ALBERT

Description: Managing solid waste is one of the biggest challenges in urban areas around the world. Technologically advanced economies generate vast amounts of organic waste materials, many of which are disposed to landfills. In the future, efficient use of carbon containing waste and all other waste materials has to be increased to reduce the need for virgin raw materials acquisition, including biomass, and reduce carbon being emitted to the atmosphere therefore mitigating climate change. At end-of-life, carbon-containing waste should not only be treated for energy recovery (e.g. via incineration) but technologies should be applied to recycle the carbon for use as material feedstocks. Thermochemical and biochemical conversion technologies offer the option to utilize organic waste for the production of chemical feedstock and subsequent polymers. The routes towards synthetic materials allow a more closed cycle of materials and can help to reduce dependence on either fossil or biobased raw materials. This chapter summarizes carbon-recycling routes available and investigates how in the long-term they could be applied to enhance waste management in both industrial countries as well as developing and emerging economies. We conclude with a case study looking at the system-wide global warming potential (GWP) and cumulative energy demand (CED) of producing high-density polyethylene (HDPE) from organic waste feedstock via gasification followed by Fischer–Tropsch synthesis (FTS). Results of the analysis indicate that the use of organic waste feedstock is beneficial if greenhouse gas (GHG) emissions associated with landfill diversion are considered.

Description: In rural areas, access to electricity is required for better living standard, enhance income options and reduce population migration. In last decades, steady progress has been made but the status of electrification significantly varies across countries. In developing countries, about 1.6 billion people live without electricity and another 2 billion have access but to an unreliable extent. Large population also live in remote areas where extension of grid is not feasible, where people continuing to live under distress conditions. International projections reveal that number of un-electrified people will remain same by the year 2030 if similar pace of electrification is continued in future.From this perspective, the study describes what bigger countries such as India, China and Brazil are doing and where rural electrification stands in priority in a poor country like Ethiopia. Is off-grid technologies show an option for such remote locations" The two case studies of Vietnam and South Africa reveal that work carried out through external support in the absence of national policies. As a result, people have experienced the benefits of technologies but unable to retain them in long term. Electricity has given various advantages but poor affordability of the people hinders the acceptance of technologies in rural areas.The study shows the need of a framework to achieve the long-term support for rural electrification. A framework that could direct the national priorities, understands social, economic and environmental aspects of off-grid technologies, identify key areas to be strengthen, allocates the roles and responsibilities at different working levels, maintains a consistent flow of adequate finance, pursue regular monitoring process and incorporate the monitoring results, or, critical success factors into the national policies to make them more effective. Both macro- as well as micro-level approaches have been suggested in this study.

Description: After considerable improvements of wastewater treatment, the loads of nutrients and plant protection agents, deriving from agriculture and heavy metals from urban drainages effluents as well as from erosion of agricultural soils are the main sources of nutrients and harmful substances in the loads of water bodies. The targets of the project were on the one hand the analysis of the political and legislative framework of both policy fields and on the other hand the evaluation of several, selected water protection measures with regard to their contribution to reduce water pollution, their economical effects as well as their political enforceability. The focus was laid on diffuse water pollution caused by agriculture. As main reasons for the diffuse water pollution stagnating at high level, the analysis of the political framework identified a lack of implementation discipline of water law, followed by the fragmented and insufficient water protection legislation itself and the previous design of the common agricultural policy slanted towards increasing productivity. For the future co-operation of agricultural and water authorities in implementation of their reforms and better definition of "Good Farming Practice" are recommended. The second investigation level focuses on the analysis and assessment of selected measures to reduce the input of nutrients and plant protection agents. This part was done with help of calculation models focussing on the specific cost/benefit ratios for water protection. In detail the following measures have been analysed: decoupling of direct payments, coupling of livestock farming to areas, tax on mineral nitrogen, pesticide levy, buffer stripes alongside of watercourses, all season crop cover on arable land, soil cultivation procedures, changing the use of arable land, optimisation of animal nutrition, optimisation of manure storage and application, co-operative agreements, education and training. Co-operations and water protection related education and training can be highly recommended, since they improve knowledge and freedom of action. As the results on county level show, the measure "Decoupling of direct payments" would not lead to appreciable changes as far as the nutrient surpluses on farmland is concerned. "Coupling livestock farming to areas" would decrease the surpluses substantially. For this measure and Tax on mineral nitrogen, varying adaptation reactions could be expected depending on the regional specialisation in cropping or livestock farming areas. On single farm level the measures, protein adapted feeding, optimisation of manure storage and application showed the best cost-efficiency to reduce nutrient surpluses. All season crop cover on arable land and conservation tillage are highly efficient, too, and should be included in farming practice. A stronger limitation of livestock density could mean a reduction of manure, but the implementation of this measure would lead to high losses of income for farmers specialised in animal production. For reduction of diffuse water pollution caused by urban drainage political approaches as well as detailed technical measures are examined. In the area of urban drainage storm water management (especially infiltration and constructed wetlands), unsealing of paved areas and small wastewater treatment structures (for phosphorus reduction) showed best cost-effectiveness.

Description: The paper analyzes a Bolivian region for possible cultivation of the oil plant Jatropha curcas for sustainable biodiesel production in order to replace in part Bolivia's diesel imports. The specific site for this study is located in the dry region of Gran Chaco in Santa Cruz. The aim of this work is to analyse the potential of useable land and resources for sustainable biodiesel production from Jatropha without competition with edibles production using economic, environmental and social criteria. In addition the article introduces Jatropha as one of the preferred oil plants for biodiesel production in several countries and indicates its different uses. The recommendation to cultivate Jatropha for biodiesel production is based on an exploration of the possibility of land use in the selected region and the benefits Jatropha production could offer. In this manner a sustainable cultivation of Jatropha in the region of Gran Chaco is recommended to produce biodiesel and to improve some of the environmental problems facing the region.

Description: The analysis of different global energy scenarios in part I of the report confirms that the exploitation of energy efficiency potentials and the use of renewable energies play a key role in reaching global CO2 reduction targets. An assessment on the basis of a broad literature research in part II shows that the technical potentials of renewable energy technologies are a multiple of today's global final energy consumption. The analysis of cost estimates for renewable electricity generation technologies and even long term cost projections across the key studies in part III demonstrates that assumptions are in reasonable agreement. In part IV it is shown that by implementing technical potentials for energy efficiency improvements in demand and supply sectors by 2050 can be limited to 48% of primary energy supply in IEA's "Energy Technology Perspectives" baseline scenario. It was found that a large potential for cost-effective measures exists, equivalent to around 55-60% of energy savings of all included efficiency measures (part V). The results of the analysis on behavioural changes in part VI show that behavioural dimensions are not sufficiently included in energy scenarios. Accordingly major research challenges are revealed.

Description: The article assesses the material footprints of households living on a minimum amount of social benefits in Finland and discusses the consequences in terms of ecological and social sustainability. The data were collected using interviews and a questionnaire on the consumption patterns of 18 single households. The results are compared to a study on households with varying income levels, to average consumption patterns and to decent minimum reference budgets. The low-income households have lower material footprints than average and most of the material footprints are below the socially sustainable level of consumption, which is based on decent minimum reference budgets. However, the amount of resources used by most of the households studied here is still at least double that required for ecological sustainability. The simultaneous existence of both deprivation and overconsumption requires measures from both politicians and companies to make consumption sustainable. For example, both adequate housing and economic mobility need to be addressed. Measures to improve the social sustainability of low-income households should target reducing the material footprints of more affluent households. Furthermore, the concept of what constitutes a decent life should be understood more universally than on the basis of standards of material consumption.

Description: Current production and consumption patterns remain unsustainable: Global economic growth reaches planetary boundaries and puts increasing pressure on the world's natural resources. Whereas most economic actors just react to environmental pressures, proactive market actors and other non-governmental organisations, e.g. greentec firms or fair trade organisations, turn them into market opportunities or even create standards or certification schemes as promising problem-solving market instruments in global value chains. However, how legitimate are standards and certification schemes developed by collaborating non-state actors for sustainability in global value chains? What are conditions for the success of those market-based governance mechanisms? This paper discusses the legitimacy and effectiveness of standard setting in the case of palm oil and focuses on the Roundtable of Sustainable Palm Oil (RSPO) as the first global standard setting initiative in this respect. Conditions for the success of sustainability standard setting in global value chains are identified based on the concept of non-state market-driven (NSMD) governance, based on literature review and expert interviews on standard setting. Results from the case study on RSPO highlight strengths and weaknesses of its standard setting process in the light of increasing market demand for palm oil.

Description: Several countries with large coal deposits but limited domestic oil reserves show high interest in coal-to-liquid (CtL) technologies, which could reduce crude oil imports by converting coal into liquid hydrocarbon fuels. After decades of successful large-scale operating experiences in South Africa, CtL activities in the United States, China and Germany have been fanned by the high oil price in the last years. However, CtL indicates negative techno-economic and resource-related features, such as high capital costs, high greenhouse gas discharges and high water consumption. Therefore, the technology's diffusion strongly depends on a favourable framework of policies and strong technology advocates. Daniel Vallentin analyses interdependencies between technical and non-technical parameters affecting the diffusion of CtL technologies in the United States, China and Germany. Applying the inter-disciplinary technological system approach, he identifies factors which determine the market prospects of CtL in these countries, including costs, the geographic distribution of coal reserves, actor constellations and technology, energy and climate policies. At the end of his study, he derives general conclusions with regard to driving forces and barriers for CtL diffusion. As the investigated countries are major consumers of energy and belong to the world's largest emitters of greenhouse gases, their strategies in substituting crude oil based fuels are of utmost global relevance. Therefore, Vallentin's study is recommended to experts, planners, decision-makers, and politicians in the field of climate and resource protection.

Description: Material flows induced by national economies can be regarded as indirect pressure indicators for environmental degradation. Economy-wide material flow analysis and indicators have been designed to monitor material and energy flows at the macroeconomic level and to provide indicators, which could contribute to management of resourceuse and output emission flows from both economic, environmental and broader sustainability points of view. These indicators can serve various purposes including monitoring the material basis of national economies and related environmental pressures, assessment of the material and resource productivity and monitoring the implications of trade and globalisation. The main part of this paper compares the material and resourceuse of the Czech Republic, Germany and the EU-15 by means of DMI and TMR indicators over the period of 1991–2004 (1991–2000 for EU-15). At the aggregate level both indicators in all three economies do not show any clear decreasing or increasing trends over the period considered. This means that environmental pressure related to use of materials for production and consumption purposes remains rather stable. All the economies however, recorded an increase in the efficiency of transforming the material/resource inputs into economic output. The analysis further revealed that most of the dynamics of DMI and TMR in the Czech Republic tended towards a higher similarity with Germany and the EU-15. In the future, further decreases in DMI as well as in TMR of fossils fuels might be expected in the Czech Republic, which could be counteracted by increase in DMI and TMR of metal ores/metal resources and non-metallic minerals/non-metallic resources. The future development of total DMI, TMR and material/resource intensity in both the Czech Republic and Germany will depend on further shifts to less material intensive industries and services and on increasing material efficiency in production and consumption of particular products. This is not only a technological, but also a social challenge, as there are barriers in current mode of governance and in shaping of current economic and social systems to do so.

Description: The ongoing increase of the world population entails huge challenges for all countries' agro-food systems. Agriculture has to satisfy growing food requirements both in quantitative and qualitative terms, but the on hand natural resource stock is quickly depleting. Moreover, food production and energy production from biomass are competing for land. The thesis aims at measuring the environmental impact of nutrition in three agri-food systems. The study considers the amount of natural resources used in the production and consumption of food along its life-cycle. It is featured in two parts. In the first one the analysis is restricted to the supply chain of food, and provides a sustainability rating of thirty-seven products, grown through different agricultural practices. The second analysis takes into consideration all the value chain according to three paradigms of agri-food systems. They refers to different models of food production and consumption, observed in Italy. The first one is the dominant paradigm, including conventional and intensive farming practices, long and globalized food chains, retailing in supermarkets. The other models refer to Alternative Food Networks (AFN). The first is the GAS (Gruppi di Acquisto Solidali) initiative, i.e. solidarity purchasing groups, that manage collectively the purchasing of organic food and natural manufactured products mainly from local enterprises and farmers. They aim at accessing high quality and naturally grown food, avoiding the retailing passage and ensuring a fair price to the farmers. The third model refers to UPM (Un Punto Macrobiotico), an international association established in the Marche region in 1980. It manages and controls an entire food chain, since the agricultural production, based on the post-organic technique "Ma-Pi polyculture", till the food purchasing and catering, in sixty-three restaurants spread in the Italian territory. UPM is a very consumer-oriented food chain, in which a very exigent demand (in terms of food naturality and healthiness) drives the agricultural production towards the minimization of the external inputs employment. A further model concerns the reduction of the "Food Miles", i.e. the kilometres covered by food, since the dominant paradigm. Thus, in this model the distances are reduced by an average 90%, while the production practices do not change. The methodology used for assessing the sustainability of food is the Material Input Per Service unit (MIPS) indicator. It estimates the overall environmental pressure caused by products or services by indicating the life-cycle-wide consumption of natural resources in relation to the benefit provided. It includes five resource categories: abiotic and biotic materials (renewable resources), water, air and soil. Results of the first analysis provide a dataset of the material intensity of Italian agricultural products and foodstuffs, which can expedite future research on the topic of nutrition’s sustainability. The second analysis evaluates the natural resource demand for feeding one person during a week, in the paradigms under investigation. With respect to the dominant, the GAS model allows a 58% reduction in the abiotic resource demand, 53% in water and 71% in air. The UPM system, instead, permits a tenfold reduction in abiotic, biotic and water, and 82% decrease in the air category. The insight on the socio-economic features of the systems, together with the environmental sustainability measurement, allowed making some general conclusions and policy recommendations on the sustainability of the different food systems. The role of a low external input technology in agriculture is emphasized as a possible strategy for driving food system towards more sustainable patterns and empowering the small-scale farming.

Description: The field of nutrition is facing numerous social, ecological and economic challenges in the coming decades. The food industry belongs to the most significant economic sectors worldwide and the increasing population of 9 billion in 2050 will cause a growing demand on food. So far, changing lifestyles, especially the global rising consumption of meat and dairy products are increasing environmental damage. Moreover our health and wellbeing are the direct result of healthy or unhealthy nourishment and influence follow-up indicators like individual and public health, the expense of the health sector and work productivity. The material footprint is a tool to measure and optimize the resource consumption of both products and their ingredients and the production processes along the whole value chain. It covers the whole life cycle of the products, from the extraction of raw materials to the processing industry, distribution, consumption, recycling, and disposal. In order to decrease resource consumption to a level in line with the planetary boundaries, the material footprint of household consumption should achieve a level of six to eight tonnes per capita in a year by 2050. This means a reduction in natural resource consumption by a factor of 5 to 10 in Western European countries. In order to ensure a decent lifestyle for all people in 2050, also the material footprint of nutrition has to be reduced significantly by 2050. The paper shows the relevance and role of nutrition in the overall material footprint of households on the basis of existing studies on the overall resource consumption caused by household consumption. Quantified meal and diet examples are given. It also discusses the causes of food waste and raises the question how a reduction of food waste is possible and can help decreasing the resource consumption in the food sector.

Description: Shifting the resource base for chemical and energy production from fossil feedstocks to renewable raw materials is seen by many as one of the key strategies towards sustainable development. The utilization of biomass for the production of fuels and materials has been proposed as an alternative to the petroleum-based industry. Current research and policy initiatives focus mainly on the utilization of lignocellulose biomass, originating from agriculture and forestry, as second generation feedstocks for the production of biofuels and electricity. These activities act on the assumption that significant amounts of biomass for non-food purposes are available. However, given a certain productivity per area, the current massive growth in global biofuels demand may in the long term only be met through an expansion of global arable land at the expense of natural ecosystems and in direct competition with the food-sector. Although many studies have shown the potential of biofuels production to reduce both, greenhouse gas emissions and non-renewable energy consumption, these production routes are still linear processes which depend on significant amounts of agricultural or forestry production area. Cascading use, i.e. when biomass is used for material products first and the energy content is recovered at end-of-life, may provide a greater environmental benefit than primary use as fuel. Considering waste and production residues as alternative feedstocks could help to further reduce pressures on global arable land. This research focused on thermochemical and biochemical technologies capable of utilizing organic waste or forestry residuals for energy, chemical feedstock, and synthetic materials (polymers) generation. Routes towards synthetic materials allow a closer cycle of materials and can help to reduce dependence on either fossil or biobased raw materials. The system-wide environmental burdens of three different technologies, including (1) municipal solid waste (MSW) gasification followed by Fischer-Tropsch synthesis (FTS), (2) plasma gasification of construction and demolition (C&D) wood for syngas production with energy recovery, and (3) forest residuals use in a biorefinery for polyitaconic acid (PIA) production, were assessed using life-cycle assessment. The first two studies indicated that MSW gasification and subsequent ethylene and polyethylene production via FTS has lower environmental impacts than conventional landfilling. In the future, as societies may shift towards the use of renewable energy, power offset by conventional waste-to-energy systems would not be as significant and chemicals production routes may then become increasingly competitive (in terms of environmental burdens) also to waste incineration. While production cost of Fischer-Tropsch derived chemicals seems not yet competitive to fossil-based chemicals provision, future price increases in global oil prices as well as changes in waste tipping fees, and efficiency gains on site of the waste conversion systems, may alter the economics and allow carbon recycling routes to reach a price competitive to fossil-based production routes. The third study found that plasma gasification of C&D wood for energy recovery has roughly similar environmental impacts than conventional fossil-based power systems. However, process optimization with respect to coal co-gasified, coke used as gasifier bed material, and fuel oil co-combusted in the steam boiler, would allow to significantly lower the system-wide environmental burdens. The fourth study looked at PIA production from softwood hemicellulose in a stream integrated approach (with the partially macerated wood and lignin being used in other existing processes such as pulp & paper plants for conventional pulp and bioenergy production). The assessment indicated lower global warming potential, energy demand, and acidification, for the wood-based PIA polymer, when compared to corn-based PIA and fossil-based polyacrylic acid (PAA). However, water use associated with wood-derived PIA was found to be higher than for fossil-based PAA production and land occupation is highest for the wood-derived polymer. It is hoped that results of this dissertation will add to the current debate on sustainable waste and biomass utilization and to establish future supply chains for green and sustainable chemical products.

Description: Purpose - Iran as an energy-rich country faces many challenges in the optimal utilization of its vast resources. High rates of population and economic growth, a generous subsidies program, and poor resource management have contributed to rapidly growing energy consumption and high energy intensity over the past decades. The continuing trend of rising energy consumption will bring about new challenges as it will shrink oil export revenues, restraining economic activities. This calls for a study to explore alternative scenarios for the utilization of energy resources in Iran. The purpose of this paper is to model demand for energy in Iran and develop two business-as-usual and efficiency scenarios for the period 2005-2030. Design/methodology/approach - The authors use a techno-economic or end-use approach to model energy demand in Iran for different types of energy uses and energy carriers in all sectors of the economy and forecast it under two scenarios: business as usual (BAU) and efficiency. Findings - Iran has a huge potential for energy savings. Specifically, under the efficiency scenario, Iran will be able to reduce its energy consumption 40 percent by 2030. The energy intensity can also be reduced by about 60 percent to a level lower than the world average today. Originality/value - The paper presents a comprehensive study that models the Iranian energy demand in different sectors of the economy, using data at different aggregation levels and a techno-economic end-use approach to illuminate the future of energy demand under alternative scenarios.

Description: The article estimates the natural resource consumption due to nutrition from the supply and demand sides. Using the MIPS (Material Input per Service Unit) methodology, we analyzed the use of natural resources along the supply chains of three Italian foodstuffs: wheat, rice and orange-based products. These figures were then applied for evaluating the sustainability of diets in 13 European countries. The results outline which phases in food production are more natural resource demanding than others. We also observed different levels of sustainability in the European diets and the effect of different foodstuffs in the materials, water and air consumption.

Description: The study presents the results of an integrated assessment of carbon capture and storage (CCS) in the power plant sector in Germany, with special emphasis on the competition with renewable energy technologies. Assessment dimensions comprise technical, economic and environmental aspects, long-term scenario analysis, the role of stakeholders and public acceptance and regulatory issues. The results lead to the overall conclusion that there might not necessarily be a need to focus additionally on CCS in the power plant sector. Even in case of ambitious climate protection targets, current energy policy priorities (expansion of renewable energies and combined heat and power plants as well as enhanced energy productivity) result in a limited demand for CCS. In case that the large energy saving potential aimed for can only partly be implemented, the rising gap in CO2 reduction could only be closed by setting up a CCS-maximum strategy. In this case, up to 22% (41 GW) of the totally installed load in 2050 could be based on CCS. Assuming a more realistic scenario variant applying CCS to only 20 GW or lower would not be sufficient to reach the envisaged climate targets in the electricity sector. Furthermore, the growing public opposition against CO2 storage projects appears as a key barrier, supplemented by major uncertainties concerning the estimation of storage potentials, the long-term cost development as well as the environmental burdens which abound when applying a life-cycle approach. However, recently, alternative applications are being increasingly considered–that is the capture of CO2 at industrial point sources and biomass based energy production (electricity, heat and fuels) where assessment studies for exploring the potentials, limits and requirements for commercial use are missing so far. Globally, CCS at power plants might be an important climate protection technology: coal-consuming countries such as China and India are increasingly moving centre stage into the debate. Here, similar investigations on the development and the integration of both, CCS and renewable energies, into the individual energy system structures of such countries would be reasonable.

Description: Wind energy that can neither be fed into the grid nor be used regionally must be curtailed. This paper proposes different options to deal with such surplus wind energy amounts in a time horizon until 2020. It assesses their ability to handle the surplus energy in a sustainable way using a multi criteria analysis. The paper bases on a study that was prepared for the Ministry for Climate Protection, Environment, Agriculture, Nature Conservation and Consumer Protection of North Rhine-Westphalia between 2010 and 2012.

Description: The final report of the research project "Power Sector Decarbonisation: Metastudy" contains the various reports prepared by Öko-Institut and Wuppertal Institute during the course of the SEFEP funded project. A key objective of the project was to make a contribution to the debates within the European Union (EU) and Member States on the EU's Energy Roadmap 2050 publication, which was released in December 2011. This objective was achieved by systematically analysing and comparing recently published scenarios on the European electricity sector commissioned by a range of different stakeholders (environmental NGOs, industry and government agencies).

Description: If the current energy policy priorities are retained, there may be no need to focus additionally on carbon capture and storage (CCS) in the power plant sector of Germany. This applies even in the case of ambitious climate protection targets, according to the results of the presented integrated assessment study. These cover a variety of aspects: Firstly, the technology is not expected to become available on a large scale in Germany before 2025. Secondly, if renewable energies and combined heat and power are expanded further and energy productivity is enhanced, there is likely to be only a limited demand for CCS power plants, as a scenario analysis of CCS deployment in Germany shows. Thirdly, cost analysis using the learning curve approach shows that the electricity generation costs of renewable electricity approach those of CCS power plants. This leads to the consequence that, from 2020, several renewable technologies may well be in a position to offer electricity at a cheaper rate than CCS power plants. In addition, a review of new life cycle assessments for CO2 separation in the power plant sector indicates that the greenhouse gas emissions from 1 kW h of electricity generated by first-generation CCS power plants could only be reduced by 68 % to 87 % (95 % in individual cases). Finally, a cautious, conservative estimate of the effective German CO2 storage capacity of approximately 5 billion tonnes of CO2 is calculated, including a fluctuation range yielding values between 4 and 15 billion tonnes of CO2. Therefore, the total CO2 emissions caused by large point sources in Germany could be stored for 12 years (basic value) or for 8 or 33 years (sensitivity values).

Description: This paper examines the effects of an increased integration of concentrated solar power (CSP) into the conventional electricity systems of Morocco and Algeria. A cost-minimizing linear optimization tool was used to calculate the best CSP plant configuration for Morocco's coal-dominated power system as well as for Algeria, where flexible gas-fired power plants prevail. The results demonstrate that in both North African countries, storage-based CSP plants offer significant economic advantages over non-storage, low-dispatchable CSP configurations. However, in a generalized renewable integration scenario, where CSP has to compete with other renewable generation technologies, like wind or photovoltaic (PV) power, it was found that the cost advantages of dispatchability only justify CSP investments when a relatively high renewable penetration is targeted in the electricity mix.

Description: Global trade is increasingly being challenged by observations of growing burden shifting, in particular of environmental problems. This paper presents the first worldwide calculations of shifted burden based on material flow indicators, in particular direct and indirect physical trade balances. This study covers the period between 1962 and 2005 and includes between 82 and 173 countries per year. The results show that indirect trade flow volumes have increased to around 41 billion tonnes in 2005. The traded resources with the highest share of associated indirect flows are iron, hard coal, copper, tin and increasingly palm oil. Regarding the burden balance between regions, Europe is the biggest shifter whereas Australia and Latin America are the largest takers of environmental burden due to resource extraction. To evaluate the findings from a global perspective, the results are analysed in terms of resource flow induced environmental pressure related to a country's land area in terms of total and per capita area. Resource endowment and population density seem to be more relevant in determining the physical trade balance, including indirect flows, than income level.

Description: The cement industry is one of the major energy consuming and CO2 emitting sectors in China. In 2010, 1,868 million tons of cement has been produced, which accounted for 56.1% of the world's total cement production. The 11th Five-Year Plan (FYP) (2006-2010) included policy measures for CO2 emission abatement in cement production. Based on the main governmental framework of CO2 mitigation policies at national level in the cement sector, key policies and technologies used during this period are identified and their effects on CO2 reduction are assessed. This paper calculates the reduction of CO2 emissions related to four main policies and technologies for efficient cement production in the 11th and the 12th FYP (2011-2015) with 2005 as a reference year. These are waste heat recovery, closing outdated facilities, substitution for clinker production and other technologies aiming to increase energy efficiency. Due to these measures, we estimate that a total CO2 emission reduction during the 11th FYP of 397 million tonnes could be saved, which is considerably different to 185.75 million tonnes estimated by Zeng (2008) and 303 million tonnes by the NDRC by using different calculation methods. Of the four technologies, the 4th group of energy efficiency increasing techniques was the most important policy and avoided the largest amount of CO2 emissions. Previous energy intensity reduction was mainly due to the outdated production closing and energy efficiency improving. Based on the assessment of technology performance, it appears that there is still a large emission reduction potential in cement production processes. The paper calculates this potential for the 12th FYP period (2011-2015) based on these four identified policy measures. The result is compared to the Chinese government targets in the 12th FYP and promising future CO2 mitigation policies and technologies are proposed, such as the use of alternative energy.

Description: In the past few decades, geochemically scarce metals have become increasingly relevant for emerging technologies in domains such as energy supply and storage, information and communication, lighting or transportation, which are regarded as cornerstones in the transition towards a sustainable post-fossil society. Accordingly, the supply risks of scarce metals and possible interventions towards their more sustainable use have been subject to an intense debate in recent studies. In this article, we integrate proposed intervention options into a generic life cycle framework, taking into account issues related to knowledge provision and to the institutional setting. As a result, we obtain a landscape of intervention fields that will have to be further specified to more specific intervention profiles for scarce metals or metals families. The envisioned profiles are expected to have the potential to reduce action contingency and to contribute to meeting the sustainability claims often associated with emerging technol ogies.

Description: Greenhouse gas emission reductions are at the centre of national and international efforts to mitigate climate change. In road transportation, many politically incentivised measures focus on increasing the energy efficiency of established technologies, or promoting electric or hybrid vehicles. The abatement potential of the former approach is limited, electric mobility technologies are not yet market-ready. In a case study for Germany, this paper focuses on natural gas powered vehicles as a bridging technology in road transportation. Scenario analyses with a low level of aggregation show that natural gas-based road transportation in Germany can accumulate up to 464 million tonnes of CO2-equivalent emission reductions until 2030 depending on the speed of the diffusion process. If similar policies were adopted EU-wide, the emission reduction potential could reach a maximum of about 2.5 billion tonnes of CO2-equivalent. Efforts to promote natural gas as a bridging technology may therefore contribute to significant emissions reductions.

Description: Defining the prevention of waste as top priority of the waste hierarchy - as confirmed by the revised Waste Framework Directive (WFD) - is much more than a simple amendment of ways to deal with waste, but means nothing less than a fundamental change of the socio-technical system of waste infrastructures and requires a transition from end-of-pipe technologies towards an integrated management of resources. The WFD therefore obligates member states to develop national waste prevention programs as a new policy instrument with the development of waste prevention indicators as one of the core elements. The article discusses the limitations of waste-based key figures and shows the need for more process-oriented indicators. As part of the development of national waste prevention programs such indicators reveal the relevance of different barriers that have to be overcome in order to make prevention an effective top priority in the waste hierarchy. With regard to path dependencies caused by sunk costs in end-of-pipe waste infrastructures the absolute amount of integrated environmental investments, as well as their share of the total waste-related investments, can be seen as indicators for the level of innovation activities aimed at waste prevention. Sector-specific indicators for the production phase could be used as benchmarks and to highlight differences in the need for policy interventions.

Description: Consumption of natural resources should not exceed sustainable levels. The increasing use of biofuels and to some extent biomaterials, on top of rising food and feed demands, is causing countries to use a growing amount of global land, which may lead to land use conflicts and the expansion of cropland and intensive cultivation at the expense of natural ecosystems. Selective product certification cannot control the land use change triggered by growing overall biomass consumption. We propose a comprehensive approach to account for the global land use of countries for their domestic consumption, and assess this level with regard to globally acceptable levels of resource use, based on the concept of safe operating space. It is shown that the European Union currently uses one-third more cropland than globally available on a per capita basis and that with constant consumption levels it would exceed its fair share of acceptable resource use in 2030. As the use of global forests to meet renewable energy targets is becoming a concern, an approach to account for sustainable levels of timber flows is also proposed, based on the use of net annual increment, exemplified with preliminary data for Switzerland. Altogether, our approach would integrate the concept of sustainable consumption into national resource management plans; offering a conceptual basis and concrete reference values for informed policy making and urging countries to monitor and adjust their levels of resource consumption in a comprehensive way, respectful of the limits of sustainable supply.

Description: In a new waste hierarchy the amended EU Waste Framework Directive (WFD) (2008/98/EG) confirmed the prevention of waste as a priority measure to protect the environment with regard to the production and handling of waste. Amongst others the Member States are requested to promote waste prevention. According to article 29 par. 1 WFD the prevention measures have to be planned in terms of waste prevention programmes to be created by the Member States until December 12th 2013. These prevention programmes are to describe existing waste prevention measures and set waste prevention goals. The progress is to be monitored and assessed by targeting appropriate, specific qualitative or quantitative benchmarks for adopted waste prevention measures. The programmes may be included in waste management plans or other environmental programmes. By the objectives and measures of prevention programmes the environmental impacts associated with generation of waste shall be decoupled from economic growth.

Description: Concerns over climate change and the security of industrial feedstock supplies have been opening a growing market for biobased materials. This development, however, also presents a challenge to scientists, policy makers, and industry because the production of biobased materials requires land and is typically associated with adverse environmental effects. This article addresses the environmental impacts of biobased materials in a meta-analysis of 44 life cycle assessment (LCA) studies. The reviewed literature suggests that one metric ton (t) of biobased materials saves, relative to conventional materials, 55 ± 34 gigajoules of primary energy and 3 ± 1 t carbon dioxide equivalents of greenhouse gases. However, biobased materials may increase eutrophication by 5 ± 7 kilograms (kg) phosphate equivalents/t and stratospheric ozone depletion by 1.9 ± 1.8 kg nitrous oxide equivalents/t. Our findings are inconclusive with regard to acidification (savings of 2 ± 20 kg sulfur dioxide equivalents/t) and photochemical ozone formation (savings of 0.3 ± 2.4 kg ethene equivalents/t). The variability in the results of life cycle assessment studies highlights the difficulties in drawing general conclusions. Still, common to most biobased materials are impacts caused by the application of fertilizers and pesticides during industrial biomass cultivation. Additional land use impacts, such as the potential loss of biodiversity, soil carbon depletion, soil erosion, deforestation, as well as greenhouse gas emissions from indirect land use change are not quantified in this review. Clearly these impacts should be considered when evaluating the environmental performance of biobased materials.

Description: The energy potential of agricultural residues in Tanzania has so far not been evaluated and quantified sufficiently. Moreover, the scientific basis for estimations of the sustainable potential of wastes and residues is still very limited. This paper presents an attempt to evaluate the theoretical and technical potential of residues from the sisal sector in Tanzania with regards to energy recovery through anaerobic digestion. The characteristics and availability of sisal residues are defined and a set of sustainability indicators with particular focus on environmental and socio-economic criteria is applied. Our analysis shows that electricity generation with sisal residues can be sustainable and have positive effects on the sustainability of sisal production itself. All sisal residues combined have an annual maximum electricity potential of 102 GW h in 2009, corresponding to up to 18.6 MW of potential electric capacity installations. This estimated maximum potential is equivalent to about 3 % of the country's current power production. Utilizing these residues could contribute to meeting the growing electricity demand and offers an opportunity for decentralized electricity production in Tanzania.

Description: A weekly publication devoted to the scientific work at marine biological laboratories.

Description: Vol. 9. 10 numbered issues published from June 30-Sept. 1, 1934. Numbered both as issues 1-10 and issues 72-81.

Description: Publications

Description: A weekly publication concerned with the activities of the Marine Biological Laboratory and of Woods Hole.

Description: Vol. 3. 8 numbered issues published from July 7-Aug. 25, 1928. Includes Jacques Loeb Memorial Supplement

Description: Publications

Description: A weekly publication devoted to the activities of the Marine Biological Laboratory and of Woods Hole in general.

Description: Vol. 2. 8 numbered issues published from July 8-Aug. 27, 1927

Description: Publications

Description: A publication devoted to the scientific work at marine biological laboratories. A bi-weekly publication devoted to the scientific work at marine biological laboratories. A fortnightly publication devoted to the scientific work at marine biological laboratories.

Description: v. 18 issued as a single volume in November 1943. Also numbered as "Whole No. 153". July 20, 1946 issue published as v. 18, no.1. August 3, 1946 issue published as v.18, no. 2. August 17, 1946 issue published as vol. 19, no. 3.

Description: Publications

Description: Issued under the auspices of the M.B.L. Club

Description: Vol. 1. 6 numbered issues (no. 1 without title) published from July 21-Aug. 26, 1926

Description: Publications

Description: A weekly publication devoted to the scientific work at Woods Hole.

Description: Vol. 7. 10 numbered issues published from June 25-Aug. 27, 1932. Numbered both as issues 1-10 and issues 51-60. Issue 10 [60] includes Marine Biological Laboratory Chemical Room Formulae and Methods II, edited by Oscar W. Richards.

Description: Publications

Description: A weekly publication concerned with the activities of the Marine Biological Laboratory and of Woods Hole.

Description: Vol. 4. 8 numbered issues published from July 6-Aug. 25, 1929. Includes the following supplements: Serial publications held by the Marine Biological Laboratory, June 15, 1929; "?????" news supplements vol. 1, no. 1-3, published July 25, 1929, July 29, 1929, and August 5, 1929; Woods Hole Log, vol. 1, no. 5-7, published August 19, 1929, Sept. 4, 1929, and Sept. 18, 1929.

Description: Publications

Description: A weekly publication devoted to the scientific work at Woods Hole.

Description: Vol. 5. 10 numbered issues published from June 28-Aug. 30, 1930. Numbered both as issues 1-10 and issues 31-40. Includes anniversary supplement in honor of Professor Frank R. Lillie, published June 28, 1930. Includes supplement published August 30, 1930 - Marine Biological Laboratory Chemical Room Formulae and Methods, edited by Oscar W. Richards.

Description: Publications

Description: A weekly publication devoted to the scientific work at Woods Hole.

Description: Vol. 6. 10 numbered issues published from June 27-Aug. 29, 1931. Numbered both as issues 1-10 and issues 41-50.

Description: Publications

Description: A weekly publication devoted to the scientific work at marine biological laboratories.

Description: Vol. 12. 9 numbered issues published from July 3-Aug. 28, 1937. Numbered both as issues 1-9 and issues 101-109.

Description: Publications

Description: A weekly publication devoted to the scientific work at marine biological laboratories.

Description: Vol. 10. 10 numbered issues published from July 6-Sept. 7, 1935. Numbered both as issues 1-10 and issues 82-91.

Description: Publications