ALBERT

Description: The objectives of this study are threefold: (1) Provide insight into water delivery in microgravity and determine optimal germination paper wetting for subsequent seed germination in microgravity; (2) Observe the behavior of water exposed to a strong localized magnetic field in microgravity; and (3) Simulate the flow of fixative (using water) through the hardware. The Magnetic Field Apparatus (MFA) is a new piece of hardware slated to fly on the Space Shuttle in early 2001. MFA is designed to expose plant tissue to magnets in a microgravity environment, deliver water to the plant tissue, record photographic images of plant tissue, and deliver fixative to the plant tissue.

Description: Few mode optical fibers have been shown to produce predictable interference patterns when placed under strain. The use is described of a modal domain sensor in a vibration control experiment. An optical fiber is bonded along the length of a flexible beam. Output from the modal domain sensor is used to suppress vibrations induced in the beam. A distributed effect model for the modal domain sensor is developed. This model is combined with the beam and actuator dynamics to produce a system suitable for control design. Computer simulations predict open and closed loop dynamic responses. An experimental apparatus is described and experimental results are presented.

Description: The analytic and experimental performance of optical fiber sensors for the control of vibration of large aerospace and other structures are investigated. In particular, model domain optical fiber sensor systems, are being studied due to their apparent potential as distributed, low mass sensors of vibration over appropriate ranges of both low frequency and low amplitude displacements. Progress during the past three months is outlined. Progress since September is divided into work in the areas of experimental hardware development, analytical analysis, control design and sensor development. During the next six months, tests of a prototype closed-loop control system for a beam are planned which will demonstrate the solution of several optical fiber instrumentation device problems, the performance of the control system theory which incorporates the model of the modal domain sensor, and the potential for distributed control which this sensor approach offers.

Description: This experiment was conducted as part of a risk mitigation payload aboard the Space Shuttle Atlantis on STS-101. The objectives were to test a newly developed water delivery system, and to determine the optimal combination of water volume and substrate for the imbibition and germination of flax (Linum usitatissimum) seeds in space. Two different combinations of germination paper were tested for their ability to absorb, distribute, and retain water in microgravity. A single layer of thick germination paper was compared with one layer of thin germination paper under a layer of thick paper. Paper strips were cut to fit snugly into seed cassettes, and seeds were glued to them with the micropyle ends pointing outward. Water was delivered in small increments that traveled through the paper via capillary action. Three water delivery volumes were tested, with the largest (480 microliters) outperforming the 400 microliters and 320 microliters volumes for percent germination (90.6%) and root growth (mean=4.1 mm) during the 34-hour spaceflight experiment. The ground control experiment yielded similar results, but with lower rates of germination (84.4%) and shorter root lengths (mean=2.8 mm). It is not clear if the roots emerged more quickly in microgravity and/or grew faster than the ground controls. The single layer of thick germination paper generally exhibited better overall growth than the two layered option. Significant seed position effects were observed in both the flight and ground control experiments. Overall, the design of the water delivery system, seed cassettes and the germination paper strip concept was validated as an effective method for promoting seed germination and root growth under microgravity conditions. c2003 COSPAR. Published by Elsevier Ltd. All rights reserved.

Description: A computational study of the wing for the distributed electric propulsion X-57 Maxwell airplane configuration at cruise and takeoff/landing conditions was completed. Three unstructured-mesh, Navier-Stokes computational fluid dynamics methods, FUN3D, USM3D and Kestrel, were used to predict the performance buildup of components to the full X-57 configuration. The goal of the X-57 wing and distributed electric propulsion system design was to meet or exceed the required lift coefficient of 3.95 for a stall speed of 58 knots. The X-57 Maxwell airplane was designed with a small, high aspect ratio cruise wing that was designed for a high cruise lift coefficient of 0.75 at a cruise speed of 150 knots and altitude of 8,000 ft, with an angle of attack of approximately 0deg. The computational data indicates that the X-57 full aircraft drag would meet the cruise drag goal with a 25 count drag margin. The cruise configuration maximum lift coefficient is 2.07 and without including the stabilator is 1.86 at an angle of attack of 14 deg, predicted with the USM3D flow solver using the Spalart-Allmaras turbulence model. The maximum lift coefficient for the high-lift wing (with the 30deg flap deflection) without the stabilator contribution is 2.60 at an angle of attack of 13 deg. For high-lift blowing conditions with 13.7 hp/prop, the maximum lift coefficient excluding the stabilator is 4.426 at (alpha) = 13 deg. Therefore, the lift augmentation from the high-lift propellers is 1.7 and the total lift augmentation from the high-lift system (30 deg flap deflection and the high-lift blowing) is 2.38. The drag for the high-lift wing with 30 deg flap deflection is much higher than the cruise wing configuration, but the high-lift system is used only during a small portion of the flight envelope. The pitching moment is relatively constant for both blown and unblown conditions when the stabilator is excluded. Modeling the full geometry has indicated some adverse effects from the fuselage on the wing and stabilator. At high angles of attack, the solutions with the USM3D flow solver using the Spalart-Allmaras turbulence model indicates large flow separation on the wing upper surface between the two high-lift nacelles near the fuselage, and also a reduction in sectional lift on the stabilator in the first 50 percent of the stabilator semispan. However, the large flow separation near the fuselage is mostly eliminated in the solutions predicted with two codes, USM3D and Kestrel, using Hybrid Reynolds-averaged Navier Stokes/Large Eddy Simulation turbulence models.