ALBERT

Beschreibung: The purpose of this in vitro study was to evaluate the microtensile bond strength of one-step self-etch adhesive to human dentin surface modified with air abrasion and sonic technique and to assess the morphological characteristics of the pretreated dentin surface. The occlusal enamel was removed to obtain a flat dentin surface for thirty-six human molar teeth. The teeth were randomly divided into three experimental groups (n = 12 per group), according to the pretreatment of the dentin: (1) control group, (2) air abrasion group, and (3) sonic preparation group. Microtensile bond strength test was performed on a universal testing machine. Two specimens from each experimental group were subjected to SEM examination. There was no statistically significant difference in bond strength between the three experimental groups (P 〉 0.05). Mean microtensile bond strength (MPa) values were 35.3 ± 12.8 for control group, 35.8 ± 13.5 for air abrasion group, and 37.7 ± 12.0 for sonic preparation group. The use of air abrasion and sonic preparation with one-step self-etch adhesive does not appear to enhance or impair microtensile bond strength in dentin.

Beschreibung: The purpose of this study was to evaluate the effects of the incorporation of hydroxyapatite (HA) derived from cuttlefish bone on the mechanical properties of glass ionomer cements (GIC). Fuji II LC and Fuji IX GP Extra (GC Corporation, Tokyo, Japan) were used in the study. There were four groups (n = 11–18) for each material: a group without the addition of HA particles and three groups modified by incorporation of 2, 5, and 10 wt% HA. The tests were performed on a universal testing machine (Shimadzu, Duisburg, Germany) and descriptive statistics, two-way analysis of variance (ANOVA) for the comparison of three mechanical properties, and one-way ANOVA for the comparison of different concentrations for each material were performed. Regarding the Fuji IX groups, compressive strength (CS) and flexural strength (FS) were highest in the group without HA particles added. The differences in CS between the Fuji IX group without HA particles and the Fuji IX groups with 2 wt% HA and 10 wt% HA were significant. The Fuji II 5 wt% HA group exhibited higher diametral tensile strength (DTS) and CS than other Fuji II groups, but not significantly. The Fuji II group, modified with 10 wt% HA, exhibited significantly higher FS than the Fuji II group without HA particles (p 〈 0.05). Porous HA incorporated into the Fuji IX groups had a significant impact on mechanical properties only in the Fuji IX 5 wt% HA group. Fuji II groups modified with 10 wt% HA showed the most favorable results with respect to FS.

Beschreibung: Prior research reveal that low-viscosity resin is able to significantly penetrate initial caries lesions, which leads to their stabilization. The objective of the present report is to assess the shear bond strength (SBS) of orthodontic brackets bonded with different adhesives to demineralized enamel treated with a low-viscosity resin infiltrant. It also aims to compare the achieved bond strengths to those achieved in relation to sound enamel (SE). A total of 48 newly extracted third molars were collected, distributed in four groups (n=12), covered with a nail varnish, with 4 x 4 mm of uncoated area, immersed in Buskes demineralizing solution (14 days, 37 °C) or remained untreated. Group I: SE + Transbond XT; Group II: demineralized enamel (DE) + ICON + Transbond XT; Group III: DE + ICON + Scotchbond Universal; Group IV: DE + ICON + Assure PLUS. SBS was quantified in megapascals (MPa) and statistically analyzed (ANOVA, p ≤ 0.05). The mode of failure was assessed microscopically (10 x magnification). The highest SBS detected was in Group IV, and the difference was statistically significant (F = 14.37; p = 0.000). Treatment with a resin infiltrant on DE does not impair the shear bond strength when compared to SE, although it does produce a significantly higher strength when combined with Assure PLUS.

Beschreibung: The aim of the study was to evaluate the effects of incorporation of Al2O3, ZrO2 and TiO2 nanoparticles into glass–ionomer cements (GICs). Two different GICs were used in the study. Four groups were prepared for each material: the control group (without nanoparticles) and three groups modified by the incorporation of nanoparticles at 2, 5 or 10 wt %, respectively. Cements were mixed and placed in moulds (4 mm × 6 mm); after setting, the samples were stored in saline (one day and one week). Compressive strengths were measured and the morphology of the fractured surfaces was analyzed by scanning electron microscopy. The elements released into the storage solutions were determined by Inductively coupled plasma-optical emission spectrometry (ICP-OES). Addition of nanoparticles was found to alter the appearance of cements as examined by scanning electron microscopy. Compressive strength increased with the addition of ZrO2 and especially TiO2 nanoparticles, whereas the addition of Al2O3 nanoparticles generally weakened the cements. The ion release profile of the modified cements was the same in all cases. The addition of Al2O3, ZrO2 and TiO2 nanoparticles into GICs is beneficial, since it leads to reduction of the microscopic voids in the set cement. Of these, the use of ZrO2 and TiO2 nanoparticles also led to increased compressive strength. Nanoparticles did not release detectable levels of ions (Al, Zr or Ti), which makes them suitable for clinical use.

Beschreibung: The purpose of the study was to determine the wear rate of Equia Forte HT Fil with Equia Forte Coat or without coating and compare it with Fuji IX GP high-viscosity glass ionomer cement (GIC) in conditions with acid load or at neutral pH. The samples were stored for 7 days: (1) in artificial saliva, (2) in artificial saliva and cyclically exposed to low pH, and (3) in distilled water and cyclically exposed to low pH. Wear was determined by measuring the difference in mass before and after brushing in an abrasion testing device. The wear of Fuji IX GP was significantly higher than that of Equia Forte HT Fil with or without coating (p = 0.000). The difference between Equia Forte HT Fil with and without Coat was not statistically significant (p 〈 0.803). The differences in wear resistance between samples stored in saliva and in distilled water were not significant (p = 0.588). Periodic exposure to the low pH solution significantly affected the wear resistance of all materials (p = 0.000). Equia Forte HT Fil was more resistant to wear than Fuji IX GP in all storage conditions. A resinous coat did not significantly increase wear resistance.

Beschreibung: This study aimed to determine the effects of three different varnish materials (containing casein phosphopeptide-amorphous calcium phosphate, nano-hydroxyapatite, and fluoride) on enamel. Thirty-three extracted human third molars were used for specimen preparation. These were demineralized using phosphoric acid. Three experimental groups (n = 11) were treated with 3M™ Clinpro™ White Varnish, MI Varnish®, and Megasonex® toothpaste, respectively, every twenty-four hours for fourteen days. Analysis of the microhardness of the specimens’ enamel surfaces was carried out via the Vickers method, and by scanning electron microscopy/energy dispersive X-ray spectroscopy (SEM/EDS). Analysis was performed at three stages: at baseline value, after demineralization, and after the period of remineralization. Data were subjected to Scheffe’s post hoc test. The mean microhardness values (HV0.1) obtained for the group of samples treated with MI Varnish® were higher compared with the other two groups (p = 0.001 for both comparisons), while the first and third groups did not differ significantly from each other (p = 0.97). SEM analysis showed uneven patterns and porosities on all samples tested. EDS results showed an increase in the mineral content of the examined samples, with the highest mineral content observed in the MI Varnish® group. It can be concluded that MI Varnish® use has a better remineralization effect on enamel than the other two materials.

Beschreibung: The contemporary approach for operative caries management emphasizes personalized interventions for each patient, dependent upon the individual’s caries susceptibility/risk, the stage of the carious lesion and its activity. The clinician’s challenge is to optimize the extent of cavity preparation and the choice of dental restorative biomaterials, appreciating the benefits offered by ion-releasing restorative materials. There is a growing application of bioactive/bio-interactive materials in minimally invasive operative dentistry, as they may help with tissue recovery by ion release. In case of moderate or extensive occlusal cavitation, the clinical criteria include the individual caries susceptibility and carious lesion activity. In high caries risk cases, ion-releasing biomaterials (IRB) can be used, as well as for active carious lesions. In proximal lesions, the clinical criteria include the individual caries susceptibility, the lesion activity and presence of cavities with little or no enamel at the gingival margin. This article aims to discuss the restorative ion-releasing options, according to different clinical situations, and the caries susceptibility to manage cavitated carious lesions in permanent adult teeth.