ALBERT

Description: Upward mining of the residual coal seam over an abandoned pillar working is one of the effective measures to alleviate the contradiction between limited resources and increased consumption. Interburden stability over an abandoned pillar working plays a significant role in guaranteeing the safety of upward mining; however, it has not yet been extensively studied and understood. In this study, the vertical stress of the interburden over an abandoned pillar working was first investigated. The mechanical model of the interburden was established and the damage conditions were analysed. Then, the stability of the interburden over 38502 abandoned workings in Baijiazhuang coal mine was determined by mechanical analysis and field monitoring. The results show that: (i) Vertical stress of the interburden over abandoned mining zones is clearly lower than the initial stress, indicating the existence of a de-stressed effect. Moreover, vertical stress of the interburden over residual coal pillars is greater than the initial stress, which is the evidence of a stress concentration effect. (ii) The interburden over an abandoned pillar working should be regarded as an elastic rectangular plate supported by generalized Kelvin bodies in mechanical modelling. (iii) The interburden over abandoned mining zones may experience two damage stages. In the first stage, initial plastic damage appears at the central region of interburden. In the second stage, the plastic damage evolves from the central point to the surrounding areas. (iv) The mechanical analysis and field monitoring both indicate the initial damage occurred at the central region over 38502 abandoned workings in Baijiazhuang coal mine before upward mining. Related rock control measures should be implemented in that region to guarantee the safe mining of the residual coal seam.

Description: In experimental investigations on axial symmetry, over-ventilated CH 4 /air diffusion combustion in a packed bed is executed to study the height, shape and stability of the flame. The combustor is a quartz tube packed with alumina pellets in which a cylindrical fuel stream is surrounded by a coflow air nozzle. The results show that the bed length and pellet diameter have a significant influence on the flame properties. In general, the flame above the pellet surface has axial symmetry, and its shape and colour are similar to those of a conventional diffusion flame when the bed length is smaller. The colour of the flame front varies with the bed length. The changed colour indicates an increased flame front temperature and that the combustion regime above the bed surface may change from non-premixed combustion to partially premixed combustion or even premixed combustion owing to the mix and dispersion effect in the packed bed. In addition, multiple flame behaviours, such as an inclined flame front, isolated reaction zone and oscillatory motion followed by a pulsating sound with a few hertz in a packed bed, are observed experimentally. The possible reasons for these phenomena are discussed.

Description: Biomass resources have the potential to produce clean-energy. However, their physico-chemical properties are inferior to those of coal, and thus, biomass resources are not regarded as ideal feedstock for industrial application. In the present study, the pyrolysis of corn (maize) straw pellets was performed under different temperatures (400, 450, 500, 550 and 600°C) at a 10°C min –1 heating rate and 30 min residence time, and the characteristics of biochar pellets were carefully investigated, particularly their elemental composition, hydrophobicity and mechanical resistance. Fourier transform infrared, proximate analysis and scanning electron microscopy were performed. Results indicated that the mass and energy yields of the biochar pellets decreased from 35.46 to 28.65% and from 50.17 to 45.52%, respectively, at increased temperature. Meanwhile, the higher heating value of the biochar pellets increased from 15.45 MJ kg –1 in the raw materials to 21.86 and 24.55 MJ kg –1 in the biochar produced at 400 and 600°C, respectively. In addition, biochar pellets showed good hydrophobicity, which benefited their storage and transportation, though mechanical resistance decreased. The pellets had compact structures, regular shapes and weakened or no functional groups in contrast with raw pellets, and these properties played important roles in the improvements.

Description: Electrode material design is the key to the development of asymmetric supercapacitors with high electrochemical performances and stability. In this work, Al-doped NiO nanosheet arrays were synthesized using a facile hydrothermal method followed by a calcination process, and the synthesized arrays exhibited a superior pseudocapacitive performance, including a favourable specific capacitance of 2253 ± 105 F g –1 at a current density of 1 A g –1 , larger than that of an undoped NiO electrode (1538 ± 80 F g –1 ). More importantly, the arrays showed a high-rate capability (75% capacitance retention at 20 A g –1 ) and a high cycling stability (approx. 99% maintained after 5000 cycles). The above efficient capacitive performance benefits from the large electrochemically active area and enhanced conductivity of the arrays. Furthermore, an assembled asymmetric supercapacitor based on the Al-doped NiO arrays and N-doped multiwalled carbon nanotube ones delivered a high specific capacitance of 192 ± 23 F g –1 at 0.4 A g –1 with a high-energy density of 215 ± 15 Wh kg –1 and power density of 21.6 kW kg –1 . Additionally, the asymmetric device exhibited a durable cyclic stability (approx. 100% retention after 5000 cycles). This work with the proposed doping method will be beneficial to the construction of high-performance supercapacitor systems.

Description: Safe production is the foundation of the normal operations of petrochemical enterprises, and it helps maintain social stability. The main purpose of this study is to prevent petrochemical enterprise accidents by proposing a composite safety assessment approach based on the cloud model, preliminary hazard analysis–layer of protection analysis (PHA–LOPA) and the bow-tie model. First, the petrochemical enterprise and its relevant indicators were evaluated based on the cloud model. Second, the quantitative effect of the uncertainty transformation on the evaluation result of the cloud model was further analysed. This mainly includes the error analysis of the numerical characteristics under the conditions of few samples and small values. Third, the critical indicators such as shock and noise can be weakened and prevented by corresponding safety measures based on PHA–LOPA and the bow-tie model. After adopting two independent protection layers, the risk levels of shock and noise decrease from 3 to 2. Then, shock and noise were analysed in depth with the bow-tie model, and the causes and consequences were identified. Moreover, corresponding safety measures were taken to prevent accidents. The case study validated the validity and feasibility of the composite safety assessment approach proposed here.

Description: In this article, we have synthesized a series of nitrogen-doped nanoporous carbon (NPC) from metal organic framework of UiO-66 with different ratios of adenine and 1,4-benzendicarboxylate (H 2 BDC) coated on carbon nanotube film (CNTF) to obtain a flexible porous electrode (NPC/CNTF). It is worth noting that the introduction of adenine at different ratios did not change the structure of UiO-66. We also investigated the effect of carbonization temperature from 800 to 1000°C on the electrochemical properties of the NPC. The ratio (H 2 BDC:adenine) 9 : 1 and the NPC carbonized at 900°C (denoted as NPC-1-900) exhibits better electrochemical properties. The results show that NPC-1-900/CNTF electrode exhibits an exceptional areal capacitance of 121.5 mF cm –2 compared to that of PC-900/CNTF electrode (22.8 mF cm –2 ) at 5 mV s –1 in a three-electrode system, indicating that the incorporation of nitrogen is beneficial to the electrochemical properties of nanoporous carbon. A symmetric flexible solid-state supercapacitor of NPC-1-900/CNTF has also been assembled and tested. Electrochemical data show that the device exhibited superior areal capacitance (43.2 mF cm –2 ) at the scan rate of 5 mV s –1 ; the volumetric energy density is 57.3 µWh cm –3 and the volumetric power density is 2.4 mW cm –3 at the current density of 0.5 mA cm –2 based on poly(vinyl alcohol)/H 3 PO 4 gel electrolyte. For practical application, we have also studied the bending tests of the device, which show that the device exhibits outstanding mechanical stability under different bending angles. Furthermore, the flexible device shows excellent cyclic stability, which can retain 91.5% of the initial capacitance after 2000 cycles.

Description: The present study introduces thermogravimetry with gas chromatography–mass spectrometry (TG-GC-MS) at four different heating rates to investigate the activation energy and thermal degradation behaviour of walnut shell pyrolysis. The distributed activation energy model (DAEM) was applied to investigate the activation energy. According to values of the activation energy and the correlation coefficient by the DAEM, the activation energy (98.69–267.75 kJ mol –1 ) and correlation coefficient (0.914–0.999) were determined for pyrolysis of walnut shells. GC-MS was performed to investigate the pyrolysis products from walnut shells at different critical temperature points. More than 20 different substances were identified at different temperatures from GC-MS results. With the increasing pyrolysis temperature, furan, furfural, benzene and long chain alkanes were successively identified in different GC-MS experimental results.

Description: The CO 2 gasification of Chinese Shengli lignite (SL) catalysed by K + and Ca 2+ was studied. The results showed that calcium could greatly decrease the gasification reaction temperature of SL, and the gasification reaction rates of acid-treated SL catalysed by calcium were significantly higher than that catalysed by potassium. Kinetic analysis showed that the activation energy of the reaction catalysed by calcium was much lower than that catalysed by potassium, which was the reason for the higher catalytic activity of calcium. Fourier transform infrared characterization showed that, compared with acid-treated SL, the addition of K + /Ca 2+ resulted in the significant weakening of C=O bond, and new peaks attributed to carboxylate species appeared. X-ray photoelectron spectroscopy results indicated that the numbers of C=O decreased after the metal ions were added, indicating the formation of metal–carboxylate complexes. Raman characterization showed that the I D1 / I G values increased, suggesting more structural defects, which indicated that the reactivity of coal samples had a close relation with amorphous carbon structures. Ca 2+ could interact with the carboxyl structure in lignite by both ionic forces and polycarboxylic coordination, while K + interacted with carboxyl structure mainly via ionic forces.

Description: Macadamia nut shell (MNS) is a type of waste lignocellulose obtained from macadamia nut production processing. Large MNS wastes caused serious resource waste and environmental pollution. So, preparation of hydrochars from MNS via hydrothermal carbonization (HTC) is of great significance. HTC of MNS was conducted to study the effect of process parameters, including HTC temperature (180–260°C) and residence time (60–180 min) on the properties of hydrochars. Results showed that the increase in HTC temperature and residence time decreased the mass yield of hydrochars and increased the high heating value of hydrochars. Furthermore, the C content of hydrochars increased, whereas the H and O contents decreased. Mass yield of hydrochar is 46.59%, energy yield is 64.55% and the higher heating value is 26.02 MJ kg –1 at a temperature of 260°C and time of 120 min. The surface structure of hydrochars was rougher compared with that of MNS as observed via scanning electron microscopy. The chemical and combustion behaviour of MNS and hydrochars was analysed by Fourier transform infrared spectroscopy, and thermogravimetric analysis indicated that decarboxylation and dehydration reactions were the predominant pathways during the HTC process. Results showed that HTC can facilitate the transformation of MNS into solid fuel.

Description: The electrochemical performance of an energy conversion and storage device like the supercapacitor mainly depends on the microstructure and morphology of the electrodes. In this paper, to improve the capacitance performance of the supercapacitor, the all-pseudocapacitive electrodes of lamella-like Bi 18 SeO 29 /BiSe as the negative electrode and flower-like Co 0.85 Se nanosheets as the positive electrode are synthesized by using a facile low-temperature one-step hydrothermal method. The microstructures and morphology of the electrode materials are carefully characterized, and the capacitance performances are also tested. The Bi 18 SeO 29 /BiSe and Co 0.85 Se have high specific capacitance (471.3 F g –1 and 255 F g –1 at 0.5 A g –1 ), high conductivity, outstanding cycling stability, as well as good rate capability. The assembled asymmetric supercapacitor completely based on the pseudocapacitive electrodes exhibits outstanding cycling stability (about 93% capacitance retention after 5000 cycles). Moreover, the devices exhibit high energy density of 24.2 Wh kg –1 at a power density of 871.2 W kg –1 in the voltage window of 0–1.6 V with 2 M KOH solution.

Description: The wetting of hollow fibre membranes decreases the performance of the liquid–gas membrane contactor for CO 2 capture in biogas upgrading. To solve this problem, in this work, a poly(vinylidene fluoride) (PVDF) hollow fibre membrane for a liquid–gas membrane contactor was coated with a superhydrophobic layer composed of a combination of hydrophobic SiO 2 nanoparticles and polydimethylsiloxane (PDMS) by the method of spray deposition. A rough layer of SiO 2 deposited on the PVDF membrane resulted in an enhanced surface hydrophobicity. The surface structure of the pristine PVDF significantly affected the homogeneity of the generated SiO 2 layer. A uniform surface coating on the PVDF upper layer resulted from the presence of micrometre and nanometre-sized roughness on the surface of the PVDF membrane, which was achieved with a SiO 2 concentration of 4.44 mg ml –1 (0.2 g/45 ml) in the coating solution. As a result, the water contact angle of the modified surface was recorded as 155 ± 3°, which is higher than that of the pristine surface. The high contact angle is advantageous for reducing the wetting of the membrane. Additional mass transfer resistance was introduced by the superhydrophobic layer. In addition, continuous CO 2 absorption tests were carried out in original and modified PVDF hollow fibre membrane contactors, using monoethanolamine (MEA) solution as the absorbent. A long-term stability test revealed that the modified PVDF hollow fibre membrane contactor was able to outperform the original membrane contactor and demonstrated outstanding long-term stability, suggesting that spray deposition is a promising approach to obtain superhydrophobic PVDF membranes for liquid–gas membrane absorption.