ALBERT

Description: Ph. Traore and A. T. Perez Two-dimensional numerical simulations are carried out to examine the problem of transient electroconvection stability of dielectric liquids subjected to unipolar injection. The entire set of electrohydrodynamics equations associated with the electroconvective phenomena that occur in a layer of a die ... [Phys. Fluids 24, 037102 (2012)] published Thu Mar 8, 2012.

Description: Improving fingerprint matching algorithms is an active and important research area in fingerprint recognition. Algorithms based on minutia triplets, an important matcher family, present some drawbacks that impact their accuracy, such as dependency to the order of minutiae in the feature, insensitivity to the reflection of minutiae triplets, and insensitivity to the directions of the minutiae relative to the sides of the triangle. To alleviate these drawbacks, we introduce in this paper a novel fingerprint matching algorithm, named M3gl. This algorithm contains three components: a new feature representation containing clockwise-arranged minutiae without a central minutia, a new similarity measure that shifts the triplets to find the best minutiae correspondence, and a global matching procedure that selects the alignment by maximizing the amount of global matching minutiae. To make M3gl faster, it includes some optimizations to discard non-matching minutia triplets without comparing the whole representation. In comparison with six verification algorithms, M3gl achieves the highest accuracy in the lowest matching time, using FVC2002 and FVC2004 databases.

Description: Pollution of drinking water sources represents a continuously emerging problem in global environmental protection. Novel techniques for real-time monitoring of water quality, capable of the detection of unanticipated toxic and bioactive substances, are urgently needed. In this study, the applicability of a cell-based sensor system using selected eukaryotic cell lines for the detection of aquatic pollutants is shown. Readout parameters of the cells were the acidification (metabolism), oxygen consumption (respiration) and impedance (morphology) of the cells. A variety of potential cytotoxic classes of substances (heavy metals, pharmaceuticals, neurotoxins, waste water) was tested with monolayers of L6 cells (rat myoblasts). The cytotoxicity or cellular effects induced by inorganic ions (Ni2+ and Cu2+) can be detected with the metabolic parameters acidification and respiration down to 0.5 mg/L, whereas the detection limit for other substances like nicotine and acetaminophen are rather high, in the range of 0.1 mg/L and 100 mg/L. In a close to application model a real waste water sample shows detectable signals, indicating the existence of cytotoxic substances. The results support the paradigm change from single substance detection to the monitoring of overall toxicity.

Description: Small noncoding microRNAs (miRNAs) are important regulators of post-transcriptional gene regulation and have altered the prevailing view of a linear relationship between gene and protein expression. Aberrant miRNA expression is an emerging theme for a wide variety of diseases, highlighting the fundamental role played by miRNAs in both physiological and pathological states. The identification of stable miRNAs in bodily fluids paved the way for their use as novel biomarkers amenable to clinical diagnosis in translational medicine. Identification of miRNAs in exosomes that are functional upon delivery to the recipient cells has highlighted a novel method of intercellular communication. Delivery of miRNAs to recipient cells via blood, with functional gene regulatory consequences, opens up novel avenues for target intervention. Exosomes thus offer a novel strategy for delivering drugs or RNA therapeutic agents. Though much work lies ahead, circulating miRNAs are unequivocally ushering in a new era of novel biomarker discovery, intercellular communication mechanisms, and therapeutic intervention strategies.

Description: In this paper, a novel principle of contactless gauge block calibration is presented. The principle of contactless gauge block calibration combines low-coherence interferometry and laser interferometry. An experimental setup combines Dowell interferometer and Michelson interferometer to ensure a gauge block length determination with direct traceability to the primary length standard. By monitoring both gauge block sides with a digital camera gauge block 3D surface measurements are possible too. The principle presented is protected by the Czech national patent No. 302948.

Description: Quorum sensing (QS) is a population density-dependent regulatory mechanism in which gene expression is coupled to the accumulation of a chemical signaling molecule. QS systems are widespread among the plant soft-rotting bacteria. In Pectobacterium carotovorum, at least two QS systems exist being specified by the nature of chemical signals involved. QS in Pectobacterium carotovorum uses N-acylhomoserine lactone (AHL) based, as well as autoinducer-2 (AI-2) dependent signaling systems. This review will address the importance of the QS in production of virulence factors and interaction of QS with other regulatory systems in Pectobacterium carotovorum.

Description: Optical fibers possess many advantages such as small size, light weight and immunity to electro-magnetic interference that meet the sensing requirements to a large extent. In this investigation, a Mach-Zehnder interferometric optical fiber sensor is used to measure the dynamic strain of a vibrating cantilever beam. A 3 × 3 coupler is employed to demodulate the phase shift of the Mach-Zehnder interferometer. The dynamic strain of a cantilever beam subjected to base excitation is determined by the optical fiber sensor. The experimental results are validated with the strain gauge.

Description: Joint estimation of direction-of-arrival (DOA) and polarization with electromagnetic vector-sensors (EMVS) is considered in the framework of complex-valued non-orthogonal joint diagonalization (CNJD). Two new CNJD algorithms are presented, which propose to tackle the high dimensional optimization problem in CNJD via a sequence of simple sub-optimization problems, by using LU or LQ decompositions of the target matrices as well as the Jacobi-type scheme. Furthermore, based on the above CNJD algorithms we present a novel strategy to exploit the multi-dimensional structure present in the second-order statistics of EMVS outputs for simultaneous DOA and polarization estimation. Simulations are provided to compare the proposed strategy with existing tensorial or joint diagonalization based methods.

Description: Frederic Moisy, Guy-Jean Michon, Marc Rabaud, and Eric Sultan Capillary waves excited by the vertical oscillation of a thin elongated plate below an air-water interface are analyzed using time-resolved measurements of the surface topography. A parametric instability is observed above a well defined acceleration threshold, resulting in a so-called cross-wave, a ... [Phys. Fluids 24, 022110 (2012)] published Fri Feb 24, 2012.

Description: Gary P. Matson and Andrew J. Hogg Gravitationally driven exchange flows of viscous fluids with different densities are analysed theoretically and investigated experimentally within a horizontal channel. Following initiation from rest when there is a vertical boundary dividing the two fluids, the denser fluid slumps under the less de ... [Phys. Fluids 24, 023102 (2012)] published Fri Feb 24, 2012.

Description: The development of a rapid, sensitive, specific method for the foodborne pathogenic bacteria detection is of great importance to ensure food safety and security. In recent years impedimetric biosensors which integrate biological recognition technology and impedance have gained widespread application in the field of bacteria detection. This paper presents an overview on the progress and application of impedimetric biosensors for detection of foodborne pathogenic bacteria, particularly the new trends in the past few years, including the new specific bio-recognition elements such as bacteriophage and lectin, the use of nanomaterials and microfluidics techniques. The applications of these new materials or techniques have provided unprecedented opportunities for the development of high-performance impedance bacteria biosensors. The significant developments of impedimetric biosensors for bacteria detection in the last five years have been reviewed according to the classification of with or without specific bio-recognition element. In addition, some microfluidics systems, which were used in the construction of impedimetric biosensors to improve analytical performance, are introduced in this review.

Description: Landcover is subject to continuous changes on a wide variety of temporal and spatial scales. Those changes produce significant effects in human and natural activities. Maintaining an updated spatial database with the occurred changes allows a better monitoring of the Earth’s resources and management of the environment. Change detection (CD) techniques using images from different sensors, such as satellite imagery, aerial photographs, etc., have proven to be suitable and secure data sources from which updated information can be extracted efficiently, so that changes can also be inventoried and monitored. In this paper, a multisource CD methodology for multiresolution datasets is applied. First, different change indices are processed, then different thresholding algorithms for change/no_change are applied to these indices in order to better estimate the statistical parameters of these categories, finally the indices are integrated into a change detection multisource fusion process, which allows generating a single CD result from several combination of indices. This methodology has been applied to datasets with different spectral and spatial resolution properties. Then, the obtained results are evaluated by means of a quality control analysis, as well as with complementary graphical representations. The suggested methodology has also been proved efficiently for identifying the change detection index with the higher contribution.

Description: George Ilhwan Park, James M. Wallace, Xiaohua Wu, and Parviz Moin Using the recent direct numerical simulations by Wu and Moin [Transitional and turbulent boundary layer with heat transfer, Phys. Fluids 22, 85 (2010)] of a flat-plate boundary layer with a passively heated wall, statistical properties of the turbulence in transition at Re [approximate] 300, from in ... [Phys. Fluids 24, 035105 (2012)] published Wed Mar 14, 2012.

Description: Shintaro Imayama, P. Henrik Alfredsson, and R. J. Lingwood A new method of graphically representing the transition stages of a rotating-disk flow is presented. The probability density function contour map of the fluctuating azimuthal disturbance velocity is used to show the characteristics of the boundary-layer flow over the rotating disk as a function of R ... [Phys. Fluids 24, 031701 (2012)] published Wed Mar 14, 2012.

Description: S. Balasubramanian, G. C. Orlicz, K. P. Prestridge, and B. J. Balakumar We present an experimental study on the dependence of initial condition parameters, namely, the amplitude delta and wavenumber kappa (kappa = 2pi/lambda, where lambda is the wavelength) of perturbations, on turbulence and mixing in shock-accelerated Richtmyer-Meshkov (R-M) unstable fluid layers. A s ... [Phys. Fluids 24, 034103 (2012)] published Wed Mar 14, 2012.

Description: P. S. Landa and P. V. E. McClintock We address the problem of how turbulence is created in a submerged plane jet, near to the nozzle from which it issues. We do so by making use of a WKB-like asymptotic expansion for approximate solution of a complex, linear, fourth-order differential equation describing small deviations from the stea ... [Phys. Fluids 24, 035104 (2012)] published Wed Mar 14, 2012.

Description: A memristor bridge neural circuit which is able to perform signed synaptic weighting was proposed in our previous study, where the synaptic operation was verified via software simulation of the mathematical model of the HP memristor. This study is an extension of the previous work advancing toward the circuit implementation where the architecture of the memristor bridge synapse is built with memristor emulator circuits. In addition, a simple neural network which performs both synaptic weighting and summation is built by combining memristor emulators-based synapses and differential amplifier circuits. The feasibility of the memristor bridge neural circuit is verified via SPICE simulations.

Description: This work presents an experimental study of gold-DNA-gold structures in the presence and absence of external magnetic fields with strengths less than 1,200.00 mT. The DNA strands, extracted by standard method were used to fabricate a Metal-DNA-Metal (MDM) structure. Its electric behavior when subjected to a magnetic field was studied through its current-voltage (I-V) curve. Acquisition of the I-V curve demonstrated that DNA as a semiconductor exhibits diode behavior in the MDM structure. The current versus magnetic field strength followed a decreasing trend because of a diminished mobility in the presence of a low magnetic field. This made clear that an externally imposed magnetic field would boost resistance of the MDM structure up to 1,000.00 mT and for higher magnetic field strengths we can observe an increase in potential barrier in MDM junction. The magnetic sensitivity indicates the promise of using MDM structures as potential magnetic sensors.

Description: A flow-electrolytical cell containing a strand of micro Au modified carbon fiber electrodes (CFE) has been designedand characterized for use in a voltammatric detector for detecting cysteine using high-performance liquid chromatography. Cysteine is more efficiently electrochemical oxidized on a Au /CFE than a bare gold and carbon fiber electrode. The possible reaction mechanism of the oxidation process is described from the relations to scan rate, peak potentials and currents. For the pulse mode, and measurements with suitable experimental parameters, a linear concentration from 0.5 to 5.0 mg·L−1 was found. The limit of quantification for cysteine was below 60 ng·mL−1.

Description: V. G. Makarov The evolution of a dipolar vortex in a quasi-two-dimensional rotating flow of barotropic fluid over a flat surface with a no-slip condition in the Ekman bottom layer is considered. The vorticity equation in this case becomes nonlinear. An effect of bottom friction is displayed mainly in cyclone-anti ... [Phys. Fluids 24, 026602 (2012)] published Fri Feb 3, 2012.

Description: This paper introduces a flexible hardware and software architecture for a smart video sensor. This sensor has been applied in a video surveillance application where some of these video sensors are deployed, constituting the sensory nodes of a distributed surveillance system. In this system, a video sensor node processes images locally in order to extract objects of interest, and classify them. The sensor node reports the processing results to other nodes in the cloud (a user or higher level software) in the form of an XML description. The hardware architecture of each sensor node has been developed using two DSP processors and an FPGA that controls, in a flexible way, the interconnection among processors and the image data flow. The developed node software is based on pluggable components and runs on a provided execution run-time. Some basic and application-specific software components have been developed, in particular: acquisition, segmentation, labeling, tracking, classification and feature extraction. Preliminary results demonstrate that the system can achieve up to 7.5 frames per second in the worst case, and the true positive rates in the classification of objects are better than 80%.

Description: Leon P. J. Kamp Deviations from two-dimensionality of a shallow flow that is dominated by bottom friction are quantified in terms of the spatial distribution of strain and vorticity as described by the Okubo-Weiss function. This result is based on a Poisson equation for the pressure in a quasi-horizontal (primary) ... [Phys. Fluids 24, 023601 (2012)] published Mon Feb 6, 2012.

Description: Choon-Bum Choi, Yong-Jun Jang, and Kyung-Soo Yang Floquet stability analysis has been carried out to detect the onset of the secondary instability in the laminar flow past two identical square cylinders in tandem. Presence of a neighbouring cylinder alters flow topology, leading to change of stability characteristics. A parametric study has been pe ... [Phys. Fluids 24, 024102 (2012)] published Wed Feb 8, 2012.

Description: Tatsuya Yamada and Keiji Sakai We measured the viscosity and surface tension of various liquids under large (~10 s) shear deformation. Oscillation of a 10-[mu]m size microdroplet is brought about by the head-on collision of two droplets. Since the Reynolds number is as small as 100, the motion of the liquid is stable and the dyna ... [Phys. Fluids 24, 022103 (2012)] published Wed Feb 8, 2012.

Description: This paper presents a signal processing technique to improve angular rate accuracy of the gyroscope by combining the outputs of an array of MEMS gyroscope. A mathematical model for the accuracy improvement was described and a Kalman filter (KF) was designed to obtain optimal rate estimates. Especially, the rate signal was modeled by a first-order Markov process instead of a random walk to improve overall performance. The accuracy of the combined rate signal and affecting factors were analyzed using a steady-state covariance. A system comprising a six-gyroscope array was developed to test the presented KF. Experimental tests proved that the presented model was effective at improving the gyroscope accuracy. The experimental results indicated that six identical gyroscopes with an ARW noise of 6.2 °/Öh and a bias drift of 54.14 °/h could be combined into a rate signal with an ARW noise of 1.8 °/Öh and a bias drift of 16.3 °/h, while the estimated rate signal by the random walk model has an ARW noise of 2.4 °/Öh and a bias drift of 20.6 °/h. It revealed that both models could improve the angular rate accuracy and have a similar performance in static condition. In dynamic condition, the test results showed that the first-order Markov process model could reduce the dynamic errors 20% more than the random walk model.

Description: Because of their small size, passive nature, immunity to electromagnetic interference, and capability to directly measure physical parameters such as temperature and strain, fiber Bragg grating sensors have developed beyond a laboratory curiosity and are becoming a mainstream sensing technology. Recently, high temperature stable gratings based on regeneration techniques and femtosecond infrared laser processing have shown promise for use in extreme environments such as high temperature, pressure or ionizing radiation. Such gratings are ideally suited for energy production applications where there is a requirement for advanced energy system instrumentation and controls that are operable in harsh environments. This paper will present a review of some of the more recent developments.

Description: Methodologies and algorithms are presented for the secure cooperation of a team of autonomous mobile underwater sensors, connected through an acoustic communication network, within surveillance and patrolling applications. In particular, the work proposes a cooperative algorithm in which the mobile underwater sensors (installed on Autonomous Underwater Vehicles—AUVs) respond to simple local rules based on the available information to perform the mission and maintain the communication link with the network (behavioral approach). The algorithm is intrinsically robust: with loss of communication among the vehicles the coverage performance (i.e., the mission goal) is degraded but not lost. The ensuing form of graceful degradation provides also a reactive measure against Denial of Service. The cooperative algorithm relies on the fact that the available information from the other sensors, though not necessarily complete, is trustworthy. To ensure trustworthiness, a security suite has been designed, specifically oriented to the underwater scenario, and in particular with the goal of reducing the communication overhead introduced by security in terms of number and size of messages. The paper gives implementation details on the integration between the security suite and the cooperative algorithm and provides statistics on the performance of the system as collected during the UAN project sea trial held in Trondheim, Norway, in May 2011.

Description: The mean shift algorithm has achieved considerable success in target tracking due to its simplicity and robustness. However, the lack of spatial information may result in its failure to get high tracking precision. This might be even worse when the target is scale variant and the sequences are gray-levels. This paper presents a novel multiple subtemplates based tracking algorithm for the terminal guidance application. By applying a separate tracker to each subtemplate, it can handle more complicated situations such as rotation, scaling, and partial coverage of the target. The innovations include: (1) an optimal subtemplates selection algorithm is designed, which ensures that the selected subtemplates maximally represent the information of the entire template while having the least mutual redundancy; (2) based on the serial tracking results and the spatial constraint prior to those subtemplates, a Gaussian weighted voting method is proposed to locate the target center; (3) the optimal scale factor is determined by maximizing the voting results among the scale searching layers, which avoids the complicated threshold setting problem. Experiments on some videos with static scenes show that the proposed method greatly improves the tracking accuracy compared to the original mean shift algorithm.

Description: Hand-held near-infrared (NIR) optical imagers are developed by various researchers towards non-invasive clinical breast imaging. Unlike these existing imagers that can perform only reflectance imaging, a generation-2 (Gen-2) hand-held optical imager has been recently developed to perform both reflectance and transillumination imaging. The unique forked design of the hand-held probe head(s) allows for reflectance imaging (as in ultrasound) and transillumination or compressed imaging (as in X-ray mammography). Phantom studies were performed to demonstrate two-dimensional (2D) target detection via reflectance and transillumination imaging at various target depths (1–5 cm deep) and using simultaneous multiple point illumination approach. It was observed that 0.45 cc targets were detected up to 5 cm deep during transillumination, but limited to 2.5 cm deep during reflectance imaging. Additionally, implementing appropriate data post-processing techniques along with a polynomial fitting approach, to plot 2D surface contours of the detected signal, yields distinct target detectability and localization. The ability of the gen-2 imager to perform both reflectance and transillumination imaging allows its direct comparison to ultrasound and X-ray mammography results, respectively, in future clinical breast imaging studies.

Description: Studies on fault detection and diagnosis of planetary gearboxes are quite limited compared with those of fixed-axis gearboxes. Different from fixed-axis gearboxes, planetary gearboxes exhibit unique behaviors, which invalidate fault diagnosis methods that work well for fixed-axis gearboxes. It is a fact that for systems as complex as planetary gearboxes, multiple sensors mounted on different locations provide complementary information on the health condition of the systems. On this basis, a fault detection method based on multi-sensor data fusion is introduced in this paper. In this method, two features developed for planetary gearboxes are used to characterize the gear health conditions, and an adaptive neuro-fuzzy inference system (ANFIS) is utilized to fuse all features from different sensors. In order to demonstrate the effectiveness of the proposed method, experiments are carried out on a planetary gearbox test rig, on which multiple accelerometers are mounted for data collection. The comparisons between the proposed method and the methods based on individual sensors show that the former achieves much higher accuracies in detecting planetary gearbox faults.

Description: There have been only few studies to substantiate the kinematic characteristics of cursor movement. In this study, a quantitative experimental research method was used to explore the effect of moving direction on the kinematics of cursor movement in 24 typical young persons using our previously developed computerized measuring program. The results of multiple one way repeated measures ANOVAs and post hoc LSD tests demonstrated that the moving direction had effects on average velocity, movement time, movement unit and peak velocity. Moving leftward showed better efficiency than moving rightward, upward and downward from the kinematic evidences such as velocity, movement unit and time. Moreover, the unique pattern of the power spectral density (PSD) of velocity (strategy for power application) explained why the smoothness was still maintained while moving leftward even under an unstable situation with larger momentum. Moreover, the information from this cursor moving study can guide us to relocate the toolbars and icons in the window interface, especially for individuals with physical disabilities whose performances are easily interrupted while controlling the cursor in specific directions.

Description: We present a study of an electrical model of electromechanically active carbon-polymer composite (CPC) with carbide-derived carbon (CDC) electrodes. The major focus is on investigation of surface electrode behavior upon external bending of the material. We show that electrical impedance measured from the surface of the CDC-based CPC can be used to determine the curvature of the material and, hence, the tip displacement of a CPC laminate in a cantilever configuration. It is also shown that by measuring surface signals in the process of an actuator’s work-cycle, we obtain a self-sensing collision-detecting CPC actuator that can be considered as a counterpart of biomimetic vibrissae.

Description: In Underwater Wireless Sensor Networks (UWSNs), localization is one of most important technologies since it plays a critical role in many applications. Motivated by widespread adoption of localization, in this paper, we present a comprehensive survey of localization algorithms. First, we classify localization algorithms into three categories based on sensor nodes’ mobility: stationary localization algorithms, mobile localization algorithms and hybrid localization algorithms. Moreover, we compare the localization algorithms in detail and analyze future research directions of localization algorithms in UWSNs.

Description: This paper describes the characteristics of optical fiber sensors with surface plasmon resonance (SPR) at 1,310 nm in which the scattering loss of silica optical fiber is low. SPR operation in the infrared wavelength range is achieved by coating a thin tantalum pentaoxide (Ta2O5) film. The novelty of this paper lies in the verification of how the hetero-core scheme could be operated as a commercial base candidate in the sense of easy fabrication, sufficient mechanical strength, and significant sensitivity as a liquid detector under the basis of a low loss transmission network in the near infrared wavelength region. The effect of Ta2O5 layer thickness has been experimentally revealed in the wavelength region extending to 1,800 nm by using the hetero-core structured optical fiber. SPR characterizations have been made in the wavelength region 1,000–1,300 nm, showing the feasible operation at the near infrared wavelength and the possible practical applications. In addition, the technique developed in this work has been interestingly applied to a multi-point water-detection and a water-level gauge in which tandem-connected SPR sensors system using hetero-core structured fibers were incorporated. The detailed performance characteristics are also shown on these applications.

Description: Wireless Sensor Networks (WSNs) are gaining tremendous importance thanks to their broad range of commercial applications such as in smart home automation, health-care and industrial automation. In these applications multi-vendor and heterogeneous sensor nodes are deployed. Due to strict administrative control over the specific WSN domains, communication barriers, conflicting goals and the economic interests of different WSN sensor node vendors, it is difficult to introduce a large scale federated WSN. By allowing heterogeneous sensor nodes in WSNs to coexist on a shared physical sensor substrate, virtualization in sensor network may provide flexibility, cost effective solutions, promote diversity, ensure security and increase manageability. This paper surveys the novel approach of using the large scale federated WSN resources in a sensor virtualization environment. Our focus in this paper is to introduce a few design goals, the challenges and opportunities of research in the field of sensor network virtualization as well as to illustrate a current status of research in this field. This paper also presents a wide array of state-of-the art projects related to sensor network virtualization.

Description: C. Vannozzi Dip coating in the presence of a substrate-liquid interaction potential normal to the substrate, previously theoretically investigated by R. Krechetnikov and G. M. Homsy [Phys. Fluids 17, 038101 (2005)], was revisited. Their solution procedure leads to predictions of the entrained film thickness h t ... [Phys. Fluids 24, 022107 (2012)] published Thu Feb 16, 2012.

Description: Gait analysis using wearable sensors is an inexpensive, convenient, and efficient manner of providing useful information for multiple health-related applications. As a clinical tool applied in the rehabilitation and diagnosis of medical conditions and sport activities, gait analysis using wearable sensors shows great prospects. The current paper reviews available wearable sensors and ambulatory gait analysis methods based on the various wearable sensors. After an introduction of the gait phases, the principles and features of wearable sensors used in gait analysis are provided. The gait analysis methods based on wearable sensors is divided into gait kinematics, gait kinetics, and electromyography. Studies on the current methods are reviewed, and applications in sports, rehabilitation, and clinical diagnosis are summarized separately. With the development of sensor technology and the analysis method, gait analysis using wearable sensors is expected to play an increasingly important role in clinical applications.

Description: During the last years, proteomics has facilitated biomarker discovery by coupling high-throughput techniques with novel nanosensors. In the present review, we focus on the study of label-based and label-free detection systems, as well as nanotechnology approaches, indicating their advantages and applications in biomarker discovery. In addition, several disease biomarkers are shown in order to display the clinical importance of the improvement of sensitivity and selectivity by using nanoproteomics approaches as novel sensors.

Description: The photoplethysmographic waveform sits at the core of the most used, and arguably the most important, clinical monitor, the pulse oximeter.  Interestingly, the pulse oximeter was discovered while examining an artifact during the development of a noninvasive cardiac output monitor.  This article will explore the response of the pulse oximeter waveform to various modes of ventilation.  Modern digital signal processing is allowing for a re-examination of this ubiquitous signal. The effect of ventilation on the photoplethysmographic waveform has long been thought of as a source of artifact. The primary goal of this article is to improve the understanding of the underlying physiology responsible for the observed phenomena, thereby encouraging the utilization of this understanding to develop new methods of patient monitoring. The reader will be presented with a review of respiratory physiology followed by numerous examples of the impact of ventilation on the photoplethysmographic waveform.

Description: For decades, underwater acoustic communication has been restricted to the point-to-point long distance applications such as deep sea probes and offshore oil fields. For this reason, previous acoustic modems were typically characterized by high data rates and long working ranges at the expense of large size and high power consumption. Recently, as the need for underwater wireless sensor networks (UWSNs) has increased, the research and development of compact and low-power consuming communication devices has become the focus. From the consideration that the requisites of acoustic modems for UWSNs are low power consumption, omni-directional beam pattern, low cost and so on, in this paper, we design and implement an omni-directional underwater acoustic micro-modem satisfying these requirements. In order to execute fast digital domain signal processing and support flexible interfaces with other peripherals, an ARM Cortex-M3 is embedded in the micro-modem. Also, for the realization of small and omni-directional properties, a spherical transducer having a resonant frequency of 70 kHz and a diameter of 34 mm is utilized for the implementation. Physical layer frame format and symbol structure for efficient packet-based underwater communication systems are also investigated. The developed acoustic micro-modem is verified analytically and experimentally in indoor and outdoor environments in terms of functionality and performance. Since the modem satisfies the requirements for use in UWSNs, it could be deployed in a wide range of applications requiring underwater acoustic communication.

Description: This study examines an analog circuit comprising a multilayer perceptron neural network (MLPNN). This study proposes a low-power and small-area analog MLP circuit to implement in an E-nose as a classifier, such that the E-nose would be relatively small, power-efficient, and portable. The analog MLP circuit had only four input neurons, four hidden neurons, and one output neuron. The circuit was designed and fabricated using a 0.18 μm standard CMOS process with a 1.8 V supply. The power consumption was 0.553 mW, and the area was approximately 1.36 × 1.36 mm2. The chip measurements showed that this MLPNN successfully identified the fruit odors of bananas, lemons, and lychees with 91.7% accuracy.

Description: We present a novel system for detection, localization and tracking of multiple people, which fuses a multi-view computer vision approach with a radio-based localization system. The proposed fusion combines the best of both worlds, excellent computer-vision-based localization, and strong identity information provided by the radio system, and is therefore able to perform tracking by identification, which makes it impervious to propagated identity switches. We present comprehensive methodology for evaluation of systems that perform person localization in world coordinate system and use it to evaluate the proposed system as well as its components. Experimental results on a challenging indoor dataset, which involves multiple people walking around a realistically cluttered room, confirm that proposed fusion of both systems significantly outperforms its individual components. Compared to the radio-based system, it achieves better localization results, while at the same time it successfully prevents propagation of identity switches that occur in pure computer-vision-based tracking.

Description: Measuring bone turnover markers could detect early stages of osteoporosis and early responses to anti-osteoporotic treatments. Currently, commonly used bone turnover markers, N-telopeptides (NTx) and C-telopeptides (CTx), are measured using ELISA tests, which demands time and increases cost. Bone turnover markers need to be measured more easily for general use. Lateral flow-based immunoassay would be an appropriate method for this context. This study was performed to investigate the precision of a newly developed lateral flow-based immunoassay for measuring the urinary NTx and serum CTx, and their correlations with ELISA measurements. Urine NTx and serum CTx concentrations were determined by photoscan of newly developed strips, using a lateral flow-based immunoassay for 36 subjects (mean age 66.2 years, SD 7.5 years; four males and 32 females). Repeated measurement of urinary NTx and serum CTx were performed three times, using this technology for a precision test. The correlation of the lateral flow-based immunoassay with the ELISA measurements was analyzed. Precision of the newly developed lateral flow based immunoassay was 0.974 (ICC, 95% confidence interval, 0.955 to 0.986) and 0.995 (ICC, 95% confidence interval, 0.991 to 0.997) for urinary NTx and serum CTx, respectively. The correlation of lateral flow based immunoassay with ELISA was 0.913 for urinary NTx and 0.872 for serum CTx. These results suggest that measuring the urinary NTx and serum CTx, using a lateral flow-based immunoassay, is a relevant method for point-of-care testing and screening of bone resorption markers.

Description: To enhance the control performance of permanent magnet synchronous motors (PMSMs), a generalized predictive control (GPC)-based proportional integral feedforward (PIF) controller is proposed for the speed control system. In this new approach, firstly, based on the online identification of controlled model parameters, a simplified GPC law supplies the PIF controller with suitable control parameters according to the uncertainties in the operating conditions. Secondly, the speed reference curve for PMSMs is usually required to be continuous and continuously differentiable according to the general servo system design requirements, so the adaptation of the speed reference is discussed in details in this paper. Hence, the performance of the speed control system using a GPC-based PIF controller is improved for tracking some specified signals. The main motivation of this paper is the extension of GPC law to replace the traditional PI or PIF controllers in industrial applications. The efficacy and usefulness of the proposed controller are verified through experimental results.

Description: Wine quality is related to its intrinsic visual, taste, or aroma characteristics and is reflected in the price paid for that wine. One of the most important wine faults is the excessive concentration of acetic acid which can cause a wine to take on vinegar aromas and reduce its varietal character. Thereby it is very important for the wine industry to have methods, like electronic noses, for real-time monitoring the excessive concentration of acetic acid in wines. However, aroma characterization of alcoholic beverages with sensor array electronic noses is a difficult challenge due to the masking effect of ethanol. In this work, in order to detect the presence of acetic acid in synthetic wine samples (aqueous ethanol solution at 10% v/v) we use a detection unit which consists of a commercial electronic nose and a HSS32 auto sampler, in combination with a neural network classifier (MLP). To find the characteristic vector representative of the sample that we want to classify, first we select the sensors, and the section of the sensors response curves, where the probability of detecting the presence of acetic acid will be higher, and then we apply Principal Component Analysis (PCA) such that each sensor response curve is represented by the coefficients of its first principal components. Results show that the PEN3 electronic nose is able to detect and discriminate wine samples doped with acetic acid in concentrations equal or greater than 2 g/L.

Description: Olivier Marsden, Christophe Bogey, and Christophe Bailly The focus of this work is the study of the asymmetric mean flow which can appear inside shallow cavities of circular planform, and for which limited experimental data is available. To this end, the behaviour of cylindrical cavities in grazing flow is investigated numerically, for varying ratios of d ... [Phys. Fluids 24, 125107 (2012)] published Thu Dec 27, 2012.

Description: Weiwei Zhang, Xiaobo Liu, Jian Zhai, and Zhengyin Ye Slender bodies of revolution placed at high angles of attack will produce a steady asymmetric vortex pair. This behavior is determined by the spatial instability of the flow. The asymmetric vortex pair is very sensitive to small disturbances near the tip. This paper presents a simple side force alle ... [Phys. Fluids 24, 124105 (2012)] published Thu Dec 27, 2012.

Description: S. Zuccher, M. Caliari, A. W. Baggaley, and C. F. Barenghi We study reconnections of quantum vortices by numerically solving the governing Gross-Pitaevskii equation. We find that the minimum distance between vortices scales differently with time before and after the vortex reconnection. We also compute vortex reconnections using the Biot-Savart law for vort ... [Phys. Fluids 24, 125108 (2012)] published Thu Dec 27, 2012.

Description: Haecheon Choi, Hyungmin Park, Woong Sagong, and Sang-im Lee Despite the long history of biomimetics (or biomimetic engineering), a scientific discipline of implementing nature-inspired ideas to engineering systems for their performance enhancement, successful developments have been made only recently, especially in the field of flow control. In the present p ... [Phys. Fluids 24, 121302 (2012)] published Thu Dec 27, 2012.

Description: J. E. Sprittles and Y. D. Shikhmurzaev The process of coalescence of two identical liquid drops is simulated numerically in the framework of two essentially different mathematical models, and the results are compared with experimental data on the very early stages of the coalescence process reported recently. The first model tested is th ... [Phys. Fluids 24, 122105 (2012)] published Thu Dec 27, 2012.

Description: Perfumes are manufactured by mixing odorous materials with different volatilities. The parameter that measures the lasting property of a material when applied on the skin is called substantivity or tenacity. It is well known by perfumers that citrus and green notes are perceived as fresh and they tend to evaporate quickly, while odors most dissimilar to ‘fresh’ (e.g., oriental, powdery, erogenic and animalic scents) are tenacious. However, studies aimed at quantifying the relationship between fresh odor quality and substantivity have not received much attention. In this work, perceptual olfactory ratings on a fresh scale, estimated in a previous study, were compared with substantivity parameters and antierogenic ratings from the literature. It was found that the correlation between fresh odor character and odorant substantivity is quite strong (r = −0.85). ‘Fresh’ is sometimes interpreted in perfumery as ‘cool’ and the opposite of ‘warm’. This association suggests that odor freshness might be somehow related to temperature. Assuming that odor perception space was shaped throughout evolution in temperate climates, results reported here are consistent with the hypothesis that ‘fresh’ evokes scents typically encountered in the cool season, while ‘warm’ would be evoked by odors found in nature during summer. This hypothesis is rather simplistic but it may provide a new insight to better understand the perceptual space of scents.

Description: A new electronic tongue to monitor the presence of glyphosate (a non-selective systemic herbicide) has been developed. It is based on pulse voltammetry and consists in an array of three working electrodes (Pt, Co and Cu) encapsulated on a methacrylate cylinder. The electrochemical response of the sensing array was characteristic of the presence of glyphosate in buffered water (phosphate buffer 0.1 mol·dm−3, pH 6.7). Rotating disc electrode (RDE) studies were carried out with Pt, Co and Cu electrodes in water at room temperature and at pH 6.7 using 0.1 mol·dm−3 of phosphate as a buffer. In the presence of glyphosate, the corrosion current of the Cu and Co electrodes increased significantly, probably due to the formation of Cu2+ or Co2+ complexes. The pulse array waveform for the voltammetric tongue was designed by taking into account some of the redox processes observed in the electrochemical studies. The PCA statistical analysis required four dimensions to explain 95% of variance. Moreover, a two-dimensional representation of the two principal components differentiated the water mixtures containing glyphosate. Furthermore, the PLS statistical analyses allowed the creation of a model to correlate the electrochemical response of the electrodes with glyphosate concentrations, even in the presence of potential interferents such as humic acids and Ca2+. The system offers a PLS prediction model for glyphosate detection with values of 098, −2.3 × 10−5 and 0.94 for the slope, the intercept and the regression coefficient, respectively, which is in agreement with the good fit between the predicted and measured concentrations. The results suggest the feasibility of this system to help develop electronic tongues for glyphosate detection.

Description: Daisuke Seki and Masaharu Matsubara A hot-wire measurement was conducted in a planar channel flow that originated from a strongly disturbed flow in an entrance channel followed by an expansion channel used to reduce the Reynolds number (Re). From ceasing decrease of the streamwise velocity fluctuation energy and the linear extrapolati ... [Phys. Fluids 24, 124102 (2012)] published Thu Dec 20, 2012.

Description: Diego A. Donzis The structure of a shock wave interacting with isotropic turbulence is investigated. General principles of similarity scaling show that consistency with known physical limiting behavior requires incomplete similarity solutions where the governing non-dimensional parameters, namely, the Reynolds, con ... [Phys. Fluids 24, 126101 (2012)] published Thu Dec 20, 2012.

Description: Md. Mamun Molla, Bing-Chen Wang, and David C. S. Kuhn In this research, we numerically investigate the physics of pulsatile flows confined within a 3-dimensional channel with a modelled stenosis formed eccentrically on the upper wall using the method of large-eddy simulation (LES). An advanced dynamic nonlinear subgrid-scale stress model was utilized t ... [Phys. Fluids 24, 121901 (2012)] published Thu Dec 20, 2012.

Description: Monitoring tropical deforestation and forest degradation is one of the central elements for the Reduced Emissions from Deforestation and Forest Degradation in developing countries (REDD+) scheme. Current arrangements for monitoring are based on remote sensing and field measurements. Since monitoring is the periodic process of assessing forest stands properties with respect to reference data, adopting the current REDD+ requirements for implementing monitoring at national levels is a challenging task. Recently, the advancement in Information and Communications Technologies (ICT) and mobile devices has enabled local communities to monitor their forest in a basic resource setting such as no or slow internet connection link, limited power supply, etc. Despite the potential, the use of mobile device system for community based monitoring (CBM) is still exceptional and faces implementation challenges. This paper presents an integrated data collection system based on mobile devices that streamlines the community-based forest monitoring data collection, transmission and visualization process. This paper also assesses the accuracy and reliability of CBM data and proposes a way to fit them into national REDD+ Monitoring, Reporting and Verification (MRV) scheme. The system performance is evaluated at Tra Bui commune, Quang Nam province, Central Vietnam, where forest carbon and change activities were tracked. The results show that the local community is able to provide data with accuracy comparable to expert measurements (index of agreement greater than 0.88), but against lower costs. Furthermore, the results confirm that communities are more effective to monitor small scale forest degradation due to subsistence fuel wood collection and selective logging, than high resolution remote sensing SPOT imagery.

Description: Tim Reis and Paul J. Dellar We present lattice Boltzmann simulations of rarefied flows driven by pressure drops along two-dimensional microchannels. Rarefied effects lead to non-zero cross-channel velocities, and nonlinear variations in the pressure along the channel. Both effects are absent in flows driven by uniform body for ... [Phys. Fluids 24, 112001 (2012)] published Thu Nov 8, 2012.

Description: Long Chau and Kiran Bhaganagar Direct numerical simulation is used to understand the flow over ripple-shaped random rough elements. The random roughness has been generated using the model for sand ripples consisting of saltation, creep and suspension processes. A set of metrics based on both the geometrical and statistical proper ... [Phys. Fluids 24, 115102 (2012)] published Thu Nov 8, 2012.

Description: Daniel Tudball-Smith, Justin S. Leontini, John Sheridan, and David Lo Jacono The modification of a cylinder wake by streamwise oscillation of the cylinder at the vortex shedding frequency of the unperturbed cylinder is reported. Recent numerical simulations [J. S. Leontini, D. Lo Jacono, and M. C. Thompson, A numerical study of an inline oscillating cylinder in a free stream ... [Phys. Fluids 24, 111703 (2012)] published Tue Nov 13, 2012.

Description: Mitsuhiro Ohta and Mark Sussman The buoyancy-driven motion of a single skirted bubble or drop rising through a viscous liquid is computationally explored by way of 3d-axisymmetric computations. The Navier-Stokes equations for incompressible two-fluid flow are solved numerically in which the coupled level-set and volume-of-fluid me ... [Phys. Fluids 24, 112101 (2012)] published Mon Nov 12, 2012.

Description: L. Li, M. D. Patterson, K. Zhang, and R. R. Kerswell The spin-up and spin-down of a fluid in a rapidly rotating, fluid-filled, and closed half cone are studied both numerically and experimentally. This unusual set up is of interest because it represents a pathological case for the classical linear theory of Greenspan and Howard [J. Fluid Mech. 17, 385 ... [Phys. Fluids 24, 116601 (2012)] published Mon Nov 12, 2012.

Description: Mario F. Trujillo and Steven R. Lewis Simulations of droplet train impingement on a pre-wetted solid surface heated from below are used to study the thermal boundary layer behavior over a parameter space which includes variations in Reynolds, Peclet, and Weber numbers, as well as variations in inter-droplet spacing and initial liquid fi ... [Phys. Fluids 24, 112102 (2012)] published Mon Nov 12, 2012.

Description: Chiu-On Ng and Qi Zhou An analysis using the lubrication approximation is performed for the dispersion of a neutral non-reacting solute due to electro-osmotic flow through a circular channel under the combined effects of longitudinal non-uniformity of potential and hydrodynamic slippage on the channel wall. The wall is pe ... [Phys. Fluids 24, 112002 (2012)] published Mon Nov 12, 2012.

Description: Mohamed A. Samaha, Hooman Vahedi Tafreshi, and Mohamed Gad-el-Hak Prior studies have demonstrated that superhydrophobicity of submerged surfaces is influenced by hydrostatic pressure and other environmental effects. Sustainability of a superhydrophobic surface could be characterized by both how long it maintains the trapped air in its surface pores, so-called long ... [Phys. Fluids 24, 112103 (2012)] published Mon Nov 12, 2012.

Description: Nowadays, optical sensors are used to digitize sculptural artworks by exploiting various contactless technologies. Cultural Heritage applications may concern 3D reconstructions of sculptural shapes distinguished by small details distributed over large surfaces. These applications require robust multi-view procedures based on aligning several high resolution 3D measurements. In this paper, the integration of a 3D structured light scanner and a stereo photogrammetric sensor is proposed with the aim of reliably reconstructing large free form artworks. The structured light scanner provides high resolution range maps captured from different views. The stereo photogrammetric sensor measures the spatial location of each view by tracking a marker frame integral to the optical scanner. This procedure allows the computation of the rotation-translation matrix to transpose the range maps from local view coordinate systems to a unique global reference system defined by the stereo photogrammetric sensor. The artwork reconstructions can be further augmented by referring metadata related to restoration processes. In this paper, a methodology has been developed to map metadata to 3D models by capturing spatial references using a passive stereo-photogrammetric sensor. The multi-sensor framework has been experienced through the 3D reconstruction of a Statue of Hope located at the English Cemetery in Florence. This sculptural artwork has been a severe test due to the non-cooperative environment and the complex shape features distributed over a large surface.

Description: Appliance Load Monitoring (ALM) is essential for energy management solutions, allowing them to obtain appliance-specific energy consumption statistics that can further be used to devise load scheduling strategies for optimal energy utilization. Fine-grained energy monitoring can be achieved by deploying smart power outlets on every device of interest; however it incurs extra hardware cost and installation complexity. Non-Intrusive Load Monitoring (NILM) is an attractive method for energy disaggregation, as it can discern devices from the aggregated data acquired from a single point of measurement. This paper provides a comprehensive overview of NILM system and its associated methods and techniques used for disaggregated energy sensing. We review the state-of-the art load signatures and disaggregation algorithms used for appliance recognition and highlight challenges and future research directions.

Description:  A variety of microrobots have commonly been used in the fields of biomedical engineering and underwater operations during the last few years. Thanks to their compact structure, low driving power, and simple control systems, microrobots can complete a variety of underwater tasks, even in limited spaces. To accomplish our objectives, we previously designed several bio-inspired underwater microrobots with compact structure, flexibility, and multi-functionality, using ionic polymer metal composite (IPMC) actuators. To implement high-position precision for IPMC legs, in the present research, we proposed an electromechanical model of an IPMC actuator and analysed the deformation and actuating force of an equivalent IPMC cantilever beam, which could be used to design biomimetic legs, fingers, or fins for an underwater microrobot. We then evaluated the tip displacement of an IPMC actuator experimentally. The experimental deflections fit the theoretical values very well when the driving frequency was larger than 1 Hz. To realise the necessary multi-functionality for adapting to complex underwater environments, we introduced a walking biomimetic microrobot with two kinds of motion attitudes: a lying state and a standing state. The microrobot uses eleven IPMC actuators to move and two shape memory alloy (SMA) actuators to change its motion attitude. In the lying state, the microrobot implements stick-insect-inspired walking/rotating motion, fish-like swimming motion, horizontal grasping motion, and floating motion. In the standing state, it implements inchworm-inspired crawling motion in two horizontal directions and grasping motion in the vertical direction. We constructed a prototype of this biomimetic microrobot and evaluated its walking, rotating, and floating speeds experimentally. The experimental results indicated that the robot could attain a maximum walking speed of 3.6 mm/s, a maximum rotational speed of 9°/s, and a maximum floating speed of 7.14 mm/s. Obstacle-avoidance and swimming experiments were also carried out to demonstrate its multi-functionality.

Description: An infrared ceiling sensor network system is reported in this study to realize behavior analysis and fall detection of a single person in the home environment. The sensors output multiple binary sequences from which we know the existence/non-existence of persons under the sensors. The short duration averages of the binary responses are shown to be able to be regarded as pixel values of a top-view camera, but more advantageous in the sense of preserving privacy. Using the “pixel values” as features, support vector machine classifiers succeeded in recognizing eight activities (walking, reading, etc.) performed by five subjects at an average recognition rate of 80.65%. In addition, we proposed a martingale framework for detecting falls in this system. The experimental results showed that we attained the best performance of 95.14% (F1 value), the FAR of 7.5% and the FRR of 2.0%. This accuracy is not sufficient in general but surprisingly high with such low-level information. In summary, it is shown that this system has the potential to be used in the home environment to provide personalized services and to detect abnormalities of elders who live alone.

Description: The overall aim of our research is to develop a monitoring system for neonatal intensive care units. Long-term EEG monitoring in newborns require that the electrodes don’t harm the sensitive skin of the baby, an especially relevant feature for premature babies. Our approach to EEG monitoring is based on several electrodes distributed over the head of the baby, and since the weight of the head always will be on some of them, any type of hard electrode will inevitably cause a pressure-point that can irritate the skin. Therefore, we propose the use of soft conductive textiles as EEG electrodes, primarily for neonates, but also for other kinds of unobtrusive long-term monitoring. In this paper we have tested two types of textile electrodes on five healthy adults and compared them to standard high quality electrodes. The acquired signals were compared with respect to morphology, frequency distribution, spectral coherence, correlation and power line interference sensitivity, and the signals were found to be similar in most respects. The good measurement performance exhibited by the textile electrodes indicates that they are feasible candidates for EEG recording, opening the door for long-term EEG monitoring applications.

Description: K. Alba, S. M. Taghavi, and I. A. Frigaard We study density-stable laminar miscible displacement flow of two iso-viscous Newtonian fluids in an inclined pipe (diameter D-hat). We present a wide range of novel experimental results. We illustrate the non-monotone relation in displacement efficiency at the density difference moves from positive ... [Phys. Fluids 24, 123102 (2012)] published Tue Dec 11, 2012.

Description: M. Mishra, A. Thess, and A. De Wit Magnetic fields have been shown experimentally to modify convective dynamics developing around traveling chemical fronts in presence of unfavorable density gradients. To understand the conditions in which such magnetic fields affect autocatalytic fronts, we study theoretically the influence of a sim ... [Phys. Fluids 24, 124101 (2012)] published Thu Dec 6, 2012.

Description: Kyle Spyksma, Moriah Magcalas, and Natalie Campbell Isotropic hyperviscous turbulence is modelled with a pseudospectral Navier-Stokes model and comparisons are made with regular-viscosity isotropic turbulence. Two proposed means of measuring the (hyperviscous) turbulent Reynolds number are presented and critiqued, leading to a proposal for a hypervis ... [Phys. Fluids 24, 125102 (2012)] published Thu Dec 6, 2012.

Description: Tristan Gilet and John W. M. Bush We present the results of an experimental investigation of fluid drops impacting an inclined rigid surface covered with a thin layer of high viscosity fluid. We deduce the conditions under which droplet bouncing, splitting, and merger arise. Particular attention is given to rationalizing the observe ... [Phys. Fluids 24, 122103 (2012)] published Thu Dec 13, 2012.

Description: R. Thomas, C. Kharif, and M. Manna A nonlinear Schrodinger equation for the envelope of two dimensional surface water waves on finite depth with non-zero constant vorticity is derived, and the influence of this constant vorticity on the well-known stability properties of weakly nonlinear wave packets is studied. It is demonstrated th ... [Phys. Fluids 24, 127102 (2012)] published Thu Dec 13, 2012.

Description: In this paper, a laboratory goniometer system for performing multi-angular measurements under controlled illumination conditions is described. A commercially available robotic arm enables the acquisition of a large number of measurements over the full hemisphere within a short time span making it much faster than other goniometers. In addition, the presented set-up enables assessment of anisotropic reflectance and emittance behaviour of soils, leaves and small canopies. Mounting a spectrometer enables acquisition of either hemispherical measurements or measurements in the horizontal plane. Mounting a thermal camera allows directional observations of the thermal emittance. This paper also presents three showcases of these different measurement set-ups in order to illustrate its possibilities. Finally, suggestions for applying this instrument and for future research directions are given, including linking the measured reflectance anisotropy with physically-based anisotropy models on the one hand and combining them with field goniometry measurements for joint analysis with remote sensing data on the other hand. The speed and flexibility of the system offer a large added value to the existing pool of laboratory goniometers.

Description: Optical waveguide lightmode spectroscopy (OWLS) is usually applied as a biosensor system to the sorption-desorption of proteins to waveguide surfaces. Here, we show that OWLS can be used to monitor the quality of oxide thin film materials and of coatings of pulsed laser deposition synthesized CdSe quantum dots (QDs) intended for solar energy applications. In addition to changes in data treatment and experimental procedure, oxide- or QD-coated waveguide sensors must be synthesized. We synthesized zinc stannate (Zn2SnO4) coated (Si,Ti)O2 waveguide sensors, and used OWLS to monitor the relative mass of the film over time. Films lost mass over time, though at different rates due to variation in fluid flow and its physical effect on removal of film material. The Pulsed Laser Deposition (PLD) technique was used to deposit CdSe QD coatings on waveguides. Sensors exposed to pH 2 solution lost mass over time in an expected, roughly exponential manner. Sensors at pH 10, in contrast, were stable over time. Results were confirmed with atomic force microscopy imaging. Limiting factors in the use of OWLS in this manner include limitations on the annealing temperature that maybe used to synthesize the oxide film, and limitations on the thickness of the film to be studied. Nevertheless, the technique overcomes a number of difficulties in monitoring the quality of thin films in-situ in liquid environments.

Description: A sensitive flow injection chemiluminescence assay for carcinoembryonic antigen (CEA) detection based on signal amplification with gold nanoparticles (NPs) is reported in the present work. The sandwich system of CEA/anti-CEA/goat-anti-mouse IgG functionalized Au nanoparticles was used as the sensing platform. In order to improve detection sensitivity, a further gold enlargement step was developed based on the autocatalytic Au deposition of gold nanoprobes via the reduction of AuCl4− to Au0 on their surface in the presence of NH2OH·HCl. AuCl4−, which is a soluble product of gold nanoprobes, served as an analyte in the CL reaction for the indirect measurement of CEA. Under optimized conditions, the CL intensity of the system was linearly related to the logarithm of CEA concentration in the range of 100 pg∙mL−1 to 1,000 ng∙mL−1, with a detection limit of 20 pg∙mL−1.

Description: This paper considers the problem of designing power efficient routing with guaranteed delivery for sensor networks with unknown geographic locations. We propose HECTOR, a hybrid energy efficient tree-based optimized routing protocol, based on two sets of virtual coordinates. One set is based on rooted tree coordinates, and the other is based on hop distances toward several landmarks. In HECTOR, the node currently holding the packet forwards it to its neighbor that optimizes ratio of power cost over distance progress with landmark coordinates, among nodes that reduce landmark coordinates and do not increase distance in tree coordinates. If such a node does not exist, then forwarding is made to the neighbor that reduces tree-based distance only and optimizes power cost over tree distance progress ratio. We theoretically prove the packet delivery and propose an extension based on the use of multiple trees. Our simulations show the superiority of our algorithm over existing alternatives while guaranteeing delivery, and only up to 30% additional power compared to centralized shortest weighted path algorithm.

Description: Personalized medicine has the potential to improve our ability to maintain health and treat disease, while ameliorating continuously rising healthcare costs. Translation of basic research findings to clinical applications within regulatory compliance is required for personalized medicine to become the new foundation for practice of medicine. Deploying even a few of the thousands of potential diagnostic biomarkers identified each year as part of personalized treatment workflows requires clinically efficient biosensor technologies to monitor multiple biomarkers in patients in real time. This paper discusses a critical component of a regulatory system, a microcavity optical biosensor for label-free monitoring of biomolecular interactions at physiologically-relevant concentrations. While most current biosensor research focuses on improving sensitivity, this paper emphasizes other characteristics a biosensor technology requires to be practical in a clinical setting, presenting robust microcavity biosensors which are easy to manufacture and integrate with microfluidics into flexible and redesignable platforms making the microcavity biosensors deployable for continuous monitoring of biomarkers in body fluids in the clinic,  in dense 2D random arrays for high-throughput applications like drug-library screening in interactomics, and of the secretory behavior of single cells in the laboratory.

Description: In this work, a novel amperometric immunosensor based on multi-walled carbon nanotubes-thionine-chitosan (MWCNTs-THI-CHIT) nanocomposite film as electrode modified material was developed for the detection of chlorpyrifos residues. The nanocomposite film was dropped onto a glassy carbon electrode (GCE), and then the anti-chlorpyrifos monoclonal antibody was covalently immobilized onto the surface of MWCNTs-THI-CHIT/GCE using the crosslinking agent glutaraldehyde (GA). The modification procedure was characterized by using cyclic voltammetry (CV) and electrochemical impedance spectroscopy (EIS). Under the optimized conditions, a linear relationship between the relative change in peak current of different pulse voltammetry (DPV) and the logarithm of chlorpyrifos solution concentration was obtained in the range from 0.1 to 1.0 × 105 ng/mL with a detection limit of 0.046 ng/mL. The proposed chlorpyrifos immunosensor exhibited high reproducibility, stability, and good selectivity and regeneration, making it a potential alternative tool for ultrasensitive detection of chlorpyrifos residues in vegetables and fruits.

Description: The tracking of multiple wireless mobile nodes is not easy with current legacy WSN technologies, due to their inherent technical complexity, especially when heavy traffic and frequent movement of mobile nodes are encountered. To enable mobile asset tracking under these legacy WSN systems, it is necessary to design a specific system architecture that can manage numerous mobile nodes attached to mobile assets. In this paper, we present a practical system architecture including a communication protocol, a three-tier network, and server-side middleware for mobile asset tracking in legacy WSNs consisting of mobile-stationary co-existing infrastructures, and we prove the functionality of this architecture through careful evaluation in a test bed. Evaluation was carried out in a microwave anechoic chamber as well as on a straight road near our office. We evaluated communication mobility performance between mobile and stationary nodes, location-awareness performance, system stability under numerous mobile node conditions, and the successful packet transfer rate according to the speed of the mobile nodes. The results indicate that the proposed architecture is sufficiently robust for application in realistic mobile asset tracking services that require a large number of mobile nodes.

Description: G. E. Lau, G. H. Yeoh, V. Timchenko, and J. A. Reizes Large-eddy simulations examining natural convection in an enclosed cavity with the simultaneous presence of laminar, transitional, and turbulent flow regimes were conducted. The Rayleigh number based on height of the cavity is 4.6 x 10. Different dynamic global-coefficient procedures to compute th ... [Phys. Fluids 24, 094105 (2012)] published Fri Sep 21, 2012.

Description: Long term continuous monitoring of electrocardiogram (ECG) in a free living environment provides valuable information for prevention on the heart attack and other high risk diseases. This paper presents the design of a real-time wearable ECG monitoring system with associated cardiac arrhythmia classification algorithms. One of the striking advantages is that ECG analog front-end and on-node digital processing are designed to remove most of the noise and bias. In addition, the wearable sensor node is able to monitor the patient’s ECG and motion signal in an unobstructive way. To realize the real-time medical analysis, the ECG is digitalized and transmitted to a smart phone via Bluetooth. On the smart phone, the ECG waveform is visualized and a novel layered hidden Markov model is seamlessly integrated to classify multiple cardiac arrhythmias in real time. Experimental results demonstrate that the clean and reliable ECG waveform can be captured in multiple stressed conditions and the real-time classification on cardiac arrhythmia is competent to other workbenches.

Description: Monitoring the performance is a crucial task for elite sports during both training and competition. Velocity is the key parameter of performance in swimming, but swimming performance evaluation remains immature due to the complexities of measurements in water. The purpose of this study is to use a single inertial measurement unit (IMU) to estimate front crawl velocity. Thirty swimmers, equipped with an IMU on the sacrum, each performed four different velocity trials of 25 m in ascending order. A tethered speedometer was used as the velocity measurement reference. Deployment of biomechanical constraints of front crawl locomotion and change detection framework on acceleration signal paved the way for a drift-free integration of forward acceleration using IMU to estimate the swimmers velocity. A difference of 0.6 ± 5.4 cm·s−1 on mean cycle velocity and an RMS difference of 11.3 cm·s−1 in instantaneous velocity estimation were observed between IMU and the reference. The most important contribution of the study is a new practical tool for objective evaluation of swimming performance. A single body-worn IMU provides timely feedback for coaches and sport scientists without any complicated setup or restraining the swimmer’s natural technique.

Description: People interact with systems and applications through several devices and are willing to share information about preferences, interests and characteristics. Social networking profiles, data from advanced sensors attached to personal gadgets, and semantic web technologies such as FOAF and microformats are valuable sources of personal information that could provide a fair understanding of the user, but profile information is scattered over different user models. Some researchers in the ubiquitous user modeling community envision the need to share user model’s information from heterogeneous sources. In this paper, we address the syntactic and semantic heterogeneity of user models in order to enable user modeling interoperability. We present a dynamic user profile structure based in Simple Knowledge Organization for the Web (SKOS) to provide knowledge representation for ubiquitous user model. We propose a two-tier matching strategy for concept schemas alignment to enable user modeling interoperability. Our proposal is proved in the application scenario of sharing and reusing data in order to deal with overweight and obesity.

Description: A precision measurement finds its equatorial bulge somewhat smaller than expected and seemingly unaffected by the solar cycle.

Description: Internationalizing the science community, encouraging creativity, and becoming a world research leader are the aims of an initiative in a country better known for its industry than for its science.

Description: The GOP challenger would halt federal funding for technology commercialization. Both candidates have given short shrift to climate change.

Description: Emerging devices for measuring quantum phase offer a possible new window into phenomena far outside condensed-matter physics.

Description: John Kim This is a brief account of the 14th biennial Summer Program of the Center for Turbulence Research, which was held at Stanford University from June 25 to July 20, 2012. Key accomplishments achieved during the summer program were presented at the conclusion of the program, and a few highlights are rep ... [Phys. Fluids 24, 100501 (2012)] published Wed Oct 3, 2012.

Description: A. Bragg, D. C. Swailes, and R. Skartlien Continuum equations derived from a probability density function kinetic equation contain dispersion tensors that describe the interaction between inertial particles and the underlying turbulent flow in which they are transported. These tensors require closure treatment and recent work has shown that ... [Phys. Fluids 24, 103304 (2012)] published Fri Oct 12, 2012.

Description: Shih-Di Chen, Tsorng-Whay Pan, and Chien-Cheng Chang In this article, we investigate the motion of neutrally buoyant elliptical cylinders in plane Poiseuille flow of a Newtonian fluid. The method of distributed Lagrange multiplier/fictitious domain was used to solve the Navier-Stokes equations as well as for the motion of elliptical cylinders. The mot ... [Phys. Fluids 24, 103302 (2012)] published Fri Oct 12, 2012.

Description: M. J. Goldsworthy One of the most useful tools for modelling rarefied hypersonic flows is the Direct Simulation Monte Carlo (DSMC) method. Simulator particle movement and collision calculations are combined with statistical procedures to model thermal non-equilibrium flow-fields described by the Boltzmann equation. T ... [Phys. Fluids 24, 106102 (2012)] published Fri Oct 12, 2012.