ALBERT

Description: The goal of this work is to enable the computation of large numbers of unsteady high-fidelity flow simulations for a YAV-8B Harrier aircraft in ground effect by improving the solution process and taking advantage of NASA parallel supercomputers. The YAV-8B Harrier aircraft can take off and land vertically, or utilize short runways by directing its four exhaust nozzles toward the ground. Transition to forward flight is achieved by rotating these nozzles into a horizontal position.

Description: This viewgraph presentation reviews NASA's Columbia supercomputer and the mesh technology used to test the adequacy of the fluid and cooling of a computer room. A technical description of the Columbia supercomputer is also presented along with its performance capability.

Description: With the increasing presence of unmanned aircraft systems (UAS), or drones, in the national airspace, the management for access and operation of these vehicles is required. NASAs management approach is being developed under the unmanned aircraft system traffic management (UTM) program. To determine the aerodynamic characteristics of drones, wind tunnel experiments and computation fluid dynamic (CFD) analysis have been conducted. These experiments and analyses are undertaken to understand the flight capabilities of these vehicles in variable head and cross wind conditions. The results of these investigations will provide metrics for the safe operation of these vehicles in and around civil populations and in urban settings. The focus of this paper is to model a drone installed in a wind tunnel for varying pitch attitudes and rotor rpm settings. Specifically, the IRIS drone is modeled in the NASA-Ames 7x10 ft wind tunnel. The tunnel mounting hardware and the tunnel enclosure are modeled along with the IRIS drone geometry. The rotors of the drone are modeled using two methodologies: a rotor disk model and full rotating rotors with moving grids. The results of the analysis are compared with available experimental data to validate the computational approach.

Description: Rocket and missile firings from attack helicopters can cause main engine compressor stall. Studies of this phenomenon suggest that the main engine ingests either the plume from the rockets or the rocket blast waves. This creates surges at the inlet face, causing a loss of power in the main engine. The objective of this project is to set-up a computational fluid dynamics (CFD) simulation of the AH-64D Apache Longbow helicopter during a rocket launch, in order to qualitatively study the fluid dynamics of the problem. This project presents a progression of three unsteady Navier-Stokes solutions. The first unsteady solution involves only a rocket launch from its launch canister. The second solution is a launch from a canister mounted on the Apache's wing-pylon assembly. The last solution includes the Apache main engine and fuselage. The computations use a series of structured, overset grid systems, which allow for a rocket moving in a prescribed path. The method implements a Roe upwind scheme with LU-SGS (lower-upper factored symmetric Gauss-Seidel). A rotor pressure disk model approximates the helicopter rotor, while the rocket engine exit properties are applied as a prescribed boundary condition. Although the project is only at the half-way point, the first and second CFD simulations suggest the possibility of pressure wave interference. Sudden surges in pressure occur from two sources: at rocket start-up, and as the rocket leaves the canister. Wave patterns set-up by these sources appear to propagate to the location of the engine inlet. However the simplified geometry simulation with the main engine needs to be performed before coming to a conclusion.

Description: This paper will use high-resolution Navier-Stokes computational fluid dynamics (CFD) simulations to model the near-wake vortex roll-up behind rotor blades. The locations and strengths of the trailing vortices will be determined from newly-developed visualization and analysis software tools applied to the CFD solutions. Computational results for rotor nearwake vortices will be used to study the near-wake vortex roll up for highly-twisted tiltrotor blades. These rotor blades typically have combinations of positive and negative spanwise loading and complex vortex wake interactions. Results of the computational studies will be compared to vortex-lattice wake models that are frequently used in rotorcraft comprehensive codes. Information from these comparisons will be used to improve the rotor wake models in the Tilt-Rotor Acoustic Code (TRAC) portion of NASA's Short Haul Civil Transport program (SHCT). Accurate modeling of the rotor wake is an important part of this program and crucial to the successful design of future civil tiltrotor aircraft. The rotor wake system plays an important role in blade-vortex interaction noise, a major problem for all rotorcraft including tiltrotors.

Description: A new software tool, AeroDB, is used to compute thousands of Euler and Navier-Stokes solutions for a 2nd generation glide-back booster in one week. The solution process exploits a common job-submission grid environment using 13 computers located at 4 different geographical sites. Process automation and web-based access to the database greatly reduces the user workload, removing much of the tedium and tendency for user input errors. The database consists of forces, moments, and solution files obtained by varying the Mach number, angle of attack, and sideslip angle. The forces and moments compare well with experimental data. Stability derivatives are also computed using a monotone cubic spline procedure. Flow visualization and three-dimensional surface plots are used to interpret and characterize the nature of computed flow fields.

Description: The Harrier YAV-8B aircraft is capable of vertical and short-field take-off and landing (V/STOL) by directing its four exhaust nozzles toward the ground, or conventional flight by rotating its nozzles into a horizontal position. The British Royal Air Force and the United States Marine Corps have used this aircraft for more than 30 years to provide a quick reaction time for troop support, and reduce the need for long runways. The success of this powered-lift (PL) vehicle has also prompted the more recent design of the Joint Strike Fighter (JSF). However there are significant safety issues that must be addressed when operating a PL vehicle in close proximity to the ground. Hot Gas Ingestion (HGI) by the inlets can result in a rapid loss of powered lift; and high-speed jet flows along the ground plane can induce low pressures underneath the vehicle, causing a 'suck-down' effect. Under these conditions, departure from controlled flight may occur. Moreover, unsteady ground vortices and jet fountains can affect the aircraft,s controllability and its proximity to ground troops. The viscous, time-dependent flow fields of PL vehicles are difficult to accurately and efficiently predict using Computational Fluid Dynamics (CFD). A number of researchers have used the time-dependent Reynolds-averaged Navier-Stokes (RANS) equations to compute flows for single and multiple jets in a cross-flow. A few have added some geometric complexity to the problem by computing flows for jet-augmented delta wings near a ground plane. Smith et.al. computed for the first time a single RANS solution about a simplified Harrier. This geometry included a fuselage, wing, leading edge root extension (LERX), inlets, and exhaust nozzles. All of these investigations cite two practical problems with computing these flows: 1) the need for improved solution accuracy; and, 2) the need for faster solution methods. We view the need for faster solution methods as key to improving the solution accuracy and making this class of computation more routine. One can hardly refine grids, explore the use of advanced turbulence models, and generate databases when it takes weeks of dedicated computer time for a single solution. Chaderjian, Ahmad, Pandya, and Murman have focused on reducing the time-to-solution for this very difficult and complex problem through process automation and exploitation of parallel computing. They began with the Harrier geometry reported, and added a deflected wing flap and empennage for greater realism. To date more than 80 solutions have been carried out. This paper will describe this process and progress made in reducing the time required to generate a simple longitudinal force and moment database for a Harrier in ground effect. It shows a typical snap-shot from an unsteady streakline animation, where fluid particles are colored by temperature. The ground vortex and a jet-fountain vortex are highlighted. It also shows a similar streakline image, where HGI occurs due to the vehicle in close proximity to the ground. It is show the mean lift coefficient as a function of angle of attack and height. The angle of attack range was 4 deg less than or = alpha less than or = 10 deg with an increment of 1 degree, and the height range was 10 ft less than or = h less than or = 30ft with an increment of 5 feet. This 35 solution database was extended to over 2500 cases using a monotone cubic-spline interpolation procedure. The suck-down effect (reduction of lift near the ground) is highlighted in the figure. The "cushion effect," the conventional reduction of lift as the vehicle moves out of ground effect, is also indicated. All 35 RANS solutions were obtained using 952 Silicon Graphics Origin 2000 and 3000 processors in dedicated mode for one week. Typically, 112 processors were assigned to each case. Some other cases used fewer processors to utilize all available CPUS. The final paper will report on the automation of the solution process, including: grid generation, job monitoring, solution completion criteria, and post processing. Moreover, improvements in parallel efficiency for a dual time-step algorithm for the RANS equations will also be presented. Results will be discussed in detail using unsteady streakline flow visualization to correlate unsteady flow structures with dominant aerodynamic frequencies. The stability derivatives, CL, and CL, will also be presented.

Description: Helicopter flowfields are highly unsteady, nonlinear and three-dimensional. In forward flight and in hover, the rotor blades interact with the tip vortex and wake sheet developed by either itself or the other blades. This interaction, known as blade-vortex interactions (BVI), results in unsteady loading of the blades and can cause a distinctive acoustic signature. Accurate and cost-effective computational fluid dynamic solutions that capture blade-vortex interactions can help rotor designers and engineers to predict rotor performance and to develop designs for low acoustic signature. Such a predictive method must preserve a blade's shed vortex for several blade revolutions before being dissipated. A number of researchers have explored the requirements for this task. This paper will outline some new capabilities that have been added to the NASA Ames' OVERFLOW code to improve its overall accuracy for both vortex capturing and unsteady flows. To highlight these improvements, a number of case studies will be presented. These case studies consist of free convection of a 2-dimensional vortex, dynamically pitching 2-D airfoil including light-stall, and a full 3-D unsteady viscous solution of a helicopter rotor in forward flight In this study both central and upwind difference schemes are modified to be more accurate. Central difference scheme is chosen for this simulation because the flowfield is not dominated by strong shocks. The feature of shock-vortex interaction in such a flow is less important than the dominant blade-vortex interaction. The scheme is second-order accurate in time and solves the thin-layer Navier-Stokes equations in fully-implicit manner at each time-step. The spatial accuracy is either second and fourth-order central difference or third-order upwind difference using Roe-flux and MUSCLE scheme. This paper will highlight and demonstrate the methods for several sample cases and for a helicopter rotor. Preliminary computations on a rotor were performed by using this method and are in the process of documentation.