ALBERT

Description: Liquid Xe filled single wire proportional and multiple wire ionization chambers, measuring gain and time/spatial resolution properties

Description: We present a new technique for the correction of atmospheric distortion in telescope images. Most of this distortion arises from a random phase variation of the incoming light across the telescope aperture. This variation limits the resolving power of even large telescopes to about one arc second. If the sharpness of the images is defined in a suitable way, this sharpness is maximized only when the phase distortion of the incoming light is zero. We present computer simulations of a simple feedback system in which active optical elements, set to maximize the sharpness, correct most of the atmospheric distortion. Photon statistics set the limiting magnitude of the object for which a practical feedback system can work. Details in a sixth magnitude object smaller than 0.1 sec of arc should be resolvable. The system can be conveniently employed within existing telescopes.

Description: Anisotropy has been detected in the cosmic blackbody radiation with a 33-GHz (0.9 cm) twin-antenna Dicke radiometer flown to an altitude of 20 km aboard a U-2 aircraft. In data distributed over two-thirds of the Northern Hemisphere, an anisotropy is observed, which is well fitted by a first-order spherical harmonic with an amplitude of (3.5 plus or minus 0.6) x 10 to the -3rd deg K, and direction 11.0 plus or minus 0.6 h right ascension and 6 plus or minus 10 deg declination. This observation is readily interpreted as due to motion of the earth relative to the radiation with a velocity of 390 plus or minus 60 km/sec.

Description: Complex computer generated phase holograms (CGPH's) have been fabricated in PMMA by partial e-beam exposure and subsequent partial development. The CGPH was encoded as a sequence of phase delay pixels and written by the JEOL JBX-5D2 E-beam lithography system, a different dose being assigned to each value of phase delay. Following carefully controlled partial development, the pattern appeared rendered in relief in the PMMA, which then acts as the phase-delay medium. The exposure dose was in the range 20-200 micro-C/sq cm, and very aggressive development in pure acetone led to low contrast. This enabled etch depth control to better than plus or minus lambda(sub vis)/60. That result was obtained by exposing isolated 50 micron square patches and measuring resist removal over the central area where the proximity effect dose was uniform and related only to the local exposure. For complex CGPH's with pixel size of the order of the e-beam proximity effect radius, the patterns must be corrected for the extra exposure caused by electrons scattered back up out of the substrate. This has been accomplished by deconvolving the two-dimensional dose deposition function with the desired dose pattern. The deposition function, which plays much the same role as an instrument response function, was carefully measured under the exact conditions used to expose the samples. The devices fabricated were designed with 16 equal phase steps per retardation cycle, were up to 1 cm square, and consisted of up to 100 million 0.3-2.0 micron square pixels. Data files were up to 500 MB long and exposure times ranged to tens of hours. A Fresnel phase lens was fabricated that had diffraction limited optical performance with better than 85 percent efficiency.

Description: A new type of gamma-ray camera is discussed that makes use of electron avalanches in liquid xenon and is currently under development. It is shown that such a radioisotope camera promises many advantages over any other existing gamma-ray cameras. Spatial resolution better than 1 mm and counting rates higher than one million C/sec are possible. An energy resolution of 11% FWHM has recently been achieved with a collimated Hg-203 source using a parallel-plate ionization chamber containing a Frisch grid.

Description: The properties of convex gratings fabricated by electron-beam lithography are investigated. Three grating types are shown. These gratings allow the optical designer to fully realize the considerable advantages of concentric spectrometer forms.

Description: Light scattering off particles flowing through a two-slit interference pattern can be used to measure the shear stress of the fluid. We have designed and fabricated a miniature diffractive optic sensor based on this principle.

Description: Diffractive optical elements fabricated on flat and non-flat substrates frequently act as dispersive elements in imaging spectrometers. We describe the design and electron-beam fabrication of blazed and computer-generated-hologram gratings for slit and tomographic imaging spectrometer.

Description: Light scattering off particles flowing through a two-slit inteference pattern can be used to measure the shear stress of the fluid. We have designed and fabricated a miniature diffractive optic sensor based on this principle.

Description: Diffractive optical elements fabricated on flat and non-flat substrates frequently act as dispersive elements in imaging spectrometers. We describe the design and electron-beam fabrication of blazed and computer-generated-hologram gratings for slit and tomographic imaging spectrometers.