ALBERT

Description: Computations were made for those test cases of Problem 3 which were designated as laminar flows, viz., test cases 3.1, 3.2, 3.4, and 3.5. These test cases corresponded to flows over a flat plate and a compression ramp at high Mach number and at high Reynolds number. The computations over the compression ramps indicate a substantial streamwise extent of separation. Based on previous experience with separated laminar flows at high Mach numbers which indicated a substantial effect with spatial grid refinement, a series of computations with different grid sizes were performed. Also, for the flat plate, comparisons of the results for two different algorithms were made.

Description: A development status evaluation is presented for CFD methods applicable to fuselage-integrated scramjet powerplant incorporating hypersonic vehicles; these methods are critically important due to the unavailability of experimental facilities for such elevated Mach number/high-enthalphy conditions. Advancements are required in algorithm robustness and speed, geometric flexibility, and the inclusion of more complete flow physics. The most serious deficiencies lie in turbulence modeling, the lack of complete transition-prediction methods, and combustion modeling.

Description: The NASCRIN program was developed for analyzing two-dimensional flow fields in supersonic combustion ramjet (scramjet) inlets. NASCRIN solves the two-dimensional Euler or Navier-Stokes equations in conservative form by an unsplit, explicit, two-step finite-difference method. A more recent explicit-implicit, two-step scheme has also been incorporated in the code for viscous flow analysis. An algebraic, two-layer eddy-viscosity model is used for the turbulent flow calculations. NASCRIN can analyze both inviscid and viscous flows with no struts, one strut, or multiple struts embedded in the flow field. NASCRIN can be used in a quasi-three-dimensional sense for some scramjet inlets under certain simplifying assumptions. Although developed for supersonic internal flow, NASCRIN may be adapted to a variety of other flow problems. In particular, it should be readily adaptable to subsonic inflow with supersonic outflow, supersonic inflow with subsonic outflow, or fully subsonic flow. The NASCRIN program is available for batch execution on the CDC CYBER 203. The vectorized FORTRAN version was developed in 1983. NASCRIN has a central memory requirement of approximately 300K words for a grid size of about 3,000 points.

Description: Flow through a two-dimensional duct with supersonic inflow is numerically investigated, from the viewpoint of the formation of Mach reflection, aerodynamic choking, and the possibility of constructing a curve similar to that for the quasi-one-dimensional flow in a converging-diverging duct. Such a curve can be used to determine whether a duct with a certain area ratio will or will not choke for a given inflow Mach number. Plots of pressure and mass flux contours are obtained for a given duct configuration. It is found that the two-dimensional flow always chokes at a higher Mach number than the corresponding quasi-one-dimensional flow for a given throat/inlet flow area ratio.

Description: Low Reynolds number flow of an ideal gas over a blunt axisymmetric body of large half-angle at small angles of attack is investigated, for the case of laminar hypersonic flow. Time-varying viscous shock layer equations describing the flowfield are obtained from the full Navier-Stokes system by keeping terms to second order in the inverse square root of Re in both viscous and inviscid regions; the equations are valid for moderate to high Re. Drag, skin friction, and heating rates were obtained at small (or zero) angles of attack. Conditions experienced by planetary entry probes during the high-altitude (early) legs of an atmospheric entry trajectory are pertinent to the problem.

Description: A comparative study was made with four different codes for solving the compressible Navier-Stokes equations using three different test problems. The first of these cases was hypersonic flow through the P8 inlet, which represents inlet configurations typical of a hypersonic airbreathing vehicle. The free-stream Mach number in this case was 7.4. This 2-D inlet was designed to provide an internal compression ratio of 8. Initial calculations were made using two state-of-the-art finite-volume upwind codes, CFL3D and USA-PG2, as well as NASCRIN, a code which uses the unsplit finite-difference technique of MacCormack. All of these codes used the same algebraic eddy-viscosity turbulence model. In the experiment, the cowl lip was slightly blunted; however, for the computations, a sharp cowl leading edge was used to simplify the construction of the grid. The second test problem was the supersonic (Mach 3.0) flow in a three-dimensional corner formed by the intersection of two wedges with equal wedge angles of 9.48 degrees. The flow in such a corner is representative of the flow in the corners of a scramjet inlet. Calculations were made for both laminar and turbulent flow and compared with experimental data. The three-dimensional versions of the three codes used for the inlet study (CFL3D, USA-PG3, and SCRAMIN, respectively) were used for this case. For the laminar corner flow, a fourth code, LAURA, which also uses recently-developed upwind technology, was also utilized. The final test case is the two-dimensional hypersonic flow over a compression ramp. The flow is laminar with a free-stream Mach number of 14.1. In the experiment, the ramp angle was varied to change the strength of the ramp shock and the extent of the viscous-inviscid interaction. Calculations were made for the 24-degree ramp configuration which produces a large separated-flow region that extends upstream of the corner.