ALBERT

Beschreibung: Abstract Low‐frequency passive integrated transponders (PIT tags), are commonly used for monitoring pebble mobility in gravel‐bed rivers. Although early studies reported high recovery rates for PIT tags used in small streams, recovery rates in larger systems remain low, substantially limiting the possibilities for their use in such rivers. These low recovery rates are potentially due to missed detections caused by tag signal collision, burial in the sediment layer deeper than the maximum detection range and insufficient (but still exhausting) field effort to cover the concerned areas. A potential solution for addressing these problems is to use active ultra‐high frequency (a‐UHF) transponders as these have a greater detection range and anti‐collision protocols. In order to assess the potential of such transponders for pebble tracking in rivers, we used 433.92 MHz COIN‐ID and COIN‐HC models (ELA Innovation Company, Montpellier, France). We completed several tests to (i) characterize transponder detection ranges in the water and in saturated sediment and (ii) develop field protocols for locating tags by combining global positioning systems (GPS) sites and transponder received signal strength indication (RSSI) levels. The results showed that (i) the maximum detection ranges are about 2.4 m in the water column and more than 2.6 m in a column of saturated gravelly‐sandy sediment, (ii) RSSI spatial interpolation can be used to determine transponder position with good accuracy (〈 1 m), (iii) the desired minimal level of accuracy can be adjusted depending on in‐field effort and signal impulse interval, (iv) the RSSI maximal value observed cannot yet be used to determine transponder burial depth because of the multipath propagation of radio frequencies and the semi‐directional emission of the tag signal. Copyright © 2017 John Wiley & Sons, Ltd.

Beschreibung: Abstract Single bed load particle impacts were experimentally investigated in supercritical open channel flow over a fixed planar bed of low relative roughness height simulating high‐gradient non‐alluvial mountain streams as well as hydraulic structures. Particle impact characteristics (impact velocity, impact angle, Stokes number, restitution and dynamic friction coefficients) were determined for a wide range of hydraulic parameters and particle properties. Particle impact velocity scaled with the particle velocity, and the vertical particle impact velocity increased with excess transport stage. Particle impact and rebound angles were low and decreased with transport stage. Analysis of the particle impacts with the bed revealed almost no viscous damping effects with high normal restitution coefficients exceeding unity. The normal and resultant Stokes numbers were high and above critical thresholds for viscous damping. These results are attributed to the coherent turbulent structures near the wall region, i.e. bursting motion with ejection and sweep events responsible for turbulence generation and particle transport. The tangential restitution coefficients were slightly below unity and the dynamic friction coefficients were lower than for alluvial bed data, revealing that only a small amount of horizontal energy was transferred to the bed. The abrasion prediction model formed by Sklar and Dietrich in 2004 was revised based on the new equations on vertical impact velocity and hop length covering various bed configurations. The abrasion coefficient kv was found to be vary around kv ~ 105 for hard materials (tensile strength ft 〉 1 MPa), one order of magnitude lower than the value assumed so far for Sklar and Dietrich's model. Copyright © 2017 John Wiley & Sons, Ltd.

Beschreibung: Abstract When fine sediments are present in gravel streambeds (gravel‐framework beds), the gravel can be more easily removed from its original position, compared with gravel in a streambed without fine sediment but otherwise under the same hydraulic conditions. In this study, the effect of the presence of sand on the initiation of gravel motion in gravel riverbeds was investigated using flume experiments. The relationship between the critical Shields stress for gravel motion initiation and the fraction of sand in the bed was determined experimentally. The results can be summarized as follows. (1) When the fraction of sand in the bed is smaller than about 0.4, the critical Shields stress for the initiation of gravel motion decreases with increasing fraction of sand. The critical Shields stress increases, however, with increasing fraction of sand when it is larger than about 0.4. (2) The difference between the value of the critical Shields stress predicted by the Egiazaroff equation and the value obtained from the experimental data becomes maximum at about 0.4 of the fraction of sand. Here an empirical relation between the critical Shields stress and the fraction of sand is proposed so as to consider the effects of the ratio of the characteristic gravel size to the mean size of the bed material on the critical Shields stress. (3) Gravel in armored beds can be more easily mobilized by supplying sand as part of a sediment augmentation scheme. The sand fraction in the subsurface layer of the bed appears to reduce the friction angle of exposed particles. Sediment augmentation using sand has been recently demonstrated to be a viable alternative for mobilizing gravel for the restoration of gravel‐bed rivers downstream of dams. The quantitative evaluation obtained through the experiments reported here may be useful for the design of augmentation schemes. Copyright © 2017 John Wiley & Sons, Ltd.

Beschreibung: Abstract The assumption of the equilibrium state of gravel surfaces in flume experiments under feeding or recirculating conditions is generally justified by three equilibrium criteria based on sediment transport, slopes, and bed features. When these parameters become stable, an experiment is expected to reach equilibrium. This equilibrium state, however, is based on a one‐dimensional model, the Exner equation, which may not truly reflect the equilibrium state of the system considering the complex flow and sediment processes. In this paper, the evolutionary process of a gravel surface is investigated based on a large‐scale recirculating flume experiment. The performances of the three equilibrium criteria are evaluated first, and then the evolution of the bed morphology is studied. The key findings include the following: (1) the sediment transport rate, slopes of water and bed surfaces, and one‐dimensional morphological features reach equilibrium roughly simultaneously; (2) two‐dimensional morphology continually evolves after these characteristics reach equilibrium, which is confirmed by the characteristics of the sediment transport process; and (3) the results from a numerical simulation suggest that a much longer time is required to reach an equilibrium state. Our results suggest that sufficient experimental time is required to investigate the equilibrium morphological characteristics of gravel surfaces, which is much longer than the equilibrium time reflected by the one‐dimensional equilibrium criteria. Copyright © 2017 John Wiley & Sons, Ltd.

Beschreibung: ABSTRACT Signals from growth factors or mechanical stimuli converge to promote vascular smooth muscle cell (VSMC) migration and proliferation, key events in the pathogenesis of intimal hyperplasia upon vascular injury. Spry1, a regulator of receptor tyrosine kinases (RTK), plays a role in maintaining the contractile phenotype of VSMC. The aim of the current study was to determine the role of Spry1 in VSMC proliferation in vitro and injury induced neointimal hyperplasia in vivo. VSMC proliferation and neointima formation were evaluated in cultured human aortic SMC (hAoSMC) and ligation-induced injury of mouse carotid arteries from Spry1 gene targeted mice, and their corresponding wild type littermates. Human Spry1 or non-targeting control lentiviral shRNAs were used to knock down Spry1 in hAoSMC. Time course cell cycle analysis showed a reduced fraction of S-phase cells at 12 and 24 hours after growth medium stimulation in Spry1 shRNA transduced hAoSMC. Consistent with reduced S-phase entry, the induction of cyclinD1 and the levels of pRbS807/S811, pH3Ser10, and pCdc2 were also reduced, while the cell cycle inhibitor p27 Kip1 was maintained in Spry1 knockdown hAoSMC. In vivo, loss of Spry1 attenuated carotid artery ligation-induced neointima formation in mice, and this effect was accompanied by a decrease in cell proliferation similar to the in vitro results. Our findings demonstrate that loss of Spry1 attenuates mitogen-induced VSMC proliferation, and thus injury-induced neointimal hyperplasia likely via insufficient activation of Akt signaling causing decreased cyclinD1 and increased p27 Kip1 and a subsequent decrease in Rb and cdc2 phosphorylation. This article is protected by copyright. All rights reserved

Beschreibung: ABSTRACT The Late Pleistocene Middle Stone Age (MSA) record of Africa provides early examples of standardised stone tool production and complex manufacturing sequences, superficially implying a long-term trend towards greater complexity in MSA technology at a continental scale. However, at this scale, spatial and temporal expressions of technological complexity are uneven. New lithic and chronometric data from the East–Central African record add further regional perspective to these patterns. Stone artefact assemblages from Karonga, northern, Malawi (92–22 ka), persistently lack the complexity demonstrated elsewhere in Africa at the same times, despite similar lithic raw materials. These new data provide an essential avenue for exploring hypotheses about the roles of environmental risk and demography in shaping the expression of MSA technology across the continent, not just at a local scale. When set within this framework, the simplicity of the Karonga MSA is best explained by its position in an environment that was persistently low in relative extrinsic subsistence risk. These results reinforce that motivations to invest in complex tools were variable through space and time, and that this variation, more than factors relating to behavioural capacity, may explain the patchy evidence for lithic complexity in the later MSA.

Beschreibung: Analog forecasting is a mechanism-free nonlinear method that forecasts a system forward in time by examining how past states deemed similar to the current state moved forward. Previous applications of analog forecasting has been successful at producing robust forecasts for a variety of ecological and physical processes, but it has typically been presented in an empirical or heuristic procedure, rather than as a formal statistical model. The methodology presented here extends the model-based analog method of McDermott and Wikle (Environmetrics, 27, 2016, 70) by placing analog forecasting within a fully hierarchical statistical framework that can accommodate count observations. Using a Bayesian approach, the hierarchical analog model is able to quantify rigorously the uncertainty associated with forecasts. Forecasting waterfowl settling patterns in the northwestern United States and Canada is conducted by applying the hierarchical analog model to a breeding population survey dataset. Sea surface temperature (SST) in the Pacific Ocean is used to help identify potential analogs for the waterfowl settling patterns. This paper develops a hierarchical analog forecasting model for high-dimensional spatio-temporal count valued data. Analog forecasting is a flexible nonlinear forecasting method that has found success in a variety of fields such as ecology and meteorology. The proposed model is implemented in a hierarchical Bayesian framework allowing us to rigorously quantify the uncertainty associated with the produced forecasts. To our knowledge, this is the first hierarchical analog model for non-Gaussian data. We apply the proposed model to the forecasting of waterfowl settling patterns by using Sea Surface Temperature (SST) to find potential analogs for the waterfowl settling patterns.

Beschreibung: The Bulletin of the Ecological Society of America, Page 345-348, October 2018. 〈br/〉

Beschreibung: The Bulletin of the Ecological Society of America, Page 1-106, October 2018. 〈br/〉

Beschreibung: 〈b〉Ecology Day〈/b〉〈br〉 Maria Amélia Martins Loução〈br〉 Web Ecol., 17, 65-67, https://doi.org/10.5194/we-17-65-2017, 2017〈br〉 Following the 150th anniversary of the science of ecology, the Portuguese Ecological Society (SPECO) proposes 14 September as Ecology Day. This day should be promoted by ecological societies to host different kinds of public and media events closely related to ecology, in a broad sense. The date, 14 September, was chosen because it was on that day Haeckel had published his 〈q〉Ökologie und Chorologie〈/q〉.

Beschreibung: 〈b〉The ecology of subindividual variability in plants: patterns, processes, and prospects〈/b〉〈br〉 Carlos M. Herrera〈br〉 Web Ecol., 17, 51-64, https://doi.org/10.5194/we-17-51-2017, 2017〈br〉 Plants produce a considerable number of structures of one kind, like leaves, flowers, fruits, and seeds, which are not identical. This paper provides an overview of current knowledge on traits that vary subindividually, the magnitude of subindividual variation, and its spatial patterning. Examples are presented on the consequences of subindividual variation for plants and consumers. Emerging links between genetics, epigenetics, subindividual variation, and population ecology are also considered.

Beschreibung: The Bulletin of the Ecological Society of America, Page 1-1, October 2018. 〈br/〉

Beschreibung: The Bulletin of the Ecological Society of America, Page 265-268, October 2018. 〈br/〉

Beschreibung: 〈b〉Could disruptive technologies also reform academia?〈/b〉〈br〉 Casparus J. Crous〈br〉 Web Ecol., 17, 47-50, https://doi.org/10.5194/we-17-47-2017, 2017〈br〉 A thriving future science community could depend on disruptive technologies to shake up outmoded academic practices.

Beschreibung: Abstract In meandering rivers cut into bedrock, erosion across a channel cross‐section can be strongly asymmetric. At a meander apex, deep undercutting of the outer bank can result in the formation of a hanging cliff (which may drive hillslope failure), whereas the inner bank adjoins a slip‐off slope that connects to the hillslope itself. Here we propose a physically‐based model for predicting channel planform migration and incision, point bar and slip‐off slope formation, bedrock abrasion, the spatial distribution of alluvial cover, and adaptation of channel width in a mixed bedrock‐alluvial channel. We simplify the analysis by considering a numerical model of steady, uniform bend flow satisfying cyclic boundary conditions. Thus in our analysis, ‘sediment supply’, i.e. the total volume of alluvium in the system, is conserved. In our numerical simulations, the migration rate of the outer bank is a specified parameter. Our simulations demonstrate the existence of an approximate state of dynamic equilibrium corresponding to a near‐solution of permanent form in which a bend of constant curvature, width, cross‐sectional shape and alluvial cover distribution migrates diagonally downward at constant speed, leaving a bedrock equivalent of a point bar on the inside of the bend. Channel width is set internally by the processes of migration and incision. We find that equilibrium width increases with increasing sediment supply, but is insensitive to outer bank migration rate. The slope of the bedrock point bar varies inversely with both outer bank migration rate and sediment supply. Although the migration rate of the outer bank is externally imposed here, we discuss a model modification that would allow lateral side‐wall abrasion to be treated in a manner similar to the process of bedrock incision. Copyright © 2016 John Wiley & Sons, Ltd.

Beschreibung: Abstract Particle dynamics are investigated experimentally in supercritical high‐speed open channel flow over a fixed planar bed of low relative roughness height simulating flows in high‐gradient non‐alluvial mountain streams and hydraulic structures. Non‐dimensional equations were developed for transport mode, particle velocity, hop length and hop height accounting for a wide range of literature data encompassing sub‐ and supercritical flow conditions as well as planar and alluvial bed configurations. Particles were dominantly transported in saltation and particle trajectories on planar beds were rather flat and long compared with alluvial bed data due to (1) increased lift forces by spinning motion, (2) strongly downward directed secondary currents, and (3) a planar flume bed where variation in particle reflection and damping effects were minor. The analysis of particle saltation trajectories revealed that the rising and falling limbs were almost symmetrical contradicting alluvial bed data. Furthermore, no or negligible effect of particle size and shape on particle dynamics were found. Implications of experimental findings for mechanistic saltation‐abrasion models are briefly discussed. Copyright © 2017 John Wiley & Sons, Ltd.

Beschreibung: Abstract Large wood along rivers influences entrainment, transport, and storage of mineral sediment and particulate organic matter. We review how wood alters sediment dynamics and explore patterns among volumes of in‐stream wood, sediment storage, and residual pools for dispersed pieces of wood, logjams, and beaver dams. We hypothesized that: volume of sediment per unit area of channel stored in association with wood is inversely proportional to drainage area; the form of sediment storage changes downstream; sediment storage correlates with wood load; the residual volume of pools created in association with wood correlates inversely with drainage area; and volume of sediment stored behind beaver dams correlates with pond area. Lack of data from larger drainage areas limits tests of these hypotheses, but the analyses suggest that sediment volume correlates positively with drainage area and wood volume. The form of sediment storage in relation to wood appears to change downstream, with wedges of sediment upstream from jammed steps most prevalent in small, steep channels and more dispersed sediment storage in lower gradient channels. Pool volume correlates positively with wood volume and negatively with channel gradient. Sediment volume correlates well with beaver pond area. More abundant in‐stream wood and beaver populations present historically equated to greater sediment storage within river corridors and greater residual pool volume. One implication of these changes is that protecting and re‐introducing wood and beavers can be used to restore rivers. This review of the existing literature on wood and sediment dynamics highlights the lack of studies on larger rivers. Copyright © 2016 John Wiley & Sons, Ltd.

Beschreibung: Abstract For more than 150 years, humans have tried to limit the geomorphic activity of mountain streams, and the related damage, using torrent control works. Check dams are likely the most emblematic civil engineering structures used in soil conservation programs. Modern mountain societies have inherited thousands of these structures built in upland gullies and streams. To help define their effectiveness and decisions concerning their maintenance or new project designs, a clear understanding of potential effects of check dams on river systems, i.e. their functions, is first needed. The next steps concern quantitative assessments of each function on the flood features and combination of all effects. The present understanding of these sometimes old structures' functions can be complicated because the societal and environmental contexts in which the original structures were built may have changed. To bridge this gap, this paper traces the purposes for which check dams were built, through a detailed analysis of French archives. We first analyze chronologically how each function was theorized and applied in the field. In the nineteenth century, engineers developed a thorough empirical and conceptual knowledge of mountain soil erosion, torrential geomorphology, and sediment transport processes as well as check dam interactions with these natural processes. The second part of this paper synthesizes conceptual descriptions of the check dams' functions, in the light of more than 150 years of experience, with their implication on the features of the structures. The French experience is compared to other countries' pioneering works. Finally, the next steps and remaining research challenges toward a comprehensive analysis of check dams' efficiency in torrent hazard mitigation are presented. This analysis is proposed to remind how, conceptually, check dams may influence geomorphic systems, bearing in mind the knowledge represented in pioneer guidelines and recent works on the subject. Copyright © 2016 John Wiley & Sons, Ltd.

Beschreibung: Abstract Structure‐from‐Motion (SfM) photogrammetry is now used widely to study a range of earth surface processes and landforms, and is fast becoming a core tool in fluvial geomorphology. SfM photogrammetry allows extraction of topographic information and orthophotos from aerial imagery. However, one field where it is not yet widely used is that of river restoration. The characterisation of physical habitat conditions pre‐ and post‐restoration is critical for assessing project success, and SfM can be used easily and effectively for this purpose. In this paper we outline a workflow model for the application of SfM photogrammetry to collect topographic data, develop surface models and assess geomorphic change resulting from river restoration actions. We illustrate the application of the model to a river restoration project in the NW of England, to show how SfM techniques have been used to assess whether the project is achieving its geomorphic objectives. We outline the details of each stage of the workflow, which extend from preliminary decision‐making related to the establishment of a ground control network, through fish‐eye lens camera testing and calibration, to final image analysis for the creation of facies maps, the extraction of point clouds, and the development of digital elevation models (DEMs) and channel roughness maps. The workflow enabled us to confidently identify geomorphic changes occurring in the river channel over time, as well as assess spatial variation in erosion and aggradation. Critical to the assessment of change was the high number of ground control points and the application of a minimum level of detection threshold used to assess uncertainties in the topographic models. We suggest that these two things are especially important for river restoration applications. Copyright © 2016 John Wiley & Sons, Ltd.

Beschreibung: Abstract Experiments were undertaken to study the nature of granular interaction in running water by examining the influence of fine grain inputs to a coarser sediment bed with a mobile surface. Video recordings of grain sorting by both kinetic sieving and spontaneous percolation are used to diagnose the critical processes controlling the overall bed response. Kinetic sieving takes place in the mobile bed surface, with the finer sediment moving to the bottom of the bedload transport layer at the interface with the underlying quasi‐static coarse bed. We show that the behavior at this interface dictates how a channel responds to a fine sediment input. If, by spontaneous percolation, the fine sediment is able to infiltrate into the underlying quasi‐static bed, the total transport increases and the channel degrades. However, if the fine sediment input rate exceeds the transport capacity or is geometrically unable to infiltrate into the underlying bed, it forms a quasi‐static layer underneath the transport layer that inhibits entrainment from the underlying bed, resulting in aggradation and an increase in bed slope. Copyright © 2016 John Wiley & Sons, Ltd.

Beschreibung: Topographic monitoring of a gravel augmentation during a dam‐controlled flood in the Trinity River, CA, indicates that all of the gravel entering the study reach was captured in one of two bed‐material storage reservoirs. Such interactions with storage reservoirs can cause large bed‐material pulses to disperse by fragmenting into multiple smaller pulses. As a refinement to the conceptual model of sediment pulse evolution by dispersion and translation, the concept of pulse fragmentation has practical implications for gravel management. Abstract The geomorphic effect of introducing a gravel augmentation totaling 520 m3 into a gravel‐bed stream during a dam‐controlled flood in May of 2015 was monitored with bedload transport measurements, an array of seismometers, and repeated topographic surveys. Half of the augmented gravel was injected into the flow with front‐end loaders on the rising limb of the flood and the other half was injected on the first day of the peak. Virtually all of the gravel transported past the injection point was deposited within about 7 to 10 channel widths of the injection point. Most of the injected gravel deposited along the left bank of the river whereas the right half of the channel bed was dominated by scour. The downstream third of the depositional area consisted of a small dune field that developed prior to the second gravel injection and subsequently migrated about one channel width downstream. A second depositional front was observed upstream from the gravel injection point, where a delta‐like wedge of bed material developed in the first hours of the flow release and changed little over the remainder of the release. These two depositional areas represent small‐scale bed‐material storage reservoirs with the potential to accumulate and periodically release packets of bed material. Interactions with such storage reservoirs are hypothesized to cause large bed‐material pulses to disperse by fragmenting into multiple smaller pulses. As a refinement to the conceptual model that views sediment pulse evolution in terms of dispersion and translation, the concept of pulse fragmentation has practical implications for gravel management. It implies that gravel augmentations can produce morphologic changes at locations that are separated from the augmentation point by arbitrarily long reaches, and it highlights the dependence of pulse propagation rates on the nature and distribution of the bed‐material storage reservoirs in the channel system. Copyright © 2017 John Wiley & Sons, Ltd.

Beschreibung: Abstract The artificial gravel augmentation of river channels is increasingly being used to mitigate the adverse effects of river regulation and sediment starvation. A systematic framework for designing and assessing such gravel augmentations is still lacking, notably on large rivers. Monitoring is required to quantify the movement of augmented gravel, measure bedform changes, assess potential habitat enhancement, and reduce the uncertainty in sediment management. Here we present the results of an experiment conducted in the Rhine River (French and German border). In 2010, 23 000 m3 of sediments (approximately the mean annual bedload transport capacity) were supplied in a by‐passed reach downstream of the Kembs dam to test the feasibility of enhancing sediment transport and bedform changes. A 620‐m‐long and 12‐m‐wide gravel deposit was created 8 km downstream from the dam. Monitoring included topo‐bathymetric surveys, radio‐frequency particle tracking using passive integrated transponder (PIT) tags, bed grain size measurement, and airborne imagery. Six surveys performed since 2009 have been described (before and after gravel augmentation, and after Q2 and Q15 floods). The key findings are that (i) the augmented gravel was partially dispersed by the first flood event of December 2010 (Q1); (ii) PIT tags were found up to 3200 m downstream of the gravel augmentation site after four years, but the effects of gravel augmentation could not be clearly distinguished from the effects of floods and internal remobilization on more than 3500 m downstream; (iii) linear and log‐linear relationships linking bedload transport, particle mobility, and grain size were established; and (iv) combined bathymetry and PIT tag surveys were useful for evaluating potential environmental risks and the first morpho‐ecological responses. This confirmed the complementary nature of such techniques in the monitoring of gravel augmentation in large rivers. Copyright © 2017 John Wiley & Sons, Ltd.

Beschreibung: Mountain gravel‐bed rivers are subjected to punctuated floods and sediment delivery. We model this numerically in terms of a cycled hydrograph upstream and a cycled “sedimentograph” midreach. Both the hydrograph and the sedimentograph generate boundary layers, within which the effect of the fluctuations are felt. Outside the boundary layers, steady, uniform conditions representing the overall effects of the hydrograph and sedimentograph are achieved. Our result provides a useful tool for simplifying the modeling of long‐term morphodynamics in mountain rivers. Abstract Sediment often enters rivers in the form of sediment pulses associated with landslides and debris flows. This is particularly so in gravel‐bed rivers in earthquake‐prone mountain regions, such as Southwest China. Under such circumstances, sediment pulses can rapidly change river topography and leave the river in repeated states of gradual recovery. In this paper, we implement a one‐dimensional morphodynamic model of river response to pulsed sediment supply. The model is validated using data from flume experiments, so demonstrating that it can successfully reproduce the overall morphodynamics of experimental pulses. The model is then used to explore the evolution of a gravel‐bed river subject to cycled hydrographs and repeated sediment pulses. These pulses are fed into the channel in a fixed region centered at a point halfway down the calculational domain. The pulsed sediment supply is in addition to a constant sediment supply at the upstream end. Results indicate that the river can reach a mobile‐bed equilibrium in which two regions exist within which bed elevation and surface grain size distribution vary periodically in time. One of these is at the upstream end, where a periodic discharge hydrograph and constant sediment supply are imposed, and the other is in a region about halfway down the channel where periodic sediment pulses are introduced. Outside these two regions, bed elevation and surface grain size distribution reach a mobile‐bed equilibrium that is invariant in time. The zone of fluctuation‐free mobile‐bed equilibrium upstream of the pulse region is not affected by repeated sediment pulses under the scenarios tested, but downstream of the pulse region, the channel reaches different fluctuation‐free mobile‐bed equilibriums under different sediment pulse scenarios. The vertical bed structure predicted by the simulations indicates that the cyclic variation associated with the hydrograph and sediment pulses can affect the substrate stratigraphy to some depth. Copyright © 2017 John Wiley & Sons, Ltd.

Beschreibung: Abstract Large wood (LW) is a ubiquitous feature in rivers of forested watersheds worldwide, and its importance for river diversity has been recognized for several decades. Although the role of LW in fluvial dynamics has been extensively documented, there is a need to better quantify the most significant components of LW budgets at the river scale. The purpose of our study was to quantify each component (input, accumulation, and output) of a LW budget at the reach and watershed scales for different time periods (i.e. a 50‐year period, decadal cycle, and interannual cycle). The LW budget was quantified by measuring the volumes of LW inputs, accumulations, and outputs within river sections that were finally evacuated from the watershed. The study site included three unusually large but natural wood rafts in the delta of the Saint‐Jean River (SJR; Québec, Canada) that have accumulated all LW exported from the watershed for the last 50 years. We observed an increase in fluvial dynamics since 2004, which led to larger LW recruitment and a greater LW volume trapped in the river corridor, suggesting that the system is not in equilibrium in terms of the wood budget but is rather recovering from previous human pressures as well as adjusting to hydroclimatic changes. The results reveal the large variability in the LW budget dynamics during the 50‐year period and allow us to examine the eco‐hydromorphological trajectory that highlights key variables (discharge, erosion rates, bar surface area, sinuosity, wood mobility, and wood retention). Knowledge on the dynamics of these variables improves our understanding of the historical and future trajectories of LW dynamics and fluvial dynamics in gravel‐bed rivers. Extreme events (flood and ice‐melt) significantly contribute to LW dynamics in the SJR river system. Copyright © 2017 John Wiley & Sons, Ltd.

Beschreibung: Abstract The question: ‘how does a streambed change over a minor flood?’ does not have a clear answer due to lack of measurement methods during high flows. We investigate bedload transport and disentrainment during a 1.5‐year flood by linking field measurements using fiber optic distributed temperature sensing (DTS) cable with sediment transport theory and an existing explicit analytical solution to predict depth of sediment deposition from amplitude and phase changes of the diurnal near‐bed pore‐water temperature. The method facilitates the study of gravel transport by using near‐bed temperature time series to estimate rates of sediment deposition continuously over the duration of a high flow event coinciding with bar formation. The observations indicate that all gravel and cobble particles present were transported along the riffle at a relatively low Shields Number for the median particle size, and were re‐deposited on the lee side of the bar at rates that varied over time during a constant flow. Approximately 1–6% of the bed was predicted to be mobile during the 1.5‐year flood, indicating that large inactive regions of the bed, particularly between riffles, persist between years despite field observations of narrow zones of local transport and bar growth on the order ~3–5 times the median particle size. In contrast, during a seven‐year flood approximately 8–55% of the bed was predicted to become mobile, indicating that the continuous along‐stream mobility required to mobilize coarse gravel through long pools and downstream to the next riffle is infrequent. Copyright © 2017 John Wiley & Sons, Ltd.

Beschreibung: Abstract Piping has been recognized as an important geomorphic, soil erosion and hydrologic process. It seems that it is far more widespread than it has often been supposed. However, our knowledge about piping dynamics and its quantification currently relies on a limited number of data for mainly loess‐derived areas and marl badlands. Therefore, this research aimed to recognize piping dynamics in mid‐altitude mountains under a temperate climate, where piping occurs in Cambisols, not previously considered as piping‐prone soils. It has been expressed by the estimation of erosion rates due to piping and elongation of pipes in the Bereźnica Wyżna catchment in the Bieszczady Mountains, eastern Carpathians (305 ha, 188 collapsed pipes). The research was based on the monitoring of selected piping systems (1971–1974, 2013–2016). Changes in soil loss vary significantly between different years (up to 27.36 t ha−1 yr−1), as well as between the mean short‐term erosion rate (up to 13.10 t ha−1 yr−1), and the long‐term (45 years) mean of 1.34 t ha−1 yr−1. The elongation of pipes also differs, from no changes to 36 m during one year. The mean total soil loss is 48.8 t ha−1 in plots, whereas in the whole studied catchment it is 2.0 t ha−1. Hence, piping is both spatially and temporally dependent. The magnitude of piping in the study area is at least three orders of magnitude higher than surface erosion rates (i.e. sheet and rill erosion) under similar land use (grasslands), and it is comparable to the magnitude of surface soil erosion on arable lands. It means that piping constitutes a significant environmental problem and, wherever it occurs, it is an important, or even the main, sediment source. Copyright © 2017 John Wiley & Sons, Ltd.