ALBERT

Description: Foam is used extensively as packing material for items sent to the International Space Station (ISS). Although lightweight, foam is bulky and can occupy a large fraction of the limited ISS volume. Four chemically distinct foams have been used on the ISS. In descending order of current usage, these are Plastazote Zotek Minicel Pyrell. Processing foam with the Heat Melt Compactor (HMC), a solid waste treatment system, has been proposed to reduce the volume of foams stored on spacecraft. Prior to HMC testing, Thermogravimetric Analyses were conducted on the four foams as a precaution to ensure that the thermal decomposition temperatures were not within range of HMC operation (180C). Pyrell was not tested with the HMC because it is known to release toxic compounds and comprises less than 1.5 of total foam usage on ISS resupply flights. Zotek, Minicel, Plastazote LD24FR (low density), and Plastazote LD45FR (high density) were processed with the HMC at 130, 150 and 170C. Volume was reduced by 82.6 on average (n19; std dev4.88). Hydrocarbons and several other compounds emitted during foam processing were measured using a Total Hydrocarbon Analyzer and FTIR. Effects of process temperature and foam type on exhaust composition are discussed. Feeding of foams into the limited size opening of the HMC compaction chamber is likely to be a challenge, particularly in microgravity. Some suggestions are proposed to facilitate feeding foam into the HMC. Processing packing foam with the HMC has been shown to substantially reduce foam volume, and also has the potential benefit of producing radiation-shielding foam tiles.

Description: Traditionally, infrared (IR) space instruments have been focused by iterating with a number of different thickness shim rings in a thermal vacuum chamber until the focus meets requirements. This has required a number of thermal cycles that are very expensive as they tie up many integration and test (I&T)/ environmental technicians/engi neers work ing three shifts for weeks. Rather than creating a test shim for each iteration, this innovation replaces the test shim and can focus the instrument while in the thermal vacuum chamber. The focus tool consists of three small, piezo-actuated motors that drive two sets of mechanical interface flanges between the instrument optics and the focal- plane assembly, and three optical-displacement metrology sensors that can be read from outside the thermal vacuum chamber. The motors are used to drive the focal planes to different focal distances and acquire images, from which it is possible to determine the best focus. At the best focus position, the three optical displacement metrology sensors are used to determine the shim thickness needed. After the instrument leaves the thermal vacuum chamber, the focus tool is replaced with the precision-ground shim ring. The focus tool consists of two sets of collars, one that mounts to the backside of the interface flange of the instrument optics, and one that mounts to the backside of the interface flange of the focal plane modules. The collars on the instrument optics side have the three small piezo-actuated motors and the three optical displacement metrology systems. Before the instrument is focused, there is no shim ring in place and, therefore, no fasteners holding the focal plane modules to the cameras. Two focus tooling collars are held together by three strong springs. The Orbiting Carbon Observatory (OCO) mission spectrometer was focused this way (see figure). The motor described here had to be moved five times to reach an acceptable focus, all during the same thermal cycle, which was verified using pupil slicing techniques. A focus accuracy of .20.100 microns was achieved.

Description: A method was developed of obtaining propulsive base flow data in both hot and cold jet environments, at Mach numbers and altitude of relevance to NASA launcher designs. The base flow data was used to perform computational fluid dynamics (CFD) turbulence model assessments of base flow predictive capabilities in order to provide increased confidence in base thermal and pressure load predictions obtained from computational modeling efforts. Predictive CFD analyses were used in the design of the experiments, available propulsive models were used to reduce program costs and increase success, and a wind tunnel facility was used. The data obtained allowed assessment of CFD/turbulence models in a complex flow environment, working within a building-block procedure to validation, where cold, non-reacting test data was first used for validation, followed by more complex reacting base flow validation.

Description: Spectroscopic studies of ionized gas in electromagnetic shock tube

Description: Jet outflow of metallic plasma into vacuum and applicability of metallic plasma jets in heat transfer studies of plasma flow to solid wall and aerodynamic studies of plasma flows

Description: Propagation theory for pulsed electromagnetic fields in moving conductive media

Description: Longitudinal edge effect in linear induction magnetohydrodynamic generators

Description: Electromagnetic processes in conduction band of traveling magnetic field of flat inductor in magnetohydrodynamic machines

Description: Magnetohydrodynamic induction generators with liquid metal working media, and electromagnetic field structures

Description: An apparatus and method for storing and delivering fluid to a person comprises, in at least one specific embodiment, a fluid reservoir having an internal volume therein with an opening disposed through a first wall or a second wall of the fluid reservoir and located toward a first end of the fluid reservoir. A first portion of a tube can be exterior to the fluid reservoir and a second portion of the tube can be disposed through the opening and within the internal volume. At least one insulation layer can be disposed about the exterior of the first wall of the fluid reservoir. The second wall of the fluid reservoir can be configured for transferring heat from or to the internal volume or from the person. At least one baffle is disposed within the internal volume and connected to the first wall and the second wall of the fluid reservoir.