ALBERT

Description: TRACER (Tracing and Control of Engineering Requirements) is a database/word processing system created to document and maintain the order of both requirements and descriptive material associated with an engineering project. A set of hierarchical documents are normally generated for a project whereby the requirements of the higher level documents levy requirements on the same level or lower level documents. Traditionally, the requirements are handled almost entirely by manual paper methods. The problem with a typical paper system, however, is that requirements written and changed continuously in different areas lead to misunderstandings and noncompliance. The purpose of TRACER is to automate the capture, tracing, reviewing, and managing of requirements for an engineering project. The engineering project still requires communications, negotiations, interactions, and iterations among people and organizations, but TRACER promotes succinct and precise identification and treatment of real requirements separate from the descriptive prose in a document. TRACER permits the documentation of an engineering project's requirements and progress in a logical, controllable, traceable manner. TRACER's attributes include the presentation of current requirements and status from any linked computer terminal and the ability to differentiate headers and descriptive material from the requirements. Related requirements can be linked and traced. The program also enables portions of documents to be printed, individual approval and release of requirements, and the tracing of requirements down into the equipment specification. Requirement "links" can be made "pending" and invisible to others until the pending link is made "binding". Individuals affected by linked requirements can be notified of significant changes with acknowledgement of the changes required. An unlimited number of documents can be created for a project and an ASCII import feature permits existing documents to be incorporated. TRACER can automatically renumber section headers when inserting or deleting sections of a document and generate sign-off forms for any approval process as well as a table of contents. TRACER was implemented on an IBM PC under PC-DOS. The program requires 640K RAM, a hard disk, and PC-DOS version 3.3 or higher. It was written in CLIPPER (Summer '87). TRACER is available on two 5.25 inch 1.2Mb MS-DOS format diskettes. The executable program is also provided with the distribution. TRACER is a copyrighted work with all copyright vested in the National Aeronautics and Space Administration. IBM PC and PC-DOS are registered trademarks of International Business Machines. CLIPPER is a trademark of Nantucket Corporation.

Description: This paper describes the development as well as the on-ground and the in-flight evaluation of a low cost Global Positioning System (GPS) system for real-time tracking of sounding rockets. The flight unit comprises a modified ORION GPS receiver and a newly designed switchable antenna system composed of a helical antenna in the rocket tip and a dual-blade antenna combination attached to the body of the service module. Aside from the flight hardware a PC based terminal program has been developed to monitor the GPS data and graphically displays the rocket's path during the flight. In addition an Instantaneous Impact Point (IIP) prediction is performed based on the received position and velocity information. In preparation for ESA's Maxus-4 mission, a sounding rocket test flight was carried out at Esrange, Kiruna, on 19 Feb. 2001 to validate existing ground facilities and range safety installations. Due to the absence of a dedicated scientific payload, the flight offered the opportunity to test multiple GPS receivers and assess their performance for the tracking of sounding rockets. In addition to the ORION receiver, an Ashtech G12 HDMA receiver and a BAE (Canadian Marconi) Allstar receiver, both connected to a wrap-around antenna, have been flown on the same rocket as part of an independent experiment provided by the Goddard Space Flight Center. This allows an in-depth verification and trade-off of different receiver and antenna concepts.

Description: Some major steps are summarized in the evolution of autonomous design features for planetary exploration spacecraft. The control and data architectures for the Viking, Voyager, and Galileo spacecraft are considered. Telemetry and command capabilities are fundamental features of spacecraft design that have been successfully used for autonomous control. Also discussed is the Autonomous Redundancy and Maintenance Management Subsystem (ARMMS) concept. The software approach to autonomous control provides for modifications to the control process or the addition of new operating features during flight operations.

Description: Smaller and lower cost options of NASA's Solar Probe mission have recently been studied. The difference between these options and the results of earlier studies is dramatic. The motivation for low cost has encouraged the JPL design team to accomodate a smaller scientific payload using innovative multi-functional subsystems.

Description: In the decades since the advent of in situ plasma measurements on board spacecraft, the instrumentation has grown bigger, heavier, and more complex as our understanding of space plasmas improves and our appetite for more information increases...There has thus been a recent interest in the miniaturization of both spacecraft and the instrument payload... This paper describes the results and status of an ongoing design study to understand the problems and trade space of fully integrating an instrument into a micro-spacecraft.

Description: This report describes an investigation of the tensile, flexural, and impact properties of 10 selected types of phenolic molding materials. The materials were studied to see in what ways and to what extent their properties satisfy some assumptions on which the theory of strength of materials is based: namely, (a) isotropy, (b) linear stress-strain relationship for small strains, and (c) homogeneity. The effect of changing the dimensions of tensile and flexural specimens and the span-depth ratio in flexural tests were studied. The strengths of molded boxes and flexural specimens cut from the boxes were compared with results of tests on standard test specimens molded from the respective materials. The nonuniformity of a material, which is indicated by the coefficient of variation, affects the results of tests made with specimens of different sizes and tests with different methods of loading. The strength values were found to depend on the relationship between size and shape of the molded specimen and size and shape of the fillers. The most significant variations observed within a diversified group of materials were found to depend on the orientation of fibrous fillers. Of secondary importance was the dependence of the variability of test results on the pieces of filler incorporated into the molding powder as well as on the size of the piece. Static breaking strength tests on boxes molded from six representative phenolic materials correlated well with falling-ball impact tests on specimens cut from molded flat sheets. Good correlation was obtained with Izod impact tests on standard test specimens prepared from the molding materials. The static breaking strengths of the boxes do not correlate with the results of tensile or flexural tests on standard specimens.