biotite-grade metamorphism. S1 is preserved as a relict texture in porphyroblasts that grew during a subsequent interkinematic phase during garnet- and higher grade metamorphism. The dominant, regional foliation (S2) developed following the interkinematic phase. S2 is associated with transposition of S1 and rotation or dismemberment of porphyroblasts. Annealing recrystallization followed S2 and continued during F3 thereby destroying or masking possible pre-existing stretching fabrics. Superposed F3 folds are upright and open with N-S axial trends. They may correlate with early doming of the Lower Swat rock sequence and with strike-slip displacement in the northern part of the MMT zone, north of the Lower Swat area. F3 was followed by retrograde metamorphism and development of E-W-trending, S-vergent F4 folds. F4 may be associated with a final phase of southward directed thrusting and inactivity in the MMT zone. Correlation of published 40Ar/39Ar ages with the metamorphic fabrics suggests that F1/F2 and F3 occurred in the Eocene, and that F4 developed in the Oligocene. F4 is the earliest indication of southward verging structures on this part of the Indian plate.

Notes: Granulites exposed in the Reinbolt Hills, East Antarctica, are part of the extensive Late Proterozoic granulite complex of East Antarctica, which includes the Rauer Group to the east and the northern Prince Charles Mountains to the west. The deformation history includes three pervasive deformation phases. No chemical or mineralogical distinction between these phases has been detected and this is interpreted to be the result of complete re-equilibration at the end of the third deformation phase. Two late deformation phases post-date the metamorphism and record a medium-temperature cooling path. A short segment of the P–T path of these rocks was inferred from mineral reactions that occurred during these late deformation phases. The path passes from 800°C, 7 kbar to 690°C, 5 kbar, indicating strong decompression, which is typical of a thrust-dominated crustal thickening followed by rapid erosion or extensional collapse.

Notes: Mafic granulite, garnet amphibolite and charnockite occur in the southwest Swedish part of the Baltic Shield. This part is generally considered to be the continuation of the Grenville collisional belt in Canada. The area with granulite facies rocks, the Southwest Swedish Granulite Region (SGR), is considerably larger than previously thought. The SGR is bounded to the east and west by two major tectonic zones. The first quantitative age data and P–T determinations for the high-grade metamorphism in the SGR are presented.Conventional geothermobarometry was applied to mafic granulites from five localities. The estimated P–T conditions for the peak of metamorphism range from 705°C and 8.1 kbar at Hallandsås in the south, to 770°C and 10.5 kbar at Ullared in the north (medium- to high-P granulite facies conditions). Sm–Nd geochronology on minerals from the mafic granulites at Hallandsås and Ullared give late Sveconorwegian (Grenville) ages of 907 ± 12 and 916 ± 11 Ma for the high-grade metamorphism, which is considerably younger than previously thought.Our results stress the hitherto underestimated importance of the late Sveconorwegian high-grade metamorphism in the southwestern part of the Baltic Shield.

Notes: Dark hornblende + garnet-rich, quartz-absent metagabbro boudins from the Seguin subdomain, Ontario Grenville Province, are transected by anastomosing light-coloured veins rich in orthopyroxene, clinopyroxene, plagioclase and sometimes quartz. The veins vary in texture from fine-grained diffuse veins and patches that overprint the metagabbro, to coarse tonalitic leucosomes with sharp borders. The diffuse veins and patches are suggestive of channellized subsolidus dehydration of the metagabbro, while the tonalitic leucosomes are suggestive of local internally-derived anatexis. All vein types grade smoothly into each other, with the tonalitic leucosomes being the latest.Relative to the host metagabbro, the veins have higher Si, Na, Ba & Sr, lower Fe, Mg, Ca & Ti, and similar Al. The coarser veins are enriched in K. Plagioclase becomes steadily enriched in Na in the transition from host metagabbro (An47) to the veins (An35), and in the coarsest veins it is antiperthitic. Differences in composition of the other minerals between host metagabbro and vein are minor. Pressure–temperature estimates are scattered, but indicate a minimum temperature during vein formation of 700°C at about 8 kbar.Mass balance constraints indicate that the veins formed from the metagabbro in an open system. The transecting veins are interpreted to represent pathways of Si + Na + Ba + Sr ± K ± Al-enriched, low aH2O fluids that metasomatized the host metagabbro to form the anhydrous veins. An initial period of localized solid-state dehydration of the metagabbro, represented by the diffuse veins, was followed by a transition to localized anatexis, represented by the tonalitic leucosomes. The change to anatexis may have been due to the addition of K to the infiltrating fluid. The source and delivery mechanism of the fluids is unknown.

Notes: Eclogite facies mineral assemblages are variably preserved in mafic and ultramafic rocks within the Western Gneiss Region (WGR) of Norway. Mineralogical and microstructural data indicate that some Mg–Cr-rich, Alpine-type peridotites have had a complex metamorphic history. The metamorphic evolution of these rocks has been described in terms of a seven-stage evolutionary model; each stage is characterized by a specific mineral assemblage. Stages II and III both comprise garnet-bearing mineral assemblages. Garnet-bearing assemblages are also present in Fe–Ti-rich peridotites which commonly occur as layers in mafic complexes. Sm–Nd isotopic results are reported for mineral and whole rock samples from both of these types of peridotites and related rocks.The partitioning of Sm and Nd between coexisting garnet and clinopyroxene is used to assess chemical equilibrium. One sample of Mg–Cr-type peridotite shows non-disturbed partitioning of Sm and Nd between Stage II garnet and clinopyroxene pairs and yields a garnet–clinopyroxene–whole-rock date of 1703 ± 29 Ma (I= 0.51069, MSWD = 0.04). This is the best estimate for the age of the Stage II high-P assemblage. Other Stage II garnet–clinopyroxene pairs reflect later disturbance of the Sm–Nd system and yield dates in the range 1303 to 1040 Ma. These dates may not have any geological significance. Stage III garnet–clinopyroxene pairs typically have equilibrated Sm–Nd partitioning and two samples yield dates of 437 ± 58 and 511 ± 18 Ma. This suggests that equilibration of the Stage III high-P assemblage is related to the Caledonian orogeny and is more or less contemporaneous with high-P metamorphism of ‘country-rock’eclogites in the surrounding gneisses. The Sm–Nd mineral data for the Fe–Ti-rich garnet peridotites and for a superferrian eclogite, which occurs as a dyke within the Gurskebotn Mg–Cr-type peridotite, are consistent with a Palaeozoic high-P metamorphism.Finally a synoptic P–T–t path is proposed for the Mg–Cr-type peridotites which is consistent with the petrological and geochronological data.

Notes: Compositional zoning in biotite–garnet pairs in metamorphic rocks from eastern Finland has been studied. The Mg profiles in the garnet side of biotite–garnet crystal pairs have been interpreted by means of Lasaga's theory (geospeedometry). However, the binary interdiffusion equations are first reformulated by starting from a ternary system and using the lattice fixed frame of reference. This frame of reference gives the fluxes directly by means of the numbers of diffusing ions, which helps to check the 1-dimensionality of the analysis assumed in Lasaga's theory. It is also shown that the recently argued effect of the third cation Ca is negligible in our samples. We were able to investigate satisfactory profiles in three samples from different areas. The values for the cooling rate are a few degrees per million years if the diffusion data obtained by Freer are adopted. The cooling rates are in agreement with recent estimates based on the K–Ar ages on biotite in the same areas.

Notes: In the Caledonide orogen of northern Sweden, the Seve Nappe Complex is dominated by rift facies sedimentary and mafic rocks derived from the Late Proterozoic Baltoscandian miogeocline and offshore-continent–Iapetus transition. Metamorphic breaks and structural inversions characterize the nappe complex. Within the Sarek Mountains, the Sarektjåkkå Nappe is composed of c. 600-Ma-old dolerites with subordinate screens of sedimentary rocks. These lithological elements preserve parageneses which record contact metamorphism at shallow crustal levels. The Sarektjåkkå Nappe is situated between eclogite-bearing nappes (Mikka and Tsäkkok nappes) which underwent high-P metamorphism at c. 500 Ma during westward subduction of the Baltoscandian margin. 40Ar/39Ar mineral ages of c. 520–500 Ma are recorded by hornblende within variably foliated amphibolite derived from mafic dyke protoliths within the Sarektjåkkå Nappe. Plateau ages of 500 Ma are displayed by muscovite within the basal thrust of the nappe and are consistent with metamorphic evidence which indicates that the nappe escaped crustal depression as a result of detachment at an early stage of subduction. Cooling ages recorded by hornblende from variably retrogressed eclogites in the entire region are in the range of c. 510–490 Ma and suggest that imbrication of the subducting miogeocline was followed by differential exhumation of the various imbricate sheets. Hornblende cooling ages of 470–460 Ma are recorded from massive dyke protoliths within the Sarektjåkkå Nappe. These are similar to ages reported from the Seve Nappe Complex in the central Scandinavian Caledonides. Probably these date imbrication and uplift related to Early Ordovician arrival of outboard terranes (e.g. island-arc sequences represented by structurally lower horizons of the Köli Nappes).Metamorphic contrasts and the distinct grouping of mineral cooling ages suggest that the various Seve structural units are themselves internally imbricated, and were individually tectonically uplifted through argon closure temperatures during assembly of the Seve Nappe Complex. The cooling ages of 520–500 Ma recorded within Seve terranes and along terrane boundaries of the Sarek Mountains provide evidence of significant accretionary activity in the northern Scandinavian Caledonides in the Late Cambrian–Early Ordovician.

Notes: Around Fiskefjord, southern West Greenland, Archaean amphibolite-facies, granulite-facies and retrograde orthogneisses occur in lithological and structural continuity with each other. The granulite-facies rocks here—and elsewhere in West Greenland—are surrounded by extensive areas of retrograde gneisses. Both the prograde and retrograde metamorphism took place in a major event of continental crust formation c. 3000 Ma ago, which gave rise to granulite-facies conditions in part of the rock complex exposed today. In the Fiskefjord area distributions of major and trace elements, as well as strontium and lead isotopes, show that the fades transformations were accompanied by pronounced metasomatism, and mineral chemistry indicates that the hydrous retrograde metamorphism took place under amphibolite-facies conditions and was gradual and incomplete. The metamorphic and metasomatic processes in the Fiskefjord area are believed to have been controlled by heat from continuous intracrustal injection of large masses of tonalitic magma, which caused gradual dehydration and partial melting, followed by liberation of aqueous fluids during crystallization of anatectic melts. These fluids partially retrograded previously dehydrated gneisses. In contrast, South Indian high-grade gneisses have mainly prograde amphibolite–granulite-facies transitions which are distinct and well preserved, later than penetrative deformation, and are likely to have been controlled by CO2 streaming. These amphibolite–granulite-facies transitions are reported to be near-isochemical. It is suggested that there are (at least) two different kinds of granulite-facies metamorphism: a near-isochemical prograde type in stabilized tectonic environments, perhaps controlled by influx of CO2 (e.g. in South India) and significantly post-dating original crust formation; and a fluid-deficient type with widespread anatexis, hydrous retrogression and metasomatism, which takes place during accretion of continental crust, and in which heat is the governing factor (e.g. in southern West Greenland).

Notes: Garnet lherzolite from the Lyonnais area (eastern French Massif Central) occurs as several lenses elongated within the regional foliation of garnet-biotite-sillimanite gneisses. Within the peridotites a mylonitic foliation can be observed which clearly is oblique to the regional foliation of the surrounding gneisses. Petrological and thermobarometric studies emphasize a tectonometamorphic re-equilibration for both crustal and mantle rocks characterized by a prograde metamorphic stage followed by retrograde evolution. During the burial stage, interpreted as lithospheric subduction, the peridotites underwent their mylonitic deformation, under high-pressure conditions (23–30 kbar). In contrast, the paragneisses have suffered their deformation during the retromorphic evolution under mesozonal conditions (6–8 kbar, 700°C). Our thermobarometric investigations allow us to interpret the granulitic/ultramafic association from the Monts du Lyonnais area as a lithospheric section buried into a Palaeozoic subduction zone, laminated during continental collision and uplifted by erosion processes.

Notes: Manganese-rich and manganese-poor iron formations which occur as thin layers in the Halaguru-Satnuru area, south of Kabbaldurga, Karnataka, India are chemically intermediate between the ‘Algoma’and ‘Lake Superior’types, but higher in their MnO and TiO2 contents. The rocks are of four petrographic varieties: (a) quartz-magnetite-orthopyroxene-clinopyroxene, (b) quartz-magnetite-orthopyroxene-clinopyroxene-garnet, (c) quartz-magnetite-clinopyroxene-garnet, and (d) quartz-magnetite-clinopyroxene-garnet-plagioclase.In the orthopyroxene-clinopyroxene pairs, Mn-Mg and Mn-Fe exchange is ideal irrespective of the MnSiO3 contents of orthopyroxenes (0.6–1.8 mol. % in Mn-poor and 15–25 mol. % in Mn-rich compositions). Mg-Fe exchange in the same pair is however non-ideal. Mn-Fe exchange in orthopyroxene-garnet pairs is ideal. The distribution patterns in the other binaries are inconclusive regarding ideality of exchange. Orthopyroxene-garnet and clinopyroxene-garnet geothermometers, modified for high spessartine contents, give temperatures of 800 ± 30° C. A modified version of the Harley (1984) geothermometer registers 740 ± 60° C, in agreement with the consensus temperature value.The equilibrium log ffo2 values in the iron formations, as calculated from the reaction 6FeSiO3+ O2= 2Fe3O4+ 6SiO2 are in the range of −14.2 to −15.5. Algebraic analysis of variations of fo2 with composition of phases indicates buffering of O2 in the rocks. The absence of grunerite in these assemblages is compatible with XH2O being less than 0.3 in the ambient fluid. Computations from volatile equilibria in the C-O-H system, however, predict high XH2O values (〉0.7) at ac= 1.0, implying that the activity of graphite must have been greatly reduced—this is in accordance with the absence of graphite in these rocks.

Notes: This paper describes the deformation and metamorphism recorded in the Zoovoorby staurolite schist, a sliver of pelitic supracrustal material in the 1.3–1.0 Ga eastern Namaqua Province, South Africa. The supracrustal Biesjepoort Group, of which the schist is a part, has undergone at least four phases of deformation (D1–D4). D1 and D2 are preserved in the pelitic schists; staurolite and garnet grew during D1, with staurolite growth persisting to the very earliest D2 crenulation. Andalusite, found in more Mg-rich schists, grew during D2, overprinting both S1 schistosity and S0 banding. S2 has been rotated both with respect to S1 (preserved as parallel orientated inclusion trails in garnet and staurolite) and with respect to its original orientation (preserved as open D2 crenulations in staurolite). Staurolite is dissolved against S2 in zones of progressive shear. The pseudomorphing of staurolite and andalusite by cordierite, and the preservation of relic grains of both minerals in a wide range of garnet–cordierite pelites throughout the eastern Namaqua Province infers that what is preserved fortuitously in the Zoovoorby locality is representative of the early metamorphic history of a much larger terrane. The high thermal gradients needed to attain estimated conditions of 540–550° C and 1.6–2.4 kbar require substantial heat input. Large amounts of foliated (syn-D2) granite amongst the supracrustal succession are inferred to be the result of delamination of a thickened crust at a destructive plate margin, generating an elevated thermal gradient during D1–D2 times.

Notes: Poikiloblastic index minerals in pelitic rocks from the Orrs Island–Harpswell Neck area of coastal Maine contain inclusion textures that indicate sequential growth of progressively higher grade metamorphic minerals during development of a near-vertical crenulation foliation. The sequence of zones in the field is garnet, staurolite, staurolite–andalusite, staurolite–sillimanite and sillimanite. Inclusion fabrics characteristic of different stages in crenulation cleavage development indicate that index minerals nucleated and grew sequentially: biotite began to grow before deformation, garnet began to grow during early stages of crenulation cleavage development, staurolite grew during intermediate stages, and andalusite grew relatively late, when transposition of the foliation was nearly complete. Muscovite pseudomorphs and sillimanite were mainly post-kinematic. The fact that metamorphic index minerals grew sequentially in individual rocks in the same order in which they appear across the field area indicates that the high temperature part of the pressure–temperature path was similar to the metamorphic field gradient.Metamorphism in the Orrs Island–Harpswell Neck area is consistent with the magmatic heating model that has been proposed for western Maine. Sequential development of index minerals in pelitic rocks in the Orrs Island–Harpswell Neck area apparently resulted from sequential nucleation after substantial overstepping of mineral-forming reactions. Once nucleation of an index mineral had taken place, initial growth was rapid and poikiloblasts preserved inclusion trails characteristic of the prevailing stage of crenulation cleavage development. Because nucleation of sillimanite may have required more overstepping of the andalusite–sillimanite reaction than nucleation at dehydration reactions, determination of metamorphic conditions for rapidly heated rocks such as these by comparison with a petrogenetic grid is problematic. Garnet zoning patterns in these rocks should reflect the fact that growth of garnet interiors occurred early during metamorphism in equilibrium with a low-grade assemblage. Only garnet rims would be expected to record the subsequent pressure–temperature path.

Notes: The Nordlandet peninsula (Akia terrane) and the Tasiusarsuaq terrane in southern West Greenland were metamorphosed to granulite facies at 3.0 and 2.8 Ga respectively. Temperatures of metamorphism are estimated using magnetite + ilmenite, garnet + orthopyroxene, garnet + clinopyroxene and garnet + biotite thermometers. Barometry has been carried out in the two terranes using eight different garnet barometers. A uniform set of activity models for all minerals, including the garnet activity model of Newton et al. (1986), is applied to each barometer in order to permit comparison. Pressure estimates using the different barometers are generally quite consistent (±1.5 kbar). Use of the Newton et al. (1986) garnet activity data results in pressures similar to those obtained using other garnet activity models.Peak metamorphic conditions on the Nordlandet peninsula are estimated to have been 800 ± 50°C, 7.9 ± 1.0 kbar. Values of logfO2 are estimated to have been 1.1 to 2.0 above the quartz + magnetite + fayalite buffer from assemblages of magnetite + ilmenite and quartz + magnetite + ferrosilite. Peak metamorphic conditions in the Tasiusarsuaq terrane are estimated to have been 780 ± 50°C, 8.9 ± 1.0 kbar. Estimates of fH2O and fCO2 using biotite, amphibile, grossular + anorthite and grossular + scapolite equilibria are low in both terranes. These results suggest that granulite metamorphism was fluid absent in both terranes, and that the metamorphism in the Akia terrane and possibly also in the Tasiusarsuaq terrane was initiated by the injection of large volumes of magma into the lower crust.

Notes: Abstract Aegirine–jadeite clinopyroxene (〉60 mol% jadeite) locally occurs within blueschists of the ‘Lower Allochthon’exposed in the Trás-os-Montes region of northern Portugal. Peak conditions attained during blueschist facies metamorphism are estimated to have been c. 420° C and 〉11 kbar. Porphyroblastic white mica (paragonite/phengite) within the blueschist assemblage records a 36Ar/40Ar versus 39Ar/40Ar isotope correlation age of 329.4 ± 1.6 Ma. In view of the relatively low-T nature of the metamorphism, the c. 330-Ma age is interpreted to date closely the high-P recrystallization. This tectonothermal activity is interpreted to have resulted from structural emplacement of a previously assembled crystalline nappe complex (‘Upper Allochthon/Ophiolite Nappe’) onto Iberian protoliths of the Lower Allochthon during terminal stages of the Hercynian orogeny.

Notes: Abstract Standard petrographic, microthermometric and Raman spectroscopic analyses of fluid inclusions from the metamorphosed massive sulphide deposits at Ducktown, Tennessee, indicate that fluids with a wide range of compositions in the C–O–H–N–S–salt system were involved in the syn- to post-metamorphic history of these deposits. Primary fluid inclusions from peak metamorphic clinopyroxene contain low-salinity, H2O–CH4 fluids and calcite, quartz and pyrrhotite daughter crystals. Many of these inclusions exhibit morphologies resembling those produced in laboratory experiments in which confining pressures significantly exceed the internal pressures of the inclusions. Secondary inclusions in metamorphic quartz from veins, pods, and host matrix record a complex uplift history involving a variety of fluids in the C–O–H–N–salt system. Early fluids were generated by local devolatilization reactions while later fluids were derived externally.Isochores calculated for secondary inclusions in addition to the chronology of trapping and morphological features of primary and secondary fluid inclusions suggest an uplift path which was concave toward the temperature axis over the P–T range 6–3 kbar and 550–225° C. Immiscible H2O–CH4–N2–NaCl fluids were trapped under lithostatic to hydrostatic pressure conditions at 3–0.5 kbar and 215 ± 20° C. Entrapment occurred during Alleghanian thrusting, and the fluids may have been derived by tectonically driven expulsion of pore fluids and thermal maturation of organic material in lower-plate sedimentary rocks which are thought to underlie the deposits. Episodic fracturing and concomitant pressure decreases in upper-plate rocks, which host the ore bodies, would have allowed these fluids to move upward and become immiscible. Post-Alleghanian uplift appears to have been temperature-convex.Uplift rates of 0.10–0.05 mm year−1 from middle Ordovician to middle Silurian – late Devonian, and 0.07–0.12 mm year−1 from middle Silurian – late Devonian to late Permian are suggested by our uplift path and available geochronological data.

Notes: Abstract Metapelites in the Altavista area, southwest Virginia Piedmont, USA, underwent allochemical hydrothermal retrograde metamorphism in synmetamorphic shear zones. The metapelites of the Evington Group were metamorphosed in a prograde sequence of chlorite, staurolite, and sillimanite zones. Garnet–biotite geothermometry and phase relations support eastward increasing metamorphic grade, ranging from 570° C in the staurolite zone to 650° C in the sillimanite zone at c. 5.8 kbar. Sillimanite-zone rocks later underwent progressive retrogression around shear zones which acted as fluid conduits. Retrograde assemblages are successively zoned around the shear zones with staurolite-, chloritoid- and kyanite-bearing assemblages. The shear zones commonly contain kyanite or tourmaline veins. Applicable phase equilibria indicate that retrogression occurred during isobaric cooling through c. 200–270° C. Rock compositional changes with retrogression occurred in steps: SiO2 was gained in the early stages of the retrogression but lost in the late stages; Al2O3, K2O, and H2O were increasingly gained through the sequence; CaO was increasingly lost. Addition of H2O and decreasing temperatures resulted in new ferromagnesian minerals (staurolite, chloritoid, chlorite) and changes in H2O, SiO2, Al2O3, K2O, and CaO contents produced muscovite and sodic plagioclase.Subsequent to prograde metamorphism, deeply derived fluids migrated upwards along shear zones, providing fluid and energy for the retrograde reactions. The sheared rocks underwent fluid infiltration with fluid fluxes of 1.8 × 107–4.3 × 107 cm3/cm2 corresponding to minimum estimated fluid-to-rock ratios of 7.5–21 as a function of position within the shear zone. Fluid flow was from high to low temperature early and low to high temperature later in the retrogression.

Notes: Garnet-biotite gneisses, some of which contain sillimanite or hornblende, are widespread within the Otter Lake terrain, a portion of the Grenville Province of the Canadian Shield. The metamorphic grade is upper amphibolite to, locally, lower granulite facies.The atomic ratio Fe2+/(Fe2++ Fe3+) in biotite ranges from 0.79 to 0.89 (ferrous iron determinations in 10 highly pure separates), with a mean of 0.86. Mg and Fe2+ atoms occupy 67–78% of the octahedral sites, the remainder are occupied by Fe3+, Ti, and Al, and some are vacant. Mg/(Mg + Fe2+), denoted X, in the analysed samples ranges from 0.32 to 0.65. Garnet contains 1–24% grossular, 1–12% spessartine and X ranges from 0.07 to 0.34.Compositional variation in biotite and garnet is examined in relation to three mineral equilibria:(I) biotite + sillimanite + quartz = garnet + K-feldspar + H2O;(II) pyrope + annite = almandine + phlogopite;(III) anorthite = grossular + sillimanite + quartz.Measurements of X (biotite) and X (garnet) are used to construct an illustrative model for equilibrium (I) which relates the observed variation in X to a temperature range of 70°C or a range in H2O activity of 0.6; the latter interpretation is preferred.In sillimanite-free gneisses, the distribution of Mg and Fe2+ between garnet (low in Ca and Mn) and biotite is adequately described by a distribution coefficient (KD) of 4.1 (equilibrium II). The observed increase in the distribution coefficient with increasing Ca in garnet is ln KD= 1.3 + 2.5 × 10−2 [Ca]where [Ca] = 100 Ca/(Mg + Fe2++ Mn + Ca). The distribution coefficient is apparently unaffected by the presence of up to 12% spessartine in garnet.In several specimens of garnet-sillimanite-plagioclase gneiss, the Ca contents of garnet and of plagioclase increase in unison, as required by equilibrium (III). The mean pressure calculated from these data (n= 17) is 5.9 kbar, and the 95% confidence limits are ±0.5 kbar.

Notes: Pumpellyite from four-phase assemblages (pumpellyite + epidote + prehnite + chlorite; pumpellyite + epidote + actinolite + chlorite; pumpellyite + epidote + Na-amphibole + chlorite, together with common excess phases), considered to be low variance in a CaO-(MgO + FeO)-Al2O3-Fe2O3 (+Na2O + SiO2+ H2O) system, have been examined in areas which underwent metamorphism in the prehnite-pumpellyite, pumpellyite-actinolite and low-temperature blueschist facies respectively. The analysed mineral assemblages are compared for nearly constant (basaltic) chemical composition at varying metamorphic grade and for varying chemical composition (basic, intermediate, acidic) at constant metamorphic conditions (low-temperature blueschist facies).In the studied mineral assemblages, coexisting phases approached near chemical equilibrium. At constant (basaltic) bulk rock composition the MgO content of pumpellyite increases, and the XFe3+ of both pumpellyite and epidote decreases with increasing metamorphic grade, the Fe3+ being preferentially concentrated in epidote. Both pumpellyite and epidote compositions vary with the bulk rock composition at isofacial conditions; pumpellyite becomes progressively enriched in Fe and depleted in Mg from basic to intermediate and acidic bulk rock compositions. The compositional comparison of pumpellyites from high-variance (1–3 phases) assemblages in various bulk rock compositions (basic, intermediate, acidic rocks, greywackes, gabbros) shows that the compositional fields of both pumpellyite and epidote are wide and variable, broadly overlapping the compositional effects observed at varying metamorphic grade in low-variance assemblages.The intrinsic stability of both Fe- and Al-rich pumpellyites extends across the complete range of the considered metamorphic conditions. Element partitioning between coexisting phases is the main control on the mineral composition at different P-T conditions.

Notes: The Southern Brittany Migmatite Belt (SBMB), which evolved through the metamorphic peak between c. 400 Ma and c.. 370 Ma ago, consists of a heterogeneous suite of high-grade gneisses and anatectic migmatites, both metatexites and diatexites. Rare garnet-cordierite gneiss layers record evidence of an early prograde P-T path. In these rocks, growth-zoned garnet cores and a sequence of included mineral assemblages in garnet, from core to rim, of Qtz + Ilm + Ky, Pl + Ky + St + Rt + Bt and Pl + Sil + St + Rt + Bt constrain a prograde evolution during which the reactions Ilm + Ky + Qtz→ Aim + Rt, Ms + Chl→ St + Bt + Qtz + V and St + Qtz→ Grt + Sil + V were crossed. Parts of this prograde evolution are preserved as inclusion assemblages in garnet in all other rock types. In all rock types, garnet has reverse zoned rims, and garnet replacement by cordierite and/or biotite and plagioclase suggests the following reactions have occurred: Grt + Sil + Qtz→ Crd → Hc ± Ilm, Bt + Sil + Qtz → Crd ± Hc → Ilm → Kfs + V and (Na + Ca + K + Ti) + Grt → Bt + Pl + Qtz. Microstructural analysis of reaction textures in conjunction with a petrogenetic grid has enabled the construction of a tightly constrained ‘clockwise’P–T path for the SBMB. The high-temperature part of the path has a steep dT/dP slope characteristic of near isothermal decompression. It is proposed that the P-T path followed by the SBMB is the result of the inversion, by overthrusting, of a back-arc basin and that such a tectonic setting may be applicable to other high-temperature migmatite terranes. The near isothermal decompression is at least partly driven by the upward (diapiric) movement of the diatexite/anatectic granite core of the SBMB.

Notes: By collating age data based on the fossil age of the protoliths, radiometric dating of the metamorphic minerals, and sedimentary records of erosion at the earth's surface, the history of the Sanbagawa metamorphism can be summarized as follows. (1) The pre-metamorphic sedimentary rocks (Carboniferous-Jurassic + Early Cretaceous?) became mixed and formed a thickened packet in the vicinity of an ancient trench through a variety of subduction-related tectono-sedimentary processes, probably in Early Cretaceous time (c., 130-120 Ma). (2) The subducted protoliths underwent progressive metamorphism reaching a maximum depth of c. 30 km in late Early Cretaceous time (c. 116 ± 10 Ma). (3) The high-P/T metamorphic rocks began to rise toward the surface (during the interval 110-50 Ma) with minimum estimates for the average cooling rate around 9-12°C/Ma and an average uplift rate around 0.4-0.5 mm/year. (4) Finally, at some stage after reaching the erosional surface, the high-P/T metamorphic rocks were covered unconformably by the middle Eocene (c. 50-42 Ma) Kuma Group.On the basis of the present chronological summary of the Sanbagawa metamorphism, the areal extent of the Sanbagawa metamorphism is also discussed with respect to the weakly metamorphosed subduction-accretion complex of the next tectonic belt to the south, the Northern Chichibu belt.

Notes: The mineral assemblages of hematite-bearing basic schists in intermediate high-pressure metamorphism are temperature dependent. For assemblages with excess hematite, albite, muscovite and quartz, the paragenetic relations can be dealt with in terms of a four-component system, without omitting or grouping major components.In the Sanbagawa belt in central Shikoku, the dominant amphibole in the hematite-bearing basic schists changes from winchite, via crossite and barroisite to hornblende. The stability of amphibole is described chemographically within a pseudoternary system with another excess phase, epidote. Many amphiboles are chemically heterogeneous owing to retrograde reactions which produced low-T/P amphibole around the prograde amphibole. The examination of amphibole zoning makes it possible to draw a retrograde P-T trajectory which passes on the lower pressure side of the prograde one.

Notes: The dominant deformation mechanism during the Sambagawa metamorphism changes from brittle to ductile with increasing metamorphic temperature. The magnitude of plastic strains inferred from the shapes of deformed radiolaria in metachert increases sharply across the boundary between the epidote-pumpellyite-actinolite zone and the epidote-actinolite zone. The synmetamorphic crack density of metachert is an indicator of the contemporaneous brittle strain of rocks, and it decreases sharply as the grade reaches the epidote-actinolite zone. Hence, the ratio of the ductile strain to the brittle strain of metachert decreases rapidly across the transition to the epidote-actinolite zone of the Sambagawa metamorphic belt.The sharp change of the ductile strain magnitude also takes place at the epidote-actinolite grade in the Shimanto metamorphic belt of Japan, an example of the intermediate pressure facies series of metamorphism. It is concluded that the transition from brittle to ductile deformation takes place at about 300-400°C. and is independent of pressure of metamorphism.

Notes: Metamorphic mineral assemblages and textures from Early Palaeozoic continental margin rocks in north-western Newfoundland indicate that different structural levels have contrasting metamorphic histories. Rocks of the East Pond Metamorphic Suite, which represent the older, structurally lower level of the margin, experienced an early high-pressure–low-temperature stage of metamorphism (10–12 kbar minimum, 450–500°C) which produced eclogite in mafic dykes and phengite–garnet assemblages in pelites. This was overprinted by higher temperature–lower pressure amphibolite facies metamorphism (700–750°C, 7–9 kbar minimum) which produced complex symplectic textures in rocks of all compositions. Rocks of the Fleur de Lys Supergroup, which were deposited in the stratigraphically higher levels of the rifted margin, reached pressures of 7–8.5 kbar at about 450°C during the early stages of metamorphism, overprinted by assemblages which indicate maximum temperatures of 550–600°C at about 6.5 kbar. The metamorphic history of both units is interpreted to be the result of thermal relaxation following initial burial of a continental margin by overriding thrust sheets. Since there is no evidence that maximum pressures or temperatures within the Fleur de Lys Supergroup were ever as high as those reached in the East Pond Metamorphic Suite, these rocks may have followed parallel, ‘nested’P–T–t paths, with the more deeply buried East Pond Metamorphic Suite subjected to greater thermal relaxation effects. Quantitative modelling of P–T–t paths is not possible with the present data, owing to both large uncertainties in P–T estimates, and in the time of metamorphism.

Notes: Eclogites in the Tromsø area, northern Norway, are intimately associated with meta-supracrustals within the Uppermost Allochthon of the Scandinavian Caledonides (the Tromsø Nappe Complex). The whole sequence, which includes pelitic to semipelitic schists and gneisses, marbles and calc-silicate rocks, quartzofeldspathic gneisses, metabasites and ultramafites, has undergone three main deformational/metamorphic events (D1/M1, D2/M2 and D3/M3). Detailed structural, microtextural and mineral chemical studies have made it possible to construct separate P–T paths for these three events.Chemically zoned late syn- to post-D1 garnets with inclusions of Bt, Pl and Qtz in Ky-bearing metapelites indicate a prograde evolution from 636°C, 12.48 kbar to c. 720°C, 14–15 kbar. This latter result is in agreement with Grt–Cpx geothermometry and Grt–Cpx–Pl–Qtz geobarometry on eclogites and trondhjemitic to dioritic gneisses. Maximum pressures at c. 675°C probably reached 17–18 kbar based on Cpx–Pl–Qtz inclusions in eclogitic garnets, and Grt–Ky–Pl–Qtz and Jd–Ab–Qtz in trondhjemitic gneisses. Post-D1/pre-D2 decompressional breakdown of the high-P assemblages indicates a substantial drop in pressure at this stage. Inclusions and chemical zoning in syn- to post-D2 garnets from metapelites record a second episode of prograde metamorphism, from 552°C, 7.95 kbar, passing through a maximum pressure of 10.64 kbar at 644°C, with final equilibration at c. 665°C, 9–10 kbar. The corresponding apparently co-facial paragenesis Grt + Cpx + Pl + Qtz in metabasites yields c. 635°C, 8–10 kbar. In the metapelites post-D3, Grt in apparent equilibrium with Bt, Phe and Pl yield c. 630°C, 9 kbar. The D1/M1 and D2/M2 episodes are exclusively recorded in the Tromsø Nappe Complex and must thus pre-date the emplacement of this allochthonous unit on top of the underlying Lyngen Nappe, while the D3/M3 episode is common for the two units.A previously published Sm–Nd mineral isochron (Grt–Cpx–Am) on a partly retrograded and recrystallized ecologite of 598 ± 107 Ma represents either the timing of formation of the eclogites or the post-eclogite/pre-D2 decompression stage, while a Rb–Sr whole rock isochron of an apparently post-D1/pre-D2 granite of 433 ± 11 Ma is consistent with a K–Ar age of post-D1/pre-D2 amphiboles from a retrograded eclogite of 437 ± 16 Ma which most likely record cooling below the 475–500°C isotherm after the M3 metamorphism.

Notes: Abstract Mafic phyllosilicates in metabasites affected by low-grade regional metamorphism from Wales and eastern North Greenland show variations in their structure and chemistry. These variations are related to four mineral zones in these metabasites, which are recognized on the presence/absence of various key calc-silicate minerals and also actinolite. Zones 1 and 2 equate with the zeolite facies, zone 3 with the prehnite–pumpellyite facies (or prehnite–actinolite facies in rocks with appropriate bulk rock composition) and zone 4 with the greenschist facies. Whilst variations in Fe/(Fe + Mg) in chlorite correlate closely with Fe/(Fe + Mg) ratios in the whole-rock, other chemical variations are clearly unrelated to whole-rock compositions. Contents of Aliv are seen to increase systematically in samples from zone 1 through to zone 4, which relate to an increase in temperature. Calibration of alteration temperatures, calculated using the chlorite geothermometer (based on Aliv contents) developed for meta-andesites in the Los Azufres geothermal system (Mexico), against x values (an estimate of the proportion of chlorite to swelling component in the mafic phyllosilicates) shows a decrease in the swelling component in passing from zone 1 to zone 4, i.e. with an increase in temperature. Calculated temperatures compare favourably with published stability estimates for the various key calc-silicates and actinolite. These data indicate that the chlorite geothermometer, although developed for meta-andesites from a hydrothermal system, does show a correlation with temperatures estimated from calc-silicate assemblages in metabasites affected by low-grade metamorphism developed on a regional scale.

Notes: Abstract Regional metamorphism in the external Variscides of southwest England varied from diagenetic level to greenschist facies. There is a fundamental difference in the metamorphic character between the northern and southern regions of the area. In the north, M1 metamorphism is of a sedimentary burial character associated with high heat flow, whilst to the south it is related to tectonic burial during thrust thickening processes, with lower geothermal gradients. This pattern appears to be related to the character of basin development and its subsequent tectonic evolution. The northern region has features that accord with a diastathermal (extensional) origin for the very low-grade metamorphism whilst in the southern region the very low-grade metamorphism is linked to thrusting as a consequence of Variscan compression. The Tintagel High-Strain Zone presents an anomaly in this regional pattern where an M2 metamorphic phase is attributed to localized D2 thrust stacking along the southern margin of the Culm Basin.There is no extensive overprint of the regional metamorphic pattern by the contact aureoles surrounding the granite plutons of the region. However, there is a noticeable coincidence between the areas of regional epizone grade and the extent of the geophysically defined subsurface limit of the granite batholith (excluding the North Devon area). This link is attributed largely to the late-stage structural up-doming of the higher grade areas over the roof of the batholith.

Notes: High Temperature Metamorphism and Crustal Anatexis. Edited by J. R. Ashworth & M. Brown. The Mineralogical Society Series The Al2SiO5 Polymorphs. By Derrill M. Kerrick. Reviews in Mineralogy

Notes: Abstract Evaluation of two commonly used microstructural criteria for determining the origin of inclusions, namely the existence of a host–inclusion orientation relationship and continuity between inclusions and matrix, using two specific examples of inclusions of tschermakite in actinolitic hornblende, shows that these criteria can be difficult to implement and if not applied carefully will give contradictory results. Consequently, it may be difficult to establish the origins of inclusions; petrographic studies should therefore clearly state the criteria used for interpretation of host–inclusion relationships and how these criteria were implemented.

Notes: Abstract Syn-metamorphic re-imbrication of the internal part of thrust belts can result in distinct pressure–temperature–time–deformation (P–T–t–d) pathways for different structural–metamorphic domains. In the early Proterozoic Cape Smith Thrust Belt (Canada), an external (piggyback-sequence thrusting) domain is characterized by thermal peak metamorphism occurring after deformation. In contrast, thermal peak metamorphism in an internal domain occurred during re-imbrication by out-of-sequence thrusting. The interactions of tectonic and thermal processes have been studied using three methods: (i) qualitative evaluation of the timing between mineral growth and deformation; (ii) analytical P–T paths from growth-zoned garnet porphyroblasts; and (iii) numerical modelling of vertical heat conduction. Derived P–T–t–d pathways suggest that uplift in the external domain resulted in part from erosion and isostatic unloading. In contrast, paths for the internal domain indicate that the out-of-sequence portion of the thrust belt may have experienced faster unroofing relative to the external domain. This is attributed to thickening by out-of-sequence thrusting and possibly to extensional faulting at (now eroded) higher structural levels. Observations on the timing of metamorphism, coupled with numerical modelling, suggest that the thermal peak metamorphism documented in the external domain is a consequence of the emplacement of the out-of-sequence thrusts stack in the internal portion of the thrust belt.

Notes: Abstract CO2-bearing fluid inclusions in strongly lineated but weakly foliated late Precambrian gneisses within the Hope Valley Shear zone of Connecticut and Rhode Island are of mixed composition (Xco2± 0.1; 7 wt% NaCl equivalent) and variable density (0.59–0.86 g/ml) and occur mainly as isolated inclusions. Also present are dilute (3 wt% NaCl equivalent) aqueous inclusions which occur on healed fractures related to greenschist facies retrograde metamorphism. Isochores for dense isolated CO2-bearing inclusions indicate pressures of 7.5–9 kbar at 500–600° C, the estimated temperature conditions of peak metamorphism. Published 40Ar/39Ar hornblende plateau age spectra indicate cooling through about 500° C at 265 ± 5 Ma. Isochores for low-density CO2-bearing inclusions and aqueous inclusions intersect at the conditions of retrograde metamorphism (325–400° C) and indicate pressures of 3–4 kbar. Published 40Ar/39Ar biotite plateau ages indicate cooling through about 300° C at 250 ± 5 Ma. These data define a P–T uplift curve for the region which is convex towards the temperature axis and indicate uplift rates between 0.4 and 3.3 mm/year in Permian time. Exhumation of basement gneisses was coeval with normal (west-down) motion along the regional basement–cover contact (Honey Hill–Lake Char–Willimantic fault system), and is interpreted as due to post-orogenic extensional collapse of the Alleghanian orogeny.

Notes: Abstract The Proterozoic low-pressure, high-temperature (LPHT) terrane of the Reynolds Range occurs in a 130-km-long, NW-trending belt in the central part of the Arunta Block, central Australia. The Reynolds Range has been affected by two mid-Proterozoic tectonic cycles, DI and DII, associated with two metamorphic events, MI and MII. DI–MI effects are restricted to the older of two sedimentary successions, the Lander Rock beds, which are separated from the younger Reynolds Range Group by an angular unconformity. The dominant structural–metamorphic features formed during DII–MII affected both sedimentary successions and the various granites that intruded them, and reworked most DI–MI effects. The DII deformation history can be subdivided into one prograde, two peak, and one retrograde stage. Average P–T calculations in the southeastern half of the range indicate a peak-metamorphic pressure of 4.1 ± 0.3 kbar. Because the calculated values are derived from the same stratigraphic level corresponding to the base of the Reynolds Range Group, which is exposed throughout the area, it is likely that pressures were similar in the entire range. In fact, however, the peak-metamorphic temperature shows a dramatic increase from greenschist facies (c. 400° C) in the northwest to granulite facies (740 ± 60° C) in the southeast, indicating that MII was associated with anomalously high heat flows. The P–T path is anticlockwise, with isobaric cooling from the metamorphic peak indicated by corona textures. However, the evidence of a prograde increase in pressure is indirect and based on the compressional nature of the structures. Peak-metamorphic mineral assemblages and retrograde mineral assemblages in amphibolite facies shear zones show the same metamorphic zonation, suggesting they formed in response to the same thermal event. If this is true, the implication is that a thermal perturbation external to the crust was maintained for a considerable period of time (110 Ma, based on zircon dating). As it is not clear whether Proterozoic, asthenosphere-active, thermal perturbations operated for this long, the alternative interpretation must be considered, namely that the peak-metamorphic events are separate from the shear zone event associated with reheating of the area.

Notes: Abstract Finite difference models of Fe-Mg diffusion in garnet undergoing cooling from metamorphic peak conditions are used to infer the significance of temperatures calculated using garnet-biotite Fe-Mg exchange thermometry. For rocks cooled from high grades where the garnet was initially homogeneous, the calculated temperature (Tcalc) using garnet core and matrix biotite depends on the size of the garnet, the ratio of garnet to biotite in the rock (Vgarnet/Vbiotite) and the cooling rate. For garnets with radii of 1 mm and Vgarnet/Vbiotite〈1, Tcalc is 633, 700 and 777°C for cooling rates of 1, 10 and 100°C/Ma. For Vgarnet/Vbiotite= 1 and 4 and a cooling rate of 10° C/Ma, Tcalc is approximately 660 and 610° C, respectively. Smaller and larger garnets have lower and higher Tcalc, respectively. These results suggest that peak metamorphic temperatures may be reliably attained from rocks crystallized at conditions below Tcalc of the garnet core, provided that Vgarnet/Vbiotite is sufficiently small (〈0.1) and that the composition of the biotite at the metamorphic peak has not been altered during cooling.Numerical experiments on amphibolite facies garnets with nominal peak temperatures of 550–600° C generate a ‘well’in Fe/(Fe + Mg) near the rim during cooling. Maximum calculated temperatures for the assemblage garnet + chlorite + biotite + muscovite + plagioclase + quartz using the Fe/(Fe + Mg) at the bottom of the ‘well’with matrix biotite range from 23–43° C to 5–12° C below the peak metamorphic temperature for cooling rates of 1 and 100° C/Ma, respectively. Maximum calculated temperatures for the assemblage garnet + staurolite + biotite + muscovite + plagioclase + quartz are approximately 70° C below the peak metamorphic temperature and are not strongly dependent on cooling rate. The results of this study indicate that it may be very difficult to calculate peak metamorphic temperatures using garnet-biotite Fe-Mg exchange thermometry on amphibolite facies rocks (Tmax 〉 550° C) because the rim composition of the garnet, which is required to calculate the peak temperature, is that most easily destroyed by diffusion.

Notes: The tectonic settings for the formation and evolution of regional granulite terranes and the lowermost continental crust can be deduced from pressure–temperature–time (P–T–time) paths and constrained by petrological and geophysical considerations. P–T conditions deduced for regional granulites require transient, average geothermal gradients of greater than 35°C km−1, implying minimum heat flow in excess of 100 mWm−2. Such high heat flow is probably caused by magmatic heating. Tectonic settings wherein such conditions are found include convergent plate margins, continental rifts, hot spots and at the margins of large, deep-seated batholiths. However, particular P–T–time paths do not allow specific tectonic settings to be distinguished at this time. Under different conditions, both clockwise, CW (Pmax attained before Tmax), and anticlockwise, ACW (Pmax attained slightly after Tmax), paths are possible in the same tectonic setting. Both CW and ACW end-member paths can yield nearly isobaric cooling, IBC, paths. Such cooling paths are clearly not an artefact of thermobarometry, but can be constrained by solid–solid and devolatilization equilibria and geophysical modelling.In terms of understanding the evolution of the deep crust, a potentially significant group of regional granulite terranes are those that show evidence for ACW-IBC paths. Such paths are the likely result of: (i) episodic igneous activity resulting in intrusions within all levels of the crust, (ii) thickening of the crust by magmatic underplating, (iii) slow uplift as a result of the formation of a deep, garnet-rich crustal root and (iv) excavation resulting from a later tectonic event unrelated to that resulting in the formation of the granulites. The later event might be triggered by the delamination of the garnet-rich, lowermost crust.

Notes: Mafic garnet-bearing granulites from Sostrene Island, 150 km southwest of Davis Station on the coast of Prydz Bay, East Antarctica, exhibit two-stage symplectic coronas on garnet, formed after peak metamorphic conditions (M1). An outer corona of Opx (Mg66) + Pl (An94–97) + minor Hbl mantles a finer-grained inner corona of Opx (Mg67) + Pl (An95–96) + Spl (Mg36). Both symplectites contain minor ilmenite–magnetite intergrowths. The finer-grained symplectite also occurs along a fracture cleavage in the garnet.The outer corona originated during a second metamorphic event (M2) via the reaction Grt + Cpx (Hbl) + SiO2= Opx + Pl (1), whereas the inner corona formed later in response to decompression and minor deformation, resulting in the fracture cleavage in the garnet, according to the reaction Grt = Opx + Pl + Spl (2). The grossular content of the garent (XGrs= 0.168) is almost exactly that which is required for the stoichiometric breakdown by reaction (2) (calculated XGrs= 0.167). The mafic rocks are silica undersaturated, and the SiO2 for reaction (1) was most probably derived externally from the surrounding felsic gneisses.Preferred P–T estimates for M1 based on garnet core (Prp40Alm42Grs17Sps1)–matrix Opx–Cpx–Hbl pairs are c. 10 kbar at 980°C. The fine-grained symplectite formed post-peak M2 at c. 7 kbar and 850°C. The enclosing felsic gneisses yield pressure estimates of between 5 and 7 kbar, which compare with conditions of c. 6 kbar and 775°C in the nearby Bolingen Islands. These lower P–T estimates are considered to be representative of the widespread 1100-Ma metamorphic event recognized in outcrops along the Prydz Bay coast. The high-P, high-T estimates derived from the garnet relics provide evidence for an earlier, possibly Archaean, high-grade metamorphic event.

Notes: Calc-silicate granulites from the Bolingen Islands, Prydz Bay, East Antarctica, exhibit a sequence of reaction textures that have been used to elucidate their retrograde P–T path. The highest temperature recorded in the calc-silicates is represented by the wollastonite- and scapolite-bearing assemblages which yield at least 760°C at 6 kbar based on experimental results. The calc-silicates have partially re-equilibrated at lower temperatures (down to 450°C) as evidenced by the successive reactions: (1) wollastonite + scapolite + calcite = garnet + CO2, (2) wollastonite + CO2= calcite + quartz, (3) wollastonite + plagioclase = garnet + quartz, (4) scapolite = plagioclase + calcite + quartz, (5) garnet + CO2+ H2O = epidote + calcite + quartz, and (6) clinopyroxene + CO2+ H2O = tremolite + calcite + quartz.The reaction sequence observed indicates that aCO2 was relatively low in the wollastonite-bearing rocks during peak metamorphic conditions, and may have been further lowered by local infiltration of H2O from the surrounding migmatitic gneisses on cooling. Fluid activities in the Bolingen calc-silicates were probably locally variable during the granulite facies metamorphism, and large-scale CO2 advection did not occur.A retrograde P–T path, from the sillimanite stability field (c. 760°C at 6 kbar) into the andalusite stability field (c. 450°C at 〈3 kbar), is suggested by the occurrence of secondary andalusite in an adjacent cordierite–sillimanite gneiss in which sillimanite occurs as inclusions in cordierite.

Notes: Many high-temperature–low-pressure (high-T–low-P) metamorphic terranes show evidence for peak mineral growth during crustal thickening strain increments at pressures near the maximum attained during the heating–cooling cycle. Such terranes are not readily explained as the conductive response to crustal thickening since the resulting Moho temperatures would greatly exceed the crustal liquidus and because heating due to conductive equilibration on length scales appropriate to lithospheric-scale strains must greatly outlast the deformation. Consequently, high-T–low-P metamorphism may be generated during crustal thickening only when significant heat is advected within the crust, as for example may occur during the segregation of granitic melts. We show that without the addition of asthenospheric melts and at strain rates appropriate to continental deformation the conditions required for significant lower crustal melting during deformation are only likely to be attained if heat flow into the lower crust during crustal thickening is increased substantially, for example, by removing the mantle part of the lithosphere. A simple parameterization of lithospheric deformation involving the vertical strain on the scale of the crust, c, and the lithosphere, 1 respectively, allows the potential energy of the evolving orogen to be readily evaluated. Using this parameterization we show that an important isostatic consequence of the deformation geometries capable of generating such high-T–low-P metamorphism during crustal thickening (with c1) is an imposed upper limit to crustal thicknesses which is much lower than for homogeneous deformations (fc= f1) for the same initial lithospheric configuration.

Notes: ‘Lower crustal’ suite xenoliths in basaltic and kimberlitic magmas are dominated by mafic granulites and may also include eclogites and garnet pyroxenites. Pressures of up to 25 kbar obtained from such xenoliths are well in excess of an upper value of c. 12 kbar for exposed granulite terranes. Palaeogeotherms constructed from xenoliths for the lower crust beneath the Phanerozoic fold belts of eastern Australia (SEA) and beneath the eastern margin of the Australian craton (EMAC) indicate two distinct thermal regimes. The two geotherms have similar form, with the EMAC curve displaced c. 150°C to lower temperatures. Reaction microstructures show the partial re-equilibration of primary igneous assemblages to granulite and eclogite assemblages and are interpreted to reflect the cooling from magmatic temperatures. Variations in mineral compositions and zoning are used to constrain further the history of several EMAC xenoliths to near-isobaric trajectories.Detailed graphical models are constructed to predict compositional changes for isobaric P–T paths (at 7, 14 & 21 kbar) to transform an SEA-type geotherm to a cratonic geotherm. The models show that for the assemblage grt + cpx ± ky + plag + qtz, the changes associated with falling temperature in Xgr, Xjd (increase) and Xan (decrease) will be greater at higher pressures. These results indicate that discernible zoning is more likely to be preserved in the higher pressure xenoliths. The zoning recorded in clinopyroxene from mafic granulite xenoliths over the pressure range c. 12–22 kbar suggests isobaric cooling of a large crustal thickness (30–35 km).An isobaric cooling path is consistent with magma accretion models for the transition of a crust–mantle boundary from an SEA-type geotherm to a cratonic geotherm. The coexistence of granulite and eclogite over the depth range 35–75 km beneath the EMAC indicates that the granulite to eclogite transition in the lower crust is controlled by P–T conditions, bulk chemistry and kinetic factors. At shallower crustal levels, typified by exposed granulite terranes, isobaric cooling may not result in the transition to eclogite.

Notes: Isocon analysis has been applied to five sets of leucosome, mafic selvages and immediately adjacent mesosome in the migmatites from a 15-m outcrop in the Colorado Front Range. The results show: (i) mafic selvages formed from the adjacent mesosome by loss of felsic components and therefore the mesosomes are indeed palaeosomes or protoliths; (ii) the leucosomes did not form in a closed system from the palaeosome (in which case the material lost from the palaeosome during selvage formation would become the leucosome). The observed volumes and compositions of leucosomes require that the present leucosome must contain some material in addition to the felsic components lost from the selvages. The materials that must be added are leucotonalitic to granitic in composition, varying greatly in K/(Na + Ca) ratio. The trend in leucosome composition can be reproduced by assuming that a metasomatic exchange, KNa + Ca, modified originally leucotonalitic leucosomes to more K-rich compositions. These leucosomes most likely formed by injection of silicate melts accompanied, or followed, by metasomatism. The trend of leucosome compositions in this study reflects the general trend in the leucosome compositions which have been published from other areas, indicating that the proposed mechanism can be applicable to other regional migmatites.

Notes: Three types of zircon occur in a complexly deformed and variably migmatized quartzofeldspathic gneiss from the Reynolds Range, central Australia. The oldest type is inherited from the granitic precursor of the gneiss, and is overgrown by a second group of zircon grains that formed during prograde, granulite facies metamorphism. Partial melting of the gneiss resulted in solution of both the inherited and metamorphic zircon. No new zircon growth accompanied crystallization of the partial melt, suggesting loss of zirconium–rich residual fluids. Hydrous, amphibolite facies retrogression of the gneiss and its migmatized variants during late shearing produced new, idiomorphic zircon in both the shear zone and its wall rocks.Important implications of this study are that (i) zircon has a tendency to dissolve if it comes into direct contact with a melt produced from anhydrous biotite breakdown in a quartzofeldspathic granulite, (ii) melt crystallization is not necessarily accompanied by zircon growth, and (iii) euhedral zircon can grow from a hydrous fluid phase under subsolidus, amphibolite facies conditions, e.g. within shear zones.