ALBERT

Description: Two alternative approaches are developed to calculate blade-vortex interaction airloads on helicopter rotors: second order lifting-line theory, and a lifting surface theory correction. The common approach of using a larger vortex core radius to account for lifting-surface effects is quantified. The second order lifting-line theory also improves the modeling of yawed flow and swept tips. Calculated results are compared with wind tunnel measurements of lateral flapping, and with flight test measurements of blade section lift on SA349/2 and H-34 helicopter rotors. The tip vortex core radius required for good correlation with the flight test data is about 20 percent chord, which is within the range of measured viscous core sizes for helicopter rotors.

Description: The object of this investigation was to find and demonstrate a means of performing efficient finite-difference computations of rotor loading for a trimmed rotor in high-speed, forward flight. The essence of the scheme that was developed is a loose-coupled iteration procedure between a finite difference and a comprehensive integral rotor code. The coupling involves a transfer of appropriate load and inflow data on the advancing side between the two codes such that consistency maintained. Sample computations, including a limited comparison with model rotor data, are presented. The scheme converges rapidly. However, even one iteration with this scheme can provide sufficient accuracy for many purposes.

Description: The Mars Helicopter (MH) will be flying on the NASA Mars 2020 rover mission scheduled to launch in July of 2020. Research is being performed at the Jet Propulsion Laboratory (JPL) and NASA Ames Research Center to extend the current capabilities and develop the Mars Science Helicopter (MSH) as the next possible step for Martian rotorcraft. The low atmospheric density and the relatively small-scale rotors result in very low chord-based Reynolds number flows over the rotor airfoils. The low Reynolds number regime results in rapid performance degradation for conventional airfoils due to laminar separation without reattachment. Unconventional airfoil shapes with sharp leading edges are explored and optimized for aerodynamic performance at representative Reynolds-Mach combinations for a concept rotor. Sharp leading edges initiate immediate flow separation, and the occurrence of large-scale vortex shedding is found to contribute to the relative performance increase of the optimized airfoils, compared to conventional airfoil shapes. The oscillations are shown to occur independent from laminar-turbulent transition and therefore result in sustainable performance at lower Reynolds numbers. Comparisons are presented to conventional airfoil shapes and peak lift-to-drag ratio increases between 17% and 41% are observed for similar section lift.

Description: The viscous flow field near the surface of a hovering rotor blade was studied for blade twist distributions typical of a till rotor blade and a conventional helicopter rotor blade. Three blade geometries were studied, including a tilt rotor blade twist distribution (baseline), conventional helicopter rotor blade twist distribution, and the baseline twist distribution with 2 deg of precone. The results give insight into the delayed stall phenomenon often observed for highly twisted rotors. Calculations were performed for a high thrust condition near stall using the thin-layer Navier-Stokes CFD code TURNS. Effects of built-in twist on section force coefficients, skin friction, velocities, surface pressures, and boundary layer shape factor are discussed. Although the rotor thrust coefficient was nominally the same for the cases using the two twist distributions, large differences were found in the section in-plane and normal force coefficients. These preliminary results imply that the blade outboard region, rather than the inboard region, provides the majority of the performance advantage of the baseline case over the low twist case. Skin friction, velocities near the blade, and surface pressures for the two twist distributions reveal significant differences in the blade outboard region.

Description: This paper has two objectives. The first objective is to formulate a 3-dimensional Finite Element Model for the dynamic analysis of helicopter rotor blades. The second objective is to implement and analyze a dual-primal iterative substructuring based Krylov solver, that is parallel and scalable, for the solution of the 3-D FEM analysis. The numerical and parallel scalability of the solver is studied using two prototype problems - one for ideal hover (symmetric) and one for a transient forward flight (non-symmetric) - both carried out on up to 48 processors. In both hover and forward flight conditions, a perfect linear speed-up is observed, for a given problem size, up to the point of substructure optimality. Substructure optimality and the linear parallel speed-up range are both shown to depend on the problem size as well as on the selection of the coarse problem. With a larger problem size, linear speed-up is restored up to the new substructure optimality. The solver also scales with problem size - even though this conclusion is premature given the small prototype grids considered in this study.

Description: A slowed-rotor compound helicopter has been synthesized using the NASA Design and Analysis of Rotorcraft (NDARC) conceptual design software. An overview of the design process and the capabilities of NDARC are presented. The benefits of trading rotor speed, wing-rotor lift share, and trim strategies are presented for an example set of sizing conditions and missions.

Description: The NASA Design and Analysis of Rotorcraft (NDARC) software is an aircraft system analysis tool intended to support both conceptual design efforts and technology impact assessments. The principal tasks are to design (or size) a rotorcraft to meet specified requirements, including vertical takeoff and landing (VTOL) operation, and then analyze the performance of the aircraft for a set of conditions. For broad and lasting utility, it is important that the code have the capability to model general rotorcraft configurations, and estimate the performance and weights of advanced rotor concepts. The architecture of the NDARC code accommodates configuration flexibility; a hierarchy of models; and ultimately multidisciplinary design, analysis, and optimization. Initially the software is implemented with lowfidelity models, typically appropriate for the conceptual design environment. An NDARC job consists of one or more cases, each case optionally performing design and analysis tasks. The design task involves sizing the rotorcraft to satisfy specified design conditions and missions. The analysis tasks can include off-design mission performance calculation, flight performance calculation for point operating conditions, and generation of subsystem or component performance maps. For analysis tasks, the aircraft description can come from the sizing task, from a previous case or a previous NDARC job, or be independently generated (typically the description of an existing aircraft). The aircraft consists of a set of components, including fuselage, rotors, wings, tails, and propulsion. For each component, attributes such as performance, drag, and weight can be calculated; and the aircraft attributes are obtained from the sum of the component attributes. Description and analysis of conventional rotorcraft configurations is facilitated, while retaining the capability to model novel and advanced concepts. Specific rotorcraft configurations considered are single main-rotor and tailrotor helicopter; tandem helicopter; coaxial helicopter; and tiltrotors. The architecture of the code accommodates addition of new or higher-fidelity attribute models for a component, as well as addition of new components.