ALBERT

Beschreibung: A multi-strand composite welding wire was applied to join high nitrogen austenitic stainless steel, and microstructures and mechanical properties were investigated. The electrical signals demonstrate that the welding process using a multi-strand composite welding wire is highly stable. The welded joints are composed of columnar austenite and dendritic ferrite and welded joints obtained under high heat input and cooling rate have a noticeable coarse-grained heat-affected zone and larger columnar austenite in weld seam. Compared with welded joints obtained under the high heat input and cooling rate, welded joints have the higher fractions of deformed grains, high angle grain boundaries, Schmid factor, and lower dislocation density under the low heat input and cooling rate, which indicate a lower tensile strength and higher yield strength. The rotated Goss (GRD) ({110}〈1 1 ¯ 0〉) orientation of a thin plate and the cube (C) ({001}〈100〉) orientation of a thick plate are obvious after welding, but the S ({123}〈63 4 ¯ 〉) orientation at 65° sections of Euler’s space is weak. The δ-ferrite was studied based on the primary ferrite solidification mode. It was observed that low heat input and a high cooling rate results in an increase of δ-ferrite, and a high dislocation density was obtained in grain boundaries of δ-ferrite. M23C6 precipitates due to a low cooling rate and heat input in the weld seam and deteriorates the elongation of welded joints. The engineering Stress–strain curves also show the low elongation and tensile strength of welded joints under low heat input and cooling rate, which is mainly caused by the high fraction of δ-ferrite and the precipitation of M23C6.

Beschreibung: Lakes and reservoirs are essential elements of the hydrological and biochemical cycles, considered sentinels of global climate change. However, comprehensive quantifications of their water storage changes (∆V) at a large spatiotemporal scale are still rare. Here, we integrated a global surface water dataset and SRTM digital elevation models, both available from Google Earth Engine platform at a spatial resolution of 30 m, to evaluate ∆V for a total of 760 lakes and reservoirs across China at an annual timescale since 1984. The results indicated that (1) the aggregated water storage went through a slight increase of 41.5 Gt (1.7 Gt/yr) during 1985–2005, a significant decrease of 100 Gt (−20.6 Gt/yr) during 2005–2009, and then increased by 136.3 Gt (21.3 Gt/yr) during 2009–2015. (2) The increasing trend was largely attributed to lakes and reservoirs in the Tibetan Plateau Lake Zone, and the decreasing trend was mainly due to the North and Northwest Lake Zone, with little variations observed for the Northeast and Southwest Lake Zones. (3) Qinghai lake was associated with the largest increase (18.3 Gt) and Poyang lake presented the largest decline (−9.2 Gt). The results can help advance our understanding of the impact of climate change and improve future projection.

Beschreibung: Geochemical anomalies play an important role in mineral exploration, because they are closely related to the formation of ore deposits. In this paper, the Au in the geochemical samples of 1:50,000 stream sediments in the Gouli exploration area, Qinghai Province, is selected as an example. The cumulative frequency method, local singularity analysis, and exploration data analysis method are used to process the Au data and determine the abnormal thresholds. Robust principal component analysis is used to explore the elemental associations. Among them, the effect of local singularity analysis is the best and it delineates the weak geochemical anomalies not delineated by cumulative frequency method and exploration data analysis method, which shows its superiority. Robust principal component analysis shows that Sb, W, and As are closely related to Au mineralization. Three anomalous areas are delineated in the Gouli exploration area. Gold ore-body is found to occur within anomaly area I. The other anomalous areas are highly consistent with abnormal elemental composition of Sb, W, and As. Moreover, these two areas are extremely conformable with the high-value areas determined by the binary state method. The optimality of the three methods are compared comprehensively, it is pointed out that it is more reasonable to use the local singularity analysis to determine the abnormal threshold. The anomaly areas II and III of Au determined by local singularity analysis have shown great potential for prospecting.

Beschreibung: The Proterozoic Xianglushan Fe-Cu orefield (western Sichuan) is located in the Huili–Dongchuan ore belt on the southwestern margin of the Yangtze Block in SW China. The orefield has experienced complex magmatotectonic activities, and hosts a wide variety of Fe oxide-(Cu-Au) deposits. At Xianglushan, the orebodies are made of stratabound magnetite–hematite orebodies superimposed by vein-type chalcopyrite mineralization. The stratabound Fe orebodies are hosted mainly in the Proterozoic volcanic-sedimentary rocks of the lower Yinmin Formation, whilst the Cu vein or stockwork ores were mainly emplaced into the upper part of the footwall volcanic rocks and the lower part of the Fe orebodies. We divided the alteration/mineralization and their fluid inclusions (FIs) into the (I) sodic-calcic alteration, (II) potassic-silicic-sericite alteration and Fe-(Cu) mineralization, and (III) carbonate alteration and Cu mineralization stages. Stage II FIs are mainly two-phase (vapor-liquid), and are featured by medium temperature (348 to 379 °C) and high salinity (21.8 to 22.9 wt % NaCl eqv). Their generally negative calcite δ13C (−4.1‰ to −3.1‰) and δ18OH2O (12.2‰ to 15.3‰) values reveal that the Stage II ore fluids have had a seawater-magmatic fluid mixed source. Late Stage II pyrite has δ34S (−3.3‰ to 13.7‰), 206Pb/204Pb (17.663 to 18.982), 207Pb/204Pb (15.498 to 15.824) and 208Pb/204Pb (37.784 to 38.985), suggesting that the ore-forming materials were derived from dominantly upper crustal source. Stage III FIs are also mainly two-phase (vapor-liquid), and are featured by lower temperature (206 to 267 °C) and salinity (19.0 to 22.5 wt % NaCl eqv) than their Stage II counterparts. The Stage III ore fluids were also likely derived from a meteoric–magmatic mixed source with greater magmatic influence, as indicated by the generally negative calcite δ13C (−6.9‰ to −4.6‰) and δ18OH2O (6.3‰ to 9.2‰) values. Similar to the late Stage II pyrite, the Stage III chalcopyrite δ34S (−4.6‰ to 5.2‰) and Pb isotopes (206Pb/204Pb = 18.198 to 18.987; 207Pb/204Pb = 15.534 to 15.876; and 208Pb/204Pb = 37.685 to 39.476) also suggest a crustal ore-forming material source. Therefore, we suggest that the Fe-(Cu) and Cu mineralization at Xianglushan had similar ore fluid and material sources, although the magmatic influence increased in the later stage. This resembles many Fe-(Cu) deposits in the Huili–Dongchuan ore belt. We conclude that the Xianglushan Fe-Cu deposits are both similar to and different from typical iron-oxide copper gold (IOCG) deposits in terms of alteration styles and hydrothermal mineral assemblages, and are thus best classified as IOCG-like deposits hosted in submarine volcanic-sedimentary rocks. Considering the Mesoproterozoic regional tectonics in the southwestern Yangtze Block, we propose that the Xianglushan ore formation occurred in an intra-/back-arc inversion setting, possibly related to the closure of the Anning ocean basin.

Beschreibung: The temperature distribution and deformation of the transformer windings cannot be measured in a distributed manner by the traditional method and failure location cannot be performed. To solve these problems, we present a transformer winding temperature and strain based on a distributed optical fibre sensing detection method. The design of the optical fibre winding composite model is developed and simulated winding temperature rise test and local deformation test distinguish between measuring the winding temperature and the strain curve. The test results show that the distributed optical fibre can transmit wire strain efficiently. Optical fibres, in the process of winding, have a certain pre-stress. Using the Brillouin–Raman joint measuring method, one can effectively extract the optical fibre temperature and strain information and measure the length of the winding direction of the temperature and strain distribution curve to a temperature measurement precision of ±2 °C and strain detection accuracy of ±50 με. The system can carry out local hot spot and deformation localisation, providing new ideas for the transformer winding state monitoring technology.

Beschreibung: The problem of air pollution is a persistent issue for mankind and becoming increasingly serious in recent years, which has drawn worldwide attention. Establishing a scientific and effective air quality early-warning system is really significant and important. Regretfully, previous research didn’t thoroughly explore not only air pollutant prediction but also air quality evaluation, and relevant research work is still scarce, especially in China. Therefore, a novel air quality early-warning system composed of prediction and evaluation was developed in this study. Firstly, the advanced data preprocessing technology Improved Complete Ensemble Empirical Mode Decomposition with Adaptive Noise (ICEEMDAN) combined with the powerful swarm intelligence algorithm Whale Optimization Algorithm (WOA) and the efficient artificial neural network Extreme Learning Machine (ELM) formed the prediction model. Then the predictive results were further analyzed by the method of fuzzy comprehensive evaluation, which offered intuitive air quality information and corresponding measures. The proposed system was tested in the Jing-Jin-Ji region of China, a representative research area in the world, and the daily concentration data of six main air pollutants in Beijing, Tianjin, and Shijiazhuang for two years were used to validate the accuracy and efficiency. The results show that the prediction model is superior to other benchmark models in pollutant concentration prediction and the evaluation model is satisfactory in air quality level reporting compared with the actual status. Therefore, the proposed system is believed to play an important role in air pollution control and smart city construction all over the world in the future.

Beschreibung: This study proposed a combined solar-assisted heat pump (SAHP) system that could operate in the serial mode or parallel mode. For this proposed system, a stable year-round operation could be achieved without the assistance of electric heating or low-temperature heat pump. By analyzing the heat balance equations, a correlation of the combined SAHP system for the two modes switched was obtained, which provided a theoretical basis for the optimal operation of this system. In addition, the performance of the proposed system applied in a university bathroom in Xi’an district was investigated using TRNSYS. The results illustrated that compared to the serial and parallel systems, the proposed system exhibited a good performance on energy efficiency. The annual average coefficient of performance (COP) of the proposed system was 5.7, obviously higher than those of the serial system and the parallel system, which were 3.3 and 4.3, respectively. Therefore, the results in this study could provide the theoretical guidance and reference for practical engineering design.

Beschreibung: The main purpose of this work was to investigate the microstructure and mechanical properties of spray-formed 2195-T6 Al-Li alloy welding joints produced by tungsten inert gas (TIG) with Al-Cu and Al-Si-Cu filler wires, so that they can be better used in space vehicle tanks. The porosity analysis indicates that the porosity area of the weld seam with the Al-Si-Cu filler wire is approximately 7.989 times larger than that of the Al-Cu filler wire. Furthermore, the microstructure and microhardness results indicate that the Al/Cu eutectic near the fusion line distributes more at the grain boundaries, while more dispersed Al2Cu phase is found inside the grain, which improves the strength of the joint when using Al-Cu filler wire. However, when using the Al-Si-Cu filler wire, more Si, Cu, and Ti elements are segregated at the grain boundaries, forming a brittle-hard network Al/Cu/Ti eutectic, which reduces the performance of the joint. Additionally, the tensile strength and elongation of the weld joint are about 68.6% and 89.9% of the base metal (BM) when using the Al-Cu filler wire, and can approach the level of friction stir welding (FSW). However, the tensile strength and elongation are only about 56.8% and 39.9%, respectively, of the BM in the weld joint when using the Al-Si-Cu filler wire. Lastly, the fractures both occur on the fusion line and the fracture morphology of the weld joint shows that it is a mixed fracture mode dominated by plastic fracture when using Al-Cu filler wire, while it is mainly a quasi-cleavage fracture mode when using Al-Si-Cu filler wire. Therefore, the joint strength when using Al-Si-Cu filler wire with high strength matching is not as good as that of Al-Cu filler wire with low strength matching.

Beschreibung: In the published article [1], the authors realized some errors in the affiliation and email address of Yang Hong, and thus wish to make the following revisions: Add the Affiliation 5 “School of Civil Engineering and Environmental Science, University of Oklahoma, Norman, OK 73019, USA” for Yang Hong Change the email address of Yang Hong to yanghong@ou [...]

Beschreibung: Understanding the mineralogical and chemical characteristics of stone coal is imperative for exploring the thermal storage characteristics of stone coal. Two types stone coal (SCwt and SChc) were sampled from the pond of a stone coal mine in Henan province (China), and the chemical composition, phase composition, and thermal behavior of the stone coal were investigated. Furthermore, the petrography of the stone coal was studied in detail. The mineral phases of the stone coal were quartz, kaolinite, roscoelite, and goethite, as distinguished by reflected light microscopy and further proven by scanning electron microscope-energy dispersive spectrometer (SEM-EDS). The thermal conductivity of SCwt was 0.19 W m−1 K−1, while that of SChc was 0.24 W m−1 K−1. Stearic acid (SA) was blended with SCwt and SChc to prepare SA/SCwt and SA/SChc composites via an impregnation method, respectively. The thermogravimetric (TG) curves show that the loading capacity of SChc, at 17.40%, is higher than that of SCwt (16.63%). The thermal energy storage capacities of SA/SCwt and SA/SChc composites were 29.21 J g−1 and 33.02 J g−1 according to a differential scanning calorimetry (DSC) analysis. Therefore, SChc is a potential candidate for thermal storage applications due to more obvious thermal storage characteristics, including higher thermal conductivity and loading capacity.