ISSN:
0003-3146
Keywords:
Chemistry
;
Polymer and Materials Science
Source:
Wiley InterScience Backfile Collection 1832-2000
Topics:
Chemistry and Pharmacology
,
Physics
Description / Table of Contents:
An investigation was performed with the aim of ascertaining how a digested sewage sludge could be converted into mechanically stable flocs through the addition of a flocculating agent, while achieving the best possible dewatering efficiency with the lowest possible dosage of flocculation agent. In order to obtain conclusive results which can be transferred to large-scale plants, the effectiveness of the flocculating agents and the various flocculation procedures were tested in a patented, mobile, computer-assisted flocculation and dewatering apparatus.The sewage sludge was conditioned with flocculating agents which had previously been thoroughly characterized in terms of their chemical structure, charge density and molar mass. The cationic flocculating agents had charge densities ranging from 25-55 mol-% and molar masses from 1.5 · 106-12.9 · 106 g mol-, whereas the anionic flocculating agent had a charge density of 36 mol-% and a molar mass of 7.6 · lo6 g mol-. In contrast to other suspensions already investigated, for sewage sludge it was found that no improvement can be achieved in the already very high dewatering level when cationic monoflocculation is used (laboratory trial: 95% filtrate yield by mass after 4 s). Nor was it possible to reduce the optimum dosage by using the dual procedure. In addition, it was possible to show that the chemical structure, i.e. the nature of the polyelectrolyte, and the molar mass of the cationic polyelectrolytes investigated exert a by far larger influence on the dewatering efficiency than the charge density in a range between 25 and 55 mol-%. Furthermore, it has also been observed that the conditioning efficiency of the polyelectrolytes increases as the molar mass rises and the chemical structure influences the dewatering result primarily through the position of the charge-bearing group.
Notes:
Es wurde untersucht, wie ein ausgefaulter Klärschlamm durch eine optimale Flockungshilfsmittelzugabe zu mechanisch stabilen Flocken umgesetzt werden kann, so daß bei möglichst geringem Eintrag eine bestmögliche Entwässerung erzielt wird. Um dazu aussagekräftige, auf großtechnische Anlagen übertragbare Ergebnisse zu erhalten, wurde die Effektivität der Flockungshilfsmittel und der unterschiedlichen Flockungsverfahren in einer patentierten, mobilen, rechnergestützten Flockungs- und Entwässerungsapparatur getestet.Der Klärschlamm wurde im Mono- und Dualverfahren mit bezüglich ihrer chemischen Struktur, Molmasse und Ladungsdichte (LD) eingehend charakterisierten kationischen (LD: 25-55 mol-%; Mw: 1,5 · 106- 12,9 · 106 g mol-1) und einem anionischen (LD: 36 mol-%; Mw: 7,6 · 106 g mol-1) Flockungshilfsmittel konditioniert. Im Gegensatz zu anderen bereits untersuchten Trüben konnte beim Klärschlamm weder eine Verbesserung der ohnehin sehr guten Entwässerbarkeit mittels kationischer Monoflockung (Laborversuch: 95 Gew.-% Filtratausbeute nach 4 s), noch eine Verringerung der optimalen Einsatzmengen durch die Anwendung des Dualverfahrens erzielt werden. Darüber hinaus konnte gezeigt werden, daß die chemische Struktur und die Molmasse der untersuchten kationischen Polyelektrolyte einen weit größeren Einfluß auf die Entwässerungseffektivität besitzen als die Ladungsdichte in einem Bereich zwischen 25 und 55 mol-%. Ferner erwies sich, daß die Konditionierungseffektivität der Polyelektrolyte mit steigender Molmasse zunimmt und die chemische Struktur hauptsächlich durch die Position der ladungstragenden Gruppe einen Einfluß auf das Entwässerungsergebnis zeigt.
Additional Material:
5 Ill.
Type of Medium:
Electronic Resource
URL:
http://dx.doi.org/10.1002/apmc.1997.052500102
Permalink