ALBERT

Description: Bone regeneration procedures require alternative graft biomaterials to those for autogenous bone. Therefore, we developed a novel porcine graft using particle sizes of 250–500 μm and 500–1000 μm in rabbit calvarial bone defects and compared the graft properties with those of commercial hydroxyapatite (HA)/beta-tricalcium phosphate (β-TCP) over eight weeks. Surgery was performed in 20 adult male New Zealand white rabbits. During a standardized surgical procedure, four calvarial critical-size defects of 5 mm diameter and 3 mm depth were prepared. The defects were filled with HA/β-TCP, 250–500 μm or 500–1000 μm porcine graft, and control defects were not filled. The animals were grouped for sacrifice at 1, 2, 4, and 8 weeks post-surgery. Subsequently, sample blocks were prepared for micro-computed tomography (micro-CT) scanning and histological sectioning. Similar bone formations were observed in all three treatment groups, although the 250–500 μm porcine graft performed slightly better. Rabbit calvarial bone tissue positively responded to porcine grafts and commercial HA/β-TCP, structural analyses showed similar crystallinity and porosity of the porcine and HA/β-TCP grafts, which facilitated bone formation through osteoconduction. These porcine grafts can be considered as graft substitutes, although further development is required for clinical applications.

Description: Recent advances in microelectronics and wireless transmission technology have led to the development of various implantable sensors for real-time monitoring of bladder conditions. Although various sensing approaches for monitoring bladder conditions were reported, most such sensors have remained at the laboratory stage due to the existence of vital drawbacks. In the present study, we explored a new concept for monitoring the bladder capacity on the basis of potentiometric principles. A prototype of a potentiometer module was designed and fabricated and integrated with a commercial wireless transmission module and power unit. A series of in vitro pig bladder experiments was conducted to determine the best design parameters for implementing the prototype potentiometric device and to prove its feasibility. We successfully implemented the potentiometric module in a pig bladder model in vitro, and the error of the accuracy of bladder volume detection was 〈±3%. Although the proposed potentiometric device was built using a commercial wireless module, the design principles and animal experience gathered from this research can serve as a basis for developing new implantable bladder sensors in the future.

Description: This paper presents the microfabrication of an acoustic impedance gradient matching layer on a spherically-shaped piezoelectric ultrasonic transducer. The acoustic matching layer can be designed to achieve higher acoustic energy transmission and operating bandwidth. Also included in this paper are a theoretical analysis of the device design and a micromachining technique to produce the novel transducer. Based on a design of a lead titanium zirconium (PZT) micropillar array, the constructed gradient acoustic matching layer has much better acoustic transmission efficiency within a 20–50 MHz operation range compared to a matching layer with a conventional quarter-wavelength thickness Parylene deposition. To construct the transducer, periodic microcavities are built on a flexible copper sheet, and then the sheet forms a designed curvature with a ball shaping. After PZT slurry deposition, the constructed PZT micropillar array is released onto a curved thin PZT layer. Following Parylene conformal coating on the processed PZT micropillars, the PZT micropillars and the surrounding Parylene comprise a matching layer with gradient acoustic impedance. By using the proposed technique, the fabricated transducer achieves a center frequency of 26 MHz and a −6 dB bandwidth of approximately 65%.

Description: Based on China’s inter-provincial panel data from 1999–2009, this paper has tested the impact and extent of marketization, government governance, and legal environment of sustainable economic development by controlling physical capital, human capital and productivity, so as to find the institutional reality for the difference in China’s economic development and another explanation for it. It turns out that marketization, government governance, and legal environment play significant roles in promoting sustainable economic development. Further tests show that the results of Eastern China are consistent with China’s inter-provincial results; while in Western China, the promotion effect of marketization, government governance, and legal environment on sustainable economic development is not significant.

Description: Past studies in humans have demonstrated horizontal and vertical bone loss after six months following tooth extraction. Many biomaterials have been developed to preserve bone volume after tooth extraction. Type I collagen serves as an excellent delivery system for growth factors and promotes angiogenesis. Calcium phosphate ceramics have also been investigated because their mineral chemistry resembles human bone. The aim of this study was to compare the performance of a novel bioresorbable purified fibrillar collagen and hydroxyapatite/β-tricalcium phosphate (HA/β-TCP) ceramic composite versus collagen alone and a bovine xenograft-collagen composite in beagles. Collagen plugs, bovine graft-collagen composite and HA/β-TCP-collagen composite were implanted into the left and right first, second and third mandibular premolars, and the fourth molar was left empty for natural healing. In total, 20 male beagle dogs were used, and quantitative and histological analyses of the extraction ridge was done. The smallest width reduction was 19.09% ± 8.81% with the HA/β-TCP-collagen composite at Week 8, accompanied by new bone formation at Weeks 4 and 8. The HA/β-TCP-collagen composite performed well, as a new osteoconductive and biomimetic composite biomaterial, for socket bone preservation after tooth extraction.

Description: This paper presents an innovative tuning fork-shaped ionic polymer metal composite (IPMC) actuator. With an integrated soft strain gauge and water supply mechanism (WSM), the surface strain of the actuator can be sensed in situ, and providing a continuous water supply maintains the water content inside the IPMC for long-term operation in air. The actuator was fabricated using a micromachining technique and plated with a nickel electrode. The device performance was experimentally characterized and compared with an actuator without a WSM. A large displacement of 1.5 mm was achieved for a 6 mm-long prong with 7-V dc actuation applied for 30 s. The measured current was analyzed using an electrochemical model. The results revealed that the faradaic current plays a crucial role during operation, particularly after 10 s. The measured strain confirms both the bending and axial strain generation during the open-and-close motion of the actuator prongs. Most of the water loss during device operation was due to evaporation rather than hydrolysis. The constructed WSM effectively maintained the water content inside the IPMC for long-term continuous operation.

Description: Using annual data from 1997–2014 of 30 provinces, municipalities, and autonomous regions, subdividing trended and cyclical volatility of macroeconomics and inflation, considering different indicators of financial development and financial structure, this paper investigated the impact of financial development and financial structure on macroeconomic volatility. The empirical results found that (1) the trended and cyclical volatility of the previous macroeconomic period had a significantly positive impact on that of the current period, and the impact of trended volatility was greater than that of cyclical volatility; (2) financial development had a significantly negative impact on macroeconomic cyclical volatility through inflation cyclical volatility, but inflation trended volatility would amplify macroeconomic volatility; financial markets have no significant effect on macroeconomic volatility; financial structure measured with the ratio of stock market turnover and the efficiency of the financial development had a significant positive impact on macroeconomic cyclical volatility; and (3) inflation trended volatility had a significantly negative impact on macroeconomic cyclical volatility and trended volatility, while inflation cyclical volatility had a significantly positive impact on macroeconomic cyclical volatility.

Description: Minerals, Vol. 7, Pages 162: Muscovite 40Ar/39Ar Age and H-O-S Isotopes of the Shimensi Tungsten Deposit (Northern Jiangxi Province, South China) and Their Metallogenic Implications Minerals doi: 10.3390/min7090162 Authors: Wen-Feng Wei Bing Yan Neng-Ping Shen Lei Liu Yong Zhang Xin-Kui Xiang The Shimensi deposit (Northern Jiangxi, South China) is a recently discovered super-large tungsten deposit. Muscovite 40Ar/39Ar dating yielded a plateau age of 145.7 ± 0.9 Ma, with normal and inverse isochronal ages being 145.4 ± 1.4 Ma and 145.3 ± 1.4 Ma, respectively. The muscovite 40Ar/39Ar age, which can represent the mineralization age, coincides well with the published zircon U–Pb ages (143–148 Ma) of the ore-hosting granites, which indicates that the tungsten mineralization was syn-magmatic. The new age reported here confirms that the Shimensi tungsten deposit is part of a large Early Cretaceous (147–136 Ma) tungsten-polymetallic belt in South China. Measured and calculated sulfur isotopic compositions (δ34Sminerals = −3.0‰ to 1.1‰, average −1.3‰; δ 34 S H 2 S = −4.5‰ to +1.2‰, average −1.8‰) of the Shimensi ore-forming fluids indicate that the sulfur was mainly magmatic-derived. The calculated and measured oxygen and hydrogen isotopic compositions ( δ 18 O H 2 O = 4.1‰ to 6.7‰, δD = −62.7‰ to −68‰) of the ore-forming fluids indicate a dominantly magmatic source with a meteoric water input. Oxygen isotopic modelling of the boiling/mixing processes indicates that the Shimensi tungsten mineralization was caused mainly by fluid mixing of magmatic hydrothermal fluid with meteoric water.

Description: Minerals, Vol. 7, Pages 195: The Influence of Backwater Al3+ on Diaspore Bauxite Flotation Minerals doi: 10.3390/min7100195 Authors: Chaojun Fang Ziyong Chang Qiming Feng Wei Xiao Shichao Yu Guanzhou Qiu Jun Wang The effect of Al3+ in backwater on the flotation of diaspore bauxite was investigated by micro-flotation tests and the underlying mechanisms were investigated by inductively coupled plasma (ICP) measurement, zeta potential measurements, solution chemistry analyses, and synchrotron near edge X-ray absorption fine structure (NEXAFS) analyses. The ICP measurement results show the concentration of Al3+ in backwater was up to 1 × 10−4 mol/L. The micro-flotation results indicated that backwater Al3+ reduced the flotation recovery of diaspore and improved the flotation recovery of kaolinite at pH 9, which was the pH value used in the industrial flotation. The adsorption of Al3+ species changed the zeta potential, the Al atomic abundance, and the number of active sites on the mineral surface. In particular, the result of solution chemistry analyses and synchrotron NEXAFS analyses show that the Al3+ in backwater was adsorbed on the mineral surface in the form of Al(OH)3 (s), and the bond of –Al–O–Al–(OH)2 or –Al/Si–O–Al–(OH)2 was formed at pH 9. It changed the intensity of hydrogen bond force between minerals and collectors, and resulted in the depression of diaspore flotation and the activation of kaolinite flotation. This study can be used to guide the application of backwater in the flotation of diaspore bauxite in industry.

Description: Energies, Vol. 10, Pages 1966: Optimal Capacity Configuration for Energy Hubs Considering Part-Load Characteristics of Generation Units Energies doi: 10.3390/en10121966 Authors: Shan Deng Qinghua Wu Zhaoxia Jing Lilan Wu Feng Wei Xiaoxin Zhou The simulation model is one of the key points affecting the optimal planning and operation of energy hubs (EHs). Since treating the efficiencies of generation units as constants would significantly simplify the calculation, only a simplified model is investigated in most research works. In this paper, aiming at optimizing the capacity configuration of an EH, we present a part-load characteristics-based (PLCB) model, in which the efficiencies of generation units will change with the fluctuating load. Based on the PLCB model, the accuracy of the EH model can be improved. Furthermore, a two-stage planning method is proposed to solve the optimal capacity configuration problem of the EH. Group Search Optimizer (GSO) is used to determine the optimal size in the first stage, and a mathematical programming method is applied to obtain the optimal operation of the EH in the second stage. Comparative studies using the PLCB model and the simplified model are performed to examine the impacts of equipment part-load characteristics on the sizing results. Simulation results indicate that the proposed model appears to have a better economic performance than the simplified model.