ALBERT

Description: Aerodynamic assessment of icing effects on swept wings is an important component of a larger effort to improve three-dimensional (3D) icing simulation capabilities. An understanding of ice-shape geometric fidelity and Reynolds and Mach number effects on the iced-wing aerodynamics is needed to guide the development and validation of ice-accretion simulation tools. To this end, wind tunnel testing was carried out for a 13.3-percent-scale semispan wing based upon the Common Research Model airplane configuration. The wind tunnel testing was conducted at the Office National dEtudes et de Recherches Arospatiales (ONERA) F1 pressurized wind tunnel with Reynolds numbers of 1.6 x 10(exp 6) to 11.9 x 10(exp 6 ) and Mach numbers of 0.09 to 0.34. Five different configurations were investigated using fully 3D, high-fidelity artificial ice shapes that maintain nearly all of the 3D ice-accretion features documented in prior icing wind tunnel tests. These large, leading-edge ice shapes were nominally based upon airplane holding in icing conditions scenarios. For three of these configurations, lower fidelity simulations were also built and tested. The results presented in this paper show that while Reynolds and Mach number effects are important for quantifying the clean-wing performance, there is very little to no effect for an iced wing with 3D, high-fidelity artificial ice shapes or 3D smooth ice shapes with grit roughness. These conclusions are consistent with the large volume of past research on iced airfoils. However, some differences were also noted for the associated stalling angle of the iced swept wing and for various lower fidelity versions of the leading-edge ice accretion. More research is planned to further investigate the key features of ice-accretion geometry that must be simulated in lower fidelity versions in order to capture the essential aerodynamics.

Description: Understanding the aerodynamic impact of swept-wing ice accretions is a crucial component of the design of modern aircraft. Computer-simulation tools are commonly used to approximate ice shapes, so the necessary level of detail or fidelity of those simulated ice shapes must be understood relative to high-fidelity representations of the ice. Previous tests were performed in the NASA Icing Research Tunnel to acquire high-fidelity ice shapes. From this database, full-span artificial ice shapes were designed and manufactured for both an 8.9%-scale and 13.3%-scale semispan wing model of the CRM65 which has been established as the full-scale baseline for this swept-wing project. These models were tested in the Walter H. Beech wind tunnel at Wichita State University and at the ONERA F1 facility, respectively. The data collected in the Wichita St. University wind tunnel provided a low-Reynolds number baseline study while the pressurized F1 facility produced data over a wide range of Reynolds and Mach numbers with the highest Reynolds number studied being approximately Re=11.9x106. Past work focused on only three different fidelity variations for ice shapes based on multiple icing conditions. This work presents a more detailed investigation into several fidelity representations of a single highly three-dimensional scallop ice accretion. Sensitivity to roughness size and application technique on a low-fidelity smooth ice shape is described. The data indicate that the aerodynamic performance is not especially sensitive to the grit variations. An ice accretion code was also used to generate ice shapes for aerodynamic testing and comparisons. These ice shapes have a general appearance like the low-fidelity smooth ice shapes, but in this case, the computer-generated ice shape is significantly smaller. As such, the impact of that ice shape on the aerodynamic performance of the wing is reduced compared to the smooth ice shape based on the icing experiment for those same conditions. Spanwise discontinuities were also introduced to a low-fidelity ice shape in an attempt to quantify the impact of those variation in the high-fidelity ice shape. While the lift data indicate good agreement between the high-fidelity ice shapes and the low-fidelity ice shapes and the low-fidelity ice shapes with spanwise discontinuities, a closer investigation of the data suggests potential, significant differences in the flowfield. These results were similar at both facilities over the wide range of test conditions utilized.

Description: A test was conducted at NASA Icing Research Tunnel to evaluate altitude scaling methods for thermal ice protection system. Two scaling methods based on Weber number were compared against a method based on the Reynolds number. The results generally agreed with the previous set of tests conducted in NRCC Altitude Icing Wind Tunnel. The Weber number based scaling methods resulted in smaller runback ice mass than the Reynolds number based scaling method. The ice accretions from the Weber number based scaling method also formed farther upstream. However there were large differences in the accreted ice mass between the two Weber number based scaling methods. The difference became greater when the speed was increased. This indicated that there may be some Reynolds number effects that isnt fully accounted for and warrants further study.