ALBERT

Description: The pattern synthesis and activated element selection for conformal array is investigated based on hybrid particle swarm optimization-gravitational search algorithm (PSOGSA) in this paper. With the introduction of PSOGSA algorithm which is a novel hybrid optimization technique, the element excitations are optimized to obtain the desired pattern for conformal array in the case of considering uncoupled and coupled element pattern. Numerical simulation and full-wave electromagnetic calculation verify the advantage and efficiency of our method. Then, a novel strategy of activated element selection based on PSOGSA algorithm is proposed for saving the energy consumption in conformal array.

Description: A practical antenna design combined with a universal serial bus (USB) connector in close vicinity is proposed. In the proposed arrangement, the antenna unit consisted of two planar inverted F antennas (PIFAs) placed on the two sides of the USB connector. The antenna is located at the bottom of the mobile phone to avoid the crowded space on the top side of the phone where various mobile phone accessories are usually assigned. A diplexer is incorporated in the unit to alleviate the adverse effect of the metal USB connector on the radiating efficiency of the antenna. A prototype antenna was fabricated and tested and showed good coverage for GSM850/900/1800/1900, UMTS2100, and LTE700/2500 multibands operation. The overall performances demonstrated the good design of the proposed unit for mobile phone application.

Description: This paper proposes a new design technique for internal antenna development. The proposed method is based on the framework of topology optimization incorporated with three effective mechanisms favoring the building blocks of associated optimization problems. Conventionally, the topology optimization of antenna structures discretizes a design space into uniform and rectangular pixels. However, the defining length of the resultant building blocks is so large that the problem difficulty arises; furthermore, the order of the building blocks becomes extremely high, so genetic algorithms (GAs) and binary particle swarm optimization (BPSO) are not more efficient than the random search algorithm. In order to form tight linkage groups of building blocks, this paper proposes a novel approach to handle the design details. In particular, a nonuniform discretization is adopted to discretize the design space, and the initialization of GAs is assigned as orthogonal arrays (OAs) instead of a randomized population; moreover, the control map of GAs is constructed by ensuring the schema growth based on the generalized schema theorem. By using the proposed method, two internal antennas are thus successfully developed. The simulated and measured results show that the proposed technique significantly outperforms the conventional topology optimization.

Description: Nuclear power plants are highly complex systems and the issues related to their safety are of primary importance. Probabilistic safety assessment is regarded as the most widespread methodology for studying the safety of nuclear power plants. As maintenance is one of the most important factors for affecting the reliability and safety, an enhanced preventive maintenance optimization model based on a three-stage failure process is proposed. Preventive maintenance is still a dominant maintenance policy due to its easy implementation. In order to correspond to the three-color scheme commonly used in practice, the lifetime of system before failure is divided into three stages, namely, normal, minor defective, and severe defective stages. When the minor defective stage is identified, two measures are considered for comparison: one is that halving the inspection interval only when the minor defective stage is identified at the first time; the other one is that if only identifying the minor defective stage, the subsequent inspection interval is halved. Maintenance is implemented immediately once the severe defective stage is identified. Minimizing the expected cost per unit time is our objective function to optimize the inspection interval. Finally, a numerical example is presented to illustrate the effectiveness of the proposed models.

Description: An integrated deterministic and probabilistic safety analysis (IDPSA) was carried out to assess the performances of the firefighting means to be applied in a nuclear power plant. The tools used in the analysis are the code FDS (Fire Dynamics Simulator) for fire simulation and the tool MCDET (Monte Carlo Dynamic Event Tree) for handling epistemic and aleatory uncertainties. The combination of both tools allowed for an improved modelling of a fire interacting with firefighting means while epistemic uncertainties because lack of knowledge and aleatory uncertainties due to the stochastic aspects of the performances of the firefighting means are simultaneously taken into account. The MCDET-FDS simulations provided a huge spectrum of fire sequences each associated with a conditional occurrence probability at each point in time. These results were used to derive probabilities of damage states based on failure criteria considering high temperatures of safety related targets and critical exposure times. The influence of epistemic uncertainties on the resulting probabilities was quantified. The paper describes the steps of the IDPSA and presents a selection of results. Focus is laid on the consideration of epistemic and aleatory uncertainties. Insights and lessons learned from the analysis are discussed.

Description: In this paper we evaluate the impact of a power uprate on a pressurized water reactor (PWR) for a tsunami-induced flooding test case. This analysis is performed using the RISMC toolkit: the RELAP-7 and RAVEN codes. RELAP-7 is the new generation of system analysis codes that is responsible for simulating the thermal-hydraulic dynamics of PWR and boiling water reactor systems. RAVEN has two capabilities: to act as a controller of the RELAP-7 simulation (e.g., component/system activation) and to perform statistical analyses. In our case, the simulation of the flooding is performed by using an advanced smooth particle hydrodynamics code called NEUTRINO. The obtained results allow the user to investigate and quantify the impact of timing and sequencing of events on system safety. In addition, the impact of power uprate is determined in terms of both core damage probability and safety margins.

Description: In case of some nuclear power plants constructed at the soft soil sites, liquefaction should be analysed as beyond design basis hazard. The aim of the analysis is to define the postevent condition of the plant, definition of plant vulnerabilities, and identification of the necessary measures for accident management. In the paper, the methodology of the analysis of liquefaction effects for nuclear power plants is outlined. The procedure includes identification of the scope of the safety analysis and the acceptable limit cases for plant structures having different role from accident management point of view. Considerations are made for identification of dominating effects of liquefaction. The possibility of the decoupling of the analysis of liquefaction effects from the analysis of vibratory ground motion is discussed. It is shown in the paper that the practicable empirical methods for definition of liquefaction susceptibility provide rather controversial results. Selection of method for assessment of soil behaviour that affects the integrity of structures requires specific considerations. The case of nuclear power plant at Paks, Hungary, is used as an example for demonstration of practical importance of the presented results and considerations.

Description: The loss of off-site power (LOOP) event occurs when all electrical power to the nuclear power plant from the power grid is lost. Complete failure of both off-site and on-site alternating current (AC) power sources is referred to as a station blackout (SBO). Combined LOOP and SBO events are analyzed in this paper. The analysis is done for different time delays between the LOOP and SBO events. Deterministic safety analysis is utilized for the assessment of the plant parameters for different time delays of the SBO event. Obtained plant parameters are used for the assessment of the probabilities of the functional events in the SBO event tree. The results show that the time delay of the SBO after the LOOP leads to a decrease of the core damage frequency (CDF) from the SBO event tree. The reduction of the CDF depends on the time delay of the SBO after the LOOP event. The results show the importance of the safety systems to operate after the plant shutdown when the decay heat is large. Small changes of the basic events importance measures are identified with the introduction of the delay of the SBO event.

Description: This paper presents radio frequency (RF) capacity estimation for millimeter wave (mm-wave) based fifth-generation (5G) cellular networks using field-level simulations. It is shown that, by reducing antenna beamwidth from 65° to 30°, we can enhance the capacity of mm-wave cellular networks roughly by 3.0 times at a distance of 220 m from the base station (BS). This enhancement is far much higher than the corresponding enhancement of 1.2 times observed for 900 MHz and 2.6 GHz microwave networks at the same distance from the BS. Thus the use of narrow beamwidth transmitting antennas has more pronounced benefits in mm-wave networks. Deployment trials performed on an LTE TDD site operating on 2.6 GHz show that 6-sector site with 27° antenna beamwidth enhances the quality of service (QoS) roughly by 40% and more than doubles the overall BS throughput (while enhancing the per sector throughput 1.1 times on average) compared to a 3-sector site using 65° antenna beamwidth. This agrees well with our capacity simulations. Since mm-wave 5G networks will use arbitrary number of beams, with beamwidth much less than 30°, the capacity enhancement expected in 5G system when using narrow beamwidth antennas would be much more than three times observed in our simulations.

Description: Multipaths represent a common predominant and uncontrolled component on channel impairments for all terrestrial and Land Mobile Satellite systems. Without restrictions w.r.t mobile terrestrial applications, the addressed multipath problematic in this paper is focused on Land Mobile Satellite applications where delayed signal replicas are highly impacting performances on communication systems while they induce strong positioning errors for navigation systems. The actual trend in propagation channel modelling is to improve the multipath characterisation and representation by using semideterministic and hybrid physical-statistical models into channel simulators instead of narrow-band empirical approaches. In this context, this paper presents a new simplified model, called 3CM (3-Component Model) to reproduce building scattering in an efficient way which strongly improves computation performances. This model is based on asymptotic methods, namely, PO (Physical Optics) which allows the 3CM to be frequency scalable, polarimetric, and dielectric materials oriented. Note that the proposed model and the retained approach can be integrated into more complex tools such as existing ray tracers. However, this issue is not discussed in this paper.

Description: This work presents a full-wave analysis of stable frequency selective surfaces (FSSs) composed of periodic arrays of cross fractal patch elements. The shapes of these patch elements are defined conforming to a fractal concept, where the generator fractal geometry is successively subdivided into parts which are smaller copies of the previous ones (defined as fractal levels). The main objective of this work is to investigate the performance of FSSs with cross fractal patch element geometries including their frequency response and stability in relation to both the angle of incidence and polarization of the plane wave. The frequency response of FSS structures is obtained using the wave concept iterative procedure (WCIP). This method is based on a wave concept formulation and the boundary conditions for the FSS structure. Prototypes were manufactured and measured to verify the WCIP model accuracy. A good agreement between WCIP and measured results was observed for the proposed cross fractal FSSs. In addition, these FSSs exhibited good angular stability.

Description: The prediction of RF coverage in urban environments is now commonly considered a solved problem with tens of models proposed in the literature showing good performance against measurements. Among these, ray tracing is regarded as one of the most accurate ones available. In the present work, however, we show that a great deal of work is still needed to make ray tracing really unleash its potential in practical use. A very extensive validation of a state-of-the-art 3D ray tracing model is carried out through comparison with measurements in one of the most challenging environments: the city of San Francisco. Although the comparison is based on RF cellular coverage at 850 and 1900 MHz, a widely studied territory, very relevant sources of error and inaccuracy are identified in several cases along with possible solutions.

Description: A space-domain integral equation method accelerated with adaptive cross approximation (ACA) is presented for the fast and accurate analysis of electromagnetic (EM) scattering from multilayered metallic photonic crystal (MPC). The method directly solves for the electric field in order to easily enable the periodic boundary condition (PBC) in the spatial domain. The ACA is a purely algebraic method allowing the compression of fully populated matrices; hence, its formulation and implementation are independent of integral equation kernel (Green’s function). Therefore, the ACA is very well suited for accelerating integral equation analysis of periodic structure with the integral kernel of the periodic Green’s function (PGF). The computation of the spatial-domain periodic Green’s function (PGF) is accelerated by the modified Ewald transformation, such that the multilayered periodic structure can be analyzed efficiently and accurately. An effective interpolation method is also proposed to fast compute the periodic Green’s function, which can greatly reduce the time of matrix filling. Numerical examples show that the proposed method can greatly save the frequency sweep time for multilayered periodic structure.

Description: Integrated Deterministic-Probabilistic Safety Assessment (IDPSA) combines deterministic model of a nuclear power plant with a method for exploration of the uncertainty space. Huge amount of data is generated in the process of such exploration. It is very difficult to “manually” process and extract from such data information that can be used by a decision maker for risk-informed characterization, understanding, and eventually decision making on improvement of the system safety and performance. Such understanding requires an approach for interpretation, grouping of similar scenario evolutions, and classification of the principal characteristics of the events that contribute to the risk. In this work, we develop an approach for classification and characterization of failure domains. The method is based on scenario grouping, clustering, and application of decision trees for characterization of the influence of timing and order of events. We demonstrate how the proposed approach is used to classify scenarios that are amenable to treatment with Boolean logic in classical Probabilistic Safety Assessment (PSA) from those where timing and order of events determine process evolution and eventually violation of safety criteria. The efficiency of the approach has been verified with application to the SARNET benchmark exercise on the effectiveness of hydrogen management in the containment.

Description: The analytical/deterministic modelling and simulation/probabilistic methods are used separately as a rule in order to analyse the physical processes and random or uncertain events. However, in the currently used probabilistic safety assessment this is an issue. The lack of treatment of dynamic interactions between the physical processes on one hand and random events on the other hand causes the limited assessment. In general, there are a lot of mathematical modelling theories, which can be used separately or integrated in order to extend possibilities of modelling and analysis. The Theory of Probabilistic Dynamics (TPD) and its augmented version based on the concept of stimulus and delay are introduced for the dynamic reliability modelling and the simulation of accidents in hybrid (continuous-discrete) systems considering uncertain events. An approach of non-Markovian simulation and uncertainty analysis is discussed in order to adapt the Stimulus-Driven TPD for practical applications. The developed approach and related methods are used as a basis for a test case simulation in view of various methods applications for severe accident scenario simulation and uncertainty analysis. For this and for wider analysis of accident sequences the initial test case specification is then extended and discussed. Finally, it is concluded that enhancing the modelling of stimulated dynamics with uncertainty and sensitivity analysis allows the detailed simulation of complex system characteristics and representation of their uncertainty. The developed approach of accident modelling and analysis can be efficiently used to estimate the reliability of hybrid systems and at the same time to analyze and possibly decrease the uncertainty of this estimate.

Description: The colocated dual-polarized dipole (DPD) and dual-polarized loop (DPL) MIMO channel performances are compared. Computation results show that, for the ideal electric and magnetic dipoles, the dual-polarized MIMO systems have identical channel capacity. But the contour plots of the capacity gain of the realistic DPD and DPL are different, due to the difference in antenna patterns. The cumulative distribution function (CDF) of the capacity gain in the two-mirror (TM) channel shows that, for small distance, the capacity gain obtained by the DPD is obviously smaller than that of the DPL, but, with the increase of the distance, the difference gets smaller. A DPL with low mutual coupling is fabricated. Measured results show that high MIMO capacities can be obtained by this DPL in both the anechoic chamber (AC) and the realistic office room. The capacity gain of the DPL antenna is 1.5–1.99, which basically coincides with the theoretical and numerical results. Furthermore, the capacity of the virtual DPL antenna with no mutual couplings is also investigated. It is shown that, in the AC, the mutual coupling will generally decrease the dual-polarized MIMO capacity; however, in the office room, the effect of mutual coupling is not always negative.

Description: The true polarization diversity (TPD) technique is combined with the spatial diversity technique in novel MIMO antenna array geometries with a large number of elements. The use of a large number of elements requires some angular reuse within the array for polarization diversity. With designs compatible with existing base station antenna array configurations, the novel geometries with combining diversity schemes are shown to be able to achieve near the maximum spectral efficiencies. True polarization diversity (TPD) schemes are found to be an excellent complement to more conventional spatial diversity schemes for obtaining optimum MIMO array performance in base station antennas.

Description: Measured propagation loss for capacitive body-coupled communication (BCC) channel (1 MHz to 60 MHz) is limitedly available in the literature for distances longer than 50 cm. This is either because of experimental complexity to isolate the earth-ground or design complexity in realizing a reliable communication link to assess the performance limitations of capacitive BCC channel. Therefore, an alternate efficient full-wave electromagnetic (EM) simulation approach is presented to realistically analyze capacitive BCC, that is, the interaction of capacitive coupler, the human body, and the environment all together. The presented simulation approach is first evaluated for numerical/human body variation uncertainties and then validated with measurement results from literature, followed by the analysis of capacitive BCC channel for twenty different scenarios. The simulation results show that the vertical coupler configuration is less susceptible to physiological variations of underlying tissues compared to the horizontal coupler configuration. The propagation loss is less for arm positions when they are not touching the torso region irrespective of the communication distance. The propagation loss has also been explained for complex scenarios formed by the ground-plane and the material structures (metals or dielectrics) with the human body. The estimated propagation loss has been used to investigate the link-budget requirement for designing capacitive BCC system in CMOS sub-micron technologies.

Description: A novel compressive sensing- (CS-) based direction-of-arrival (DOA) estimation algorithm is proposed to solve the performance degradation of the CS-based DOA estimation in the presence of sensing matrix mismatching. Firstly, a DOA sparse sensing model is set up in the presence of sensing matrix mismatching. Secondly, combining the Dantzig selector (DS) algorithm and least-absolute shrinkage and selection operator (LASSO) algorithm, a CS-based DOA estimation algorithm which performs iterative optimization alternatively on target angle information vector and sensing matrix mismatching error vector is proposed. The simulation result indicates that the proposed algorithm possesses higher angle resolution and estimation accuracy compared with conventional CS-based DOA estimation algorithms.

Description: A novel miniaturized 1 × 10 uniform linear dual slant-polarized UWB antenna array for MIMO base station is presented. The antenna array operates in the frequency band from 1710 to 2690 MHz with a 17.3–18.7 dBi gain in a size of 105 × 1100 × 37 mm. The array element is composed of two single-polarized dipoles evolved from bow-tie antenna with slots on them, which miniaturize the size of the antenna. The 10 array elements are fed through an air dielectric strip-line power splitter. Two parameters, the beam tracking and the beam squint, are presented to quantitatively describe the pattern symmetry property of the antenna. The simulated and measured radiation performances are studied and compared. The results show that the pattern symmetry property of the single antenna element has been improved about 24% compared with the former study, and the antenna array also provides excellent pattern symmetry property.

Description: The paper introduces a novel method for agile and precise wireless power transmission operated by a time-modulated array. The unique, almost real-time reconfiguration capability of these arrays is fully exploited by a two-step procedure: first, a two-element time-modulated subarray is used for localization of tagged sensors to be energized; the entire 16-element TMA then provides the power to the detected tags, by exploiting the fundamental and first-sideband harmonic radiation. An investigation on the best array architecture is carried out, showing the importance of the adopted nonlinear/full-wave computer-aided-design platform. Very promising simulated energy transfer performance of the entire nonlinear radiating system is demonstrated.

Description: In integrated deterministic and probabilistic safety analysis (IDPSA), safe scenarios and prime implicants (PIs) are generated by simulation. In this paper, we propose a novel postprocessing method, which resorts to a risk-based clustering method for identifying Near Misses among the safe scenarios. This is important because the possibility of recovering these combinations of failures within a tolerable grace time allows avoiding deviations to accident and, thus, reducing the downtime (and the risk) of the system. The postprocessing risk-significant features for the clustering are extracted from the following: (i) the probability of a scenario to develop into an accidental scenario, (ii) the severity of the consequences that the developing scenario would cause to the system, and (iii) the combination of (i) and (ii) into the overall risk of the developing scenario. The optimal selection of the extracted features is done by a wrapper approach, whereby a modified binary differential evolution (MBDE) embeds a -means clustering algorithm. The characteristics of the Near Misses scenarios are identified solving a multiobjective optimization problem, using the Hamming distance as a measure of similarity. The feasibility of the analysis is shown with respect to fault scenarios in a dynamic steam generator (SG) of a nuclear power plant (NPP).

Description: System codes for simulation of safety performance of nuclear plants may contain parameters whose values are not known very accurately. New information from tests or operating experience is incorporated into safety codes by a process known as calibration, which reduces uncertainty in the output of the code and thereby improves its support for decision-making. The work reported here implements several improvements on classic calibration techniques afforded by modern analysis techniques. The key innovation has come from development of code surrogate model (or code emulator) construction and prediction algorithms. Use of a fast emulator makes the calibration processes used here with Markov Chain Monte Carlo (MCMC) sampling feasible. This work uses Gaussian Process (GP) based emulators, which have been used previously to emulate computer codes in the nuclear field. The present work describes the formulation of an emulator that incorporates GPs into a factor analysis-type or pattern recognition-type model. This “function factorization” Gaussian Process (FFGP) model allows overcoming limitations present in standard GP emulators, thereby improving both accuracy and speed of the emulator-based calibration process. Calibration of a friction-factor example using a Method of Manufactured Solution is performed to illustrate key properties of the FFGP based process.

Description: This paper presents a theoretical analysis for the accuracy requirements of the planar polarimetric phased array radar (PPPAR) in meteorological applications. Among many factors that contribute to the polarimetric biases, four factors are considered and analyzed in this study, namely, the polarization distortion due to the intrinsic limitation of a dual-polarized antenna element, the antenna pattern measurement error, the entire array patterns, and the imperfect horizontal and vertical channels. Two operation modes, the alternately transmitting and simultaneously receiving (ATSR) mode and the simultaneously transmitting and simultaneously receiving (STSR) mode, are discussed. For each mode, the polarimetric biases are formulated. As the STSR mode with orthogonal waveforms is similar to the ATSR mode, the analysis is mainly focused on the ATSR mode and the impacts of the bias sources on the measurement of polarimetric variables are investigated through Monte Carlo simulations. Some insights of the accuracy requirements are obtained and summarized.

Description: A dual circularly polarized (CP) omnidirectional antenna based on slot array in coaxial cylinder structure is presented in this paper. It is constructed by perpendicular slot pairs around and along the axis of the coaxial cylinder to realize the omnidirectional CP property, and two ports are assigned in its two sides as left hand circularly polarized (LHCP) port and right hand circularly polarized (RHCP) port, respectively. The proposed antenna achieves a bandwidth of 16.4% ranging from 5.05 to 5.95 GHz with an isolation higher than 15 dB between the two CP ports, and the return loss (RL) is higher than 10 dB within the bandwidth in both of the two ports. From the measured results, the average axial ratio (AR) of the proposed antenna in omnidirectional plane is lower than 1.5 dB.

Description: Although the uniform theory of diffraction (UTD) could be theoretically applied to arbitrarilyshaped convex objects modeled by nonuniform rational B-splines (NURBS), one of the great challenges in calculation of the UTD surface diffracted fields is the difficulty in determining the geodesic paths along which the creeping waves propagate on arbitrarilyshaped NURBS surfaces. In differential geometry, geodesic paths satisfy geodesic differential equation (GDE). Hence, in this paper, a general and efficient adaptive variable step Euler method is introduced for solving the GDE on arbitrarilyshaped NURBS surfaces. In contrast with conventional Euler method, the proposed method employs a shape factor (SF) to efficiently enhance the accuracy of tracing and extends the application of UTD for practical engineering. The validity and usefulness of the algorithm can be verified by the numerical results.

Description: A wideband dual-polarized antenna for WLAN, WiMAX, and LTE base station applications is presented in this paper. The proposed antenna consists of two pairs of orthogonal planar quasi-open-sleeve dipoles along the centerlines, a balanced feeding structure and a square ground plane. The planar quasi-open-sleeve dipole comprises a pair of bowtie-shaped planar dipoles with two parallel curve parasitic elements. The introduced parallel curve parasitic elements change the path of the current of the original bowtie-shaped planar dipoles at high frequencies and hence wideband characteristic is achieved. Two pairs of the planar quasi-open-sleeve dipoles placed orthogonally further broaden the bandwidth of the antenna with dual-polarization characteristics. The proposed antenna achieves a 10-dB return loss bandwidth from 2.32 to 4.03 GHz (53.9% bandwidth) using the planar quasi-open-sleeve dipole structures. The isolation between the two ports remains more than 32 dB in the whole bandwidth. Measured results show that the proposed antenna keeps the cross-polarization under −33 dB and the front-to-back ratio better than 15 dB in the operating band. The antenna has an area of 0.3λ  × 0.3λ at 2.32 GHz making it easy to be extended to an array element.

Description: Wave propagation along a closely spaced folded cylindrical helix (FCH) array is investigated for the purpose of designing compact array for energy transport and antenna radiation. It is found that the height of this surface wave guiding structure can be decreased from 0.24 to 0.06 by replacing the monopole element with the FCH. Both the propagation constant and the mode distribution of the dominant wave mechanism are extracted by ESPRIT algorithm, which indicates that a backward propagating surface wave is supported by the array structure. A compact backfire FCH antenna array is designed and measured based on the identified dominant wave mechanism.

Description: This work presents a review on the concept of harmonic or secondary radar, where a tag or transponder is used to respond at a harmonic multiple of the incoming interrogation signal. In harmonic radar, the tag is called a harmonic transponder and the necessary frequency multiplication is implemented using a nonlinear element, such as a Schottky diode. Different applications and operating frequencies of harmonic transponders are presented, along with various tag design aspects. The designer may have to deal with certain tradeoffs during the design with respect to a number of transponder properties, and the role of these tradeoffs is also considered. Additionally, techniques usable for characterization of harmonic transponders are discussed.

Description: Sidelobe level suppression is a major problem in circular array antenna (CAA) synthesis. Many conventional numerical techniques are proposed to achieve this which are time consuming and often fail to handle multimodal problems. In this paper, a method of circular array synthesis using nature inspired flower pollination algorithm (FPA) is proposed. The synthesis technique considered here adapts one and two degrees of freedom, namely, amplitude only and amplitude spacing. The effectiveness of the FPA is studied by comparing the results with genetic algorithm (GA) and uniform circular array antenna (UCAA) with uniform spacing. Also the effect of additional degree of freedom on the aperture size and the computational time is analyzed. A relative side lobe level (SLL) of −25 dB is achieved using the algorithm under both no beam scanning (0°) and beam scanning (15°) conditions for 20 and 40 elements of CAA.

Description: This paper presents the results of the analysis of the Unprotected Loss of Flow (ULOF) experiment SHRT-45R performed in the EBR-II fast reactor. These experiments are being analyzed in the scope of a benchmark exercise coordinated by the IAEA. The SHRT-45R benchmark contains a neutronic and a thermal-hydraulic part and results are presented for both. Neutronic calculations are performed with the ERANOS2.0 code in combination with various sets of nuclear data. The thermal-hydraulic evaluation is done with RELAP5-3D. The results are that the major neutronic parameters are well predicted with error margins on the order of 1%. The thermal-hydraulic results are less favourable: a consistent overestimation of the outlet temperature occurs in combination with erroneous flow distribution. Observed differences with measured data cannot be explained easily. The work presented in this paper was undertaken to investigate and validate the effectiveness of the calculational tools and data that are commonly used in our lab for the design and analysis of liquid metal cooled fast reactors.

Description: Capacity of a wireless link can be enhanced by increasing the number of receive antennas. However, imposed receiver physical size constraints necessitate that the antenna elements be in close proximity, which typically reduces the overall link capacity of the wireless channel. Counterintuitively, under certain conditions the capacity of the overall link can be enhanced by decreasing antenna spacings. The focus of this paper is that of identifying the fundamental mechanisms and the conditions that give rise to this excess capacity. Closed-form expressions that directly quantify this capacity gain are derived based on a representative circuit theoretic model. Interesting insights are developed about the impact of different noise and interference sources and the limiting effect of heat losses in the antenna system. The capacity analysis is subsequently generalized to encompass the effect of antenna current deformation and load mismatch due to mutual coupling, based on the standard Method of Moments (MoM) analysis, demonstrating similar capacity enhancement behavior as predicted by the closed-form expressions.

Description: Fractal patch antennas based on the Sierpinski structure are studied in this paper. The antennas operate at dual bands (around 2 and 5 GHz) and are designed to steer the beam directions at around 5 GHz band (the first harmonic). The antennas use reconfigurable triple feeds on the same antenna plane to have three beam directions. The same scale factor defines the geometrical self-similarity of the Sierpinski fractal. The proposed antennas are fabricated through three iterations from 1st order to 3rd order and utilize FR-4 (εr = 4.4) for the microwave substrate. The performances of the antennas, such as reflection coefficients and radiation patterns are verified by simulation and measurement. The results show that the properties of the proposed antennas in three orders are similar.

Description: A triband MIMO antenna used for gsm1800/td-scdma/lte/wi-max/wiLan/wifi has been proposed in this paper. The design with the size of 32 m 73.6 mm is fabricated on FR4 substrate (thickness is 1.6 mm). This antenna consists of two reversed monopole meandered radiators and defected ground structure which work together to achieve impedance match and enhance isolation for all operating bands. According to the subsequent measured results, the working frequency domains are at gsm1800 (1.71 GHz–1.88 GHz), td-scdma (1.88 GHz–2.025 GHz), lte (2.1–2.35, 2.48–2.51), wi-max (3.5 GHz, 5.5 GHz), wiLan (5.725 GHz–5.8 GHz), and wifi (5.8 GHz–5.88 GHz) approximately. Besides, the measured radiation patterns (gain total) are also well at these working frequency domains and the omnidirectional performance has been achieved for the reversed MIMO antenna array. Furthermore, the realized isolation is more than 15 dB, 24.2 dB, and 22 dB at the first, the second, and the third working frequency band, respectively.

Description: A compact circular polarized antenna array with a convenient gain/bandwidth/dimension trade-off is proposed for applications in the C-band. The design is based on the recursive application of the sequential phase architecture, resulting in a 4 × 4 array of closely packed identical antennas. The 16 antenna elements are disc-based patches operating in modal degeneration, tuned to exhibit a broad while imperfect polarization. Exploiting the compact dimension of the patches and a space-filling design for the feeding network, the entire array is designed to minimize the occupied area. A prototype of the proposed array is fabricated with standard photoetching procedure in a single-layer via less printed board of overall area 80 × 80 mm2. Adequate left-hand polarization is observed over a wide bandwidth, demonstrating a convenient trade-off between bandwidth and axial ratio. Satisfying experimental results validate the proposed design, with a peak gain of 12.6 dB at 6.7 GHz maintained within 3 dB for 1 GHz, a very wide 10 dB return loss bandwidth of 3 GHz, and a 4 dB axial ratio bandwidth of 1.82 GHz, meaning 31% of fractional bandwidth.

Description: A new algorithm for improving Direction of Arrival Estimation (DOAE) accuracy has been carried out. Two contributions are introduced. First, Doppler frequency shift that resulted from the target movement is estimated using the displacement invariance technique (DIT). Second, the effect of Doppler frequency is modeled and incorporated into ESPRIT algorithm in order to increase the estimation accuracy. It is worth mentioning that the subspace approach has been employed into ESPRIT and DIT methods to reduce the computational complexity and the model’s nonlinearity effect. The DOAE accuracy has been verified by closed-form Cramér-Rao bound (CRB). The simulation results of the proposed algorithm are better than those of the previous estimation techniques leading to the estimator performance enhancement.

Description: The design and simulation of a 10 × 8 multibeam dual-band orthogonal linearly polarized antenna array operating at Ku-band are presented for transmit-receive applications. By using patches with different coupling methods as elements, both perpendicular polarization in 12.25–12.75 GHz band and horizontal polarization in 14.0–14.5 GHz band are realized in a shared antenna aperture. A microstrip Rotman lens is employed as the beamforming network with 7 input ports, which can generate a corresponding number of beams to cover −30°–30° with 5 dB beamwidth along one dimension. This type of multibeam orthogonal linearly polarized planar antenna is a good candidate for satellite communication (SatCom).

Description: As the available space in the board of a mobile device becomes smaller and more compact, circuit elements and transmission lines are arranged in very close proximity, especially from the antennas which are usually installed on the same board. Due to the various on-board antennas which are designed in small space, the transmission lines on the board are electromagnetically interfered, resulting in the performance degradation of the circuit. So the engineers and circuit designers should find the least interfered place for the transmission lines and components to minimize the electromagnetic interferences. This paper discusses and presents a methodology to find the least sensitive position in the induced current distribution as well as in the noise power delivered from the antenna. For this purpose some vertical, horizontal, and bent transmission lines with antenna on the same board are designed and fabricated with and without common ground, and the transferred powers to the transmission lines were measured and were also simulated using a full-wave simulator. The results predicted by the EM simulation model were successfully confirmed through the measurement of S-parameters in the experimental setup, which shows the validness of the suggested analysis method.

Description: This paper reports two numerical simulation methods for modeling displacement instabilities around a surface groove in a metal substrate used in nuclear power plant. The amplitude change in the groove, the downward displacement at the base node, and the groove displacement at the periphery were simulated using ABAQUS to compare the results from two methods, as well as the tangential stress in the elements at the groove base and periphery. The comparison showed that for the tangential stress two methods were in close agreement for all thermal cycles. For the amplitude change, the downward displacement, the groove displacement, and the stress distribution, the two methods were in close agreement for the first 3 to 6 thermal cycles. After that, inconsistency increased with the number of thermal cycles. It is interesting that the thermal cycle at which the discrepancy between the two methods began to occur corresponded to a thermally grown oxide (TGO) thickness of 1 μm, which showed the accuracy of the present work over the classic method. It is concluded that the present work’s numerical simulation scheme worked better with a thinner TGO layer than the classic method and could overcome the limitation of TGO thickness by simulating any thickness.

Description: The first- and second-order bistatic high frequency radar cross sections of the ocean surface with an antenna on a floating platform are derived for a frequency-modulated continuous wave (FMCW) source. Based on previous work, the derivation begins with the general bistatic electric field in the frequency domain for the case of a floating antenna. Demodulation and range transformation are used to obtain the range information, distinguishing the process from that used for a pulsed radar. After Fourier-transforming the autocorrelation and comparing the result with the radar range equation, the radar cross sections are derived. The new first- and second-order antenna-motion-incorporated bistatic radar cross section models for an FMCW source are simulated and compared with those for a pulsed source. Results show that, for the same radar operating parameters, the first-order radar cross section for the FMCW waveform is a little lower than that for a pulsed source. The second-order radar cross section for the FMCW waveform reduces to that for the pulsed waveform when the scattering patch limit approaches infinity. The effect of platform motion on the radar cross sections for an FMCW waveform is investigated for a variety of sea states and operating frequencies and, in general, is found to be similar to that for a pulsed waveform.

Description: Instrumental neutron activation analysis (INAA) is a powerful technique for trace element determination in rocks. Nine alabaster samples were collected from Wadi El-Nakhil located at the intersection of lat. 26°10′50′′N and long. 34°03′40′′E, central Eastern Desert, Egypt, for investigation by INAA and Energy Depressive X-Ray Fluorescence (EDXRF). The samples were irradiated by thermal neutrons at the TRIGA Mainz research reactor at a neutron flux of 7 × 1011 n/cm2·s. Twenty-two elements were determined, namely, As, Ba, Ca, Co, Cr, Sc, Fe, Hf, K, Mg, Mn, Na, Rb, U, Zn, Zr, Lu, Ce, Sm, La, Yb, and Eu. The chemical analysis of alabaster indicated having high contents of CaO and MgO and LOI and low contents of SiO2, Al2O3, Na2O, K2O, MnO, and Fe2O3.

Description: This paper reports the results of sensitivity analysis of the multidimension, multigroup neutron diffusion NODAL3 code for the NEACRP 3D LWR core transient benchmarks (PWR). The code input parameters covered in the sensitivity analysis are the radial and axial node sizes (the number of radial node per fuel assembly and the number of axial layers), heat conduction node size in the fuel pellet and cladding, and the maximum time step. The output parameters considered in this analysis followed the above-mentioned core transient benchmarks, that is, power peak, time of power peak, power, averaged Doppler temperature, maximum fuel centerline temperature, and coolant outlet temperature at the end of simulation (5 s). The sensitivity analysis results showed that the radial node size and maximum time step give a significant effect on the transient parameters, especially the time of power peak, for the HZP and HFP conditions. The number of ring divisions for fuel pellet and cladding gives negligible effect on the transient solutions. For productive work of the PWR transient analysis, based on the present sensitivity analysis results, we recommend NODAL3 users to use radial nodes per assembly, axial layers per assembly, the maximum time step of 10 ms, and 9 and 1 ring divisions for fuel pellet and cladding, respectively.

Description: The detection and identification of ship targets navigating in coastal areas are essential in order to prevent maritime accidents and to take countermeasures against illegal activities. Usually, coastal radar systems are employed for the detection of vessels, whereas noncooperative ship targets as well as ships not equipped with AIS transponders can be identified by means of dedicated active radar imaging system by means of ISAR processing. In this work, we define a parasitic array receiver for ISAR imaging purposes based on the signal transmitted by an opportunistic coastal radar over its successive scans. In order to obtain the proper cross-range resolution, the physical aperture provided by the array is combined with the synthetic aperture provided by the target motion. By properly designing the array of passive devices, the system is able to correctly observe the signal reflected from the ships over successive scans of the coastal radar. Specifically, the upper bounded interelement spacing provides a correct angular sampling accordingly to the Nyquist theorem and the lower bounded number of elements of the array ensures the continuity of the observation during multiple scans. An ad hoc focusing technique has been then proposed to provide the ISAR images of the ships. Simulated analysis proved the effectiveness of the proposed system to provide top-view images of ship targets suitable for ATR procedures.

Description: The increase in global navigation satellite systems (GNSS) availability and services is fostering a new wave of applications related to satellite navigation. Such increase is also followed by more and more threats, aiming at signal disruption. In order to fully exploit the potentialities of precise and reliable navigation, being able at the same time to counteract threats such as interference, jamming, and spoofing, smart antenna systems are being investigated worldwide, with the requirements of multiband operation and compactness. In order to answer such need, the present work proposes a miniaturized dielectric resonator antenna (DRA) 2 × 2 array able to operate at E5/L5, L2, and E6 bands, with an overall footprint of only 3.5′′ (89 mm).

Description: A wideband slot antenna for mobile phone applications is proposed. The antenna has two slots with open ends etched on the opposite edges of the ground plane. The main slot, of total length of 59 mm, is composed of a rectangle connected to a circle having radius of 5 mm. Another slot, having a rectangular shape with width of 2.8 mm and length of 26 mm, is employed to enhance the antenna bandwidth. The slots are fed by means of a rectangular monopole connected to a circular patch joined to a bent 50 Ω microstrip transmission line forming two right angles. To obtain a wideband impedance matching, the upper edge of the monopole and a part of the feeding line evolve along the top edge of the two slots. To reduce the antenna size, the upper part of the board above the slot (just 3 mm from the slot) is folded vertically to the ground plane. The measured bandwidth of the antenna is 0.698–1.10 GHz and 1.64–2.83 GHz covering LTE700/2300/2500, GSM850/900/1800/1900, and UMTS bands.

Description: The double-ended guillotine break (DEGB) of the horizontal coaxial gas duct accident is a serious air ingress accident of the high temperature gas-cooled reactor pebble-bed module (HTR-PM). Because the graphite is widely used as the structure material and the fuel element matrix of HTR-PM, the oxidation analyses of this severe air ingress accident have got enough attention in the safety analyses of the HTR-PM. The DEGB of the horizontal coaxial gas duct accident is calculated by using the TINTE code in this paper. The results show that the maximum local oxidation of the matrix graphite of spherical fuel elements in the core will firstly reach  mol/m3 at about 120 h, which means that only the outer 5 mm fuel-free zone of matrix graphite will be oxidized out. Even at 150 h, the maximum local weight loss ratio of the nuclear grade graphite in the bottom reflectors is only 0.26. Besides, there is enough time to carry out some countermeasures to stop the air ingress during several days. Therefore, the nuclear grade graphite of the bottom reflectors will not be fractured in the DEGB of the horizontal coaxial gas duct accident and the integrity of the HTR-PM can be guaranteed.

Description: An approximation mathematical formula to compute the distorted radiation pattern for reflector antennas is presented. In this approximation formula, besides the phase error caused by the structural deformation being added in the far field integral, the surface normal vector variation is also taken into consideration. The formula is derived by expanding the surface normal vector into a first-order Taylor series and the phase error into a second-order Taylor series. By assembling the integrals including the contributions of both surface normal vector variation and phase error, the far field electrical vector expressed as a function of structural nodal displacements is further obtained in a matrix form. Simulation results of a distorted reflector show the application of this formula.

Description: The significant wave height (SWH) retrieved from collocated HH and VV polarized X-band marine radars under different sea states is studied. The SWH are retrieved from different principal components of X-band marine radar image sequence. As compared with the SWH measured by a buoy, the root-mean-square errors of the SWH are 0.32–0.45 m for VV polarization, and they are 0.37–0.60 m for HH polarization. At the wind speeds of 0–5 m/s, the SWH can be derived from VV polarized radar images, while the backscatter of HH polarized radar is too weak to contain wave signals at very low wind speeds (~0–3 m/s). At the wind speeds of 5–18 m/s, the SWH retrieved from VV polarization coincide well with the SWH measured by the buoy, while the SWH retrieved from HH polarization correspond with the changes of the wind speed. At the wind speeds of 18–26 m/s, the influence of wave breaking on HH polarization is more important than that on VV polarization. This indicates that the imaging mechanisms of HH polarized X-band marine radar are different from those of VV polarized X-band marine radar.

Description: Gamma-ray measurements in various research fields require efficient detectors. One of these research fields is mass attenuation coefficients of different materials. Apart from experimental studies, the Monte Carlo (MC) method has become one of the most popular tools in detector studies. An NaI(Tl) detector has been modeled, and, for a validation study of the modeled NaI(Tl) detector, the absolute efficiency of 3 × 3 inch cylindrical NaI(Tl) detector has been calculated by using the general purpose Monte Carlo code MCNP-X (version 2.4.0) and compared with previous studies in literature in the range of 661–2620 keV. In the present work, the applicability of MCNP-X Monte Carlo code for mass attenuation of concrete sample material as building material at photon energies 59.5 keV, 80 keV, 356 keV, 661.6 keV, 1173.2 keV, and 1332.5 keV has been tested by using validated NaI(Tl) detector. The mass attenuation coefficients of concrete sample have been calculated. The calculated results agreed well with experimental and some other theoretical results. The results specify that this process can be followed to determine the data on the attenuation of gamma-rays with other required energies in other materials or in new complex materials. It can be concluded that data from Monte Carlo is a strong tool not only for efficiency studies but also for mass attenuation coefficients calculations.

Description: Printed circuit antennas have been used for the detection of electromagnetic radiation at a wide range of frequencies that go from radio frequencies (RF) up to optical frequencies. The design of printed antennas at optical frequencies has been done by using design rules derived from the radio frequency domain which do not take into account the dispersion of material parameters at optical frequencies. This can make traditional RF antenna design not suitable for optical antenna design. This work presents the results of using a genetic algorithm (GA) for obtaining an optimized geometry (unconventional geometries) that may be used as optical regime antennas to capture electromagnetic waves. The radiation patterns and optical properties of the GA generated geometries were compared with the conventional dipole geometry. The characterizations were conducted via finite element method (FEM) computational simulations.

Description: Considering dangerous environmental conditions, maintenance of radioactive equipment can be performed by remote handling maintenance (RHM) system. The RHM system is a sophisticated man-machine system. Therefore, human factors analysis is an inevitable aspect considered in guaranteeing successful and safe task performance. This study proposes an approach for integrated analysis of human factors in RHM so as to make the evaluating process more practical. In the approach, indicators of accessibility, health safety, and fatigue are analyzed using virtual human simulation technologies. The human error factors in the maintenance process are analyzed using the human error probability (HEP) based on the success likelihood index method- (SLIM-) analytic hierarchy process (AHP). The psychological factors level of maintenance personnel is determined with an expert scoring. The human factors for the entire RHM system are then evaluated using the interval method. An application example is present, and the application results show that the approach can support the evaluation of the human factors in RHM.

Description: Based on the special application of 90-degree elbow pipe in the HTR-PM, the large eddy simulation was selected to calculate the instantaneous flow field in the 90-degree elbow pipe combining with the experimental results. The characteristics of the instantaneous turbulent flow field under the influence of flow separation and secondary flow were studied by analyzing the instantaneous pressure information at specific monitoring points and the instantaneous velocity field on the cross section of the elbow. The pattern and the intensity of the Dean vortex and the small scale eddies change over time and induce the asymmetry of the flow field. The turbulent disturbance upstream and the flow separation near the intrados couple with the vortexes of various scales. Energy is transferred from large scale eddies to small scale eddies and dissipated by the viscous stress in the end.

Description: Radio wave propagation in confined spaces is consequent upon the reflections of boundaries; thus, the radiation characteristics of the antenna have significant influence on the field coverage in the confined space. This paper investigates the effects of antenna parameters on field coverage characteristics in a tunnel environment. A modified modal method is proposed to analyse the wave propagation properties along the tunnel. The relationships between the amplitudes of modes and the antenna parameters, including the beam width, beam direction, and antenna location, are analysed. The results indicate that by properly selecting the antenna parameters, optimum field coverage in tunnel environments can be realized.

Description: The analysis and design of a small planar multiband antenna operating in the 4G frequency bands are presented. The numerical and experimental results demonstrated that the proposed antenna satisfies the requirement of 6 dB return loss for the impedance bandwidth of the LTE700/LTE2300/LTE2500 and WiMAX3500 bands. The gains at 750 MHz/2.3 GHz/2.6 GHz/3.5 GHz are 2.1 dBi/4.9 dBi/4.7 dBi/4.3 dBi, respectively. The measured radiation patterns verify the suitability of the antenna to be employed in mobile phones. The dimensions of the radiant patch are 49 × 10 mm2. The proposed antenna can be easily fabricated and customized to various 4G mobile phones as a compact internal antenna.

Description: Korea Atomic Energy Research Institute (KAERI) started the experimental research on moderator circulation as one of a the national research and development programs from 2012. This research program includes the construction of the moderator circulation test (MCT) facility, production of the validation data for self-reliant computational fluid dynamics (CFD) tools, and development of optical measurement system using the particle image velocimetry (PIV). In the present paper we introduce the scaling analysis performed to extend the scaling criteria suitable for reproducing thermal-hydraulic phenomena in a scaled-down CANDU- (CANada Deuterium Uranium-) 6 moderator tank, a manufacturing status of the 1/4 scale moderator tank. Also, preliminary CFD analysis results for the full-size and scaled-down moderator tanks are carried out to check whether the moderator flow and temperature patterns of both the full-size reactor and scaled-down facility are identical.

Description: A novel millimeter wave coplanar waveguide (CPW) fed Fabry-Perot (F-P) antenna with high gain, broad bandwidth, and low profile is reported. The partially reflective surface (PRS) and the ground form the F-P resonator cavity, which is filled with the same dielectric substrate. A dual rhombic slot loop on the ground acts as the primary feeding antenna, which is fed by the CPW and has broad bandwidth. In order to improve the antenna gain, metal vias are inserted surrounding the F-P cavity. A CPW-to-microstrip transition is designed to measure the performances of the antenna and extend the applications. The measured impedance bandwidth of less than −10 dB is from 34 to 37.7 GHz (10.5%), and the gain is 15.4 dBi at the center frequency of 35 GHz with a 3 dB gain bandwidth of 7.1%. This performance of the antenna shows a tradeoff among gain, bandwidth, and profile.

Description: In recent works thinned arrays giving minimum peak sidelobe levels for planar square antenna arrays are obtained using Hadamard difference sets. In the current work thinned array configurations giving lower peak sidelobe levels than those given in the literature are obtained for square arrays of , , , and elements. Differential evolution algorithm is used in the determination of the antenna locations.

Description: A novel dual-band printed end-fired antenna with double-sided parallel-strip line (DSPSL) feeding is presented. The DSPSL acts in wideband transition using balanced transmission. Two different modes of the parasitic patches allow the antenna to work in different bands. The printed antenna is designed as a quasi-Yagi structure to achieve directivity in the lower band, and the parallel rectangular patches serve as the parasitic director. These patches act as radiation patches with end-fire direction characteristics in the upper band. The measured bandwidths were 18.3% for the lower frequency band (2.28–2.74 GHz) and 12.6% for the upper frequency band (5.46–6.2 GHz).

Description: A novel compact dual-polarized antenna is proposed. The antenna has a 1.43% impedance bandwidth which is from 1801 MHz to 1827 MHz for return loss larger than 10 dB. The isolation between the two ports is above 28 dB in the bandwidth, and the gain is 6.6 dBi. The proposed antenna not only consists of a full-planar structure, but also is easy to be fabricated for its simple structure. Additionally, a section of slots and slits is cut on the radiation patch to reduce the area of it to 54% compared with the conventional square patch.

Description: Additive deposition of inks with metallic inclusions provides compelling means to embed electronics into versatile structures. The need to integrate electronics into environmentally friendly components and structures increases dramatically together with the increasing popularity of the Internet of Things. We demonstrate a novel brush-painting method for depositing copper oxide and silver inks directly on wood and cardboard substrates and discuss the optimization of the photonic sintering process parameters for both materials. The optimized parameters were utilized to manufacture passive ultra high frequency (UHF) radio frequency identification (RFID) tag antennas. The results from wireless testing show that the RFID tags based on the copper oxide and silver ink antennas on wood substrate are readable from ranges of 8.5 and 11 meters, respectively, and on cardboard substrate from read ranges of 8.5 and 12 meters, respectively. These results are well sufficient for many future wireless applications requiring remote identification with RFID.

Description: The pilot design problem in large-scale multi-input-multioutput orthogonal frequency division multiplexing (MIMO-OFDM) system is investigated from the perspective of compressed sensing (CS). According to the CS theory, the success probability of estimation is dependent on the mutual coherence of the reconstruction matrix. Specifically, the smaller the mutual coherence is, the higher the success probability is. Based on this conclusion, this paper proposes a pilot design algorithm based on alternating projection and obtains a nonorthogonal pilot pattern. Simulation results show that applying the proposed pattern gives the better performance compared to applying conventional orthogonal one in terms of normalized mean square error (NMSE) of the channel estimate. Moreover, the bit error rate (BER) performance of the large-scale MIMO-OFDM system is improved.

Description: A composite Global Positioning System (GPS) patch antenna with a quadrature 3 dB hybrid coupler was designed and implemented for working RHCP and had a broadband axial ratio (AR) bandwidth. We designed two patches as a FR-4 patch and 1.5 mm thickness thin ceramic patch with a quadrature 3 dB hybrid coupler. A CP radiation pattern was achieved, and the AR bandwidth improved by incorporating a quadrature 3 dB hybrid coupler feed structure in a micro-strip patch antenna. SMD by chip elements was applied to the quadrature 3 dB hybrid coupler. For the composite FR-4 and ceramic patch antennas, the VSWR measurement showed a 2 : 1 ratio over the entire design band, and the 3 dB AR bandwidth was 295 and 580 MHz for the FR-4 patch and ceramic patch antennas, respectively. The antenna gains for the composite FR-4 and ceramic patch antennas were measured as 1.36–2.75 and 1.47–2.71 dBi with 15.11–25.3% and 19.25–28.45% efficiency, respectively.

Description: Sensors health monitoring is essentially important for reliable functioning of safety-critical chemical and nuclear power plants. Autoassociative neural network (AANN) based empirical sensor models have widely been reported for sensor calibration monitoring. However, such ill-posed data driven models may result in poor generalization and robustness. To address above-mentioned issues, several regularization heuristics such as training with jitter, weight decay, and cross-validation are suggested in literature. Apart from these regularization heuristics, traditional error gradient based supervised learning algorithms for multilayered AANN models are highly susceptible of being trapped in local optimum. In order to address poor regularization and robust learning issues, here, we propose a denoised autoassociative sensor model (DAASM) based on deep learning framework. Proposed DAASM model comprises multiple hidden layers which are pretrained greedily in an unsupervised fashion under denoising autoencoder architecture. In order to improve robustness, dropout heuristic and domain specific data corruption processes are exercised during unsupervised pretraining phase. The proposed sensor model is trained and tested on sensor data from a PWR type nuclear power plant. Accuracy, autosensitivity, spillover, and sequential probability ratio test (SPRT) based fault detectability metrics are used for performance assessment and comparison with extensively reported five-layer AANN model by Kramer.

Description: It should be noted that the peak sidelobe level (PSLL) significantly influences the performance of the multibeam imaging sonar. Although a great amount of work has been done to suppress the PSLL of the array, one can verify that these methods do not provide optimal results when applied to the case of multiple patterns. In order to suppress the PSLL for multibeam imaging sonar array, a hybrid algorithm of binary particle swarm optimization (BPSO) and convex optimization is proposed in this paper. In this algorithm, the PSLL of multiple patterns is taken as the optimization objective. BPSO is considered as a global optimization algorithm to determine best common elements’ positions and convex optimization is considered as a local optimization algorithm to optimize elements’ weights, which guarantees the complete match of the two factors. At last, simulations are carried out to illustrate the effectiveness of the proposed algorithm in this paper. Results show that, for a sparse semicircular array with multiple patterns, the hybrid algorithm can obtain a lower PSLL compared with existing methods and it consumes less calculation time in comparison with other hybrid algorithms.

Description: Two curved targets are used to explore far-field superconvergence effects arising in numerical solutions of the electric-field and magnetic-field integral equations. Three different orders of basis and testing functions are used to discretize these equations, and three different types of target models (flat facets, quadratic-curved facets, and cubic-curved facets) are employed. Ideal far-field convergence rates are only observed when the model curvature is one degree higher than the basis order.

Description: A novel low-complexity robust adaptive beamforming (RAB) technique is proposed in order to overcome the major drawbacks from which the recent reported RAB algorithms suffer, mainly the high computational cost and the requirement for optimization programs. The proposed algorithm estimates the array steering vector (ASV) using a closed-form formula obtained by a subspace-based method and reconstructs the interference-plus-noise (IPN) covariance matrix by utilizing a sampling progress and employing the covariance matrix taper (CMT) technique. Moreover, the proposed beamformer only requires knowledge of the antenna array geometry and prior information of the probable angular sector in which the actual ASV lies. Simulation results demonstrate the effectiveness and robustness of the proposed algorithm and prove that this algorithm can achieve superior performance over the existing RAB methods.

Description: Due to the fluctuation of the signal-to-noise ratio (SNR) and the single snapshot case in the MIMO HF sky-wave radar system, the accuracy of the online estimation of the mutual coupling coefficients matrix of the uniform rectangle array (URA) might be degraded by the classical approach, especially in the case of low SNR. In this paper, an Online Particle Mean-Shift Approach (OPMA) is proposed, which is to get a relatively more effective estimation of the mutual coupling coefficients matrix with the low SNR. Firstly, the spatial smoothing technique combined with the MUSIC algorithm of URA is introduced for the DOA estimation of the multiple targets in the case of single snapshot which are taken as coherent sources. Then, based on the idea of the particle filter, the online particles with a moderate computational complexity are used to generate some different estimation results. Finally, the mean-shift algorithm is applied to get a more robust estimate of the equivalent mutual coupling coefficients matrix. The simulation results demonstrate the validity of the proposed approach in terms of the success probability, the statistics of bias, and the variance. The proposed approach is more robust and more accurate than the other two approaches.

Description: A combined cycle that combines AWM cycle with a nuclear closed Brayton cycle is proposed to recover the waste heat rejected from the precooler of a nuclear closed Brayton cycle in this paper. The detailed thermodynamic and economic analyses are carried out for the combined cycle. The effects of several important parameters, such as the absorber pressure, the turbine inlet pressure, the turbine inlet temperature, the ammonia mass fraction, and the ambient temperature, are investigated. The combined cycle performance is also optimized based on a multiobjective function. Compared with the closed Brayton cycle, the optimized power output and overall efficiency of the combined cycle are higher by 2.41% and 2.43%, respectively. The optimized LEC of the combined cycle is 0.73% lower than that of the closed Brayton cycle.

Description: The study of the void reactivity variation in innovative BWR fuel assemblies is presented in this paper. The innovative assemblies are loaded with high enrichment fresh UO2 and MOX fuels. UO2 fuel enrichment is increased above existing design limitations for LWR fuels (〉5%). MOX fuel enrichment with fissile Pu content is established to achieve the same burnup level as that of high enrichment UO2 fuel. For the numerical analysis, the TRITON functional module of SCALE 6.1 code with the 238-group ENDF/B-VI cross section data library was applied. The investigation of the void reactivity feedback is performed in the entire 0–100% void fraction range. Higher values of void reactivity coefficient for assembly loaded with MOX fuel are found in comparison with values for assembly loaded with UO2 fuel. Moreover, coefficient values for MOX fuel are positive over 75% void fraction. The variation of the void reactivity coefficient is explained by the results of the decomposition analysis based on four-factor formula and neutron absorption reactions for main isotopes. Additionally, the impact of the moderation enhancement on the void reactivity coefficient was investigated for the innovative assembly with MOX fuel.

Description: This work is about a horizontal electrically small wire antenna located underground, which transmits electromagnetic signals to the ground. To solve this problem, the expressions of the magnetic vector potential and the electric field are derived. Further, a quasi-static situation is considered in the condition of extremely low frequency (ELF) or super low frequency (SLF) to make an approximation on Sommerfeld integral for easy calculation. The method of moments (MOM) is used to solve the current distribution along the antenna surface at different frequencies, which lays a good foundation for obtaining the electric field of the antenna. Then the three components of the electric field along the radial distance at different polar angles on the ground are investigated, as well as the voltage received on the ground. Furthermore, some influence factors of the antenna are analyzed in order to know the operating characteristics of the antenna better. The results indicate that the antenna length and relative permittivity have a positive correlation with the radial component of the electric field magnitude, while the buried depth, frequency, and conductivity have a negative correlation with that. The influence of these factors on electric field is obvious except the relative permittivity.

Description: In Canada, safe operation of CANDU (CANada Deuterium Uranium; it is a registered trademark of Atomic Energy of Canada Limited) reactors is supported by a full-scope program of nuclear safety research and development (R&D) in key technical areas. Key nuclear R&D programs, facilities, and expertise are maintained in order to address the unique features of the CANDU as well as generic technology areas common to CANDU and LWR (light water reactor). This paper presents an overview of the CANDU safety R&D which includes background, drivers, current status, challenges, and future directions. This overview of the Canadian nuclear safety R&D programs includes those currently conducted by the COG (CANDU Owners Group), AECL (Atomic Energy of Canada Limited), Candu Energy Inc., and the CNSC (Canadian Nuclear Safety Commission) and by universities via UNENE (University Network of Excellence in Nuclear Engineering) sponsorship. In particular, the nuclear safety R&D program related to the emerging CANDU ageing issues is discussed. The paper concludes by identifying directions for the future nuclear safety R&D.

Description: Direct power injection (DPI) and bulk current injection (BCI) methods are defined in IEC 62132-3 and IEC 62132-4 as the electromagnetic immunity test method of integrated circuits (IC). The forward power measured at the RF noise generator when the IC malfunctions is used as the measure of immunity level of the IC. However, the actual power that causes failure in ICs is different from forward power measured at the noise source. Power transfer efficiency is used as a measure of power loss of the noise injection path. In this paper, the power transfer efficiencies of DPI and BCI methods are derived and validated experimentally with immunity test setup of a clock divider IC. Power transfer efficiency varies significantly over the frequency range as a function of the test method used and the IC input impedance. For the frequency range of 15 kHz to 1 GHz, power transfer efficiency of the BCI test was constantly higher than that of the DPI test. In the DPI test, power transfer efficiency is particularly low in the lower test frequency range up to 10 MHz. When performing the IC immunity tests following the standards, these characteristics of the test methods need to be considered.

Description: This paper aims at applying a simplified sea surface model into the physical optics (PO) method to accelerate the scattering calculation from 1D time varying sea surface. To reduce the number of the segments and make further improvement on the efficiency of PO method, a simplified sea surface is proposed. In this simplified sea surface, the geometry of long waves is locally approximated by tilted facets that are much longer than the electromagnetic wavelength. The capillary waves are considered to be sinusoidal line superimposing on the long waves. The wavenumber of the sinusoidal waves is supposed to satisfy the resonant condition of Bragg waves which is dominant in all the scattered short wave components. Since the capillary wave is periodical within one facet, an analytical integration of the PO term can be performed. The backscattering coefficient obtained from a simplified sea surface model agrees well with that obtained from a realistic sea surface. The Doppler shifts and width also agree well with the realistic model since the capillary waves are taken into consideration. The good agreements indicate that the simplified model is reasonable and valid in predicting both the scattering coefficients and the Doppler spectra.

Description: We describe a measurement technique to characterize the equivalent isotropically radiated power (EIRP) of electrically large wireless equipment in a compact environment. A modified phase-measurement method was proposed and, thus, the separation of the signal generator and radiating element was not required during the measurement. A Fresnel-to-far-field transformation was used for the fast measurement time in a compact anechoic chamber. An experimental verification of the method was carried out in a compact anechoic chamber, where the source-detector separation was approximately 1/5 of the far-field distance. The measured magnitude and phase pattern exhibited only a small error. The EIRP obtained using a Fresnel-to-far-field transformation was compared with a reference value, and the error was within 0.5 dB.

Description: In through-wall radar imaging (TWRI), ambiguities in wall characteristics including the thickness and the relative permittivity will distort the image and shift the imaged target position. To quickly and accurately estimate the wall parameters, an approach based on a support vector machine (SVM) is proposed. In TWRI problem, the nonlinearity is embodied in the relationship between backscatter data and the wall parameters, which can be obtained through the SVM training process. Measurement results reveal that once the training phase is completed, the technique only needs no more than one second to estimate wall parameters with acceptable errors. Then through-wall images are reconstructed using a back-projection (BP) algorithm by a finite-difference time-domain (FDTD) simulation. Noiseless and noisy measurements are discussed; the simulation results demonstrate that noisy contamination has little influence on the imaging quality. Furthermore, the feasibility and the validity are tested by a more realistic situation. The results show that high-quality and focused images are obtained regardless of the errors in the wall parameter estimates.

Description: The hybrid solvers based on integral equation domain decomposition method (HS-DDM) are developed for modeling of electromagnetic radiation. Based on the philosophy of “divide and conquer,” the IE-DDM divides the original multiscale problem into many closed nonoverlapping subdomains. For adjacent subdomains, the Robin transmission conditions ensure the continuity of currents, so the meshes of different subdomains can be allowed to be nonconformal. It also allows different fast solvers to be used in different subdomains based on the property of different subdomains to reduce the time and memory consumption. Here, the multilevel fast multipole algorithm (MLFMA) and hierarchical (H-) matrices method are combined in the framework of IE-DDM to enhance the capability of IE-DDM and realize efficient solution of multiscale electromagnetic radiating problems. The MLFMA is used to capture propagating wave physics in large, smooth regions, while H-matrices are used to capture evanescent wave physics in small regions which are discretized with dense meshes. Numerical results demonstrate the validity of the HS-DDM.

Description: This paper presents results of investigation on the coherence bandwidth of narrowband radio channels in 430 MHz band. The coherence bandwidth values were estimated from a power delay profile obtained by recording CDMA2000 forward channel signals during real-field measurements in various environments: medium city, flat terrain, and hilly terrain in northern Poland. The results of measurements are compared with characteristic parameters of UHF radio channel models defined for exemplary narrowband digital system from the TETRA standard. In all of the tested environments, the coherence bandwidth values during most of an observation time were much higher than 25 kHz. Therefore, the fading in tested UHF narrowband channels should be classified as flat fading.

Description: The indoor radio channels at 15 GHz are investigated based on measurements. The large- and small-scale fading behaviors as well as the delay dispersion characteristics are discussed. It is found that the large-scale fading, Ricean -factor, and delay spread can be described by log-normal distributions. Furthermore, both autocorrelation and cross correlation properties of the above parameters are analyzed and modeled. These parameters characterize fading and delay behaviors as well as their mutual dependency and can be used as empirical values for future wireless system design and simulation in 15 GHz short-range indoor channels.

Description: The paper assumes that the channel state information (CSI) is available at the receiver and is known partially at the transmitter through a feedback channel. The bit error rate (BER) performance of multiple transmit antenna selection (MTAS) for the multiple-input and single-output (MISO) system with STBC (MTAS/MISO-STBC) will be investigated in detail. Meanwhile, the selection criterion that maximizes the channel Frobenius norm or minimizes the error probability of MTAS/MISO-STBC system is employed. In two cases of erroneous CSI (ECSI) and inerrable CSI (ICSI), wireless channels of the MTAS systems are modeled and their analytical expressions are derived. For the case of ICSI, the exact BER expressions of the Chernoff upper bound (CUB) for both the MISO-STBC system of full complexity and MTAS system are evaluated, respectively. Next, for the ECSI case, a comprehensive analytical expression of BER CUB for the same system is derived in detail. Finally, extensive Monte-Carlo simulations are presented to support and validate our numerical analysis proposed in this paper. Both the simulating results and the numerical results show that MTAS can reduce effectively the effect of the erroneous CSI.

Description: Energy-efficient communications, namely, green communications, has attracted increasing attention due to energy shortage and greenhouse effect. Motivated by this, we consider the uplink energy-efficient resource allocation in multiuser massive multiple-input multiple-output (MIMO) systems. Specifically, we consider that both the number of antenna arrays at the base station (BS) and the transmit data rate at UE are adjusted adaptively to maximize the energy efficiency. Firstly, we demonstrate the existence of a unique resource allocation solution that is globally optimal by exploiting the properties of objective function. Then we develop an iterative algorithm to solve it. By transforming the originally fractional optimization problem into an equivalent subtractive form using the properties of fractional programming, we develop another efficient iterative resource allocation algorithm. Simulation results have validated the effectiveness of the proposed two algorithms and have shown that both algorithms can fast converge to a near-optimal solution in a small number of iterations.

Description: Wireless channels are commonly affected by short-term fading and long-term fading (shadowing). The shadowing effects must be taken into account also when mobility is present in the wireless scenario. Using a composite fading model, the total channel capacity can be studied for a scenario with short-term Rayleigh fading along with shadowing. This work provides quantitative results for these kinds of scenarios with Rayleigh fading and shadowing, considering also multiple-input and multiple-output systems, which have not been previously reported. In addition, the channel capacity has been studied in depth in its relation with the shadowing level, signal to noise ratio, and the number of elements in the multiple-input and multiple-output system. Moreover, the channel performance with shadowing has been compared to the one without it. Furthermore, Rician model with shadowing is studied and its results are reported. In addition, correlated and experimental results are provided. It is identified that the distributed MIMO systems can benefit from shadowing in Rician channels. This advantage has not been reported previously. This type of fading is proposed for massive MIMO by others and our results open the door to emulate massive MIMO on a reverberation chamber.

Description: To minimize the peak sidelobe level (PSLL) of sparse concentric ring arrays, this paper presents an optimization method of grid ring radii of these arrays. The proposed method is based on modified real genetic algorithm (MGA); it makes grid ring radii as optimal variables and makes elements more reasonably distributed on the array aperture. Also, it can improve the PSLL of the sparse concentric ring arrays and can meanwhile control the computational cost. The simulated results confirming the efficiency and the robustness of the algorithm are provided at last.

Description: When a concrete structure is subjected to an impact, the material is subjected to high triaxial compressive stresses. Furthermore, the water saturation ratio in massive concrete structures may reach nearly 100% at the core, whereas the material dries quickly on the skin. The impact response of a massive concrete wall may thus depend on the state of water saturation in the material. This paper presents some triaxial tests performed at a maximum confining pressure of 600 MPa on concrete representative of a nuclear power plant containment building. Experimental results show the concrete constitutive behavior and its dependence on the water saturation ratio. It is observed that as the degree of saturation increases, a decrease in the volumetric strains as well as in the shear strength is observed. The coupled PRM constitutive model does not accurately reproduce the response of concrete specimens observed during the test. The differences between experimental and numerical results can be explained by both the influence of the saturation state of concrete and the effect of deviatoric stresses, which are not accurately taken into account. The PRM model was modified in order to improve the numerical prediction of concrete behavior under high stresses at various saturation states.

Description: The cellphone based localization system for search and rescue in complex high density ruins has attracted a great interest in recent years, where the radio channel characteristics are critical for design and development of such a system. This paper presents a spatial smoothing estimation via rotational invariance technique (SS-ESPRIT) for radio channel characterization of high density ruins. The radio propagations at three typical mobile communication bands (0.9, 1.8, and 2 GHz) are investigated in two different scenarios. Channel parameters, such as arrival time, delays, and complex amplitudes, are statistically analyzed. Furthermore, a channel simulator is built based on these statistics. By comparison analysis of average excess delay and delay spread, the validation results show a good agreement between the measurements and channel modeling results.

Description: An optimal resource allocation strategy for MIMO relay system is considered in simultaneous wireless information and energy transfer network, where two users with multiple antennas communicate with each other assisted by an energy harvesting MIMO relay that gathers energy from the received signal by applying time switching scheme and forwards the received signal by using the harvesting energy. It is focused on the precoder design and resource allocation strategies for the system to allocate the resources among the nodes in decode-and-forward (DF) mode. Specifically, optimal precoder design and energy transfer strategy in MIMO relay channel are firstly proposed. Then, we formulate the resource allocation optimization problem. The closed-form solutions for the time and power allocation are derived. It is revealed that the solution can flexibly allocate the resource for the MIMO relay channel to maximize the sum rate of the system. Simulation results demonstrated that the performance of the proposed algorithm outperforms the traditional fixed method.

Description: Direction of arrival (DOA) estimation is a crucial problem in electronic reconnaissance. A novel broadband DOA estimation method utilizing nested arrays is devised in this paper, which is capable of estimating the frequencies and DOAs of multiple narrowband signals in broadbands, even though they may have different carrier frequencies. The proposed method converts the DOA estimation of multiple signals with different frequencies into the spatial frequency estimation. Then, the DOAs and frequencies are pair matched by sparse recovery. It is possible to significantly increase the degrees of freedom (DOF) with the nested arrays and the number of sources can be more than that of sensor array. In addition, the method can achieve high estimation precision without the two-dimensional search process in frequency and angle domain. The validity of the proposed method is verified by theoretic analysis and simulation results.

Description: A UWB E-plane omnidirectional microwave antenna is designed and fabricated for IEEE 802.11a communication system and microwave magnetron source system as a radiation monitor. A cooptimization method based on particle swarm optimization (PSO) algorithm and FDTD software is presented. The presented PSO algorithm is useful in many industrial microwave applications, such as microwave magnetron design and other techniques with a high power level. The maximum measured relative bandwidth of 65% is achieved for the proposed antenna after a rapid and efficient optimization. Furthermore, the measured antenna polarization purity reaches about 20 dB at the communication C band. The PSO algorithm is a powerful candidate for microwave passive component design.

Description: This paper is dedicated to different experimental validations concerning a novel concept of beam forming and beam steering antenna. The working principle of the antenna is based on the equivalent radiating surface approach and inspired from an electromagnetic band gap antenna. The theoretical aspect and some numerical validations have been already published in the work of Abou Taam et al. (2014). Different electromagnetic behaviors have been demonstrated, such as low mutual coupling, and high gain preservation for high scanning angles values. In this paper, some of these electromagnetic behaviors will be proven experimentally by the means of two different feeding configurations.

Description: A non-cross-fed printed log-periodic antenna is simulated and studied experimentally. To avoid complex feeding with long coaxial line, the non-cross-feeding structure is applied in this antenna. The software CST Microwave Studio is employed to simulate the proposed antenna, and the optimized antenna model is obtained. According to the simulation results, the antenna prototype is produced and measured. Simulation and measured results show that the antenna is with  dB in band of 4.2–9.2 GHz. And the radiation pattern and gain vary steadily in this band, which achieves requirements for wideband antenna. This antenna design can be extended to the design of the antenna integrated in communication circuit.

Description: The ideal lossless symmetrical reciprocal network (ILSRN) is constructed and introduced to resolve the complex interconnections of two arbitrary microwave networks. By inserting the ILSRNs, the complex interconnections can be converted into the standard one-by-one case without changing the characteristics of the previous microwave networks. Based on the algorithm of the generalized cascade scattering matrix, a useful derivation on the excitation coefficients of antenna arrays is firstly proposed with consideration of the coupling effects. And then, the proposed techniques are applied on the microwave circuits and antenna arrays. Firstly, an improved magic-T is optimized, fabricated, and measured. Compared with the existing results, the prototype has a wider bandwidth, lower insertion loss, better return loss, isolation, and imbalances. Secondly, two typical linear waveguide slotted arrays are designed. Both the radiation patterns and scattering parameters at the input ports agree well with the desired goals. Finally, the feeding network of a two-element microstrip antenna array is optimized to decrease the mismatch at the input port, and a good impedance matching is successfully achieved.

Description: A broadband single-feed circularly polarized patch antenna with wide beamwidth is presented. The patch is coupled to four asymmetric cross slots via a microstrip ring with eight matching segments underneath the ground plane, traversing through the arms of the cross slots in a serial manner. And a coupling slice instead of a resistive load is used as matching load of the microstrip ring for higher gain. Furthermore, a metal side wall surrounding the antenna is used to improve the isolation between adjacent elements in an array. Through optimizing the four asymmetric cross slots and eight matching segments, excellent performances are achieved by the proposed antenna, especially for the broadband and wide beamwidth. Measurement results show that the antenna has −10 dB reflection coefficient bandwidth of 29.7%, 3-dB axial-ratio bandwidth of 21.6%, and beamwidth of more than 90°. It can be considered as a good candidate for the element of arrays.

Description: The Lorentz reciprocity theorem enables us to establish that the transmitting and receiving patterns of any antenna are identical, provided some hypotheses on this antenna and the surrounding medium are satisfied. But reciprocity does not mean that the antenna behaves the same in the transmitting and the receiving modes. In this paper, array antennas fed by multiple beam forming networks are discussed, highlighting the possibility to have different values of internal losses in the beam forming network depending on the operation mode. In particular, a mathematical condition is derived for the specific case of a multiple beam forming network with lossless transmitting mode and lossy receiving mode, such a behavior being fully consistent with the reciprocity theorem. A theoretical discussion is provided, starting from a simple 2-element array to a general multiple beam forming network. A more practical example is then given, discussing a specific Nolen matrix design and comparing theoretical aspects with simulation results.

Description: Vector-sensor arrays such as those composed of crossed dipole pairs are used as they can account for a signal’s polarisation in addition to the usual direction of arrival information, hence allowing expanded capacity of the system. The problem of designing fixed beamformers based on such an array, with a quaternionic signal model, is considered in this paper. Firstly, we consider the problem of designing the weight coefficients for a fixed set of vector-sensor locations. This can be achieved by minimising the sidelobe levels while keeping a unitary response for the main lobe. The second problem is then how to find a sparse set of sensor locations which can be efficiently used to implement a fixed beamformer. We propose solving this problem by converting the traditional norm minimisation associated with compressive sensing into a modified norm minimisation which simultaneously minimises all four parts of the quaternionic weight coefficients. Further improvements can be made in terms of sparsity by converting the problem into a series of iteratively solved reweighted minimisations, as well as being able to enforce a minimum spacing between active sensor locations. Design examples are provided to verify the effectiveness of the proposed design methods.

Description: A method for determining the location of Global Systems for Mobile Communications (GSM) mobile transmitters is proposed. Our approach estimates the location of a source without the use of multilateration or Line-of-Sight (LOS) techniques. A Multipath Characteristic Database (MCD) containing the multipath feature vectors, for each possible transmitter location within an area of interest, is populated via ray-tracing software simulations. The multipath characteristics of interest are angle-of-arrival (AOA) (azimuth) and time-of-arrival (TOA). By minimizing the “distance” between estimated and simulated multipath feature vectors, an estimate for the actual source location can be obtained. The development of the estimation method is presented, followed by a detailed analysis of its estimation accuracy. Since the proposed method utilizes a simulated multipath signature database based upon the knowledge of the environment and the terrain, the need for a priori soundings from the area of interest is eliminated, thus making this location estimation system suitable for application in denied territories. Location accuracies compare favorably with the requirements for the location of wireless 9-1-1 callers as recommended by the Federal Communications Commission (FCC).

Description: A wireless charger for low capacity thin-film batteries is presented. The proposed device consists of a nonradiative wireless resonant energy link and a power management unit. Experimental data referring to a prototype operating in the ISM band centered at 434 MHz are presented and discussed. In more detail, in order to facilitate the integration into wearable accessories (such as handbags or suitcases), the prototype of the wireless energy link was implemented by exploiting a magnetic coupling between two planar resonators fabricated by using a conductive fabric on a layer of leather. From experimental data, it is demonstrated that, at 434 MHz, the RF-to-RF power transfer efficiency of the link is approximately 69.3%. As for the performance of the system as a whole, when an RF power of 7.5 dBm is provided at the input port, a total efficiency of about 29.7% is obtained. Finally, experiments performed for calculating the charging time for a low capacity thin-film battery demonstrated that, for RF input power higher than 6 dBm, the time necessary for recharging the battery is lower than 50 minutes.

Description: In sodium-cooled fast reactors (SFR), grid plate is a critical component which is made of 316 L(N) SS. It is supported on core support structure. The grid plate supports the core subassemblies and maintains their verticality. Most of the components of SFR are made of 316 L(N)/304 L(N) SS and they are in contact with the liquid-metal sodium which acts as a coolant. The peak operating temperature in SFR is 550°C. However, the self-welding starts at 500°C. To avoid self-welding and galling, hardfacing of the grid plate has become necessary. Nickel based cobalt-free colmonoy 5 has been identified as the hardfacing material due to its lower dose rate by Plasma Transferred Arc Welding (PTAW). This paper is concerned with the measurement and investigations of the effects of the residual stress generated due to thermal cycling on a scale-down physical model of the grid plate. Finite element analysis of the hardfaced grid plate model is performed for obtaining residual stresses using elastoplastic analysis and hence the results are validated. The effects of the residual stresses due to thermal cycling on the hardfaced grid plate model are studied.

Description: This paper deals with suitable antennas for energy harvesting, which is a growing research field due to the utilization of nowadays ubiquitous and abundant RF energy. Four types of basic antenna structures suitable for harvesting applications, namely, the patch antenna, slot antenna, modified inverted F antenna, and dielectric resonator antenna, are compared from the viewpoint of reflection coefficient, efficiency, radiation patterns, and dimensions. The frequencies of interest were chosen so that they cover several main wireless systems operating between 0.8 GHz and 2.6 GHz, that is, GSM, UMTS, and WiFi.

Description: A method of transforming high-order Gaussian beams (GBs) mode into circular symmetry fundamental Gaussian beam (FGB) mode with arbitrary waist size is presented using irradiance moments method in quasi-optical (QO) mode converters. The double shaped mirrors correcting amplitude and phase simultaneously are generated by a single incidence irradiance sampling data and known ideal output FGB taking advantage of linear moment matching technique and Fresnel diffraction theory, which can be applied to a wide frequency range especially significant for terahertz band. The numerical coding procedure of creating double correcting mirrors and its fast convergence speed are discussed at 325 GHz. Numerical and experimental comparisons reveal the conclusion that enhancing surface precision and increasing moments order can improve main lobe levels.