ALBERT

All Library Books, journals and Electronic Records Telegrafenberg

feed icon rss

Ihre E-Mail wurde erfolgreich gesendet. Bitte prüfen Sie Ihren Maileingang.

Leider ist ein Fehler beim E-Mail-Versand aufgetreten. Bitte versuchen Sie es erneut.

Vorgang fortführen?

Exportieren
Filter
  • Polymer and Materials Science  (25)
  • AIRCRAFT  (6)
  • Meteorology and Climatology
  • 1970-1974  (31)
  • 1
    Digitale Medien
    Digitale Medien
    New York : Wiley-Blackwell
    Journal of Polymer Science Part A-2: Polymer Physics 8 (1970), S. 277-287 
    ISSN: 0449-2978
    Schlagwort(e): Physics ; Polymer and Materials Science
    Quelle: Wiley InterScience Backfile Collection 1832-2000
    Thema: Chemie und Pharmazie , Physik
    Notizen: Studies have been made on the dynamic and steady-shear melt rheology of an ethylene-methacrylic acid copolymer and two of its salts obtained by partial neutralization with sodium and with calcium bases. Measurements were made with a Weissenberg rheogoniometer over a broad range of shear rates and frequency in the temperature interval mainly from 100 to 160°C. The temperature coefficients of dynamic and steady shear viscosity are evaluated at both constant shear rate and constant stress. Likewise, complex dynamic viscosities and apparent high steady-flow viscosities and intercompared at equivalent frequencies and shear rates. The un-ionized acid copolymer shows good correlation between the frequency dependence of the complex viscosity and the shear rate dependence of the apparent viscosity. This is not true for either the sodium salt or the calcium salt. These results are consistent with the two-phase structural model for these materials, i.e., a matrix of hydrocarbon in which are embedded ionic domains.
    Zusätzliches Material: 12 Ill.
    Materialart: Digitale Medien
    Standort Signatur Erwartet Verfügbarkeit
    BibTip Andere fanden auch interessant ...
  • 2
    Digitale Medien
    Digitale Medien
    New York, NY [u.a.] : Wiley-Blackwell
    Journal of Applied Polymer Science 18 (1974), S. 1805-1819 
    ISSN: 0021-8995
    Schlagwort(e): Chemistry ; Polymer and Materials Science
    Quelle: Wiley InterScience Backfile Collection 1832-2000
    Thema: Chemie und Pharmazie , Maschinenbau , Physik
    Notizen: Isoprene was polymerized in batch reactors by use of bottle polymerization techniques at 30°, 40°, and 50°C at concentrations from 1 to 5 molar. Butyllithium concentration was varied from 0.005 to 0.03 molar. Isoprene and n-butyllithium conversions and molecular weight distributions were determined for different reaction times. Rate equations for the initiation and propagation reactions are presented. The importance of the association reactions in obtaining a narrow molecular weight distribution is illustrated.
    Zusätzliches Material: 8 Ill.
    Materialart: Digitale Medien
    Standort Signatur Erwartet Verfügbarkeit
    BibTip Andere fanden auch interessant ...
  • 3
    Digitale Medien
    Digitale Medien
    New York : Wiley-Blackwell
    Die Makromolekulare Chemie 162 (1972), S. 19-30 
    ISSN: 0025-116X
    Schlagwort(e): Chemistry ; Polymer and Materials Science
    Quelle: Wiley InterScience Backfile Collection 1832-2000
    Thema: Chemie und Pharmazie , Physik
    Beschreibung / Inhaltsverzeichnis: Es wurde gezeigt, daß sich in Hochdruck-Polyäthylen in der Nähe der Schmelztemperatur und unter bestimmten Bedingungen in bezug auf Orientierung und Druck, wie sie im Instron-Extrusions-Kapillar-Rheometer vorliegen, ungewöhnliche morphologische Strukturen ausbilden. Die bemerkenswert hohe optische Transparenz und die Spannungsmoduln der in diesen Fäden vorliegenden morphologischen Gebilde waren Gegenstände der Untersuchungen. Einzelheiten des Kristallisationsverfahrens werden beschrieben. Die morphologischen Strukturen, die sich bei dem „Instron-Verfahren“ herausbilden, wurden mit Hilfe von röntgenographischen, kalorimetrischen, mikroskopischen und mechanischen Messungen untersucht. Die transparenten Fasern setzen sich aus einer großen Zahl von Mikrofibrillen, die einen hohen kristallinen Orientierungsgrad parallel zur Kapillarachse bestizen, zusammen. Elektronenbeugung und kalorimetrische Untersuchungen zeigen, daß ein Teil der Fasern einen ungewöhnlich hohen Ordnungsgrad besitzt. Es werden Strukturmodelle für die Fasern vorgeschlagen.
    Notizen: Unusual morphologies have been shown to be produced in high density polyethylene near its melting point and under selective conditions of orientation and pressure existing in an Instron capillary extrusion rheometer. Points of study involve the remarkably high optical clarity and tensile moduli for the morphologies produced in these filaments. Details of the crystallization procedure are provided. The morphologies resulting from the Instron procedure have been analyzed by several different techniques. X-ray, calorimetry, microscopy and modulus data are discussed. The transparent filaments are composed of a large number of microfibers having a high degree of crystalline orientation parallel to the capillary axis. Electron diffraction and calorimetric studies indicate that a portion of the strands have an unusually high degree of order. Structural models for the strands are also proposed.
    Zusätzliches Material: 6 Ill.
    Materialart: Digitale Medien
    Standort Signatur Erwartet Verfügbarkeit
    BibTip Andere fanden auch interessant ...
  • 4
    Digitale Medien
    Digitale Medien
    New York : Wiley-Blackwell
    Journal of Polymer Science Part A-2: Polymer Physics 10 (1972), S. 647-656 
    ISSN: 0449-2978
    Schlagwort(e): Physics ; Polymer and Materials Science
    Quelle: Wiley InterScience Backfile Collection 1832-2000
    Thema: Chemie und Pharmazie , Physik
    Notizen: In order to investigate the role of solid morphology on molecular relaxation in crystaline polymers, the effect of melting on the α relaxation in poly(hexamethylene sebacamide) (nylon 610) was measured dielectrically. It was found that the α loss peak was continuous into the melt with respect to location in the frequency-temperature domain and with respect to the shape of the peak. However, the strength of the process, as measured by the difference in the relaxed and unrelaxed dielectric constants, was discontinuous on melting, the process being much stronger in the melt. These observations are consistent with a two-phase model of discrete crystalline and amorphous regions. The relaxation takes place in the amorphous regions, and melting creates more of this material but does not greatly after its nature. The correlation of the amount of amorphous material as measured by dielectric relaxation with that infrared from density measurements is discussed for nylon610, polyoxymethylene, and poly(ethylene oxide).
    Zusätzliches Material: 10 Ill.
    Materialart: Digitale Medien
    Standort Signatur Erwartet Verfügbarkeit
    BibTip Andere fanden auch interessant ...
  • 5
    Digitale Medien
    Digitale Medien
    New York : Wiley-Blackwell
    Journal of Polymer Science Part A-2: Polymer Physics 10 (1972), S. 877-886 
    ISSN: 0449-2978
    Schlagwort(e): Physics ; Polymer and Materials Science
    Quelle: Wiley InterScience Backfile Collection 1832-2000
    Thema: Chemie und Pharmazie , Physik
    Notizen: Several important aspects of the flow in polymer melts through capillaries remain unexplored. This paper examines experimentally one such effect associated with the radial shear-stress gradient in capillaries. During capillary melt flow of a polymer with a wide molecular weight distribution, migration of the large molecules away from the region of highest shear stress, i.e., at the capillary wall, has been predicted but only modestly investigated. This effect has the potential to produce a molecular weight spectrum over the cross section of extruded polymer. Studies of distribution in shear were conducted on a well-characterized wide-distribution polystyrene (M̄w = 234,000). An Instron Rheometer equipped with a long capillary (length/diameter ratio of 66.7) was used to perform the extrusion at temperatures of 160-250°C. A solvent coring procedure was used to dissolve away concentric layers of polymer from the extrudate for molecular weight analyses. The method has been shown to cut clean sections without selective extraction. Values of M̄w, M̄n and M̄w/M̄n were calculated from complete molecular weight distribution data obtained by calibrated gel permeation chromatography. For a wide range of shear rates and temperatures, no evidence for molecular fractionation was observed. Shear degradation of this polymer was found to be small. However, at high shear rates at 250°C, evidence indicating extensive shear-induced thermal degradation was found. No evidence for oxidative degradation at the extrudate surface was found at either low or high shear rates at this temperature.
    Zusätzliches Material: 2 Ill.
    Materialart: Digitale Medien
    Standort Signatur Erwartet Verfügbarkeit
    BibTip Andere fanden auch interessant ...
  • 6
    Digitale Medien
    Digitale Medien
    New York : Wiley-Blackwell
    Journal of Polymer Science Part A-2: Polymer Physics 9 (1971), S. 2255-2258 
    ISSN: 0449-2978
    Schlagwort(e): Physics ; Polymer and Materials Science
    Quelle: Wiley InterScience Backfile Collection 1832-2000
    Thema: Chemie und Pharmazie , Physik
    Zusätzliches Material: 2 Ill.
    Materialart: Digitale Medien
    Standort Signatur Erwartet Verfügbarkeit
    BibTip Andere fanden auch interessant ...
  • 7
    Digitale Medien
    Digitale Medien
    New York : Wiley-Blackwell
    Journal of Polymer Science Part A-2: Polymer Physics 9 (1971), S. 463-482 
    ISSN: 0449-2978
    Schlagwort(e): Physics ; Polymer and Materials Science
    Quelle: Wiley InterScience Backfile Collection 1832-2000
    Thema: Chemie und Pharmazie , Physik
    Notizen: Several corrections possibly required for capillary flow are based on the existence of a linear relationship between the pressure drop along the capillary and the length-to-diameter ratio at a given temperature and shear rate. Recently, the appearance of nonlinearities in this relationship has created some concern as to the cause of this behavior. The occurrence and an explanation of the nonlinearities for polystyrene form the basis of this study. A narrow-distribution, low molecular weight (20,400) polystyrene was tested in eight capillaries at temperatures of 140 and 160°C to initiate the discussion of the nonlinearity in a ΔP (pressure) versus L/D (length/diameter of capillary) plot. The sample exhibits negligible extrudate swelling at all pressures which reinforces the idea that pressure is influencing the flow. The pressure dependence of viscosity is determined using the equivalent expression of the WLF equation derived from free volume theory. Justification for its use is presented. A pressure correction, representing the increased shear stress necessary for flow of the higher viscosity material, is found to linearize the ΔP versus L/D data. A narrow-distribution, high molecular weight polystyrene (670,000) is subjected to a similar analysis at 165°C by using nine capillaries. The situation is quite different, as the high molecular weight sample is not nearly as ideal as the low molecular weight polystyrene.
    Zusätzliches Material: 14 Ill.
    Materialart: Digitale Medien
    Standort Signatur Erwartet Verfügbarkeit
    BibTip Andere fanden auch interessant ...
  • 8
    Digitale Medien
    Digitale Medien
    New York : Wiley-Blackwell
    Journal of Polymer Science Part A-2: Polymer Physics 10 (1972), S. 1135-1143 
    ISSN: 0449-2978
    Schlagwort(e): Physics ; Polymer and Materials Science
    Quelle: Wiley InterScience Backfile Collection 1832-2000
    Thema: Chemie und Pharmazie , Physik
    Notizen: The Melting of various polyethylene structures is compared by using data obtained on the Perkin-Elmer differential scanning calorimeter (DSC). Transparent, high-density samples crystallized under both orientation and pressure in the Instron capillary rheometer are compared with samples crystallized from dilute solution by stirring and with samples crystallized under high pressure. The latter two structures are assumed to contain extended-chain crystallites. By comparison, the melting points and the superheatability of the Instron samples are consistent with the presence of an extended-chain crystal component. The melting of irradiated samples crystallized in the rheometer is also observed to be consistent with this conclusion. In addition, DSC data are compared with the melting points defined with a polarized light microscope equipped with a hot stage.
    Zusätzliches Material: 5 Ill.
    Materialart: Digitale Medien
    Standort Signatur Erwartet Verfügbarkeit
    BibTip Andere fanden auch interessant ...
  • 9
    Digitale Medien
    Digitale Medien
    New York : Wiley-Blackwell
    Journal of Polymer Science Part A-2: Polymer Physics 10 (1972), S. 1639-1655 
    ISSN: 0449-2978
    Schlagwort(e): Physics ; Polymer and Materials Science
    Quelle: Wiley InterScience Backfile Collection 1832-2000
    Thema: Chemie und Pharmazie , Physik
    Notizen: The viscoelastic (VE) response of freeze-dried blends of polystyrene (PS) and poly-(2,6-dimethyl phenylene oxide) (PPO) has been studied as a function of composition, frequency, and temperature to examine the degree of rheological compatibility. When blended together, the relaxation processes of both molecular species exhibit the same temperature dependence. However, the temperature dependence of the VE response is a function of composition. It is shown that this behavior can be predicted from the measured glass transition temperatures by assuming the additivity of the free volumes of the components. The properties of the blends are compared at equal free volumes. The effective segmental friction factor is found to be independent of composition while the modulus of the rubbery plateau increases with PPO concentration. This result is interpreted as a change in the entanglement molecular weight Me of the blends. When the changes in Me are considered, the relationship between the zero-shear viscosity η0 and the 3.4 power of the weight-average molecular weight, commonly found for high molecular weight homopolymers, predicts the compositional dependence of η0 for the PPO-PS blends. It is concluded that the PPO-PS system forms a rheologically compatible blend.
    Zusätzliches Material: 10 Ill.
    Materialart: Digitale Medien
    Standort Signatur Erwartet Verfügbarkeit
    BibTip Andere fanden auch interessant ...
  • 10
    Digitale Medien
    Digitale Medien
    New York : Wiley-Blackwell
    Journal of Polymer Science Part A-2: Polymer Physics 9 (1971), S. 731-745 
    ISSN: 0449-2978
    Schlagwort(e): Physics ; Polymer and Materials Science
    Quelle: Wiley InterScience Backfile Collection 1832-2000
    Thema: Chemie und Pharmazie , Physik
    Notizen: General expressions for determining the pressure coefficient and axial distribution of the viscosity and pressure in capillary flow are derived for Newtonian and shear-thinning fluids. The pressure-dependent viscosity model is obtained from the WLF equation as derived from Doolittle's free volume theory. The model has also been derived from Eyring's hole theory for viscosity. Poiseuille's equation is modified to correct for the pressure effect on viscosity. A Newtonian, low-molecular-weight polystyrene and a shear-thinning, high-molecular-weight polystyrene were tested in an Instron capillary rheometer. The axial velocity distribution was found to be negligibly affected by pressure whereas the viscosity was shown to increase markedly with a decrease in volume. The resulting pressure effects on the viscosity of both samples were analyzed by using the derived expressions.
    Zusätzliches Material: 8 Ill.
    Materialart: Digitale Medien
    Standort Signatur Erwartet Verfügbarkeit
    BibTip Andere fanden auch interessant ...
Schließen ⊗
Diese Webseite nutzt Cookies und das Analyse-Tool Matomo. Weitere Informationen finden Sie hier...