Abstract
The fracture of polyethylene has been studied extensively using conventional testing geometries such as three-point bending (TPB) and single-edge notch tension (SENT). These geometries are of limited utility for studying crack growth, because the crack speed is constantly changing and the crack front is in the centre of the specimen. Double torsion (DT) is a fracture geometry that suffers neither of these disadvantages, yet has only received limited attention in the literature. Its use has been limited to highly brittle materials such as glass, ceramics, thermosetting plastics and PMMA. In contrast to these materials, high-density polyethylene (HDPE) is an inherently ductile polymer. Before the advantages of DT can be exploited for testing HDPE, it is first necessary to demonstrate the validity of DT fracture measurements performed on such a ductile material. In this paper it is shown that at moderate rates of loading and at temperatures below 0‡C, valid double torsion fracture results can be obtained for an ethylene 1-butene copolymer. A novel technique for specimen preparation and a simple method for accurately monitoring crack growth are also described.
Similar content being viewed by others
References
M. K. V. Chan and J. G. Williams, Int. J. Fract. 22 (1983) 145.
M. K. V. Chan and J. G. Williams, Polymer 24 (1983) 234.
X. Lu, X. Wang and N. Brown, J. Mater. Sci. 23 (1988) 643.
D. Barry and O. Delatycki, J. Polym. Sci. B Polym. Phys. Ed. 25 (1987) 883.
I. Narisawa, Polym. Eng. Sci. 27 (1987) 41.
X. Lu and N. Brown, Polymer 28 (1987) 1505.
D. B. Barry and O. Delatycki, J. Appl. Polym. Sci. 38 (1989) 339.
N. Brown and S. K. Bhattacharya, J. Mater. Sci. 20 (1985) 4553.
S. H. Carr, B. Crist and T. J. Marks, Gov. Rep. Announce. Index 85 (1985) 96.
K. Tonyali, C. Rogers and H. R. Brown, J. Macromol. Sci. Phys. B28 (1989) 235.
N. Brown, J. Donofrio and X. Lu, Polymer 28 (1987) 1326.
M. Flei\ner, Kunststoffe 77 (1987) 1.
D. J. Gerry, PhD thesis, University of Vermont (1966).
J. A. Kies and B. J. Clark, in “Proceedings of the 2nd International Conference on Fracture”, Brighton, April 1969, edited by P. L. Pratt (Chapman and Hall, London, 1969) p. 483.
J.-C. Pollet and S. J. Burns, “Evaluation for ASTM E-24.07.02” (American Society for Testing and Materials, Philadelphia, PA, 1979).
F. P. Champomier, in “Fracture Mechanics Applied to Brittle Materials”, ASTM STP 678, edited by S. W. Freiman (American Society for Testing and Materials, Philadelphia, PA, 1979) p. 60.
T. A. Michalske, M. Singh and V. D. Frechette, in “Fracture Mechanics Methods for Ceramics, Rocks, and Concrete”, ASTM STP 745, edited by S. W. Freiman and E. R. Fuller (American Society for Testing and Materials, Philadelphia, PA, 1981) p. 3.
J. O. Outwater, M. C. Murphy, R. G. Kumble and J. T. Berry, in “Fracture Toughness and Slow-Stable Cracking”, ASTM STP 559 (Americal Society for Testing and Materials, Philadelphia, PA, 1974) p. 127.
A. G. Evans, M. Linzer and L. R. Russell, Mater. Sci. Eng. 15 (1974) 253.
D. P. Williams and A. G. Evans, J. Test. Eval. 1 (1973) 264.
A. G. Evans, J. Mater. Sci. 7 (1972) 1137.
M. Matsui, T. Soma and I. Oda, in “Fracture Mechanics of Ceramics”, Vol. 4, edited by D. Bradt, P. H. Hasselman and F. F. Lange (Plenum Press, New York, 1978) p. 711.
J. G. Bruce, W. W. Gerberich and B. G. Koepke,, p. 687.
C. G. Annis and J. S. Cargill,, p. 737.
T. Fett, K. Keller and D. Munz, Int. J. Fract. 36 (1988) 3.
R. J. Young and P. W. R. Beaumont, J. Mater. Sci. 10 (1975) 1343.
P. S. Leevers, 17 (1982) 2469.
W.J. Cantwell, A. C. Roulin-Moloney and H. H. Kausch, J. Mater. Sci. Lett. 7 (1988) 976.
R. J. Young and P. W. R. Beaumont, J. Mater. Sci. 12 (1977) 684.
B. Stalder and H. H. Kausch, 17 (1982) 2481.
G. P. Marshall, L. H. Coutts and J. G. Williams, 9 (1974) 1409.
R. Frassine, T. Riccò, M. Rink and A. Pavan, 23 (1988) 4027.
P. W. R. Beaumont and R. J. Young, 10 (1975) 1334.
B. J. Pletka, E. R. Fuller and B. G. Koepke, in “Fracture Mechanics Applied to Brittle Materials”, ASTM STP 678, edited by S. W. Freiman (American Society for Testing and Materials, Philadelphia, PA, 1979) p. 19.
P. J. Hine, R. A. Duckett and I. M. Ward, J. Mater. Sci. 19 (1984) 3796.
P. S. Leevers and J. G. Williams, 22 (1987) 1097.
B. J. Pletka and S. M. Wiederhorn, in “Fracture Mechanics of Ceramics” edited by R. G. Bradt, D. P. H. Hasselman and F. F. Lange (Plenum Press, New York, 1977) p. 745.
F. E. Bailey and R. Walter, Polym. Eng. Sci. 15 (1975) 842.
Y. Chaoting, N. H. Ladizesky and I. M. Ward, J. Macromol. Sci. Phys. B27 (1988) 41.
P. S. Leevers, J. Mater. Sci. Lett. 5 (1986) 191.
S. R. Anthony, J. P. Chubb and J. Congleton, Philos. Mag. 22 (1970) 1201.
A. M. Serrano, G. E. Welsch and R. Gibala, Polym. Eng. Sci. 22 (1982) 934.
G. G. Trantina, J. Am. Ceram. Soc. 60 (1977) 388.
S. Hashemi and J. G. Williams, Polym. Eng. Sci. 26 (1986) 760.
J. G. Williams, “Fracture Mechanics of Polymers” (Ellis Horwood, Chichester, 1984).
ASTM E813-81, “Standard Test Method for JIc, A Measure of Fracture Toughness” (American Society for Testing and Materials, Philadelphia, PA).
ASTM E399-83, “Standard Test Method for Plane Strain Fracture Toughness of Metallic Materials”, (American Society for Testing and Materials, Philadelphia, PA).
J. E. Srawley, M. H. Jones and W. F. Brown, Mater. Res. Stand. 7 (1967) 262.
M. K. V. Chan and J. G. Williams, Polym. Eng. Sci. 21 (1981) 1019.
T. Riccò, R. Frassine and A. Pavan, J. Mater. Sci. 25 (1990) 1517.
Author information
Authors and Affiliations
Rights and permissions
About this article
Cite this article
Egan, B.J., Delatycki, O. Double torsion fracture testing of high-density polyethylene. JOURNAL OF MATERIALS SCIENCE 29, 6026–6032 (1994). https://doi.org/10.1007/BF00366889
Received:
Accepted:
Published:
Issue Date:
DOI: https://doi.org/10.1007/BF00366889