ALBERT

Description: An Unmanned Aerial System (UAS) has been developed which is based on an aerodynamically functionalized planar wideband antenna. The antenna utilizes a planar circular dipole metallization scheme. The aerodynamic structure implements a planform similar to the Nutball flier, a hobbyist flight architecture. The resulting codesign achieved a large impedance bandwidth defined by a voltage standing wave ratio (VSWR) less than 2 from 100 MHz to over 2 GHz and omnidirectional dipole-like radiation patterns at the lower frequency region and more directional patterns at higher frequencies.

Description: Multirotor is the umbrella term for the family of unmanned aircraft, which include the quadrotor, hexarotor and other vertical take-off and landing (VTOL) aircraft that employ multiple main rotors for lift and control. Development and testing of novel multirotor designs has been aided by the proliferation of 3D printing and inexpensive flight controllers and components. Different multirotor configurations exhibit specific strengths, while presenting unique challenges with regards to design and control. This article highlights the primary differences between three multirotor platforms: a quadrotor; a fully-actuated hexarotor; and an octorotor. Each platform is modelled and then controlled using non-linear dynamic inversion. The differences in dynamics, control and performance are then discussed.

Description: This numerical study focuses on the fire phenomenology associated with the presence of a composite-type aircraft immersed, at one particular location and orientation, within a large aviation-fuel fire in a moving fluid medium. An extension of the eddy dissipation concept is incorporated, allowing one to investigate the roles of the wind speed and its direction on the fire growth, heat flux distribution and smoke products, such as carbon monoxide and soot. The predicted flame shape compares well with the measurements for an intermediate-scale fire. The outcome of the study is interesting, and the interaction model between turbulence and combustion is indeed adequate. The prediction indicates that interaction between the large object and fire environment combined with the influence of wind conditions dramatically affects the continuous flame shape. The increase of the wind speed results in an alteration of the distribution of the incident heat fluxes to the engulfed fuselage skin for a case where the fire and fuselage are of comparable size. The highest heat flux occurs on the windward side of the fuselage for the low and medium winds, but on the leeward side of the fuselage for the high wind. The peak in heat flux to the medium or high wind is almost equal in magnitude, but about a factor four increase of that to the low wind.

Description: The manta is the largest marine organism to swim by dorsoventral oscillation (flapping) of the pectoral fins. The manta has been considered to swim with a high efficiency stroke, but this assertion has not been previously examined. The oscillatory swimming strokes of the manta were examined by detailing the kinematics of the pectoral fin movements swimming over a range of speeds and by analyzing simulations based on computational fluid dynamic potential flow and viscous models. These analyses showed that the fin movements are asymmetrical up- and downstrokes with both spanwise and chordwise waves interposed into the flapping motions. These motions produce complex three-dimensional flow patterns. The net thrust for propulsion was produced from the distal half of the fins. The vortex flow pattern and high propulsive efficiency of 89% were associated with Strouhal numbers within the optimal range (0.2–0.4) for rays swimming at routine and high speeds. Analysis of the swimming pattern of the manta provided a baseline for creation of a bio-inspired underwater vehicle, MantaBot.

Description: A recent alleged “drone” collision with a British Airways Airbus A320 at Heathrow Airport highlighted the need to understand civil Remotely Piloted Aircraft Systems (RPAS) accidents and incidents (events). This understanding will facilitate improvements in safety by ensuring efforts are focused to reduce the greatest risks. One hundred and fifty two RPAS events were analyzed. The data was collected from a 10-year period (2006 to 2015). Results show that, in contrast to commercial air transportation (CAT), RPAS events have a significantly different distribution when categorized by occurrence type, phase of flight, and safety issue. Specifically, it was found that RPAS operations are more likely to experience (1) loss of control in-flight, (2) events during takeoff and in cruise, and (3) equipment problems. It was shown that technology issues, not human factors, are the key contributor in RPAS events. This is a significant finding, as it is contrary to the industry view which has held for the past quarter of a century that human factors are the key contributor (which is still the case for CAT). Regulators should therefore look at technologies and not focus solely on operators.

Description: An analysis of the kinematics of a flapping membrane wing using experimental kinematic data is presented. This motion capture technique tracks the positon of the retroreflective marker(s) placed on the left wing of a 1.3-m-wingspan ornithopter. The time-varying three-dimensional data of the wing kinematics were recorded for a single frequency. The wing shape data was then plotted on a two-dimensional plane to understand the wing dynamic behaviour of an ornithopter. Specifically, the wing tip path, leading edge bending, wing membrane shape, local twist, stroke angle and wing velocity were analyzed. As the three characteristic angles can be expressed in the Fourier series as a function of time, the kinematics of the wing can be computationally generated for the aerodynamic study of flapping flight through the Fourier coefficients presented. Analysis of the ornithopter wing showed how the ornithopter closely mimics the flight motions of birds despite several physical limitations.

Description: Technological advances have enabled the development of a number of optical fiber sensing methods over the last few years. The most prevalent optical technique involves the use of fiber Bragg grating (FBG) sensors. These small, lightweight sensors have many attributes that enable their use for a number of measurement applications. Although much literature is available regarding the use of FBGs for laboratory level testing, few publications in the public domain exist of their use at the operational level. Therefore, this paper gives an overview of the implementation of FBG sensors for large scale structures and applications. For demonstration, a case study is presented in which FBGs were used to determine the deflected wing shape and the out-of-plane loads of a 5.5-m carbon-composite wing of an ultralight aerial vehicle. The in-plane strains from the 780 FBG sensors were used to obtain the out-of-plane loads as well as the wing shape at various load levels. The calculated out-of-plane displacements and loads were within 4.2% of the measured data. This study demonstrates a practical method in which direct measurements are used to obtain critical parameters from the high distribution of FBG sensors. This procedure can be used to obtain information for structural health monitoring applications to quantify healthy vs. unhealthy structures.

Description: The advent, during the first decade of the 21st century, of the concept of acoustic metamaterial has disclosed an incredible potential of development for breakthrough technologies. Unfortunately, the extension of the same concepts to aeroacoustics has turned out to be not a trivial task, because of the different structure of the governing equations, characterized by the presence of the background aerodynamic convection. Some of the approaches recently introduced to circumvent the problem are biased by a fundamental assumption that makes the actual realization of devices extremely unlikely: the metamaterial should guarantee an adapted background aerodynamic convection in order to modify suitably the acoustic field and obtain the desired effect, thus implying the porosity of the cloaking device. In the present paper, we propose an interpretation of the metamaterial design that removes this unlikely assumption, focusing on the identification of an aerodynamically-impermeable metamaterial capable of reproducing the surface impedance profile required to achieve the desired scattering abatement. The attention is focused on a moving obstacle impinged by an acoustic perturbation induced by a co-moving source. The problem is written in a frame of reference rigidly connected to the moving object to couple the convective wave equation in the hosting medium with the inertially-anisotropic wave operator within the cloak. The problem is recast in an integral form and numerically solved through a boundary-field element method. The matching of the local wave vector is used to derive a convective design of the metamaterial applicable to the specific problem analyzed. Preliminary numerical results obtained under the simplifying assumption of a uniform aerodynamic flow reveal a considerable enhancement of the masking capability of the convected design. The numerical method developed shows a remarkable computational efficiency, completing a simulation of the entire field in a few minutes on mid-end workstations. The results are re-interpreted in term of boundary impedance, assuming a locally-reacting behavior of the outer boundary of the cloaking layer. The formulation is currently being extended to the analysis of arbitrarily complex external flows in order to remove the limitation of the background uniform stream in the host.

Description: This review describes a number of biologically inspired principles that have been applied to the visual guidance, navigation and control of Unmanned Aerial System (UAS). The current limitations of UAS systems are outlined, such as the over-reliance on GPS, the requirement for more self-reliant systems and the need for UAS to have a greater understanding of their environment. It is evident that insects, even with their small brains and limited intelligence, have overcome many of the shortcomings of the current state of the art in autonomous aerial guidance. This has motivated research into bio-inspired systems and algorithms, specifically vision-based navigation, situational awareness and guidance.

Description: The capability of flapping wings to generate lift is currently evaluated by using the lift coefficient C ¯ L , a dimensionless number that is derived from the basal equation that calculates the steady-state lift coefficient CL for fixed wings. In contrast to its simple and direct application to fixed wings, the equation for C ¯ L requires prior knowledge of the flow field along the wing span, which results in two integrations: along the wing span and over time. This paper proposes an alternate average normalized lift η ¯ L that is easy to apply to hovering and forward flapping flight, does not require prior knowledge of the flow field, does not resort to calculus for its solution, and its lineage is close to the basal equation for steady state CL. Furthermore, the average normalized lift η ¯ L converges to the legacy CL as the flapping frequency is reduced to zero (gliding flight). Its ease of use is illustrated by applying the average normalized lift η ¯ L to the hovering and translating flapping flight of bumblebees. This application of the normalized lift is compared to the same application using two widely-accepted legacy average lift coefficients: the first C ¯ L as defined by Dudley and Ellington, and the second lift coefficient by Weis-Fogh. Furthermore, it is shown that the average normalized lift η ¯ L has a physical meaning: that of the ratio of work exerted by the flapping wings onto the surrounding flow field and the kinetic energy available at the aerodynamic surfaces during the generation of lift. The working equation for the average normalized lift η ¯ L is derived and is presented as a function of Strouhal number, St.