ALBERT

Notes: Abstract The ridge located between 31° S and 34°30′S is spreading at a rate of 35 mm yr−1, a transitional velocity between the very slow (≤20 mm yr−1) opening rates of the North Atlantic and Southwest Indian Oceans, and the intermediate rates (60 mm yr−1) of the northern limb of the East Pacific Rise, and the Galapagos and Juan de Fuca Ridges. A synthesis of multi-narrow beam, magnetics and gravity data document that in this area the ridge represents a dynamically evolving system. Here the ridge is partitioned into an ensemble of six distinct segments of variable lengths (12 to 100 km) by two transform faults (first-order discontinuities) and three small offset (〈 30 km) discontinuities (second-order discontinuities) that behave non-rigidly creating complex and heterogeneous morphotectonic patterns that are not parallel to flow lines. The offset magnitudes of both the first and second-order discontinuities change in response to differential asymmetric spreading. In addition, along the fossil trace of second-order discontinuities, the lengths of abyssal hills located to either side of a discordant zone are observed to lengthen and shorten creating a saw-toothed pattern. Although the spreading rate remains the same along the length of the ridge studied, the morphology of the spreading segments varies from a deep median valley with characteristics analogous to the rift segments of the North Atlantic to a gently rifted axial bulge that is indistinguishable from the shape and relief of the intermediate rate spreading centers of the East Pacific Rise (i.e., 21°N). Like other carefully surveyed ridge segments at slow and fast rates of accretion, the along-axis profiles of each ridge segment are distinctly convex upwards, and exhibit along-strike changes in relief of 500m to 1500 between the shallowest portion of the segment (approximate center) and the segment ends. Such spatial variations create marked along-axis changes in the morphology and relief of each segment. A relatively low mantle Bouguer anomaly is known to be associated with the ridge segment characterized by a gently rifted axial bulge and is interpreted to indicate the presence of focused mantle upwelling (Kuo and Forsyth, 1988). Moreover, the terrain at the ends of each segment are known to be highly magnetized compared to the centers of each segment (Carbotte et al, 1990). Taken together, these data clearly establish that these profound spatial variations in ridge segment properties between adjoining segments, and along and across each segment, indicate that the upper mantle processes responsible for the formation of this contrasting architecture are not solely related to passive upwelling of the asthenosphere beneath the ridge axis. Rather, there must be differences in the thermal and mechanical structure of the crust and upper mantle between and along the ridge segments to explain these spatial variations in axial topography, crustal structure and magnetization. These results are consistent with the results of investigations from other parts of the ridge and suggest that the emplacement of magma is highly focused along segments and positioned beneath the depth minimum of a given segment. The profound differences between segments indicate that the processes governing the behavior of upwelling mantle are decoupled and the variations in the patterns of axis flanking morphology and rate of accretion indicate that processes controlling upwelling and melt production vary markedly in time as well. At this spreading rate and in this area, the accretionary processes are clearly three-dimensional. In addition, the morphology of a ridge segment is not governed so much by opening rate as by the thermal structure of the mantle which underlies the segment.

Notes: Abstract Continuous along-axis Sea Beam coverage of the slow-intermediate spreading (34–38 mm yr−1 full rate) southern Mid-Atlantic Ridge (25°–27°30′S and 31°–38° S) shows that the ridge axis is segmented by both rigid and non-rigid discontinuities. Following the model of Macdonald et al. (1988b), a hierarchy of four orders is proposed for ridge axis discontinuities based on a continuum of relative age and distance offset across the discontinuites. This paper discusses the characteristics associated with five second-order discontinuities found in the areas surveyed. First-order discontinuities represent rigid offsets, transform faults, whereas non-rigid discontinuities fall into the second, third and fourth orders. Like transform fault boundaries, second-order discontinuities have distinctive morphologic signatures both on and off-axis-discordant zones — and therefore are better defined than third- or fourth-order discontinuities. Second-order discontinuities are offsets that range in distance from less than 10 km to approximately 30 km and vary in age offset from 0.5 to approximately 2.0 m.y. The variable morphotectonic geometries associated with these discontinuities indicate that horizontal shear strains are accommodated by both extensional and strike-slip tectonism and that the geometries are unstable in time. Three characteristic geometries are recognized: (1)en echelon jog in the plate boundary where ridge axis tips overlap slightly, (2)en echelon jog in the plate boundary where ridge axes are separated by an extensional basin whose long axis is oriented parallel to the strike of the adjoining ridge axes, and (3) oblique offset characterized by a large extensional basin that is oriented approximately 45° to the strike of the ridge axes. In the case of the third type, evidence for short strands of strike-slip tectonism that link an obliquely oriented extensional basin flanking ridge tips is often apparent. Analysis of the detailed bathymetric and magnetic data collected over the second-order discontinuities and their off axis terrain out to 5–7 m.y. documents that second-order discontinuities can follow several evolutionary paths: they can evolve from transform fault boundaries through prolonged asymmetric spreading, they may migrate along strike leaving a V-shaped wake, and they may remain in approximately the same position but oscillate slightly back and forth. In addition, a small change in the pole of relative motion occurring 4–5 Ma is thought to have resulted in the initiation of at least one second-order discontinuity in the survey area. A geologic model is proposed which involves the interplay of lithospheric thickness, asymmetric spreading, temporal and spatial variability of along-axis magmatic input and changes in the poles of relative motion to explain the origin, morphology and evolution of second-order ridge axis discontinuities.