Skip to main content
SpringerLink
Log in

Study of the porosity produced in an aluminum alloy matrix composite due to a T6 heat treatment

  • Published:
Metallurgical and Materials Transactions A Aims and scope Submit manuscript

Abstract

In the present article, the reactions and phase transformations occurring between the fibers and the matrix during the T6 thermal treatment of an industrial composite are analyzed. The composite (taken from prototype diesel piston heads) consisted of an aluminum alloy conforming to AFNOR AS12UNG (Al-12 pct Si-1 pct Mg-1 pct Cu-1 pct Ni) that was reinforced with SAFFIL δ-alumina short fibers. Different heat-treating temperatures, holding times, and heating rates were considered. As a result of all these treatments, small to medium size (between 1 to 10 µm) holes were observed at the matrixfiber interfaces, although the amount and size varied depending on the heat-treating conditions. This porosity was attributed to the volume contraction associated with the reaction between the silica contained in the preform (colloidal silica is the binder for the alumina fibres) and the magnesium present in the aluminum alloy to produce MgO and Si during the solution heating treatment. This local volume contraction is higher than 28 pct.

This is a preview of subscription content, log in via an institution to check access.

Access this article

Log in via an institution

Price excludes VAT (USA)
Tax calculation will be finalised during checkout.

Instant access to the full article PDF.

Institutional subscriptions

Similar content being viewed by others

References

  1. S. Rawal: JOM, vol. 53(4), p. 14.

  2. Y.C. Chen and Y.C. Fann: MRL Bull. Res. Dev., 1992, vol. 6 (1), pp. 97–101.

    CAS  Google Scholar 

  3. J. Bär, H.-J. Gudladt, J. Illy, and J. Lendvai: Mater. Sci. Eng., 1998, vol. A248, pp. 181–86.

    Google Scholar 

  4. C.M. Friend, I. Horsffall, S.D. Luxton, and R.I. Young: in Cast Reinforced Metal Composites, S.G. Fishman and A.K. Dhingra, eds., ASM INTERNATIONAL, Metals Park, OH, 1988, pp. 309–15.

    Google Scholar 

  5. A.D. Mc Leod and C.M. Gabryel: Metall. Trans. A, 1992, vol. 23A, pp. 1279–83.

    CAS  Google Scholar 

  6. J.C. Lee, G.H. Kim, and H.I. Lee: Mater. Sci. Technol., 1997, vol. 13, pp. 182–86.

    CAS  Google Scholar 

  7. T. Christman and S. Suresh: Mater. Sci. Eng., 1988 vol. A102, pp. 211–16.

    Google Scholar 

  8. P. Appendino, C. Badini, F. Marino, and A. Tomas: Mater. Sci. Eng., 1991, vol. A35, pp. 275–77.

    Google Scholar 

  9. B. Dutta and M.K. Surappa: Scripta Metall. Mater., 1995, vol. 32, pp. 731–33.

    Article  CAS  Google Scholar 

  10. A. García-Romero: Doctoral Thesis, Universitat Politécnica de Catalunya, 1996, (in Spanish).

  11. Barcelona, CRC Handbook of Chemistry and Physics, 61st ed., R.C. Weast, ed., CRC Press Inc., Boca Raton, FL, 1980.

    Google Scholar 

  12. Phase Diagrams of Binary Magnesium Alloys, A.A. Nayeb-Hashemi and J.B. Clark, eds., ASM INTERNATIONAL, Metals Park, OH, 1988.

    Google Scholar 

  13. Handbook of Properties of Technical and Engineering Ceramics, Part I. An Introduction for the Engineer and Designer, R. Morrell, ed., The Stationery Office Books, London, 1985.

    Google Scholar 

  14. A. García-Romero, A.M. Irisarri, and M. Anglada: 9th Int. Conf. on the Mechanical Behaviour of Materials ICM9, Geneva, May 2003.

Download references

Author information

Authors and Affiliations

  1. the Fundacion Inasmet, 20009, San Sebastian, Spain

    A. García-Romero Doctor & A. M. Irisarri Doctor

  2. the Department Ciencia dels Materials I Enginyeria Metallurgica Etseib, UPC, Spain

    M. Anglada (Professor)

  3. Alcoa Avda Elche, 109, Alicante, Spain

    C. García-Cordovilla

Authors
  1. A. García-Romero Doctor
    View author publications

    You can also search for this author in PubMed Google Scholar

  2. A. M. Irisarri Doctor
    View author publications

    You can also search for this author in PubMed Google Scholar

  3. M. Anglada
    View author publications

    You can also search for this author in PubMed Google Scholar

  4. C. García-Cordovilla
    View author publications

    You can also search for this author in PubMed Google Scholar

Rights and permissions

Reprints and permissions

About this article

Cite this article

García-Romero, A., Irisarri, A.M., Anglada, M. et al. Study of the porosity produced in an aluminum alloy matrix composite due to a T6 heat treatment. Metall Mater Trans A 35, 2503–2510 (2004). https://doi.org/10.1007/s11661-006-0230-8

Download citation

  • Received:

  • Issue Date:

  • DOI: https://doi.org/10.1007/s11661-006-0230-8

Keywords

Search

Navigation