ALBERT

All Library Books, journals and Electronic Records Telegrafenberg

X
feed icon rss

Your email was sent successfully. Check your inbox.

An error occurred while sending the email. Please try again.

Proceed reservation?

Export
  • 1
    Electronic Resource
    Electronic Resource
    Powder diffraction using imaging plates at the Australian National Beamline Facility at the Photon Factory : Proceedings of the 5th international conference on synchrotron radiation instrumentation (1995)
    [S.l.] : American Institute of Physics (AIP)
    Review of Scientific Instruments 66 (1995), S. 1351-1353 
    Details
    ISSN: 1089-7623
    Source: AIP Digital Archive
    Topics: Physics , Electrical Engineering, Measurement and Control Technology
    Notes: A novel x-ray diffractometer was installed at the Australian National Beamline Facility at the Photon Factory, Japan, in October 1993. One of the major capabilities of the instrument is high speed high resolution powder diffraction using imaging plate detectors. The diffractometer combines a two circle goniometer and a large cassette in which imaging plates can be loaded covering 320° of 2θ. The diffractometer is enclosed in a large vacuum chamber and can be operated in air, vacuum, or helium. Recently, powder data has been obtained from rutile (TiO2) and NBS Si 640b at wavelengths from 0.62 to 1.9 A(ring) using imaging plates, and has been used to characterize the performance of the instrument. The data has been refined using the Rietveld method and R values of under 2% obtained. The resolution of the system varies from a minimum of about 0.04° to around 0.25° at 2θ angles around 160°, which is the equal of most synchrotron based powder diffractometers, and only slightly worse than that obtained using an analyzer crystal and scintillation detector. Using the imaging plates, 160° of data is simultaneously acquired in an exposure of about 10 min, compared to conventional counter diffractometer scans which routinely exceed 10 hours. © 1995 American Institute of Physics.
    Type of Medium: Electronic Resource
    URL: http://dx.doi.org/10.1063/1.1145972
    Location Call Number Expected Availability
    BibTip Others were also interested in ...
    Paper (German National Licenses)
    Fulltext
  • 2
    facet.materialart.
    Unknown
    Materials, Vol. 11, Pages 666: Effect of Inoculant Alloy Selection and Particle Size on Efficiency of Isomorphic Inoculation of Ti-Al (2018)
    MDPI Publishing
    In: Materials
    Details
    Publication Date: 2018-04-26
    Description: Materials, Vol. 11, Pages 666: Effect of Inoculant Alloy Selection and Particle Size on Efficiency of Isomorphic Inoculation of Ti-Al Materials doi: 10.3390/ma11050666 Authors: J. R. Kennedy B. Rouat D. Daloz E. Bouzy J. Zollinger The process of isomorphic inoculation relies on precise selection of inoculant alloys for a given system. Three alloys, Ti-10Al-25Nb, Ti-25Al-10Ta, and Ti-47Ta (at %) were selected as potential isomorphic inoculants for a Ti-46Al alloy. The binary Ti-Ta alloy selected was found to be ineffective as an inoculant due to its large density difference with the melt, causing the particles to settle. Both ternary alloys were successfully implemented as isomorphic inoculants that decreased the equiaxed grain size and increased the equiaxed fraction in their ingots. The degree of grain refinement obtained was found to be dependent on the number of particles introduced to the melt. Also, more new grains were formed than particles added to the melt. The grains/particle efficiency varied from greater than one to nearly twenty as the size of the particle increased. This is attributed to the breaking up of particles into smaller particles by dissolution in the melt. For a given particle size, Ti-Al-Ta and Ti-Al-Nb particles were found to have a roughly similar grain/particle efficiency.
    Electronic ISSN: 1996-1944
    Topics: Mechanical Engineering, Materials Science, Production Engineering, Mining and Metallurgy, Traffic Engineering, Precision Mechanics
    Published by MDPI Publishing
    Location Call Number Expected Availability
    BibTip Others were also interested in ...
    PAPER CURRENT
  • 3
    facet.materialart.
    Unknown
    Copper substitution alone and in the presence of chromium, zinc, cadmium and lead in goethite (α-FeOOH) (2009)
    Mineralogical Society of Great Britain and Ireland
    Details
    Publication Date: 2009-09-01
    Description: A series of Cu-substituted goethites, single and co-substituted with Cr, Zn, Cd and/or Pb was prepared, having molar ratios equal to 2.00, 3.33 and 5.00 mol%. All the samples contained only goethite, except Cu-, (Cu,Zn)- and (Cu,Pb)-samples synthesized at 5.00 mol% where hematite was also formed. The presence of Cr/Cd suppressed the hematite-forming effects of Cu. The general sequence of metal entry into the single-metal-substituted goethites was Zn = Cr 〉 Cd 〉 Cu 〉 Pb and in di- (5.00 mol%) and tri- (3.33 mol%) metal-substituted goethites was Cu 〉 Zn 〉 Cd 〉 Cr 〉〉 Pb. Cu incorporation increased all the unit-cell parameters in single-metal-substituted goethite, and these parameters increased in combination with other metals as follows: Cd 〉 Zn 〉 Cr 〉 Pb in the multimetal-substituted goethites. The Cu-substituted goethite dissolved faster than pure goethite. Co substitutions of Cr/Pb reduced the dissolution rate (kFe), while substitutions of Cd/Zn increased kFe.
    Print ISSN: 0009-8558
    Electronic ISSN: 1471-8030
    Topics: Geosciences
    Published by Mineralogical Society of Great Britain and Ireland
    Location Call Number Expected Availability
    BibTip Others were also interested in ...
    PAPER CURRENT
Close ⊗
This website uses cookies and the analysis tool Matomo. More information can be found here...