ALBERT

Description: The aerodynamic characteristics of a Circulation Control Wing (CCW) airfoil have been numerically investigated, and comparisons with experimental data have been made. The configuration chosen was a supercritical airfoil with a 30 degree dual-radius CCW flap. Steady and pulsed jet calculations were performed. It was found that the use of steady jets, even at very small mass flow rates, yielded a lift coefficient that is comparable or superior to conventional high-lift systems. The attached flow over the flap also gave rise to lower drag coefficients, and high L/D ratios. Pulsed jets with a 50% duty cycle were also studied. It was found that they were effective in generating lift at lower reduced mass flow rates compared to a steady jet, provided the pulse frequency was sufficiently high. This benefit was attributable to the fact that the momentum coefficient of the pulsed jet, during the portions of the cycle when the jet was on, was typically twice as much as that of a steady jet.

Description: This research effort is directed towards an examination of issues involved in porting large computational fluid dynamics codes in use within the industry to a distributed computing environment. This effort addresses strategies for implementing the distributed computing in a device independent fashion and load balancing. A flow solver called TEAM presently in use at Lockheed Aeronautical Systems Company was acquired to start this effort. The following tasks were completed: (1) The TEAM code was ported to a number of distributed computing platforms including a cluster of HP workstations located in the School of Aerospace Engineering at Georgia Tech; a cluster of DEC Alpha Workstations in the Graphics visualization lab located at Georgia Tech; a cluster of SGI workstations located at NASA Ames Research Center; and an IBM SP-2 system located at NASA ARC. (2) A number of communication strategies were implemented. Specifically, the manager-worker strategy and the worker-worker strategy were tested. (3) A variety of load balancing strategies were investigated. Specifically, the static load balancing, task queue balancing and the Crutchfield algorithm were coded and evaluated. (4) The classical explicit Runge-Kutta scheme in the TEAM solver was replaced with an LU implicit scheme. And (5) the implicit TEAM-PVM solver was extensively validated through studies of unsteady transonic flow over an F-5 wing, undergoing combined bending and torsional motion. These investigations are documented in extensive detail in the dissertation, 'Computational Strategies for Three-Dimensional Flow Simulations on Distributed Computing Systems', enclosed as an appendix.

Description: The sectional and total aerodynamic load characteristics and performance degradation of swept wings and helicopter rotors have been studied using a three-dimensional, compressible Navier-Stokes solver. Correlations of predictions with experimental data for swept wings with and without leading-edge ice formation show the ability of the present computational technique to accurately predict both the distributed surface pressures and integrated sectional loads. The leading-edge flow separation and reattachment on the wing surface associated with the leading-edge ice are also captured well showing a vortex formation and the spanwise migration of the flow inside the separated flow region. In the case of the helicopter rotors in hover, the rotor thrust loss and the torque penalties due to the leading-edge ice formation are numerically demonstrated.

Description: An efficient solution procedure has been developed for analyzing inviscid unsteady flow past counter rotating propellers. This scheme is first order accurate in time and second order in space, and has been extended to fourth order accuracy in the axial direction. The solution procedure has been applied to a 2-bladed SR-7 single rotation propeller and to a GE F7/A7 counter rotation propeller. The pressure coefficients and the global quantities, power and thrust, show good comparison with experimental measurements.

Description: The aerodynamic load characteristics and the performance degradation of moderate aspect ratio wings and rotors with simulated glaze leading-edge ice have been studied using a three-dimensional, compressible Navier-Stokes solver. The effect of a splitter plate at the wing root on both clean and iced wing configurations has been studied and the results are compared with the experiment. A significant difference has been observed with and without splitter plates in the magnitude of flow separation and aerodynamic loading at the inboard stations for the iced wing at 8-deg angle of attack. Inviscid calculations were performed and compared with viscous calculations to investigate whether the performance of iced swept wings can be inexpensively predicted using Euler methods. It is shown that inviscid calculations predict higher aerodynamic loading than viscous calculations, and cannot model separation effects. A typical nonlifting helicopter rotor in forward flight condition is also studied, and the penalty due to the leading-edge ice formation on the required torque is numerically demonstrated.

Description: The work done under this project was documented in detail as the Ph. D. dissertation of Dr. Duane Hixon. The objectives of the research project were evaluation of the generalized minimum residual method (GMRES) as a tool for accelerating 2-D and 3-D unsteady flows and evaluation of the suitability of the GMRES algorithm for unsteady flows, computed on parallel computer architectures.

Description: Circulation Control Wing (CCW) technology is a very effective way of achieving very high lift coefficients needed by aircraft during take-off and landing. This technology can also be used to directly control the flow field over the wing. Compared to a conventional high-lift system, a Circulation Control Wing (CCW) can generate the required values of lift coefficient C(sub L,max) during take-off/landing with fewer or no moving parts and much less complexity. Earlier designs of CCW configurations used airfoils with a large radius rounded trailing edge to maximize the lift benefit. However, these designs also produced very high drag. These high drag levels associated with the blunt, large radius trailing edge can be prohibitive under cruise conditions when Circulation Control is no longer necessary. To overcome this difficulty, an advanced CCW section, i.e., a circulation hinged flap was developed to replace the original rounded trailing edge CC airfoil. This concept developed by Englar is shown. The upper surface of the CCW flap is a large-radius arc surface, but the lower surface of the flap is flat. The flap could be deflected from 0 degrees to 90 degrees. When an aircraft takes-off or lands, the flap is deflected as in a conventional high lift system. Then this large radius on the upper surface produces a large jet turning angle, leading to high lift. When the aircraft is in cruise, the flap is retracted and a conventional sharp trailing edge shape results, greatly reducing the drag. This kind of flap does have some moving elements that increase the weight and complexity over an earlier CCW design. But overall, the hinged flap design still maintains most of the Circulation Control high lift advantages, while greatly reducing the drag in cruising condition associated with the rounded trailing edge CCW design. In the present work, an unsteady three-dimensional Navier-Stokes analysis procedure has been developed and applied to this advanced CCW configuration. The solver can be used in both a 2-D and a 3-D mode, and can thus model airfoils as well as finite wings. The jet slot location, slot height, and the flap angle can all be varied easily and individually in the grid generator and the flow solver. Steady jets, pulsed jets, the leading edge and trailing edge blowing can all be studied with this solver.

Description: The sectional and total aerodynamics load characteristics of moderate aspect ratio wings with and without simulated glaze leading-edge ice are studied using a three-dimensional, compressible Navier-Stokes solver. The wing has an untwisted, untapered planform shape with NACA 0012 airfoil section. The aspect ratio of the wing is chosen to be 5. Comparisons of computed surface pressures and sectional loads with experimental data for identical configurations are given. The abrupt decrease in the wing stall angle as a result of the leading edge ice formation is numerically demonstrated.

Description: Helicopters in high-speed forward flight usually experience large regions of dynamic stall over the retreating side of the rotor disk. The rapid variations in the lift and pitching moments associated with the stall process can result in vibratory loads, and can cause fatigue and failure of pitch links. In some instances, the large time lag between the aerodynamic forces and the blade motion can trigger stall flutter. A number of techniques for the alleviation of dynamic stall have been proposed and studied by researchers. Passive and active control techniques have both been explored. Passive techniques include the use of high solidity rotors that reduce the lift coefficients of individual blades, leading edge slots and leading edge slats. Active control techniques include steady and unsteady blowing, and dynamically deformable leading edge (DDLE) airfoils. Considerable amount of experimental and numerical data has been collected on the effectiveness of these concepts. One concept that has not received as much attention is the drooped-leading edge airfoil idea. It has been observed in wind tunnel studies and flight tests that drooped leading edge airfoils can have a milder dynamic stall, with a significantly milder load hysteresis. Drooped leading edge airfoils may not, however, be suitable at other conditions, e.g. in hover, or in transonic flow. Work needs to be done on the analysis and design of drooped leading edge airfoils for efficient operation in a variety of flight regimes (hover, dynamic stall, and transonic flow). One concept that is worthy of investigation is the dynamically drooping airfoil, where the leading edge shape is changed roughly once-per-rev to mitigate the dynamic stall.